- Simplify MSI allocation to what is actually needed for a single one.
- Release the MSI and the corresponding bus resource as appropriate when
either the interrupt resource cannot be allocated or setting up the
interrupt fails.
- Error out when interrupt allocation or setup fails and polling is
disabled.
- Release the MSI after the corresponding bus resource so the former is
not leaked on detach.
- Remove a redundant softc member.
MFC after: 3 days
for the lookup.
- For devices affected by PCI_QUIRK_MSI_INTX_BUG, ensure PCIM_CMD_INTxDIS
is cleared when using MSI/MSI-X.
- Employ PCI_QUIRK_MSI_INTX_BUG for BCM5714(S)/BCM5715(S)/BCM5780(S) rather
than clearing PCIM_CMD_INTxDIS unconditionally for all devices in bge(4).
MFC after: 3 days
AR5416 and later NICs have more than 8 (Well, more than 6) GPIO pins.
So to support rfkill on these NICs we need to bump this up or the
rfkill GPIO pin may get reset to the wrong value.
Noticed by: Anthony Jenkins <scoobi_doo@yahoo.com>
deselect it after setting the block size. This is a similar bug that
was fixed elsewhere, but not here. This makes sure that we leave the
card deselected at the end of the loop, and we don't send any commands
to the card without it selected.
Reviewed by: ian@
Current VT drivers don't register the memory regions they use with the
nexus. This patch makes vt_vga and vt_efifb register the memory regions they
use.
This is needed (at least) for Xen support, since the FreeBSD kernel will try
to use the holes in the memory map to map memory from other domains and
setup it's grant table.
Sponsored by: Citrix Systems R&D
Reported by: sbruno
Tested by: emaste
Reviewed by: ray
PR: 195537
Differential Revision: https://reviews.freebsd.org/D1291
Previously ahci_attach returned a hard coded ENXIO instead of the value
from ahci_setup_interrupt. This is effectively a NOOP change as currently
ahci_setup_interrupt only ever returns 0 or ENXIO, so just there to protect
against any future changes to that.
Differential Revision: D838
MFC after: 2 weeks
Sponsored by: Multiplay
This prevents the possiblity of any overruns on the statically allocated
struct irqs field.
Differential Revision: D838
MFC after: 2 weeks
X-MFC-With: r276012
Sponsored by: Multiplay
such as timeouts while probing a bus or testing for a feature, is
squelched. Also, error reporting is limited to 5 events per second,
because when an sdcard goes bad on a low-end embedded board, flooding
the console at high speed isn't helpful.
Original logging code contributed by Michal Meloun, but then I fancied
it up with squelching and ppsratecheck.
TI OMAP controllers which will return the reset-in-progress bit as zero if
you read the status register too fast after setting the reset bit.
The zero is apparently from a stale snapshot of the internal state presented
in the interface register, and leads to a false indication that the reset
is complete when it either hasn't started yet or is in-progress. The
workaround is to first loop until the bit is seen as asserted, then do the
normal loop waiting to see it de-asserted.
Submitted by: Michal Meloun <meloun@miracle.cz>
function parameters, the card has to be in transfer state. If it is in
the idle state, the commands are ignored. This caused us not to set
the proper parameters that we later assume to be present, leading to
downstream failures of the card / interface as our state machine
mismatches the card's.
Submitted by: Svatopluk Kraus <onwahe at gmail.com>, Michal Meloun
<meloun at miracle.cz>
While we don't support MCS, hole in received sequence numbers may mean
only PDU loss. While we don't support lost PDU recovery, terminate the
connection to avoid stuck commands.
While there, improve handling of sequence numbers wrap after 2^32 PDUs.
MFC after: 2 weeks
sheet, RX filter should be disabled before programming.
Previously it was clearing wrong bits so RX filter was not
disabled in RX filter configuration.
Reported by: brad@OpenBSD.org
This allows the Grant-table code to attach directly to the xenpv bus,
allowing us to remove the grant-table initialization done in xenpv.
Sponsored by: Citrix Systems R&D
Mave the grant table code into the dev/xen folder in preparation for turning
it into a device using the newbus interface. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
When running as a Xen PVH Dom0 we need to add custom buses that override
some of the functionality present in the ACPI PCI Bus and the PCI Bus. We
currently override the ACPI PCI Bus, but not the PCI Bus, so add a new
override for the PCI Bus and share the generic functions between them.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
conf/files.amd64:
- Add the new files.
x86/xen/xen_pci_bus.c:
- Generic file that contains the PCI overrides so they can be used by the
several PCI specific buses.
xen/xen_pci.h:
- Prototypes for the generic overried functions.
dev/xen/pci/xen_pci.c:
- Xen specific override for the PCI bus.
dev/xen/pci/xen_acpi_pci.c:
- Xen specific override for the ACPI PCI bus.
o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
There are two main parts to get it to work, 1) most of the register
accesses need to be word sized, other than the config register which
needs to be byte aligned, and 2) we don't need the platform driver
for this to work on the Foundation Model, allow it to be NULL.
Differential Revision: https://reviews.freebsd.org/D1240
Reviewed by: bryanv
Sponsored by: The FreeBSD Foundation
adapters. Set the pack boundary for T5 cards to be the same as the
PCIe max payload size. The chip likes it this way.
In this revision the driver allocate rx buffers that align on both
boundaries. This is not a strict requirement and a followup commit
will switch the driver to a more relaxed allocation strategy.
MFC after: 2 weeks
re-using a hardware propritary transfer descriptor, PTD, in USB host
mode. If the PTD's are recycled too quickly, it has been observed that
the hardware simply fails to schedule the requested job or resets
completely disconnecting all devices.
Always include the card human readable name. We support ~270 cards and
at ~20 bytes each, this bloats things by only ~5k. Retain the
PCMCIA_CARD vs PCMCIA_CARD_D distinction, though, in case this is
intolerable.
from the FreeBSD network code. The flag is still kept around in the
"sys/mbuf.h" header file, but does no longer have any users. Instead
the "m_pkthdr.rsstype" field in the mbuf structure is now used to
decide the meaning of the "m_pkthdr.flowid" field. To modify the
"m_pkthdr.rsstype" field please use the existing "M_HASHTYPE_XXX"
macros as defined in the "sys/mbuf.h" header file.
This patch introduces new behaviour in the transmit direction.
Previously network drivers checked if "M_FLOWID" was set in "m_flags"
before using the "m_pkthdr.flowid" field. This check has now now been
replaced by checking if "M_HASHTYPE_GET(m)" is different from
"M_HASHTYPE_NONE". In the future more hashtypes will be added, for
example hashtypes for hardware dedicated flows.
"M_HASHTYPE_OPAQUE" indicates that the "m_pkthdr.flowid" value is
valid and has no particular type. This change removes the need for an
"if" statement in TCP transmit code checking for the presence of a
valid flowid value. The "if" statement mentioned above is now a direct
variable assignment which is then later checked by the respective
network drivers like before.
Additional notes:
- The SCTP code changes will be committed as a separate patch.
- Removal of the "M_FLOWID" flag will also be done separately.
- The FreeBSD version has been bumped.
MFC after: 1 month
Sponsored by: Mellanox Technologies
- Add support for GEOM direct completion. Depending on the benchmark,
this tends to give a ~30% improvement w.r.t IOPs and BW.
- Remove an invariants check in the strategy routine. This assertion
is caught later on by an existing panic.
- Rename and resort various related functions to make more sense.
MFC after: 1 month
sending not ready data:
o Add new flag to pru_send() flags - PRUS_NOTREADY.
o Add new protocol method pru_ready().
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
o Introduce a notion of "not ready" mbufs in socket buffers. These
mbufs are now being populated by some I/O in background and are
referenced outside. This forces following implications:
- An mbuf which is "not ready" can't be taken out of the buffer.
- An mbuf that is behind a "not ready" in the queue neither.
- If sockbet buffer is flushed, then "not ready" mbufs shouln't be
freed.
o In struct sockbuf the sb_cc field is split into sb_ccc and sb_acc.
The sb_ccc stands for ""claimed character count", or "committed
character count". And the sb_acc is "available character count".
Consumers of socket buffer API shouldn't already access them directly,
but use sbused() and sbavail() respectively.
o Not ready mbufs are marked with M_NOTREADY, and ready but blocked ones
with M_BLOCKED.
o New field sb_fnrdy points to the first not ready mbuf, to avoid linear
search.
o New function sbready() is provided to activate certain amount of mbufs
in a socket buffer.
A special note on SCTP:
SCTP has its own sockbufs. Unfortunately, FreeBSD stack doesn't yet
allow protocol specific sockbufs. Thus, SCTP does some hacks to make
itself compatible with FreeBSD: it manages sockbufs on its own, but keeps
sb_cc updated to inform the stack of amount of data in them. The new
notion of "not ready" data isn't supported by SCTP. Instead, only a
mechanical substitute is done: s/sb_cc/sb_ccc/.
A proper solution would be to take away struct sockbuf from struct
socket and allow protocols to implement their own socket buffers, like
SCTP already does. This was discussed with rrs@.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Call to the driver-specific ioctl used to process ioctl number
that will lead to the out-of-bounds access to the ioctl handler
array.
PR: 193367
Approved by: kib
MFC after: 1 week
This allows one to make a kernel module to tune the
number of queues before the driver loads.
This is needed so that a module at SI_SUB_CPU can set
tunables for these drivers to take. Otherwise getenv
is called too early by the TUNABLE macros.
Reviewed by: smh
Phabric: https://reviews.freebsd.org/D1149
Records with target_mode == 1 are allocated from the end of portdb, so it
seems logical to start search from the end not traverse whole array.
MFC after: 1 month
This was previously working by accident because BUSDMA_COHERENT_MEMORY has
always been set to strongly-ordered on arm. Now we're moving towards
normal-uncacheable (what might be called write-combining on other platforms)
and using the proper sync ops will be more important. Of course, that
opens the question of just what is the "proper" sync op for shared
concurrent dma access as opposed to accesses where the handoff of control
of the memory has well-defined sequence points that match the available
busdma sync operations.
ath kernel module:
sys/dev/ath/ath_hal/ar5212/ar5212_reset.c:2642:7: error: taking the absolute value of unsigned type 'unsigned int' has no effect [-Werror,-Wabsolute-value]
if (abs(lp[0] * EEP_SCALE - target) < EEP_DELTA) {
^
sys/dev/ath/ah_osdep.h:74:18: note: expanded from macro 'abs'
#define abs(_a) __builtin_abs(_a)
^
sys/dev/ath/ath_hal/ar5212/ar5212_reset.c:2642:7: note: remove the call to '__builtin_abs' since unsigned values cannot be negative
sys/dev/ath/ah_osdep.h:74:18: note: expanded from macro 'abs'
#define abs(_a) __builtin_abs(_a)
^
1 error generated.
This warning occurs because both lp[0] and target are unsigned, so the
subtraction expression is also unsigned, and calling abs() is a no-op.
However, the intention was to look at the absolute difference between
the two unsigned quantities. Introduce a small static function to
clarify what we're doing, and call that instead.
Reviewed by: adrian
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D1212
isochronous endpoint descriptor used for the data transfers, hence the
synchronization feature might not be supposed to be supported [yet].
This makes seamless playback synced with the USB HOST clock work with
the DN32-USB module for Midas audio systems and possibly other similar
products from Klark Teknik.
MFC after: 1 week
SAF1761 OTG driver. Currently the driver logic is very simple and
double buffering the USB transactions is not done. Also you need to
use an external USB high speed USB HUB for reliable FULL speed
outgoing ISOCHRONOUS traffic, because the internal one chokes on
so-called split transfers above 188 bytes.
establishing connection.
This is a workaround for Chelsio TOE driver, that does not update socket
buffer size in hardware after connection established, and unless that is
done beforehand, kernel code will stuck, attempting to send/receive full
PDU at once.
MFC after: 1 week
I've missed that iscsi_outstanding_remove() frees the second pointer,
so it should no longer be used. And in fact we don't really need to.
MFC after: 2 weeks
During heavy reads data copying in icl_pdu_get_data() may consume large
percent of CPU time. Moving it out of the lock significantly reduces
lock hold time and respectively lock congestion on read operations.
MFC after: 2 weeks
commit 6d3c4c09226ad6bdd662e3e52489ef294a6ce298
Add terasic_mtl vt(4) framebuffer driver
terasic_mtl can be built with syscons(4) and vt(4) attachments, selected
at compile time.
commit 33240259b47a7c990a5a88a19f133a5600432a4c
Clear terasic_mtl text buffer on attach
commit d188c2d2412953f949624aa35cd07082830943c9
Update terasic vt(4) driver for FreeBSD r269783
commit d1cc54eee852fa4fc9d359d5bb2171d24ec73369
Safety belt to ensure vt(4) fb parameters are correct
commit 76e6d468ef45711d7952786095fc4791289ebb4b
Improve terasic_mtl_vt fdt parsing
- Use OF_getencprop to avoid need for explicit endian handling
(submitted by ray@freebsd.org)
- Check for expected length and correct pointer type
commit 3e2524b8995ab66e8a9295e4c87cbc7126eeddf4
Correct device_printf usage
commit 9e53e3c8e0766414e25662c95b09cc51c92443b0
Switch framebuffer to match host endianness
Xorg and xf86-video-scfb work much better with a native-endian
framebuffer.
commit 0f49259d596321ed85288ac0e1fb4ee1c966df48
Switch DE4 to vt(4) and enable kbdmux
commit 5bc96ebc89db7d134ad478335090c8477c1677c7
Add missing \n in device_printf calls
Submitted by: emaste
Sponsored by: DARPA, AFRL
commit d0c7d235c09fc65dbdb278e7016a96f79c6a49cc
Make the Altera JTAG UART device driver slightly more forgiving of
the foibles of a sub-par hrdware interface by increasing the timeout
for spotting JTAG polling from one to two seconds.
commit 19ed45a18832560dab967c179d83b71081c3a220
Update comment.
commit 8edfe803f033cc8e33229f99894c2b7496a44d5f
Add a comment about a device-driver race condition that could cause the BERI
pipeline to wedge awaiting JTAG in the event that both the low-level console
and the tty layer decide to write to the JTAG FIFO just before JTAG is
disconnected. Resolving this race is a bit tricky as it looks like there
isn't a way to 'give the character back' to the tty layer when we discover
the race. The easy fix is to drop the character, which we don't yet do, but
perhaps should as that is a better outcome than wedging the pipeline.
commit 2ea26cf579c9defcf31e413e7c9b0fbc159237fc
Add a comment about an inherent race with hardware in the Altera JTAG
UART's low-level console code.
Submitted by: rwatson
MFC after: 1 week
Sponsored by: DARPA, AFRL
Previously, any timeout value for which (timeout * hz) will overflow the
signed integer, will give weird results, since callout(9) routines will
convert negative values of ticks to '1'. For unsigned integer overflow we
will get sufficiently smaller timeout values than expected.
Switch from callout_reset, which requires conversion to int based ticks
to callout_reset_sbt to avoid this.
Also correct isci to correctly resolve ccb timeout.
This was based on the original work done by Eygene Ryabinkin
<rea@freebsd.org> back in 5 Aug 2011 which used a macro to help avoid
the overlow.
Differential Revision: https://reviews.freebsd.org/D1157
Reviewed by: mav, davide
MFC after: 1 month
Sponsored by: Multiplay
related cleanups:
- Require each driver to initalize a mutex in the scsi_low_softc that
is shared with the scsi_low code. This mutex is used for CAM SIMs,
timers, and interrupt handlers.
- Replace the osdep function switch with direct calls to the relevant
CAM functions and direct manipulation of timers via callout(9).
- Collapse the CAM-specific scsi_low_osdep_interface substructure
directly into scsi_low_softc.
- Use bus_*() instead of bus_space_*().
- Return BUS_PROBE_DEFAULT from probe routines instead of 0.
- No need to zero softcs.
- Pass 0ul and ~0ul instead of 0 and ~0 to bus_alloc_resource().
- Spell "dettach" as "detach".
- Remove unused 'dvname' variables.
- De-spl().
Tested by: no one
- Don't recurse driver mutex.
- Don't hold driver mutex across fubyte/subyte.
- Replace fubyte/subyte loops with copyin/copyout calls.
- Use relatively sane locking in wl_ioctl().
- Use bus space accessors instead of in*()/out*().
- Use callout(9) instead of timeout(9).
- Stop watchdog timer in detach and don't hold mutex across
bus_teardown_intr().
- Use device_printf() and if_printf().
- De-spl().
Tested by: no one
node. Take this in to account by searching until we find the range for the
root node.
Differential Revision: https://reviews.freebsd.org/D1160
Reviewed by: ian
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
- Add per-softc mutex.
- Use mutex for CAM SIM lock.
- Use bus_*() instead of inb() and outb().
- Use bus_alloc_resource_any() when reasonable.
Tested by: no one
- Actually use existing per-softc mutex.
- Use mutex in cdev routines and remove D_NEEDGIANT.
- Use callout(9) instead of timeout(9).
- Don't check for impossible conditions (e.g. SCDINIT being clear).
- Use bus_*() instead of bus_space_*().
Tested by: no one
- Add a per-softc mutex.
- Use mutex as CAM sim lock.
- Use taskqueue_thread instead of taskqueue_swi_giant.
- Use callout(9) instead of timeout(9).
- Use bus_*() instead of bus_space_*().
Tested by: no one
- Actually use existing per-softc mutex.
- Use mutex in cdev routines and remove D_NEEDGIANT.
- Use callout(9) instead of timeout(9).
- Don't check for impossible conditions (e.g. MCDINIT being clear).
- Remove critical_enter/exit when sending a PIO command.
- Use bus_*() instead of bus_space_*().
Tested by: no one
The current support for controlling i2c bus speed is an inconsistant mess.
There are 4 symbolic speed values defined, UNKNOWN, SLOW, FAST, FASTEST.
It seems to be universally assumed that SLOW means the standard 100KHz
rate from the original spec. Nothing ever calls iicbus_reset() with a
speed of FAST, although some drivers would treat it as the 400KHz standard
speed. Mostly iicbus_reset() is called with the speed set to UNKNOWN or
FASTEST, and there's really no telling what any individual driver will do
with those.
The speed of an i2c bus is limited by the speed of the slowest device on
the bus. This means that generally the bus speed needs to be configured
based on the board/system and the components within it. Historically for
i2c we've configured with device hints. Newer systems use FDT data and it
documents a clock-frequency property for i2c busses. Hobbyists and
developers are likely to want on the fly changes. These changes provide
all 3 methods, but do not require any existing drivers to change to use
the new facilities.
This adds an iicbus method, iicbus_get_frequency(dev, speed) that gets the
frequency for the requested symbolic speed. If the symbolic speed is SLOW
or if there is no speed configured for the bus, the returned value is
100KHz, always. Otherwise, if bus speed is configured by hints, fdt,
tunable, or sysctl, that speed is returned. It also adds a helper
function, iicbus_init_frequency() that any bus driver subclassed from
iicbus can initialize the frequency from some other source of info.
Initial driver implementations are provided for Freescale and TI.
Differential Revision: https://reviews.freebsd.org/D1174
PR: 195009
This is the general support to allow the use of GPIO pins as interrupt
sources for direct gpiobus children.
The use of GPIO pins as generic interrupt sources (for an ethernet driver
for example) will only be possible when arm/intrng is complete. Then, most
of this code will need to be rewritten, but it works for now, is better
than what we have and will allow further developments.
Tested on: ar71xx (RSPRO), am335x (BBB), bcm2835 (Raspberry pi)
Differential Revision: https://reviews.freebsd.org/D999
Reviewed by: rpaulo
Due to adapter->hw.fc.requested_mode is filled with default value
after ixgbe_initialize_receive_units(), this leads to enabling
DROP_EN in most cases.
Tested by: ae
MFC after: 1 week
Like in r259717, the prority goes from "error" to "debug" to avoid
spamming logs when the connectors are polled.
PR: 194770
Submitted by: Larry Rosenman <ler@lerctr.org>
MFC after: 1 week
I did this wrong - I should've included a state flag for each callout
to see if it was supposed to run or not. I didn't do that.
Instead, just use mutexes anyway.
Suggested by: jhb
- Add a per-device mutex to the softc and use it for bus_dma tags,
CAM SIMs, callouts, and interrupt handler.
- Switch from timeout(9) to callout(9).
- Add a separate global mutex to protect the global event buffer ring.
- Return completed index from iir_intr_locked() and remove the global
gdt_wait_* variables.
- Remove global list of gdt softcs and replace its use with
devclass_get_device().
- Use si_drv1 to store softc pointer in the SDEV_PER_HBA case instead
of minor numbers.
- Do math on osreldate instead of dubious char math on osrelease[]
that didn't work on 10.0+.
- Use bus_*() instead of bus_space_*().
- Use device_printf() instead of printf() with a unit number.
Tested by: no one
to the build in either sys/conf/files* or sys/modules/dpt/Makefile. Also,
it was denoted as "doesn't quite work yet" when the file was initially added
(which may account for it never having been hooked up to the build).
have both kern_open() and kern_openat(); change the callers to use
kern_openat().
This removes one (sometimes two) levels of indirection and
consolidates arguments checks.
Reviewed by: mckusick
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
leave a port permanently disabled when a copper cable is unplugged and
then plugged right back in.
lacp_linkstate goes looking for the current ifmedia on a link state
change and it could get stale information from cxgbe(4) on a module
unplug followed by replug. The fix is to process module events before
link-state events within the driver, and to always rebuild the ifmedia
list on a module change event (instead of rebuilding it lazily).
Thanks to asomers@ for the problem report and detailed analysis to go
with it.
MFC after: 1 week
This will allow to attach UART drivers lying directly on the root node
instead of simple-bus compatible bus only.
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Instead of waiting for empty TX FIFO it is more reasonable to
block on full FIFO. As soon as FIFO slot is free the character
can be transmitted.
In case of TX FIFO disabled, TXFF bit indicates that transmit
register is not empty.
Obtained from: Semihalf
Reviewed by: andrew, emaste
Sponsored by: The FreeBSD Foundation
sb_cc member of struct sockbuf to a couple of inline functions:
sbavail() and sbused()
Right now they are equal, but once notion of "not ready socket buffer data",
will be checked in, they are going to be different.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
convert a global timer to a per-controller timer. This works much better
with locking and removes the need for several global lookup tables.
Tested by: ambrisko
state said device should go into.
This was a snafu introduced in the ACPI/PCI awareness separation.
When putting a device into a power state, the bus (and thus firmware,
eg ACPI) should be asked before hand to check whether the device
can indeed go into that power state.
There's a set of nodes in ACPI under each device - the _SxD nodes - which
state which ACPI power state to put the device into when the system is
going into power save state 'x'. So when going into S3, the existence
of an _S3D node would override whatever the system was trying to do.
By default the PCI code wants to put devices into D3 before suspending.
I have a laptop here (Asus Zenbook - check the PR) whose EHCI controller
really wants to be in D2 during suspend, not D3. So if we put it into
D3 and then try to enter S3, everything hangs. The device itself
can go into D3 - it just can't be there when the call to ACPI to enter
S3 occurs. The PCI patch fixes this.
jkim@ noticed that the same is needed for the ACPI child device
enumeration.
Thankyou to Matt Dillon (the programmer, not the actor) for buying me
this particular laptop so I could debug the issues with the Atheros
AR9485 that is in it. It's his fault that I ended up with this
laptop and was sufficiently annoyed by the lack of USB suspend
to go down this rabbit hole.
Tested:
* Thinkpad T400
* Thinkpad X230
* Thinkpad T42
* Thinkpad T60
* Asus Zenbook (see PR)
* Asus EEEPC 701
* Asus EEEPC 1001PX
TODO:
* Figure out what we should do about devices we unload drivers for
that want to be in a specific state when entering S3 / S4 -
the "put devices into D3 if they're not bound to a driver" option
may also mess with things.
PR: kern/194884
Reviewed by: jhb, jkim
MFC after: 1 week
Relnotes: yes
Sponsored by: Matt Dillon <dillon@apollo.backplane.com> (hardware)
IGP may declare subclass as either VGA-compatible, or non-VGA. The
difference is that in the later case, IGP does not claim VGA cycles.
Other than that, the device functions normally, and agp_i810 should
attach to it.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
was possible for a regular user to setup the dump device if he had write access
to the given device. In theory it is a security issue as user might get access
to kernel's memory after provoking kernel crash, but in practise it is not
recommended to give regular users direct access to storage devices.
Rework the code so that we do privileges check within the set_dumper() function
to avoid similar problems in the future.
Discussed with: secteam
The prior change to not enable LRO by default has confused several
people. The configurations where LRO is problematic is not the
typical use case for VirtIO, and due to other issues, this often
requires checksum offloading to be disabled anyways.
PR: 185864
MFC after: 2 weeks
- Remove duplicated sources between standard part of the kernel and
module. In particular, it caused duplicated lock initialization and
sysctl registration, both having bad consequences.
- Add missed source files to module.
- Static part of the kernel provides randomdev module, not
random_adaptors. Correct dependencies.
- Use cdev modules declaration macros.
Approved by: secteam (delphij)
Reviewed by: markm
buffer from asm to C, which reduces amount of arguments for inline asm
and simplifies constraints. Use unsigned types consistently.
Submitted by: bde
Approved by: secteam (delphij)
Reviewed by: markm
MFC after: 1 week
After resource allocation and release, resource list entry
stays non-NULL. This causes panic in ofwbus_alloc_resource()
on subsequent resource allocation.
Clean appropriate list entry on release to avoid this.
Obtained from: Semihalf
Reviewed by: ian
Sponsored by: The FreeBSD Foundation
it, except Ethernet, where it carried ng_ether(4) pointer.
For now carry the pointer in if_l2com directly.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
- Support the KDB alt break sequence to enter the debugger,
panic, reboot, etc. [1]
- Provide emergency write feature description. Note that QEMU
does not implement this feature.
- Make the VTCON_FLAG_* defines sequential once again.
- When the multiple port feature is not negotiated, query the
rows and columns of the one console during the device attach
when the size feature is negotiated.
- Report failure to the device if hot plugging a port fails.
- Acknowledge the console port event with an open event. This
is required by the spec, but QEMU doesn't seem to care.
Submitted by: Juniper [1]
MFC after: 1 month
-Improved VF stability, thanks to changes from Ryan Stone,
and Juniper.
- RSS fixes in the ixlv driver
- link detection in the ixlv driver
- New sysctl's added in ixl and ixlv
- reset timeout increased for ixlv
- stability fixes in detach
- correct media reporting
- Coverity warnings fixed
- Many small bug fixes
- VF Makefile modified - nvm shared code needed
- remove unused sleep channels in ixlv_sc struct
Submitted by: Eric Joyner (committed by jfv)
MFC after: 1 week
Therefore, to set histry size to 2000 lines, add the following line to
your kernel configuration file:
options SC_HISTORY_SIZE=2000
The default history remains at 500 lines.
MFC after: 1 week
some accumulated entropy twice and use that as the new key. Due to a
typo, we were using the output of the first hash round instead of the
second. Correct this, but eliminate temp[] since we can reuse hash[].
Also add comments explaining what is going on and why.
Noticed by: Sami Farin <sami.farin@gmail.com>
Reviewed by: markm@
Approved by: so (des)
on my part about north bridge/GPU pci ids and use of aperture.
Leave the agp_intel.c out of static compilation on amd64, it makes the
things consistent with agp.ko.
Pointed out by: tijl
Sponsored by: The FreeBSD Foundation
MFC after: 13 days
... and their associated tunables. This gives a way to know the list of
available connectors, no matter the driver.
The problem is that xrandr(1) can list connectors but it uses a
different naming.
MFC after: 1 week
875. This intersects with the agp_i810.c, which supports all Intels
from i810 to Core i5/7. Both agp_intel.c and agp_i810.c are compiled
into kernel when device agp is specified in config, and agp_i810
attach seems to be selected by chance due to linking order.
Strip support for 810 and later from agp_intel.c. Since 440-class
chipsets do not support any long-mode capable CPUs, remove agp_intel.c
from amd64 kernel file list. Note that agp_intel.c is not compiled
into agp.ko on amd64 already.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
By default, vt(4) gets the "preferred mode" from DRM, when using a DRM
video driver as its backend. The preferred mode is usually the native
screen resolution.
Now, if this mode isn't appropriate, a user can use loader tunables to
select a mode. The tunables are read in the following order:
1. kern.vt.fb.modes.$connector_name
2. kern.vt.fb.default_mode
For example, to set a 1024x768 mode, no matter the connector:
kern.vt.fb.default_mode="1024x768"
To set a 800x600 mode only on the laptop builtin screen:
kern.vt.fb.modes.LVDS-1="800x600"
MFC after: 1 week
random_adaptors_lock is held.
- Use sx_sleep instead of tsleep in read and write path to allow
another thread that registers a new random adapter when waiting.
Assert that random_adaptor is not NULL after reacquiring the lock.
- Capture EINTR/ERESTART from sx_sleep to allow the blocking cycle be
stopped when user requests so, while there also make short
read/write's return 0.
- Move M_WAITOK allocations out of lock scope.
In collobration with: kib, markm, ian, jilles
Reviewed by: kib, markm
Approved by: so
The problem was that only the kbdmux keyboard index was saved in
vd->vd_keyboard. This index is -1 when kbdmux isn't used. In this
case, the keyboard was correctly allocated, but the returned index was
discarded.
PR: 194718
MFC after: 1 week
updating the GTT and flushing the AGP TLB by storing the GTT in
write-combining memory.
On x86 flushing the AGP TLB is done by an I/O operation or a store to a
MMIO register in uncacheable memory. Both cases imply that WC buffers are
flushed so no memory barriers are needed.
On powerpc there is no WC memory type. It maps to uncacheable memory and
two stores to uncacheable memory, such as to the GTT and then to an MMIO
register, are strongly ordered, so no memory barriers are needed either.
MFC after: 1 month
A new terminal_set_cursor() is added: it wraps the existing
teken_set_cursor() function.
In vtbuf_grow(), the cursor position is adjusted at the end of the
function. In vt_change_font(), we call terminal_set_cursor() just after
terminal_set_winsize_blank(), while the terminal is mute.
This fixes a bug where, after loading a kernel video driver which
increases the terminal window size, the cursor remains at its old
position, in other words, in the middle of the display content.
PR: 194421
MFC after: 1 week
hold the gpiobus lock between the gpio calls.
gpiobus_acquire_lock() now accepts a third parameter which tells gpiobus
what to do when the bus is already busy.
When GPIOBUS_WAIT wait is used, the calling thread will be put to sleep
until the bus became free.
With GPIOBUS_DONTWAIT the calling thread will receive EWOULDBLOCK right
away and then it can act upon.
This fixes the gpioiic(4) locking issues that arises when doing multiple
concurrent access on the bus.
This code has had an extensive rewrite and a good series of reviews, both by the author and other parties. This means a lot of code has been simplified. Pluggable structures for high-rate entropy generators are available, and it is most definitely not the case that /dev/random can be driven by only a hardware souce any more. This has been designed out of the device. Hardware sources are stirred into the CSPRNG (Yarrow, Fortuna) like any other entropy source. Pluggable modules may be written by third parties for additional sources.
The harvesting structures and consequently the locking have been simplified. Entropy harvesting is done in a more general way (the documentation for this will follow). There is some GREAT entropy to be had in the UMA allocator, but it is disabled for now as messing with that is likely to annoy many people.
The venerable (but effective) Yarrow algorithm, which is no longer supported by its authors now has an alternative, Fortuna. For now, Yarrow is retained as the default algorithm, but this may be changed using a kernel option. It is intended to make Fortuna the default algorithm for 11.0. Interested parties are encouraged to read ISBN 978-0-470-47424-2 "Cryptography Engineering" By Ferguson, Schneier and Kohno for Fortuna's gory details. Heck, read it anyway.
Many thanks to Arthur Mesh who did early grunt work, and who got caught in the crossfire rather more than he deserved to.
My thanks also to folks who helped me thresh this out on whiteboards and in the odd "Hallway track", or otherwise.
My Nomex pants are on. Let the feedback commence!
Reviewed by: trasz,des(partial),imp(partial?),rwatson(partial?)
Approved by: so(des)
in the radeonkms driver.
Note: In PCI mode virtual addresses on the graphics card that map to system
RAM are translated to physical addresses by the graphics card itself. In
AGP mode address translation is done by the AGP chipset so fictitious
addresses appear on the system bus. For the CPU cache management to work
correctly when the CPU accesses this memory it needs to use the same
fictitious addresses (and let the chipset translate them) instead of using
the physical addresses directly.
