as separate 16-bit entities. Some of the ring control blocks are
in NIC memory, so they must be referenced using 32-bit accesses.
Smaller accesses have been observed to fail under some conditions.
This caused the rings to be set up wrong, leading to writes by the
card outside of the intended bounds of the rings. This problem was
diagnosed by Michael Barthelow. Don Bowman submitted a patch which
fixed the problem using a slightly different approach.
Reference ring control blocks in NIC memory using a pointer to
volatile.
Parenthesize the BGE_HOSTADDR macro definition properly.
MFC after: 3 days
from the hardware descriptors to avoid the overhead of having a DMA
map for each of them. Bump the number of hardware descriptors to 128,
and use half as many software descriptors for now.
Some minor cleanups.
- remove DPRINTF(), there is a CTR*() for any of them, and KTR is
far more useful to debug this driver.
- some cleanups; remove some unused code and definitions.
o create a separate tag for each object allocated with bus_dmamem_alloc so
the tag's maxsize is setup appropriately; this reduces memory allocation
for the queue descriptors from 16M to what it should be and also fixes
memory allocation for public key operands
o release bus dma resources on detach so module usage doesn't leak
o remove public key op disable now that bus dma memory allocation is fixed
o collect attach error handling in one place
Sponsored by: Vernier Networks
- 'spec' and 'ver' are attributes of a unit rather than a node.
- Report Phy and Link info separatelly.
- Reorder intialization step in fwohci_reset().
- Fix some bogosity with mixing unit numbers and channels, which would only
work for one instance of the device.
- Use a simpler scheme for input and output queueing.
- Use db_alt_break.
- Separate fc->dev (i.e. fwohci0) and fc->bdev (i.e. firewire0).
- Remove unused firewirebusreg.h.
- Reduce size of descriptor block for asynchronous transmit and
check the number of descriptor when copying from mbuf.
- Skip mbuf whose length is zero. NFS seems passing such mbuf and
some chips generates unrecoverable error.
- Restore pci config registers after resume.
- Reinitialize and start rx buffers after resume.
- Don't reallocate memory in fwohci_db_init() if the dbch is
already initialized.
- Fix typo.
- Some clean up.
positions for the status bits of port a and port b are different. To
avoid needing to know which channel the interrupt handler is working on,
shift the status bits for port a into the port b bit positions, and always
check the port b status bits. This fixes using port b, which I neglected
to test before.
- Remember to update the channel's tty structure from the passed in termios
in the param routine.
- Minor style.
Metricom Ricochet GS modem. Add them here.
# A new umodem appears to be needed to make the sanyo phone work, but that's
# more extensive and will come after coordination.
With a 1 byte transmit fifo, 3 byte receive fifo, and wierd multiplexed I/O
designed for a Z80 cpu, this chip redefines suckage.
Based on the openbsd and netbsd drivers. Only really works as a console,
modem support is not complete since I can't test it.
this was causing filedesc work to be very painful.
In order to make this work split out sigio definitions to thier own header
(sigio.h) which is included from proc.h for the time being.
for the raidctl device.
Select a more conservative default for the permissions for /dev/raidctl
since the operations are performed using ioctl() not read() and write().
Submitted by: kris
Reviewed by: scottl
Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and
(NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is
more strict about checking these values that other arches.
were sometimes propagated using M_COPY_PKTHDR which actually did
something between a "move" and a "copy" operation. This is replaced
by M_MOVE_PKTHDR (which copies the pkthdr contents and "removes" it
from the source mbuf) and m_dup_pkthdr which copies the packet
header contents including any m_tag chain. This corrects numerous
problems whereby mbuf tags could be lost during packet manipulations.
These changes also introduce arguments to m_tag_copy and m_tag_copy_chain
to specify if the tag copy work should potentially block. This
introduces an incompatibility with openbsd which we may want to revisit.
Note that move/dup of packet headers does not handle target mbufs
that have a cluster bound to them. We may want to support this;
for now we watch for it with an assert.
Finally, M_COPYFLAGS was updated to include M_FIRSTFRAG|M_LASTFRAG.
Supported by: Vernier Networks
Reviewed by: Robert Watson <rwatson@FreeBSD.org>
work. The interface was gleaned from the Linux driver. Currently only
one RX & one TX buffer are used. Firmware support is not tested so for the
MPI-350 so it is disabled. Signal cache and monitor mode are not supported
yet. Signal cache is not supported since in encapsulation mode ethernet
frames are returned by the chip. LAN monitor mode support will be added
shortly. Thanks to Warner for the MPI-350 card he sent me.
Add support for RSSI map from PR kern/32880 which was incomplete. Enhanced
with the ability to select the cache mode of raw, dbm or per-cent.
Clean up Signal/Noise/Quality structures and units with help from
Marco Molteni.
Change flash to use a malloc'ed buffer when needed.
PR: kern/32880
Submitted by: Douglas S. J. De Couto decouto@pdos.lcs.mit.edu,
Marco Molteni
MFC: 3 weeks
than hard-coded uids and gids.
Switch the device to a group of wheel instead of operator.
Narrow down the permissions on the device to require root privilege
to manipulate the system power state. It may be that we can broaden
access to the device after review of the access control in ACPI.
Submitted by: kris
Reviewed by: takawata
with make_dev(). Use OPERATOR instead of implicit WHEEL to match
other storage devices. Use a mode of 0640 to be consistent
with other storage devices.
Submitted by: kris
Reviewed by: scottl
Remove the setgid bit from the tga device (?).
Synchronize mode with modes used for related frame buffer devices
in MAKEDEV (tga doesn't appear in MAKEDEV).
Submitted by: kris
improves protection consistency with other storage devices (generally
root:operator,660). This driver appears not to have an active
maintainer.
Submitted by: kris
command in case this setting was not saved. Since bandwidth reclamation
(-current only) often results in bus activity continuing to the end
of every frame, most transfers would fail with IOERROR if this
setting is missed.
Reviewed by: n_hibma
MFC after: 1 week
- Fix permission of device node.
fwochi.c, fwohcireg.h
- Detect phy access failure correct way.
- Set root hold-off bit before initiating bus reset.
This should fix the problem with VIA6306.
fwohcivar.h
- Fix over-allocation of array. (fwohcivar.h)
sbp.c
- Return CAM_DEV_NOT_THERE rather than CAM_TID_INVALID to prevent retry.
- Added support for ITR (interrupt throttle register). This feature is available on
adapters based on 82545 and above
- Fixed problem with vlan support when traffic has priority bits set. (kern/45907)
PR: kern/45907
MFC after: 1 week
I/O port range, then we should ignore a resource if it's NOT
a memory range AND NOT an I/O port range.
The OR in the condition caused us to ignore perfectly valid
memory addresses.
While here, remove redundant parenthesis and reindent the
debug print to avoid long lines.
identify themselves as serial cards that it would be desirable to
attach a different driver than sio to. Since we are claiming all
serial cards, this is not possible. Instead, return -100 to indicate
that we're willing to take the card, but still allow other drivers to
attach.
Pointed out by: Maksim Yevmenkin
not < the size of the device. This avoids geom complaints.
Fix a serious bug in the handling of the RS_NO_CLEAR_UA quirk. When we
go and insert the test-unit-ready command the umass_cam_quirk_cb() function
sets the status as if the READ_CAPACITY command suceeded when, in fact, it
did not. This leads to the CAM layer trying to use garbage in the return
buffer and panicing the system (or doing other bad things).
Add a quirk entry for MSYSTEMS DISK-ON-KEY, which is sold under the Sony
brand as a solid state disk-on-key usb device. This device requires
several quirks to work properly.
Note that the disk-on-key device will not work properly until CAM also
gets a quirk entry for it, which has been submitted to the CAM maintainer,
and you may have to temporarily uncomment the DELAY() as well. -current
does not properly wait for devices to power up so you may also have
to temporarily uncomment the DELAY(300000) to make your device work.
A solution must be found to that issue.
MFC after: 3 days
X-MFC note: the quirk support must MFCd before this patch can be
the dataphysend calculation could only possibly work if the virtual buffer
is also physically contiguous. Calculate dataphysend by calculating the
ending virtual address first, then converting to a physical address.
The second bug applies only to NetBSD and OpenBSD and involves the curlen
calculation in the two-contiguous-physical-pages case (which we don't support).
Also cleanup the use of the OHIC_PAGE() macro on dataphysend and add a panic
if len goes negative (meaning we lost the physical page translation
representing the end of the buffer).
IMHO the dataphysend is still bokered since it might be misrepresented
by shared userland page mappings. The whole section needs to be rewritten
to use the virtual address range.
MFC after: 3 days
prototype for trm_detach and freeing all resources.
While I'm there, handle better errors in trm_attach and remove the
PCI_BASE_ADDR0 definition, since it's what PCIR_MAPS is used for.
MFC after: 3 days
kernel memory allocator, is harmless. This could be a problem for
other systems, though. I've modified Darren's patch a little.
Original patch by: Darren Schack, Isilon Systems, Inc <darrens@isilon.com>
Also analysed by: SGI, and in particular Divy Le Ray of SGI
OK'ed by: re(rwatson)
as module. This also fix's issue kern/45713.
Fix - polling was implemented incorrectly for
adapter enquiry and adapter flush.
(2) Problem: PANIC when unloading driver
as module.
Fix - device nodes are not destroyed for amr0,
and amrd* when driver is unloaded
(3) Problem: PANIC from loading driver when
3ware adapter present, error message "Warning
"amrd is usurping twed's bmaj"
Fix - put #idef freebsd version < 500000 for
bmaj -1 -> amrd_cdevsw
(4) Problem: warnings in driver when compiling
with DAMR_DEBUG param enabled in Makefile
Fix - fix the warnings so driver can compile
when -Werror is present in Makefile.
Approved by: jhb
MFC: 7 days
labels are acurate in relation to a fully compiled
sequencer program (all patches downloaded). Correct
a few occurances of a relative jump across a macro
that ended up jumping us into the last instruction
of the macro.
Spproved by: re (bmah)
ahd_pci.c:
Retrieve the allow_memio hint from the resource manager to
determine whether or not to try PCI MEMIO.
aic79xx_osm.h:
aic7xxx_osm.h:
Don't wrongly abuse the callout_reset() interface when trying
to abuse timeouts generated from the CAM layer. This fixes the
console freeze and lost timeout problem that many have reported,
especially on SMP systems.
aic79xx_pci.c
aic7xxx_pci.c
Rewrite the MEMIO test routine to prevent certain broken chipsets
from trying to burst multiple DWORDs to the registers. Also make
the routine better detect byte merging by the host bridge and
deal with it.
aic79xx.reg:
Correct an incorrect register definition.
Approved by: re (rwatson, jhb)
This mostly consists of functionality to serialize accesses to
the two ATA channels (which can also be used to "fix" certain
PCI based controllers).
Add support for Acard controllers.
Enable the ATA driver in PC98 GENERIC, and add device hints.
Update man page with latest support.
The PC98 core team has kindly provided me with a PC98
machine that made this all possible, thanks to all that
contributed to that effort, without that this would
probably newer have been possible..
Approved by: re@
We allow the request to go through if it matches either a prefetchable
or a non-prefetchable part of the bridge. We do not check to make
sure it is the right kind of memory because most drivers to not yet
properly set RF_PREFETCHABLE (only cardbus seems to do so, and I'm not
entirely sure it does it right). RF_PREFETCHABLE was invented for
cardbus, so hasn't been properly documented yet.
This is still overridable by hw.pci.allow_unsupported_io_ranges, but
the need for that is greatly reduced, especially for the nvida driver.
Approved by: re
Reviewed by: jhb and many testers
Submitted by: Matt Emmerton (although this has been reworked somewhat)
could already exist, and this triggers a booby trap panic in make_dev.
remove_plex_entry: Don't remove the stripe mutex here, it gets done in
free_plex.
Approved by: re (rwatson)
the device is not actually present), clear the corresponding bit in
the ch->devices bitmap. This resolves a panic that occurred with ATAPI/CAM
after an APM suspend/resume, when the ATA hardware would erroneously
report an extra ATAPI device.
Approved by: re, sos
Reviewed by: roberto
MFC after: 7 days
version, plus add support for the new features found in the Rev B
version of the chip. The changelog is quite long and can be provided
on request. Major features include vastly improved protocol violation
handling, full support for the 7902 Rev B, better parity error
handling, and better packetized overrun handling, to name a few.
Approved by: re (blanket)
HP -> CPQ
Rearrange IDs to better match which chips they use.
Convert to uniform product description strings.
Simplify 7901A setup function.
Add the NONPACKFIFO_BUG and PACED_NEGTABLE_BUG entries
for the A.
Add rev B bugs and features.
The double write workaround for CURRSCB is only required if
abort pending is set. Remove this work around and set the
abort pending bug bit on the B at least until we have better
confirmation that the double write is always safe.
Add updated H2B identifiers
Move IOCell paramters into softc and add a hook for the
OSM to modify these as well as other settings prior to
committing them to the chip.
SLEW -> SLEWRATE
PREQDIS in DEVCONFIG1 went away after the A2.
Remove all code that references this bit. This
is especially important since this bit was reused
in the B for a different HW fix workaround.
Properly set the AHD_NEW_IOCELL_OPTS and
AHD_NEW_DFCNTRL_OPTS features for the B.
Remove stray/random extra 7901A generic PCI
table entry. Also switch the correct 7901A
generic entry to use ID_ALL_MASK since we
can only differentiate the 7901A from the
7902 by checking for a "type field" of 0xE.
Set AHD_INTCOLLISIONT_BUG for the Rev B.
Set the PREQDIS bit in DEVCONFIG1 for the B. The
bit is misnamed, but seems to disable a work-around
that breaks on the B on PCI busses.
Add a routine for testing memory mapped register access.
This will hopefully detect things like buggy via chipsets
so that the OSM can fallback to using I/O mapped access
when memory mapped I/O simply will not work.
Approved by: re (blanket)
diagnostic "Setting Mode" messages.
Use a read of HCNTRL to flush our write to CLRCMDCMPLT
on the RevB. This allows us to check to see if the sequencer
is paused and to initiate the interrupt collision workaround
without incuring an extra read.
Approved by: re (blanket)
PCI-X only workarounds are automatically masked out
if we are operating in PCI mode.
Make use of ahd_pci_test_register_access()
Approved by: re (blanket)
Move IOCell paramters into softc and add a hook for the
OSM to modify these as well as other settings prior to
committing them to the chip.
Approved by: re (blanket)
in the per-device kthread. This ensures that synchronisation with
mddestroy() succeeds even if the kthread was not waiting in tsleep()
at the time of the wakeup(). Among other things, this fixes the
problem of mdconfig getting stuck when an attempt is made to use a
zero-length file as a vnode-type backing store.
Approved by: re
aic7xxx.c:
aic7xxx.h:
aic7xxx.reg:
aic7xxx.seq:
Bring in the protocol violation handler from the U320
driver and replace the NO_IDENT sequencer interrupt code
with the PROTO_VIOLATION code. Support for this code
required the following changes:
SEQ_FLAGS:
IDENTIFY_SEEN -> NOT_IDENTIFIED
Added NO_CDB_SENT
SCB_CONTROL:
TARGET_SCB == STATUS_RCVD for initiator mode
scb->flags:
Added SCB_TARGET_SCB since we cannot rely on
TARGET_SCB as a target/initiator differentiator
due to it being overloaded in initiator mode to
indicate that status has been received.
aic7xxx.seq:
Move data fifo CLRCHN to mesgin_rdptrs which is a safer
location for doing this operation. This also saves a
sequencer instruction.
aic7xxx.c:
aic7xxx.h:
Change ahc/ahd_upate_neg_request() to take a "negotiation
type" enum that allows us to negotiate:
o only if the goal and current parameters differ.
o only if the goal is non-async
o always - even if the negotiation will be for async.
aic7xxx.seq:
Reset the FIFO whenever a short CDB transfer occurs
so that the FIFO contents do not corrupt a future CDB
transfer retry.
Add support for catching the various protocol violations
handled by ahc_handle_protocol_violation.
Reformat some comments.
aic7xxx.c:
aic7xxx.h:
Just for safety, have the aic7xxx driver probe
the stack depth.
aic7xxx.c:
aic7xxx.h:
Save and restore stack contents during diagnostics.
Some chip variants overwrite stale entries on a
stack "pop".
Don't use 0 to probe the stack depth. 0 is the typical
value used to backfill the stack if entries are overwritten
on a "pop".
aic7xxx.h:
Add a missing typedef.
Collapse SCB flag entries so they are bit contiguous.
Add AHD_ULTRA2_XFER_PERIOD for narrow fallback calculations
aic7xxx.c:
Don't panic (as a diagnostic to catch bugs) if we decided to
force the renegotiation of async even if we believe we are
already async. This should allow us to negotiate async instead
of the full user goal rate during startup if bus resets are
disabled.
Add a space to the end of the ahc/ahd_print_devinfo routines
so that it behaves as expected by the code that uses it.
Only force a renegotiation on a selection timeout
if the SCB was valid. Doing otherwise may be dangerous
as the connection was not valid for an unknown reason.
Add additional diagnostic output to ahc_dump_card_state(),
and have it use the register pretty printing functions.
Update ahc_reg_print() to handle a NULL cur_col.
Add a newline to ahc_dump_card_state() output.
Bring back "use_ppr". We need to use_ppr anytime
doppr is true or we have non-zero protocol options.
The later case was not handled in the recent removal
of use_ppr.
Move a comment and remove a useless clearing of use_ppr.
Don't disable ENBUSFREE when single stepping on
a DT capable controller. We cannot re-enable unexpected
busfree detection, so we must clear BUSFREE on each
step instead.
Correct the lookup of the SCB ID in ahc_handle_proto_error.
Remove a diagnostic printf.
Remove unecessary restoration of the STACK for older
chips.
Approved by: re (blanket)
This will hopefully detect things like buggy via chipsets
so that the OSM can fallback to using I/O mapped access
when memory mapped I/O simply will not work.
Approved by: re (blanket)
AHC_ALLOW_MEMIO is set, or the hint hint.ahc.N.allow_memio=1 is
set in the bootloader.
Make use of ah?_pci_test_register_access().
Approved by: re (blanket)
o Add needed headers.
o Add stg_products[] product data and stg_match() function.
o Change stg_pccard_method[] to support both OLDCARD and NEWCARD.
Approved by: re
o Add needed headers.
o Add ncv_products[] product data and ncv_match() function.
o Change ncv_pccard_method[] to support both OLDCARD and NEWCARD.
Suggestion for REX-5572 matching part by imp.
Approved by: re
o Add needed headers.
o Add nsp_producs[] product data and nsp_match() function.
o Change nsp_pccard_method[] to support both OLDCARD and NEWCARD.
o Add warning to fall back to PIO mode when it cannot use SMIT mode.
This is needed because memories are not allocated with NEWCARD now.
Submitted by: takawata
Approved by: re
or stg driver. They are,
Macnica mPS110, PANASONIC(KME) KXLC004, Qlogic Fast SCSI,
Workbit Ultra Ninja-16, (ID based)
Future Domain SCSI2GO, IBM SCSI PCMCIA card, I-O DATA CBSC16,
Macnica mPS100, Newmedia BASICS-SCSI, RATOC REX-5536, RATOC REX-5536AM,
RATOC REX-5536M, RATOC REX5572, Workbit NinjaSCSI-3
(CIS based)
Note: We need vendor IDs WORKBIT2 and IODATA3 which is -1, since some
cards does not have IDs in the CIS and fails to be probed without
this fake vendor IDs.
o Change the strings of RATOC REX_R280 from REX-R280 to REX-R280/REX-9530.
This reminds us that REX-R280 and REX-R9530 have same ID (same product).
Reviewed by: imp
Approved by: re
Obtained from: /etc/defaults/pccard.conf,
List of CIS tupples by Toshihiko ARAI and PAO project:
http://www.linkclub.or.jp/~clover/cis/
Change suggestion by: HASEGAWA Tomoki <thasegawa@mta.biglobe.ne.jp>
for I-O DATA CBSC16 entry
There were no serious problem reports on this in spite of my concern.
To get debug output from acpi_pci_link, just enable bootverbose flag
in usual manner (boot -v).
Approved by: re
aicasm_gram.y:
Use a direct move from allzeros to emulate a
mvi of 0.
aicasm_insformat.h:
sync $Id$
aicasm_symbol.c:
Minor header change.
Approved by: re (blanket)
pci_get_ether accesor, which gets it from the CIS for cardbus cards
(and from other pci-like buses via whatever mechanism is used there).
Submitted by: sam
Approved by: re (blanket)
sometimes, so return it when requested and it does. Also a little
more infrastructure for a few other things.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
buses support querying the MAC address in a standard-for-that-bus way.
The base pci bus returns NULL for this IVAR always.
Submitted by: sam
Approved by: re (blanket for NEWCARD)
- If a PCI device is not present, then a 32-bit read_config() is going to
return 0xffffffff not 0xffff.
- For the 82454NX chipset, the MIOC that we read the bus numbers of the
various host-PCI bridges from is at function (slot) 0x10 not 0x0.
Approved by: re (rwatson)
1. Detect the revision of the Rhine chip we're using.
2. Use the force reset command on revisions which support
it whenever the normal reset command fails.
This should solve a wide range of "my vr0 locks up with reset
failed messages" problems. (Although the root causes should
be eventually tracked down.)
Tested by: grenville armitage <garmitage@swin.edu.au>
Obtained from: Via's if_fet driver
MFC after: 3 days
Approved by: re
If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
to PCI bridge can be read be evaluating the _BBN method of the host to PCI
device. Unfortunately, there appear to be some lazy/ignorant/moronic/
whatever BIOS writers that return 0 for _BBN for all host to PCI bridges in
the system. On a system with a single host to PCI bridge this is not a
problem as the child bus of that single bridge will be bus 0 anyway.
However, on systems with multiple host to PCI bridges and l/i/m/w BIOS
writers this is a major problem resulting in all but the first host to
PCI bridge failing to attach. So, this adds a workaround.
If the _BBN of a host to PCI bridge is zero and pcib0 already exists
and is not us, the we use _ADR to look up our PCI function and slot
(we currently assume we are on bus 0) and use that to call
host_pcib_get_busno() to try and extract our bus number from config
registers on the host to PCI bridge device. If that fails, then we make
an evil assumption that ACPI's _SB_ namespace lays out the host to PCI
bridges in ascending order and use our pcib unit number as our bus
number.
Approved by: re
after configure() has run. Only create the device if ofwcons is the
highest priority console. Make a dev alias with the same name as the
firmware output-device property.
trigger a breakpoint with this chip.
- Fiddle the right bits in the cn input and output routines to disable port
interrupts and enable visibility of the masked interrupt status bits.
- Register a shutdown final event handler to put the chip back in the mode
that the prom expects.
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
o Use 32-bit unsigned types for things that really are 32-bit quantities,
not bus_addr_t. These are not the same as a bus_addr_t, so don't use
that here. Harmless on i386, introduced problems on sparc64.
Submitted by: jhb
bit in the PCI command register for the device. Otherwise, device drivers
that look at this register to see which types of BARs are usable will think
that none of them are.
This allows my Adaptec 1480A cardbus card to finally work.
Reviewed by: imp
alpha. This will take the file out of sync with the private version
that we maintain, but alpha tinderbox has been broken for too long.
Tested on: i386, sparc64, alpha
- Fix some especially bad style in the CIS BAR tuple parsing code.
- activate Option ROMS correctly.
- de-obfuscate the Option ROM image selection code.
- Fix mis-interpretation of the PCI spec that prevented Option ROMs whose
CIS section wasn't in the first image from working.
- Fix mis-interpretation of the PCI spec that prevented CIS's mapped into
MEMIO space from working at all.
- Reject invalid CIS pointers.
Reviewed by: imp
- Set RDTR to zero by default instead of 28.
- Fixed a problem with TX hangs with jumbo frames when number of fragments in the mbuf chain
is large.
- Added support for 82540EP based cards.
MFC after: 3 days
is not long long on all archs. (They happen to be long's on 64-bit arch's
and gcc considers that significant enough to warn about it.) These should
probably be uintmax_t but I didn't feel like adding all the extra includes.
these were cosmetic. However, at least two of these changes fix bugs
where a (fake) pointer to a RX descriptor was added to the physical
memory start address with the cast in the wrong place resulting in
rxdesc[pmem_start] instead of (uintptr_t)rxdesc + pmem_start.
just limited to the DEVICE_POLLING case. This removes the FXP_RFA_RNRMARK
hack, and replaces it with a softc flag that is used to record when
the handling of a no-resource condition was deferred due to running
out of DEVICE_POLLING cycles. This was tested on -stable, but the
code is essentially the same as in -current. It should only affect
the case where DEVICE_POLLING is defined.
The details of the mechanism behind the crashes are still uncertain
but the most likely cause seems to be some kind of hardware confusion
when the no-resource recovery code is accidentally invoked while
the receiver is still active. This could have happened if the
hardware left the 0x4000 bit of the RFA status word set. The comments
in the commit log for revision 1.142 stating that the driver could
clash with the hardware writing to this status word were not correct.
Tested by: Guy Helmer <ghelmer@palisadesys.com>
from being MI in any fashion. It currently "assumes" that it can get
a kernel virtual address for a phyiscal address by adding KERNBASE to the
physical address. It also tries to read values out of a the PC BIOS on
all archs. It also uses "manual" inb() and outb()'s to talk to the mcclock
device which just happens to be at that location on both i386 and alpha.
This driver should likely be i386-only.
acpi_cmbat_init_battery() and acpi_cmbat_init_acline() respectively.
Call acpi_cmbat_init_battery() from acpi_cmbat_resume() too just in
case.
This is a workaround for embedded controller operations which is
unstable for about a minute (typically 30 or 40 sec.) at boot time.
o Always release the resources on device detach.
o Attach resources the same with driver added as we do we do in the insert
case (maybe this should be a routine).
o signal the wakeup of the thread on resume instead of trying to force an
interrupt.
o Minor debug hacks.
o use 0xffffffff instead of -1 for uint32_t items.
o Don't complain when we're asked to detach no cards. This is normal.
o Eliminate the now worthless second parameter to card_detach_card.
o minor style(9)isms
Some of these patches may be from: iwasaki-san, jhb, iadowse
state. Instead, use ACPI_STA_PRESENT and ACPI_STA_FUNCTIONAL for it.
In some ACPI BIOS implementations, boot disabled devices don't have
ACPI_STA_ENABLE bit in _STA object.
Also it is not fatal if getting current IRQ of boot disabled devices
is failed in initial state.
And minor fixes.
amr_cam.c,
amrreg.h,
amrvar.h:
- added support for 12/16 byte cdb's, effecting CAM branch only ( non-disk support )
amrreg.h:
- increased number of scatter gather elements from 16 to 26.
amr_pci.c:
- amr_pci_free(), incorrect bus tag meant for 'amr_mailbox_dmat' was being freed
all:
- copyright change requested by scottl
Reviewed by: ps,scottl
MFC after: 1 week
across system suspends on the Intel 82371AB PCI-ISA bridge. On a
Sony Vaio C1XD that I have, these registers are not set correctly
after an ACPI resume. The result is that after resuming, a shared
IRQ is left in edge-triggered mode so the interrupt can later become
jammed in a state where the line remains asserted, but the handler
is never called.
Reviewed by: jhb
behaviour of the hardware: a possibly reserved bit of the receive
descriptor (RFA) `status' field is borrowed to record no-resource
(RNR) events, and the same status field is read and written to at
a time that may clash with the hardware updating this field.
There is no hardware documentation available to determine if these
things are safe to do; the second issue almost certainly isn't, and
the first is only safe if there is documentation saying that this
bit is free to be used by the driver. The PR referenced below
provides extremely convincing evidence that the changes cause random
crashes on some (unusual) hardware.
Since these features are only required by the DEVICE_POLLING case,
this commit makes their use conditional on that option. It does not
change the DEVICE_POLLING case, but at least people with the rare
hardware on which this code causes problems can now avoid the crashes
by not enabling DEVICE_POLLING.
PR: kern/42260
Reviewed by: luigi
Problem revision found by: Pawel Malachowski <pawmal@unia.3lo.lublin.pl>
Tested by: Pawel Malachowski <pawmal@unia.3lo.lublin.pl>
MFC after: 1 week
pipe callback function, and just return if these cases are detected.
Without these checks, the ulpt driver may cause an infinite loop
of failing USB transfers that can hang the whole machine. This makes
printing work for me on a HP DJ950C printer.
- Add detach support to the driver so that you can kldunload the module.
Note that currently rc_detach() fails to detach a unit if any of its
child devices are open, thus a kldunload will fail if any of the tty
devices are currently open.
- sys/i386/isa/ic/cd180.h was moved to sys/dev/ic/cd180.h as part of
this change.
Requested by: rwatson
Tested by: rwatson
and XPT_RESET_DEV.
In order to properly handle reset requests whether they originate in the
ATA layer (atacontrol reinit) or from the CAM layer (camcontrol reset)
ata_reinit does not cause the SIM to be deallocated anymore. The SIM
is now unconditionnally created for each ATAPI bus.
This change may cause existing bus ids to change on some setups.
Reviewed by: roberto
Approved by: sos
creation by GCC-2.6.3. Casting pointers to unsigned char
to volatile pointers to unsigned char seemed to produce
better results on the ia32 architecture with old versions
of GCC.
The current FreeBSD system compiler GCC-3.2.1 emits
better sign extension code for non-volatile variables:
volatile char c;
int i = c;
is compiled to:
...
movb -1(%ebp), %al
movbsl %al, %eax
movl %eax, -8(%ebp)
...
char c;
int i = c;
is compiled to:
...
movbsl -1(%ebp), %eax
movl %eax, -8(%ebp)
...
The same holds for zero-extension of dereferenced pointers
to volatile unsigned char.
When compiled on alpha or sparc64, the code produced for the
two examples above does not differ.
* Change atapi-cd ioctls to use the same units.
* Change burncd, cdcontrol to convert CDROM speed to KB/sec before
calling the ioctl. Add a "max" speed option for their command lines.
This change does not break ABI but does change the units passed through
the ioctl so 3rd party software that uses cdrio.h will have to convert
(most likely by multiplying CDROM speed by 177 to get KB/s).
PR: kern/36845
Submitted by: Philipp Mergenthaler <p@i609a.hadiko.de> (CAM ioctls)
Reviewed by: sos, ken
MFC after: 1 month
changes for "LSILogic"
(2) enabled non-disk support through CAM interface
(3) HA_INQ (a) enabled tagged queuing (b) disable reset during
driver loading (b) renamed BSDi string to LSI
(4) disabled detecting disk devices during SCSI INQUIRY
(5) changed dcdb single element sglist to send one entire buffer chunk
(6) nsgelem not set in sglist
(7) ap_data_transfer_length not set for dcdb
(8) changed "struct thread" to "d_thread_t" for compatibliity { xxx_open,
xxx_close, xxx_ioctl }
(9) miscellaneous compatiblity fixes
(10) bug fix for 0x0409/0x1000 card
(11) added compiling amr_cam.c in sys/conf/files
(12) added compiling amr_cam.c in sys/modules/amr/Makefile
Reviewed by:ps
MFC after:1 week
1 week
In that case use proc0's pid to return the thread ID.
- For 4-stable, use the generic swi taskqueue for ACPI events rather than
implementing our own.
Sponsored by: The Weather Channel
o instead of a list of mbufs use a list of m_tag structures a la openbsd
o for netgraph et. al. extend the stock openbsd m_tag to include a 32-bit
ABI/module number cookie
o for openbsd compatibility define a well-known cookie MTAG_ABI_COMPAT and
use this in defining openbsd-compatible m_tag_find and m_tag_get routines
o rewrite KAME use of aux mbufs in terms of packet tags
o eliminate the most heavily used aux mbufs by adding an additional struct
inpcb parameter to ip_output and ip6_output to allow the IPsec code to
locate the security policy to apply to outbound packets
o bump __FreeBSD_version so code can be conditionalized
o fixup ipfilter's call to ip_output based on __FreeBSD_version
Reviewed by: julian, luigi (silent), -arch, -net, darren
Approved by: julian, silence from everyone else
Obtained from: openbsd (mostly)
MFC after: 1 month
of KBDIO_DEBUG which may be defined in the kernel config (as it is in NOTES).
This kind of bug is a _really_ horribly thing as we end up with one bit
of code thinking a particular structure is 136 bytes and another that it
is only 112 bytes.
Ideally all places would remember to #include the right "opt_foo.h" file,
but I think in practice file containing the variable sized struct should
#include it explicitly as a precaution.
Detected by: FlexeLint
pci_cvt_to_bwx.
This doesn't necessarily make bge(4) now actually *work* on an alpha.
It loads, configures, and then about 30 seconds later, my XP1000 hard
freezes. But, hey, it's a start.
Obtained from: gallatin@freebsd.org
clear the bit. This allows ata driver to attach its children because
it needs the interrupts enabled to succeed.
Submitted by: iwasaki-san
o Spell CardBus as CardBus, not Cardbus or CardBUS while I'm here.
The problem is that the code does a check for the granparent of
the Promise chip, if this is a bridge of the right type, we have
a TX4 on our hands, and need to handle that ones "issues".
Now the grandparent check cause subtle bugs in the newbus system,
mainly that pci_get_devid doesn't return an error value.
This patch works around the issue by using BUS_READ_IVAR() instead.
o Implement the thread killing interlock as described by jhb in arch@
while talking to markm.
o Hold Giant around cbb_insert()/cbb_remove(). Deep in the belly of
the vm code we panic if we don't hold this when we activate the memory
for reading the CIS.
o If we had to do the kludge alloc, then do a kludge free.
o Better resume code. Move the comments around. Force the socket state to
be querried. Ack the interrupts properly.
o Intercept the interrupt requests and keep a list of interrupts to service
ourselves. When the card attaches, set its OK bit. When we get a card
status change interrupt for that card, clear the OK bit. Don't call the
ISR if the OK bit is cleared. Iwasaki-san and yamamoto-san have both
sent me patches that fix the same problem this fixes, but at the pccard
level.
o Try to get the signalling of the thread to actually die. This might not be
100% right, but it is less wrong than before.
o Add a SIC next to a TI type that looks like it could be wrong, but isn't.
the card.
o Add comments about how we're doing the CIS activation.
o Add location and pnp info functions.
o Add better code to hopefully deal with ata cards better (and other drivers
that allocate resources that we didn't preallocate from the CIS). OLDCARD
used to allow it, but NEWCARD was pickier. I'm not 100% sure this works,
but it doesn't break anything.
give us slightly better error checking than before and interpret what
default bits mean better. See the NetBSD CVS tree for the authors of
these changes (revs 1.10 .. 1.17).
Note, we return the PCI pnp info, but in fact that's wrong to do
since that data is not defined for CardBus cards. CardBus says that
these registers are undefined and one should use the CIS to do
device matching. To date, all CardBus cards have had these
registered defined, no doubt because they are using common silicon
to produce both the PCI cards and the CardBus cards. However, it isn't
any worse than the rest of the system, so just note it in passing and
move on.
o Also sort prototypes while I'm here.
currently disabled):
o Don't use constants for the output parameter, use the iparam count as a
pointer to the first result location.
o Fix bits vs bytes counting problems.
o Split out the hardware and software normalization versions of modexp.
o Enable hardware normalization for chips that support it.
o On reset, disable hardware normalization for 582x and make sure the
chip is in little endian mode.
o Since sw normalization is now the only option, simplify normalization
handling.
Also fix RNG harvesting: disabling PK support (for the moment) had disabled
the MCR2 interrupt; consider both KEY support and RNG support when deciding
whether or not to enable it.
Obtained from: openbsd
OpenBSD who got the code (or the idea) from the NetBSD tlp driver.
This gets some cardbus dc cards working (either completely or nearly
so). It also appears to get additional pci cards working, without
breaking working ones.
# Maybe some additional work is needed here. Also, the cardbus attachment
# might need to match on the CIS rather than on the vendor/device so we have
# a finer level of detail as to what the card is. Technically, the
# vendor/device fields are undefined for CardBus (even though most cards are
# using common silicon with pci models).
NB: But it will enable it in all kernels not having options "NO_GEOM"
Put the GEOM related options into the intended order.
Add "options NO_GEOM" to all kernel configs apart from NOTES.
In some order of controlled fashion, the NO_GEOM options will be
removed, architecture by architecture in the coming days.
There are currently three known issues which may force people to
need the NO_GEOM option:
boot0cfg/fdisk:
Tries to update the MBR while it is being used to control
slices. GEOM does not allow this as a direct operation.
SCSI floppy drives:
Appearantly the scsi-da driver return "EBUSY" if no media
is inserted. This is wrong, it should return ENXIO.
PC98:
It is unclear if GEOM correctly recognizes all variants of
PC98 disklabels. (Help Wanted! I have neither docs nor HW)
These issues are all being worked.
Sponsored by: DARPA & NAI Labs.
(1) Use namei() and devfs to discover devices rather than a hard-coded
MAKEDEV implementation. Once rootfs is in place, this will allow
Vinum to be used for the root file system partition.
(2) Pass FREAD to device opens so that GEOM will return sector size
rather than an error on attempts to read label data.
(3) Avoid clobbering return values from close_drive() and masking this
failure, resulting in a later divide by zero due to not having
updated the Vinum-cached sector size.
(4) Ignore failures from DIOCWLABEL as that appears not to be required
in the GEOM environment.
We've done testing in simple Vinum environments, but those with more
complex environments might want to give this a spin in DP2 and make
sure everything is up to speed.
Fixes in collaboration with: iedowse
Reviewed by: grog
before freeing so that WITNESS doesn't dereference mutex data pointers
and page fault. It's now possible to unload vinum.ko with a GENERIC
kernel on 5.0-CURRENT without panic.
Debugged/fixed with the aid of: jake, grog
This allocate the best IRQ to boot-disable devices (have IRQ 0).
Allocated IRQ will be used for PCI interrupt routing when ACPI is
enabled.
Note that verbose messaging enabled for the time being so that
people can easily notice the strange behavior if it happened.
dereference the struct sigio pointer without any locking. Change
fgetown() to take a reference to the pointer instead of a copy of the
pointer and call SIGIO_LOCK() before copying the pointer and
dereferencing it.
Reviewed by: rwatson
doesn't give them enough stack to do much before blowing away the pcb.
This adds MI and MD code to allow the allocation of an alternate kstack
who's size can be speficied when calling kthread_create. Passing the
value 0 prevents the alternate kstack from being created. Note that the
ia64 MD code is missing for now, and PowerPC was only partially written
due to the pmap.c being incomplete there.
Though this patch does not modify anything to make use of the alternate
kstack, acpi and usb are good candidates.
Reviewed by: jake, peter, jhb
supported option and it disabled a whole 2 lines of bootverbose messages.
I wanted to see 1 of the messages (about the latency timers). This
is a wrong place to decode pci configurations, but the code is already
here and handles more details than pciconf(8).
A number of functions in this driver still use the unit number in their
printouts because they pass the unit directly as a function argument
instead of passing a softc or struct ifnet pointer. This should be
resolved at a future date.
code path to fix a bug in the non USB_USE_SOFTINTR path that caused
the usb bus to hang and generally misbehave when devices were unplugged.
In the process though it also reduced the throughput of usb devices because
of a less than optimal implementation under FreeBSD.
This commit fixes the non USB_USE_SOFTINTR code in uhci and ohci
so that it works again, and switches back to using this code path.
The uhci code has been tested, but the ohci code hasn't. It's
essentially the same anyway and so I don't envisage any difficulties.
Code for uhci submitted by: Maksim Yevmenkin <myevmenk@exodus.net>
testing any modifications to them, they shouldn't even bother with
disklabels in the first place and they are just plain obsolete old
hardware which should be axed entirely before 5.0-R IMO.
Sponsored by: DARPA & NAI Labs.
The advanced stage of computer assisted hardware design and
verification is aptly illustrated by the fact that this is necessary
because only the first ports in a single-chip, dual-port async
PC-Card product lacks this register.
aic79xx.c:
o Remove redundant ahd_update_modes() call.
o Correct panic in diagnostic should state corruption cause
the SCB Id to be invalid during a selection timeout.
o Add workaround for missing BUSFREEREV feature in Rev A silicon.
o Corect formatting nits.
o Use register pretty printing in more places.
o Save and restore our SCB pointer when updating the waiting queue
list for an "expected" LQ-out busfree.
o In ahd_clear_intstat, deal with the missing autoclear in the
CLRLQO* registers.
o BE fixup in a diagnostic printf.
o Make sure that we are in the proper mode before disabling
selections in ahd_update_pending_scbs.
o Add more diagnostics.
o task_attribute_nonpkt_tag -> task_attribute: we don't need a
nonpkt_tag field anymore for allowing all 512 SCBs to be
used in non-packetized connections.
o Negotiate HOLD_MCS to U320 devices.
o Add a few additional mode assertions.
o Restore the chip mode after clearing out the qinfifo so that
code using ahd_abort_scbs sees a consistent mode.
o Simplify the DMA engine shutdown routine prior to performing
a bus reset.
o Perform the sequencer restart after a chip reset prior to
setting up our timer to poll for the reset to be complete.
On some OSes, the timer could actually pre-empt us and order
is important here.
o Have our "reset poller" set the expected mode since there is
no guarantee of what mode will be in force when we are called
from the OS timer.
o Save and restore the SCB pointer in ahd_dump_card_state(). This
routine must not modify card state.
o Ditto for ahd_dump_scbs().
aic79xx.h:
o Add a few more chip bug definitions.
o Align our tag on a 32bit boundary.
aic79xx.reg:
aic79xx.seq:
o Start work on removing workarounds for Rev B.
o Use a special location in scratch from for stroring
our SCBPTR during legacy FIFO allocations. This corrects
problems in mixed packetized/non-packetized configurations
where calling into a FIFO task corrupted our SCBPTR.
o Don't rely on DMA priority to guarantee that all data in
our FIFOs will flush prior to a command completion notification
going out of the command channel. We've never seen this assumption
fail, but better safe than sorry.
o Deal with missing BUSFREEREV feature in H2A.
o Simplify disconnect list code now that the list will always
have only a single entry.
o Implement the AHD_REG_SLOW_SETTLE_BUG workaround.
o Swith to using "REG_ISR" for local mode scratch during
our ISR.
o Add a missing jmp to the data_group_dma_loop after our
data pointers have been re-initialized by the kernel.
o Correct test in the bitbucket code so that we actually
wait for the bitbucket to complete before signaling the
kernel of the overrun condition.
o Reposition pkt_saveptrs to avoid a jmp instruction.
o Update a comment to reflect that the code now waits for
a FIFO to drain prior to issuing a CLRCHN.
aic79xx_inline.h:
o Remove unused untagged queue handling code.
o Don't attempt to htole64 what could be a 32bit value.
aic79xx_pci.c:
o Set additional bug flags for rev A chips.
aac driver dependent on the linux emulation module. This was
especially bad for the release engineers who tried to move the
aac driver from the kernel onto the drivers floppy. The linux
compat bits for this driver are now in their own driver, aac_linux.
It can be loaded as a module or compiled into the kernel. For
the latter case, the AAC_COMPAT_LINUX option is needed, along with
the COMPAT_LINUX option.
I've tested this in every configuration I can think of. This is an
MFC candidate for 4.7.
Idea from: rwatson
MFC after: 3 days
Linux driver defines 0x103[B-E] so add those as well.
Obtained from: Intel Linux e100 driver
MFC: Immediately if re@ allows it, otherwise after 4.7-RELEASE
of 1024- Ultra4 256). Rename 'requests' tag to 'request_pool' for clarity.
Make sure we do correct xpt_freeze_simq/CAM_RELEASE_SIMQ if we run out
of chip resources.
MFC after: 6 days
In mpttimeout, call mpt_intr just on the offchance that we missed
an interrupt. We can check to see whether or not the command that
is timing out got completed.
When we *do* decide to timeout a command, set the command state to
REQ_TIMEOUT and then invoke another timeout (hz/10)- mpttimeout2.
This allows us to catch a couple cases we've seen where the command
we timed out on in fact is ready to be completed by the firmware.
In any case, it's only after mpttimeout2 is called that we actually
take down the private state and free the request itself. CAM has
been notified in mpttimeout anyway. This whole area should be redone,
but that will take 105% of my available game time for this month.
Fix a couple of missing (and not useful, at presnet) CAMLOCK_2_MPTLOCK
and MPTLOCK_2_CAMLOCK locations.
Split mpt_notify into mpt_ctlop, which handles all reply completions
that have 0x800000000 or'd into the ContextID. This function can, in
fact, call mpt_event_notify_reply, which handles the traditional
async event notifications. While we're at it, put in the extremely
important (but currently untested) code that send back an Ack to
an Event Notification (if the Event Notification is marked with
AckRequired). Note that an Ack also generates another ctlop completion,
tra la.
Fix up mpt_done substantially to try and get how we plug into CAM
correctly done. Remove bogus CAM_RELEASE_SIMQ settings.
Do some cleanups in mpt_action that are related to speed negotiation
for Ultra4 cards. This is an area that is still quite fragile and
worrisome as config data being read back often doesn't make sense or
jibe with the documentation.
At any rate, after these changes were done, I was finally able to
get Lars Eggert's dual 320M disk system to stay up under load all
weekend- hopefully we're in good enough for now shape.
MFC after: 1 week
Define the CFG_DAGA_OFF offset as 128 bytes instead of 40- gives us
a more reasonable headroom.
When reading a config page, zero out the entire request area- not just
the length of the request. This is because we cleverly (cheezily) return
configuration data back into the allocated request area, so it's nice
to make sure we start with a clean area to write on.
MFC after: 1 week
Instead, based upon whether ISP_DAC_SUPPORTED is defined, typedef
isp_dma_addr_t appropriately.
If ISP_DAC_SUPPORTRED is defined, the DMA_WD2/DMA_WD3 macros do something
useful, else they define to '0'.
defined, we set the address space limitation to BUS_SPACE_UNRESTRICTED,
otherwise to BUS_SPACE_MAXADDR_32BIT.
If we have a 1240, ULTRA2 or better, or an FC card, the boundary limit
is BUS_SPACE_UNRESTRICTED and segment limit is BUS_SPACE_MAXADDR_32BIT.