Reviewed by: kib
MFC after: 1 month
initial MPA exchange must be tracked this way so that t4_tom's state for
the tid is all clean at the time the tid transitions to RDMA mode. Once
it does, t4_tom is out of the way and iw_cxgbe uses the qp endpoints
directly.
Sponsored by: Chelsio Communications
directly accessed. Although this will work on some platforms, it can
throw an exception if the pointer is invalid and then panic the kernel.
Add a missing SYSCTL_IN() of "SCTP_BASE_STATS" structure.
MFC after: 3 days
Sponsored by: Mellanox Technologies
- Free rt in c4iw_connect only if it is allocated.
- Call soclose instead of so_shutdown if there is an abort from the peer.
- Close socket and return failure if TOE is not enabled.
Submitted by: Hariprasad at Chelsio dot com
Sponsored by: Chelsio Communications
transfers to be default. It simplifies porting code which assumes
such settings.
Discussed with: avg, llos, nwhitehorn
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
It had two bugs: one where mmap was still allowed and another where
D_TRACKCLOSE doesn't handle all cases.
Thanks to jhb and kib for pointing them out.
MFC after: 1 week
In some cases, TSC is broken and special applications might benefit
from memory mapping HPET and reading the registers to count time.
Most often the main HPET counter is 32-bit only[1], so this only gives
the application a 300 second window based on the default HPET
interval.
Other applications, such as Intel's DPDK, expect /dev/hpet to be
present and use it to count time as well.
Although we have an almost userland version of gettimeofday() which
uses rdtsc in userland, it's not always possible to use it, depending
on how broken the multi-socket hardware is.
Install the acpi_hpet.h so that applications can use the HPET register
definitions.
[1] I haven't found a system where HPET's main counter uses more than
32 bit. There seems to be a discrepancy in the Intel documentation
(claiming it's a 64-bit counter) and the actual implementation (a
32-bit counter in a 64-bit memory area).
MFC after: 1 week
Relnotes: yes
search (i.e. without returning any result) and you would end up with a
random MAC address.
Change the search algorithm to a recursive one to ensure that all the nodes
on DTS will be verified.
The previous algorithm could not keep up if the DTS has too many sub-nodes.
While here, fix the punctuation on comments.
To restore the default font using vidcontrol(1), use the "-f" flag
without an argument:
vidcontrol -f < /dev/ttyv0
PR: 193910
Differential Revision: https://reviews.freebsd.org/D971
Submitted by: Marcin Cieslak <saper@saper.info>
Reviewed by: ray@, emaste@
Approved by: ray@
MFC after: 1 week
Support for the multiport feature is mostly implemented, but currently
disabled due to some potential races in the hot plug code paths.
Requested by: marcel
MFC after: 1 month
Relnotes: yes
Current FreeBSD netback names the interface with xnb<device unit>, but
this is not suitable for usage with the Xen toolstack, which expects
something similar to <prefix><domid><handle>. In order to solve this,
change the netback naming convention to use xnb<domid>.<handle>.
Sponsored by: Citrix Systems R&D
dev/xen/netback/netback.c:
- Change netback to use the nomenclature stated above.
This device is only attached to priviledged domains, and allows the
toolstack to interact with Xen. The two functions of the privcmd
interface is to allow the execution of hypercalls from user-space, and
the mapping of foreign domain memory.
Sponsored by: Citrix Systems R&D
i386/include/xen/hypercall.h:
amd64/include/xen/hypercall.h:
- Introduce a function to make generic hypercalls into Xen.
xen/interface/xen.h:
xen/interface/memory.h:
- Import the new hypercall XENMEM_add_to_physmap_range used by
auto-translated guests to map memory from foreign domains.
dev/xen/privcmd/privcmd.c:
- This device has the following functions:
- Allow user-space applications to make hypercalls into Xen.
- Allow user-space applications to map memory from foreign domains,
this is accomplished using the newly introduced hypercall
(XENMEM_add_to_physmap_range).
xen/privcmd.h:
- Public ioctl interface for the privcmd device.
x86/xen/hvm.c:
- Remove declaration of hypercall_page, now it's declared in
hypercall.h.
conf/files:
- Add the privcmd device to the build process.
The user-space event channel device is used by applications to receive
and send event channel interrupts. This device is based on the Linux
evtchn device.
Sponsored by: Citrix Systems R&D
xen/evtchn/evtchn_dev.c:
- Remove the old event channel device, which was already disabled in
the build system.
dev/xen/evtchn/evtchn_dev.c:
- Import a new event channel device based on the one present in
Linux.
- This device allows the following operations:
- Bind VIRQ event channels (ioctl).
- Bind regular event channels (ioctl).
- Create and bind new event channels (ioctl).
- Unbind event channels (ioctl).
- Send notifications to event channels (ioctl).
- Reset the device shared memory ring (ioctl).
- Unmask event channels (write).
- Receive event channel upcalls (read).
- The new code is MP safe, and can be used concurrently.
conf/files:
- Add the new device to the build system.
the r241987 commit message, instead of having users locally overriding
the value using tunables in /boot/loader.conf .
Found by: Adam Parco
Discussed with: Nick Hibma
the Microsoft Azure service does not recognize the second
attached disk on the system.
Submitted by: kyliel@Microsoft
Patched by: weh@Microsoft
PR: 194376
MFC after: 3 days
X-MFC-10.1: yes, ASAP
Sponsored by: The FreeBSD Foundation
- Wrong integer type was specified.
- Wrong or missing "access" specifier. The "access" specifier
sometimes included the SYSCTL type, which it should not, except for
procedural SYSCTL nodes.
- Logical OR where binary OR was expected.
- Properly assert the "access" argument passed to all SYSCTL macros,
using the CTASSERT macro. This applies to both static- and dynamically
created SYSCTLs.
- Properly assert the the data type for both static and dynamic
SYSCTLs. In the case of static SYSCTLs we only assert that the data
pointed to by the SYSCTL data pointer has the correct size, hence
there is no easy way to assert types in the C language outside a
C-function.
- Rewrote some code which doesn't pass a constant "access" specifier
when creating dynamic SYSCTL nodes, which is now a requirement.
- Updated "EXAMPLES" section in SYSCTL manual page.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Before, the font was loaded and the window size recalculated, giving an
unusable terminal, even if the actual font didn't change.
Reported by: beeessdee@ruggedinbox.com
MFC after: 3 days
Increasingly, FDT data has the "simple-bus" compatible string on nodes
that have children, but we wouldn't consider them to be busses. If the
node lacks a ranges property then we will fail to attach successfully,
so fail to probe as well.
consistent with pmc_destroy_owner_descriptor(). Also be sure to destroy
PMCs if a process exits or execs without explicitly releasing them.
Reviewed by: bz, gnn
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D958
Previously, if no drivers attached at boot we would panic with
"vtbuf_fill_locked begin.tp_row 0 must be < screen height 0".
PR: 192248
Reviewed by: ray
MFC after: 3 days
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D954
used to align partitions in gpart. We also try to align partitions by
stripe size when creating new media. Align these two concepts by
making fwsectors the same as the stripe size. Select a sensible number
of heads so we wind up with about 20 cylinders. This number was
selected to keep the rounding effects to a few percent while keeping
the number of cylinder groups low.
Sadly, it is not possible to make these numbers match the numbers used
by SD card readers. There apperas to be much variation between brands
so there's no one universal number. These numbers are also not aligned
to the stripe size, so some performance problems may still be present
when SD cards are created this way.
Also, these numbers will differ from the far less common SD to ATA
adapters, which present a different, but more uniform, set of numbers
that also happened to match the old defaults.
Nothing should change for current users. Any suboptimal performance
caused by misalignment will still be there. gpart will honor the
partitions that aren't on proper boudnaries, but editing the partition
tables may result in different alignments being used than before when
editing things natively.
Ideally, there'd be some way to override these values in the disk
subsystem by the user for the USB adapter use case where all "native"
notions of geometry disappear. This does not implement that.
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
For compatibility, 'device windtunnel' is still supported, but one should use
'device adm1030' instead, and this has been updated in GENERIC and NOTES.
Mellanox hardware driver(s):
- Properly name an inclusion guard
- Fix compile warnings regarding unsigned enums
- Add two new sysctl nodes
- Remove all empty linux header files
- Make an error printout more verbose
- Use "mod_delayed_work()" instead of
cancelling and starting a timeout.
- Implement more Linux scatterlist
functions.
MFC after: 3 days
Sponsored by: Mellanox Technologies
He noticed issues setting this bit in SRRCTL after the queue was up,
so doing it from the sysctl handler isn't enough and may not actually
work correctly.
This commit doesn't remove the sysctl path or try to change its
behaviour. I'll talk with others about how to finish fixing that
before I tackle that.
PR: kern/194311
Submitted by: luigi
MFC after: 3 days
Sponsored by: Norse Corp, Inc
This is a duplicate variable reference in mrsas, so now this patch isolate atomic_ variable and relavent
function call using prefix mrsas_xx.
Issue was introduced in r272737.
MFC after: 2 weeks
Sponsored by: Avago Technology
There's a very remote, but possible, chance that the integer part read will
fail, but the fraction read succeeds, at which point the reported temperature is
invalid.
Reported by: Matthew Rezny
MFC after: 3 weeks
- Add a mutex to protect the softc.
- Use callout(9) instead of timeout(9).
- Consolidate duplicated detach routines into a bus-independent detach
routine.
- Add an extra sleep lock flag (MSESC_READING) to prevent other readers
from reading while the first reader is copying data out of sc_bytes[]
via uiomove().
- Use bus_*() instead of bus_space_*().
Tested by: nyan
- Read the counts of received, dropped, and transmitted management
packets and add sysctl nodes for them.
- Fix the total octets received/transmitted to read all 64 bits of
the counters.
- Add missing sysctl nodes for rlec, tncrs, fcruc, tor, and tot.
- Remove spurious spaces.
Reviewed by: Eric Joyner @ Intel
MFC after: 1 week
It allows to push out some final data from the send queue to the socket
before its close. In particular, it increases chances for logout response
to be delivered to the initiator.
* Add a bus_if.m method - get_domain() - returning the VM domain or
ENOENT if the device isn't in a VM domain;
* Add bus methods to print out the domain of the device if appropriate;
* Add code in srat.c to save the PXM -> VM domain mapping that's done and
expose a function to translate VM domain -> PXM;
* Add ACPI and ACPI PCI methods to check if the bus has a _PXM attribute
and if so map it to the VM domain;
* (.. yes, this works recursively.)
* Have the pci bus glue print out the device VM domain if present.
Note: this is just the plumbing to start enumerating information -
it doesn't at all modify behaviour.
Differential Revision: D906
Reviewed by: jhb
Sponsored by: Norse Corp
forced invalidation of the cache range regardless of the presence of
self-snoop feature. Some recent Intel GPUs in some modes are not
coherent, and dirty lines in CPU cache must be flushed before the
pages are transferred to GPU domain.
Reviewed by: alc (previous version)
Tested by: pho (amd64)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
where as there are limited number(32) of mfi commands in the pool.
The mfi command pool is now restricted to 27 simultaneous accesses by using
a counting semaphore while calling the passthru function.
In the mrsas_cam.c source file there was a same function name mrsas_poll(),
which was same as the mrsas_poll() implemented in the mrsas.c file for the
polling interface.
To clearly distinguish the functionality by usage we have renamed the former
as mrsas_cam_poll().
In the passthru function let's say it has got an mfi command from the pool
but it has failed in one of the DMA function call which will lead to leak
an mfi command because in the ERROR case it directly returns and not freeing up
the occupied mfi command.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
It is meant to notify the applications which will be waiting for some
controller events to be occured.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
This Driver will create multiple MSI-x vector depending upon what FW expose.
As of now 12 Gbp/s MR controller (Invader and Fury) expose 96 msix vector.
As of now 6 Gbp/s MR controller (Thunderbolt) expose 16 msix vector.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
snv add, so I have added $FreeBSD$ as comment.
This commit is contininous of last mrsas commit, so that compilation
does not break.
Obtained from: AVAGO Technologies
MFC after: 2 weeks
machine, for which 32bit compatibilty code has been added.
As in linux there is only one device entry that is used to fire IOCTL commands,
a new device entry megaraid_sas_ioctl_node is added for solely this
purpose.
From one dev node i.e mrgaraid_sa_ioctl_node we have to find out the
controller instance in case of multicontroller, for which one management info
structure has been added.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
E.g: If the user wants to create more than 64VD on a controller,
it is not possible on current firmware/driver.
New feature and requirement to support upto 256VD, firmware/driver/apps need changes.
In addition to that, there must be a backward compatibility of the new driver with the
older firmware and vice versa.
RAID map is the interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives.
In the earlier design driver was using the FW copy of RAID map where as
in the new design the Driver will keep the RAID map copy of its own; on which
it will operate for any raid map access in fast path.
Local driver raid map copy will provide ease of access through out the code
and provide generic interface for future FW raid map changes.
For the backward compatibility driver will notify FW that it supports 256VD
to the FW in driver capability field.
Based on the controller properly returned by the FW, the Driver will know
whether it supports 256VD or not and will copy the RAID map accordingly.
At any given time, driver will always have old or new Raid map.
Reviewed by : ambrisko
MFC after : 2 weeks
Sponsored by: AVAGO Technologies
These controllers seem to have the same feature of AR813x/AR815x and
improved RSS support(4 TX queues and 8 RX queues). alc(4) supports
all hardware features except RSS. I didn't implement RX checksum
offloading for AR816x/AR817x just because I couldn't get
confirmation from the Vendor whether AR816x/AR817x corrected its
predecessor's RX checksum offloading bug on fragmented packets.
This change adds supports for the following controllers.
o AR8161 PCIe Gigabit Ethernet controller
o AR8162 PCIe Fast Ethernet controller
o AR8171 PCIe Gigabit Ethernet controller
o AR8172 PCIe Fast Ethernet controller
o Killer E2200 Gigabit Ethernet controller
Tested by: Many
Relnotes: yes
MFC after: 2 weeks
HW donated by: Qualcomm Atheros Communications, Inc.
cannot be sent to the chip because a prerequisite L2 resolution
failed.
Submitted by: Hariprasad at chelsio dot com (original version)
MFC after: 2 weeks.
E5372 with different product IDs.
Interestingly, the standard E5372 IDs (12d1:1506) are currently listed in
u3g.c and are the same as the E3131. However, the R215/E5372 is an NCM
device and works well with cdce(4) whereas the E3131 isn't. More work
may be needed to better identify the other device IDs.
MFC after: 1 week
events we have actually counted 'Branch Instruction Retired' when people
asked for 'Unhalted core cycles' using the 'unhalted-core-cycles' event mask
mnemonic.
Reviewed by: jimharris
Discussed with: gnn, rwatson
MFC after: 3 days
Sponsored by: DARPA/AFRL
It was found that VirtualBox' AHCI does not allow nterrupt to be cleared
before the interrupt status register is read, causing interrupt storm.
AHCI specification allows to skip this register use when multi-vector MSI
is enabled and so interrupting port is known. For single-vector MSI that
is not stated explicitly, but if the port is only one, it is obviously
known too.
When the screen size is unknown, it's set to 0x0. We can't use that as
the buffer size, otherwise, functions such as vtbuf_fill() will fail.
This fixes a panic on RaspberryPi, where there's no vt(4) backend
configured early in boot.
PR: 193981
Tested by: danilo@
MFC after: 3 days
ports. The current bitmap array was too small to hold more than 16
bits and would at some point toggle the context size, which then would
trigger an enumeration fault and cause a fallback to the EHCI
companion controller, if any.
MFC after: 3 days
Add new functions to manipulate these mode & state, instead of calling
kbdd_ioctl() everyhere.
This fixes at least two bugs:
1. The state of the Scroll Lock LED and the state of scroll mode
could be out-of-sync. For instance, if one enables scroll mode on
window #1 and switches to window #2, the LED would remain on, but
the window wouldn't be in scroll mode.
Similarily, when switching between a console and an X.Org
session, the LED states could be inconsistent with the real
state.
2. When exiting from an X.Org session, the user could be unable to
type anything. The workaround was to switch to another console
window and come back.
Differential Revision: https://reviews.freebsd.org/D821
Reviewed by: ray@
Approved by: ray@
Tested by: kwm@
MFC after: 3 days
Also increase default for Tx queue get-list limit.
Too small limit results in TCP packets drops especiall when many
streams are running simultaneously.
Put list may be kept small enough since it is just a temporary
location if transmit function can't get Tx queue lock.
Submitted by: Andrew Rybchenko <arybchenko at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Required size of event queue is calculated now.
Submitted by: Andrew Rybchenko <arybchenko at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Remove trailing whitespaces and tabs.
Enclose value in return statements in parentheses.
Use tabs after #define.
Do not skip comparison with 0/NULL in boolean expressions.
Submitted by: Andrew Rybchenko <arybchenko at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Fix a problem where the blockback driver could run out of requests,
despite the fact that we allocate enough request and reqlist
structures to satisfy the maximum possible number of requests.
The problem was that we were sending responses back to the other
end (blockfront) before freeing resources. The Citrix Windows
driver is pretty agressive about queueing, and would queue more I/O
to us immediately after we sent responses to it. We would run into
a resource shortage and stall out I/O until we freed resources.
It isn't clear whether the request shortage condition was an
indirect cause of the I/O hangs we've been seeing between Windows
with the Citrix PV drivers and FreeBSD's blockback, but the above
problem is certainly a bug.
Sponsored by: Spectra Logic
Submitted by: ken
Reviewed by: royger
dev/xen/blkback/blkback.c:
- Break xbb_send_response() into two sub-functions,
xbb_queue_response() and xbb_push_responses().
Remove xbb_send_response(), because it is no longer
used.
- Adjust xbb_complete_reqlist() so that it calls the
two new functions, and holds the mutex around both
calls. The mutex insures that another context
can't come along and push responses before we've
freed our resources.
- Change xbb_release_reqlist() so that it requires
the mutex to be held instead of acquiring the mutex
itself. Both callers could easily hold the mutex
while calling it, and one really needs to hold the
mutex during the call.
- Add two new counters, accessible via sysctl
variables. The first one counts the number of
I/Os that are queued and waiting to be pushed
(reqs_queued_for_completion). The second one
(reqs_completed_with_error) counts the number of
requests we've completed with an error status.
Using realmem on PVH is not realiable, since in this case the realmem value
is computed from Maxmem, which contains the higher memory address found. Use
HYPERVISOR_start_info->nr_pages instead, which is set by the hypervisor and
contains the exact number of memory pages assigned to the domain.
Sponsored by: Citrix Systems R&D
This device is used by the user-space daemon that runs xenstore
(xenstored). It allows xenstored to map the xenstore memory page, and
reports the event channel xenstore is using.
Sponsored by: Citrix Systems R&D
dev/xen/xenstore/xenstored_dev.c:
- Add the xenstored character device that's used to map the xenstore
memory into user-space, and to report the event channel used by
xenstore.
conf/files:
- Add the device to the build process.
Convert the xenstore user-space device (/dev/xen/xenstore) to a device
using the newbus interface. This allows us to make the device
initialization dependant on the initialization of xenstore itself in
the kernel.
Sponsored by: Citrix Systems R&D
dev/xen/xenstore/xenstore.c:
- Convert to a newbus device, this removes the xs_dev_init function.
xen/xenstore/xenstore_internal.h:
- Remove xs_dev_init prototype.
dev/xen/xenstore/xenstore.c:
- Don't call xs_dev_init anymore, the device will attach itself when
xenstore is started.
The xenstore related devices in the kernel cannot be started until
xenstored is running, which will happen later in the Dom0 case. If
start_info_t doesn't contain a valid xenstore event channel, defer all
xenstore related devices attachment to later.
Sponsored by: Citrix Systems R&D
dev/xen/xenstore/xenstore.c:
- Prevent xenstore from trying to attach it's descendant devices if
xenstore is not initialized.
- Add a callback in the xenstore interrupt filter that will trigger
the plug of xenstore descendant devices on the first received
interrupt. This interrupt is generated when xenstored attaches to
the event channel, and serves as a notification that xenstored is
running.
Move xenstore related devices (xenstore.c and xenstore_dev.c) from
xen/xenstore to dev/xen/xenstore. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
This is done so we can prevent the Xen Balloon driver from attaching
before xenstore is setup.
Sponsored by: Citrix Systems R&D
dev/xen/balloon/balloon.c:
- Make xen balloon a driver that depends on xenstore.
This patch adds support for MSI interrupts when running on Xen. Apart
from adding the Xen related code needed in order to register MSI
interrupts this patch also makes the msi_init function a hook in
init_ops, so different MSI implementations can have different
initialization functions.
Sponsored by: Citrix Systems R&D
xen/interface/physdev.h:
- Add the MAP_PIRQ_TYPE_MULTI_MSI to map multi-vector MSI to the Xen
public interface.
x86/include/init.h:
- Add a hook for setting custom msi_init methods.
amd64/amd64/machdep.c:
i386/i386/machdep.c:
- Set the default msi_init hook to point to the native MSI
initialization method.
x86/xen/pv.c:
- Set the Xen MSI init hook when running as a Xen guest.
x86/x86/local_apic.c:
- Call the msi_init hook instead of directly calling msi_init.
xen/xen_intr.h:
x86/xen/xen_intr.c:
- Introduce support for registering/releasing MSI interrupts with
Xen.
- The MSI interrupts will use the same PIC as the IO APIC interrupts.
xen/xen_msi.h:
x86/xen/xen_msi.c:
- Introduce a Xen MSI implementation.
x86/xen/xen_nexus.c:
- Overwrite the default MSI hooks in the Xen Nexus to use the Xen MSI
implementation.
x86/xen/xen_pci.c:
- Introduce a Xen specific PCI bus that inherits from the ACPI PCI
bus and overwrites the native MSI methods.
- This is needed because when running under Xen the MSI messages used
to configure MSI interrupts on PCI devices are written by Xen
itself.
dev/acpica/acpi_pci.c:
- Lower the quality of the ACPI PCI bus so the newly introduced Xen
PCI bus can take over when needed.
conf/files.i386:
conf/files.amd64:
- Add the newly created files to the build process.
This switches code to using xpt_scan() routine, irrelevant to locking.
Using xpt_action() directly requires knowledge about higher level locks,
that SIM does not need to have.
This code is obsoleted, but that is not a reason to crash.
MFC after: 3 days
These variants have a few differences from the default AR9485 NIC,
namely:
* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.
To make this possible:
* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.
This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.
Tested:
* AR9380 (STA)
* AR9485 CUS198 (STA)
Obtained from: Qualcomm Atheros, Linux ath9k
In some code that is shared between the ixl(4) and ixlv(4) drivers,
a macro hard-coded a register offset that was not valid on ixlv devices.
Fix this by having each driver define a variable that contains the correct
offset.
Reviewed by: Eric Joyner <ricera10 AT gmail.com>
MFC after: 3 days
Sponsored by: Sandvine Inc
Previously it was possible for issues e.g. use after free, to result
from processing the done queue while not holding the channel lock.
While this should never happen in practice, unexpected code flows
which result in two threads processing from the same queue may
be possible.
We now use a local STAILQ to prevent this ever being an issue.
Sponsored by: Multiplay
Do not pass wrong alignment value to fwdma_malloc_multiseg and ultimately
to contigalloc. In addition to being wrong, this causes insta-panic in
certain cases due to safety assertion - the alignment is required to be
the power of two and the value we calculate here seldom is.
MFC after: 1 month
Commit my version of style(9) pass over the firewire code. Now that
other people have started changing the code carrying this is as a
local patch is not longer a viable option.
MFC after: 1 month
available before any uppper layer driver (TOE, iWARP, or iSCSI)
registers with the base cxgbe(4) driver.
Submitted by: Hariprasad at chelsio dot com
Reviewed by: np@
- Do not set if_collisions on interrupt, read them in ti_get_counter().
- Add missing bus_dmamap_sync(BUS_DMASYNC_PREREAD) in ti_ioctl2(). [1]
Submitted by: mav [1]
- Use bus_*() instead of bus_space_*().
- Use device_printf().
- Remove unused global variables and the extra warning suppression
they required.
- Use callout() instead of timeout().
Reviewed by: se
node's interrupts=<...> property creating resource list entries with a
single common implementation. This change makes ofw_bus_intr_to_rl() the
one true copy of that code and removes the copies of it from other places.
This also adds handling of the interrupts-extended property, which allows
specifying multiple interrupts for a node where each interrupt can have a
separate interrupt-parent. The bindings for this state that the property
cells contain an xref phandle to the interrupt parent followed by whatever
interrupt info that parent normally expects. This leads to having a
variable number of icells per interrupt in the property. For example you
could have <&intc1 1 &intc2 26 9 0 &intc3 9 4>.
Differential Revision: https://reviews.freebsd.org/D803
but taken from hardware.
- Mechanically convert to if_inc_counter() the rest of counters.
- While here fix 3 instances of the same bug, when error counter was ++
in one place and then assigned in other place, losing the increment.
Achieve that storing soft errors counters in softc.
that the driver is not going to be ever improved in terms of hardware
support, it is going to be only maintained as our kernel APIs change.
Carrying all the compatibility with ancient versions of NetBSD, OpenBSD,
Linux and BSDI, as well as obsoleted FreeBSD versions has no reason.
addresses. (The chip doesn't really care, it's just that it needs to be
told explicitly if unicast DMACs are checked for "hits" in the hash that
is used after the TCAM entries are all used up).
Summary:
Add the beginnings of multipass suspend/resume, by introducing
BUS_SUSPEND_CHILD/BUS_RESUME_CHILD, and move the PCI driver to this.
Reviewers: jhb
Reviewed By: jhb
Differential Revision: https://reviews.freebsd.org/D590
1. changed the code so that 2**16 keys are supported
2. changed the number of possible fans in a system from 2 to 6
3. added write support for some fan sysctls
4. added a new sysctl which shows the ID of the fan
5. added four more apple models with their temperature keys
6. changed the maxnumber of temperature keys from 36 to 80
7. replaced several fixed buf sizes to sizeof buf
Obtained from: Denis Ahrens denis at h3q.com
MFC after: 4 weeks
The current TSO limitation feature only takes the total number of
bytes in an mbuf chain into account and does not limit by the number
of mbufs in a chain. Some kinds of hardware is limited by two
factors. One is the fragment length and the second is the fragment
count. Both of these limits need to be taken into account when doing
TSO. Else some kinds of hardware might have to drop completely valid
mbuf chains because they cannot loaded into the given hardware's DMA
engine. The new way of doing TSO limitation has been made backwards
compatible as input from other FreeBSD developers and will use
defaults for values not set.
Reviewed by: adrian, rmacklem
Sponsored by: Mellanox Technologies
MFC after: 1 week
The original code was .. well, slightly more than incorrect.
It showed up as stalled RX queues if the NIC needed to be frequently
reinitialised (eg during scans.)
This is inspired by work done by Matt Dillon over at the DragonflyBSD
project.
So:
* track when EDMA RX has been stopped and when the MAC has been reset;
* re-initialise the ring only after a reset;
* track whether RX has been stopped/started - just for debugging now;
* don't bother with the RX EOL stuff for EDMA - we don't need the
interrupt at all. We also don't need to disable/enable the interrupt
or start DMA - once new frames are pushed into the ring via the
normal RX path, it'll just restart RX DMA on its own.
Tested:
* AR9380, STA mode
* AR9380, AP mode
* AR9485, STA mode
* AR9462, STA mode
It's now possible to scroll up the 500 hard-coded lines of history, not
just a fraction of them. For instance, one can reach the top of the boot
process.
Sometimes, when scrolling or when changing the screen size (by changing
the font or loading a KMS driver for instance), one could see the
history cycling (old content appeared below latest lines). This is
fixed.
Now, when the resolution changes are more lines can be shown, the
displayed area is adjusted so that, if the screen was filled with
content before, it's filled with content after as well: more history
is visible, instead of having blank lines below the previously visible
content.
MFC after: 3 days
struct ifnet if_oqdrops.
Some netgraph modules used ifqueue w/o ifnet. Accounting of queue drops
is simply removed from them. There were no API to read this statistic.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Rather than #define-ing common code function calls to OS-dependent
ones, make the osdep versions match the common code expectations,
adjust the FreeBSD specific code to use those, and remove the
#defines.
In the FreeBSD specific code, use "i40e_mem_reserved" for the
now expected but unused argument to i40e_allocate_dma_mem().
Reviewed by: gnn, eric.joyner intel.com
MFC after: 3 days
- Do not accumulate statistics on every tick.
- Accumulate statistics in vtnet_setup_stat_sysctl()
and in vtnet_get_counter().
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
double-free mbufs.
Like ixgbe(4) chipsets, EOP is only set on the final descriptor
in a chain of descriptors. So, to free the whole list of descriptors,
we should free the current slot _and_ the assembled list of descriptors
that make up the fragment list.
The existing code was setting discard once it saw EOP + an error status;
it then freed all the subsequent descriptors until the next EOP. That's
totally the wrong order.
- Do not ever set a counter to a value. For those counters
that we don't increment, but return directly from hardware
create cases in if_get_counter() method.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
with mbufs normally called *m in one place), rename the function
arguments to "mem".
This is a non-functional change.
Reviewed by: gnn, eric.joyner intel.com
MFC after: 3 days
In the current implementation, the isp_kthread() threads never exit.
The target threads do have an exit mode from isp_attach(), but it is
not invoked from isp_detach().
Ensure isp_detach() notifies threads started for each channel, such
that they exit before their parent device softc detaches, and thus
before the module does. Otherwise, a page fault panic occurs later in:
sysctl_kern_proc
sysctl_out_proc
kern_proc_out
fill_kinfo_proc
fill_kinfo_thread
strlcpy(kp->ki_wmesg, td->td_wmesg, sizeof(kp->ki_wmesg));
For isp_kthread() (and isp(4) target threads), td->td_wmesg references
now-unmapped memory after the module has been unloaded. These threads
are typically msleep()ing at the time of unload, but they could also
attempt to execute now-unmapped code segments.
MFC after: 1 month
Sponsored by: Spectra Logic
MFSpectraBSD: r1070921 on 2014/06/22 13:01:17
This feature is required by Mesa 9.2+. Without this, a GL application
crashes with the following message:
# glxinfo
name of display: :0.0
Gen6+ requires Kernel 3.6 or later.
Assertion failed: (ctx->Version > 0), function handle_first_current,
file ../../src/mesa/main/context.c, line 1498.
Abort (core dumped)
Now, Mesa 10.2.4 and 10.3-rc3 works fine:
# glxinfo
name of display: :0
display: :0 screen: 0
direct rendering: Yes
...
OpenGL renderer string: Mesa DRI Intel(R) 965GM
OpenGL version string: 2.1 Mesa 10.2.4
...
The code was imported from Linux 3.8.13.
Reviewed by: kib@
Tested by: kwm@, danfe@, Henry Hu,
Lundberg, Johannes <johannes@brilliantservice.co.jp>,
Johannes Dieterich <dieterich.joh@gmail.com>,
Lutz Bichler <lutz.bichler@gmail.com>,
MFC after: 3 days
Relnotes: yes
in r263741. At least with CTL (slightly modified to report SPC2) there
is still some problem: it doesn't seem to find LUNs higher than 7.
Sponsored by: The FreeBSD Foundation
commit 8bd88585ed8e3f7def0d780a1bc30d96fe642b9c
Rework atse_rx_cycles handling: count packets instead of fills, and use the
limit only when polling, not when in interrupt mode. Otherwise, we may
stop reading the FIFO midpacket and clear the event mask even though the
FIFO still has data to read, which could stall receive when a large packet
arrives. Add a comment about races in the Altera FIFO interface: we may
need to do a little more work to handle races than we are.
commit 20b39086cc612f8874dc9e6ef4c0c2eb777ba92a
Use 'sizeof(data)' rather than '4' when checking an mbuf bound, as is the
case for adjusting length/etc.
commit e18953174a265f40e9ba60d76af7d288927f5382
Break out atse_intr() into two separate routines, one for each of the two
interrupt sources: receive and transmit.
commit 6deedb43246ab3f9f597918361831fbab7fac4ce
For the RX interrupt, take interest only in ALMOSTEMPTY and OVERFLOW.
For the TX interrupt, take interest only in ALMOSTFULL and UNDERFLOW.
Perform TX atse_start_locked() once rather than twice in TX interrupt
handling -- and only if !FULL, rather than unconditionally.
commit 12601972ba08d4380201a74f5b967bdaeb23092c
Experimentation suggests that the Altera Triple-Speed Ethernet documentation
is incorrect and bits in the event and interrupt-enable registers are not
irrationally rearranged relative to the status register.
commit 3cff2ffad769289fce3a728152e7be09405385d8
Substantially rework interrupt handling in the atse(4) driver:
- Introduce a new macro ATSE_TX_PENDING() which checks whether there is
any pending data to transmit, either in an in-progress packet or in
the TX queue.
- Introduce new ATSE_RX_STATUS_READ() and ATSE_TX_STAUTS_WRITE() macros
that query the FIFO status registers rather than event registers,
offering level- rather than edge-triggered FIFO conditions.
- For RX, interrupt only on full/overflow/underflow; for TX, interrupt
only on empty/overflow/underflow.
- Add new ATSE_RX_INTR_READ() and ATSE_RX_INTR_WRITE() macros useful for
debugging interrupt behaviour.
- Add a debug.atse_intr_debug_enable sysctl that causes various pieces
of FIFO state to be printed out on each RX or TX interrupt. This is
disabled by default but good to turn on if the interface appears to
wedge. Also print debugging information when polling.
- In the watchdog handler, do receive, not just transmit, processing, to
ensure that the rx, not just tx, queue is being handled -- and, in
particular, will be drained such that interrupts can resume.
- Rework both atse_rx_intr() and atse_tx_intr() to eliminate many race
conditions, and add comments on why various things are in various
orders. Interactions between modifications to the event and interrupt
masks are quite subtle indeed, and we must actively check for a number
of races (e.g., event mask cleared; packet arrives; interrupts enabled).
We also now use the status registers rather than event registers for
FIFO status checks to avoid other races; we continue to use event
registers for underflow/overflow.
With this change, interrupt-driven operation of atse appears (for the
time being) robust.
commit 3393bbff5c68a4e61699f9b4a62af5d2a5f918f8
atse: Fix build after 3cff2ffa
Obtained from: cheribsd
Submitted by: rwatson, emaste
Sponsored by: DARPA/AFRL
MFC after: 3 days
fmp->buf at the free point is already part of the chain being freed,
so double-freeing is counter-productive.
Submitted by: Marc De La Gueronniere <mdelagueronniere@verisign.com>
MFC after: 1 week
Sponsored by: Verisign, Inc.
This allows the NIC to drop frames on the receive queue and not
cause the MAC to block on receiving to _any_ queue.
Tested:
igb0@pci0:5:0:0: class=0x020000 card=0x152115d9 chip=0x15218086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = 'I350 Gigabit Network Connection'
class = network
subclass = ethernet
Discussed with: Eric Joyner <eric.joyner@intel.com>
MFC after: 1 week
Sponsored by: Norse Corp, Inc.
spaces, rather than a split address, we actually can't check for being within
the kernel's address range. Instead, do what other backtraces do, and use
trapexit()/asttrapexit() as the stack sentinel.
MFC after: 3 weeks
The current TSO limitation feature only takes the total number of
bytes in an mbuf chain into account and does not limit by the number
of mbufs in a chain. Some kinds of hardware is limited by two
factors. One is the fragment length and the second is the fragment
count. Both of these limits need to be taken into account when doing
TSO. Else some kinds of hardware might have to drop completely valid
mbuf chains because they cannot loaded into the given hardware's DMA
engine. The new way of doing TSO limitation has been made backwards
compatible as input from other FreeBSD developers and will use
defaults for values not set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
many thanks for their continued support of FreeBSD.
While I'm there, also implement a new build knob, WITHOUT_HYPERV to
disable building and installing of the HyperV utilities when necessary.
The HyperV utilities are only built for i386 and amd64 targets.
This is a stable/10 candidate for inclusion with 10.1-RELEASE.
Submitted by: Wei Hu <weh microsoft com>
MFC after: 1 week
Huawei. It might appear as if the firmware is allocating memory blocks
according to the USB transfer size and if there is initially a lot of
data, like at the answering machine prompt, it simply dies without any
apparent reason. The simple workaround for this is to force a zero
length packet at hardware level after every 512 bytes of data. This
will force the other side to use smaller memory blocks aswell.
MFC after: 1 week
an mbuf's storage (internal or external).
Add a new M_SIZE() mbuf macro that returns the size of an mbuf's
storage (internal or external).
These contrast with m_data and m_len, which are with respect to data
in the buffer, rather than the buffer itself.
Rewrite M_LEADINGSPACE() and M_TRAILINGSPACE() in terms of M_START()
and M_SIZE().
This is done as we currently have many instances of using mbuf flags
to generate pointers or lengths for internal storage in header and
regular mbufs, as well as to external storage. Rather than replicate
this logic throughout the network stack, centralising the
implementation will make it easier for us to refine mbuf storage.
This should also help reduce bugs by limiting the amount of
mbuf-type-specific pointer arithmetic. Followup changes will
propagate use of the macros throughout the stack.
M_SIZE() conflicts with one macro in the Chelsio driver; rename that
macro in a slightly unsatisfying way to eliminate the collision.
MFC after: 3 days
Obtained from: jeff (with enhancements)
Sponsored by: EMC / Isilon Storage Division
Reviewed by: bz, glebius, np
Differential Revision: https://reviews.freebsd.org/D753
reboot/halt/debug.
o Add support for most key combinations supported by syscons(4).
Reviewed by: dumbbell, emaste (prev revision of D747)
MFC after: 5 days
Sponsored by: The FreeBSD Foundation
device drivers with calls to the centralised m_print() implementation.
While the formatting and output details differ a little, the content
is essentially the same, and it is unlikely anyone has used this
debugging output in some time.
This change reduces awareness of mbuf cluster allocation (and,
especially, the M_EXT flag) outside of the mbuf allocator, which will
make it easier to refine the external storage mechanism without
disrupting drivers in the future.
Style bugs are preserved.
Reviewed by: bz, glebius
MFC after: 3 days
Sponsored by: EMC / Isilon Storage Division
The nmdm code enforces a number between the 'nmdm' and 'A|B' portions
of the device name. This is then used as a unit number, and sprintf'd
back into the tty name. If leading zeros were used in the name,
the created device name is different than the string used for the
clone-open (e.g. /dev/nmdm0001A will result in /dev/nmdm1A).
Since unit numbers are no longer required with the updated tty
code, there seems to be no reason to force the string to be a
number. The fix is to allow an arbitrary string between
'nmdm' and 'A|B', within the constraints of devfs names. This allows
all existing user of numeric strings to continue to work, and also
allows more meaningful names to be used, such as bhyve VM names.
Tested on amd64, i386 and ppc64.
Reported by: Dave Smith
PR: 192281
Reviewed by: neel, glebius
Phabric: D729
MFC after: 3 days
This fixes a bug where scroll lock would not work for tty #0 when using
vt_vga's textmode. The reason was that this window is created with a
static 256x100 buffer, larger than the real size of 80x25.
Now, in vt_change_font() and vt_compute_drawable_area(), we still
perform operations even of the window has no font loaded (this is the
case in textmode here vw->vw_font == NULL). One of these operation
resizes the buffer accordingly.
In vt_compute_drawable_area(), we take the terminal size as is (ie.
80x25) for the drawable area.
The font argument to vt_set_border() is removed (it was never used) and
the code now uses the computed drawable area instead of re-doing its own
calculation.
Reported by: Harald Schmalzbauer <h.schmalzbauer_omnilan.de>
Tested by: Harald Schmalzbauer <h.schmalzbauer_omnilan.de>
MFC after: 3 days
The rules turn out to be:
* for non-aggregation session TX queues - it's either sent or not sent.
* for aggregation session TX queues - if nframes=1, then the status reflects
the completed transmission.
* however, for nframes > 1, then this is just a status reflecting what
the initial transmission did. The compressed BA (immediate or delayed)
may not have yet been received, so the actual frame status is in the
compressed BA updates.
Whilst here, I fiddled with debugging and formatting a bit.
There's also RTS attempts (what the atheros chips call "short retries")
which weren't being logged and they aren't yet being used in the rate
control statistics updates. For now, at least log them.
TODO:
* This still isn't 100% correct! So I have to tinker with this some more.
(The failures aren't always failures..)
* Extend the rate control API in net80211 so it can take both short and
long retry counts.
Tested:
* Intel 5100, STA mode
The (eventual) intention is to create MIB counters for transmitted
frame completion to count how many packets with each status are
transmitted.
Note the difference between A-MPDU and non A-MPDU status.
Obtained from: Linux iwlwifi/dvm driver
For controllers with only one port (like PCIe or M.2 SSDs) interrupt can
come from only one source, and skipping read saves few percents of CPU time.
MFC after: 1 month
H/W donated by: I/O Switch
an entry in the xref list if one doesn't already exist for the given handle.
On a system that uses phandle properties, the init-time scan of the tree
which builds the xref list will pre-create entries for every xref handle
that exists in the data. On systems where the xref and node handles are
synonymous there is no phandle property in referenced nodes, and the xref
list will initialize to an empty state. In the latter case, we still need
to be able to associate a device_t with an xref handle, so we create list
entries on the fly as needed. Since the node and xref handles are
synonymous, we have all the info needed to create a list entry at device
registration time.
The downside to this change is that it basically allows on the fly creation
of xref handles as synonyms of node handles, and the association of a
device_t with them. Whether this is a bug or a feature is in the eye of
the beholder, I guess.
resume that is a superset of a pcb. Move the FPU state out of the pcb and
into this new structure. As part of this, move the FPU resume code on
amd64 into a C function. This allows resumectx() to still operate only on
a pcb and more closely mirrors the i386 code.
Reviewed by: kib (earlier version)
for the node. The default routine returns the untranslated handle, which
is sometimes useful, but sometimes you really need to know there's no
entry in the xref<->node<->device translation table.
I gave up to update list of Marvell chips that require this quirk.
The final nail was growing number of PCIe/M.2 SSDs where Marvell chips
have PCI IDs of different vendors.
MFC after: 1 week
H/W donated by: I/O Switch
PCI IDs into quirks, which mostly fit (though you'd get no argument
from me that AHCI_Q_SATA1_UNIT0 is oddly specific). Set these quirks
in the PCI attachment. Make some shared functions public so that PCI
and possibly other bus attachments can use them.
The split isn't perfect yet, but it is functional. The split will be
perfected as other bus attachments for AHCI are written.
Sponsored by: Netflix
Reviewed by: kan, mav
Differential Revision: https://reviews.freebsd.org/D699
Current busdma code for unmapped bios will not properly align the segment
size, causing corruption on blkfront devices. Revert the commit until
busdma code is fixed.
Reported by: mav
MFC after: 1 day
- miibus fixes as suggested by Yonghyeon Pyun.
- enable VLAN MTU support.
- fix a few WITNESS complaints in cgem_attach().
- have cgem_attach() properly init the ifnet struct before calling
mii_attach() to fix panic when using e1000phy.
- fix ethernet address changing.
- fix transmit queue overflow handling.
- tweak receive queue handling to reduce receive overflows.
- bring out MAC statistic counters to sysctls.
- add e1000phy to config file.
- implement receive hang work-around described in reference guide.
- change device name from if_cgem to cgem to be consistent with other
interfaces.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
Reviewed by: wkoszek, Yonghyeon PYUN <pyunyh@gmail.com>
This happen when converting any JBOD to RAID or creating
any new RAID from Unconfigured Drives.
Without this fix, user may see below call trace if WITNESS is enabled.
witness_warn() at witness_warn+0x4b5/frame 0xfffffe011f929a00
uma_zalloc_arg() at uma_zalloc_arg+0x3b/frame 0xfffffe011f929a70
malloc() at malloc+0x192/frame 0xfffffe011f929ac0
mrsas_bus_scan_sim() at mrsas_bus_scan_sim+0x32/frame 0xfffffe011f929af0
mrsas_aen_handler() at mrsas_aen_handler+0x11c/frame 0xfffffe011f929b20
taskqueue_run_locked() at taskqueue_run_locked+0xf0/frame 0xfffffe011f929b80
taskqueue_thread_loop() at taskqueue_thread_loop+0x9b/frame 0xfffffe011f929bb0
fork_exit() at fork_exit+0x84/frame 0xfffffe011f929bf0
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe011f929bf0
Submitted by: kadesai
Reviewed by: ambrisko
MFC after: 3 days
in the clocks=<...> properties of their FDT data. The clock properties
consist of 2-cell tuples, each containing a clock device node reference and
a clock number. A clock device driver can register itself as providing
this interface, then other drivers can turn the FDT clock node reference
into the corresponding device_t so that they can use the interface to query
and manipulate their clocks.
This provides convenience functions to enable or disable all the clocks
listed in the properties for a device, so most drivers will be able to
manage their clocks with a single call to fdt_clock_enable_all(dev).
xref handle, and for registering that association. Also use the same data
for faster translations between node and xref handles.
Now when fdt properties contain &othernode references, a driver can find
the device instance that corresponds to &othernode, and thus can use
interfaces provided by that instance.
Reviewed by: nwhitehorn
- Static'ize sdhci_debug local to sdhci.c.
- Const'ify PCI device description strings.
- Nuke redundant resource ID members from sdhci_pci_softc.
- Nuke unused hw.sdhci_pci.debug tunable.
- Add support for using MSI instead of INTx, controllable via the tunable
hw.sdhci.enable_msi (defaulting to on) and tested with a RICOH R5CE823 SD
controller.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
and keep both converted to drvapi and non-converted drivers
compilable.
o Make if_t typedef to struct ifnet *.
o Remove shim functions.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
initializing 16. Initialize all 20 so we don't send garbage in the
Auxiliary register. The SATA standard mandates a 5 dword length for
the Host to Device FIS.
Sponsored by: Netflix
announce the change on the vap's ifnet instead of the main ifnet. This
matches the behavior of other wireless drivers in the tree and allows the
default devd configuration to correctly start dhclient automatically after
an ndis wireless device associates.
MFC after: 2 weeks
* Convert ixgbe to use this ioctl
* Convert ifconfig to use generic i2c handler for "ix" interfaces.
Approved by: Eric Joyner (ixgbe part)
MFC after: 2 weeks
Sponsored by: Yandex LLC
extension. Provide prototypes for the actual implementations.
Correct function arguments to match the implementations.
MFC after: 3 days
X-MFC with: r270755
and code to make the code compile.
Give the function seems to be slightly mixed with csum and tso,
make it non-fatal if we try to setup thing on a kernel without IP
support. In practise the printf on the console will probably still
make your machine unhappy.
MFC after: 3 days
X-MFC with: r270755
In general theraven is right that we should factr this out and provide
a general and per-arch implementation that everything can use.
MFC after: 3 days
X-MFC with: r270755
- use proper __FreeBSD_version check and more importantly check for __am64__
to be defined. Whether the FreeBSD(_version) checks are needed is a
different question.
- cast uint64_t to uintmax_t and use %jx for printing.
Note: there are more values that could be printed in that status function
but leave that for the future; printf doesn't seem to be the right
way to do it anyway.
Note: there is more breakage related to i40e_allocate_dma*() having
conflicting declarations, so more fixes to come.
PR: 193112
MFC after: 3 days
X-MFC with: r270755
Fix missing includes and invalid vars in ixl / ixlv driver added by r270346
which caused build failures for GENERIC kernel after it was made default
by r270755.
X-MFC-With: r270346 / r270755
Sponsored by: Multiplay
but has some retries.
Without this, single frame transmission in AMPDU will always look like
it succeeded fine, and thus AMRR will think it's totally fine to just
keep upping the rate upwards.
Now, this is still not quite right! For multi-frame aggregates the
completion happens in two parts - the TX done and the BA received.
The driver is currently double accounting those a little - there's no
way to say to the rate control code "I completed X frames, Y worked fine,
there were Z retries." And it's a bit odd with iwn, as the firmware
retransmits frames for us so we don't get to see how many retransmits
happened; only that it took longer than normal. I may have to extend
the rate control API to properly track that.
So this may keep the rate lower than it should be, but that's better
than keeping it higher than it should be.
Tested:
* 5100, STA mode
in preparation for the 5300 3x3 NIC.
During this particular adventure, I did indeed discover that a whole
swath of things made little to no sense.
Those included, and are fixed here:
* A lot of the antenna configuration bits assume the NIC has two receive
chains. That's blatantly untrue for NICs that don't.
* There was some disconnect between the antenna configuration when
forming a PLCP rate DWORD (which includes the transmit antenna
configuration), separate to the link quality antenna configuration.
So now there's helper functions to return which antenna configurations
to use and those are used wherever an antenna config is required.
* The 5300 does up to three stream TX/RX (so MCS0->23), however
the link quality table has only 16 slots. This means all of the
rate entries are .. well, dual-stream rates. If this is the case,
the "last MIMO" parameter can't be 16 or it panics the firmware.
Set it to 15.
* .. and since yes it has 16 slots, it only would try retransmitting
from MCS8->MCS23, which can be quite .. terrible. Hard-code the last
two retry slots to be the lowest configured rate.
* I noticed some transmit configuration command stuff is different
based on firmware API version, so I lifted that code from Linux.
* Add / augment some more logging to make it easier to capture this
stuff.
Now, 3x3 is still terrible because the link quality configuration is
plainly not good enough. I'll have to think about that.
However, the original goal of this - 3x3 operation on the Intel
5300 NIC - actually worked.
There are also rate control bugs in the way this driver handles
notifying the net80211 rate control code when AMPDU is enabled.
It always steps the rate up to the maximum rate possible - and
this eventually ends in much sadness. I'll fix that later.
As a side note - 2GHz HT40 now works on all the NICs I have tested.
As a second side note - this exposed some bad 3x3 behaviour in
the ath(4) rate control code where it starts off at a 3-stream rate
and doesn't downgrade quickly enough. This makes the initial
dhcp exchange take a long time. I'll fix the ath(4) rate code
to start at a low fixed 1x1 MCS rate and step up if everything
works out.
Tested:
* Intel 2200
* Intel 2230
* Intel 5300
* Intel 5100
* Intel 6205
* Intel 100
TODO:
* Test the other NICs more thoroughly!
Thank you to Michael Kosarev <russiane39@gmail.com> for donating the
Intel 5300 NIC and pestering me about it since last year to try and
make it all work.
There were two issues:
1. The area given to vt_is_cursor_in_area() was adding the drawable
area offset, something already handled by this function.
2. The cursor was shifted on the screen by the offset of this area
and thus was misplaced or not erased. Furthermore, when reaching
the bottom or right borders, the cursor was either totally
removed or not erased correctly.
MFC after: 1 week
hardware driver update from Mellanox Technologies.
- Remove empty files from the OFED Linux Emulation layer.
- Fix compile warnings related to printf() and the "%lld" and "%llx"
format specifiers.
- Add some missing 2-clause BSD copyrights.
- Add "Mellanox Technologies, Ltd." to list of copyright holders.
- Add some new compatibility files.
- Fix order of uninit in the mlx4ib module to avoid crash at unload
using the new module_exit_order() function.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The timer is restarted whenever a window buffer is marked as dirty or
the mouse cursor moves.
There's still room for improvement. For instance, we should not mark a
window buffer as dirty when this window isn't displayed.
Review: https://reviews.freebsd.org/D683
Reviewed by: ray@
Approved by: ray@
MFC after: 1 week
If DDB is active, we can't use a taskqueue thread to switch away from
the X window, because this thread can't run.
Reviewed by: ray@
Approved by: ray@
MFC after: 1 week
They are used when a panic occurs or when entering a DDB session for
instance.
cngrab() forces a vt-switch to the console window, no matter if the
original window is another terminal or an X session. However, cnungrab()
doesn't vt-switch back to the original window currently.
MFC after: 1 week
With the current implementation, this allows an X11 server to tell
the console it switches a particular window in "graphics mode". This
information is used by the mouse handling code to ignore sysmouse events
in the window taken by the X server: only him should receive those
events.
Reported by: flo@, glebius@, kan@
Tested by: flo@
Reviewed by: kan@
MFC after: 1 week
... not just the visible part.
This fixes a bug where, when switching from eg. vt_vga to vt_fb (ie. the
resolution goes up), the originally hidden, uninitialized area of the
buffer is displayed on the screen. This leads to a missing text cursor
when it's over an unitialized area.
This was also visible when selecting text: the uninitialized area was
not highlighted.
Internally, this area was zeroed: characters were all 0x00000000,
meaning the foreground and background color was black. Now, everything
is filled with a space with a gray foreground color, like the visible
area.
While here, remove the check for the mute flag and always use
TERMINAL_NORM_ATTR as the character attribute (ie. gray foreground,
black background).
MFC after: 1 week
This allows backends to verify they do not draw outside of this area.
This fixes a bug in vt_vga where the text was happily drawn over the
right and bottom margins, when using the Gallant font.
MFC after: 1 week
... not the whole screen. Don't use font offsets in
vt_mark_mouse_position_as_dirty().
This fixes a bug where the mouse position wasn't marked as dirty when
approaching the borders of the drawn area.
MFC after: 1 week
This fixes a "General protection fault" in vt_vga, where
vt_is_cursor_in_area() erroneously reported that the cursor was over the
text. This led to negative integers stored in "unsigned int" and chaos.
MFC after: 1 week
add opregion handling for drm2 - which exposes some ACPI video configuration
pieces that some Lenovo laptop models use to flesh out which video device
to speak to. This enables the brightness control in ACPI to work these models.
The CADL bits are also important - it's used to figure out which ACPI
events to hook the brightness buttons into. It doesn't yet seem to work
for me, but it does for the OP.
Tested:
* Lenovo X230 (mine)
* OP: ASUS UX51VZ
PR: 190186
Submitted by: Henry Hu <henry.hu.sh@gmail.com>
Reviewed by: dumbbell
It's replaced by vd_bitblt_text_t, which gives more context to the
backend and allows it to perform more efficiently when redrawing a given
area.
MFC after: 1 week
to get upset.
The Qualcomm Atheros reference design code goes through significant
hacks to shut down RX before TX. It doesn't even try do do it in the
driver - it actually makes the DMA stop routines in the HAL shut down
RX before shutting down TX.
So, to make this work for chips that aren't the AR9380 and later, do
it in the driver. Shuffle the TX stop/drain HAL calls to be called
*after* the RX stop HAL call.
Tested:
* AR5413 (STA)
* AR5212 (STA)
* AR5416 (STA)
* AR9380 (STA)
* AR9331 (AP)
* AR9341 (AP)
TODO:
* test ar92xx series NIC and the AR5210/AR5211, in case there's something
even odder about those.
There were situations where the cursor was not erased/redrawn or its
position was marked as dirty even though it's not displayed. The code is
now more straightforward.
At the same, add a function to determine if the cursor covers a given
area. This is used by backends to know if they need to draw the cursor.
This new function should be paired with a new state in struct vt_device,
called vd_mshown, which indicates if the cursor should be displayed.
This again simplifies vd_bitblt_text_t callback's API.
MFC after: 1 week
In textmode, no font is loaded, thus the page fault in
vt_mark_mouse_position_as_dirty() when it wants the font width/height.
For now, create a fake area for the textmode. This needs to be modified
if vt_vga gains mouse support in textmode.
While here, fix a build failure when SC_NO_CUTPASTE is defined:
vt_mark_mouse_position_as_dirty() must not be included in this case.
MFC after: 1 week
This fixes a bug where vga_get_cp437() was called with an invalid
argument. The screen was then filled with '?' instead of the actual
character.
MFC after: 1 week
v1.0.1 2014-8-19
* Do not retry the command and reset the disk when failed to enable or
disable spin up feature.
* Fix up a bug that disk failed to probe if driver failed to access the
10th LBA.
* Fix a bug that request timeout but it has been completed in certain
cases.
* Support smartmontool for R750.
Many thanks to HighPoint for continued support of FreeBSD!
MFC after: 3 days
- It was decided to change the driver name to if_ixl for FreeBSD
- This release adds the VF Driver to the tree, it can be built into
the kernel or as the if_ixlv module
- The VF driver is independent for the first time, this will be
desireable when full SRIOV capability is added to the OS.
- Thanks to my new coworker Eric Joyner for his superb work in
both the core and vf driver code.
Enjoy everyone!
Submitted by: jack.vogel@intel.com and eric.joyner@intel.com
MFC after: 3 days (hoping to make 10.1)
After some testing, it appears that acquiring the lock once and keeping
it longer is slower than taking it multiple times.
While here, fix a typo in another comment.
MFC after: 1 week
Fix some frees incorrectly assigned to M_XENBUS when the memory is
allocated with M_XENSTORE.
Sponsored by: Citrix Systems R&D
MFC after: 1 week
dev/xen/blkback/blkback.c:
- Fix incorrect frees.
The previous global offset, based on the last loaded font, had no
meaning for other windows. This caused a shifted text area, often partly
out-of-screen.
MFC after: 1 week
This patch contains the following fixes for netback:
- Only unbind the evtchn if it has been bound.
- Set xnb->bridge to NULL after free to prevent double-freeing it.
- Set the MAC address for the host-facing interface to a dummy value.
Sponsored by: Citrix Systems R&D
dev/xen/netback/netback.c:
- Prevent trying to unbind if the evtchn has not been bounded.
- Prevent double-freeing xnb->bridge.
- Set the MAC address of the host-facing interface to a dummy value,
so it can work when the interface is added to a bridge.
This is needed so when running under Xen the calls to pci_child_added
can be intercepted and a custom Xen method can be used to register
those devices with Xen. This should not include any functional
change, since the Xen implementation will be added in a following
patch and the native implementation is a noop.
Sponsored by: Citrix Systems R&D
Reviewed by: jhb
dev/pci/pci.c:
dev/pci/pci_if.m:
dev/pci/pci_private.h:
dev/pci/pcivar.h:
- Add the pci_child_added newbus method.
This fixes a bug when two windows use different fonts, but a longer-term
solution is required. The dirty area should be stored as pixels, not
character cells, because such coordinates don't have the same meaning in
all windows, when using different fonts.
MFC after: 1 week
Compared to the deprecated vd_bitbltchr_t callback, vd_bitblt_text_t
receives:
o the whole text buffer
o the dirty area
o the mouse cursor (map, position, colors)
This allows the backend to perform optimization on how to draw things.
The goal is to remove vd_bitbltchr_t and vd_putchar_t, once all driver
are converted (only vt_vga is included in this commit).
In vt_vga, this allows to draw the text and the cursor in one pass,
without ever reading from video memory (because it has all the context).
The main benefit is the speed improvement: no more slideshow during
boot!
Other bugs fixed in vt_vga are:
o left-most characters are drawn properly (the left-most pixels were
missing with bold characters and some wide letters such as 'm')
o no more black square around the cursor
o no cursor flickering when the text is scrolling
There are still many problems to fix: the known issues are marked with
"FIXME" inside the code.
MFC after: 1 week
The goal is to clear the video memory, in case an application drew to
it. So the content shouldn't be loaded in the latches, it can't be
trusted anyway.
This improves a bit the window switch speed.
MFC after: 1 week
At the same time, "w" and "h" members are now called "width" and
"height". The goal is to have a more "public" structure, because it will
soon be passed as argument to a new callback, replacing vd_bitbltchr_t.
MFC after: 1 week
Later, we just see if the "struct mouse_cursor" pointer is set. This
avoids the need to mess with all the conditions several times; this has
been error prone.
While here, rename the variable "m" to a more meaningful "cursor", like
it's done elsewhere in the code.
MFC after: 1 week
This fixes bad looking refresh when switching window: squares instead
of text, flashing screen, and so on. In the worst case, vt_flush() came
at a very inappropriate timing and the screen was not refreshed at all
(leaving squares all over the place).
This doesn't fix the flickering of the screen with vt_vga, because the
sync signal is temporarily stopped and the video memory is cleared.
MFC after: 1 week
Like r270273, this has no effect for now, because the cursor is always
drawn. This is in preparation of future changes to vd_bitbltchr_t API.
MFC after: 1 week
Currently, this has no effect, because the cursor is always redrawn
anyway. But this will be useful after improvements to the vd_bitbltchr_t
callback API.
The vt_device structure members used to store the position of the cursor
as of the last redraw are renamed from vd_mdirty{x,y} to vd_mold{x,y}.
The associated comment is fixed too. Also, their value is now expressed
in pixels, not in character columns/row.
MFC after: 1 week
This avoids unnecessary redraw. In particular, during boot, where the
cursor is disabled and its fake position is [0;0], this triggered a
refresh of the whole screen each time vt_flush() is called.
MFC after: 1 week
Before the global flag was set/unset using the CONS_MOUSECTL ioctl, and
the per-window flag through the MOUSE_SETLEVEL or MOUSE_SETMODE ioctls.
Also, if the cursor is already enabled/disabled, return immediatly. This
avoids to reset the cursor's position to the center of the screen.
This matches syscons' behavior.
While here, remove a trailing space and a redundant variable
declaration.
Make the functions pci_disable_msi, pci_enable_msi and pci_enable_msix
methods of the newbus PCI bus. This code should not include any
functional change.
Sponsored by: Citrix Systems R&D
Reviewed by: imp, jhb
Differential Revision: https://reviews.freebsd.org/D354
dev/pci/pci.c:
- Convert the mentioned functions to newbus methods.
- Fix the callers of the converted functions.
sys/dev/pci/pci_private.h:
dev/pci/pci_if.m:
- Declare the new methods.
dev/pci/pcivar.h:
- Add helpers to call the newbus methods.
ofed/include/linux/pci.h:
- Add define to prevent the ofed version of pci_enable_msix from
clashing with the FreeBSD native version.
sample size. According to the USB audio frame format specification
from USB.org, the value in the "bBitResolution" field can be less than
the actual sample size, depending on the actual hardware, and should
not be used for this computation.
PR: 192755
MFC after: 1 week
Mostly bugfixes or features developed in the past 6 months,
so this is a 10.1 candidate.
Basically no user API changes (some bugfixes in sys/net/netmap_user.h).
In detail:
1. netmap support for virtio-net, including in netmap mode.
Under bhyve and with a netmap backend [2] we reach over 1Mpps
with standard APIs (e.g. libpcap), and 5-8 Mpps in netmap mode.
2. (kernel) add support for multiple memory allocators, so we can
better partition physical and virtual interfaces giving access
to separate users. The most visible effect is one additional
argument to the various kernel functions to compute buffer
addresses. All netmap-supported drivers are affected, but changes
are mechanical and trivial
3. (kernel) simplify the prototype for *txsync() and *rxsync()
driver methods. All netmap drivers affected, changes mostly mechanical.
4. add support for netmap-monitor ports. Think of it as a mirroring
port on a physical switch: a netmap monitor port replicates traffic
present on the main port. Restrictions apply. Drive carefully.
5. if_lem.c: support for various paravirtualization features,
experimental and disabled by default.
Most of these are described in our ANCS'13 paper [1].
Paravirtualized support in netmap mode is new, and beats the
numbers in the paper by a large factor (under qemu-kvm,
we measured gues-host throughput up to 10-12 Mpps).
A lot of refactoring and additional documentation in the files
in sys/dev/netmap, but apart from #2 and #3 above, almost nothing
of this stuff is visible to other kernel parts.
Example programs in tools/tools/netmap have been updated with bugfixes
and to support more of the existing features.
This is meant to go into 10.1 so we plan an MFC before the Aug.22 deadline.
A lot of this code has been contributed by my colleagues at UNIPI,
including Giuseppe Lettieri, Vincenzo Maffione, Stefano Garzarella.
MFC after: 3 days.
Using unmapped IO is really beneficial when running inside of a VM,
since it avoids IPIs to other vCPUs in order to invalidate the
mappings.
This patch adds unmapped IO support to blkfront. The following tests
results have been obtained when running on a Xen host without HAP:
PVHVM
3165.84 real 6354.17 user 4483.32 sys
PVHVM with unmapped IO
2099.46 real 4624.52 user 2967.38 sys
This is because when running using shadow page tables TLB flushes and
range invalidations are much more expensive, so using unmapped IO
provides a very important performance boost.
Sponsored by: Citrix Systems R&D
Tested by: robak
MFC after: 1 week
PR: 191173
dev/xen/blkfront/blkfront.c:
- Add and announce support for unmapped IO.
Rename vt_generate_vga_palette() to vt_generate_cons_palette() and
change it to build a palette where the color index is the same than in
terminal escape codes, not the VGA index. That's what TCHAR_CREATE()
uses and passes to vt(4).
The main differences between both orders are:
o Blue and red are swapped (1 <-> 4)
o Yellow and cyan are swapped (3 <-> 6)
The problem remained unnoticed, because the RGB bit indexes passed to
vt_generate_vga_palette() were reversed. This inversion was cancelled
by the colors inversions in the generated palette. For instance, red
(0xff0000) and blue (0x0000ff) have bytes in opposite order, but were
swapped in the palette. But after changing the value of blue (see last
paragraph), the modified color was in fact the red one.
This commit includes a fix to creator_vt.c, submitted by Nathan
Whitehorn: fb_cmsize is set to 16. Before this, the generated palette
would be overwritte. This fixes colors on sparc64 with a Creator3D
adapter.