The older 1020/1040 cards have boundary and segment limits of
BUS_SPACE_MAXADDR_24BIT.
disabling memory write invalidate unconditionally. It looks like
they've decided that MWI just doesn't work with these devices.
Also, remove now-irrelevant code that set PCI write boundary values
based on the cache line size.
MFC after: 2 weeks
and predictable way, and I apologize if I have gotten it wrong anywhere,
getting prior review on a patch like this is not feasible, considering
the number of people involved and hardware availability etc.)
If struct disklabel is the messenger: kill the messenger.
Inside struct disk we had a struct disklabel which disk drivers used to
communicate certain metrics to the disklayer above (GEOM or the disk
mini-layer). This commit changes this communication to use four
explicit fields instead.
Amongst the benefits is that the fields do not get overwritten by
wrong or bogus on-disk disklabels.
Once that is clear, <sys/disk.h> which is included in the drivers
no longer need to pull <sys/disklabel.h> and <sys/diskslice.h> in,
the few places that needs them, have gotten explicit #includes for
them.
The disklabel inside struct disk is now only for internal use in
the disk mini-layer, so instead of embedding it, we malloc it as
we need it.
This concludes (modulus any mistakes) the series of disklabel related
commits.
I belive it all amounts to a NOP for all the rest of you :-)
Sponsored by: DARPA & NAI Labs.
RXSTATE to STOPPED, but to WAIT. This should fix hangs which
could only be solved by replugging the cable.
Submitted by: jhb
Reviewed by: phk
MFC after: 2 weeks
Rename diskerr() to disk_err() for naming consistency.
Drop the by now entirely useless struct disklabel argument.
Add a flag argument for new-line termination.
Fix a couple of printf-format-casts to %j instead of %l.
Correctly print the name of all bio commands.
Move the function from subr_disklabel.c to subr_disk.c,
and from <sys/disklabel.h> to <sys/disk.h>.
Use the new disk_err() throughout, #include <sys/disk.h> as needed.
Bump __FreeBSD_version for the sake of the aac disk drivers #ifdefs.
Remove unused disklabel members of softc for aac, amr and mlx, which seem
to originally have been intended for diskerr() use, but which only rotted
and got Copy&Pasted at least two times to many.
Sponsored by: DARPA & NAI Labs.
previous commit:
Include <sys/mutex.h> and its prerequisite <sys/lock.h> instead of
depending on namespace pollution in <sys/buf.h>. Only do this in the
__FreeBSD_version > 500000 case although the __FreeBSD_version < 500000
case has already rotted.
(what we want to mask is the ATA interrupts, which run at level splbio),
and add interrupt masking around the statement that modifies the
request queue for a SIM.
This resolves problems reported by users under heavy ATAPI load.
Reviewed by: roberto
reprobe code working. This bogusness was thrust upon me.
o Don't delete the device if no drivers attach. I had thrust this bogusness
upon others.
These two changes make kldload of a pccard driver work again.
cards to test; however the submitter reports that this patch works
with the on-board interface on the IBM x235 server.
Submitted by: Jung-uk Kim <jkim@niksun.com>
MFC after: 1 month
- Get the initial mode from the prom settings and don't clobber the mode
on open.
- Copy output into an internal ring buffer instead of accessing the tty
outq directly in the interrupt handler. This fixes a problem where
garbage would show up in the output stream.
- Reset the console port completely and reprogram all the parameters
before enabling it. This fixes seemingly random hangs on startup
when using a fast interrupt handler.
- Add minimal locking in place of spls.
- Remove dead code and minor cleanups.
any machine dependent initialization. This allows the MD code to set the
interrupt routing model so that PCI interrupts are routed correctly when
using an APIC or SAPIC for example.
In this installment, we learn that it is bad to access registers that
are only defined for mfc cards in the interrupt handler when we do not
in fact have a mfc card. For MFC cards, we'll only call the ISR if
the this card interrupted bit is set. For non mfc cards (which are
basically 90% of pccards in use), we always call the ISR and avoid
touching the suspect registers. We always pacify the bit in the MFC
case on the off chance that will help in the itnerrupt handler not
being registed.
when the first PCI bus attaches.
- Create /dev/pci during MOD_LOAD as well.
- Destroy /dev/pci during MOD_UNLOAD (not that you can kldunload pci, but
might as well get the code right)
PUC devices live on pccard or pci so INTR_FAST is never really an option.
Don't try to register the interrupt as fast and don't allow the children
to do so either.
- add bus capabilities into the driver, so that it is possible for a radio
driver to attach to it to use shared resources of fm801 chip. The radio
driver itself will be committed later.
MFC after: 1 week
a) we don't believe what the board tells us all the time (if the BIOS
hasn't run, port page 2 and port page 0 tend to be garbage)
b) add the missing code to set parameters for the SPI cards.
MFC after: 0 days
on -current. Actually copy in data from userspace to kernel in the
linux-compat ioctl path. Make sure ioctl sizes are as expected in the handler
functions.
Reviewed by: rwatson
right places, and so it's sorted consistently with how all the other N-hundreds
of files ding this do it.
Submitted by: Hiten Pandya <hiten@uk.FreeBSD.org>
Don't expect all RIDs to be PCI rids. The previous code made at
least 1 mistake, even for PCI.
Give the card definitions a chance to specify a init function.
Use this instead of the gross superio hack.
Move the win877 init function to puc_pci.c where it belongs.
RIDs can actually be zero, don't set badmuxed if so.
Set a less incorrect end for the construct SYS_RES_IOPORT entries,
I guess both sio and lpt happen to use 8 IO ports, but that shouldn't
really be hardcoded this way.
Fixup puc_pccard.c to match.
We're getting closer.
Don't set the CCR_OPTION register when registering/deregistering
interrupts unless the card is a MFC card. This makes a lot of cards
work that didn't work before. These bits are only defined for MFC
cards.
Remove COOKIE_FOR_WARNER kludges that phk introduced.
Add more debug info.
Annoy the purists by committing two minor style nits at the same time.
Many thanks to phk. He tracked this problem down to what was screwing
things up, so fixing it became trivially easy once the problem was
understood.
This ensures that we don't enter our interrupt handler until
all OSM components it might reference have been fully initialized
during attach.
Remove vestiges of untagged queue handling.
Add hints to ahd_get_scb() so it knows what type of SCB collision
management to perform for each new transaction.
Properly disable/enable IU_REQ with changes in tagged queuing and
disconnection settings passed in by CAM.
Uninline some routines that are just too big to be inlined.
Add some helper macros for SCB ID collision management.
Use a hardware SCB rather than a full SCB for the "next
SCB to queue" sentinal.
Update for new "high SCBID bit" qoutfifo delivery scheme.
If interrupts are disabled on the card, don't bother running
our interrupt handler. Our handler was called due to a shared
interrupt, and the card's interrupts are explicitly disabled
to prevent entry into our interrupt handler.
functions for register pretty-printing.
Implement "top bit of SCBID is valid bit" qoutfifo delivery scheme.
"the the" -> "the".
Remove old and never used tag collision chain handling in the
sequencer. Tag collisions are never allowed to get as far as
on the controller.
Simplify busy target table handling routines.
Update comments to reflect reality.
Add support for catching more protocol violations.
Correct a bug in data fifo handling in mixed packetized and
non-packetized environments. SG_STATE must be cleared even
if an SG fetch is not in progress at the time of FIFO shutdown
or we may confuse the non-packetized transaction idle-loop.
busy target table addressing changes, our qoufifo scheme,
and long lun support.
Drop bus reset hold delay to 25us.
Remove chip workarounds for revisions that never went to
production.
Add aic7901A identification information.
Remove untagged queue logic.
Push protocol violation handler to its own routine. We now
properly detect and recovery from the following target induced
protocol violations:
o Unexpected or invalid non-packetized Relesection
o Command complete with no status message
o Good Status after incomplete cdb transfer
Add an SCB collision avoidance algorithm that allows us to
use all 512 SCBs for non-packetized operations. There is
still the possibility of running out of SCBs with non-colliding
tag identifiers, but the algorithm ensures that the stall will
be rare and short lived.
Convert to a read-only algorithm for validing entries in the
qoufifo. The sequencer now toggles the high bit of the SCB
identifier on each wrap around of the qinfifo. If the high
bit doesn't match the expected value for this pass of the
qoufifo, the entry is not valid. This has the benefit of
working on machines that have large granularity cache write
back semantics without requiring any additional memory.
Remove lots of code related to untagged SCB queues. Since
these controllers can keep a fully busy target table, we
will never have untagged SCB queues.
Lots of improvements to diagnostic logging.
Clarify some comments.
Don't clear BUSFREE interrupt enable in SIMODE1 in the SELTO
handler. Just clearing the interrupt status is sufficient and
this avoids the chance of disabling busfree detection in connection
that occurs while we are handling the busfree interrupt.
Clear all possible interrupt sources when handling a busfree
interrupt. The hardware clears some but not all of them.
Don't panic if we get into the default SCSIINT handler.
Dump the card state and clear all interrupt sources in the
hope that we can continue.
LASTPHASE != PREVPHASE. Use the correct PREVPHASE for testing
against values in the PERRDIAG register.
According to SPI4, the bus free that is required after certain
PPR negotiations will only occur at the end of all message phases.
Handle the bus free if it occurs after a transaction in either
the message-in or message-out phases. The busfree can also occur
if the status of IU_REQ changes due to a WDTR or SDTR message.
We now set the expect busfree flag in ahd_set_syncrate so that
it works regardless of message type.
Correct a problem with missing certain busfree events. The
chip supports single-stepping even if a SCSIINT is pending.
This obviates the need to clear all of the SCSI interrupt enables
prior to single stepping. Since ENBUSFREE can only be disabled
manually and not re-enabled, avoiding touching this bit in the
single-step case yields reliable bus free detection.
Enhance ahd_clear_intstat to clear all SCSIINT sources.
Only use ahd_update_pending_scbs() if we are active on the
bus. We cannot modify the "MK_MESSAGE" bits on SCBs in the
execution queue if a selection might be in process since
the sequencer uses this bit to detect PPR negotiation to
a target with an outstanding IU_REQ agreement.
Allocate the SCB delivery mechansim's sentinal SCB specially
so we don't waste a valid SCB for this task.
Move tranceive state settle logic to ahd_chip_init() since
this needs to occur after every chip reset, not just the
chip reset that happens during primary driver initialization.
Correct a bug with transmitting lun information in packetized
connections.
Restrict busy target table operations to the range of luns
that can be used for non-packetized connections. Larger luns
can only be accessed in packetized mode.
Correct a busy target table addressing bug.
Be more careful about how we shutdown the DMA engines during
bus reset events.
Only freeze the SIMQ once regardless of the number of bus
reset events that occur while we are polling for the resets
to stop.
Don't rely on the sequencer remaining paused() during our
reset poll. It is safe for the sequencer to run during this
time, and many callers to the bus reset code would need to
be modified to make this assumption universally true.
Even if we are not going to clobber SCB state when an auto-request
sense SCB has a check condition, we must still unfreeze the queue.
Re-arrange the BAD STATUS handler to handle this case appropriately.
Modify the SCB download size depending on whether long luns are
being stored in the SCB.
Add ahd_print_register() for pretty printing register diagnostics.
Don't trust that the flexport logic to detect the presence of
a seeprom is available. It may not be on some motherboard
implementations.
"the the" -> "the"
our interrupt handler. Our handler was called due to a shared
interrupt, and the card's interrupts are explicitly disabled
to prevent entry into our interrupt handler.
Set the AHC_LSCBS_ENABLED softc flag appropriately.
Convert to using softc storage for our seeprom data.
Break seeprom parsing out into a separate routine.
Change our policy in regards to AHC_SPIOCAP so that we
will allow auto-termination to take place on some aic7855
based cards.
Remove initialized but never really used variables.
Use "offset == 0" not "period == 0" to denote async trasnfers.
Implement TARG_IMMEDIATE_SCB non-disconnected target mode
SCB delivery scheme.
In our timeout handler, don't rely on the phase already being
set to denote an active connection. IDENTIFY_SEEN is more
than sufficient.
Verify that the softc passed in ahc_detach is still known
to the driver before blindly using it.
functions for register pretty-printing.
Only clear SELDO once we've recorded enough information for
the host to understand that the connection is valid. The
host uses the SELDO status as a handshake to close this
race window.
Correct a bug in target mode handling of non-disconnected
transactions. The host would indicate the correct SCB to
DMA by setting the SCB id in the currently selected hardware
SCB. Unfortunately, we would then immediated allocate a
hardware SCB which, depending on the access patern might not
be the same hardware SCB that the host setup for us. Avoid
this by having the host put the SCBID into scratch ram.
Document the SXFRCTL2 register found on U2 and U160 controllers.
Overload the MWI_RESIDUAL field for use as the SCB to be downloaded
for "immediate" (or those without the disconnect privledge)
transactions.
Add scratch ram locations for the 274X that give us a bit more
information including whether to enable extended translation.
value slipped in from a debugging session.
Add AHC_LSCBS_ENABLED and AHC_SCB_CONFIG_USED ahc_flags which
allow for some code to move to the core.
Remove extern for ahc_syncrates[]. The OSMs no longer need
direct access to this array.
Add serial eeprom field to the ahc softc.
Prototype ahc_search_untagged_queues() and ahc_print_register().
Convert to AHC_SHOW_XXX debug option format.
Switch to using the same AHC_SHOW_XXX format as the ahd driver.
Always give the target a MSG_INITIATOR_DET_ERR for unexpected
DT or ST phase errors.
Add AHC_SHOW_SELTO diagnostics.
Force renegotiation whenever an unexpected bus free occurs
to rule out a negotiation mismatch as the cause for the error.
Use "offset != 0" as an intenal indicator of "async" rather than
using a period of 0.
In ahc_fetch_devinfo(), correct a bug in getting "our id" as
target. We weren't looking at all the SEQ_FLAGS that indicate
that we are still in a selected rather than reselected state.
Add support for the AHC_SHOW_MESSAGES debugging option.
If ahc_parse_msg() tells us to terminate the message loop,
do so without acking the message. The message may be one
that the sequencer needs to handle on its own.
In ahc_parse_msg() return MSGLOOP_TERMINATED for all messages
the sequencer handles.
Allocate storage for, and track, seeprom contents in our softc.
Touch all SCB bytes to avoid parity errors should one of our
debugging routines read an otherwise uninitiatlized byte.
S/G lists must be 8 byte aligned. Reflect this in our DMA tag.
"the the" -> "the" in a comment
When pausing the card to perform error recovery, ensure that we
are not in the process of being selected or have just been selected
but have not yet handled that selection. This leaves only one other
race window, in the command complete handler, that needs to be fixed
to make recovery 100% bullet proof.
Convert a few straglers from bsd u_intX_t to inttypes uintX_t.
Remove unused variables.
Split out searching of the untagged holding queues to its own
routine. In certain recovery scenarios, we want to just
remove entries in the untagged queue without touching related
transactions that are in the QINFIFO or WAITING queues that are
searched by ahc_search_qinfifo().
Add an implementation of the ahc_print_register() routine which
"pretty prints" registers. The extra bloat in the form of string
tables for this feature is controlled by the AHC_REG_PRETTY_PRINT
option.
Fix a few bugs in ahc_enable_lun() that could prevent controllers
lacking the multiple-target-id feature from changing "our id" on
the fly. Add a large comment to this section while I'm here
describing the restrictions on "id switching".
Honor the extended translation setting for EISA cards now that
I've determined where this information is kept.
Defer card interrupt enabling to the OSM since it may have
some initialization to perform that must occur before interrupts
can be enabled.
Fix device hints entry for disabling acpi(4).
This also should fix the arbitration with apm(4) when both drivers
are enabled.
Note that your /boot/device.hints needs to be updated if you want to
stop auto-loading acpi.ko or disable acpi(4).
attach. If it can't get that (highly likely if loaded as a module on
a system that's been up for a while), give a more descriptive error
message.
Also clean up some nearby style nits.
MFC after: 2 days
Replace dual copyright with a plain BSD style copyright assigned
to LSI Logic. This is still within the intents of express consent
from LSI.
MFC after: 2 days
specifically allows for (via 'BSD Style' licensing) source && binary
redistribution.
Pointy hat to: Matt, for not getting this done ahead of time.
MFC after: 2 days
circumstances. The problem was only reported with -stable, but it's
obviously wrong in -current also. MFC is forthcoming.
Submitted by: doconnor@dsoft.com.au
Recent version of ACPI CA returns the package object which contains
object reference elements if the elements are named objects.
We need to be careful when you use acpi_ForeachPackageObject() in new
code...
We are having panics with the driver under stress with jumbo frames.
Unfortunately we didnot catch it during our regular test cycle.
I am going to MFC the backout immediately.
- Add an ACPI PCI-PCI bridge driver (the previous driver just handled
Host-PCI bridges) that is a PCI driver that is a subclass of the generic
PCI-PCI bridge driver. It overrides probe, attach, read_ivar, and
pci_route_interrupt.
- The probe routine only succeeds if our parent is an ACPI PCI bus which
we test for by seeing if we can read our ACPI_HANDLE as an ivar.
- The attach routine saves a copy of our handle and calls the new
acpi_pcib_attach_common() function described below.
- The read_ivar routine handles normal PCI-PCI bridge ivars and adds an
ivar to return the ACPI_HANDLE of the bus this bridge represents.
- The route_interrupt routine fetches the _PRT (PCI Interrupt Routing
Table) from the bridge device's softc and passes it off to
acpi_pcib_route_interrupt() to route the interrupt.
- Split the old ACPI Host-PCI bridge driver into two pieces. Part of
the attach routine and most of the route_interrupt routine remain in
acpi_pcib.c and are shared by both ACPI PCI bridge drivers.
- The attach routine verifies the PCI bridge is present, reads in
the _PRT for the bridge, and attaches the child PCI bus.
- The route_interrupt routine uses the passed in _PRT to route a PCI
interrupt.
The rest of the driver is the ACPI Host-PCI bridge specific bits that
live in acpi_pcib_acpi.c.
- We no longer duplicate pcib_maxslots but use it directly.
- The driver now uses the pcib devclass instead of its own devclass.
This means that PCI busses are now only children of pcib devices.
- Allow the ACPI_HANDLE for the child PCI bus to be read as an ivar
of the child bus.
- Fetch the _PRT for routing PCI interrupts directly from our softc
instead of walking the devclass to find ourself and then fetch our
own softc.
With this change and the new ACPI PCI bus driver, ACPI can now properly
route interrupts for devices behind PCI-PCI bridges. That is, the
Itanium2 with like 10 PCI busses can now boot ok and route all the PCI
interrupts. Hopefully this will also fix problems people are having with
CardBus bridges behind PCI-PCI bridges not properly routing interrupts
when ACPI is used.
Tested on: i386, ia64
driver. This driver overrides the probe, attach, and read_ivar methods.
If the parent bridge is an ACPI PCI bridge, then the probe routine will
match, otherwise it will fail. It tests this by seeing if it can get
the ACPI_HANDLE ivar from the bridge device.
In the attach routine, it uses pci_add_children() to add all the child
devices (but with a slightly larger ivar so it can store ACPI_HANDLE's
for child devices) and then walks through the ACPI namespace below the
bus device to cache ACPI_HANDLE's for all child devices present in the
namespace. It does this by comparing the pci slot and function to the
address encoded in _ADR of the devices in the ACPI namespace.
The read_ivar routine passes most requests off to pci_read_ivar()
and adds a new request so that the ACPI_HANDLE for a child device can
be read.
To add proper power support the power methods can be overridden as well,
but that is not currently implemented. Also, there are cases where a
device may show in the ACPI namespace as a PCI device that the PCI probe
does not find. Currently such devices are ignored.
Tested on: i386, ia64
OOP speak, you would mark these as 'protected' members. Specifically:
- Make the pcib_softc struct public so it can be used by subclasses.
- Make pcib_{read,write}_ivar(), pcib_alloc_resource(), pcib_maxslots(),
and pcib_{read,write}_config() globals that can be used by subclasses.
- Make the pcib devclass a global variable.
- Move most of the pcib_attach() function into a global
pcib_attach_common() function that can be called by the attach routines
of subclasses.
Tested on: i386, alpha, sparc64, ia64
- Make the pci devclass a global variable.
- Add child devices in pci_attach() instead of pci_probe(). Change
pci_probe() to just check for a valid bus number from the associated
bridge and return -1000 if successful. This allows subclasses of the
PCI bus driver to override the generic driver.
- Move the code to load the vendor data into its own public function.
Really though, doing this at attach is just plain wrong. This should
really be done in the module load routine instead. As a side effect,
the 'busno' variable in pci_attach() is now no longer static (minor
bug that was harmless so far.)
- Change pci_add_children() to take an extra argument that is the size of
the device info structure passed to pci_read_device() and make it public
so subclasses of the PCI bus can call it in their attach routines.
- Move the bits to attach a probed PCI child to a PCI bus into a global
pci_add_child() function. This will allow subclasses that can detect
a PCI device not found in the normal PCI probe to add those devices in
their own attach routine. (I have seen this in the ACPI tree on my
laptop for example.) As a side effect, change the static function
pci_add_resources() to get the busno, slot, and func from the passed
in dinfo structure instead of requiring them as function arguments.
Tested on: i386, alpha, ia64, sparc64
LNK device (interrupt source provider sort of) is present before using it,
but the code actually tested the status (_STA) of the PCI bridge device
doing the routing, not the actual LNK device. Fix it to check the status
of the LNK device.
pmap_zero_page() and pmap_zero_page_area() were modified to accept
a struct vm_page * instead of a physical address, vm_page_zero_fill()
and vm_page_zero_fill_area() have served no purpose.
Attempt to determine what function of AUX_OUT is: "True line level
out", "Headphone out", or "4-Channel out" and frig OSS mixer label
accordingly.
Addresses problem raised by Randy Bush on -multimedia of not being
able to hear audio on ich2 m/b which was eventually found to be
because the mixer monitor value was 0. On this h/w the label
"monitor" should now be presented as the marginally more intuitive
"ogain".
We now also read configuration information for the SCSI cards- this allows
us to try and say what the speed settings now are.
Start, but not yet complete, the process of reorgs && #defines so that we
can backport to RELENG_4 pretty soon.
but since pc hardware only allows one AT-style keyboard controller, this
doesn't seem particularly urgent. (I do not know what the old sunriver
remote keyboard/mouse/vga cards do, that might be an exception).
little more than a place holder, because nothing actually counted the
number of 'sc' units to compare it against NSC. A bit more work here
is needed so that the scaling of SC_MAX_HISTORY_SIZE and extra_history_size
goes up when more sc units are added. But, it does not appear that we can
have more than one console yet, so it does not seem particularly urgent.
opening the device, eg one read only and one write only, and the
reference count being non-zero when both exit rendering device
permanently busy.
PR: kern/35004
Submitted by: Bill Wells
MFC after: 3 days
load f/w images > 0x7fff words), set ISP_FW_ATTR_SCCLUN. We explicitly
don't believe we can find attributes if f/w is < 1.17.0, so we have to
set SCCLUN for the 1.15.37 f/w we're using manually- otherwise every
target will replicate itself across all 16 supported luns for non-SCCLUN
f/w.