While here, tune the palette to better match console colors and improve
the readability (especially the dark blue).
Submitted by: nwhitehorn (fix to creator_vt.c)
MFC after: 1 week
In several functions, vtbuf_putchar() in particular, the lock on vtbuf
is acquired twice:
1. once by the said functions;
2. once in vtbuf_dirty().
Now, vtbuf_dirty_locked() and vtbuf_dirty_cell_locked() allow to
acquire that lock only once.
This improves the input speed of vt(4). To measure the gain, a
50,000-lines file was displayed on the console using cat(1). The time
taken by cat(1) is reported below:
o On amd64, with vt_vga:
- before: 1.0"
- after: 0.5"
o On sparc64, with creator_vt:
- before: 13.6"
- after: 10.5"
MFC after: 1 week
vt_fb_attach() currently always returns 0, but it could return a code
defined in errno.h. However, it doesn't return a CN_* code. So checking
its return value against CN_DEAD (which is 0) is incorrect, and in this
case, a success becomes a failure.
The consequence was unimportant, because the caller (drm_fb_helper.c)
would only log an error message in this case. The console would still
work.
Approved by: nwhitehorn
The AR9380 and later chips have a 128KiB register window, so the register
read diag api needs changing.
The tools are about to be updated as well. No, they're not backwards
compatible.
the right register bank for the framebuffer. Disable the assigned-addresses
path on SPARC since it is just a hack for IBM PPC systems and was neither
relevant for nor worked on SPARC anyway.
vm_phys_fictitious_to_vm_page should not be called directly, even when
operating on a range that has been registered using
vm_phys_fictitious_reg_range. PHYS_TO_VM_PAGE should be used instead
because on arches that use VM_PHYSSEG_DENSE the page might come
directly from vm_page_array.
Reported by: nwhitehorn
Tested by: nwhitehorn, David Mackay <davidm.jx8p@gmail.com>
Sponsored by: Citrix Systems R&D
- Replace the global driver lock with a per-instance device lock.
- Use the per-instance device lock instead of Giant for the CAM sim lock.
- Add global locks to protect the adapter list and DPC queues.
- Use wakeup() and mtx_sleep() to wait for certain events like the
controller going idle rather than polling via timeouts passed to
tsleep().
- Use callout(9) instead of timeout(9).
- Mark the interrupt handler MPSAFE.
- Remove compat shims for FreeBSD versions older than 8.0.
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
- Use the existing vbus locks instead of Giant for the CAM sim lock.
- Use callout(9) instead of timeout(9).
- Mark the interrupt handler MPSAFE.
- Don't attempt to pass data in the softc from probe() to attach().
- Remove compat shims for FreeBSD versions older than 8.0.
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
- Use the existing vbus locks instead of Giant for the CAM sim lock.
- Use callout(9) instead of timeout(9).
- Mark the interrupt handler MPSAFE.
- Don't attempt to pass data in the softc from probe() to attach().
- Remove compat shims for FreeBSD versions older than 8.0.
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
- Use callout(9) instead of timeout(9).
- Use the existing hba lock as the CAM sim lock instead of Giant.
- Mark interrupt handler MPSAFE.
- Reorder detach and destroy the hba lock in detach.
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
- Cleanup some register reads and writes to use existing register
access macros.
- Ensure code which only applies to the control endpoint is not run
for other endpoints in the data transfer path.
MFC after: 3 days
handled by creator(4) (Sun Creator 3D, Elite 3D, etc.). This provides
vt(4) consoles on all devices currently supported by syscons on sparc64.
The driver should also be easily adaptable to support newer Sun framebuffers
such as the XVR-500 and higher.
Many thanks to dumbbell@ (Jean-Sebastien Pedron) for testing this remotely
during development.
ethernet class.
Note: This is untested as I do not have a device like this. That is
reflected in the MFC timeout.
PR: 192345
Submitted by: rozhuk.im gmail.com
MFC after: 4 weeks
Also disable a couple of ACPI devices that are not usable under Dom0.
To this end a couple of booleans are added that allow disabling ACPI
specific devices.
Sponsored by: Citrix Systems R&D
Reviewed by: jhb
x86/xen/xen_nexus.c:
- Return BUS_PROBE_SPECIFIC in the Xen Nexus attachement routine to
force the usage of the Xen Nexus.
- Attach the ACPI bus when running as Dom0.
dev/acpica/acpi_cpu.c:
dev/acpica/acpi_hpet.c:
dev/acpica/acpi_timer.c
- Add a variable that gates the addition of the devices.
x86/include/init.h:
- Declare variables that control the attachment of ACPI cpu, hpet and
timer devices.
Minor fixes to make the Xen Dom0 console work. This includes always
returning there's pending input in xencons_has_input, because on Dom0
there's no shared ring and we cannot test the indexes. The second
fix is to use the CONSOLEIO_read hypercall in order to read input
data from the Xen console.
Sponsored by: Citrix Systems R&D
dev/xen/console/xencons_ring.c:
- Always return true in xencons_has_input for Dom0.
- Implement Dom0 console support for xencons_handle_input.
bridges in strange ways, either rendering them unable to detect
insertion and removal events, or possibly unable to read from the
device behind the bridge.
This fixes at least one laptop, a Toshiba Tecra M5 with a Texas
Instruments PCxx12 (d=0x8039 v=0c104c) bridge. The very similar
Tecra M9 has the same bridge, but worked fine without this change.
The bridge chip has no I/O port BAR, and there is nothing in the spec
to suggest I/O decoding should be enabled; however enabling it fixes
the issue. Add an XXX comment to this effect.
Discussed with: jhb, imp
MFC after: 2 weeks
Reorganize struct sge_iq. Make the iq entry size a compile time
constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly.
MFC after: 2 weeks
In the mmcsd layer use this value to populate disk->d_ident. Also set
disk->d_descr to the full set of card identification info (includes vendor,
model, manufacturing date, etc).
* Implements Start Stop Unit for SATA direct-attach devices in IR mode to avoid
data corruption.
* Use CAM_DEV_NOT_THERE instead of CAM_SEL_TIMEOUT and CAM_TID_INVALID
Obtained from: LSI
MFC after: 2 weeks
framebuffer drivers. This lets ofwfb work with xf86-video-scfb and makes
the driver much more generic and less PCI-centric. This changes some
user-visible behavior and will require updates to the xorg-server port
on PowerPC when using ATI graphics cards.
doesn't have support for the Z8530. Embedded PowerPC platforms
typically don't. Fail when the device class we actually need is
not present.
Obtained from: Juniper Networks, Inc.
(I'm committing this on behalf of my colleagues in the Storage team
at Chelsio).
Submitted by: Sreenivasa Honnur <shonnur at chelsio dot com>
Sponsored by: Chelsio Communications.
custom free routine (rxb_free) in the driver. Fail MOD_UNLOAD with
EBUSY if any such cluster has been handed up to the kernel but hasn't
been freed yet. This prevents a panic later when the cluster finally
needs to be freed but rxb_free is gone from the kernel.
MFC after: 1 week
This change is a bit ugly, but so is the coupling between the i915
driver and syscons. It isn't worth developing a more elegant solution
only to support the legacy syscons console.
If RSS is enabled, ixgbe(4) will query the RSS API for the types of hashes
which should be used. It'll then only enable hashes that are exposed via
the RSS layer.
This way it won't try to do things like enable UDP hashing if RSS explicitly
states that it isn't supported in lookups.
Tested:
* 82599EB ixgbe(4) NIC
A mix of fragmented and non-fragmented UDP in a single stream will end up
being hashed differently, resulting in out-of-order behaviour in the receive
path.
This was done in the linux e1000 driver in 2011.
Discussed with: jfv
systems without either a CSM or real graphics drivers, such as my Lenovo
Haswell laptop.
This provides working X with the small complication of a console cursor
permanently overlaid on the upper-left corner of the screen that will be
dealt with later.
Also remove some redundant screen clearing.
rather than only drivers attached later on. This involves a small amount of
code duplication with dev/fb/fbd.c, which will fixed later on.
Also improve performance of vt_blank() by making it not read from the
framebuffer unnecessarily.
USB 2.0 port mask in addition to the USB 3.0 port mask. The hardware
does not always accept when writing -1U to the port switching
registers.
MFC after: 3 days
Tested by: Huang Wen Hui <huanghwh@gmail.com>
not done after the call to m_defrag(). This fixes a problem
where m_pullup() would prepend an mbuf to the list created
by m_defrag() making the chain greater than 32 again.
Tested by: rcarter@pinyon.org
Reviewed by: yongari, jfv
MFC after: 2 weeks
firmware allows up to 48B to be read this way but the driver limits
itself to 8B at a time to remain compatible with old cxgbetool
binaries.
MFC after: 1 week
that it can connect to switches at speeds other than 1gb.
This requires changing the reference clock speed. Since we still don't
have a general clock API that lets a SoC-independant driver manipulate its
own clocks, this change includes a weak reference to a routine named
cgem_set_ref_clk(). The default implementation is a no-op; SoC-specific
code can provide an implementation that actually changes the speed.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
to uncacheable. This leads to execrable console performance. Once PMAP is
up, remap the framebuffer as write-combining. This reduces boot time on my
laptop by 60% when booting with EFI.
MFC after: 2 weeks
- Remove 4 extra bytes from the ethernet payload.
- The maximum RX buffer was incorrectly set. Increase it to 64K for
now, until the exact limit is understood.
- Enable hardware checksumming again.
- Make hardware data structure packed.
MFC after: 3 days
The Tx interrupt is now kept disabled in the common case, only
enabled when the number of free descriptors in the queue falls
below a threshold. Transmitted frames are cleared from the VQ
before subsequent transmit, or in the watchdog timer.
This was a very big performance improvement for an experimental
Netmap bhyve backend.
MFC after: 1 month
- add missing rcvif in mbuf
- add missing ipacket stat
- remove uncessary mbuf copy on output path
- fix deadlock of the TX engine in case of error
Obtained from: NETASQ
MFC after: 2 weeks
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
Previously ISID was changed every time, that made impossible correct
persistent reservation, because reconnected session was identified as
completely new one.
Reviewed by: trasz
MFC after: 1 week
Update some comments on code, specifying the correct vlans used on switch
setup.
Advertise the proper switch operation mode (the rtl8366rb only support
dot1q vlans).
This fixes the breakage that i introduced on r249752 and make the rtl8366rb
switch works again with etherswitchcfg(8).
Tested on TP-Link 1043ND.
Tested by: me, Harm Weites (harm at weites.com)
- Don't discard frames if the dropped or error flag is set.
- Don't remove the last 4-bytes of every packet.
- Add extra range check for data position offset when receiving data.
MFC after: 1 day
PR: 191432
The array index for the callchain is getting double-incremented -- both in the
loop and the storing. It should only be incremented in one location.
Also, constrain the stack pointer range check.
MFC after: 2 weeks
1. oce_multiq_start(): make sure the buffer is consumed even on ENXIO
2. oce_multiq_transmit(): there is an extra call to drbr_enqueue()
causing the mbuf to be enqueued twice when the NIC's queue is full,
and potential panics
3. oce_multiq_transmit(): same problem fixed recently in ixgbe (r267187)
and other drivers: if the mbuf is enqueued, the proper return value is 0
Submitted by: Stefano Garzarella
MFC after: 3 days
rules prevent the USB serial module to be unloaded before any client
modules. This patch ensures that the "ucom_mtx" mutex is destroyed
last when doing a system uninit in a monotolith build aswell.
MFC after: 3 days
The ixgbe(4) hardware is capable of RSS hashing RX packets and doing RSS
queue selection for up to 8 queues.
However, even if multi-queue is enabled for ixgbe(4), the RX path doesn't use
the RSS flowid from the received descriptor. It just uses the MSIX queue id.
This patch does a handful of things if RSS is enabled:
* Instead of using a random key at boot, fetch the RSS key from the RSS code
and program that in to the RSS redirection table.
That whole chunk of code should be double checked for endian correctness.
* Use the RSS queue mapping to CPU ID to figure out where to thread pin
the RX swi thread and the taskqueue threads for each queue.
* The software queue is now really an "RSS bucket".
* When programming the RSS indirection table, use the RSS code to
figure out which RSS bucket each slot in the indirection table maps
to.
* When transmitting, use the flowid RSS mapping if the mbuf has
an RSS aware hash. The existing method wasn't guaranteed to align
correctly with the destination RSS bucket (and thus CPU ID.)
This code warns if the number of RSS buckets isn't the same as the
automatically configured number of hardware queues. The administrator
will have to tweak one of them for better performance.
There's currently no way to re-balance the RSS indirection table after
startup. I'll worry about that later.
Additionally, it may be worthwhile to always use the full 32 bit flowid if
multi-queue is enabled. It'll make things like lagg(4) behave better with
respect to traffic distribution.
The igb(4) hardware is capable of RSS hashing RX packets and doing RSS
queue selection for up to 8 queues. (I believe some hardware is limited
to 4 queues, but I haven't tested on that.)
However, even if multi-queue is enabled for igb(4), the RX path doesn't use
the RSS flowid from the received descriptor. It just uses the MSIX queue id.
This patch does a handful of things if RSS is enabled:
* Instead of using a random key at boot, fetch the RSS key from the RSS code
and program that in to the RSS redirection table.
That whole chunk of code should be double checked for endian correctness.
* Use the RSS queue mapping to CPU ID to figure out where to thread pin
the RX swi thread and the taskqueue threads for each queue.
* The software queue is now really an "RSS bucket".
* When programming the RSS indirection table, use the RSS code to
figure out which RSS bucket each slot in the indirection table maps
to.
* When transmitting, use the flowid RSS mapping if the mbuf has
an RSS aware hash. The existing method wasn't guaranteed to align
correctly with the destination RSS bucket (and thus CPU ID.)
This code warns if the number of RSS buckets isn't the same as the
automatically configured number of hardware queues. The administrator
will have to tweak one of them for better performance.
There's currently no way to re-balance the RSS indirection table after
startup. I'll worry about that later.
Additionally, it may be worthwhile to always use the full 32 bit flowid if
multi-queue is enabled. It'll make things like lagg(4) behave better with
respect to traffic distribution.
reset device task request from the driver. If the drive fails to respond
with a signature FIS, the driver would previously get into an endless retry
loop, stalling all I/O to the drive and keeping user processes stranded.
Instead, fail the i/o and invalidate the device if the task management
command times out. This is controllable with the sysctl and tunable
hw.isci.fail_on_task_timeout
dev.isci.0.fail_on_task_timeout
The default for these is 1.
Reviewed by: jimharris
Obtained from: Netflix, Inc.
MFC after: 2 days
If a controller is set to JBOD, it has no RAID functions turned on.
Populate even more of the firmware specification headers, copied from
cciss_vol_status.
Reviewed by: Benesh, Scott <scott.benesh@hp.com>
MFC after: 2 weeks
If cam_periph_find() doesn't locate the path we requested, bail to error
condition.
Acquire ciss->mtx for this operation.
Reviewed by: "Benesh, Scott" <scott.benesh@hp.com>
MFC after: 2 weeks
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
implement options TERMINAL_{KERN,NORM}_ATTR. These are aliased to
SC_{KERNEL_CONS,NORM}_ATTR and like these latter, allow to change the
default colors of normal and kernel text respectively.
Note on the naming: Although affecting the output of vt(4), technically
kern/subr_terminal.c is primarily concerned with changing default colors
so it would be inconsistent to term these options VT_{KERN,NORM}_ATTR.
Actually, if the architecture and abstraction of terminal+teken+vt would
be perfect, dev/vt/* wouldn't be touched by this commit at all.
Reviewed by: emaste
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
With this change and previous work from ray@ it will be possible to put
both in GENERIC, and have one enabled by default, but allow the other to
be selected via the loader.
(The previous implementation had separate kern.vt.disable and
hw.syscons.disable tunables, and would panic if both drivers were
compiled in and neither was explicitly disabled.)
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
configs. Switch the BERI_NETFPGA_MDROOT to 64bit by default.
Give we have working interrupts also cleanup the extra polling CFLAGS from
the module Makefile.
MFC after: 2 weeks
time by setting NF10BMAC_64BIT and using a REGWTYPE #define to set correct
variable and return value widths.
Adjust comments to indicate the 32 or 64bit register widths.
MFC after: 2 weeks
PCI root bridges except for the one known-valid case on x86 where bridges
claim the I/O port registers used for PCI config space access.
Tested by: Hilko Meyer <hilko.meyer@gmx.de>
MFC after: 1 week
Prevent the Xen and VirtIO balloon drivers from marking pages as
wired. This prevents them from increasing the system wired page count,
which can lead to mlock failing because of hitting the limit in
vm.max_wired.
In the Xen case make sure pages are zeroed before giving them back to
the hypervisor, or else we might be leaking data. Also remove the
balloon_{append/retrieve} and link pages directly into the
ballooned_pages queue using the plinks.q field in the page struct.
Sponsored by: Citrix Systems R&D
Reviewed by: kib, bryanv
Approved by: gibbs
dev/virtio/balloon/virtio_balloon.c:
- Don't allocate pages with VM_ALLOC_WIRED.
dev/xen/balloon/balloon.c:
- Don't allocate pages with VM_ALLOC_WIRED.
- Make sure pages are zeroed before giving them back to the
hypervisor.
- Remove the balloon_entry struct and the balloon_{append/retrieve}
functions and use the page plinks.q entry to link the pages
directly into the ballooned_pages queue.
peripheral devices. When transmitting (rx) from slave to master,
sometimes nAKC delays. As a result, some slaves fails their
transmission.
Submitted by: Masanori OZAWA <ozawa@ongs.co.jp>
Reviewed by: brix
MFC after: 1 week
The sound drivers that use own buffer management can use sndbuf_setup
and not do any busdma allocation, so the driver will end up with the
managed buffer but no valid dma map and tag for it. Avoid calling
bus_dmamem_free in such cases.
Reported by: ache
Missed in review by: kan
separate argument structure with added level_type field for
CPUID_CPUID_COUNT request.
Reviewed by: attilio (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Assume the number of description used is reasonable value to
increment this otherwise opaque field by.
While here, reduce a minor difference between the legacy and
multiqueue transmit paths.
MFC after: 1 week
This requires the VMware vmxnet3 device to flip the start of packet
descriptor's generation before the rest of the packet's descriptors
have been loaded into the Rx ring. I've never observed this behavior,
and it seems to make the most sense not to do it this way. But it is
not a lot of work for the driver to handle this situation just in case.
MFC after: 1 week
The sbp_cam_detach_target can be called from sbp_post_explore function
on the first target that is not really attached and it was written with
the corresponding safety check in place to tolerate that. Unfortunately
the recent locking cleanup did add a locking assertion that tries to
dereference the target->sbp pointer unconditionally, which causes less
than desirable outcome. Since the assertion is useful, just initialize
the target sbp pointer once when sbp device is being initialized instead
of when the target is being attached. This makes assertion work in all
cases and fixes the crash on boot.
performing cpuid calls.
Add also a new way to specify the level type to cpucontrol(8) as
reported in the manpage.
Sponsored by: EMC / Isilon storage division
Reviewed by: bdrewery, gcooper
Testerd by: bdrewery
instead of trying to cache it.
Previously, we only trusted the state if we did not have a cached state.
However, once a state was cached, the _STA method was always ignored.
Specifically, once a power resource had been turned on once (e.g.
during resume), the driver assumed it was always on even if _STA said it
was off and never turned it back on. This prevented the power resource
from being turned back on if a laptop was resumed twice, for example.
To fix, just remove the cached state entirely and always use the results
of _STA. The loops already skip any resources where _STA fails.
Submitted by: trasz (initial patch to invoke _ON)
MFC after: 1 week
- Don't compare the DMA map to NULL to determine if bus_dmamap_unload()
should be called when releasing a static allocation. Instead, compare
the bus address against 0.
- Don't assume that the DMA map for static allocations is NULL. Instead,
save the value set by bus_dmamem_alloc() so it can later be passed to
bus_dmamem_free(). Also, add missing calls to bus_dmamap_unload() in
these cases before freeing the buffer.
- Use the bus address from the bus_dma callback instead of calling
vtophys() on the address allocated by bus_dmamem_alloc().
Reviewed by: kan
- Add missing calls to bus_dmamap_unload() in et(4).
- Check the bus address against 0 to decide when to call
bus_dmamap_unload() instead of comparing the bus_dma map against NULL.
- Check the virtual address against NULL to decide when to call
bus_dmamem_free() instead of comparing the bus_dma map against NULL.
- Don't clear bus_dma map pointers to NULL for static allocations.
Instead, treat the value as completely opaque.
- Pass the correct virtual address to bus_dmamem_free() in wpi(4) instead
of trying to free a pointer to the virtual address.
Reviewed by: yongari
the queue where to enqueue pages that are going to be unwired.
- Add stronger checks to the enqueue/dequeue for the pagequeues when
adding and removing pages to them.
Of course, for unmanaged pages the queue parameter of vm_page_unwire() will
be ignored, just as the active parameter today.
This makes adding new pagequeues quicker.
This change effectively modifies the KPI. __FreeBSD_version will be,
however, bumped just when the full cache of free pages will be
evicted.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Tested by: pho
Switch the initialization of gnttab to use an unused physical memory
range for both PVHVM and PVH.
In the past PVHVM was using the xenpci BAR, but there's no reason to
do that, and in fact FreeBSD was probably doing it because it was the
way it was done in Windows, were drivers cannot probably request for
unused physical memory ranges, but it was never enforced in the
hypervisor.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
xen/gnttab.c:
- Allocate contiguous physical memory for grant table frames for both
PVHVM and PVH.
- Since gnttab is not a device, use the xenpv device in order to
request for this allocation.
dev/xen/xenpci/xenpcivar.h:
dev/xen/xenpci/xenpci.c:
- Remove the now unused xenpci_alloc_space and xenpci_alloc_space_int
functions.
xen/gnttab.h:
- Change the prototype of gnttab_init and gnttab_resume, that now
takes a device_t parameter.
dev/xen/control/control.c:
x86/xen/xenpv.c:
- Changes to accomodate the new prototype of gnttab_init and
gnttab_resume.
Add the PV shutdown hook to PVH.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
dev/xen/control/control.c:
- Make xen_pv_shutdown_final available on XENHVM builds.
- Register the Xen PV shutdown hook for PVH guests.
Create a dummy bus so top level Xen devices can attach to it (instead
of attaching directly to the nexus). This allows to have all the Xen
related devices grouped under a single bus.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/xenpv.c:
- Attach the xenpv bus when running as a Xen guest.
- Attach the ISA bus if needed, in order to attach syscons.
conf/files.amd6:
conf/files.i386:
- Include the xenpv.c file in the build of i386/amd64 kernels using
XENHVM.
dev/xen/console/console.c:
dev/xen/timer/timer.c:
xen/xenstore/xenstore.c:
- Attach to the xenpv bus instead of the Nexus.
dev/xen/xenpci/xenpci.c:
- Xen specific devices on PVHVM guests are no longer attached to the
xenpci device, they are instead attached to the xenpv bus, remove
the now unused methods.
The header structure consists of two 1-byte elements, but it must always
be describable by a single SG entry. Note for consistency, specify the
alignment everywhere, even if the structure has the appropriate natural
alignment since it contains a uint16_t.
Obtained from: DragonFlyBSD
MFC after: 1 week
These defines are applicable to userland too, but virtqueue.h contains
the kernel virtqueue interface, and is therefore not usable in userland.
Note that Linux places these defines in virtio_ring.h, but I don't want
the drivers including this header file to keep the VirtIO ring opaque to
everything but the virtqueue.
MFC after: 1 week
The eventual goal is to share this file with userland, so
remove the macro that is only specific for virtio_pci(4).
Instead, add the VIRTIO_PCI_CONFIG_OFF macro from Linux to
get the config size whether MSIX is enabled or not.
MFC after: 1 week
NULL to determine if bus_dmamap_unload() or bus_dmamem_free() should be
called. Instead, check the associated bus and virtual addresses.
- Don't clear static DMA maps to NULL.
Reviewed by: jfv
freeing them instead of after.
- Check the bus address of a static DMA buffer to decide if the associated
map should be unloaded.
- Don't try to destroy bus dma maps for static DMA buffers.
Reviewed by: davidcs
- Don't call xpt_free_path() in os_query_remove_device() and
always return TRUE.
- Update os_buildsgl() to support build logical SG table which
will be used by lower RAID module.
- Return CAM_SEL_TIMEOUTstatus for SCSIcommand failed as target
missing.
Many thanks to HighPoint for providing this driver update.
Submitted by: Steve Chang
Reviewed by: mav
MFC after: 3 days
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
don't create a map before calling bus_dmamem_alloc() (such maps were
leaked). It is believed that the extra destroy of the map was generally
harmless since bus_dmamem_alloc() often uses special maps for which
bus_dmamap_destroy() is a no-op (e.g. on x86).
Reviewed by: scottl
shutdown by putting the former under !rebooting and turning the latter into
debug messages.
Reviewed by: hps
MFC after: 1 week
Sponsored by: Bally Wulff Games & Entertainment GmbH
- Use the existing vbus locks instead of Giant for the CAM sim lock.
- Use callout(9) instead of timeout(9).
- Mark the interrupt handler as MPSAFE.
- Don't attempt to pass data in the softc from probe() to attach().
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
Assisted by: delphij
* The way rings are updated changed with the last API bump.
Also sync ->head when moving slots in netmap_sw_to_nic().
* Remove a crashing selrecord() call.
* Unclog the logic surrounding netmap_rxsync_from_host().
* Add timestamping to RX host ring.
* Remove a couple of obsolete comments.
Submitted by: Franco Fichtner
MFC after: 3 days
Sponsored by: Packetwerk
Apparently for VMware Fusion (and presumably VMware Workstation/Player
since the PR states TSO is broken there too, but I cannot test), the
TCP header pseudo checksum calculated should only include the protocol
(IPPROTO_TCP) value, not also the lengths as the stack does instead.
VMware ESXi seems to ignore whatever value is in the TCP header checksum,
and it is a bit surprising there is a different behavior between the
VMware products. And it is unfortunate that on ESXi we are forced to do
this extra bit of work.
PR: kern/185849
MFC after: 3 days
on USB HUBs by moving the code into the USB explore threads. The
deadlock happens because child devices of the USB HUB don't have the
expected reference count when called from outside the explore
thread. Only the HUB device itself, which the IOCTL interface locks,
gets the correct reference count.
MFC after: 3 days
- Revert r265427. It appears we are halting the DWC OTG host
controller schedule if we process events only at every SOF. When doing
split transactions we rely on that events are processed quickly and
waiting too long might cause data loss.
- We are not always able to meet the timing requirements of interrupt
endpoint split transactions. Switch from INTERRUPT to CONTROL endpoint
type for interrupt endpoint events until further, hence CONTROL
endpoint events are more relaxed, reducing the chance of data
loss. See comment in code for more in-depth explanation.
- Simplify TT scheduling.
MFC after: 3 days
- Remove double buffering interrupt and isochronous traffic via the
transaction translator. It can be avoided because the DWC OTG will
always delay the start split transactions for interrupt and
isochronous traffic, but will not delay the complete split
transactions, if we set the odd frame bit correctly.
- Need to check the transfer cache field in the device done function
to be sure all allocated channels are freed and not the transfer first
one. This seems to resolve the control endpoint transfer type quirk
which is now removed.
- Make sure any received data upon TX is dumped else RX path will
stop.
- Transmit isochronous data before receiving isochronous data as a
means to optimise the TT schedule.
- Implement a simple TT bandwidth scheduler.
- Cleanup use of old "td->error" variable.
- On interrupt IN traffic via the transaction translator we simply
ignore missed transfer opportunities and silently retry the
transaction upon next available time slot.
MFC after: 3 days
"Terminus BSD Console" is a derivative of Terminus that is provided
by Mr. Dimitar Zhekov under the 2-clause BSD license for use by the FreeBSD vt(4) console.
Reviewed by: jhb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
- Properly align temporary buffer to 32-bit.
- Add an extra parenthesis to make expression clear.
- Range check the association ID received from hardware.
MFC after: 1 week
A similar fix should be applied to vmxnet, ixgbe, igb, i40e.
(some of them previously reported by Michael Tuexen)
Drivers using if_transmit are correct, and so are most of the
other drivers that reassing if_transmit.
Among other things, this bug causes panics when using netmap emulation
on top of generic drivers.
Approved by: bryanv
MFC after: 3 days
Core i7 and Westmere processors, the uncore PMC subsystem is
completely different from the uncore PMC on smaller versions of CPUs.
Disable existing uncore hwpmc code for EX, otherwise non-existing MSRs
are accessed.
The cores PMCs seems to be identical for non-EX and EX, according to
the SDM.
Reviewed by: davide, fabient
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
- The R92S_TCR register is an 8-bit register. Don't access it like a
16-bit register.
- Disable parsing the delete station event, due to many false events.
- Ensure that there is only one transfer queue for each endpoint, so
that packets transmitted don't get out of order.
MFC after: 1 week
o Always init locks and cv ASAP.
o Initialize driver-independent parts even if driver probing fail.
o Allow to call vt_upgrade anytime, for later loaded drivers.
o New window flag VWF_READY, to track if window already initialized.
Other updates:
o Pass vd as a cookie for kbd_allocate.
o Do not blank window on driver replacement.
Tested by: hselasky (RPi), emaste(VGA, EFIFB, KMS), me
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
interface allows the ifnet structure to be defined as an opaque
type in NIC drivers. This then allows the ifnet structure to be
changed without a need to change or recompile NIC drivers.
Put differently, NIC drivers can be written and compiled once and
be used with different network stack implementations, provided of
course that those network stack implementations have an API and
ABI compatible interface.
This commit introduces the 'if_t' type to replace 'struct ifnet *'
as the type of a network interface. The 'if_t' type is defined as
'void *' to enable the compiler to perform type conversion to
'struct ifnet *' and vice versa where needed and without warnings.
The functions that implement the API are the only functions that
need to have an explicit cast.
The MII code has been converted to use the driver API to avoid
unnecessary code churn. Code churn comes from having to work with
both converted and unconverted drivers in correlation with having
callback functions that take an interface. By converting the MII
code first, the callback functions can be defined so that the
compiler will perform the typecasts automatically.
As soon as all drivers have been converted, the if_t type can be
redefined as needed and the API functions can be fix to not need
an explicit cast.
The immediate benefactors of this change are:
1. Juniper Networks - The network stack implementation in Junos
is entirely different from FreeBSD's one and this change
allows Juniper to build "stock" NIC drivers that can be used
in combination with both the FreeBSD and Junos stacks.
2. FreeBSD - This change opens the door towards changing ifnet
and implementing new features and optimizations in the network
stack without it requiring a change in the many NIC drivers
FreeBSD has.
Submitted by: Anuranjan Shukla <anshukla@juniper.net>
Reviewed by: glebius@
Obtained from: Juniper Networks, Inc.
Reorganize the previous contexts of the file as it is in Linux. The
eventual goal is to install the header files and share them between
the kernel and bhyve.
MFC after: 1 week
At attach, print the SCL and SDA pin numbers.
Remove a stray blank line.
Remove the GPIOBUS locking from gpioiic_reset(), it is already called with
this lock held. This fixes a crash when you try to scan the iicbus with
i2c(8).
get_scatter_segment() in get_fl_payload() fails. While here,
fix the code to adjust fl_bufs_used when a failure occurs for
any other scatter segment.
MFC after: 3 days
If a vt(4) font does not exactly fit the screen dimensions, the console
window is offset so that it is centered. A rectangle is drawn at the
top, left, right, and bottom of the screen, to erase any leftovers that
are outside of the new usable console area.
If the x offset or y offset is 0 then the left border or top border
respectively is not drawn. The right and bottom borders may be one
pixel larger than necessary due to rounding, and are always drawn.
Prior to this change a 0 offset would result in a panic when calling
vt_drawrect with an x or y coordinate of -1.
Sponsored by: The FreeBSD Foundation
vt_grow may be called with a new size that's larger than previous but
does not require reallocation - for example, when the number of columns
is the same and new number of rows is less than the history size.
Prior to this change we would fail to update vb_scr_size, and then hit
a KASSERT when trying to write to the newly visible rows.
Sponsored by: The FreeBSD Foundation
- Update FDT file for BERI DE4 boards.
- Add needed kernel configuration keywords.
- Rename module to saf1761otg so that the device unit number does not
interfere with the hardware ID in dmesg.
Sponsored by: DARPA, AFRL
- Use an interrupt filter for handling the data path interrupts. This
increases the throughput significantly.
- Implement support for USB suspend and resume in USB host mode.
Sponsored by: DARPA, AFRL
- Make the USB hardware skip PTDs which are not allocated.