Correctly set things up for 23XX and either fast posting or ZIO. The
23XX, it turns out, does not support RIO. If you put a non-zero value
in xfwoptions, this will disable fast posting. If you put ICBXOPT_ZIO
in xfwoptions, then the 23XX will do interrupt delays but post to the
response queue- apparently QLogic *now* believes that reading multiple
handles from registers is less of a win than writing (and delaying)
multiple 64 byte responses to the response queue.
At the end of taking a a good f/w crash dump, send the ISPASYNC_FW_DUMPED
event to the outer layers (who can then do things like wake a user
daemon to *fetch* the crash image, etc.).
fast posting command completion, and fast post CTIO completion,
the upper half of Risc2Host is a copy of mailbox #1- *not*
mailbox #0.
MFC after: 1 day
accept an 'active_cred' argument reflecting the credential of the thread
initiating the ioctl operation.
- Change fo_ioctl() to accept active_cred; change consumers of the
fo_ioctl() interface to generally pass active_cred from td->td_ucred.
- In fifofs, initialize filetmp.f_cred to ap->a_cred so that the
invocations of soo_ioctl() are provided access to the calling f_cred.
Pass ap->a_td->td_ucred as the active_cred, but note that this is
required because we don't yet distinguish file_cred and active_cred
in invoking VOP's.
- Update kqueue_ioctl() for its new argument.
- Update pipe_ioctl() for its new argument, pass active_cred rather
than td_ucred to MAC for authorization.
- Update soo_ioctl() for its new argument.
- Update vn_ioctl() for its new argument, use active_cred rather than
td->td_ucred to authorize VOP_IOCTL() and the associated VOP_GETATTR().
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
when this is needed. Work around bogus second PHY in the DFE-580 card
via a change in the if_ste.c driver.
Suggested by: jdp
Reviewed by: jdp
MFC after: 3 days
elimiates the driver lockup problem reported by many.
Concepts used were taken from Via's if_fet driver. Verification
and implementation were done by Thomas Nystrom.
Submitted by: Thomas Nystrom <thn@saeab.se>
MFC after: 3 days
This is an architecture that present a thing message passing interface
to the OS. You can query as to how many ports and what kind are attached
and enable them and so on.
A less grand view is that this is just another way to package SCSI (SPI or
FC) and FC-IP into a one-driver interface set.
This driver support the following hardware:
LSI FC909: Single channel, 1Gbps, Fibre Channel (FC-SCSI only)
LSI FC929: Dual Channel, 1-2Gbps, Fibre Channel (FC-SCSI only)
LSI 53c1020: Single Channel, Ultra4 (320M) (Untested)
LSI 53c1030: Dual Channel, Ultra4 (320M)
Currently it's in fair shape, but expect a lot of changes over the
next few weeks as it stabilizes.
Credits:
The driver is mostly from some folks from Jeff Roberson's company- I've
been slowly migrating it to broader support that I it came to me as.
The hardware used in developing support came from:
FC909: LSI-Logic, Advansys (now Connetix)
FC929: LSI-Logic
53c1030: Antares Microsystems (they make a very fine board!)
MFC after: 3 weeks
code to do it when the bios doesn't do it for us, flag it. Then, when
we dealloc, do an equal kludge to get rid of the address. This should
address the can't get IRQ and panic bug in a more graceful way.
# really should write a dealloc routine and just call it instead, since
# this might not fix things in the kldunload case.
The CAM<>ATAPI layer was submitted by "Thomas Quinot <thomas@cuivre.fr.eu.org>"
changes form the version on the net by me (formatting, ability to be used
alone without the ATAPI native device driver, proper speed reporting...)
See /sys/conf/NOTES for usage.
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
PR40430 by "Peter Haight <peterh@sapros.com>" that has semilar patches
included and which I merged with my own work.
HW sponsored by: FreeBSD Foundation & FreeBSD Mall Inc
Enjoy!
- bus_space'ify
- generate fake ethernet address using read_random() instead of reading
from timer i/o ports
Other minor fixes:
- remove "hack" in connect_to_master()
- use M_ZERO
- remove unused variable in sbni_ioctl()
- properly release irq in sbni_attach_isa() on attach errors
and the AT24C08 small serial flash parts. We still report these as
the same part (since we group things already), but now we recognize
the small serial versions as well.
firmware revision as well (not sure which firmware versions are needed
for this, but the 6.x and 8.x 'software' versions that I have seem to
support it).
Add dBm comm quality RID. This is like the normal comm quality rid,
except the signal and noise numbers are normalized to dBm. Some
revisions of the prism firmware, however, don't support this RID, and
some that do support it return 0 for quality and/or noise. Your
milage may vary.
Also take this chance to cleanup the code in fxp_intr_body.
Add a missing block of code to disable interrupts when
reinitializing the interface while doing polling (the RELENG_4
version was correct).
MFC after: 3 days
cards. Since the firmware is hard coded into the kernel, I've made it
a kernel option (WI_SYMBOL_FIRMWARE).
Note: This only downloads into the RAM of these cards. It doesn't
download into FLASH, and is somewhat limited. There needs to be a
better way to deal, but this works for now. My Symbol LA4132 CF card
works now.
Obtained from: NetBSD
sizes. Previously, the end result was at the mercy of the card's default
setting. This change will reduce the number of buffer underruns for
some users.
PR: kern/37929
Submitted by: Thomas Nystrom <thn@saeab.se>
MFC after: 7 days
controller. Some testing has already been done, but its still greenish.
RAID's has to be setup via the BIOS on the SuperTrak, but all RAID
types are supported by the driver. The SuperTrak rebuilds failed arrays
on the fly and supports spare disks etc etc...
Add "device pst" to your config file to use.
As usual bugsreports, suggestions etc are welcome...
Development sponsored by: Advanis
Hardware donated by: Promise Inc.
debugging levels to off by default. Now that debug levels can be
tweaked by sysctl we don't need to go through hoops to get the
different usb parts to produce debug data.
frees it again. The idea was to perform M_WAITOK allocations in a
process context to reduce the risk of later interrupt-context
M_NOWAIT allocations failing, but in fact this code can be called
from contexts where it is not desirable to sleep (e.g. if_start
routines), so it causes lots of witness "could sleep" warnings.
is that some cards built around fm801 chip have the same device ID, only
have radio tuner onboard, but no sound capabilities. Therefore, with such
card inserted and `device pcm' in kernel the user has a big problem, as
the fm801 driver effectively hangs the machine when trying to initialise
nonexistent ac97 codecs (it does 500 retries with 1 second interval!).
It would be better if MediaForte's engeneers were smart enough to put
different device ID into such cards, but it isn't an option.
MFC after: 2 weeks
problems with the firmware and will result in a) poor performance and
b) the inability to associate certain types of cards (most notibly
cisco).
Idea obtained from OpenBSD, but I implemented it by clearing the
IFF_PROMISC flag rather than the refusing to honor it downstream.
1.131 is slightly broken, and I would commit the fix to that here, but it
has been reported that any deviation from the original code is causing
problems with some 82557 chips, causing them to lock hard.
Until those issues have been figured out, going back to the original
code is the best plan.
Frustrated: Silby
o Rename the insanely long PCIC bridge ids.
o Add my copyright to pccbb.c
o Add support for the TI-1510, TI-1520 and TI-4510 series of upcoming
bridges.
o Init MFUNC if it is zero and the TI part has a MFUNC register
at offset 0x8c (1030, 1130 and 1131 don't have anything there, the
1250,1251,1251B and 1450 have a different thing there. The rest
have it. TI is likely to only do MFUNC from now on. The IRQMUX
in the 1250 series of chips needs no tweaks.
o Adjust to new exca interface.
o Add comments about TI chips that I learned in talking to an
engineer at TI.
o Add register definitions for MFUNC.
o Create CB_TI125X chipset type.
o Protect .h against multiple includes.
o eliminate the pointers to the read/write routines. The
bus_space_read routines can cope since we have the offset
field.
o Print a warning if the requested map address is > 16M and
your chipset doesn't support the extended ExCA registers.
of the Netgear GA302-T. I changed the symbolic names in the
submitter's patch to reflect the part number of the chip instead
of the board.
PR: kern/38988
Submitted by: Brad Chapman <chapmanb@arches.uga.edu>
MFC after: 2 days
Through the PITA of endiannness, clock has to be MHz freq << 8.
Don't trust NVRAM on SBus cards.
Set a default initiator ID sensibly.
SBus/ISP now working, what with the change to sbus.c earlier today.
flags include INTR_MPSAFE. Put the flags in a common place so that
both isp_sbus && isp_pci DTRT.
In isp_mbxdma setup, drop any locks prior to calling things like
bus_dmatag_create. This gets rid of these obnoxious WITNESS messages
about 'sleeping with locks held' blah blah blah blah blah.
has been specified through /boot/loader.conf as opposed to setting it
in /etc/sysctl.conf. Only PCMDIR_PLAY channel can be used as a parent
of virtual channel. Do not initialize a new vchan for a given physical
channel if other physical channel already has one created.
PR: 31597
Approved by: obrien (mentor)
o Honor NE2000DVF_{AX88190,DL10019} flags by setting the ED_FLAGS_xxxx
flag.
o Mark linksys combo_ecard as ax88190
o Set the type_str to AX88190 for the ax88190 cards.
This fixes ax88190 based cards, for the most part, but doesn't seem to fix
the mii based dl10019 cards (aka linksys cards).
This is required for some Thinkpad (and maybe VAIO) machines to wake
the system up from sleep.
Currently partially implemented, more complete implementation will come later.
pci support. This really needs to be fixed properly some day, but judging
by the fact that the nopci case hasn't compiled for quite a while, there
does not seem to be much urgency.
Reviewed by: sos
This driver actually works slightly better on -stable than on -current
(the system locks on detach on -current), so it should be MFC'd somewhat
sooner.
This driver currently points out a difficulty in the sound device framework.
The PCM unregister routine is allowed to refuse the detach if the device is
in use. In the case of a USB device, however, this unregistration is much more
mandatory in nature, since the device is *actually* gone when this call is
made. The sound subsystem really should not refuse an unregistration and
should take its own steps to reject further I/O. As a result, if you detach
a USB sound device while it is in use, you can expect a panic shortly
thereafter.
This device cannot currently record audio. Some routines are unwritten as
of yet in uaudio.c to support recording.
This device hangs my -current box on detach. I don't know why. This does
not happen on my -stable machine.
Obtained from: Hiroyuki Aizu
MFC after: 2 weeks
in the .h file. Make it static __inline to make sure that it doesn't
wind up defined in any files.
Also, fix a typo that said null_do_attach instead of null_do_probe.
1.93; henning; MA401RA wi card
1.92; millert; elsa XI-325 wi card
1.91; fgsch; gemplus cpr400 smartcard reader
1.90; mickey; Nokia c110/c111 is prism2 card
1.89-1.86 (similar to what we do already)
The value we use is still questionable for 440BX chipsets.
- When flushing the TLB just toggle the bit in question instead of writing
a magic value that could trash other unrelated bits.
because the previous interface handle gets freed when the config
number is set. This fixes a problem where memory could be accessed
after it was freed when the interface was ifconfig'd up.
Reviewed by: n_hibma
one out of a block cipher. This has 2 advantages:
1) The code is _much_ simpler
2) We aren't committing our security to one algorithm (much as we
may think we trust AES).
While I'm here, make an explicit reseed do a slow reseed instead
of a fast; this is in line with what the original paper suggested.
- always reinitialize the rx descriptors, even if the mbuf is kept.
This should fix the hangs on ifconfig that were observed
- on an rx overflow, reinitialize the descriptor so that the interface
will not hang
- correct some bus_dmamap_sync() calls
- correct some debug messages
- some minor nits
o Assert that the page queues lock is held in vm_page_unwire().
o Make vm_page_lock_queues() and vm_page_unlock_queues() visible
to kernel loadable modules.
This code does not imply that SBus cards work yet. They hang for me.
But I can't netboot the latest snapshot on my ultra1e, and things
hang at bus_setup_intr time.
Since I'm offline for a while, I thought I'd toss this in in case somebody
else who has a bit better luck wants to fart around with it. Please try
and wait until I get back to check things in.
- Remove some obsolete code (NetBSD gem.c r1.12)
- Clean up how the local MAC address is programmed (NetBSD gem.c r1.13)
- Make the driver work on PowerMacs with gigabit interfaces
(NetBSD gem.c r1.14 and r1.15, gemreg.h r1.3 and r1.4, gemvar.h r1.6 and 1.7)
- Suppress RX_MAC interrutps regarding the FRAME_COUNT register.
(NetBSD gem.c r1.16 and r1.17)
- Fix receiver lockups. (NetBSD gem.c r1.18, gemvar.h r1.8)
- Distinguish between Apple and Sun variants (NetBSD if_gem_pci.c r1.9)
Reviewed by: tmm
Obtained from: NetBSD
like this can be emulated by VT_SETMODEing to VT_PROCESS and never
releasing the vty, but this has a number of problems, most notably
that a process must stay resident for the lock to be in effect.
Reviewed by: roam, sheldonh
that the attach succeeded. (Fixes a potential panic for devices
that fail to attach properly and are subsquently unplugged and then
plugged back in again.)
Oops; I forgot for previous delta... If we're and FC or ULTRA2 or better
card, we can have a 1024 element request queue instead of 256.
MFC after: 1 week
Remove sim queue freezes for resource shortages. I've had too many
strange race conditions where I freeze on a resource shortage but
never get unfrozen.
Consolidate the remaining sim queue freeze condition (for loopdown)
into an inline with debug messages that allows us to track problems
at ISP_LOGDEBUG0 level easier. Change a bunch of debug messages about
loop down/up conditions to ISP_LOGDEBUG0 level.
Remove dead isp_relsim code.
Change some internal flag stuff for efficiency.
Complain vociferously if we try and use our FC scratch area while it's
busy being used already (I mean, if we don't have solaris' ability
to sleep as an interrupt thread which would allow us to just use
a p/v semaphore, at least *say* when you've just borked yourself).
Add infrastructure to allow overrides of hard loopid && initiator
id from boot variables.
Fix the usual quota of silly bugs:
+ 'ktmature' needs to be per-instance. Argh.
+ When entering isp_watchdog, set intsok to zero, preserving
old value to restore later. It's not nice to try and sleep
from splsoftclock.
+ Fix tick overflow buglet in checking timeout value.
MFC after: 1 week
turns out that there's something of a hole in our new fabric name
server stuff. We ask the name server for entities that have
registered as a specific type. That type is FC-SCSI. If the entity
hasn't performed a REGISTER FC4 TYPES, the fabric nameserver won't
return it.
This brings this driver to a bit of a fork in the road as to what
the right thing to do is. For servicing the needs of accessing
FC-SCSI devices, this method is fine, and to be preferred. It is
extremely unlikely we're interested in fabric devices that *don't*
register correctly. If I ever get around to adding an FC-IP stack,
then asking for devices that have registers as FC-IP types is also
the right thing to do.
So- asking the fabric nameserver for a specific type is fine, *as
long as you are only interested in specific types*. If, on the other
hand, you want to create (as for management tool support) a picture
of everything on the fabric, this is *not* so fine. There are a
large class of FC-SCSI *initiators* who *don't* correctly register,
so we never will *see* them.
Is this a problem? Yes, but only a little one. If we want to do such
management tool support, we should probably run a *different* fabric
nameserver query algorithm. Better yet, we should talk to the management
nameserver in Brocade switches instead of the standard FC-GS-2 fabric
nameserver (which can be unwieldy).
Other changes: if we've overrrides marked, don't set some default
values from reading NVRAM. This allows us to override things like
EXEC throttle without having to ignore NVRAM entirely.
MFC after: 1 week
internal PHY on the 3COM 3C905B and 3C905C parts, however I've rigged it so
that xlphy (aka exphy) takes precedence for the time being.
If people try this with their xl cards and decide that it's a better choice,
we can switch this later.
This is the PHY used in various iMacs and possibly other GMAC-equipped
Macintoshes with 10/100 PHYs (the ones with 10/100/1000 appear to use brgphy).
Obtained from: NetBSD
driver. I tried a few obvious experiments, but was unable to make
the 3c996B-T generate correct UDP checksums for transmitted fragmented
packets. I'm not so sure the device is even capable of it.
This fixes NFS over UDP.
MFC after: 1 day
are packets queued for transmission.
This driver is strange -- it never sets IFF_OACTIVE, so all
transmissions always cause a call to fxp_start. However, if the
link gets stuck, there was nothing to reset it, so there was still
a possibility of lockups.
MFC after: 3 days
calibrated. This fixes the problem where playback and recording do
not run at the correct speed. It probably also eliminates the
need for the hacks/workarounds/sysctl's that were previously
devised to deal with this, but I will leave that for a different
time.
Reviewed by: orion
MAKEDEV: Add MAKEDEV glue for the ti(4) device nodes.
ti.4: Update the ti(4) man page to include information on the
TI_JUMBO_HDRSPLIT and TI_PRIVATE_JUMBOS kernel options,
and also include information about the new character
device interface and the associated ioctls.
man9/Makefile: Add jumbo.9 and zero_copy.9 man pages and associated
links.
jumbo.9: New man page describing the jumbo buffer allocator
interface and operation.
zero_copy.9: New man page describing the general characteristics of
the zero copy send and receive code, and what an
application author should do to take advantage of the
zero copy functionality.
NOTES: Add entries for ZERO_COPY_SOCKETS, TI_PRIVATE_JUMBOS,
TI_JUMBO_HDRSPLIT, MSIZE, and MCLSHIFT.
conf/files: Add uipc_jumbo.c and uipc_cow.c.
conf/options: Add the 5 options mentioned above.
kern_subr.c: Receive side zero copy implementation. This takes
"disposable" pages attached to an mbuf, gives them to
a user process, and then recycles the user's page.
This is only active when ZERO_COPY_SOCKETS is turned on
and the kern.ipc.zero_copy.receive sysctl variable is
set to 1.
uipc_cow.c: Send side zero copy functions. Takes a page written
by the user and maps it copy on write and assigns it
kernel virtual address space. Removes copy on write
mapping once the buffer has been freed by the network
stack.
uipc_jumbo.c: Jumbo disposable page allocator code. This allocates
(optionally) disposable pages for network drivers that
want to give the user the option of doing zero copy
receive.
uipc_socket.c: Add kern.ipc.zero_copy.{send,receive} sysctls that are
enabled if ZERO_COPY_SOCKETS is turned on.
Add zero copy send support to sosend() -- pages get
mapped into the kernel instead of getting copied if
they meet size and alignment restrictions.
uipc_syscalls.c:Un-staticize some of the sf* functions so that they
can be used elsewhere. (uipc_cow.c)
if_media.c: In the SIOCGIFMEDIA ioctl in ifmedia_ioctl(), avoid
calling malloc() with M_WAITOK. Return an error if
the M_NOWAIT malloc fails.
The ti(4) driver and the wi(4) driver, at least, call
this with a mutex held. This causes witness warnings
for 'ifconfig -a' with a wi(4) or ti(4) board in the
system. (I've only verified for ti(4)).
ip_output.c: Fragment large datagrams so that each segment contains
a multiple of PAGE_SIZE amount of data plus headers.
This allows the receiver to potentially do page
flipping on receives.
if_ti.c: Add zero copy receive support to the ti(4) driver. If
TI_PRIVATE_JUMBOS is not defined, it now uses the
jumbo(9) buffer allocator for jumbo receive buffers.
Add a new character device interface for the ti(4)
driver for the new debugging interface. This allows
(a patched version of) gdb to talk to the Tigon board
and debug the firmware. There are also a few additional
debugging ioctls available through this interface.
Add header splitting support to the ti(4) driver.
Tweak some of the default interrupt coalescing
parameters to more useful defaults.
Add hooks for supporting transmit flow control, but
leave it turned off with a comment describing why it
is turned off.
if_tireg.h: Change the firmware rev to 12.4.11, since we're really
at 12.4.11 plus fixes from 12.4.13.
Add defines needed for debugging.
Remove the ti_stats structure, it is now defined in
sys/tiio.h.
ti_fw.h: 12.4.11 firmware.
ti_fw2.h: 12.4.11 firmware, plus selected fixes from 12.4.13,
and my header splitting patches. Revision 12.4.13
doesn't handle 10/100 negotiation properly. (This
firmware is the same as what was in the tree previously,
with the addition of header splitting support.)
sys/jumbo.h: Jumbo buffer allocator interface.
sys/mbuf.h: Add a new external mbuf type, EXT_DISPOSABLE, to
indicate that the payload buffer can be thrown away /
flipped to a userland process.
socketvar.h: Add prototype for socow_setup.
tiio.h: ioctl interface to the character portion of the ti(4)
driver, plus associated structure/type definitions.
uio.h: Change prototype for uiomoveco() so that we'll know
whether the source page is disposable.
ufs_readwrite.c:Update for new prototype of uiomoveco().
vm_fault.c: In vm_fault(), check to see whether we need to do a page
based copy on write fault.
vm_object.c: Add a new function, vm_object_allocate_wait(). This
does the same thing that vm_object allocate does, except
that it gives the caller the opportunity to specify whether
it should wait on the uma_zalloc() of the object structre.
This allows vm objects to be allocated while holding a
mutex. (Without generating WITNESS warnings.)
vm_object_allocate() is implemented as a call to
vm_object_allocate_wait() with the malloc flag set to
M_WAITOK.
vm_object.h: Add prototype for vm_object_allocate_wait().
vm_page.c: Add page-based copy on write setup, clear and fault
routines.
vm_page.h: Add page based COW function prototypes and variable in
the vm_page structure.
Many thanks to Drew Gallatin, who wrote the zero copy send and receive
code, and to all the other folks who have tested and reviewed this code
over the years.
up when operating in PCI-X mode. For some received packets there is
data corruption in the first few bytes in that case. Aligning the
packet buffer eliminates the corruption. With this fix, the code
that offsets the packet buffer up by 2 bytes to align the payload is
disabled for BCM5701s operating in PCI-X mode. On the i386, which
permits unaligned accesses, the payload is left unaligned. On other
platforms, the packet is copied after reception to force alignment
of the payload. Obviously, this work-around reduces performance in
those cases (BCM5701 plus PCI-X) where it is in effect.
MFC after: 3 days
otherwise we might get interrupts and are unable to
handle them properly, which results in a page fault.
PR: kern/39549
Submitted by: Gil Kloepfer <gil@arlut.utexas.edu>
request. We need to eat the MAC address of the packet before we go
looking at the SSID and such. Doing do is sufficient to make Cisco
cards assocaite with prism II cards.
The submitter says that Linux does the same thing.
Submitted by: jhay
This facilitates the use in circumstances where you are using a serial
console as well. GDB doesn't support anything higher than 9600 baud (19k2
if you are lucky), but the console does.
during the previous probe are stale.
What really should be done is route the probe through
device_probe_and_attach bit this is one of those ICBBATIASS (I can't be
bothered as there is a simpler solution). The user can easily replug the
device after kldloading a new device driver.
CAM_QUIRK_HILUN devices we loop thru 32bits of lun. Oops.
Switch to using USEC_DELAY rather than USEC_SLEEP at isp_reset time.
Try to paper around a defect in clients that don't correctly registers
themeselves with the fabric nameserver.