- Peek host memory twice. Sometimes the PTD status is incorrectly
returned as zero.
- Ensure the host channel is always freed when software TD
is completing.
- Add correct configuration of interrupt polarity and type.
- Set CERR to 2 for asynchronous traffic to avoid having to
reactivate the PTD when a NAK token is received.
- Fix detection of STALL PID.
Sponsored by: DARPA, AFRL
physical addresses.
- Nuke the unused softc of emujoy(4).
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
- Based on actual usage and on what Linux does, dummy_page.addr should
contain the physical bus address of the dummy page rather than its
virtual one. As a side-effect, correcting this bug fixes compilation
with PAE support enabled by getting rid of an inappropriate cast.
- Also based on actual usage of dummy_page.addr, theoretically Radeon
devices could do a maximum of 44-bit DMA. In reality, though, it is
more likely that they only support 32-bit DMA, at least that is what
radeon_gart_table_ram_alloc() sets up for, too. However, passing ~0
to drm_pci_alloc() as maxaddr parameter translates to 64-bit DMA on
amd64/64-bit machines. Thus, use BUS_SPACE_MAXSIZE_32BIT instead,
which the existing 32-bit DMA limits within the drm2 code spelled as
0xFFFFFFFF should also be changed to.
Reviewed by: dumbbell
MFC after: 1 week
Sponsored by: Bally Wulff Games & Entertainment GmbH
- Switch from timeout() to callout_*() for per-request timers.
- Use device_find_child() in the identify routine.
- Use device_printf() instead of passing device_get_nameunit() to
printf().
- Expand the SBP_LOCK coverage simplifying the locking.
- Uninline STAILQ_FOREACH_SAFE().
Tested by: sbruno
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.
For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.
With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.
trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43🆎cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43🆎cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...
Relnotes: Yes
Sponsored by: Chelsio Communications.
uart2: <Intel AMT - PM965/GM965 KT Controller> port 0x1830-0x1837
mem 0xfe024000-0xfe024fff irq 17 at device 3.3 on pci0
uart2: console (115200,n,8,1)
Tested as tty and serial console. Seems "fine"
- Put "_LE_" into the register access macros to indicate little endian
byte order is expected by the hardware.
- Avoid using the bounce buffer when not strictly needed. Try to move
data directly using bus-space functions first.
- Ensure we preserve the reserved bits in the power down mode
register. Else the hardware goes into a non-recoverable state.
- Always use 32-bit access when writing or reading registers or FIFOs,
because the hardware is 32-bit oriented and don't really understand 8-
and 16-bit access.
- Correct writes to the memory address register. There is no need to
shift the register offset.
- Correct interval for interrupt endpoints.
- Optimise 90ns internal memory buffer read delay.
- Rename PDT into PTD, which is how the datasheet writes it.
- Add missing programming for activating host controller PTDs.
Sponsored by: DARPA, AFRL
Idle priority is not even time-share, so if system is busy in any way,
those events may never be executed. Since in some cases system waits
for events processed by that thread, that may cause deadlocks.
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
direction isochronous transfers.
- Remove setting of fields which does not belong to the respective
TRBs. These fields are currently set as zero and this is more a
cosmetic change.
MFC after: 3 days
Submitted by: Horse Ma <HMa@wyse.com>
- Make sure TX/RX lists don't leak and are only allocated once.
- Fix off-by one transfer index computation.
- Give firmware loading more time.
MFC after: 3 days
be a race when using a single active queue for all transmit types.
- Last argument of usb_pause_mtx() is ticks and not milliseconds.
- Remove unused watchdog.
- Remove some unused fields from the RSU softc structure.
- Workaround usbd_transfer_start() recursion from inside of completion
callback.
MFC after: 3 days
- Need to set the pre-fetch memory address when reading the host memory.
- We currently assume that no endianness conversion is needed.
Sponsored by: DARPA, AFRL
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
Intel 40G Ethernet Controller XL710 Family. This is
the core driver, a VF driver called i40evf, will be
following soon. Questions or comments to myself or
my co-developer Eric Joyner. Cheers!
- Implement support for interrupt filters in the DWC OTG driver, to
reduce the amount of CPU task switching when only feeding the FIFOs.
- Add common spinlock to the USB bus structure.
MFC after: 2 weeks
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
it doesn't leak through when the command structure is reused for a user
command without a data buffer.
PR: amd64/189668
Tested by: Pete Long <pete@nrth.org>
MFC after: 1 week
Previously only TX IP checksum offloading was disabled but it's
reported that TX checksum offloading for UDP datagrams with IP
options also generates corrupted frames. Reporter's controller is
RTL8168CP but I guess RTL8168C also have the same issue since it
shall share the same core.
Reported and tested by: tuexen
the main processing queue, clear the NAK counter for any associated
BULK or CONTROL transfers and poll the endpoint(s) for 1 millisecond
at 125us rate interval, before going into slow, 10ms, NAK polling mode
again. This has the effect that typical ping-ping protocols respond
quicker when initiated from the USB host.
MFC after: 2 weeks
The last obstacle to switching PowerPC entirely to vt is that the Playstation 3
framebuffer driver needs to be ported over. This only applies for powerpc64,
however.
on my G4 iBook by more than half. Still 10% slower than syscons, but that's
much better than a factor of 2.
The slowness had to do with pathological write performance on 8-bit
framebuffers, which are almost universally used on Open Firmware systems.
Writing 1 byte at a time, potentially nonconsecutively, resulted in many
extra PCI write cycles. This patch, in the common case where it's writing
one or several characters in an 8x8 font, gangs the writes together into
a set of 32-bit writes. This is a port of r143830 to vt(4).
The EFI framebuffer is also extremely slow, probably for the same reason,
and the same patch will likely help there.
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
- For non-periodic traffic we only need to wait two SOFs before
disabling the channel.
- Make sure we release the TX FIFO tracking level after the host
channel is disabled.
- Make sure the host channel state gets reset/disabled initially.
- Two minor code style changes.
MFC after: 2 weeks
- Rework how we allocate and free USB host channels, so that we only
allocate a channel if there is a real packet going out on the USB
cable.
- Use BULK type for control data and status, due to instabilities in
the HW it appears.
- Split FIFO TX levels into one for the periodic FIFO and one for the
non-periodic FIFO.
- Use correct HFNUM mask when scheduling host transactions. The HFNUM
register does not count the full 16-bit range.
- Correct START/COMPLETION slot for TT transactions. For INTERRUPT and
ISOCHRONOUS type transactions the hardware always respects the ODDFRM
bit, which means we need to allocate multiple host channels when
processing such endpoints, to not miss any so-called complete split
opportunities.
- When doing ISOCHRONOUS OUT transfers through a TT send all data
payload in a single ALL-burst. This deacreases the likelyhood for
isochronous data underruns.
- Fixed unbalanced unlock in case of "dwc_otg_init_fifo()" failure.
- Increase interrupt priority.
MFC after: 2 weeks
have implemented the PIM_NOSCAN rescan functionality will have it
enabled.
This is a no-op for head.
Reviewed by: slm
Sponsored by: Spectra Logic Corporation
MFC after: 3 days
TLR is necessary for reliable communication with SAS tape drives.
This was broken by change 246713 in the mps(4) driver. It changed the
cm_data field for SCSI I/O requests to point to the CCB instead of the data
buffer. So, instead, look at the CCB's data pointer to determine whether
or not we're talking to a tape drive.
Also, take the residual into account to make sure that we don't go off the
end of the request.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
cards. LSI has been maintaining this driver outside of the FreeBSD
tree. It overlaps support of ThunderBolt and Invader cards that mfi(4)
supports. By default mfi(4) will attach to cards. If the tunable:
hw.mfi.mrsas_enable=1
is set then mfi(4) will not probe and attach to these newer cards and
allow mrsas(4) to attach. So by default this driver will not effect
a FreeBSD system unless mfi(4) is removed from the kernel or the
tunable is enabled.
mrsas(4) attaches disks to the CAM layer so it depends on CAM and devices
show up as /dev/daX. mfiutil(8) does not work with mrsas. The FreeBSD
version of MegaCli and StorCli from LSI do work with mrsas. It appears
that StorCli only works with mrsas. MegaCli appears to work with mfi(4)
and mrsas(4).
It would be good to add mfiutil(4) support to mrsas, emulations modes,
kernel logging, device aliases to ease the transition between mfi(4)
and mrsas(4).
Style issues should be resolved by LSI when they get committers approved.
The plan is get this driver in FreeBSD 9.3 to improve HW support.
Thanks to LSI for developing, testing and working with FreeBSD to
make this driver co-exist in FreeBSD. This improves the overall
support of MegaRAID SAS.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: scottl
MFC after: 3 days
Sponsored by: LSI
mprsas_SSU_to_SATA_devices().
This fixes an assertion on shutdown with INVARIANTS enabled with SATA
drives present on an IR firmware controller.
Reviewed by: Steve McConnell <stephen.mcconnell@avagotech.com>.
MFC after: 3 days
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
This problem only occurs on versions of FreeBSD prior to the recent CAM
locking changes. (i.e. stable/9 and older versions of stable/10) This
change should be a no-op for head and stable/10.
If a path isn't specified, xpt_register_async() will create a fully
wildcarded path and acquire a lock (the XPT lock in older versions,
and via xpt_path_lock() in newer versions) to call xpt_action() for the
XPT_SASYNC_CB CCB. It will then drop the lock and if the requested event
includes AC_FOUND_DEVICE or AC_PATH_REGISTERED, it will get the caller up
to date with any device arrivals or path registrations.
The issue is that before the locking changes, each SIM lock would get
acquired in turn during the EDT tree traversal process. If a path is
specified for xpt_register_async(), it won't acquire and drop its own lock,
but instead expects the caller to hold its own SIM lock. That works for
the first part of xpt_register_async(), but causes a recursive lock
acquisition once the EDT traversal happens and it comes to the SIM in
question. And it isn't possible to call xpt_action() without holding a SIM
lock.
The locking changes fix this by using the XPT topology lock for EDT
traversal, so it is no longer an issue to hold the SIM lock while calling
xpt_register_async().
The solution for FreeBSD versions before the locking changes is to request
notification of all device arrivals (so we pass a NULL path into
xpt_register_async()) and then filter out the arrivals that are not ours.
MFC After: 3 days
Sponsored by: Spectra Logic Corporation
used.
It turns out that the RX DMA engine does the same last-descriptor-link-
pointer-re-reading trick that the TX DMA engine. That is, the hardware
re-reads the link pointer before it moves onto the next descriptor.
Thus we can't free a descriptor before we move on; it's possible the
hardware will need to re-read the link pointer before we overwrite
it with a new one.
Tested:
* AR5416, STA mode
TODO:
* more thorough AP and STA mode testing!
* test on other pre-AR9380 NICs, just to be sure.
* Break out the RX descriptor grabbing bits from the RX completion
bits, like what is done in the RX EDMA code, so ..
* .. the RX lock can be held during ath_rx_proc(), but not across
packet input.
o Declare vt(4) drivers dataset.
o Create single static structures for all early drivers.
o Add vt(4) to be by default in the kernel consoles list.
o Create one more sysinit point, to be able to initialize memory and lock
requirement of early drivers.
o Implement early drivers select. (Only best available will be selected).
o Fix one missed "return (0)" for VTYLOCK.
o Improve locking for cases when one driver replace another.
o Make driver replacement notification less debug-look-like.
Minor spell fixes.
Sponsored by: The FreeBSD Foundation
reflect when unmapped I/O support was added.
For FreeBSD 10, it arrived just prior to __FreeBSD_version 1000028.
For FreeBSD 9, it arrived just prior to __FreeBSD_version 902001.
Also, fix compiler warnings in mprsas_send_smpcmd() that happen in the
i386 PAE build for non-unmapped I/O builds. These were fixed in mps(4)
in revision 241145, but didn't make it into the mpr(4) driver. This
change should only affect FreeBSD versions outside the above revisions,
and thus doesn't affect head.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
call, which assumes the hardware is awake.
Turn ath_update_mcast() into a routine that's only called from the
net80211 layer - and it forces the hardware awake first.
This fixes a LOR from the EDMA RX path which calls ath_mode_init()
with the RX lock held - the driver lock can't also be grabbed.
This path assumes that the ath_mode_init() callers all wake up
the NIC first.
Tested:
* AR9485, STA mode, powersave
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
sys/systm.h must always come after sys/param.h.
Remove sys/types.h which should never be included together with sys/param.h.
Add sys/malloc.h for correctness even if it seems to don't be needed.
Remove more unused headers found by unusedinc (from bde@) and tested with a
universe build.
Reported by: bde
This allows to run 32bit applications on a 64bit host. This was tested
successfully with Wine (emulators/i386-wine-devel) and StarCraft II.
Submitted by: Jan Kokemüller <jan.kokemueller@gmail.com>
MFC after: 1 week
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
Adjust the exynos and zedboard dts files to use max-frequency (the
documented standard property) instead of clock-frequency.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
The hardware can generate its own frames (eg RTS/CTS exchanges, other
kinds of 802.11 management stuff, especially when it comes to 802.11n)
and these also have PWRMGT flags. So if the VAP is asleep but the
NIC is in force-awake for some reason, ensure that the self-generated
frames have PWRMGT set to 1.
Now, this (like basically everything to do with powersave) is still
racy - the only way to guarantee that it's all actually consistent
is to pause transmit and let it finish before transitioning the VAP
to sleep, but this at least gets the basic method of tracking and
updating the state debugged.
Tested:
* AR5416, STA mode
* AR9380, STA mode
fixes and beacon programming / debugging into the ath(4) driver.
The basic power save tracking:
* Add some new code to track the current desired powersave state; and
* Add some reference count tracking so we know when the NIC is awake; then
* Add code in all the points where we're about to touch the hardware and
push it to force-wake.
Then, how things are moved into power save:
* Only move into network-sleep during a RUN->SLEEP transition;
* Force wake the hardware up everywhere that we're about to touch
the hardware.
The net80211 stack takes care of doing RUN<->SLEEP<->(other) state
transitions so we don't have to do it in the driver.
Next, when to wake things up:
* In short - everywhere we touch the hardware.
* The hardware will take care of staying awake if things are queued
in the transmit queue(s); it'll then transit down to sleep if
there's nothing left. This way we don't have to track the
software / hardware transmit queue(s) and keep the hardware
awake for those.
Then, some transmit path fixes that aren't related but useful:
* Force EAPOL frames to go out at the lowest rate. This improves
reliability during the encryption handshake after 802.11
negotiation.
Next, some reset path fixes!
* Fix the overlap between reset and transmit pause so we don't
transmit frames during a reset.
* Some noisy environments will end up taking a lot longer to reset
than normal, so extend the reset period and drop the raise the
reset interval to be more realistic and give the hardware some
time to finish calibration.
* Skip calibration during the reset path. Tsk!
Then, beacon fixes in station mode!
* Add a _lot_ more debugging in the station beacon reset path.
This is all quite fluid right now.
* Modify the STA beacon programming code to try and take
the TU gap between desired TSF and the target TU into
account. (Lifted from QCA.)
Tested:
* AR5210
* AR5211
* AR5212
* AR5413
* AR5416
* AR9280
* AR9285
TODO:
* More AP, IBSS, mesh, TDMA testing
* Thorough AR9380 and later testing!
* AR9160 and AR9287 testing
Obtained from: QCA
Some code will appear soon that is actually setting the chip powerstate
separate from the self-generated frames power state.
* Allow the AR5416 family chips to actually have the power state changed
from the self generated state change.
Tested (STA mode):
* AR5210
* AR5211
* AR5412
* AR5413
* AR5416
* AR9285
It exposes I/O resources to user space, so that programs can peek
and poke at the hardware. It does not itself have knowledge about
the hardware device it attaches to.
Sponsored by: Juniper Networks, Inc.
the MYBEACON RX filter (only receive beacons which match the BSSID)
or all beacons on the current channel.
* Add the relevant RX filter entry for MYBEACON.
Tested:
* AR5416, STA
* AR9285, STA
TODO:
* once the code is in -HEAD, just make sure that the code which uses it
correctly sets BEACON for pre-AR5416 chips.
Obtained from: QCA, Linux ath9k
the QCA HAL.
This fires off an interrupt if the TSF from the AP / IBSS peer is
wildly out of range. I'll add some code to the ath(4) driver soon
which makes use of this.
TODO:
* verify this didn't break TDMA!
to the hardware.
The QCA HAL has a comment noting that if this isn't done, modifications
to AR_IMR_S2 before AR_IMR is flushed may produce spurious interrupts.
Obtained from: QCA
#gpio-cells property.
Add a new ofw_bus method (OFW_BUS_MAP_GPIOS()) that allows the GPIO
controller to implement its own mapping to deal with gpio-specifiers,
allowing the decoding of gpio-specifiers to be controller specific.
The default ofw_bus_map_gpios() decodes the linux standard (#gpio-cells =
<2>) and the FreeBSD standard (#gpio-cells = <3>).
It pass the gpio-specifier flag field to the children as an ivar variable so
they can act upon.
define a few imx_ccm_foo() functions that are implemented by the imx51 or
imx6 ccm code. Of course, the imx6 ccm code is still more a wish than
reality, so for now its implementations just return hard-coded numbers.
a jtag debugging product, which was used on early Beaglebone boards (later
boards used a standard FTDI 2232C product ID). Change the name accordingly,
and also add an entry for XDS100V3, the latest version of that product
which has its own new product ID number.
Device type and revision is now determined from the bcdDevice field and
doesn't need to be in the table at all. The feature that skips creation
of /dev/ttyU* entries for jtag and gpio interfaces is enhanced:
- The feature is now optional, but enabled by default. A tunable and
sysctl are available to control it: hw.usb.uftdi.skip_jtag_interfaces.
- We no longer assume interface #0 is the only jtag interface. Up to
eight interfaces per chip can be flagged as jtag. (Current ftdi chips
support a max of 4 interfaces; this leaves room for growth.)
- Some manufacturers don't change the product ID or use the same ID for
different devices intended for both serial-comms and jtag/gpio use.
Often while the product ID is the same, the product name string is
different, so it's now possible to search for the product name in a
table of strings and get the set of non-tty interfaces from that table.
- Add a comment about FTDI and ZLPs.
- Correctly check odditiy of baud rate divisor.
- Correct IOCTL handling for "error" and "event" char.
MFC after: 1 weeks
concurrent updates from any completing transmits in other threads.
This was exposed when doing power save work - net80211 is constantly
doing reassociations and it's causing the rate control state to get
blanked out. This could cause the rate control code to assert.
This should be MFCed to stable/10 as it's a stability fix.
Tested:
* AR5416, STA
MFC after: 7 days
The MAC filter set may be called without softc_lock held in the case of
SIOCADDMULTI and SIOCDELMULTI ioctls. The ioctl handler checks IFF_DRV_RUNNING
flag which implies port started, but it is not guaranteed to remain.
softc_lock shared lock can't be held in the case of these ioctls processing,
since it results in failure where kernel complains that non-sleepable
lock is held in sleeping thread.
Both problems are repeatable on LAG with LACP proto bring up.
Submitted by: Andrew Rybchenko <Andrew.Rybchenko at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 weeks
The existing cleanup code was based on the Atheros reference driver
from way back and stuff that was in Linux ath9k. It turned out to be ..
rather silly.
Specifically:
* The whole method of determining whether there's hardware-queued frames
was fragile and the BAW would never quite work right afterwards.
* The cleanup path wouldn't correctly pull apart aggregate frames in the
queue, so frames would not be freed and the BAW wouldn't be correctly
updated.
So to implement this:
* Pull the aggregate frames apart correctly and handle each separately;
* Make the atid->incomp counter just track the number of hardware queued
frames rather than try to figure it out from the BAW;
* Modify the aggregate completion path to handle it as a single frame
(atid->incomp tracks the one frame now, not the subframes) and
remove the frames from the BAW before completing them as normal frames;
* Make sure bf->bf_next is NULled out correctly;
* Make both aggregate session and non-aggregate path frames now be
handled via the incompletion path.
TODO:
* kill atid->incomp; the driver tracks the hardware queued frames
for each TID and so we can just use that.
This is a stability fix that should be merged back to stable/10.
Tested:
* AR5416, STA
MFC after: 7 days
MAC
* Now that the paused < 0 bugs have been identified, make the DPRINTF()
a device_printf() again. Anything else that shows up here needs to be
fixed immediately.
Tested:
* AR5416, STA mode
MFC after: 7 days
During power save testing I noticed that the cleanup code is being
called during a RUN->RUN state transition. It's because the net80211
stack is treating that (for reasons I don't quitey know yet) as a
reassociation and this calls the node cleanup code. The reason it's
seeing a RUN->RUN transition is because during active power save
stuff it's possible that the RUN->SLEEP and SLEEP->RUN transitions
happen so quickly that the deferred net80211 vap state code
"loses" a transition, namely the intermediary SLEEP transition.
So, this was causing the node reassociation code to sometimes be called
twice in quick succession and this would result in ath_tx_tid_cleanup()
to be called again. The code calling it would always call pause, and
then only call resume if the TID didn't have "cleanup_inprogress" set.
Unfortunately it didn't check if it was already set on entry, so it
would pause but not call resume. Thus, paused would be called more
than once (once before each entry into ath-tx_tid_cleanup()) but resume
would only be called once when the cleanup state was finished.
This doesn't entirely fix all of the issues seen in the cleanup path
but it's a necessary first step.
Since this is a stability fix, it should be merged to stable/10 at some
point.
Tested:
* AR5416, STA mode
MFC after: 7 days
NetFPGA-10G Embedded CPU Ethernet Core.
The current version operates on a simple PIO based interface connected
to a NetFPGA-10G port.
To avoid confusion: this driver operates on a CPU running on the FPGA,
e.g. BERI/mips, and is not suited for the PCI host interface.
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA/AFRL
and normal mode; this makes it possible to compile with the former
by default, but use it only when neccessary. That's especially
important for the userland part.
Sponsored by: The FreeBSD Foundation
this set of patches fixes support for systems with > 32 cores.
Details include
sfxge: RXQ index (not label) comes from FW in flush done/failed events
Change the second argument name of the efx_rxq_flush_done_ev_t and
efx_rxq_flush_failed_ev_t prototypes to highlight that RXQ index (not label)
comes from FW in flush done and failed events.
sfxge: TXQ index (not label) comes from FW in flush done event
Change the second argument name of the efx_txq_flush_done_ev_t prototype to
highlight that TXQ index (not label) comes from FW in flush done event.
sfxge: use TXQ type as label to support more than 32 TXQs
There are 3 TXQs in event queue 0 and 1 TXQ (with TCP/UDP checksum offload)
in all other event queues.
Submitted by: Andrew Rybchenko <Andrew.Rybchenko at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
and finish the job. ncurses is now the only Makefile in the tree that
uses it since it wasn't a simple mechanical change, and will be
addressed in a future commit.
logical volume state changes.
Currently, I view this as a critical fix for users and will MFC this rapidly as
my testing has shown data loss when the disk is failed by removing it when
under some amount of write activity and this code panics the box.
Reviewed by: mav@ scottl@
MFC after: 3 days
Sponsored by: Yahoo! Inc.
Use soreadable()/sowriteable() in socket upcalls to avoid extra wakeups
until we have enough data to read or space to write.
Increase partial receive len from 1K to 128K to not wake up on every
received packet.
This significantly reduces locks congestion and CPU usage and improves
throughput for large I/Os on NICs without TSO and LRO.
Reviewed by: trasz
Sponsored by: iXsystems, Inc.
motherboard. PHY hardware used for the controller responded at
all possible addresses which in turn resulted in having 32 PHYs
for the controller. If driver detects "MSI K9N6PGM2-V2 (MS-7309)"
motherboard, tell miibus(4) PHY is located at 0.
Tested by: Chris H
o Unmute terminal when done with driver replacement.
o Move init fonts to early point.
o Minor cleanup.
MFC after: 6 days
X-MFC-with: r264244 r264242
Sponsored by: The FreeBSD Foundation
{MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S.
Among others, this fixes the hang seen when trying to probe the none-
existent second UART on an actually 1-port chip.
Obtained from: NetBSD (BAR layouts)
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
tracked BAW actually is.
The net80211 code that completes a BAR will set tid->txa_start (the
BAW start) to whatever value was called when sending the BAR.
Now, in case there's bugs in my driver code that cause the BAW
to slip along, we should make sure that the new BAW we start
at is actually what we currently have it at, not what we've sent.
This totally breaks the specification and so this stays a printf().
If it happens then I need to know and fix it.
Whilst here, add some debugging updates:
* add TID logging to places where it's useful;
* use SEQNO().
match how it's used.
This is another bug that led to aggregate traffic hanging because
the BAW tracking stopped being accurate. In this instance, a filtered
frame that exceeded retries would return a non-error, which would
mean the caller would never remove it from the BAW. But it wouldn't
be added to the filtered list, so it would be lost forever. There'd
thus be a hole in the BAW that would never get transmitted and
this leads to a traffic hang.
Tested:
* Routerstation Pro, AR9220 AP
we did suspend it.
The whole suspend/resume TID queue thing is supposed to be a matched
reference count - a subsystem (eg addba negotiation, BAR transmission,
filtered frames, etc) is supposed to call pause() once and then resume()
once.
ath_tx_tid_filt_comp_complete() is called upon the completion of any
filtered frame, regardless of whether the driver had aleady seen
a filtered frame and called pause().
So only call resume() if tid->isfiltered = 1, which indicates that
we had called pause() once.
This fixes a seemingly whacked and different problem - traffic hangs.
What was actually going on:
* There'd be some marginal link with crappy behaviour, causing filtered
frames and BAR TXing to occur;
* A BAR TX would occur, setting the new BAW (block-ack window) to seqno n;
* .. and pause() would be called, blocking further transmission;
* A filtered frame completion would occur from the hardware, but with
tid->isfiltered = 0 which indiciates we haven't actually marked
the queue yet as filtered;
* ath_tx_tid_filt_comp_complete() would call resume(), continuing
transmission;
* Some frames would be queued to the hardware, since the TID is now no
longer paused;
* .. and if some make it out and ACked successfully, the new BAW
may be seqno n+1 or more;
* .. then the BAR TX completes and sets the new seqno back to n.
At this point the BAW tracking would be loopy because the BAW
start was modified but the BAW ring buffer wasn't updated in lock
step.
Tested:
* Routerstation Pro + AR9220 AP
that are being done by the OS.
For now this'll match up with the "wakeups"; although I'll dig deeper into
this to see if we can determine which sleep state the CPU managed to get
into. Most things I've seen these days only expose up to C2 or C3 via
ACPI even though the CPU goes all the way down to C6 or C7.
o Mute terminal while vt(4) driver change in progress.
o Reset VDF_TEXTMODE before init new driver.
o Assign default font, if new driver is not in TEXTMODE.
o Do not update screen while driver changing.
Resolved by: adrian
Reported by: tyler
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
CLOCAL and HUPCL control flags. There are legit reasons for allowing
those to be changed. When /etc/ttys has the "3wire" type (without a
baudrate) for the serial port that is the low-level console, then
this change has no effect.
Obtained from: Juniper Networks, Inc.
other modes supported by the FTDI serial adapter chips.
In addition to adding the new ioctls, this change removes all the code
that reset the chip at attach and open/close time, and also the code
that turned on RTS/CTS flow control on open without any permission to do
so (that was just always a bug in the driver).
When FTDI chips are configured as GPIO or MPSSE or other special-purpose
uses by an attached serial eeprom, the chip will power on with certain
pins driven or floating, and it's important that the driver not do
anything to the chip to perturb that unless it receives a specific
command to do so. When used for "plain old serial comms" the chip
powers on into the right mode and never needs to be reset while it's
running to operate properly, so this change is transparent to most users.
before changing the divisor bits in the register. We were writing a zero
to the register, which clears the enable, but also cleared the divisor bits
at the same time. That's a violation of the sdhci spec, which says the
divisor can only be changed when the clock is disabled. This has worked
okay on most hardware for years, but the TI OMAP controller would misbehave
after changing the divisor improperly.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
Ensure that first_func is set to 0 on every iteration of the PCI slot
enumeration loop after the first. There is a continue statement that would
cause first_func to stay at 1 any PCI device where slot 0 has no functions
until we find a slot that does have a function. This would cause us to
not enumerate the first PCI function on the device.
Credit to markj@ for spotting the bug.
X-MFC-With: r264011
While I'm here, remove aue_eeprom_getword() as its only usage is to
read station address and make it more readable. This change is
inspired by NetBSD.
With this change, aue(4) should work on big endian architectures.
PR: 188177
default wMaxPacketSize (64 or 512 bytes). This actually helps older FTDI
devices (which were USB 1/full speed) more than the new H-series high
speed, but even for the new chips it helps cut the number of interrupts
when doing very high speed (3-12mbaud).
This avoids extra locking in icl_pdu_queue(); the upper layer needs to call
it while holding its own lock anyway, to avoid sending PDUs out of order.
Sponsored by: The FreeBSD Foundation
PCIe Alternate RID Interpretation (ARI) is an optional feature that
allows devices to have up to 256 different functions. It is
implemented by always setting the PCI slot number to 0 and
re-purposing the 5 bits used to encode the slot number to instead
contain the function number. Combined with the original 3 bits
allocated for the function number, this allows for 256 functions.
This is enabled by default, but it's expected to be a no-op on currently
supported hardware. It's a prerequisite for supporting PCI SR-IOV, and
I want the ARI support to go in early to help shake out any bugs in it.
ARI can be disabled by setting the tunable hw.pci.enable_ari=0.
Reviewed by: kib
MFC after: 2 months
Sponsored by: Sandvine Inc.
Recent FDTI chips have the ability to operate at up to 12mbps. The newer
chips with faster clocks have the same usb vendor/product IDs as the older
chips; the bcdDevice field must be used to detect the newer versions. This
change includes a new function to do that instead of using just the IDs from
the vendor/product table.
The code to choose the baud clock divisor is completely rewritten. In
addition to supporting the new higher clock rates, the rewrite fixes a
longstanding bug in the old code which put the high bits of the fractional
part of the divisor into the wrong place in the wIndex field. That bug
was mostly harmless -- it accidentally didn't affect standard baud rates
and would only show up when using relatively fast non-standard rates.
My PCI RID changes somehow got intermixed with my PCI ARI patch when I
committed it. I may have accidentally applied a patch to a non-clean
working tree. Revert everything while I figure out what went wrong.
Pointy hat to: rstone
out 32 is not enough to support a full sized TSO packet.
While I'm here fix a long standing bug introduced in r169632 in
bce(4) where it didn't include L2 header length of TSO packet in
the maximum DMA segment size calculation.
In collaboration with: rmacklem
MFC after: 2 weeks
o Move vd_bitbltchr vga's driver method to vd_maskbitbltchr.
o Implement new vd_bitbltchr method for vga driver. (It do single write for 8
pixels, have to be a bit faster).
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
vt(9) crash on resume fixed, but Xorg still have damaged screen on resume (at
least with i915kms), so better to switch to VT0 before suspend and back on
resume.
Sponsored by: The FreeBSD Foundation
Statically allocated terminal window have not initialized callout handler, so we
have to initialize it even for existing window if it is console window.
Reported by: gjb and many
Tested by: gjb
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
Previous implementation limits put queue size only (when Tx lock can't
be acquired), but get queue may grow unboundedly which results in mbuf
pools exhaustion and latency growth.
Submitted by: Andrew Rybchenko <Andrew.Rybchenko at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
These are needed to diagnose TX hangs that I and hiren are seeing.
Without it, the only way we'll see debugging is by having ATH_DEBUG_SW_TX
enabled and that is going to be very, very spammy.
ATH_DEBUG_RESET is fine; it's only going to be done during stuck beacon
situations in AP mode.
Whilst I'm here, and now that it's behind debugging, let's just disable
the "print only one" conditional. I'll eventually make it more tunable.
Tested:
* AR9220, hostap mode.
create character devices. The deadlock can happen if an application is
issuing IOCTLs which require USB refcounting, at the same time the USB
device is detaching.
There is already a counter in place in the USB device structure to
detect this situation, but it was not always checked ahead of invoking
functions that might destroy character devices, like detach, set
configuration, set alternate interface or detach active kernel driver.
Reported by: Daniel O'Connor <doconnor@gsoft.com.au>
MFC after: 1 week
device is asleep.
This doesn't avoid logging errors for things that are actually OK to
access whilst the chip is asleep (eg, the RTC registers (0x7000->0x70ff
on the AR5416 and later.)
But, this is a pretty good indicator if things are accessed incorrectly.
Tested:
* AR5416, STA
This way the state changes from sleep->awake before the registers are poked
and from awake->sleep after the registers are poked.