Minor updates for Mirapoint support- they still use code that is not
HANDLE_LOOPSTATE_IN_OUTER_LAYERS, and, surprise surprise, this old
stuff had some bugs in it.
Clean up some target mode stuff.
MFC after: 1 week
topology, speed, loopid, WWPN/WWNN, etc.
Beef up target mode. Add isp_handle_platform_notify_scsi and
isp_handle_platform_notify_fc platform handlers to handle immediate
notifies (isp_handle_platform_notify_scsi is still stubbed out).
In implementation of isp_handle_platform_notify_fc, for IN_ABORT_TASK,
peel off a pending XPT_IMMED_NOTIFY and call xpt_done on it and hope
that somebody upstream is listening.
Make sure on final CTIO2s that we set residual correctly. These are
absolutely crucial. Make sure we set relative offset for each CTIO2
based upon bytes we've already xferred. This is what the private
adjunct datat to the original ATIO is. Note state of command so
we can figure out where to find it if we get an ABORT from the firmware.
Make sure we *always* set CAM_TAG_ACTION_VALID for ATIO2s. Make sure
we keep track of the original lun.
If se sent status (or we're otherwise done with the command), don't
forget to free the adjunct structure.
(so we can, when things get lost, find out who currently is processing
on behalf of this open exchange. Invariably, when things are lost and
wedged, it's CAM).
Keep an atio resource counter locally.
MFC after: 1 week
running ABOUT FIRMWARE with some that were started by BIOS downloads).
Redo CTIO2 dma mapping- use continuation segments instead of multiple
CTIO2s. Thanks to Veritas for sponsoring this work (in a different
context).
MFC after: 1 week
to *not* do flow control based upon resource counts for the firmware.
Increase default immediate notify count to 16.
Change isp_target_async to a function returning an integer.
the necesary uma_zcreate() and uma_zdestroy calls into module loading
handler and the device attach handling.
- Change the related HARP netatm code to use UMA zone functions when
dealing with the zones that were formerly the ATM interface (hea, hfa)
storage pools.
- Have atm_physif_freenifs() now get passed an uma_zone_t so that we can
properly free the allocated NIF's back to their zone.
This should be the last commit to remove any code that makes use of the
netatm storage pool api. I will be removing the api code within the near
future.
Reviewed by: mdodd
handshake between the ISR and the worker thread. Move the mutex lock
so that it only protects the cv_wait. This elimiates the not sleeping
with pccbb1 held messages some people were seeing.
Reviewed by: jhb (at least an early version)
obviously bogous return value of ad1816chan_setformat().
PR: 37932
Submitted by: Martin Kaeske <Martin.Kaeske@Stud.TU-Ilmenau.DE>
Reviewed by: hm
MFC after: 10 days
Fix GCC warnings caused by initializing a zero length array. In the process,
simply things a bit by getting rid of 'struct ng_parse_struct_info' which
was useless because it only contained one field.
But now I'm unbreaking compilation by adjusting these files to the recent
netgraph change.
panic because of a repeat make_dev if/when the device is reattached
to the system.
Remove an "#if __FreeBSD__" in code that's nested under a "#if __NetBSD__"
(*sigh*)
Reported by: Seth Hettich <sjh@whiskey.ucf.ics.uci.edu>
Tested by: Seth Hettich <sjh@whiskey.ucf.ics.uci.edu>
date: 2002/05/28 12:42:39; author: augustss;
Change DMAADDR macro slightly.
Update the $NetBSD$ tags to reflect this and make slight changes to
usb_mem.h so that we're in sync with each other.
revision 1.124
date: 2002/05/26 03:10:02; author: minoura; state: Exp; lines: +3 -3
Clear done_head in the HCCA *before* acknoledging the interrupt.
Driver lost some completed transfers under heavy loads.
date: 2002/05/19 06:24:31; author: augustss; state: Exp;
Update dma memory access API a little.
NetBSD have adopted our way of using the KERNADDR macro. Update
the revision tags to show that we're in sync, and remove the casts
that they did in their adaptation.
remove the need for a contiguous array with pointers to all the sectors.
Try to make failure to malloc(9) memory a non-hang situation.
Eventually this will allow us to test the 64bit cleanness of the disk
I/O patch, but more work is outstanding here and elsewhere.
Sponsored by: DARPA & NAI Labs.
instead of %llx when %j is available).
Changed nearby output formats from %x to %#x so that it is obvious that the
numbers are in hex (vinum mostly uses 0x%x elsewhere).
Didn't fix nearby format printf errors (long lines).
Printing daddr_t's using %d format was always an error, but gcc's
warning about it was ignored for supported 64-bit arches and not printed
for supported 32-bit arches. Hundreds if not thousands thousands of
previously "fixed" daddr_t printings are now broken on 32-bit machines
by casting daddr_t's to longs. daddr_t's should be printed using %jd
format, but this fix uses %lld since %j is not implemented in the
kernel yet.
Fixed some nearby format printf errors (style bugs).
make_dev() to create device nodes for each of the serial port channels
(ttym%d and cuam%d respectively, as borrowed from MAKEDEV). This allows
the rc driver to work in 5.0. I've tested it with only one card, but
will try sticking in a second card tomorrow and see what happens.
the former blocks software interrupts, while the latter blocks
hardware interrupts.
Avoid one place where I'm at splnet across a call to copyout. Leave
one in place to give bde something to complain about :-). Actaully,
I'll fix it in a subsequent commit.
Reviewed by: bde
spl conical hat to: imp
allow recovery from transmission lockups which occur in the middle
of the descriptor list, rather than just at the beginning.
For some unknown reason, Rhine II chips have a tendency to stop
transmitting while under heavy load, possibly due to collisions.
Whether this behavior is due to a hardware bug or a driver glitch
is unknown as of now.
In either case, this change allows the driver to gracefully recover
from such situations.
Special thanks go to The Anarcat <anarcat@anarcat.dyndns.org>, who
bugged me into looking at this and to
Dominic Marks <dominic_marks@btinternet.com>, who performed a great
deal of testing to help characterize this problem.
MFC after: 3 days
previously used "micro-optimization" (count-down loop) into a
pessimization. Now the loops are written in the more natural count-up
form.
Also, while being there, i made the logic in out_fdc() similar to the
logic in in_fdc(). The old implementation was a bit bogus anyway
since it first tested the DIO bit and only afterwards the RQM bit.
However, according to the description of the i82077, the DIO bit is
only guaranteed to be valid once the RQM bit is set. Thus, the old
implementatoin would have had the chance to misbehave on a controller
that is implemented in accordance with the i82077 description (but is
not bug-for-bug compatible).
MFC after: 3 days
-current, since offsetof() is defined a header under /sys so that
system sources don't need to have this wrong include.
This bug was only detected because my version of <stddef.h> has some
spelling fixes (s/field/member/g) and gcc is now sensitive to the spelling
of arg names in macros as required by standards (ISO C90 6.8.3...).
before rev 1.229 (~ 100 ms). According to bde, some (old) broken
hardware could require it. In order to make timing more accurate than
what could be achieved with a loop around DELAY(1), increase loop
timing after the initial ~ 1 ms.
Also, move the declaration of FDSTS_TIMEOUT out from fdreg.h into fd.c
where it actually belongs to.
MFC after: 2 days
in each cycle, with a tunable max cycle count defined in fdreg.h.
This is said to fix the problem on some Compaq hardware (and perhaps
on other machines using the Natsemi PC87317 chip) where the fdc(4)
driver failed to operate at all.
PR: kern/21397
Submitted by: Jung-uk Kim <jkim@niksun.com>
MFC after: 3 days
revision 1.43
date: 2001/04/12 01:39:04; author: thorpej; state: Exp; lines: +2 -2
Switch to USB_USE_SOFTINTR. The callout hack does indeed work
fine for systems without generic soft interrupts, even if it is
a little sub-optimal. Consider it a penalty for ports not
implementing a kernel API.
Addresses kern/11957. The PR has been open for 4 months, and
I have work blocked on the continued existence of splimp() in
the networking code.
The NetBSD patch only switches it on for NetBSD, but I've also
switched it on for FreeBSD in this commit.
be done internally.
Ensure that no one can fsetown() to a dying process/pgrp. We need
to check the process for P_WEXIT to see if it's exiting. Process
groups are already safe because there is no such thing as a pgrp
zombie, therefore the proctree lock completely protects the pgrp
from having sigio structures associated with it after it runs
funsetownlst.
Add sigio lock to witness list under proctree and allproc, but over
proc and pgrp.
Seigo Tanimura helped with this.
usbdi.h (1.60)
(and local changes compatibility changes to ufm.c and urio.c)
date: 2002/02/11 15:11:49; author: augustss;
Give usbd_do_request_flags() an extra argument for the timeout.
This is temporary hack, better and generalized solution probably
should be implemented at lower layer(MII or PCI?).
Tested by: shoko.araki@soliton.co.jp
MFC after: 1 week
call read() to get the next command, and scread() disables the
screensaver. We don't want this behaviour in the sc_saver_keybonly
case.
Submitted by: Olivier Houchard <doginou@ci0.org>
mii_tick() which should only be called once per second.
Our current MII/PHY state-engine is not able to deal with PHY
interrupts as far as I can tell, and most net drivers don't seem
to use the link/status change call-back mechanism. It seems that
MII/PHY was orphaned before it grew up.
revision 1.94
date: 2001/12/30 20:26:59; author: augustss; state: Exp; lines: +5 -2
Make sure we don't have any pending softintrs when entering polling mode.
Thanks to Darrin for finding and fixing this problem when using USB
keyboards in DDB.
is not set in the scsi completion status, or if the residual is clearly
nonsense, then this was a command that suffered the loss of one or more
FC frames in the middle of the exchange.
Set HBA_BOTCH and hope it will get retried. It's the only thing we can do.
MFC after: 1 day
we don't collect any stats in it, we mii_tick() in it! This fix the bug
when autonegotiating fullduplex modes.
Also, pause activity before setting TXCON in epic_miibus_statchg(). Though
i've never seen problmes from not doing that, the documentation says we
need to do it.
MFC after: 1 week
well as is, so - just fetch current status upon MII_TICK.
Also do IFM_INST verification at the top of *_service() then doing it
separately for every case in switch.
acphy: do not read MII_ACPHY_DIAG twice, there is nothing latching.
qsphy: always fetch actual link status from MII_QSPHY_PCTL.
MFC after: 1 week
sent me a replacement patch that fixes the problem. The challenge
buffer was not large enough by a factor of 4 (due to my changing the
size from 128 to 32, but not u_int8_t to u_int32_t).
MFC after: 1 day
Submitted by: skibo@pacbell.net
is limiting it to, not what the device says it can handle.
- cl_status is an integer. cl_lstatus is a pointer.
- Add some debugging code to dump some things the driver knows about
the adapter.
- Tell CAM that the adapter can handle more commands when a command
completes. This fixes the problem were the SIM would freeze once
the driver hit the maximum number of transactions for the device.
- Change the vendor string to COMPAQ.
- Turn of Synchronize Cache for now. It locks the controller up.
Approved by: msmith
Obtained from: Yahoo!
Rename mii_phy_auto_stop() mii_phy_down().
Introduce mii_down(), use it from nge. Do not indirect it to 19 identical
case's in 19 switchstatements like NetBSD did.
breakage when I tried to merge OpenBSD wi_hostap changes into the
tree. Skibo found the problem and submitted these patches. Thanks!
Submitted by: skibo@pacbell.net
ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper
to your high-end RAID controller. The interface to the arrays is still
via the block interface; this merely provides a way to circumvent the
RAID functionality and access the SCSI buses directly. Note that for
somewhat obvious reasons, hard drives are not exposed to the da driver
through this interface, though you can still talk to them via the pass
driver. Be the first on your block to low-level format unsuspecting
drives that are part of an array!
To enable this, add the 'aacp' device to your kernel config.
MFC after: 3 days
timecounter will be used starting at the next second, which is
good enough for sysctl purposes. If better adjustment is needed
the NTP PLL should be used.
ahc_eisa.c:
ahc_pci.c:
Conform to new aic7xxx IRQ API.
Adapt to aic7xxx_freebsd -> aic7xxx_osm changes.
aic7770.c:
Disable card generated interrupt early in our probe for
"extra safety"
Commonize some seeprom code with the PCI side of the driver.
aic7xxx.c:
Correctly initialize a few scratch ram locations during
a sequencer restart. This avoids spurious sequencer ram
parity errors in some configurations.
Include the softc in ahc_update_residual calls. We need it
for some diagnostics in this code path.
Flag a data overrun on an auto-request sense failure as a
CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR.
Force a renegotiation after noticing a parity error. This
covers targets that lose our negotiation settings but don't
bother to give us a unit attention condition. This can happen
if a target fails during a reselection of us during a cable
pull.
Convert some code to using constants.
Fix some typos.
Correct target mode message loop handling. ahc_clear_msg_state
was not clearing the "need to go to message out phase" bit once
our loop was over.
Simplify some abort handling code.
Include tag information in target mode immediate notify events.
When shutting down EISA controllers, don't EISA BIOS settings in
the high portions of scratch ram. This fixes warm boot issues on
some systems.
Save a bit of space by only allocating the SCBs that we can use.
Avoid some code paths in ahc_abort_scbs() if we are currently
acting as a target.
Correctly cleanup stranded SCBs in the card's SCB array. These
are SCBs who's mapping has already been torn down by code that
aborted the SCB by seeing it in another list first.
Add a comment about some potential bus reset issues for target
mode on Twin (EISA only) controllers.
aic7xxx.h:
Cleanup the hardware scb definitions a bit.
Allocate a ful 256 byte scb mapping index. This simplifies
the lookup code since the table covers all possible (and potentially
bogus) values.
Make AHC_DEBUG work again.
aic7xxx.reg:
Updates to hardware SCB definition.
New definitions for target mode fixes.
aic7xxx.seq:
In target mode, initialize SAVED_LUN just after we receive
the identify message. It may be required in the error recovery
path when a normal cdb packet (includes lun) is not sent up to
the host for processing.
Respond to irregular messages during a selection in target mode.
Defer looking for space for a cdb packet until we are about to
enter command phase. We want to be able to handle irregular messages
even if we would otherwise return QUEUE_FULL or BUSY.
Add support for sending Ignore Wide Residue messages as a target.
In the disable disconnect case in target mode, set our transfer
rate correctly once data are availble.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Add the ability to write and erase the seeprom.
aic7xxx_inline.h:
Correct Big Endian handling of large cdb sizes (> 12 bytes).
Adaptec to changes in the calc_residual API.
Correct a target mode bug where we always attempted to service
the input queue even if no progress could be made due to lack
of ATIOs.
aic7xxx_osm.c:
Adaptec to new IRQ mapping API. The new API allows the core
to only enable our IRQ mapping once it is safe (sufficient
initialization) to do so.
Slap bootverbose protection around some diagnostics.
Only attempt DT phases if we are wide.
aic7xxx_osm.h:
Enable big endian support.
Adjust for IRQ API change.
aic7xxx_pci.c:
Be more careful about relying on subvendor 9005 information.
We now only trust it for HBAs. This should allow the driver
to attach to some MBs where the subvendor/device information
does not follow the Adaptec spec.
Only enable interrupts on the card once we are fully setup.
Disable external SCB ram usage on the aic7895. I have not
been able to make it 100% reliable.
Adjust to seeprom routines being properly prefixed with "ahc".
Fix a few bugs in the external SCB ram probing routine. We
need to clear any parity errors we've triggered during the
probe to avoid future, fatal, interrupts.
If we detect an invalid cable combination, pretent there are
no cable at all. This will enable all of the terminators
which is probably the safest configuration we can "guess".
MFC after: 4 days
-stable machine via the old-school methods):
Use __FreeBSD_version in preference to __FreeBSD__ >= N where possible.
Define a single variable mythread which is set to curproc or curthread
depending on the OS version (with a comment saying it is a white lie on
4.x since it really is a proc).
NB: __FreeBSD__ is the OS level of the host machine, not the target,
and should never be used, if possible, as __FreeBSD__ >= N.
Rev 1.56 of if_dc.c removed calls to mii_pollstat() from the dc_tick()
routine. dc_tick() is called regularly to detect link up and link down
status, especially when autonegotiating.
The expectation was that mii_tick() (which is still called from dc_tick())
would update status information automatically in all cases where it would
be sensible to do so.
Unfortunately, with authentic 21143 chips this is not the case, and
the driver never successfully autonegotiates. This is because (despite
what it says in the 21143 manual) the chip always claims that link is not
present while the autonegotiation enable bit is set. Autonegotation takes
place and succeeds, but the driver tests the link bits before it switches
off the autonegotiation enable bit, and success is not recognised.
The simplest solution is to call dcphy_status() more often for MII_TICK
calls by dropping out of the switch statement instead of exiting when
we are autonegotiating and link appears to not be present. When
autonegotiation succeeds, dcphy_status() will note the speed and fdx/hdx
state and turn off the autonegotiation enable bit. The next call to
dcphy_status() will notice that link is present, and the dc driver code
will be notified.
Macronix chips also use this code, but implement link detection as
described in the manual, and hence don't need this patch. However, tests
on a Macronix 98715AEC-C show that it does not adversely affect them.
This could be done better but is the minimal effective change, and most
closely mimics what was happening prior to rev 1.56 of if_dc.c. (Actually
I also deleted a small amount of unnecessary code while I was in the area.)
Reviewed by: wpaul
loop is inversly proportional to hz.
This makes things more sane for configurations with hz != 100.
Cosmetic: Make the loops look similar to the loops in digi.c
loop is inversly proportional to hz.
This makes things more sane for configurations with hz > 100.
Submitted by: Peter Jeremy <peter.jeremy@alcatel.com.au>
environment needed at boot time to a dynamic subsystem when VM is
up. The dynamic kernel environment is protected by an sx lock.
This adds some new functions to manipulate the kernel environment :
freeenv(), setenv(), unsetenv() and testenv(). freeenv() has to be
called after every getenv() when you have finished using the string.
testenv() only tests if an environment variable is present, and
doesn't require a freeenv() call. setenv() and unsetenv() are self
explanatory.
The kenv(2) syscall exports these new functionalities to userland,
mainly for kenv(1).
Reviewed by: peter
- Add stubs for EISA and SBUS cards.
(VME, FutureBUS, and TurboChannel stubs not provided.)
- Add infrastructure to build driver and bus front-end modules.
lun address modifier of sorts. Only an HP XP-512 seems to have cared.
Fix a few misplaced pointers for the new fabric goop, which has been
demonstrated to work on newer Brocades and McData switches now.
Put in commented out code which would run GFF_ID if the QLogic f/w
allowed it.
Don't whine about not being able to find a handle for a command if it
was a command aborted (by us).
o move timeout from wihap_info to wihap_sta_info
o sprinkle spls into the code (need to use proper -current locking)
o better use of le16toh and htole16
o fix a few leaks m_freem(m)
o minor knf
o minor de-knf to match OpenBSD
o de__P
- Add a device_method_t array, fore_methods.
- Add a fore_ident_table that contains the various FORE Systems PCA-200
series devices.
- Rewrite of the fore_probe routine (formerly known as fore_pci_probe).
- Minor changes... mostly WIP stuff to get this updated... still much to
be done.
the per-channel bus_addr_t offset. Also, cast the offset to (long long)
and use %#llx instead of %#x to fix printf warnings on architectures where
sizeof(bus_addr_t) != sizeof(int).
es137x.c: In function `es1371_rdcd':
es137x.c:598: warning: `x' might be used uninitialized in this function
PR: kern/35408
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
that declares itself to be a disk, which may be the wrong thing to do in
the long term but it works well enough to attach to emulated disks in the
PowerPC simulator in gdb now that they have the proper device_type
property.
The extra microphone channel capability is part of the "normal" ac97
capabilities and not an extended ac97 capability. Now recording on
codecs without a seperate mic channel works.
MFC after: 1 week
FIFO or the in-RAM descriptors it will switch to RX_IDLE from where it
is not restarted.
We used to deal with RX_IDLE by doing a total reinit but this lost
our link and caused a potential 30sec autonegotiation against
switches. This was changed to a less heavyhanded approach, but this
failed to restart the receiver it it were in the RX_IDLE state.
This change adds the RX_IDLE and the RX_FIFO_OFLOW conditions as
triggers for interrupts and receive side processing, and restarts
the receiver when it is RX_IDLE.
Remove the #ifdef notyet'ed nge_rxeoc() function.
Sponsored by: Cybercity Internet, Denmark.
MFC after: 7 days
(apparently by markus@, at least committed by him). This has the
advantage of not using the bad IV's from Fluhrer/Mantin/Shamir as well
as bringing the drivers a little closer together.
Also use a few constants in place of magic numbers in one place.
Obtained from: OpenBSD 1.25, 1.28, 1.36, 1.38, 1.42
time we tell CAM to rescan the bus. Together with the previous patch
this should avoid the problem where the devices would wedge because they
got spoken to over two different pipes.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
wrote. This code was for 4.5-release, so I've ported it to -current
and made a few minor tweaks. The biggest non-style tweak was to not
make access point the default.
More changes will be needed to get this actually working, but I wanted
to get a relatively pure baseline. This doesn't seem to break what
works now.
attachment after boot in some cases where the device gets confused if
spoken to over two different pipes simultaneously (resulting in TIMEOUT
errors on requesting INQUIRY data).
This solution is far from perfect, as after umass_attach has returned
the USB stack fetches the string descriptors in order for creating the
event that is sent to userland. It just makes the chances of collisions
less likely.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
submitter, this permits Russian (and probably other locales') characters
to be entered via watch(8).
PR: 35636
Submitted by: Gleb Smirnoff <glebius@rinet.ru>
the card for command completion.
digi_delay() uses either tsleep() or DELAY() depending on the value of
``cold''.
Pointed in the right direction by: jhb
Add the card name to the error message for the first initialisation
failure, giving us more info about what was actually discovered.
This code has been tested by Robert Suetterlin <robert@mpe.mpg.de>
to work on a PCI Xem card.
mod_depend * (which may be NULL). The only consumer of this
function at the moment is digi_loadmoduledata(), and that passes
a NULL mod_depend *.
In linker_reference_module(), check to see if we've already got
the required module loaded. If we have, bump the reference count
and return that, otherwise continue the module search as normal.
newer ultras and probably other sun machines. This is a pretty decent
chip with 32 byte read and write fifos and support for many higher baud
rates. It supports hdlc and sdlc as well as asynchronoue serial, but the
goal here is just decent serial console support for the sparc64 port, so
these modes are not expected to be supported. So far this only has support
for the low level routines used by kernel printf and thus ddb over serial,
a character device which can be used for login consoles has not yet been
written.
doesn't support NWAY, the RealTek PHY (both the integrated ones on 8139
chips and the RTL8201L 10/100 PHY) will not report the link speed via
the ANLPAR or BMSR registers. For the 8201L, we need to look in magic
vendor-specific PHY register 0x19. For the 8139 MAC+PHY combo, we have
to be able to test the RL_MEDIASTAT register.
The changes to rlphy.c are based largely on the patch from PR 30836,
however I tried to eliminate some magic numbers by creating an entry
for the 8201 PHY in miidevs.