This way spurious warnings aren't printed by my (to be committed)
debugging code.
Tested:
* AR5416, STA
Yes, this means that sc_invalid is slightly racy, but there are other
issues here which need fixing.
This fixes a source of eventual LORs - ath_init() grabs ATH_LOCK to do
work and releases it before it calls ieee80211_start_all().
ieee80211_start_all() will grab the net80211 comlock to iterate over
the VAPs.
TODO:
* .. I should just migrate the ieee80211_start_all() work to a
deferred task so it can be done later; it doesn't have to be
immediately done.
Tested:
* AR5416, STA mode
then threads can sleep on the pip condition.
Avoid to deadlock such threads by correctly awakening the sleeping ones
after the pip is finished.
swapoff side of the bug can likely result in shutdown deadlocks.
Sponsored by: EMC / Isilon Storage Division
Reported by: pho, pluknet
Tested by: pho
- More flexible cluster size selection, including the ability to fall
back to a safe cluster size (PAGE_SIZE from zone_jumbop by default) in
case an allocation of a larger size fails.
- A single get_fl_payload() function that assembles the payload into an
mbuf chain for any kind of freelist. This replaces two variants: one
for freelists with buffer packing enabled and another for those without.
- Buffer packing with any sized cluster. It was limited to 4K clusters
only before this change.
- Enable buffer packing for TOE rx queues as well.
- Statistics and tunables to go with all these changes. The driver's
man page will be updated separately.
MFC after: 5 weeks
mbuf should be owned by if_transmit function in any case.
Submitted-by: Andrew Rybchenko <Andrew.Rybchenko at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
controller initialization.
The spec says OS drivers should send this command after controller
initialization completes successfully, but other NVMe OS drivers are
not sending this command. This change will therefore reduce differences
between the FreeBSD and other OS drivers.
Sponsored by: Intel
MFC after: 3 days
Replace usage of db_active in Xen console with kdb_active.
Reported by: Andrzej Tobola <ato@iem.pw.edu.pl>
Approved by: gibbs
Sponsored by: Citrix Systems R&D
As a prerequisite for multiple queues, the guest must have MSIX enabled.
Unfortunately, to work around device passthrough bugs, FreeBSD disables
MSIX when running as a VMWare guest due to the hw.pci.honor_msi_blacklist
tunable; this tunable must be disabled for multiple queues.
Also included is various minor changes from the projects/vmxnet branch.
MFC after: 1 month
further refinement is required as some device drivers intended to be
portable over FreeBSD versions rely on __FreeBSD_version to decide whether
to include capability.h.
MFC after: 3 weeks
Add support for MSI interrupts in the puc(9) driver. By default the driver
will prefer MSI interrupts to legacy interrupts. A tunable,
hw.puc.msi_disable, has been added to force the allocation of legacy
interrupts.
Reviewed by: jhb@
MFC after: 2 weeks
Sponsored by: Sandvine Inc.
interface, in the r241616 a crutch was provided. It didn't work well, and
finally we decided that it is time to break ABI and simply make if_baudrate
a 64-bit value. Meanwhile, the entire struct if_data was reviewed.
o Remove the if_baudrate_pf crutch.
o Make all fields of struct if_data fixed machine independent size. The
notion of data (packet counters, etc) are by no means MD. And it is a
bug that on amd64 we've got a 64-bit counters, while on i386 32-bit,
which at modern speeds overflow within a second.
This also removes quite a lot of COMPAT_FREEBSD32 code.
o Give 16 bit for the ifi_datalen field. This field was provided to
make future changes to if_data less ABI breaking. Unfortunately the
8 bit size of it had effectively limited sizeof if_data to 256 bytes.
o Give 32 bits to ifi_mtu and ifi_metric.
o Give 64 bits to the rest of fields, since they are counters.
__FreeBSD_version bumped.
Discussed with: emax
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
When running as a PVH guest, there's no emulated i8254, so we need to
use the Xen PV timer as the early source for DELAY. This change allows
for different implementations of the early DELAY function and
implements a Xen variant for it.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
dev/xen/timer/timer.c:
dev/xen/timer/timer.h:
- Implement Xen early delay functions using the PV timer and declare
them.
x86/include/init.h:
- Add hooks for early clock source initialization and early delay
functions.
i386/i386/machdep.c:
pc98/pc98/machdep.c:
amd64/amd64/machdep.c:
- Set early delay hooks to use the i8254 on bare metal.
- Use clock_init (that will in turn make use of init_ops) to
initialize the early clock source.
amd64/include/clock.h:
i386/include/clock.h:
- Declare i8254_delay and clock_init.
i386/xen/clock.c:
- Rename DELAY to i8254_delay.
x86/isa/clock.c:
- Introduce clock_init that will take care of initializing the early
clock by making use of the init_ops hooks.
- Move non ISA related delay functions to the newly introduced delay
file.
x86/x86/delay.c:
- Add moved delay related functions.
- Implement generic DELAY function that will use the init_ops hooks.
x86/xen/pv.c:
- Set PVH hooks for the early delay related functions in init_ops.
conf/files.amd64:
conf/files.i386:
conf/files.pc98:
- Add delay.c to the kernel build.
This should not introduce any functional change, and makes the
functions suitable to be called before we have actually mapped the
vcpu_info struct on a per-cpu basis.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
dev/xen/timer/timer.c:
- Remove citrical_{enter/exit}, the clock code will already be called
with preemption disabled when needed. Add a comment to that regard
in xentimer_get_timecount.
- Allow xen_fetch_vcpu_time to be called with a specifc vcpu_info
that will be used to fetch current time.
- Assert that xentimer_et_start will always be called with preemption
disabled.
This adds and enables the PV console used on XEN kernels to
GENERIC/XENHVM kernels in order for it to be used on PVH.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
dev/xen/console/console.c:
- Define console_page.
- Move xc_printf debug function from i386 XEN code to generic console
code.
- Rework xc_printf.
- Use xen_initial_domain instead of open-coded checks for Dom0.
- Gate the attach of the PV console to PV(H) guests.
dev/xen/console/xencons_ring.c:
- Allow the PV Xen console to output earlier by directly signaling
the event channel in start_info if the event channel is not yet
initialized.
- Use HYPERVISOR_start_info instead of xen_start_info.
i386/include/xen/xen-os.h:
- Remove prototype for xc_printf since it's now declared in global
xen-os.h
i386/xen/xen_machdep.c:
- Remove previous version of xc_printf.
- Remove definition of console_page (now it's defined in the console
itself).
- Fix some printf formatting errors.
x86/xen/pv.c:
- Add some early boot debug messages using xc_printf.
- Set console_page based on the value passed in start_info.
xen/xen-os.h:
- Declare console_page and add prototype for xc_printf.
baudrate of the device special file, and makes sure that on open(2) the
UART is programmed with the correct baudrate. This then eliminates the
need in uart_tty_param() to override the speed setting.
private per-chip HAL.
This allows the ah_osdep.[ch] code to check whether the power state is
valid for doing chip programming.
It should be a no-op for normal driver work but it does require a
clean kernel/module rebuild, as the size of HAL structures have changed.
Now, this doesn't track whether the hardware is ACTUALLY awake,
as NETWORK_SLEEP wakes the chip up for a short period when traffic
is received. This doesn't actually set the power mode to AWAKE, so
we have to be careful about how we touch things.
But it's enough to start down the path of implementing station mode
chipset power savings, as a large part of the silliness is making
sure the chip is awake during periodic calibration / ANI and
random places where transmit may be occuring. I'd rather not a repeat
of debugging power save on ath9k, where races with calibration
and transmit path stuff took a couple years to shake out.
Tested:
* AR5416, STA mode
This fixes kernel panic during boot, caused by incompatibility of recent
CAM locking changes and this bus scanner code.
Submitted by: Microsoft
MFC after: 1 week
Centrino 2230 firmware.
This fixes the general statistics block to be actually valid.
I've verified this by contrasting the output of iwnstats before and
after the change. The general block is now correct.
Tested:
* Intel 5100 (old format stats message)
* Intel 2230 (new format stats message)
(pvid=1) and we already configure them to send to other ports.
Setting pvid=portnum would mean that there were separate vlangroups
for each ports, but 'leaking' into other ports. The result? All port
traffic flooded to all other port traffic.
Tested:
* DB120, AR9344 + AR8327 switch
The OpenWRT AR8xxx switch support flushes the ATU (address translation
unit) after each port link 'up' status change. I've modified this to
just flush on any port transition.
Whilst here, bump the number of ports on the AR8327 to 6, rather than
the default of 5. It's DB120 specific; I'll go and make this configurable
later.
There's some debugging code in here still; I am still debugging whether
this is or isn't working fully.
Tested:
* DB120, AR9344 + AR8327 switch
Obtained from: OpenWRT
This patch does four things:
* it globally disables mirroring;
* it globally sets the mirroring on each port to be disabled;
* the initial port setup now programs a portmask for the port to allow
transmission (forwarding) to all other ports bar itself;
* the vlan setup path now programs the portmask for the port to
allow transmission (forwarding) to all other ports bar itself.
Before this, I hard-coded the portmask to 0x3f which would mean all
ports (bar port 6, which currently isn't hooked up to anything.)
This means that traffic would be duplicated back out the port it
received it. I bet this wasn't .. optimal.
In any case, this _seems_ to make DHCP from my macosx laptop
work through this access point. I'll do some further testing
to ensure it's actually working correctly on all my devices.
Tested:
* DB120, AR8327 switch
It turns out that there's a variant format of the RX statisitcs notification
from the intel firmware. It's even more whacked - the non-BT variant has
bluetooth fields; apparently some later NICs return even _more_ bluetooth
related fields.
I'll commit the statistics structure changes here - it's a no-op for the
driver. I'll later teach the driver code to populate a statistics structure
from the received message after reformatting things correctly.
I don't _think_ it's going to fix anything related to sensitivity programming
as the CCK/OFDM (non-11n) fields are in the same place for both formats.
But the HT structure and the general statistics aren't in the same place.
I'll go find some NIC(s) that spit out the other format and when I find one,
I'll go and update the driver to handle things correctly.
Tested:
* Intel 5100 (which returns the legacy, non-BT format)
Obtained from: Linux iwlwifi
match the device. Pinctrl will need to be added before this will work,
in addition to migrating the current board_foo.c method of configuring
these pins to something else. Non-FDT systems won't be affected, yet.
In my specific case, this fixes the problem of my PowerMac G5 displaying a
4:3 console on a 16:10 display with black bars on the left and right.
PR: kern/180558
Reviewed by: nwhitehorn
MFC after: 5 days
1) Add support for page back/forward.
2) While doing HOR scrolling, disable VER scrolling.
3) Checking dx_sum and dy_sum before emulate right button, this can
avoids unexpected right button press.
4) Fix stable pointer operation when emulating middle button.
Submitted by: Huang Wen Hui <huanghwh@gmail.com>
MFC after: 2 weeks
It's still hardcoded (for db120) but it is now hardcoded in all the
same place (ie, the pdata path.) The port config/status code now checks
port0/port6 as appropriate to configure things.
Tested:
* Qualcomm Atheros DB120, AR8327 switch.
This is (almost!) enough to actually probe, attach, configure a default
port group and do some basic work. It's also totally hard-coded for
the Qualcomm Atheros DB120 board - it doesn't yet have any of the code
from OpenWRT which parses extra configuration data to know how to program
the switch. The LED stuff is also missing.
But, it's enough to facilitate board, PHY, switch and VLAN bringup,
so I am committing it now.
Tested:
* Qualcomm Atheros DB120
Obtained from: OpenWRT
switches.
* Add some new VLAN HAL methods that will be used by the VLAN configuration
code. The AR933x and later switches use slightly different register
layouts (even though the driver currently doesn't support it.)
- Support for double-tap and drag.
- Support for 2-finger horizontal scrolling which translates to page-back/forward events.
- Single finger tap is equivalent to a left-button press.
- Two-finger taps are mapped to the right-button click.
- Three fingers are mapped to middle button.
- Add sysctl to disable single finger tapping.
- Fix for multiple open of /dev/atp0
- Enhanced support for the Fountain/Geyser family by adding Geyser4.
- Update manual page.
Submitted by: Rohit Grover <rgrover1@gmail.com>
MFC after: 2 weeks
HAL methods.
This allows the AR8327 code to override it as appropriate.
Tested:
* DB120 - AR8327 and AR9340 on-board switch; only running 'etherswitchcfg'
to check configs. The actual VLAN programming wasn't tested.
The registers (and perhaps the flags) are different for the AR8327, so
I'll stub those out until they're written.
Tested:
* DB120 - both on-chip AR9340 and AR8327 switches.
a single port to setup.
This may end up later being used as part of some logic to program
the PHY for a single port, rather than having to reinitialise them
all at once.
Tested:
* DB120
- intercept FIONBIO and FIOASYNC ioctls on netmap file descriptors.
libpcap calls them to set non blocking I/O on the file descriptor,
for netmap this is a no-op because there is no read/write,
but not intercepting would cause fcntl() to return -1
- rate limit and put under netmap.verbose some messages that occur
when threads use concurrently the same file descriptor.
Before this patch, curvnet was NULL.
When the VIMAGE kernel option is enabled, this eliminates
kernel panics when USB ethernet devices are plugged in.
PR: 183835
Submitted by: Hiroo Oono <hiroo.ono at gmail dot com>
about uss820dci_odevd being unused, by adding it to the part that
handles getting descriptors.
Reported by: loos
Reviewed by: hselasky
MFC after: 3 days
rather than SDHCI_RESET_ALL; the latter turns off clocks and power, removing
any possibility of recovering from the error.
Also, double the timeout to 2 seconds. Despite what the SD spec says about
all transactions completing in 250ms or less, I have a card which sometimes
takes more than a second to complete a write.
matching 'compatible' property. This probably has a short half-life (as
do most of the fdt_ functions), but it helps solve some near-term needs
until we work out the larger problems of device instantiation order
versus the order of things in the fdt data.
If the hardware is not in a good state (like maybe clocks aren't running
because of a configuration glitch) its timeout clock may also not work
correctly, and the next command sent will hang that thread forever. The
thread in question is usually the one and only thread (at init time) or
a bio queue worker thread whose lockup will eventually lead to the whole
system locking up when it runs out of buffers.
No sd card command should take longer than 250ms. This new code establishes
a 1-second timeout to allow plenty of safety margin over that.
Normally it never needs to wait here at all; waiting is done at the end
of the prior command. When doing a crash dump, the normal interrupt
mechanism isn't used; instead the interrupt handler is called repeatedly
in a polling-like manner. This can subvert hardware-specific drivers
and lead to trying to start a new command while the previous command is
still busy on the bus. Since the SD spec says the longest a card can
take to execute any command is 250ms, use that as a timeout.
- netmap pipes, providing bidirectional blocking I/O while moving
100+ Mpps between processes using shared memory channels
(no mistake: over one hundred million. But mind you, i said
*moving* not *processing*);
- kqueue support (BHyVe needs it);
- improved user library. Just the interface name lets you select a NIC,
host port, VALE switch port, netmap pipe, and individual queues.
The upcoming netmap-enabled libpcap will use this feature.
- optional extra buffers associated to netmap ports, for applications
that need to buffer data yet don't want to make copies.
- segmentation offloading for the VALE switch, useful between VMs.
and a number of bug fixes and performance improvements.
My colleagues Giuseppe Lettieri and Vincenzo Maffione did a substantial
amount of work on these features so we owe them a big thanks.
There are some external repositories that can be of interest:
https://code.google.com/p/netmap
our public repository for netmap/VALE code, including
linux versions and other stuff that does not belong here,
such as python bindings.
https://code.google.com/p/netmap-libpcap
a clone of the libpcap repository with netmap support.
With this any libpcap client has access to most netmap
feature with no recompilation. E.g. tcpdump can filter
packets at 10-15 Mpps.
https://code.google.com/p/netmap-ipfw
a userspace version of ipfw+dummynet which uses netmap
to send/receive packets. Speed is up in the 7-10 Mpps
range per core for simple rulesets.
Both netmap-libpcap and netmap-ipfw will be merged upstream at some
point, but while this happens it is useful to have access to them.
And yes, this code will be merged soon. It is infinitely better
than the version currently in 10 and 9.
MFC after: 3 days
This change makes ofw_iicbus attach to iicbb(4) controllers in addition to
the already supported i2c host bridges (iichb).
On iicbb(4) allow the direct access of the OFW parent node by its children,
so they can be directly attached to iicbb(4) node on the DTS without the
need of describing the i2c bus.
Approved by: adrian (mentor, implicit)
gpioled(4).
Tested on RPi and BBB (using the hardware I2C controller and gpioiic(4) for
the I2C tests). It was also verified for regressions on RSPRO (MIPS/ar71xx)
used as reference for a non OFW-based system.
Update the gpioled(4) and gpioiic(4) man pages with some details and
examples about the FDT/OFW support.
Some compatibility details pointed out by imp@ will follow in subsequent
commits.
Approved by: adrian (mentor, implicit)
describe GPIO bindings in the system.
Move the GPIOBUS lock macros to gpiobusvar.h as they are now shared between
the OFW and the non OFW versions of GPIO bus.
Export gpiobus_print_pins() so it can also be used on the OFW GPIO bus.
Approved by: adrian (mentor, implicit)
- Get USB input report length from HID descriptor.
- Use 1 finger TAP for devices which has no integrated button.
- Move data buffer to softc instead of allocating it.
MFC after: 1 week
should fix DMA descriptor caching issues seen with the EHCI controller
found in Google Chromebook C720 during removal and insertion of USB
devices.
MFC after: 1 week
Reported by: Matthew Dillon at DragonFlyBSD
I/O windows, the default is to preserve the firmware-assigned resources.
PCI bus numbers are only managed if NEW_PCIB is enabled and the architecture
defines a PCI_RES_BUS resource type.
- Add a helper API to create top-level PCI bus resource managers for each
PCI domain/segment. Host-PCI bridge drivers use this API to allocate
bus numbers from their associated domain.
- Change the PCI bus and CardBus drivers to allocate a bus resource for
their bus number from the parent PCI bridge device.
- Change the PCI-PCI and PCI-CardBus bridge drivers to allocate the
full range of bus numbers from secbus to subbus from their parent bridge.
The drivers also always program their primary bus register. The bridge
drivers also support growing their bus range by extending the bus resource
and updating subbus to match the larger range.
- Add support for managing PCI bus resources to the Host-PCI bridge drivers
used for amd64 and i386 (acpi_pcib, mptable_pcib, legacy_pcib, and qpi_pcib).
- Define a PCI_RES_BUS resource type for amd64 and i386.
Reviewed by: imp
MFC after: 1 month
hw.cxgbe.rsrv_noflow. When set, queue 0 of the port is reserved for
TX packets without a flowid. The hash value of packets with a flowid
is bumped up by 1. The intent is to provide a private queue for
link-level packets like LACP that is unlikely to overflow or suffer
deep queue latency.
Reviewed by: np
Obtained from: Netflix
MFC after: 3 days
Useful for so-called USB tethering.
- Imported code from OpenBSD
- Adapted code to FreeBSD
- Removed some unused functions
- Fixed some buffer encoding and decoding issues
- Optimised data transport path a bit, by sending multiple packets at a time
- Increased receive buffer to 16K
Obtained from: OpenBSD
Requested by: eadler @
MFC after: 2 weeks
9341-4i controller was to ensure that scatter/gather lists are ended with
an end-of-list marker. Both the mrsas and Linux megaraid_sas drivers use
this marker with Invader cards as well, so we do the same thing, though
it is apparently not strictly necessary.
Reviewed by: ambrisko
Tested by: ambrisko (Invader card)
MFC after: 3 weeks
Sponsored by: Sandvine Inc.
driver as version 8.037.00 for RTL8168{E-VL,EP,F,G,GU} and RTL8111B. This
makes reception of packets work with the RTL8168G (HW rev. 0x4c000000) in
my Shuttle DS47.
- Consistently use RL_MSI_MESSAGES.
In joint forces with: yongari
MFC after: 5 days
are mostly useful for debugging.
- hw.pci.clear_bars ignores all firmware-assigned ranges for BARs when
set.
- hw.pci.clear_pcib ignores all firmware-assigned ranges for PCI-PCI
bridge I/O windows when set.
MFC after: 1 week
Delaying isp_reqodx update, we should be ready to update it every time
we read it. Otherwise requests using several indexes may be requeued
ndefinitely without ever updating the variable.
MFC after: 3 days
a sub-node of nexus (ofwbus) rather than direct attach under nexus. This
fixes FDT on x86 and will make coexistence with ACPI on ARM systems easier.
SPARC is unchanged.
Reviewed by: imp, ian
allow mrsas(4) from LSI to attach to newer LSI cards that are support by
mrsas(4). If mrsas(4) is not loaded into the system at boot then mfi(4)
will always attach. If a modified mrsas(4) is loaded in the system. That
modification is return "-30" in it's probe since that is between
BUS_PROBE_DEFAULT and BUS_PROBE_LOW_PRIORITY.
This option is controller by a new probe flag "MFI_FLAGS_MRSAS" in mfi_ident
that denotes cards that should work with mrsas(4). New entries that should
have this option.
This is the first step to get mrsas(4) checked into FreeBSD and to avoid
collision with people that use mrsas(4) from LSI. Since mfi(4) takes
priority, then mrsas(4) users need to rebuild GENERIC. Using the
.disabled="1" method doesn't work since that blocks attaching and the
probe gave it to mfi(4).
Discussed with: LSI (Kashyap Desai)
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
process "status" properties of OF nodes.
I've avoided adding new KOBJ methods here so that we don't have to modify
every ofw_bus in the tree. Since 100% of implementations of ofw_bus use
only ofw_bus_gen_*(), it might be worth garbage-collecting the other
methods as well.
The sglist segment array has grown to a bit over 512 bytes (on
64-bit system) which is more than ideally should be put on the
stack. Instead allocate an appropriately sized sglist and hang
it off each Rx/Tx queue structure.
Bump the maximum number of Tx segments to 64 to make it unlikely
we'll have defragment an mbuf chain. Our previous count was
rounded up to this value since it is the next power of two, so
effective memory usage should not change.
Also only allocate the maximum number of Tx segments if TSO was
negotiated.
get the Routerboard 800 up and running with the vendor device tree. This
does not implement some BERI-specific features (which hopefully won't be
necessary soon), so move the old code to mips/beri, with a higher attach
priority when built, until MIPS interrupt domain support is rearranged.
strings and include arbitrary information (IRQ line/domain/sense). When the
ofw_bus_map_intr() API was introduced, it assumed that, as on most systems,
these were either 1 cell, containing an interrupt line, or 2, containing
a line number plus a sense code. It turns out a non-negligible number of
ARM systems use 3 (or even 4!) cells for interrupts, so make this more
general.
This also fixes asserts on removal of the module for the mpc74xx.
The PowerPC 970 processors have two different types of events: direct events
and indirect events. Thus far only direct events are supported. I included
some documentation in the driver on how indirect events work, but support is
for the future.
MFC after: 1 month
r261266:
Add a jail parameter, allow.kmem, which lets jailed processes access
/dev/kmem and related devices (i.e. grants PRIV_IO and PRIV_KMEM_WRITE).
This in conjunction with changing the drm driver's permission check from
PRIV_DRIVER to PRIV_KMEM_WRITE will allow a jailed Xorg server.
/dev/kmem and related devices (i.e. grants PRIV_IO and PRIV_KMEM_WRITE).
This in conjunction with changing the drm driver's permission check from
PRIV_DRIVER to PRIV_KMEM_WRITE will allow a jailed Xorg server.
Submitted by: netchild
MFC after: 1 week
- Use system provided functions for HID report requests.
- Nice the mode setting, because the USB hardware does appear to
handle the commands right away.
MFC after: 1 week
the memory ranges that they decode for downstream devices rather than
creating ResourceProducer range resource entries. The result is that
we allocate the full range to the PCI root bridge device causing
allocations in child devices to all fail.
As a workaround, ignore any standard memory resources on a PCI root
bridge device. It is normal for a PCI root bridge to allocate an I/O
resource for the I/O ports used for PCI config access, but I have not
seen any PCI root bridges that legitimately allocate a memory resource.
Reviewed by: jkim
MFC after: 1 week
that all pressed keys are released before completing the USB keyboard
detach. This will prevent so-called "ghost-keys" from appearing after
that the USB device generating the key event(s) has been detached.
MFC after: 1 week
when activating an I/O or memory window on the CardBus bridge.
Tested by: Olivier Cochard-Labbe <olivier@cochard.me>
Reviewed by: imp
MFC after: 3 days
a timeout value of a single tick is given. With FreeBSD-10 and newer
the current system time is used as a starting point, and the minimum
callout time of a single tick will be guaranteed. This patch mostly
affect the DMA delay timeouts, which are typically in the range from
0.125 to 2ms.
MFC after: 1 week
- Store the length of each read-only VPD value since not all values are
guaranteed to be ASCII values (though most are).
- Add a new pciio ioctl to fetch VPD for a single PCI device. The values
are returned as a list of variable length records, one for the device
name and each keyword.
- Add a new -V flag to pciconf's list mode which displays VPD data for
each device.
MFC after: 1 week
console, it calls the grab functions. These functions should turn off
the RX interrupts, and any others that interfere. This makes mountroot
prompt work again. If there's more generalized need other than
prompting, many of these routines should be expanded to do those new
things.
Should have been part of r260889, but waasn't due to command line typo.
Reviewed by: bde (with reservations)
with USB device detach when using character device handles. This also
includes LibUSB. It turns out that "usb_close()" cannot always get a
reference to clean up its USB transfers and such, if called during the
kernel USB device detach.
Analysis by: hselasky @
Reported by: Juergen Lock <nox@jelal.kn-bremen.de>
MFC after: 1 week
add separate rx/tx ring indexes
add ring specifier in nm_open device name
netmap.c, netmap_vale.c
more consistent errno numbers
netmap_generic.c
correctly handle failure in registering interfaces.
tools/tools/netmap/
massive cleanup of the example programs
(a lot of common code is now in netmap_user.h.)
nm_util.[ch] are going away soon.
pcap.c will also go when i commit the native netmap support for libpcap.
non-modifier key press. This prevents so-called "ghost
keyboards" keeping modifier keys pressed while not
actually seen as a real keyboard.
MFC after: 2 weeks
found in High Speed USB HUBs which translate from High Speed USB into
FULL or LOW speed USB. In some rare cases SPLIT transactions might get
lost, which might leave the TT in an unknown state. Whenever we detect
such an error try to issue either a clear TT buffer request, or if
that is not possible reset the whole TT.
MFC after: 1 week
controller found in the MBP2013 has been observed to not work properly
unless this operation is performed.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
make CAM to not try negotiate unsupported settings and suppress warnings.
While there, enable command queuing on pass-through devices, announced
in hba_inquiry, but disabled. Even though queue size is very small, It
seems working well enough.
Reviewed by: scottl
MFC after: 2 weeks
The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
Remove old bits of data concat for 'ascii' field.
Remove special SIOCGIFSTATUS handling from if.c (which Coverity yells at).
Reported by: Coverity
Coverity CID: 1147174
MFC after: 2 weeks
WARNING: icl_pdu_check_data_digest: data digest check failed; got 0xf23b,
should be 0xdb7f23b
Tested by: Darcy Birkbeck
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
value. The "Intel Lynx Point" XHCI controller found in the MBP2013 has
been observed to not always set the event interrupt bit while there
are events to consume in the event ring.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
the spoofed identify data into the user buffer rather than issuing the
command to the controller, since Chatham IDENTIFY data is always spoofed.
While here, fix a bug in the spoofed data for Chatham submission and
completion queue entry sizes.
Sponsored by: Intel
MFC after: 3 days
Most relevant features:
- netmap emulation on any NIC, even those without native netmap support.
On the ixgbe we have measured about 4Mpps/core/queue in this mode,
which is still a lot more than with sockets/bpf.
- seamless interconnection of VALE switch, NICs and host stack.
If you disable accelerations on your NIC (say em0)
ifconfig em0 -txcsum -txcsum
you can use the VALE switch to connect the NIC and the host stack:
vale-ctl -h valeXX:em0
allowing sharing the NIC with other netmap clients.
- THE USER API HAS SLIGHTLY CHANGED (head/cur/tail pointers
instead of pointers/count as before). This was unavoidable to support,
in the future, multiple threads operating on the same rings.
Netmap clients require very small source code changes to compile again.
On the plus side, the new API should be easier to understand
and the internals are a lot simpler.
The manual page has been updated extensively to reflect the current
features and give some examples.
This is the result of work of several people including Giuseppe Lettieri,
Vincenzo Maffione, Michio Honda and myself, and has been financially
supported by EU projects CHANGE and OPENLAB, from NetApp University
Research Fund, NEC, and of course the Universita` di Pisa.
freeing them.
The current code would walk the list and call the buffer free, which
didn't remove it from any lists before pushing it back on the free list.
Tested: AR9485, STA mode
Noticed by: dillon@apollo.dragonflybsd.org
related to setting up static device mappings. Since it was only used by
arm/mv/mv_pci.c, it's now just static functions within that file, plus
one public function that gets called only from arm/mv/mv_machdep.c.
obsolete. This involves the following pieces:
- Remove it entirely on PowerPC, where it is not used by MD code either
- Remove all references to machine/fdt.h in non-architecture-specific code
(aside from uart_cpu_fdt.c, shared by ARM and MIPS, and so is somewhat
non-arch-specific).
- Fix code relying on header pollution from machine/fdt.h includes
- Legacy fdtbus.c (still used on x86 FDT systems) now passes resource
requests to its parent (nexus). This allows x86 FDT devices to allocate
both memory and IO requests and removes the last notionally MI use of
fdtbus_bs_tag.
- On those architectures that retain a machine/fdt.h, unused bits like
FDT_MAP_IRQ and FDT_INTR_MAX have been removed.
static device mappings.
This SoC relied heavily on the fact that all devices were static-mapped
at a fixed address, and it (rather bogusly) used bus_space read and write
calls passing hard-coded virtual addresses instead of proper bus handles,
relying on the fact that the virtual addresses of the mappings were known
at compile time, and relying on the implementation details of arm
bus_space never changing. All such usage was replaced with calls to
bus_space_map() to obtain a proper bus handle for the read/write calls.
This required adjusting some of the #define values that map out hardware
registers, and some of them were renamed in the process to make it clear
which were defining absolute physical addresses and which were defining
offsets. (The ones that just define offsets don't appear to be referenced
and probably serve no value other than perhaps documentation.)
Using unmapped BIOs causes failure inside bus_dmamap_sync, since
this function requires valid MVA address, which is not present
if mapping is not set up.
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Atmel boards I have.
# All Samsung, Toshiba and SanDisk parts will need to be in this table
# since they don't conform to the ONFI specification (they are all Toggle
# parts). There's some standards for the additional bytes so there's some hope
# to decode them automatically on a per-vendor basis, but even that has
# problems (and is what motivated the ONFI parameter page).
header is split out into its own BD for processing by the firmware. When
this split occurred the data length in the BD was not being set correctly
resulting in packet corruption.
Approved by: davidcd (mentor)
by receive code waiting for data digest even when the data segment was
empty. It didn't actually read it, but it waited until those four bytes
become available in the socket buffer, i.e. until any other PDU (such as NOP)
came in.
PR: kern/185240
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Quiesce the interrupt before actually detaching.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Nuke dupe $FreeBSD$.
MFC after: 1 week
hw.ral.msi_disable (defaulting to using MSI).
- Probe with BUS_PROBE_DEFAULT instead of 0.
- Nuke code setting PCI_POWERSTATE_D0; pci(4) already does that for type 0
devices.
- Use PCIR_BAR instead of a homegrown macro.
- There's no need to keep track of resource IDs.
- Release resources again in case attaching fails.
- Quiesce the interrupt before detaching.
- Sprinkle const.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Trim headers.
- Nuke dupe $FreeBSD$.
MFC after: 1 week
- #if 0 the currently unused paired port linking and unlinking of dual
adapters.
- Simplify MSI/MSI-X allocation and release. For a single one, we don't need
to fiddle with the MSI/MSI-X count and pci_release_msi(9) is smart enough
to just do nothing in case of INTx.
- Canonicalize actions taken on attach failure and detach.
- Remove the remainder of incomplete support for older FreeBSD versions.
MFC after: 1 week
- Simplify MSI allocation and release. For a single one, we don't need to
fiddle with the MSI count and pci_release_msi(9) is smart enough to just
do nothing in case of INTx.
- Don't allocate MSI as RF_SHAREABLE.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
- Based on lessons learnt with dc(4) (see r185750), add bus space barriers to
the MII bitbang read and write functions as well as to instances of page
switching.