Also updated if_rl.c to allow the rlphy driver to read the RL_MEDIASTAT
register via the rl_miibus_readreg() routine.
revision 1.153
date: 2002/02/11 11:40:33; author: augustss; state: Exp; lines: +67 -26
Switch to the same abort mechanism as in [eo]hci; it should be more
robust.
revision 1.151
date: 2002/01/27 23:00:34; author: augustss; state: Exp; lines: +3 -3
Use M_WAITOK instead of M_NOWAIT when allocating extra descriptors.
Spotted by OpenBSD.
date: 2000/12/29 01:47:49; author: augustss;
Supply our own report descriptor (from Nick Hibma) for the Wacom Graphire.
The descriptor it reports is broken.
XXX Not tested, because I don't have the device.
date: 2001/08/15 00:06:49; author: augustss; state: Exp; lines: +3 -1
If there was a vendor+product locator match return a higher match value.
Rationale, if you have a device (e.g., a mouse) with a more specific
driver but want to recognize it with the more generic driver you can
do that by supplying vendor and product locators for the generic one.
revision 1.101
date: 2001/02/20 15:20:32; author: minoura;
Re-initialize some registers after resuming from suspend.
Some APM BIOSes do not restore them.
Reviewd by augustss.
revision 1.97
date: 2000/12/31 14:29:54; author: augustss; state: Exp; lines: +17 -3
Make the controller survive suspend/resume. Thanks to Steve Woodford
<steve@mctavish.co.uk> for testing.
revision 1.95
date: 2000/12/13 03:09:06; author: augustss; state: Exp; lines: +19 -3
Make the ohci driver not hang suspend/resume. It still doesn't resume
correctly. From itohy@netbsd.org (ITOH Yasufumi) PR kern/11714.
revision 1.58
date: 2001/11/20 23:53:26; author: augustss; state: Exp; lines: +61 -33
Create a special kernel thread to run the usb short lived tasks (instead
of using the device discovery threads).
revision 1.65
date: 2002/01/03 22:20:45; author: augustss; state: Exp; lines: +9 -2
Add a DIAGNOSTIC check. From FreeBSD.
(Just wrap these changes, that we already had, with a #ifdef DIAGNOSTIC).
revision 1.62
date: 2002/01/02 20:55:58; author: augustss; state: Exp; lines: +11 -10
Some more usb_proc_ptr changes.
Also some minor stylistic changes.
revision 1.63
date: 2002/01/02 20:58:12; author: augustss; state: Exp; lines: +4 -4
Fix typo in last commit.
revision 1.64
date: 2002/01/02 22:44:44; author: augustss; state: Exp; lines: +7 -4
Add a comment.
The usb_proc_ptr changes were introduced in 1.62 and backed out in 1.64.
revision 1.61
date: 2001/12/31 15:55:51; author: augustss; state: Exp; lines: +3 -5
Delay bus enumeration a little in case the controller is a companion
controller. This way the main controller can gain ownership of the port
before enumeration starts.
date: 2001/11/20 23:53:26; author: augustss; state: Exp; lines: +61 -33
Create a special kernel thread to run the usb short lived tasks (instead
of using the device discovery threads).
The change to usb_port.h is a little hack whilst I address an issue
with NetBSD.
revision 1.68
date: 2001/12/24 21:36:16; author: augustss; state: Exp; lines: +2 -1
Add some more DIAGNOSTIC tests.
Make usb_match_device() match on USB_PRODUCT_ANY.
if_cuereg.h (1.5), if_kue.c (1.11), if_kuereg.h (1.5)
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
We don't have ratecheck() in our kernel yet, so I've hardcoded
usb_ratecheck() to return true always.
usbdi.c (1.86), usbdivar.h (1.66)
[Some partial, because most of this was merged in a while ago]
date: 2001/11/20 13:48:03; author: augustss;
Keep track of device speed for USB 2.0.
revision 1.106
date: 2001/11/09 15:01:57; author: augustss; state: Exp; lines: +73 -57
Fix a bug in xfer abort processing when the HC executes ahead of what
the driver aborts.
Don't block RHSC interrupts.
revision 1.103
date: 2001/09/11 07:00:19; author: augustss; state: Exp; lines: +4 -1
Don't go top mode OPERATIONAL (before reset) on startup even
if BIOS claims to have initialized the controller.
hw.syscons.saver.keybonly: used to specify that only input is to
interrupt the screensaver. This allows one to run a chatty console
app but still have the screen blank out until a key is pressed.
There should probably also be an ioctl for this, we'll do that later.
hw.syscons.saver.blanktime: exports the screensaver timeout via sysctl.
Submitted by: Olivier Houchard <doginou@cognet.ci0.org>
interface that is compatible with the LUCENT or HERMES firmware.
Instead, it is like the various No Wires Necessary products that were
produced a while ago and then sold to intersil. It will require a
different driver altogether. Remove it from the list of supported
cards.
The 3CRWE777A apperas to be a re-badged SMC 2602W card, so the driver
appears to support it. Add it to the list.
Thanks to Todd Miller for loaning me the card during tonight's FRUUG
meeting for testing against CU's wireless infrastructure.
Grumble. I've seen better documented architectures out of Redmond.
Redo fabric evaluation to not use GET ALL NEXT (GA_NXT). Switches seem
to be trying to wriggle out of supporting this well. Instead, use
GID_FT to get a list of Port IDs and then use GPN_ID/GNN_ID to find the
port and node wwn. This should make working on fabrics a bit cleaner and
more stable.
This also caused some cleanup of SNS subcommand canonicalization so that
we can actually check for FS_ACC and FS_RJT, and if we get an FS_RJT,
print out the reason and explanation codes.
We'll keep the old GA_NXT method around if people want to uncomment a
controlling definition in ispvar.h.
This also had us clean up ISPASYNC_FABRICDEV to use a local lportdb argument
and to have the caller explicitly say that a device is at the end of the
fabric list.
MFC after: 1 week
time-of-day clocks, ported from NetBSD. The front-ends are expected
to be at least partly machine-dependent; the sparc64 EBus and SBus
ones will be commited to MD directories for now (in a subsequent commit).
wi.c 1.64: Table driven IDs (ichiro)
1.59: Don't use magic numbers (ichiro)
Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent
cards (and submit those changes back to ichiro-san)
Obtained from: NetBSD
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
o OpenBSD's wiconfig tells me that a value of '2' is for sony wireless
cards, 1 is for lucent (which we already knew) and '5' is for embedded
lucent cards.
o Move some RID definitions to if_wavelan_ieee.h and use NetBSD names
more often.
# more work is still needed in this area.
interrupts. This is a bit harder than it needs to be because there's
more than one way to generate link attentions, at least one of which
does not work on the BCM5700, but does on the 5701.
For the 5701, we can safely use the 'link changed' bit in the status
block, and we enable link change attentions in the mac event register.
For the 5700, we have to use MII interrupts, which require checking
the MAC status register rather than the status block. This requires
doing an extra register access on each interrupt which I'd prefer to
avoid, but them's the breaks. Testing with both a 3c996-T and 3c996B-T
shows that we do in fact detect the link going up and down properly
on cable insertions/disconnections.
Also, avoid twiddling the autopoll enable bit in the MI mode register
when doing a PHY read. I think this coupled with the other changes
will stop the interrupt storms Paul Saab has been harassing me about.
Manually setting the link to 100baseTX full duplex seems to work ok
for me. (I'm typing over the 3c996B-T right now.)
Lastly, teach the driver how to recognize a 3c996B-SX by checking
the hardware config word in the EEPROM in order to detect the media.
We attach 5701 fiber cards correctly now, but I haven't verified that
they send/receive packets yet since I don't have a second fiber
interface at home. (I know that fiber 5700 cards work, so I'm
keeping my fingers crossed.)
This driver was written by Myson and is made available
by their courtesy.
The 5.x version is not fully tested (I will be testing) but
the 4.x version has been tested by many.
I will commit it soon.
Myson have their own chip design based on the DEC 214xx family but
with several differences. Myson sells this chip to several
EOMs in teh Chinese area so there may be many noname brand cards
that respond to this driver. Myson will be supplying a list
of some of these.
1) Properly detect the Symbol based cards (The 3Com Airconnect and their
ilk) and only reset them *ONCE* ever. This appears to make them work,
but more testing is needed. The tests that would wedge up my machine
completely now appear to work, but I have not real access points
handy.
2) Report both the Station firmware and the Primary firmware on Prism
based cards. On Lucent based cards, only report the station firmware
since that's all it supports. On symbol cards, report the symbol
specific firmware name as its station firmware.
3) Better Prism 2.5 and 3 family names. We really need to go table
driven for this.
4) Workaround for bugs in Intersil's firmware is only needed for at most
0.8.2 and earlier, since 0.8.3 and later appear to work.
Obtained from: NetBSD
stuff was right, but the busdma stuff was massively not right.
Didn't really test on ia64 or i386- don't have the former h/w and my
FreeBSD-current disk is unwell right now. Hope that this is okay.
MFC after: 1 week
"raw partition" of any kind since the floppy driver doesn't support
UFS-style partitions at all.
Reported by: "Crist J. Clark" <crist.clark@attbi.com>
Reviewed by: bde
MFC after: 3 days
date: 2001/08/15 00:04:59; author: augustss;
Add a little infrastructure so that individual drivers can easily check
if thee was a vendor+product locator match.
DIOCGMEDIASIZE instead.
The partition type check has been XXX'ed out since we cannot expect
that a BSD disklabel with a type field be available on all platforms.
revision 1.50
date: 2001/04/12 01:18:24; author: thorpej; state: Exp; lines: +6 -2
Only if __HAVE_GENERIC_SOFT_INTERRUPTS is then splusb == splsoftnet
(because we register the interrupt with IPL_SOFTNET). However, if
we're using a callout, then splusb == splsoftclock (because the
callouts happen from the softclock interrupt).
Note that splsoftnet blocks softclock interrupts, but this is
meant to better describe what's going on.
date: 2001/01/21 19:00:06; author: augustss;
Change the operation of the USB event thread. Before it only
performed USB device discovery, now it can also perform (short)
tasks for device drivers that need a process context, but don't
have one. This is not pretty, but better than using busy-wait
in an interrupt context.
o 3Com 3crwe62092a
o Addtron awp100
o No Wires Necessary WLAN 550 and 1148
o Proxim RANGELANDS 8340
and reorder linksys to be in proper sort order.
Obtained from: OpenBSD (mostly)
revision 1.138
date: 2001/10/02 17:59:38; author: pooka; state: Exp; lines: +6 -6
move DIAGNOSTIC-printf up one block to make it reachable
noted by Christophe Kalt in private email
(1.39), usbdi.c (1.79), usbdi.h (1.47), usbdivar.h (1.62)
date: 2001/01/21 02:39:52; author: augustss;
Add code to use soft interrupt to handle USB interrupt processing.
Don't enable the code since it doesn't work with the kludgy Ethernet
drivers.
general cleanup of the API. The entire API now consists of two functions
similar to the pre-KSE API. The suser() function takes a thread pointer
as its only argument. The td_ucred member of this thread must be valid
so the only valid thread pointers are curthread and a few kernel threads
such as thread0. The suser_cred() function takes a pointer to a struct
ucred as its first argument and an integer flag as its second argument.
The flag is currently only used for the PRISON_ROOT flag.
Discussed on: smp@
revision 1.58
date: 2000/06/24 04:12:53; author: thorpej; state: Exp; lines: +5 -2
Kill SPLUSBCHECK -- it's not portable, and quite annoying on some
platforms which otherwise function just fine.
revision 1.127
date: 2000/11/22 05:50:59; author: soren; state: Exp; lines: +5 -5
In uhci_intr(), only warn about power state confusion if the
interrupt was actually for us.
date: 2000/08/08 19:51:46; author: tv; state: Exp; lines: +24 -13
%b -> bitmask_snprintf()
Because this code is shared, add a macro for bitmask_snprintf()
that should expand to the equivalent snprintf() on non-NetBSD
systems. This is only used in ?HCI_DEBUG cases anyway.
revision 1.81
date: 2000/10/24 15:01:26; author: augustss; lines: +36 -10
Add a hack to try and figure out if the TI UTUSB41 hub is bus
powered despite claiming to be self powered (it's important to
know so that the power budget can be met).
Part of this got merged in a previous commit, but not all.
revision 1.72
date: 2000/04/14 14:13:56; author: augustss; state: Exp; lines: +34 -27
Make attach of ugen work as it should so product&vendor locators
can be used.
usb.c 1.40:
revision 1.40
date: 2000/03/14 23:13:12; author: augustss; state: Exp; lines: +4 -1
Make sure the USB event thread discovers all devices first time
it call usb_discover(). It should now be possible to have the
root NFS mounted over a USB Ethernet Adapter.
----------------------------
revision 1.73
date: 2000/05/31 16:14:42; author: augustss; state: Exp; lines: +19 -6
Be more careful when setting the alternate interface so we don't
end up with nothing set at all if it fails.
----------------------------
----------------------------
revision 1.117
date: 2000/05/30 09:26:06; author: augustss; lines: +7 -1
As a safety, check that the controller is not suspended when we get
an interrupt.
----------------------------
ohci.c (1.85), ohcireg.h (1.17):
----------------------------
date: 2000/04/01 09:27:35; author: augustss;
Add a delay before reading the number of ports from the controller to
avoid getting 0 from it.
----------------------------
ohci.c (1.83), ohcireg.h (1.16), ohcivar.h (1.21)
===================================================================
date: 2000/03/29 01:46:26; author: augustss;
A first stab at support for isochronous transfers.
===================================================================
Caveats:
The new savecore program is not complete in the sense that it emulates
enough of the old savecores features to do the job, but implements none
of the options yet.
I would appreciate if a userland hacker could help me out getting savecore
to do what we want it to do from a users point of view, compression,
email-notification, space reservation etc etc. (send me email if
you are interested).
Currently, savecore will scan all devices marked as "swap" or "dump" in
/etc/fstab _or_ any devices specified on the command-line.
All architectures but i386 lack an implementation of dumpsys(), but
looking at the i386 version it should be trivial for anybody familiar
with the platform(s) to provide this function.
Documentation is quite sparse at this time, more to come.
Details:
ATA and SCSI drivers should work as the dump formatting code has been
removed. The IDA, TWE and AAC have not yet been converted.
Dumpon now opens the device and uses ioctl(DIOCGKERNELDUMP) to set
the device as dumpdev. To implement the "off" argument, /dev/null
is used as the device.
Savecore will fail if handed any options since they are not (yet)
implemented. All devices marked "dump" or "swap" in /etc/fstab
will be scanned and dumps found will be saved to diskfiles
named from the MD5 hash of the header record. The header record
is dumped in readable format in the .info file. The kernel
is not saved. Only complete dumps will be saved.
All maintainer rights for this code are disclaimed: feel free to
improve and extend.
Sponsored by: DARPA, NAI Labs
have ripped all the i386 specific formatting code from their
dump routines. Due to the potential for trashing disks, I did
not want to do this "blind".
(65536 * 32 - 1), but MAKEDEV only supports up to (32 * 32 -1). Device
names use the unit number in base 32 for all "digits".
This required fixing an old bug in MAKEDEV:ttyminor(). Its arg was the
global $unit instead of $1.
Reminded by: Valentin K. Ponomarenko <valka@krog.ukrtel.net>
MFC-after: 1 week
measured accurately for periodic interrupts provided the interrupts
don't need to be serviced very quickly to keep their period almost
constant. sio output interrupts have this property (interrupt service
can be delayed for up to 1 character time without the period changing).
This is non-optional and undocumented so that it can be added and
removed easily. It has no significant effect unless it is enabled by
hacking on a variable using a debugger. Hardclock and statclock interrupts
would work even better for this, at least on i386's, provided their
interrupt handlers are fast (as they are in -current but not in -stable
or in my version of -current).
allows us to properly parse cards with attribute memory based CIS that
before wouldn't parse correctly, sometimes with a panic. This allows
me to get my 3C562 modem/ethernet card to fail to attach due to
problems in the ep and sio drivers rather than due to problems in the
CIS parsing code :-).
We weren't setting the address to jump to for the function entries.
This caused us to only work when the addional entries were after the
first ones. On the 3C562/3C563 card this was not the case.
We were also mapping Attribute memory when common memory was asked for
in the target of the LONGLINK_{A,C} or LONGLINK_MFC.
My IBM Home And Away Modem/LAN card still fails for reasons unknown.
This completes the ATA RAID support, since all functions to manipulate
the RAID are accessible from FreeBSD, the BIOS on the ATA RAID cards
are only nessesary for booting.
I decided to allow for creation of ATA RAID's on any ATA controller, but
please keep in mind the restrictions on that. Due to the BIOS not
knowing what to do you can only boot from a RAID1 or the first disk
in a SPAN, if its not located on a "real" ATA RAID controller like
the Promise or Highpoint controllers.
Sponsored by: Advanis
The conclusion is that this method really can tell the perfect from the
less than perfect ACPI counters.
It is in fact probably a bit more discriminative than that, but we
will rather condemn some otherwise perfect counters to the slightly
slower "-safe" version, than certify a counter as perfect which
will let us down later.
Many thanks to all the people who sent email reports!
by the hardware are still marked as owned. Handle this by installing a
timeout handler to collect this descriptor to avoid having received
packets remain unhandled until the next one arrives.
- remove some useless code from the status change handler that was intended
to enable the the MII drivers for external phys; this is already done
during interface initialization, and the deleted code made some
assumptions about phy addresses that do not seem to hold true on newer
cards. This should get at least one of the two hmes of newer Netra t1
machines working.
- correct the interrupt resource allocation
- bump the number of RX descriptors, lower values cause promblems on some
machines
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
3c996B-T, with the 5701 rev B5 ASIC). One thing that confuses me
still is that the 'link state change' bit in the status block seems
to change state an awful lot. I have a workaround for this in place
now, but it needs more investigation. For the moment though, this
is enough to get the driver to work with this card.
soon because it's just getting harder and harder to find switches
that correctly implement the GET ALL NEXT subcommands for the SNS
protocol.
Latch up result out pointer and set a busy flag when we're looking
at the response queue. This allows for a cleaner way to make sure
we don't get multiple CPUs trying to read the same response queue
entries.
Change how isp_handle_other_response returns values (clarity).
Make PORT UNAVAILABLE the same as PORT LOGOUT (force a LIP).
Do some formatting changes.
MFC after: 0 days
keep gcc-3.1+ happy:
ata-all.c:410: warning: deprecated use of label at end of compound statement
ata-all.c:587: warning: deprecated use of label at end of compound statement
ata-raid.c:99: warning: deprecated use of label at end of compound statement
ata-raid.c:151: warning: deprecated use of label at end of compound statement
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
"Fixed" format printf error in previous commit. This file is not
formatted in KNF. Partially restore bug for bug compatibility: indent
the printf args too much, but don't format them for 160-column terminals.
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
o Add exerpimental support for identifying lucent cards. All of mine
come back with ID of 1, but NetBSD committed code for 5. So accept
both.
o rename wi_prism2_ver to wi_firmware_ver so that we could, if necessary,
do special things for lucent cards too.
o Bring in a small part of the changes from airtools: The wi_cmd function
now takes two additional arguments. I didn't bring in their ioctls yet.
o eliminate the use of LE16TOH, and remove its define.
o Print the firmware as if there were 100 versions instead of 10. This means
that 6.1 and 6.10 aren't confusing to people. We now print 6.01 in the
former case.
# A good junior hacker project would be to merge the NetBSD, FreeBSD, and
# OpenBSD drivers into one source base.
ohcivar.h (1.22), uhcivar.h (1.29):
============================================================
date: 2000/04/25 09:20:55; author: augustss;
Move the size of the mapped bus_space region into the bus
independent softc.
============================================================
ohci.c (1.88), uhci.c (1.112):
============================================================
date: 2000/04/25 14:28:13; author: augustss;
Insert (very conservative!) bus_space_barrier() calls at
all register accesses.
The bus_space(9) man page says you've gotta have them...
============================================================
usbdi.c (1.61):
===================================================================
revision 1.61
date: 2000/01/31 20:13:07; author: augustss; lines: +20 -4
Change the way the HC done method is invoked a little.
===================================================================
usbdi.c (1.65):
===================================================================
revision 1.65
date: 2000/03/08 15:34:10; author: augustss; lines: +4 -2
Get the status right when a polled transfer times out.
===================================================================
ohci.c (1.79), uhci.c (1.89), uhcivar.h (1.24), usb_port.h (1.22),
usbdivar.h (1.48):
===================================================================
date: 2000/03/23 07:01:46; author: thorpej;
New callout mechanism with two major improvements over the old
timeout()/untimeout() API:
- Clients supply callout handle storage, thus eliminating problems of
resource allocation.
- Insertion and removal of callouts is constant time, important as
this facility is used quite a lot in the kernel.
The old timeout()/untimeout() API has been removed from the kernel.
===================================================================
uhci.c (1.80), usbdi.c (1.66):
===================================================================
date: 2000/03/23 18:59:10; author: thorpej;
Shake out some bugs from the callout changes.
===================================================================
ohci.c (1.80), uhci.c (1.91), uhcivar.h (1.25), usb_port.h (1.23),
usbdi.c (1.67), usbdivar.h (1.49):
===================================================================
date: 2000/03/24 22:03:30; author: augustss;
Some cleanup and renaming of the callouts used in USB drivers.
===================================================================
uhci.c (1.92), uhcivar.h (1.26):
===================================================================
date: 2000/03/24 22:57:58; author: augustss;
Two major changes:
Make each xfer have its own intr_info. This is necessary if we want
to queue multiple xfers on an endpoint. This should get rid of the
(mostly harmless) DIAGNOSTICs about intr_infos (not) being done.
Change (again!) how xfers are aborted. Aborting a TD is a nightmare
on the braindead UHCI controller. (Unless you stop the HC, thereby
losing isoc traffic.) Hopefully I got it right this time.
===================================================================
usbdivar.h (1.50):
===================================================================
revision 1.50
date: 2000/03/25 00:10:19; author: augustss; lines: +4 -2
GC an unsued field and add some DIAGNOSTIC in xfer.
===================================================================
ums.c: Use the callout functions instead of the timeout ones.
uhci.c (1.93):
===================================================================
revision 1.93
date: 2000/03/25 00:11:21; author: augustss;
lines: +26 -1
Add more DIAGNOSTIC when aborting isoc.
===================================================================
uhci.c (1.94), usbdivar.h (1.51):
===================================================================
date: 2000/03/25 07:13:05; author: augustss;
More DIAGNOSTIC.
Initialize a callout handle I forgot.
===================================================================
uhci.c (1.95):
===================================================================
revision 1.95
date: 2000/03/25 07:23:12; author: augustss;
Exp; lines: +24 -7
Improve uhci_dump_ii().
===================================================================
ohci.c (1.81), uhci.c (1.96), uhcivar.h (1.27), usb_subr.c (1.68),
usbdi.c (1.68), usbdivar.h (1.52):
===================================================================
date: 2000/03/25 18:02:33; author: augustss;
Rename and move around callout handles to make it more sane.
Add some DIAGNOSTIC.
Fix buglet in isoc abort on UHCI.
===================================================================
uhci.c (1.98):
===================================================================
revision 1.98
date: 2000/03/27 07:39:48; author: augustss; lines: +12 -4
Make it compile without DIAGNOSTIC.
===================================================================
uhci.c (1.99):
===================================================================
revision 1.99
date: 2000/03/27 08:01:09; author: augustss; lines: +1 -5
Remove some debug nonsense.
===================================================================
uhci.c (1.100):
===================================================================
revision 1.100
date: 2000/03/27 09:41:36; author: augustss; lines: +13 -3
Don't mess with QH in bulk abort for the moment.
===================================================================
uhci.c (1.102):
===================================================================
revision 1.102
date: 2000/03/27 22:42:57; author: augustss; lines: +66 -26
Be a little more careful when aborting.
Preallocate some TDs for large buffers.
===================================================================
uhci.c (1.103):
===================================================================
date: 2000/03/28 09:47:10; author: augustss; lines: +11 -1
Another patch for xfer abort...
XXX The current xfer queueing and aborting semantics should really
XXX be changed. It cannot be implemented in a sane way on UHCI.
XXX One day when I have lots of time I'll redesign it...
===================================================================
uhci.c (1.104): Correct a debug message.
uhci.c (1.105): Be more defensive in a DIAGNOSTIC test.
uhci.c (1.106):
===================================================================
revision 1.106
date: 2000/03/29 01:49:13; author: augustss; lines: +14 -309
*SIGH* Revert back to the old method of aborting xfers.
I had tested the new stuff for two months now, but as soon as I commited
it the problems started to appear. Murphy, no doubt...
===================================================================
usb_subr.c (1.70), usbdi.c (1.71), usbdivar.h (1.53):
===================================================================
revision 1.70
date: 2000/03/29 01:45:20; author: augustss; lines: +2 -1
Do not accept new xfers for queuing while a pipe is aborting.
===================================================================
to put the device into 8 bit mode a second time. This appears to have
no ill effects on other devices, and appears to be necessary for the
xircom modem.
Submitted by: gwk@sgi.com, many others that found his patch in the archives.
the bio and buffer structures to have daddr64_t bio_pblkno,
b_blkno, and b_lblkno fields which allows access to disks
larger than a Terabyte in size. This change also requires
that the VOP_BMAP vnode operation accept and return daddr64_t
blocks. This delta should not affect system operation in
any way. It merely sets up the necessary interfaces to allow
the development of disk drivers that work with these larger
disk block addresses. It also allows for the development of
UFS2 which will use 64-bit block addresses.
Problem:
selwakeup required calling pfind which would cause lock order
reversals with the allproc_lock and the per-process filedesc lock.
Solution:
Instead of recording the pid of the select()'ing process into the
selinfo structure, actually record a pointer to the thread. To
avoid dereferencing a bad address all the selinfo structures that
are in use by a thread are kept in a list hung off the thread
(protected by sellock). When a selwakeup occurs the selinfo is
removed from that threads list, it is also removed on the way out
of select or poll where the thread will traverse its list removing
all the selinfos from its own list.
Problem:
Previously the PROC_LOCK was used to provide the mutual exclusion
needed to ensure proper locking, this couldn't work because there
was a single condvar used for select and poll and condvars can
only be used with a single mutex.
Solution:
Introduce a global mutex 'sellock' which is used to provide mutual
exclusion when recording events to wait on as well as performing
notification when an event occurs.
Interesting note:
schedlock is required to manipulate the per-thread TDF_SELECT
flag, however if given its own field it would not need schedlock,
also because TDF_SELECT is only manipulated under sellock one
doesn't actually use schedlock for syncronization, only to protect
against corruption.
Proc locks are no longer used in select/poll.
Portions contributed by: davidc
-#if defined(__FreeBSD__) && __FreeBSD_version__ >= 500023
+#if defined(__FreeBSD__) && __FreeBSD_version >= 500023
is a genuine bug -- __FreeBSD_version__ does not exist.
The other one:
-#if (__FreeBSD__ < 5)
+#if (__FreeBSD_version < 500000)
pops out when you cross-compile the code:
__FreeBSD__ is a compiler predefine,
__FreeBSD_version is defined in <sys/param.h> .
Given that in this case (and all others in sys/dev/usb and sys/i4b)
the goal is to adapt to a different kernel interface, and not to
a compiler feature, I believe the correct form is the second one
(in the best case the two are synonyms so the change does not break
anything anyways).
it worked- but I ran into a case with a 2204 where commands were being lost
right and left. Best be safe.
For target mode, or things called if we call isp_handle_other response- note
that we might have dropped locks by changing the output pointer so we bail
from the loop. It's the responsibility of the entity dropping the lock to
make sure that we let the f/w know we've read thus far into the response
queue (else we begin processing the same entries again- blech!).
MFC after: 1 day
the upcoming 7.4 family (7xxx controllers).
- improved error reporting and handling
- more diagnostic output
- add extra command packet definitions
- merge sources again with -stable
by removing parentheses. The main bug is in gcc: on machines with
64-bit longs and 64-bit long longs,
(unsigned long long)rdp->total_sectors / ((1024L * 1024L) / DEV_BSIZE))
has type plain unsigned long instead of the correctly promoted type
unsigned long long, so it can not be printfed using %llu format. Even
1ULL / 1L is mispromoted. Anyway, casting the correct operand
automatically avoids the problem. We do not want to to pessimize the
division; we just want to convert to a common maximal type for printing.
Some buggy firmware workarounds. Fix some endian bugs.
These reduce the diffs from NetBSD, but NetBSD does have more changes since
my last manual merge.
Link if only ATAPI device in kernel config
Remove unused #includes
Rearrange a bit in ata-raid to make diff against -stable smaller
Enable wc as default again, dunne how this happend...
This makes other power-management system (APM for now) to be able to
generate power profile change events (ie. AC-line status changes), and
other kernel components, not only the ACPI components, can be notified
the events.
- move subroutines in acpi_powerprofile.c (removed) to kern/subr_power.c
- call power_profile_set_state() also from APM driver when AC-line
status changes
- add call-back function for Crusoe LongRun controlling on power
profile changes for a example
Add code to properly detach/attach disks that are part of a RAID.
Mark a disk that is attached on an ATA channel belonging to a
RAID as a spare disk that can be used for rebuilding failed RAID1's.
Add support for rebuilding failed RAID1's.
Several fixes to the detach/attach code.
For replacing a disk in a failed RAID1 do the following:
Find the controller channel# of the failed disk.
Exec 'atacontrol detach <channel#>' to free the disk from the system.
Replace the failed disk with a new one of at least the same size.
If your have your disks in drawers/enclosures this can be done with
the system still running.
Exec 'atacontrol attach <channel#>' to add the disk to the system and
mark it as a valid spare for rebuild.
Exec 'atacontrol rebuild <array#>'
The system will rebuild the array on the fly, the array can still
be used during this, although with slower performance.
Please let me know of any problems with this!
Sponsored by: Advanis Inc.
MFC after: 2 weeks
in most machines of the Sun Ultra series. This is a port of the NetBSD
driver which I enhanced to make use of the gather functionality and the
configurable RX buffer offset to avoid copying all received/sent packet
(instead, packets will be directly DMAd from mbuf chains and into mbuf
clusters now).
device drivers for bus system with other endinesses than the CPU (using
interfaces compatible to NetBSD):
- bwap16() and bswap32(). These have optimized implementations on some
architectures; for those that don't, there exist generic implementations.
- macros to convert from a certain byte order to host byte order and vice
versa, using a naming scheme like le16toh(), htole16().
These are implemented using the bswap functions.
- stream bus space access functions, which do not perform a byte order
conversion (while the normal access functions would if the bus endianess
differs from the CPU endianess).
htons(), htonl(), ntohs() and ntohl() are implemented using the new
functions above for kernel usage. None of the above interfaces is currently
exported to user land.
Make use of the new functions in a few places where local implementations
of the same functionality existed.
Reviewed by: mike, bde
Tested on alpha by: mike
1/ conditionalise (#if 0) function that is not used.
Unused code left in place for netBSD compatibility.
2/ Recode loop to convince gcc that it does initialise a variable
(use do-while instead of for() so gcc knows that we always go through
at least once. Feel free to check my logic.
code into cardbus and s/pci/cardbus. This exposes a few pci_*
functions that are now static.
This work is similar to work Justin posted to the mobile list about a
year or two ago, which I have neglected since then.
This is a subset of his current work with the multiple inheritance
newbus architecutre. When completed, that will eliminate the need for
pci/pci_private.h.
Similar work is needed for the cardbus_cis and pccard_cis code as well.
the inter-value histogram for 2000 samples. If the width is 3 or less
for 10 consequtive samples, we trust the counter to be good, otherwise
we use the *_safe() method.
This method may be too strict, but the worst which can happen is that
we take the performance hit of the *_safe() method when we should not.
Make the *_safe() method more discriminating by mandating that the three
samples do not span more than 15 ticks on the counter.
Disable the PCI-ident based probing as a means to recognize good
counters.
Inspiration from: dillon and msmith
latch the acpi timer, resulting in weird deltas. The problem is severe
enough to adversely effect the timecounter code.
Default to the 'safe' version of the get-timecount function. The probe
will override it if a known-good chipset is found. This is temporary
until a more complete solution is found.
Reviewed by: phk
AIOGCAP ioctl reports software-emulated formats. It defaults to on. People
who use performance-sensitive audio software and do not want it to pick a
software-emulated audio format instead of one supported by their hardware
should turn it off.
This unbreaks isdnphone(1) on systems with PCM-only sound cards.
Approved by: cg
New locks are:
- pgrpsess_lock which locks the whole pgrps and sessions,
- pg_mtx which protects the pgrp members, and
- s_mtx which protects the session members.
Please refer to sys/proc.h for the coverage of these locks.
Changes on the pgrp/session interface:
- pgfind() needs the pgrpsess_lock held.
- The caller of enterpgrp() is responsible to allocate a new pgrp and
session.
- Call enterthispgrp() in order to enter an existing pgrp.
- pgsignal() requires a pgrp lock held.
Reviewed by: jhb, alfred
Tested on: cvsup.jp.FreeBSD.org
(which is a quad-CPU machine running -current)
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Convert to using a kthread rather than timeout() to avoid problems
with the interpreter sleeping.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Use _ADR as well as _BBN to get our bus number.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The ACPI global lock acquire takes a timeout value. I'm not sure what
we should do about timeouts on it; a deadlock against this lock is
catastrophic.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Kill off the timeouts that used to read _BIF and _BST. These are
invoked when the battery is actually read. timeout() is dangerous
in combination with ACPI, as the interpreter can block.
This driver still needs more work.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Add AcpiBatteryIsPresent helper to determine whether a battery device
is inserted.
Add ACPI_ALL_DRIVERS to the list of debug layers, now that we own the
namespace for this.
Pr:
OUT status. We are, apparently, required to force the f/w to log back in
if we want to try and talk to that disk again. This means either issuing
a LOGIN LOCAL LOOP PORT mailbox command, or by issuing a LIP. I've elected
to issue a LIP because this has a better chance of waking up the disk which
clearly just crashed and burned.
These should not occur at all. If they do, they should be darned rare.
MFC after: 1 week
to be able to use 48bit addressing mode, but says the 48bit
size of the disk is 0, which according to spec means it can
address zero sectors in 48bit mode, why then say it supports
48bit mode at all..
If you want QLogic to look at a potential f/w problem for FC cards, you really
have to provide them info in the format they expect. This involves dumping
a lot of hardware registers (> 300 16 bit registers) and a lot of SRAM
(> 128KB minimum). Thus all of this code is #ifdef protected which will
become an option so that the memory allocation of where to dump the crash
image is pretty expensive. It's worth it if you have a reproducible problem
because they have some tools that can tell them, given the f/w version,
the precise state of everything.
MFC after: 1 week
Appologies for making this one bulk commit, but I have tested all these
changes together and don't want to break anything by trying to disentangle
it.
o Make debugging a sysctl/tunable
o Remove flags word from yenta chip info, it is unused
o Make 16-bit card I/O range and 32-bit card I/O range tunables
o Start the rename of pccbb to cbb to match NetBSD by misc renames.
o Kill the now bogus list of softcs to create kthread. Instead, just
create the kthread in the attach routine.
o Remove sc_ from some structure names. It isn't needed.
o Refine chipset lookup code.
o Match generic PCI <-> CardBus bridges. We specifically don't generically
match PCI PCMCIA bridges because they are not, with one exception, yenta
devices.
o Add some comments about the why we need to have a function table ala
OLDCARD
o The PCI interrupt routing by using the ExCA registers is needed for
for all bridges, per the spec, not just TI ones.
o Collapse TOPIC95 and TOPIC95B.
o Using the ToPIC 97 and 100 datasheets, try to support these bridges better,
but more work is needed.
o Generally clarify some XXX comments and add them in a few places where
things didn't look right to me.
o Move interrupt generating register access until after we establish an ISR.
o Add support for YV and XV cards. X and Y are numbers to be determined
later (but maybe never).
o factor powerup code for 16-bit and 32-bit cards.
o When a card supports more than one voltage, prefer the lowest supported
volage. Windows does this, and MS's design guides imply this is the
right thing to do.
o Document race between kthread_exit(0) and kldunload's unmapping of pages
that John Baldwin and I discovered.
o Debounce the CSC interrupt a little better.
o When a 16-bit card is inserted when we don't have a pccard child,
warn about it better. Ditto for 32-bit card.
o Ack ALL the interrupt bits that we get, not just 0x1.
o maybe a couple minor style nits corrected.
the structure definitions come from NetBSD to make it easier to share card
definitions. The driver only acts as a shim between the pci bus and the
sio driver. Later pci parallel ports could also be supported through this
driver. Support for most single and multiport pci serial cards should be
as simple as adding its definition to pucdata.c
Tested with the following pci cards:
Moxa Industio CP-114, 4 port RS-232,RS-422/485
Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports
Netmos NM9835 PCI-2S-550, 2 port RS-232
be compiled. Old tty ioctls are still used (possibly ifdef'ed) in at
least the following programs in the src tree:
atc des ee fontedit gdb gdbserver lock ntp perl5 tcsh telnet top vttest
rp.c:
Unremoved used variables so that the support for old ioctls actually
compiles.
Not tested at runtime by: bde
ACPI_NO_SEMAPHORES, ASR_MEASURE_PERFORMANCE, AST_DEBUG, ATAPI_DEBUG,
ATA_DEBUG, BKTR_ALLOC_PAGES, BROOKTREE_ALLOC_PAGES, CAPABILITIES,
COMPAT_SUNOS, CV_DEBUG, MAXFILES, METEOR_TEST_VIDEO, NDEVFSINO,
NDEVFSOVERFLOW, NETGRAPH_BRIDGE, NETSMB, NETSMBCRYPTO, PFIL_HOOKS,
SIMOS, SMBFS, VESA_DEBUG, VGA_DEBUG.
Start using #! to comment out negative options and ## to comment out
broken options.
atapi-all.c:
Fixed rotted bits that were hiding under ATAPI_DEBUG.
atapi-cd.c:
#include "opt_ata.h" so that ACD_DEBUG is actually visible.
ata/atapi-tape.c
#include "opt_ata.h" so that AST_DEBUG is actually visible.
descriptors. This simplifies code for jumbo frames.
- Cleaned up coding conventions to make code more unix-like.
- Cleaned up code in if_em_fxhw.c and if_em_phy.c.
Added relevant comments.
MFC after: 1 week
More cleanups of the RAID1 failure mode code.
Add functionality that writes the changed RAID config setup
back to the disks (in controller BIOS specific format), so
that a reboot will make the BIOS pick up the changed config.
1) We shouldn't continue when we get a RX complete because we ack it
and the TX complete.
2) Fix a couple of spl leaks
(why splbio is needed in ISR, I cannot understand).
MFC after: 3 days
Also, add some 'const's to supress warnings. (Submitted back to NetBSD).
The original logs from NetBSD:
----------------------------
revision 1.90
date: 2001/12/03 01:47:12; author: augustss; lines: +4 -4
Handle vendor/product lookup with a common routine.
----------------------------
revision 1.89
date: 2001/12/02 23:25:25; author: augustss; lines: +18 -2
Add a subroutine to search for a vendor/product pair.
----------------------------
Original NetBSD log messages are:
----------------------------
revision 1.23
date: 2001/12/12 15:48:18; author: augustss; lines: +132 -114
Add a scanner quirk for keeping the pipes open between device opening.
Idea from Enami.
----------------------------
revision 1.22
date: 2001/12/03 01:47:13; author: augustss; lines: +8 -16
Handle vendor/product lookup with a common routine.
----------------------------
revision 1.21
date: 2001/12/01 09:42:39; author: enami; lines: +4 -4
Shorten wmesg so that they can be distinguished in ps/top output.
----------------------------
revision 1.12
date: 2001/01/23 14:04:14; author: augustss; lines: +7 -1
Make sure driver attach/detach events are generated in a
consistent manner.
----------------------------
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
From the NetBSD logs:
revision 1.45
date: 2001/11/29 11:07:12; author: augustss; state: Exp; lines: +12 -2
Plug a memory leak in an error case.
----------------------------
revision 1.43
date: 2001/10/19 15:30:25; author: nathanw; state: Exp; lines: +5 -3
Match printers that report their interface as IEEE 1284 in addition to
bidirectional.
o Call bus_generic_setup_intr and check its return value. Don't setup
func until we successfully get the interrupt from our parent.
o Add comments about some maybe questionable stuff so I can check later
to make sure that it really is that way.
o Don't allow INTR_TYPE_FAST. Since we are sharing the interrupt between
CSC and the functions, they can't be FAST because fast interrupts can't
be shared.
o Add the same workaround for resume that we have in OLDCARD.
o Also, return the error from bus_generic_resume rather than ignoring it.
of I/O in 1.5. It looks like I got it right only for some of the
cases. Instead, allow ISA addresses as a special case. Most PCI
bridges decode this range. I need to investigate PCI bridges better
to know if this is always true or not, but for now assume that it is
since that seems to be the most common case.
# We need to allocate addresses better for the pccard stuff...
Submitted by: phk, mitsunaga-san
to fix their code.
ata stuff:
Change name of ar_attach to not colide with existing ar_attach in if_ar.c.
usb stuff:
Create a dummy function to satisfy a call to it when in DEBUG mode.
check is complicated by the fact that the Adaptec 5400S cards claim to use
1.x firmware also. PERC2/QC 1.x firmware is not compatible with this driver
and will cause a system hang.
MFC after: 3 days
disable MWI on 2300
based on function code, set an 'isp_port' for the 2312- it's a
separate instance, but the NVRAM is shared, and the second port's
NVRAM is at offset 256.
+ Enable RIO operation for LVD SCSI cards. This makes a *big* difference
as even under reasonable load we get batched completions of about 30
commands at a time on, say, an ISP1080.
+ Do 'continuation' mailbox commands- this allows us to specify a work
area within the softc and 'continue' repeated mailbox commands. This is
more or less on an ad hoc basis and is currently only used for firmware
loading (which f/w now loads substantially faster becuase the calling
thread is only woken when all the f/w words are loaded- not for each
one of the 40000 f/w words that gets loaded).
+ If we're about to return from isp_intr with a 'bogus interrupt' indication,
and we're not a 23XX card, check to see whether the semaphore register is
currently *2* (not *1* as it should be) and whether there's an async completion
sitting in outgoing mailbox0. This seems to capture cases of lost fast posting
and RIO interrupts that the 12160 && 1080 have been known to pump out under
extreme load (extreme, as in > 250 active commands).
+ FC_SCRATCH_ACQUIRE/FC_SCRATCH_RELEASE macros.
+ Endian correct swizzle/unswizzle of an ATIO2 that has a WWPN in it.
MFC after: 1 week
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
to ExCA register sets. These registers exist in both ISA and PCI
devices in a couple different ways, and this will provide a common
base for future building. This code is a rehash of the pccbb 16-bit
code, which was a rehash of the pcic code, which was a rehash of the
netbsd i82365 code. More hashing to come.
apply to this file. The correct message is:
throw_rude_remark: Make sure we're holding the config lock before
proceeding. There's no reason to assume that this
has ever happened, but the alternative might be a
double fault.
uhub.c: revision 1.37
usb.4: revision 1.30
usb.c: revision 1.38
usb.h: revision 1.40
usb_port.h: revision 1.21
usb_subr.c: revision 1.65
usbdi.h: revision 1.40
Split the attach/detach events up into device, driver and controller
attach and detach events.
The commit message from NetBSD was:
date: 2000/02/02 07:34:00; author: augustss; state: Exp;
Change the USB event mechanism to include more information
about devices and drivers. Partly from FreeBSD.
Also rework usbd to take these new event types into account.
for success, non-zero otherwise. The maestro and maestro3 drivers were
returning the format code, which was being interpreted as a failure code.
Fixed. No one seems to have noticed that the maestro driver was broken,
but I'll fix it anyways.
MFC after: 2 weeks
* be more specific in verbose boot messages
* allow the feeder subsystem to veto pcm* attaching if there is an error
initialising the root feeder
* don't free/malloc a new tmpbuf when resizing a snd_dbuf to the same size as
it currently is
* store the feeder description in the feeder structure instead of mallocing
space for it
usb.c: revision 1.39
revision 1.39
date: 2000/02/22 11:30:56; author: augustss; lines: +7 -1
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
usb.c: revision 1.41
revision 1.41
date: 2000/03/16 00:46:38; author: augustss; lines: +2 -2
Make the USB event queue longer. Mine overflows before the
(user-land) event handler has started. But then I have
about 25 devices connected. :)
ohci.c: revision 1.72 and 1.73
ohcivar.h: revision 1.19 and 1.20
uhci.c: revision 1.85
usbdi.h: a small part of revision 1.40
usbdivar.h: revision 1.47
Relevant commit messages from NetBSD are:
date: 2000/02/22 11:30:54; author: augustss; state: Exp;
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
----------------------------
date: 2000/02/01 05:42:53; author: augustss; state: Exp;
Put some #ifdefs around power and shutdown hooks.
usb.c: -r1.35 - 1.37
usb_port.h: tiny bit of -r1.26 + an extra bit in the FreeBSD config section.
revision 1.37
date: 2000/01/24 18:35:51; author: thorpej; state: Exp; lines: +7 -1
Use config_pending.
----------------------------
revision 1.36
date: 1999/12/22 23:54:09; author: augustss; state: Exp; lines: +2 -2
Use the flags `locator' to govern if devices are detected early or
late during cold boot.
----------------------------
revision 1.35
date: 1999/12/20 02:12:23; author: augustss; state: Exp; lines: +8 -5
Make sure tsleep() is not called during cold boot.
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
extensively as none of my testboxes have speakers or an audio source at
present, but the chains built look correct and reading /dev/audio (ulaw,
translated from signed 16 bit little-endian) gives values within the
expected range for silence.
default format for the chosen subdevice cannot be obtained return an error
instead of returning success with an indeteterminate format selected.
note that this should never happen once the feederchain builder works for
recording.
ohci.c: -r1.69 to 1.71
ohcireg.h: -r1.14
Some of these deltas are based upon patches that we submitted back to
NetBSD. They got manifested slightly differently though, so I've brought
back those differences to bring our code bases closer together.