- Add missing locking to ed_ifmedia_{upd,sts}().
- Canonicalize some messages.
- Based on actual functionality, ED_TC5299J_MII_DIROUT should be rather named
ED_TC5299J_MII_DIRIN.
- Remove unused headers.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 1 week
fiddle with the MSI count and pci_release_msi(9) is smart enough to just
do nothing in case of INTx.
- Don't allocate MSI as RF_SHAREABLE.
MFC after: 1 week
better off living in aac_pci.c, but it doesn't seem worth creating a
aac_pci_detach() and it's also not the first PCI-specific bit in aac.c
MFC after: 3 days
This chip doesn't require the temperature sensor offset, either v1 or
v2. Doing so causes the initial calibration test to fail.
Tested:
* Intel Centrino 6150
by removing unsued file local functions and then unused callees.
A lot more warnings to resolve but someone had to break the ice.
MFC after: 10 days
X-Comment: I am not the new maintainer; chime in, it's ours.
o Forward termianl framebuffer ioctl to fbd.
o Forward terminal mmap request to fbd.
o Move inclusion of sys/conf.h to vt.h.
Sponsored by: The FreeBSD Foundation
The priority goes from "error" to "debug".
Connectors are polled every 10 seconds. Reading EDID is part of this
polling. However, when an invalid EDID is returned, this error message
is logged. When using Newcons for instance, having a kernel message
every 10 seconds is getting annoying.
Now that it's a debug message, it'll be logged only if hw.dri.debug is
enabled. This fix console spamming for some users.
Tested by: Larry Rosenman <ler@lerctr.org>
clients. Mask RX interrupts while grabbed on the atmel serial
driver. This UART interrupts every character. When interrupts are
enabled at the mountroot> prompt, this means the ISR eats the
characters. Rather than try to create a cooperative buffering system
for the low level kernel console, instead just mask out the ISR. For
NS8250 and decsendents this isn't needed, since interrupts only happen
after 14 or more characters (depending on the fifo settings). Plumb
such that these are optional so there's no change in behavior for all
the other UART clients. ddb worked on this platform because all
interrupts were disabled while it was running, so this problem wasn't
noticed. The mountroot> issue has been around for a very very long
time.
MFC after: 3 days
... for msleep/cv_*wait() return values, where wait_event*() is used
on Linux. ERESTARTSYS is the return code expected by callers when the
operation was interrupted.
For instance, this is the case of radeon_cs_ioctl() (radeon_cs.c): if
an error occurs, and the code isn't ERESTARTSYS (eg. EINTR), it logs an
error.
Note that ERESTARTSYS is defined as ERESTART, but this keeps callers'
code close to Linux.
Submitted by: avg@ (previous version)
Normal and bold fonts each have a glyph map for single or left half-
glyphs, and right half glyphs. The flag TF_CJK_RIGHT in term_char_t
requests the right half-glyph.
Reviewed by: ed@
Sponsored by: The FreeBSD Foundation
The previous code was checking the "VGA Enable" bit on the video card's
parent PCI-to-PCI bridge only. This didn't work for the case where the
video card is attached to the root PCI bus (ie. the card has no parent
PCI-to-PCI bridge).
Now, the new code:
1. checks the "VGA Enable" bit on the parent bridge only if it's a
PCI-to-PCI bridge;
2. always checks the "I/O" and "Memory address space decoding" bits
on the video card itself.
However, vendor-specific bits are not used.
This fixes the use of many integrated Radeon cards: without this patch,
we fail to detect them as the boot display and, when radeonkms looks for
the Video BIOS, it skips the shadow copy made by the System BIOS. It
then fails to fully initialize the card, because the shadow copy is the
only way to read the Video BIOS in these situations. A workaround was to
force the boot display selection using the "hw.pci.default_vgapci_unit"
tunable.
A previous version of this patch added a new function doing the checks.
Now, the vga_pci_is_boot_display() function is used to perform the
checks (only until the boot display is found) and return if the given
device is the boot display or not.
Furthermore, vga_pci_attach() logs "Boot video device" if the card being
attached it the Chosen One:
vgapci0: <VGA-compatible display> [...]
vgapci0: Boot video device
Reviewed by: kib@, jhb@ (both a previous version)
Tested by: lunatic_ (#freebsd-xorg, integrated Radeon card,
xmj (#freebsd-xorg, i915+NVIDIA cards)
Introduce a new formatting bit (TF_CJK_RIGHT) that is set when putting a
cell that is the right part of a CJK fullwidth character. This will
allow drivers like vt(9) to support fullwidth characters properly.
emaste@ has a patch to extend vt(9)'s font handling to increase the
number of Unicode -> glyph maps from 2 ({normal,bold)} to 4
({normal,bold} x {left,right}). This will need to use this formatting
bit to determine whether to draw the left or right glyph.
Reviewed by: emaste
using cpuid can be quirky (this is the case of VMWare without the
vPMC support) but fail to probe hwpmc.
o Apply the fix for XEON family of processors as established by
315338-020 document (bug AJ85).
Sponsored by: EMC / Isilon storage division
Reviewed by: fabient
Previously the code would just iterate over the whole tree as if it were
just a list.
Without this change I would observe X server becoming more and more
jerky over time.
MFC after: 5 days
in6addr_any and is not in the CLIP table either. This fixes a reported
TOE+IPv6 NULL-dereference panic in do_pass_open_rpl().
While here, stop creating hardware servers for any loopback address.
It's just a waste of server tids.
MFC after: 1 week
Some Intel XHCI controlles timeout processing so-called "TRBs" when
the final LINK TRB of a so-called "TD" has the CHAIN-BIT set.
MFC after: 1 week
Tested by: glebius @
o Assign sc->an_dev in an_probe() (which isn't really a probe function in
the standard newbus sense) as we may need it for printing errors.
o Use device_printf() rather than if_printf() in an_reset() - this is
called from an_probe() long before the ifp structure is initialised
in an_attach().
o Initialize the ifp structure early in an_attach() as we use if_printf()
in cases where allocation of descriptors etc fails.
MFC after: 3 days
them up as part of firmware initialization (which the driver gets to do
only if it's the master driver).
Read the range of tids available for the ETHOFLD functionality if it's
enabled.
New is_ftid() and is_etid() functions to test whether a tid falls within
the range of filter tids or ETHOFLD tids respectively.
MFC after: 2 weeks
receiving Zero Length Packets, ZLPs. See comment in code for more
information.
MFC after: 1 week
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
sys/cdefs.h. In particular, in case of COMPAT_43, param.h includes
sys/types.h, which includes sys/select.h, which includes
sys/_sigset.h. The _sigset.h customizes the provided definions based
on COMPAT_43, eliminating osigset_t if symbol is not defined. The
sys/proc.h is included after opt_compat.h and needs osigset_t.
Move opt_compat.h inclusion into the right place.
Sponsored by: The FreeBSD Foundation
the bio is unmapped, so we must map the bio pages into pbuf. This
works around the geom classes which do not follow the MAXPHYS limit on
the i/o size, since such classes do not know about unmapped bios
either.
Reported by: Paolo Pinto <paolo.pinto@netasq.com>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
inclusion of right after sys/param.h.
o Only vt_core module use compat options, move it from common header to module.
Reported by: Larry Rosenman ler at lerctr dot org
Sponsored by: The FreeBSD Foundation
o Include opt_splash.h for vt(9) to know when splash device is enabled.
o Build logo_freebsd.c only if splash and vt are enabled.
o Include opt_compat.h to know when we have to respect compatibility.
Sponsored by: The FreeBSD Foundation
The code was unmodified compared to Linux and returned the amount of
received bytes from the i2c bus. This led to non-working i2c bus and
failure to eg. read monitor's EDID, if connected to DisplayPort.
MFC after: 3 days
Tested by: Mikaël Urankar <mikael.urankar@gmail.com>
This fixes radeon_agp_init() and gtt_size is now correct. However, this
is not enough to make Radeon AGP cards work: ttm_agp_backend.c isn't
implemented yet.
Submitted by: tijl@
Make the scan state optional - we'll obviously need a vap, but we now
won't require the scan state. the only thing the scan state is needed
for is to check for the list of SSIDs to scan - which we can now
just plain ignore by passing in NULL as the scan state pointer.
Tested:
* Intel 5100 (STA)
This is in preparation for being able to use iwn_scan() to do an off
channel scan to reset the RF tuning.
It should be a no-op.
Tested:
* Intel 5100 (STA)
in preparation for the scan based retune logic.
The linux iwlwifi driver does a rescan (onto a non-active channel)
to force an RF retune when the PLCP error rates exceed a certain threshold.
* Add code to track HT PLCP rate errors;
* Separate out the PLCP error count fetch and update so the delta
can be used when checking for PLCP error rates;
* Implement the PLCP error logic from iwlwifi;
* For now, just print out whenever the error rate exceeds the
threshold.
The actual scan based retune will take a bit more effort; the scan
command code right now assumes that a scan state is passed in.
This does need to change to be more flexible (both for this and
in preparation for scanning multiple channels at once.)
Tested:
* 5100 (STA mode)
* 2200 (STA mode)
* 2230 (STA mode)
working on some RF tuning issues.
The linux iwlwifi driver has these thresholds which they use to see
if there are PLCP errors over a certain interval. If they hit this,
they trigger a single-channel (different from active channels!)
scan to retune the RF front-end.
- Add support to 40Gbps devices;
- Add support to control adaptive interrupt coalescing (AIC)
via sysctl;
- Improve support of BE3 devices;
Many thanks to Emulex for their continued support of FreeBSD.
Submitted by: Venkata Duvvuru <VenkatKumar.Duvvuru Emulex Com>
MFC after: 3 days
scheduling classes in the chip and to bind tx queue(s) to a scheduling
class respectively. These can be used for various kinds of tx traffic
throttling (to force selected tx queues to drain at a fixed Kbps rate,
or a % of the port's total bandwidth, or at a fixed pps rate, etc.).
Obtained from: Chelsio
for these chipsets.
* Correctly set the active/passive flag in the scan request - this is
NOT a "is the channel active|passive"; it's to do with whether we
have an SSID to actively scan for or not. The firmware takes care
of the active/passive setup of the channel.
* Calculate the active/passive dwell time based on the beacon interval
and the channel mode, rather than using a hard coded value.
* For now, hardcode the scan service_time. It's defined as:
31:22 - number of beacon intervals to come back onto the home channel
for;
0:21 - time (microseconds) to come back onto the home channel for.
When doing an active scan when the NIC is active (whether we're associated
or not - it only matters if we've setup the NIC to a destination or not)
this determines how much time to stay on the home channel for when
scanning. We can tune this based on the amount of active traffic.
For now it's 4 beacon intervals and 100 microseconds.
* Fix the "good crc threshold" setting. It differs based on the NIC
firmware. Some older firmware required a workaround; the later
firmware instead treats the field as a flag.
* Enforce that we are not sending a scan command if one is already
pending. Any time this is done is a bug and it absolutely needs
to be fixed - so be very loud.
* Add the SCAN flag to a few debug messages that are scan related but
only occuring under STATE.
Now, this does get noisy when you're scanning in an actively busy 2GHz
network as the firmware (for reason I don't quite yet understand) seems
hell bent on staying on some passive channels longer than it should.
However, it should eventually recover and complete the scan.
This is a work in progress; please let me know if things get stuck or
if things improve!
Tested:
* intel centrino 2200
* intel centrino 2230
* intel 6200
* intel 5100
* intel 4965 (gets upset, but that's a known issue)
Obtained from: linux iwlwifi
TX ring according to what the firmware requires.
The firmware requires A-MPDU sub-frames to be at a very specific ring
offset - that is, the ring slot offset should be (seqno % 256.)
This holds for every NIC I've tested thus far except the 4965,
which starts erroring out here shortly before the firmware panics.
Which is good, it's doing what it's supposed to (read: capture that
we've screwed up somewhere.)
The specifics about getting this stuff right:
* the initial seqno allocation should match up with the ringid.
* .. yes, this means we can start at a ring offset that isn't zero.
* .. because we program the start seqno in the firmware message
to setup the AC.
* The initial seqno allocation may be non-zero _and_ frames may be
being transmitted during a-mpdu negotiation. I faced similar
issues on ath(4) and had to software queue frames to that node+TID
during A-MPDU negotiation.
* seqno allocation should be in lockstep with ring increments.
* If we fail to transmit some segment, no, we shouldn't reuse that
ring slot. We should just transmit a BAR (which we aren't yet
doing, sigh) and move onto the next seqno.
* In theory there shouldn't be any holes in the seqno space when
we are transmitting frames.
Tested:
* 4965 (throws problems, so yes we have to fix this);
* 5100 (seems ok);
* 6200 (seems ok);
* 2200 (seems ok);
* 2230 (seems ok).
The directory sys/dev/drm2/i915 is apperently contributed code.
Revert to the broken version of this file to make future imports easier.
Requested by: kib
in /chosen, be ihandles. The ePAPR spec makes those cross-reference phandles,
since FDT has no concept of ihandles. Have the OF FDT CI module interpret
queries about ihandles as cross-reference phandles.
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
In its stead use the Solaris / illumos approach of emulating '-' (dash)
in probe names with '__' (two consecutive underscores).
Reviewed by: markj
MFC after: 3 weeks
The code was easier to read without __DECONST and clang didn't report
any error. I thought the cast was enough...
MFC after: 3 days
X-MFC-With: r258549
drm_le_cmp() (qsort_r()'s callback) receives pointers to elements in the
array passed to qsort_r(), not the elements themselves.
Before this fix, the use of qsort_r() shuffled the array, not sorted it,
because the compare callback accessed random memory locations, not the
expected elements.
This bug triggered an infinite loop in KDE/xserver:
1. KDE has a kded module called "randrmonitor" which queries xserver
for current monitors at startup and then listens to RandR
notifications from xserver.
2. xserver handles the query from "randrmonitor" by polling the
video device using the "drm_mode_getconnector()" ioctl. This
ioctl returns a list of connectors and, for those with a
connected monitor, the available modes. Each modes list is sorted
by the kernel before returning. When xserver gets the connectors
list, it sorts the modes lists again.
In the case of this bug, when two modes are equal (in xserver's
compare function PoV), their order is kept stable (ie. the
kernel order is kept for those two modes). And because the list
was shuffled by the kernel, the order of two equal modes was
frequently changed in the final modes list in xserver.
3. xserver compares the returned connectors list with the list
obtained earlier. In particular, it compares the sorted
modes lists for each connector. If a property of a connector
changes (eg. modes), xserver sends a "RRNotify_OutputChange"
notification.
Because of the change of order between equal modes, xserver sent
a notification after each polling of the connectors.
4. "randrmonitor" receives a notification, triggered by its query. The
notification doesn't contain the new connectors list, therefore, it
asks for the new list using the same function: go back to step #2.
MFC after: 3 days
option, unbreak the lock tracing release semantic by embedding
calls to LOCKSTAT_PROFILE_RELEASE_LOCK() direclty in the inlined
version of the releasing functions for mutex, rwlock and sxlock.
Failing to do so skips the lockstat_probe_func invokation for
unlocking.
- As part of the LOCKSTAT support is inlined in mutex operation, for
kernel compiled without lock debugging options, potentially every
consumer must be compiled including opt_kdtrace.h.
Fix this by moving KDTRACE_HOOKS into opt_global.h and remove the
dependency by opt_kdtrace.h for all files, as now only KDTRACE_FRAMES
is linked there and it is only used as a compile-time stub [0].
[0] immediately shows some new bug as DTRACE-derived support for debug
in sfxge is broken and it was never really tested. As it was not
including correctly opt_kdtrace.h before it was never enabled so it
was kept broken for a while. Fix this by using a protection stub,
leaving sfxge driver authors the responsibility for fixing it
appropriately [1].
Sponsored by: EMC / Isilon storage division
Discussed with: rstone
[0] Reported by: rstone
[1] Discussed with: philip
big chunk of kernel memory. Validate size of data. Add error handling to
avoid calling copyout() when data has not been read correctly.
Reviewed by: zbb
Reported by: x90c <geinblues@gmail.com>
MFC after: 2 days
adapters. Both devices support Gigabit Ethernet and USB 2.0, and the AX88179
supports USB 3.0. The driver was written by kevlo@ and lwhsu@, with a few
bug fixes from me.
MFC after: 2 months
This fixes DPMS with KDE and radeonkms. Without this, the display would
freeze when the monitor is put into sleep state, and only resumes after
several dozens of minutes once the monitor is powered on again.
Tested by: Mathias Picker <Mathias.Picker@virtual-earth.de>
byte positions within the OOB area to support chips with unusual OOB
sizes such as 218 or 224 bytes.
The table for 128 byte OOB works for these but it assumes 3 bytes of ECC
per 256 byte block, and in the case of an ONFI chip the params page may
ask for something different. In other words, this is better but not
yet perfect.
to native endianness. We must also pay attention to unaligned accesses.
Copy the interesting parameters to a new struct so the rest of the code can
forget about these problems.
Submitted by: Kristof Provost <kristof@sigsegv.be> (cleanup) and me (orig).
The ONFI spec states that at least two bytes of the signature ("ONFI")
must be present, and the CRC must be correct to have a valid parameter
page. If the page is not valid there are at least two backup pages where
the data can also be found.
Submitted by: Kristof Provost <kristof@sigsegv.be> (cleanup) and me (orig).
Fixed various link related issues and 10GBaseT is now linking properly.
Modified the types for the driver tunables to be consistent with the sysctl APIs.
Approved by: davidch (mentor)
sys/dev/xen/balloon/balloon.c:
Remove unused and commented out code.
Fix deadlock caused by performing a sleepable malloc
while holding the balloon mutex.
Perform proper accounting of the memory used by the domain.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
MFC after: 2 days
struct mbx_common_read_write_flashrom plus 32KB and caps the actual
transfer size at 32KB. This is harmless as it is but may confuse
static code analyzer, so allocate a full 32KB instead.
Reported by: Coverity via mjacob
Submitted by: Venkata Duvvuru <VenkatKumar.Duvvuru Emulex Com>
Coverity CID: 1125820
This field needs to be (a) set, and (b) greater than the other timeouts
(passive, active, maxquiet, etc.) It also is in microseconds, not
milliseconds.
I hope this will fix the scan hangs that people are seeing.
Obtained from: Linux iwlwifi
The previous code simply hard-coded IWN_ANT_AB which is only correct for
some of the NICs.
Now, if the NIC is a 1-stream TX, you need to set IWN_ANT_AB and _not_
just a single antenna. The Intel 5100 firmware panics the moment the
link quality table is updated.
So!
* no secondary antenna? Set it to IWN_ANT_AB;
* two-stream device? Transmit on the full transmit antenna configuration.
Tested:
* Intel 5100, STA
* Intel 2200 (eadler)
Obtained from: Linux iwlwifi
it can be overriden by its OFW/FDT version.
Give a chance for GPIO devices that implement the device_identify method to
attach.
Approved by: adrian (mentor)
support.
* Extend the hardware base_params structure to include a bunch of hardware
flags indicating what is and isn't supported.
* Convert a bunch of the initial hardware configuration conditionals to
consult the base_params structure.
* Add new calibration code for temperature calibration for the Centrino 2xxx
series NICs.
* Add new bluetooth coexistence code for Centrino 2xxx series NICs.
* For NICs that support PAN (personal area networking), use a different
transmit queue and command queue setup, in preparation for said
PAN support.
* Extend the calibration array in iwn_softc to include enough space for
the new calibration types.
Tested (by myself, if not mentioned):
* Intel 4965
* Intel 5100
* Intel 6150
* Intel 2230
* Intel 2200 (eadler)
* Intel 1030
* Intel 6200
* Intel 6230
* Intel 6250
* Intel 6150
* Intel 100
What doesn't work:
* Intel 6235 - fails in calibration at startup
TODO:
* Testing on Intel 53xx series hardware
Submitted by: Cedric Gross <cg@cgross.info>
This is a terrible solution that at least behaves mostly correctly.
It walks the currently active rate table looking for rates to match.
It assumes that the code matches the setup path in the link quality
setup code (much like the previous, much simpler but even more hackish
math did.)
It's O(n), but n<15, so we're okay for the time being.
Tested:
* Intel 5100, STA - 11a, 11n, 11bg modes.
(which is a 1x2 device) panics the firmware.
But, for some 6xxx devices that require IWN_ANT_BC for the TX chainmask,
the link quality entries need to represent _that_.
So, revert this for now until I can figure out what is supposed to be
going on.
assumed that the MDIO bus was a direct child of the Ethernet interface. It
may not be and indeed on many device trees is not. While here, add proper
locking for MII transactions, which may be on a bus shared by several MACs.
Hardware donated by: Benjamin Perrault
NIC and pushed up to the driver. Unfortunately this means there's
no rate control notification done. Thus, if the rate control code
makes a decision that hits a crappy rate that can't succeed, the
rate code would never lower the rate and packet loss would continue.
So, fake some rate control notification in this case.
Without this, a far away station with low signal strength would
associate using the management rate (by default the lowest rate)
and then the EAPOL frames would go out at the current AMRR best
guess. This would result in association failing authentication.
Tested:
* Intel 5100, STA
* Intel 2230, STA
- Process ATIO queue only if interrupt status tells so;
- Do not update queue out pointers after each processed command, do it
only once at the end of the loop.
every time. The purpose of that register is unlikely output queue overflow
detection, so read it only when its last known (and probably stale now)
value signals overflow.
This reduces CPU load and lock congestion and rises bottleneck in CTL
while doing target mode via two 8Gbps ports from 100K to 120K IOPS.
This is a no-op for now!
* Add a new flag value for "there are no extra bits" for some random
field;
* Add a definition for the maximum number of calibration entries in
the calibration data cache in iwn_softc. It's not yet used.
* Add regulatory bands for the 2030 NIC.
Submitted by: Cedric Gross <cg@cgross.info>
makes FreeBSD halt but not poweroff (as expected when issuing a
shutdown from the VM manager). Fix this by using the same handler
for both "halt" and "poweroff".
NB: The "halt" signal seems to be used on XenServer only. The OSS
Xen toolstack (xl) uses "poweroff" instead.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
MFC after: 2 days
Full MSI-X interrupt support added.
Timeout and reset handling reworked, firmware flash update test added.
Support for drives with 4KB block size added.
Changes made to avoid exposure of phys. array components by default.
Approved by: scottl (mentor), emaste (co-mentor)
fdt_next_property_offset() API. The old code would sometimes (e.g. on
the device tree supplied by the RB800 boot loader) get confused and stop
partway through listing properties.
MFC after: 1 week
softc's "sc->sc_mtx" mutex. Currently the callout was marked
multi-processor safe, which is fine, but it is better to
start/stop/reset callouts while holding the "run" drivers own
mutex. While at it add a missing "ULL" at end of the 64-bit unsigned
integer constant.
MFC after: 1 week
fdtbus in most cases. This brings ARM and MIPS more in line with existing
Open Firmware platforms like sparc64 and powerpc, as well as preventing
double-enumeration of the OF tree on embedded PowerPC (first through nexus,
then through fdtbus).
This change is also designed to simplify resource management on FDT platforms
by letting there exist a platform-defined root bus resource_activate() call
instead of replying on fdtbus to do the right thing through fdt_bs_tag.
The OFW_BUS_MAP_INTR() and OFW_BUS_CONFIG_INTR() kobj methods are also
available to implement for similar purposes.
Discussed on: -arm, -mips
Tested by: zbb, brooks, imp, and others
MFC after: 6 weeks
new devmap.[ch] files. Emphasize the MD nature of these things by using
the prefix arm_devmap_ on the function and type names (already a few of
these things found their way into MI code, hopefully it will be harder to
do by accident in the future).
components instead of with the kernel and/or modules. This ensures that it
gets built with the host compiler, not the compiler in obj/... used to build
the target components (which may be a cross-compiler outputting code for a
different architecture and using header files with types and options set up
for the wrong architecture).
Reviewed by: imp
strings as uart_bus_fdt's probe().
The bus code uses ofw_bus_search_compatible() and that's not an option in
cpu (console) code -- it runs way before the ofw routines are usable. So
the console probe has its own loop to search the table, but now at least
there's only one table to be maintained when new devices are added.
The problems do not affect bouncing busdma in a visible way, but are
critical for the dmar backend.
- The bus_dmamap_create(9) is not documented to take BUS_DMA_NOWAIT flag.
- Unload descriptor map after receive.
- Do not reset descriptor map to NULL, bus_dmamap_load(9) requires
valid map, and also this leaks the map.
Reported and tested by: pho
Approved by: jfv
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
This includes the following:
- use separate memory regions for VALE ports
- locking fixes
- some simplifications in the NIC-specific routines
- performance improvements for the VALE switch
- some new features in the pkt-gen test program
- documentation updates
There are small API changes that require programs to be recompiled
(NETMAP_API has been bumped so you will detect old binaries at runtime).
In particular:
- struct netmap_slot now is 16 bytes to support an extra pointer,
which may save one data copy when using VALE ports or VMs;
- the struct netmap_if has two extra fields;
MFC after: 3 days
rather than just void *.
Then, as part of this, convert a couple of mbuf m->m_data accesses
to mtod(m, const void *).
Reviewed by: markm
Approved by: security-officer (delphij)
Sponsored by: Netflix, Inc.
CDC=0 simply means "no command codes", CDC=1 means "AT command codes."
There's no driver change required! It's purely to tell the application
layer whether to speak AT commands or not. Things are all still serial.
PR: usb/183505
Reviewed by: hps
MFC after: 1 week
is not idential to "uint32_t" when defining set channel prototype
functions. The WLAN channel range should be from 0 to 65535
inclusivly, and u_int should be fine for this purpose.
than one unit with four busses attached to it. This allows us to use
existing fdt data which describes separate devices with separate resources.
It also allows any combination of the units to be en/disabled in the
board dts files.
Adjust our dts code to match what's used by linux and u-boot now that
we're structured to do so.
Document lots of interesting stuff learned whiling doing this with a big
comment block in the driver, so I don't have to re-learn it for the next
round of changes.
mostly by adjustments to debugging printf() format specifiers. For high
numbered LUNs, also switch to printing them in hex as per SAM-5.
MFC after: 2 weeks
resist easy conversion since they implement a great deal of their attach
logic inside probe(). Some of this could be fixed by moving it to attach(),
but some requires something more subtle than BUS_PROBE_NOWILDCARD.
r235816 triggered kernel panic or hang after warm boot.
Don't blindly restore BCE_EMAC_MODE media configuration in
bce_reset(). If driver is about to shutdown it will invoke
bce_reset() which in turn results in restoring BCE_EMAC_MODE
media configuration. This operation seems to confuse controller
firmware.
Reported by: Paul Herman (herman <> cleverbridge dot com)
Tested by: sbruno, Paul Herman (herman <> cleverbridge dot com)
RTL8168GU has two variants(GMII and MII) but it uses the same chip
revision id. Driver checks PCI device id of controller and
sets internal capability flag(i.e. jumbo frame and link speed down
in WOL).
H/W donated by: RealTek Semiconductor Corp.
I don't have a copy of data sheet so I'm not sure exact PHY model
name. Vendor's web page indicates RTL8251 is latest PHY so I used
the name. This PHY is used with RTL8168G, RTL8168GU and RTL8411B.
the rate is 11n, rather than whether the channel is 11n.
This correctly allows the PLCP lookup code to return the legacy rates
even on an 11n channel.
PR: kern/183430
1.3 of Intelб╝ Virtualization Technology for Directed I/O Architecture
Specification. The Extended Context and PASIDs from the rev. 2.2 are
not supported, but I am not aware of any released hardware which
implements them. Code does not use queued invalidation, see comments
for the reason, and does not provide interrupt remapping services.
Code implements the management of the guest address space per domain
and allows to establish and tear down arbitrary mappings, but not
partial unmapping. The superpages are created as needed, but not
promoted. Faults are recorded, fault records could be obtained
programmatically, and printed on the console.
Implement the busdma(9) using DMARs. This busdma backend avoids
bouncing and provides security against misbehaving hardware and driver
bad programming, preventing leaks and corruption of the memory by wild
DMA accesses.
By default, the implementation is compiled into amd64 GENERIC kernel
but disabled; to enable, set hw.dmar.enable=1 loader tunable. Code is
written to work on i386, but testing there was low priority, and
driver is not enabled in GENERIC. Even with the DMAR turned on,
individual devices could be directed to use the bounce busdma with the
hw.busdma.pci<domain>:<bus>:<device>:<function>.bounce=1 tunable. If
DMARs are capable of the pass-through translations, it is used,
otherwise, an identity-mapping page table is constructed.
The driver was tested on Xeon 5400/5500 chipset legacy machine,
Haswell desktop and E5 SandyBridge dual-socket boxes, with ahci(4),
ata(4), bce(4), ehci(4), mfi(4), uhci(4), xhci(4) devices. It also
works with em(4) and igb(4), but there some fixes are needed for
drivers, which are not committed yet. Intel GPUs do not work with
DMAR (yet).
Many thanks to John Baldwin, who explained me the newbus integration;
Peter Holm, who did all testing and helped me to discover and
understand several incredible bugs; and to Jim Harris for the access
to the EDS and BWG and for listening when I have to explain my
findings to somebody.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
slightly unnerving.
In file included from ioctl.c:48:
/var/tmp/home/sbruno/bsd/head/tmp/usr/include/dev/lmc/if_lmc.h:939:13:
warning: no previous extern declaration for non-static variable 'ssi_cables'
[-Wmissing-variable-declarations]
const char *ssi_cables[] =
interface. Make MII drivers forget about 'struct ifnet'.
Later plan is to provide an administrative downcall from ifnet
layer into drivers, to inform them about administrative status
change. If someone thinks that processing MII events for an
administratively down interface is a big problem, then drivers
would turn MII processing off.
The following MII drivers do evil things, like strcmp() on
driver name, so they still need knowledge of ifnet and thus
include if_var.h. They all need to be fixed:
sys/dev/mii/brgphy.c
sys/dev/mii/e1000phy.c
sys/dev/mii/ip1000phy.c
sys/dev/mii/jmphy.c
sys/dev/mii/nsphy.c
sys/dev/mii/rgephy.c
sys/dev/mii/truephy.c
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
/chosen, following the list of allowed console properties in ePAPR. Also
do not require that stdin be defined and equal to stdout: stdin is
nonstandard (for ePAPR) and console in an unexpected place is after all
better than no console.
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
When using DW UART with BUSY detection it is necessary to wait
until all serial transfers are finished before manipulating the
line control. LCR will not be affected when UART is busy.
In addition, if Divisor Latch Access Bit is being set in order to
modify UART divisors:
1. We will get BUSY interrupt if interrupts are enabled.
2. Because LCR will not be affected the THR and (even worse) IER
contents will be corrupted. This will lead to console hang.
Approved by: cognet (mentor)
This is "STA invalid". I saw it during some 4965 testing (kern/183260)
and I still have no idea what is causing it.
Obtained from: Linux drivers/net/wireless/iwlegacy
Some firmware versions seem to get very unhappy if they're sent btcoex
commands when they don't actually have bluetooth hardware in them.
So, disable sending them those commands.
Tested:
* 5100 (which has bluetooth, no problems)
* 4965 (which doesn't have bluetooth, but didn't seem to crash)
* 6200 (no bluetooth, seems to get unhappy being sent bluetooth commands.)
index lookups.
* My recent(ish) change to iwn(4) and the net80211 rate control API to
support 11n rates broke the link quality table use. So, until I or
someone else decides to fix it, let's just disable it for now.
* Teach iwn_tx_data_raw() to use the iwn_rate_to_plcp() function.
* Eliminate two uses of the net80211 rate index lookup functions - they
are only for legacy rates and they're not needed here.
This fixes some invalid looking rate control TX issues that showed up
on my 4965 but it doesn't fix the two TX hangs I've noticed. Those look
like DMA related issues.
Tested:
* 4965, STA mode
* 5100, STA mode
associates compat strings with arbitrary values that mean something to
the driver. This is handy for drivers that support several variations
of similar hardware and need to know which one matched.
Reviewed by: imp, jmg, nwhitehorn
negative diff that should improve reliability somewhat. There should be
no differences in behavior -- please report any that crop up. This has been
tested on ARM and PPC systems.
Tested by: ray
referenced by pointer, making it non-static should not have even the
negligible impact on the existing code.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
BUS_PROBE_GENERIC and not BUS_PROBE_SPECIFIC (0) so the OFW SPI bus can
attach when enabled. Export the spibus devclass_t and driver_t
declarations.
Submitted by: ray
Approved by: adrian (mentor)
buffer. While here, make the code flow somewhat nicer.
Thanks to mav@ for tracking it down.
Tested by: mav
MFC after: 3 days
Sponsored by: FreeBSD Foundation
- ofw_bus_map_intr()
Maps an (iparent, IRQ) tuple to a system-global interrupt number in some
platform dependent way. This is meant to be implemented as a replacement
for [FDT_]MAP_IRQ() that is an MI interface that knows about the bus
hierarchy.
- ofw_bus_config_intr()
Configures an interrupt (previously mapped) based on firmware sense flags.
This replaces manual interpretation of the sense field in bus drivers and
will, in a follow-up, allow that interpretation to be redirected to the PIC
drivers where it belongs. This will eventually replace the tables in
/sys/dev/fdt/fdt_ARCH.c
The PowerPC/AIM code has been converted to use these globally, with an
implementation in terms of MAP_IRQ() and powerpc_config_intr(), assuming
OpenPIC, at the bus root in nexus(4). The ofw_bus_config_intr() will shortly
be integrated into pic_if.m and bounced through nexus into the PIC tree.
FDT integration will happen significantly later due to larger testing
requirements. This patch in general also lays the groundwork for the removal
of /sys/dev/fdt/fdt_ARCH.c and machine/fdt.h.
and OF_searchencprop(). I thought about using the element size parameter
to OF_getprop_alloc() to do endian-switching automatically, but it breaks
use with structs and a *lot* of FDT code (which can hopefully be moved to
these new APIs).
MFC after: 2 weeks
by encode-int. Specifically, it takes a set of 32-bit cell values and
changes them to host byte order. Most non-string instances of OF_getprop()
should be using this function, which is a no-op on big-endian platforms.
230523, 1123614
Implement a driver for Robert Norton's PIC as an FDT interrupt
controller. Devices whose interrupt-parent property points to a beripic
device will have their interrupt allocation, activation , and setup
operations routed through the IC rather than down the traditional bus
hierarchy.
This driver largely abstracts the underlying CPU away allowing the
PIC to be implemented on CPU's other than BERI. Due to insufficient
abstractions a small amount of MIPS specific code is currently required
in fdt_mips.c and to implement counters.
MFC after: 3 days
Sponsored by: DARPA/AFRL
- Use bus reference phandles in place of FDT offsets as IRQ domain keys
- Unify the identical macio/fdt/mambo OpenPIC drivers into one
- Be more forgiving (following ePAPR) about what we need from the device
tree to identify an OpenPIC
- Correctly map all IRQs into an interrupt domain
- Set IRQ_*_CONFORM for interrupts on an unknown PIC type instead of
failing attachment for that device.
When safety requirements are met, it allows to avoid passing I/O requests
to GEOM g_up/g_down thread, executing them directly in the caller context.
That allows to avoid CPU bottlenecks in g_up/g_down threads, plus avoid
several context switches per I/O.
The defined now safety requirements are:
- caller should not hold any locks and should be reenterable;
- callee should not depend on GEOM dual-threaded concurency semantics;
- on the way down, if request is unmapped while callee doesn't support it,
the context should be sleepable;
- kernel thread stack usage should be below 50%.
To keep compatibility with GEOM classes not meeting above requirements
new provider and consumer flags added:
- G_CF_DIRECT_SEND -- consumer code meets caller requirements (request);
- G_CF_DIRECT_RECEIVE -- consumer code meets callee requirements (done);
- G_PF_DIRECT_SEND -- provider code meets caller requirements (done);
- G_PF_DIRECT_RECEIVE -- provider code meets callee requirements (request).
Capable GEOM class can set them, allowing direct dispatch in cases where
it is safe. If any of requirements are not met, request is queued to
g_up or g_down thread same as before.
Such GEOM classes were reviewed and updated to support direct dispatch:
CONCAT, DEV, DISK, GATE, MD, MIRROR, MULTIPATH, NOP, PART, RAID, STRIPE,
VFS, ZERO, ZFS::VDEV, ZFS::ZVOL, all classes based on g_slice KPI (LABEL,
MAP, FLASHMAP, etc).
To declare direct completion capability disk(9) KPI got new flag equivalent
to G_PF_DIRECT_SEND -- DISKFLAG_DIRECT_COMPLETION. da(4) and ada(4) disk
drivers got it set now thanks to earlier CAM locking work.
This change more then twice increases peak block storage performance on
systems with manu CPUs, together with earlier CAM locking changes reaching
more then 1 million IOPS (512 byte raw reads from 16 SATA SSDs on 4 HBAs to
256 user-level threads).
Sponsored by: iXsystems, Inc.
MFC after: 2 months
This shuld have been a problem since r230587. Not exactly sure why it
was not detected the last weeks with the tinderbox. I would assume
r255744 is what started to cause it.
MFC after: 1 week
the cfi(4) driver. It remained in the tree longer than would be ideal
due to the time required to bring cfi(4) to feature parity.
Sponsored by: DARPA/AFRL
MFC after: 3 days
Implement support for interrupt-parent nodes in simplebus. The current
implementation requires that device declarations have an interrupt-parent
node and that it point to a device that has registered itself as a
interrupt controller in fdt_ic_list_head and implements the fdt_ic
interface.
Sponsored by: DARPA/AFRL
already. Also, according to the specs, GDRST register is not in the
power well, so the forcewake for reset status read is excessive for
this reason.
Use plain register read for waiting of the reset completion
notification, to avoid gt_lock recursion. Linux upstream did the
similar change, but their code was already restructured.
Reported by: ray
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
reduce lock congestion and improve SMP scalability of the SCSI/ATA stack,
preparing the ground for the coming next GEOM direct dispatch support.
Replace big per-SIM locks with bunch of smaller ones:
- per-LUN locks to protect device and peripheral drivers state;
- per-target locks to protect list of LUNs on target;
- per-bus locks to protect reference counting;
- per-send queue locks to protect queue of CCBs to be sent;
- per-done queue locks to protect queue of completed CCBs;
- remaining per-SIM locks now protect only HBA driver internals.
While holding LUN lock it is allowed (while not recommended for performance
reasons) to take SIM lock. The opposite acquisition order is forbidden.
All the other locks are leaf locks, that can be taken anywhere, but should
not be cascaded. Many functions, such as: xpt_action(), xpt_done(),
xpt_async(), xpt_create_path(), etc. are no longer require (but allow) SIM
lock to be held.
To keep compatibility and solve cases where SIM lock can't be dropped, all
xpt_async() calls in addition to xpt_done() calls are queued to completion
threads for async processing in clean environment without SIM lock held.
Instead of single CAM SWI thread, used for commands completion processing
before, use multiple (depending on number of CPUs) threads. Load balanced
between them using "hash" of the device B:T:L address.
HBA drivers that can drop SIM lock during completion processing and have
sufficient number of completion threads to efficiently scale to multiple
CPUs can use new function xpt_done_direct() to avoid extra context switch.
Make ahci(4) driver to use this mechanism depending on hardware setup.
Sponsored by: iXsystems, Inc.
MFC after: 2 months
Freescale SoCs including the i.MX series. This also works for the newer
SoCs with the ENET gigabit controller, but doesn't use any of the new
hardware features other than enabling gigabit speed.
BUS_PROBE_DEFAULT, it would attach to them all, producing both many
fdtbus instances and preventing other devices from attaching. Instead
return BUS_PROBE_NOWILDCARD, which exists for exactly this purpose.
Add an option ATSE_CFI_HACK to allow memory mapped CFI devices to have
their address range allocated sharable so that atse(4) can find it's
Ethernet address in the expected location.
We intend to remove this hack once the BERI platform has a loader.
221804, 221805, 222004, 222006, 222055, 222820, 1135077, 1135118, 1136259
Add atse(4), a driver for the Altera Triple Speed Ethernet MegaCore.
The current driver support gigabit Ethernet speeds only and works with
the MegaCore only in the internal FIFO configuration in the soon to be
open sourced BERI CPU configuration.
Submitted by: bz
MFC after: 3 days
Sponsored by: DARPA/AFRL
Change 231100 by brooks@brooks_zenith on 2013/07/12 21:01:31
Add a new option ALTERA_SDCARD_FAST_SIM which checks immediatly
for success of I/O operations rather than queuing a task.
MFC after: 3 days
Sponsored by: DARPA/AFRL
Change 227594 by brooks@brooks_zenith on 2013/04/11 17:10:14
When we fail, print the error that occured if we are giving
up or if bootverbose is set.
MFC after: 3 days
Sponsored by: DARPA/AFRL
- Remove two excessive and slow register reads from isp_intr(). Instead
of rereading value every time, assume that registers contain what we have
written there.
- Avoid sequential search through 4096 array elements when looking for
command tag. Use hash of lists to store active tags separately from free
ones and so greatly speedup the searches.
Reviewed by: mjacob
harvester, which now always calls hwrngs with the buffer length
multiple of the word size. This allows to remove the excessive memory
accesses to temporary buffer when saving the entropy word.
Streamline the assembly and unify it between i386 and amd64.
Reviewed by: markm, des
Approved by: so (des)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
* Do the hardware setup in the right order!
* Modify/improve the chip probe check so it can actually
probe the 7240/9340 directly (although it's not yet used..)
* Initialise and fetch the is_mii option
* Fix some debugging whilst I'm here.
This is enough to get things off the ground.
Tested:
* AR9344 SoC
* Add an AR9340 switch version entry;
* Support the switch being connected via MII;
* Add a flag to note that a switch is actually an internal
switch rather than an external switch.
Now:
* The ar9340 switch can interconnect via MII;
* Since some slightly different phy/switch register access methods
and quirks appear for the internal versus external switch,
we will need a flag to mark it as an "internal" switch.
Tested:
* AR9344 (internal switch)
* AR9331 (internal switch)
TODO:
* Test the AR8316 switch!
This is just the chip initialisation code (for now.)
It's not linked into the main build as it requires a bunch of other code
to be tidied up and committed. But it indeed does function as advertised.
Tested:
* AR9344 SoC
and not 8-bit. Fix support for isochronous transfers in USB host mode.
Fix a whitespace while at it.
MFC after: 1 week
Reported by: SAITOU Toshihide <toshi@ruby.ocn.ne.jp>
PR: usb/181987
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs, grehan
Approved by: re (gjb)
sys/sys/systm.h:
* Add a new VM_GUEST type, VM_GUEST_HV (HyperV guest).
sys/dev/hyperv/vmbus/hv_vmbus_drv_freebsd.c:
sys/dev/hyperv/vmbus/hv_hv.c:
sys/dev/hyperv/stordisengage/hv_ata_pci_disengage.c:
* Set vm_guest to VM_GUEST_HV and use that on other HyperV related
devices instead of cloning the cpuid hypervisor check.
* Cleanup the vmbus_identify function.
prior releases.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (gjb)
sys/dev/xen/blkfront/blkfront.c:
On XenServer versions up to an including 6.2, paravirtualized
CDROM support is broken. When running in an HVM domain,
ignore paravirtualized instances of CDROM media, and instead
rely on native drivers attaching to emulated hardware. This
functions correctly on all currently known Xen based
platforms.
to dummy,yarrow and break the usability of /dev/random.
Fix the name of the tunable to something logical that 'sysctl kern.random'
emits.
Submitted by: des@ (the idea, code by me)
Refactor of /dev/random device. Main points include:
* Userland seeding is no longer used. This auto-seeds at boot time
on PC/Desktop setups; this may need some tweeking and intelligence
from those folks setting up embedded boxes, but the work is believed
to be minimal.
* An entropy cache is written to /entropy (even during installation)
and the kernel uses this at next boot.
* An entropy file written to /boot/entropy can be loaded by loader(8)
* Hardware sources such as rdrand are fed into Yarrow, and are no
longer available raw.
------------------------------------------------------------------------
r256240 | des | 2013-10-09 21:14:16 +0100 (Wed, 09 Oct 2013) | 4 lines
Add a RANDOM_RWFILE option and hide the entropy cache code behind it.
Rename YARROW_RNG and FORTUNA_RNG to RANDOM_YARROW and RANDOM_FORTUNA.
Add the RANDOM_* options to LINT.
------------------------------------------------------------------------
r256239 | des | 2013-10-09 21:12:59 +0100 (Wed, 09 Oct 2013) | 2 lines
Define RANDOM_PURE_RNDTEST for rndtest(4).
------------------------------------------------------------------------
r256204 | des | 2013-10-09 18:51:38 +0100 (Wed, 09 Oct 2013) | 2 lines
staticize struct random_hardware_source
------------------------------------------------------------------------
r256203 | markm | 2013-10-09 18:50:36 +0100 (Wed, 09 Oct 2013) | 2 lines
Wrap some policy-rich code in 'if NOTYET' until we can thresh out
what it really needs to do.
------------------------------------------------------------------------
r256184 | des | 2013-10-09 10:13:12 +0100 (Wed, 09 Oct 2013) | 2 lines
Re-add /dev/urandom for compatibility purposes.
------------------------------------------------------------------------
r256182 | des | 2013-10-09 10:11:14 +0100 (Wed, 09 Oct 2013) | 3 lines
Add missing include guards and move the existing ones out of the
implementation namespace.
------------------------------------------------------------------------
r256168 | markm | 2013-10-08 23:14:07 +0100 (Tue, 08 Oct 2013) | 10 lines
Fix some just-noticed problems:
o Allow this to work with "nodevice random" by fixing where the
MALLOC pool is defined.
o Fix the explicit reseed code. This was correct as submitted, but
in the project branch doesn't need to set the "seeded" bit as this
is done correctly in the "unblock" function.
o Remove some debug ifdeffing.
o Adjust comments.
------------------------------------------------------------------------
r256159 | markm | 2013-10-08 19:48:11 +0100 (Tue, 08 Oct 2013) | 6 lines
Time to eat crow for me.
I replaced the sx_* locks that Arthur used with regular mutexes;
this turned out the be the wrong thing to do as the locks need to
be sleepable. Revert this folly.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com> (In original diff)
------------------------------------------------------------------------
r256138 | des | 2013-10-08 12:05:26 +0100 (Tue, 08 Oct 2013) | 10 lines
Add YARROW_RNG and FORTUNA_RNG to sys/conf/options.
Add a SYSINIT that forces a reseed during proc0 setup, which happens
fairly late in the boot process.
Add a RANDOM_DEBUG option which enables some debugging printf()s.
Add a new RANDOM_ATTACH entropy source which harvests entropy from the
get_cyclecount() delta across each call to a device attach method.
------------------------------------------------------------------------
r256135 | markm | 2013-10-08 07:54:52 +0100 (Tue, 08 Oct 2013) | 8 lines
Debugging. My attempt at EVENTHANDLER(multiuser) was a failure; use
EVENTHANDLER(mountroot) instead.
This means we can't count on /var being present, so something will
need to be done about harvesting /var/db/entropy/... .
Some policy now needs to be sorted out, and a pre-sync cache needs
to be written, but apart from that we are now ready to go.
Over to review.
------------------------------------------------------------------------
r256094 | markm | 2013-10-06 23:45:02 +0100 (Sun, 06 Oct 2013) | 8 lines
Snapshot.
Looking pretty good; this mostly works now. New code includes:
* Read cached entropy at startup, both from files and from loader(8)
preloaded entropy. Failures are soft, but announced. Untested.
* Use EVENTHANDLER to do above just before we go multiuser. Untested.
------------------------------------------------------------------------
r256088 | markm | 2013-10-06 14:01:42 +0100 (Sun, 06 Oct 2013) | 2 lines
Fix up the man page for random(4). This mainly removes no-longer-relevant
details about HW RNGs, reseeding explicitly and user-supplied
entropy.
------------------------------------------------------------------------
r256087 | markm | 2013-10-06 13:43:42 +0100 (Sun, 06 Oct 2013) | 6 lines
As userland writing to /dev/random is no more, remove the "better
than nothing" bootstrap mode.
Add SWI harvesting to the mix.
My box seeds Yarrow by itself in a few seconds! YMMV; more to follow.
------------------------------------------------------------------------
r256086 | markm | 2013-10-06 13:40:32 +0100 (Sun, 06 Oct 2013) | 11 lines
Debug run. This now works, except that the "live" sources haven't
been tested. With all sources turned on, this unlocks itself in
a couple of seconds! That is no my box, and there is no guarantee
that this will be the case everywhere.
* Cut debug prints.
* Use the same locks/mutexes all the way through.
* Be a tad more conservative about entropy estimates.
------------------------------------------------------------------------
r256084 | markm | 2013-10-06 13:35:29 +0100 (Sun, 06 Oct 2013) | 5 lines
Don't use the "real" assembler mnemonics; older compilers may not
understand them (like when building CURRENT on 9.x).
# Submitted by: Konstantin Belousov <kostikbel@gmail.com>
------------------------------------------------------------------------
r256081 | markm | 2013-10-06 10:55:28 +0100 (Sun, 06 Oct 2013) | 12 lines
SNAPSHOT.
Simplify the malloc pools; We only need one for this device.
Simplify the harvest queue.
Marginally improve the entropy pool hashing, making it a bit faster
in the process.
Connect up the hardware "live" source harvesting. This is simplistic
for now, and will need to be made rate-adaptive.
All of the above passes a compile test but needs to be debugged.
------------------------------------------------------------------------
r256042 | markm | 2013-10-04 07:55:06 +0100 (Fri, 04 Oct 2013) | 25 lines
Snapshot. This passes the build test, but has not yet been finished or debugged.
Contains:
* Refactor the hardware RNG CPU instruction sources to feed into
the software mixer. This is unfinished. The actual harvesting needs
to be sorted out. Modified by me (see below).
* Remove 'frac' parameter from random_harvest(). This was never
used and adds extra code for no good reason.
* Remove device write entropy harvesting. This provided a weak
attack vector, was not very good at bootstrapping the device. To
follow will be a replacement explicit reseed knob.
* Separate out all the RANDOM_PURE sources into separate harvest
entities. This adds some secuity in the case where more than one
is present.
* Review all the code and fix anything obviously messy or inconsistent.
Address som review concerns while I'm here, like rename the pseudo-rng
to 'dummy'.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com> (the first item)
------------------------------------------------------------------------
r255319 | markm | 2013-09-06 18:51:52 +0100 (Fri, 06 Sep 2013) | 4 lines
Yarrow wants entropy estimations to be conservative; the usual idea
is that if you are certain you have N bits of entropy, you declare
N/2.
------------------------------------------------------------------------
r255075 | markm | 2013-08-30 18:47:53 +0100 (Fri, 30 Aug 2013) | 4 lines
Remove short-lived idea; thread to harvest (eg) RDRAND enropy into the
usual harvest queues. It was a nifty idea, but too heavyweight.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com>
------------------------------------------------------------------------
r255071 | markm | 2013-08-30 12:42:57 +0100 (Fri, 30 Aug 2013) | 4 lines
Separate out the Software RNG entropy harvesting queue and thread
into its own files.
# Submitted by: Arthur Mesh <arthurmesh@gmail.com>
------------------------------------------------------------------------
r254934 | markm | 2013-08-26 20:07:03 +0100 (Mon, 26 Aug 2013) | 2 lines
Remove the short-lived namei experiment.
------------------------------------------------------------------------
r254928 | markm | 2013-08-26 19:35:21 +0100 (Mon, 26 Aug 2013) | 2 lines
Snapshot; Do some running repairs on entropy harvesting. More needs
to follow.
------------------------------------------------------------------------
r254927 | markm | 2013-08-26 19:29:51 +0100 (Mon, 26 Aug 2013) | 15 lines
Snapshot of current work;
1) Clean up namespace; only use "Yarrow" where it is Yarrow-specific
or close enough to the Yarrow algorithm. For the rest use a neutral
name.
2) Tidy up headers; put private stuff in private places. More could
be done here.
3) Streamline the hashing/encryption; no need for a 256-bit counter;
128 bits will last for long enough.
There are bits of debug code lying around; these will be removed
at a later stage.
------------------------------------------------------------------------
r254784 | markm | 2013-08-24 14:54:56 +0100 (Sat, 24 Aug 2013) | 39 lines
1) example (partially humorous random_adaptor, that I call "EXAMPLE")
* It's not meant to be used in a real system, it's there to show how
the basics of how to create interfaces for random_adaptors. Perhaps
it should belong in a manual page
2) Move probe.c's functionality in to random_adaptors.c
* rename random_ident_hardware() to random_adaptor_choose()
3) Introduce a new way to choose (or select) random_adaptors via tunable
"rngs_want" It's a list of comma separated names of adaptors, ordered
by preferences. I.e.:
rngs_want="yarrow,rdrand"
Such setting would cause yarrow to be preferred to rdrand. If neither of
them are available (or registered), then system will default to
something reasonable (currently yarrow). If yarrow is not present, then
we fall back to the adaptor that's first on the list of registered
adaptors.
4) Introduce a way where RNGs can play a role of entropy source. This is
mostly useful for HW rngs.
The way I envision this is that every HW RNG will use this
functionality by default. Functionality to disable this is also present.
I have an example of how to use this in random_adaptor_example.c (see
modload event, and init function)
5) fix kern.random.adaptors from
kern.random.adaptors: yarrowpanicblock
to
kern.random.adaptors: yarrow,panic,block
6) add kern.random.active_adaptor to indicate currently selected
adaptor:
root@freebsd04:~ # sysctl kern.random.active_adaptor
kern.random.active_adaptor: yarrow
# Submitted by: Arthur Mesh <arthurmesh@gmail.com>
Submitted by: Dag-Erling Smørgrav <des@FreeBSD.org>, Arthur Mesh <arthurmesh@gmail.com>
Reviewed by: des@FreeBSD.org
Approved by: re (delphij)
Approved by: secteam (des,delphij)
and holding a reference prior to calling further into the hyperv
stack.
Added missing FreeBSD idents.
Submitted by: Microsoft hyperv dev team
Approved by: re@ (gjb)
Fixed a panic that occurs when bringing up an interface on 57710/57711
running very old bootcode versions.
Fixed how bool is defined for those who have been using this code on older
versions of FreeBSD.
Approved by: re@ (gjb)
Approved by: davidch (mentor)
union members in strict C99, by giving them names. While here, add some
FreeBSD keywords where they were missing.
Approved by: re (gjb)
Reviewed by: grehan
and there are ifnets, that do that via counter(9). Provide a flag that
would skip cache line trashing '+=' operation in ether_input().
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Reviewed by: melifaro, adrian
Approved by: re (marius)
- This version has support for the new Intel Avoton systems,
including 2.5Gb support, further it now has IPv6/TSO6 support as
well. Shared code has been updated where necessary as well. Thanks
to my new assistant Eric Joyner for doing the transmit path changes
to bring in the IPv6/TSO6 support. Thanks to Gleb for catching the
one bug and change needed in NETMAP.
Approved by: re
o Allow this to work with "nodevice random" by fixing where the MALLOC pool is defined.
o Fix the explicit reseed code. This was correct as submitted, but in the project branch doesn't need to set the "seeded" bit as this is done correctly in the "unblock" function.
o Remove some debug ifdeffing.
o Adjust comments.
I replaced the sx_* locks that Arthur used with regular mutexes; this turned out the be the wrong thing to do as the locks need to be sleepable. Revert this folly.
Submitted by: Arthur Mesh <arthurmesh@gmail.com> (In original diff)
extensions, we can change the .byte directives in sys/dev/random/ivy.c
to plain 'rdrand' mnemonics. This already worked for clang users, but
now it will also work for gcc users.
Approved by: re (kib)
Approved by: so (des)
MFC after: 1 week
they occur.
This prevents repeated notifications of the same event.
Status of these events may be viewed at any time by viewing the
SMART/Health Info Page using nvmecontrol, whether or not asynchronous
events notifications for those events are enabled. This log page can
be viewed using:
nvmecontrol logpage -p 2 <ctrlr id>
Future enhancements may re-enable these notifications on a periodic basis
so that if the notified condition persists, it will continue to be logged.
Sponsored by: Intel
Reviewed by: carl
Approved by: re (hrs)
MFC after: 1 week
when calculating stats in nvmecontrol perftest.
Sponsored by: Intel
Reported by: Joe Golio <joseph.golio@emc.com>
Reviewed by: carl
Approved by: re (hrs)
MFC after: 1 week
The AR5212 series of MACs implement the same channel counters as the
later 11n chips - except, of course, the 11n specific counter (extension
channel busy.)
This allows users of these NICs to use 'athsurvey' to see how busy their
current channel is.
Tested:
* AR5212, AR2413 NICs, STA mode
Approved by: re@ (gleb)
Add a SYSINIT that forces a reseed during proc0 setup, which happens
fairly late in the boot process.
Add a RANDOM_DEBUG option which enables some debugging printf()s.
Add a new RANDOM_ATTACH entropy source which harvests entropy from the
get_cyclecount() delta across each call to a device attach method.
This means we can't count on /var being present, so something will need to be done about harvesting /var/db/entropy/... .
Some policy now needs to be sorted out, and a pre-sync cache needs to be written, but apart from that we are now ready to go.
Over to review.
Looking pretty good; this mostly works now. New code includes:
* Read cached entropy at startup, both from files and from loader(8) preloaded entropy. Failures are soft, but announced. Untested.
* Use EVENTHANDLER to do above just before we go multiuser. Untested.
been tested. With all sources turned on, this unlocks itself in
a couple of seconds! That is no my box, and there is no guarantee
that this will be the case everywhere.
* Cut debug prints.
* Use the same locks/mutexes all the way through.
* Be a tad more conservative about entropy estimates.
Simplify the malloc pools; We only need one for this device.
Simplify the harvest queue.
Marginally improve the entropy pool hashing, making it a bit faster in the process.
Connect up the hardware "live" source harvesting. This is simplistic for now, and will need to be made rate-adaptive.
All of the above passes a compile test but needs to be debugged.
field. Perform vcpu enumeration for Xen PV and HVM environments
and convert all Xen drivers to use vcpu_id instead of a hard coded
assumption of the mapping algorithm (acpi or apic ID) in use.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (blanket Xen)
amd64/include/pcpu.h:
i386/include/pcpu.h:
Add vcpu_id to the amd64 and i386 pcpu structures.
dev/xen/timer/timer.c
x86/xen/xen_intr.c
Use new vcpu_id instead of assuming acpi_id == vcpu_id.
i386/xen/mp_machdep.c:
i386/xen/mptable.c
x86/xen/hvm.c:
Perform Xen HVM and Xen full PV vcpu_id mapping.
x86/xen/hvm.c:
x86/acpica/madt.c
Change SYSINIT ordering of acpi CPU enumeration so that it
is guaranteed to be available at the time of Xen HVM vcpu
id mapping.
aware drivers on Xen hypervisors that advertise support for some
HyperV features.
x86/xen/hvm.c:
When running in HVM mode on a Xen hypervisor, set vm_guest
to VM_GUEST_XEN so other virtualization aware components in
the FreeBSD kernel can detect this mode is active.
dev/hyperv/vmbus/hv_hv.c:
Use vm_guest to ignore Xen's HyperV emulation when Xen is
detected and Xen PV drivers are active.
Reported by: Shanker Balan
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (Xen blanket)
Device level sysctls are already exposed as dev.ix.<device>
Fixing the case where number of queues for igb is auto-tuned and
hw.igb.num_queues does not return current/updated value.
Reviewed by: jfv
Approved by: re (delphij)
MFC after: 2 weeks
Contains:
* Refactor the hardware RNG CPU instruction sources to feed into
the software mixer. This is unfinished. The actual harvesting needs
to be sorted out. Modified by me (see below).
* Remove 'frac' parameter from random_harvest(). This was never
used and adds extra code for no good reason.
* Remove device write entropy harvesting. This provided a weak
attack vector, was not very good at bootstrapping the device. To
follow will be a replacement explicit reseed knob.
* Separate out all the RANDOM_PURE sources into separate harvest
entities. This adds some secuity in the case where more than one
is present.
* Review all the code and fix anything obviously messy or inconsistent.
Address som review concerns while I'm here, like rename the pseudo-rng
to 'dummy'.
Submitted by: Arthur Mesh <arthurmesh@gmail.com> (the first item)
Update the OFED Infiniband core to the version supplied in Linux
version 3.7.
The update to OFED is nearly all additional defines and functions
with the exception of the addition of additional parameters to
ib_register_device() and the reg_user_mr callback.
In addition the ibcore (Infiniband core) and ipoib (IP over Infiniband)
have both been made into completely loadable modules to facilitate
testing of the OFED stack in FreeBSD.
Finally the Mellanox Infiniband drivers are now updated to the
latest version shipping with Linux 3.7.
Submitted by: Mellanox FreeBSD driver team:
Oded Shanoon (odeds mellanox.com),
Meny Yossefi (menyy mellanox.com),
Orit Moskovich (oritm mellanox.com)
Approved by: re
original, this hides the contents of cam_compat.h from ktrace/kdump/truss,
avoiding problems there. There are no user-servicable parts in there, so
no need for those tools to be groping around in there.
Approved by: re
- Remove the timeout_ch field. It's been deprecated since FreeBSD 7.0;
MPSAFE drivers should be managing their own timeout storage. The
remaining non-MPSAFE drivers have been modified to also manage their own
storage, and should be considered for updating to MPSAFE (or removal)
during the FreeBSD 10.x lifecycle.
- Add fields related to soft timeouts and quality of service, to be used
in upcoming work.
- Add room for more flags in the CCB header and path_inq structures.
- Begin support for extended 64-bit LUNs.
- Bump the CAM version number to 0x18, but add compat shims. Tested with
camcontrol and smartctl.
Reviewed by: nathanw, ken, kib
Approved by: re
Obtained from: Netflix
structure in the driver.
Having these in 10.0 means that mfiutil can be modified to take adavantage
of new updates without a kernel recompile.
Approved by: re (gjb)
MFC after: 2 weeks
routing if we get certain errors. Poll for command completion upon
command timeouts. The XHCI error events might not generate interrupts.
MFC after: 1 week
Reported by: Daniel Gerzo <danger@rulez.sk>, Antonis Anastasiadis <anastasiadis@datalive.gr>
PR: usb/181159
Approved by: re (gjb)
current lock classes KPI it was really difficult because there was no
way to pass an rmtracker object to the lock/unlock routines. In order
to accomplish the task, modify the aforementioned functions so that
they can return (or pass as argument) an uinptr_t, which is in the rm
case used to hold a pointer to struct rm_priotracker for current
thread. As an added bonus, this fixes rm_sleep() in the rm shared
case, which right now can communicate priotracker structure between
lc_unlock()/lc_lock().
Suggested by: jhb
Reviewed by: jhb
Approved by: re (delphij)
Xen PVHVM guest.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (blanket Xen)
MFC after: 2 weeks
sys/amd64/amd64/mp_machdep.c:
sys/i386/i386/mp_machdep.c:
- Make sure that are no MMU related IPIs pending on migration.
- Reset pending IPI_BITMAP on resume.
- Init vcpu_info on resume.
sys/amd64/include/intr_machdep.h:
sys/i386/include/intr_machdep.h:
sys/x86/acpica/acpi_wakeup.c:
sys/x86/x86/intr_machdep.c:
sys/x86/isa/atpic.c:
sys/x86/x86/io_apic.c:
sys/x86/x86/local_apic.c:
- Add a "suspend_cancelled" parameter to pic_resume(). For the
Xen PIC, restoration of interrupt services differs between
the aborted suspend and normal resume cases, so we must provide
this information.
sys/dev/acpica/acpi_timer.c:
sys/dev/xen/timer/timer.c:
sys/timetc.h:
- Don't swap out "suspend safe" timers across a suspend/resume
cycle. This includes the Xen PV and ACPI timers.
sys/dev/xen/control/control.c:
- Perform proper suspend/resume process for PVHVM:
- Suspend all APs before going into suspension, this allows us
to reset the vcpu_info on resume for each AP.
- Reset shared info page and callback on resume.
sys/dev/xen/timer/timer.c:
- Implement suspend/resume support for the PV timer. Since FreeBSD
doesn't perform a per-cpu resume of the timer, we need to call
smp_rendezvous in order to correctly resume the timer on each CPU.
sys/dev/xen/xenpci/xenpci.c:
- Don't reset the PCI interrupt on each suspend/resume.
sys/kern/subr_smp.c:
- When suspending a PVHVM domain make sure there are no MMU IPIs
in-flight, or we will get a lockup on resume due to the fact that
pending event channels are not carried over on migration.
- Implement a generic version of restart_cpus that can be used by
suspended and stopped cpus.
sys/x86/xen/hvm.c:
- Implement resume support for the hypercall page and shared info.
- Clear vcpu_info so it can be reset by APs when resuming from
suspension.
sys/dev/xen/xenpci/xenpci.c:
sys/x86/xen/hvm.c:
sys/x86/xen/xen_intr.c:
- Support UP kernel configurations.
sys/x86/xen/xen_intr.c:
- Properly rebind per-cpus VIRQs and IPIs on resume.