The logs from the NetBSD version of ohci.c:
revision 1.71
date: 2000/02/01 05:42:52; author: augustss; state: Exp; lines: +13 -2
Put some #ifdefs around power and shutdown hooks.
----------------------------
revision 1.70
date: 2000/01/31 22:35:13; author: augustss; state: Exp; lines: +7 -7
Rename TAILMASK to HEADMASK, since it really masks the head pointer.
From FreeBSD.
----------------------------
revision 1.69
date: 2000/01/31 22:09:13; author: augustss; state: Exp; lines: +18 -14
Change where the has table for physical-to-virtual address translation
is handled. Partly from FreeBSD.
ohci.c: -r1.68
ohcireg.h: -r1.13
date: 2000/01/31 20:17:25; author: augustss; state: Exp;
Fiddle with over-current protect when turning on port power to make
things work for some OHCI controllers.
uhci.c: -r1.82
uhcivar.h: -r1.22
date: 2000/01/26 10:04:39; author: augustss; state: Exp;
Try to avoid accessing the HC if it is dead. Suggested by mycroft.
revision 1.125
date: 2000/09/23 21:00:10; author: augustss; state: Exp; lines: +19 -3
Avoid "bandwidth reclamation" for control transfers. The kue device chokes
on it.
uhci.c: -r1.124
uhcireg.h: -r1.13
date: 2000/08/13 18:20:14; author: augustss; state: Exp;
Fix race condition when unlinking xfers. Thanks to IWAMOTO Toshihiro
<iwamoto@sat.t.u-tokyo.ac.jp> for analyzing the problem and suggesting a fix.
Fixes PR 10662.
uhci.c: -r1.123 (and a tiny bit of -r1.92)
uhcivar.h: -r1.32
date: 2000/08/13 16:18:09; author: augustss; state: Exp;
Implement what in Intel-speech is known as "bandwidth
reclamation". It means that we continously poll USB devices
that have a pending transfer instead of polling just once
every ms. This speeds up some transfers at the expense of
using more PCI bandwidth.
uchireg.h: -r1.12
uchi.c: -r1.121
date: 2000/07/23 19:43:38; author: augustss; state: Exp;
Be a little more explicit and careful about setting links in TDs and QHs.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
likely looking rate calculation.
Install interrupt handler before calling ich_init as the initialization
occasionally generates spurious interrupts.
These changes are derived from cg's work in progress version of this
driver.
at insert time. When asking gibbs for approval for an MFC, this was
his reply:
1) It leaks memory if it can't allocate a path.
2) It defers allocation of aic->path until the call to scan the
bus. This means the path may be NULL when an interrupt occurs
prior to the call to scan the bus (stray bus reset for instance),
which will lead to a panic.
3) The driver in current doesn't recover from the failure to allocate
aic->path. The driver doesn't check during normal operation if
the path is NULL, so again a panic will result.
4) aic_cam_rescan calls malloc with M_WAITOK. aic_cam_rescan is called
from attach where it isn't necessarily safe to sleep.
5) And most importantly, it co-opts the xpt_periph from the driver level.
This was never part of the design (xpt_periph used to be static). Making
a call of this type may completely confuse the XPT if other XPT operations
are ongoing.
In the long term, Justin and Warner agreed to implement solution where
CAM itself will initiate the bus rescan if a new bus is added. For
the time being (and in particular in light of the upcoming 4.5
release), we now have camcontrol available on the boot floppy, and can
have pccardd initiate the rescan through it.
previous commit, it should always print due to lack of {} around the
second line in the if statement. The message should likely say
something more like "There's no hardware responding at this IRQ.
Device not present (or disbaled)," but that is too long. We generally
don't give elementary advise in device driver messages anyway. Be
that as it may, the problem with it printing all the time should be
corrected.
One to notify the system that the MTU for VLAN can be 1500 so the vlan
will automatically be configured with a 1500 MTU the other is to ignore
the error case if the received frame is to long.
The frame size notification came from code in the SIS driver, and
the support for long frames derived from the NetBSD Tulip driver.
Tested on: 4 port D-Link adapter DFE-570TX 4 Intel 21143
Netgear card with 82c169 PNIC 10/100BaseTX
Reviewed by: ru (manpage), wpaul (not objected to), archie
Approved by: imp
Obtained from: NetBSD
o Remove bogus flags that aren't used (if we need them in the future, we can
add them back).
o Add support for the TI-1031. This is the only YENTA compatible PCI-PCMCIA
bridge that I'm aware of (all the others are PCIC on a PCI bus, which is
different).
Seigo Tanimura (tanimura) posted the initial delta.
I've polished it quite a bit reducing the need for locking and
adapting it for KSE.
Locks:
1 mutex in each filedesc
protects all the fields.
protects "struct file" initialization, while a struct file
is being changed from &badfileops -> &pipeops or something
the filedesc should be locked.
1 mutex in each struct file
protects the refcount fields.
doesn't protect anything else.
the flags used for garbage collection have been moved to
f_gcflag which was the FILLER short, this doesn't need
locking because the garbage collection is a single threaded
container.
could likely be made to use a pool mutex.
1 sx lock for the global filelist.
struct file * fhold(struct file *fp);
/* increments reference count on a file */
struct file * fhold_locked(struct file *fp);
/* like fhold but expects file to locked */
struct file * ffind_hold(struct thread *, int fd);
/* finds the struct file in thread, adds one reference and
returns it unlocked */
struct file * ffind_lock(struct thread *, int fd);
/* ffind_hold, but returns file locked */
I still have to smp-safe the fget cruft, I'll get to that asap.
instead of relying on the previous filters to be present.
Back out r1.125, as a reset is needed to unload any existing microcode,
(which clears the multicast addresses), as it is superceded by this change.
mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
hw.midi.debug and hw.midi.seq.debug to 1 to enable debug log.
- Make debug messages human-frendly.
- Implement /dev/music.
- Add a timer engine required by /dev/music.
- Fix nonblocking I/O.
- Fix the numbering of midi and synth devices.
firmware to delay completion of commands so that it can attempt to batch
a bunch of completions at once- either returning 16 bit handles in mailbox
registers, or in a resposne queue entry that has a whole wad of 16 bit handles.
Distinguish between 2300 and 2312 chipsets- if only because the revisions
on the chips have different meanings.
Add more instrumentation plus ISP_GET_STATS and ISP_CLR_STATS ioctls.
Run up the maximum number of response queue entities we'll look at
per interrupt.
If we haven't set HBA role yet, always return success from isp_fc_runstate.
MFC after: 2 weeks
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
This gives a bit of a sluggish console, but it prevents the console from
getting stuck if we poll too fast, as well as other badness on certain
machines.
2. Fix a test for != 0 that should have been > 0.
Noticed by: Jamey Wood <Jamey.Wood@Sun.COM> and myself
Submitted by: tmm (2)
- Move from msleep/wakeup to condvar.
- Return either zero or a positive errno value from a function.
Return additional result via references.
- Unify the typedef of callback functions.
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
a packed array so sizeof work. This broke RFMON mode and passing
up 802.11 packets.
The Linux emulation code was derived from the open source Linux driver to
maintain compatibility.
LEAP support is added, hints from Richard Johnson. I've verified this
locally with PC350v42510.img firmware. More bug fixing from Marco to
fix long passwords.
Change DELAYs in flash part of driver to FLASH_DELAY which uses tsleep
so it doesn't look like your system died during a flash update.
Install header files in /usr/include/dev/an
Cleanup some ifmedia bugs add "Home" key mode to ifmedia and ancontrol.
This way you can manage 2 keys a little easier. Map the home mode into
key 5. Enhance ifconfig to dump the various configured SSIDs. I use
a bunch of different ones and roam between them. Use the syntax similar
to the WEP keys to deal with setting difference SSIDs.
Bump up up the Card capabilities RID since they added 2 bytes to it
in the latest firmware. Thankfully we changed it from a terminal
failure so the card still worked but the driver whined.
Some cleanup patches from Marco Molteni.
Submitted by: Richard Johnson <raj@cisco.com>
Marco Molteni <molter@tin.it>
and myself
Various checks: David Wolfskill <david@catwhisker.org>
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Obtained from: Linux emulation API's from Aironet driver.
socreate(), rather than getting it implicitly from the thread
argument.
o Make NFS cache the credential provided at mount-time, and use
the cached credential (nfsmount->nm_cred) when making calls to
socreate() on initially connecting, or reconnecting the socket.
This fixes bugs involving NFS over TCP and ipfw uid/gid rules, as well
as bugs involving NFS and mandatory access control implementations.
Reviewed by: freebsd-arch
In order of importance:
* Make ugen use updated frlengths.
* More tests for NULL pipes.
* Generate better error codes on bulk write.
* Error messages in general.
(1) Don't attempt aquire the non-recursive lock sio_lock recursively.
Doing so caused unbounded recursion in some setups. E.g., if DDB,
BREAK_TO_DEBUGGER and WITNESS are configured; if the debugger is
entered using a break, then WITNESS will actually detect the invalid
recursion and will add to it attempting to print a message about it.
(2) Don't use sio_lock before it has been initialized. The old check
(sio_inited != 0) didn't work when sio_inited was boolean because
sio_inited was set too early, and became just wrong when sio_inited
was changed to a tri-state variable in rev.1.348.
Reported and fixed in another way by: fenner (1)
see people trip over it. Do not set the FIFO trigger to just before it
would otherwise overflow. Give it a little more slop so characters aren't
lost if the interrupt is delayed by other system activities.
MFC maybe: 7 days
- Temporary fix a bug of Intel ACPI CA core code.
- Add OS layer ACPI mutex support. This can be disabled by
specifying option ACPI_NO_SEMAPHORES.
- Add ACPI threading support. Now that we have a dedicate taskqueue for
ACPI tasks and more ACPI task threads can be created by specifying option
ACPI_MAX_THREADS.
- Change acpi_EvaluateIntoBuffer() behavior slightly to reuse given
caller's buffer unless AE_BUFFER_OVERFLOW occurs. Also CM battery's
evaluations were changed to use acpi_EvaluateIntoBuffer().
- Add new utility function acpi_ConvertBufferToInteger().
- Add simple locking for CM battery and temperature updating.
- Fix a minor problem on EC locking.
- Make the thermal zone polling rate to be changeable.
- Change minor things on AcpiOsSignal(); in ACPI_SIGNAL_FATAL case,
entering Debugger is easier to investigate the problem rather than panic.
to Phil Kernick:
"The problem is that in full duplex mode, the Conexant chip always reports a
carrier lost error, even when the frame is successfully sent. So, if we
have a Conexant chip, then ignore carrier lost when in full duplex
mode."
Since the Xircom chips seem to have the same issue and since we already
have a workaround for this, just expand the workaround test to also
check for DC_IS_CONEXANT().
to a label is inside an #ifdef block, then the label should *also* be
inside an #ifdef block. Hide the "done:" label which is only used if
DEVICE_POLLING is enabled under #ifdef DEVICE_POLLING.
must be cleared to prevent machine hanging (presently aflicts -current
and -stable).
Problem reported by Bruce Montague <brucem@cse.iitkgp.ernet.in>
PR: kern/29769 (probably)
otherwise breaks on the Alpha arch. I think this is wrong since i'd
actually like to probe for a PC architecture, not for a particular CPU
type. Anyway, now it's again the way it used to be.
sense, and mode select into their 10 byte equivalents. Eventually the
da(4) driver will become more intelligent about this, or at least allow
umass(4) to pass quirks in directly. However, this is a functional
workaround until a better fix is implemented.
- Use the 6 to 10 conversion function to allow the ATAPI and UFI command
sets to emulate 6 byte commands with 10 byte commands.
- Use the ATAPI command set rather than UFI for the ScanLogic SL11R-IDE
as it supports the SYNCH_CACHE command.
- Enable ATAPI command set support.
- Pass READ/WRITE_12 commands through for UFI support as the UFI spec
says they should be supported.
- Update a comment in the UFI translation function since we handle
MODE_SELECT.
- The MD functions critical_enter/exit are renamed to start with a cpu_
prefix.
- MI wrapper functions critical_enter/exit maintain a per-thread nesting
count and a per-thread critical section saved state set when entering
a critical section while at nesting level 0 and restored when exiting
to nesting level 0. This moves the saved state out of spin mutexes so
that interlocking spin mutexes works properly.
- Most low-level MD code that used critical_enter/exit now use
cpu_critical_enter/exit. MI code such as device drivers and spin
mutexes use the MI wrappers. Note that since the MI wrappers store
the state in the current thread, they do not have any return values or
arguments.
- mtx_intr_enable() is replaced with a constant CRITICAL_FORK which is
assigned to curthread->td_savecrit during fork_exit().
Tested on: i386, alpha
the link rate - some ich motherboards overclock ac97 out of the box.
Will hopefully replace this with a callibration loop in time for 4.5R
freeze.
Problem reported by Luigi Rizzo and fix derived from his code (put
diff in ich.c rather than ac97.c).
MFC after: 3 days
. The main device node now supports automatic density selection for
commonly used media densities. So you can stuff your 1.44 MB and
720 KB media into your drive and just access /dev/fd0, no questions
asked. It's all that easy, isn't it? :)
. Device density handling has been completely overhauled. The old way
of hardwired kernel density knowledge is no longer there. Instead,
the kernel now implements 16 subdevices per drive. The first
subdevice uses automatic density selection, while the remaining 15
devices are freely programmable. They can be assigned an arbitrary
name of the form /dev/fd[:digit]+.[:digit:]{1,4}, where the second
number is meant to either implement device names that are mnemonic
for their raw capacity (as it used to be), or they can alternatively
be created as "anonymous" devices like fd0.1 through fd0.15,
depending on the taste of the administrator. After creating a
subdevice, it is initialized to the maximal native density of the
respective drive type, so it needs to be customized for other
densities by using fdcontrol(8). Pseudo-partition devices (fd0a
through fd0h) are still supported as symlinks.
. The old hack to use flags 0x1 to always assume drive 0 were there is
no longer supported; this is now supposed to be done by wiring the
devices down from the loader via device flags. On IA32
architectures, the first two drives are looked up in the CMOS
configuration records though. On PCMCIA (i. e., the Y-E Data
controller of the Toshiba Libretto), a single drive is always
assumed.
. Other specialities like disabling the FIFO and not probing the drive
at boot-time are selected by per-controller or per-drive flags, too.
. Unit attentions (media has been changed) are supposed to be detected
now; density autoselection only occurs after a unit attention. (Can
be turned off by a per-drive flag, this will cause each Fdopen() to
perform the autoselection.)
. FM floppies can be handled now (on controllers that actually support
it -- not all do these days).
. Fdopen() can be told to avoid density selection by setting
O_NONBLOCK; this leaves the descriptor in a half-opened state where
only a few ioctls are accepted. This is necessary to run fdformat
on a device that uses automatic density selection (since you cannot
autoselect on an unformatted medium, obviously).
. Just differentiate between a plain old NE765 and the enhanced chips,
but don't try more; the existing code was wrong and only misdetected
the chips anyway.
BUGS and TODOs:
. All documentation update still needs to be done.
. Formatting not-so-standard format yields unpredictable results; i
have yet to figure out why this happens. "Standard" formats like
720 and 1440 KB do work, however.
. rc scripts are needed to setup device nodes with nonstandard
densities (like the old /dev/fdN.MMM we used to have).
. Obtaining device flags from the kernel environment doesn't work yet,
thus currently only drives that are present in (IA32) CMOS are
really detected. Someone who knows the odds and ends about device
flags is needed here, i can't figure out what i'm doing wrong.
. 2.88 MB still needs to be done.
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
a GetAllNext response. Otherwise, we won't unswizzle
it correctly. This was found on linux/PPC.
This mandated creating another inline: isp_get_gan_response.
Introduce an additional device flag for those NICs which require the
transmit buffers to be aligned to 32-bit boundaries.
(the equivalen fix for STABLE is slightly simpler because there are
no supported chips which require this alignment there.)
the response queue. Instead of the ad hoc ISP_SWIZZLE_REQUEST, we now have
a complete set of inline functions in isp_inline.h. Each platform is
responsible for providing just one of a set of ISP_IOX_{GET,PUT}{8,16,32}
macros.
The reason this needs to be done is that we need to have a single set of
functions that will work correctly on multiple architectures for both little
and big endian machines. It also needs to work correctly in the case that
we have the request or response queues in memory that has to be treated
specially (e.g., have ddi_dma_sync called on it for Solaris after we update
it or before we read from it). It also has to handle the SBus cards (for
platforms that have them) which, while on a Big Endian machine, do *not*
require *most* of the request/response queue entry fields to be swizzled
or unswizzled.
One thing that falls out of this is that we no longer build requests in the
request queue itself. Instead, we build the request locally (e.g., on the
stack) and then as part of the swizzling operation, copy it to the request
queue entry we've allocated. I thought long and hard about whether this was
too expensive a change to make as it in a lot of cases requires an extra
copy. On balance, the flexbility is worth it. With any luck, the entry that
we build locally stays in a processor writeback cache (after all, it's only
64 bytes) so that the cost of actually flushing it to the memory area that is
the shared queue with the PCI device is not all that expensive. We may examine
this again and try to get clever in the future to try and avoid copies.
Another change that falls out of this is that MEMORYBARRIER should be taken
a lot more seriously. The macro ISP_ADD_REQUEST does a MEMORYBARRIER on the
entry being added. But there had been many other places this had been missing.
It's now very important that it be done.
Additional changes:
Fix a longstanding buglet of sorts. When we get an entry via isp_getrqentry,
the iptr value that gets returned is the value we intend to eventually plug
into the ISP registers as the entry *one past* the last one we've written-
*not* the current entry we're updating. All along we've been calling sync
functions on the wrong index value. Argh. The 'fix' here is to rename all
'iptr' variables as 'nxti' to remember that this is the 'next' pointer-
not the current pointer.
Devote a single bit to mboxbsy- and set aside bits for output mbox registers
that we need to pick up- we can have at least one command which does not
have any defined output registers (MBOX_EXECUTE_FIRMWARE).
MFC after: 2 weeks
pcm0: ac97 codec failed to reset extended mode (0, got 80)
This was due to not masking off the correct extended function bits
in the read value from the extended status reg.
MFC after: 2 days
some Toshiba and Thinkpad laptops.
Wakeup event is generated by power button or sleep button on some
laptops but this also generates SCI interrupt, and shutdown the system
as result. So this is introduced so that acpi driver ignore given
requests for certain period.
the UFI command set. Even with this patch, it's incredibly slow on my
laptop, but at least now it works.
Note that the drive is reported to CAM with the vendor and device IDs from
the device itself, forcing the user to patch the da(4) quirk table
manually.
controllers. There still seems to be some issues with the DRI copying code
for some adapters, at least it doesn't hang the system now. Input would be
appreciated.
PR: 32301
Obtained from: Eric Anhlot <eanholt@gladstone.uoregon.edu>, Joe <joeo@nks.net>
The reason we are required to commit to -current first is so that later
MFC's do not risk the loss of existing bug fixes. Even if this was not
strictly required in -current, it should still be fixed there too.
1. Changed incorrect conditional in fxhw.c which would never
evaluate to true. Thanks to John Polstra for pointing that out.
2. Write to PCI config space by default, enabling memory access and
bus master enable.
Submitted by:Prafulla Deuskar
MFC after:3 days
Similar code was submitted in PR 5559 by Takeshi OHASHI-san, but the
PC Card system has changed much since then, so this is a fresh
implementation.
PR: i386/5559
Submitted by: Takeshi OHASHI
prism2 flag in pccard.conf, but I'm leaving it place for the moment in
case the small sample of PrismII cards that I've tried is not
representative.
MFC After: 30 days
Obtained from: NetBSD
released management apps.
1. Implement poll(). This will check for queued aif's so that a
subsequent ioctl call to retrieve the next aif will not block.
2. Don't catch signals when sleeping on a fib sent from userland. This
causes a race and panic due to the pthread context switcher waking
up the tsleep at inopportune times.
3. Fix some whitespace nits.
MFC after: 3 days
- set sc->acpi_s4bios to 1 by default for hibernation until
OS-initiated S4 transition is implemented.
- change the behavior of acpi_sleep_state_sysctl() if new value is
the same as old one, do nothing instead of EINVAL.
mbuf allocation fails, and fix (i hope) a couple of style bugs.
I believe these printf() are extremely dangerous because now they can
occur on every incoming packet and are not rate limited. They were
meant to warn the sysadmin about lack of resources, but now they
can become a nice way to panic your system under load.
Other drivers (e.g. the fxp driver) have nothing like this.
There is a pending discussion on putting this kind of warnings
elsewhere, and I hope we can fix this soon.
underlying unaligned bcopy) on incoming packets that are already
available (albeit unaligned) in a buffer.
The performance improvement varies, depending on CPU and memory
speed, but can be quite large especially on slow CPUs. I have seen
over 50% increase on forwarding speed on the sis driver for the
486/133 (embedded systems), which does exactly the same thing.
The behaviour is controlled by a sysctl variable, hw.dc_quick which
defaults to 1. Set it to 0 to restore the old behaviour.
After running a few experiments (in userland, though) I am convinced
that doing the m_devget() is detrimental to performance in almost
all cases.
Even if your CPU has degraded performance with misaligned data,
the bcopy() in the driver has the same overhead due to misaligment
as the one that you save in the uiomove(), plus you do one extra
copy and pollute the cache.
But more often than not, you do not even have to touch the payload,
e.g. when you are forwarding packets, and even in the often-cited
case of NFS, you often end up passing a pointer to the payload to
the disk controller.
In any case, you can play with the sysctl variable to toggle between
the two behaviours, and see if it makes a difference.
MFC-after: 3 days
allows us to move the sio softc data structure back into sio.c and
reduce the complexity of the non sio.c sio files.
Submitted by: bde
# I didn't fix the locking issues that bruce also submitted.
loader parameter. This allows us to more easily boot on big memory
configuration machines. hw.pccbb.start_mem. Reflect this in a sysctl
so we can read it from userland.
# Note: we need a TUNABLE_ULONG to do this right. I'll add that to
# kernel.h soon.
request to one that's supported by the bridge. I'm not 100% sure this
is correct, but it makes it easier for the cardbus bridge to allocate
its memory.
Similar code is needed for the I/O range. Also, I'm not sure if I
should be doing this based on memory or pmemory (but likely should do
it based on some flag that tells us to prefetch or not).
Talked about a long time ago with: msmith
NEWCARD. Other patches may be reqiured to sio to prevent a hang on
eject. Also add commented out entries for sio_pccard.c in files.pc98
to match other architectures.
Submitted by: yamamoto shigeru-san
changing. Also change it from 0x44000000 to 0x84000000 for large memory
machines.
# the PCI bus code should do this for us. This is a bandaide, not a
# solution.
click) do not include newline into the buffer. This is exacly how
things worked before my recent changes to the cut'n'paste code and
how they work in 4-STABLE.
card is ejected while we're in this routine.
yamamoto-san's original patch had a small race window for AX88190
chips, which I corrected by limiting the number of iterations we'd try
to reset the bits to be about 15ms rather than forever. This seems to
work for me, but I don't have a large collections of cards based on
this chipset.
Submitted by: YAMAMOTO Shigeru
snooped on. This causes all kinds of Bad Things(tm) to happen since
closing one session will clobber state that's needed for the other
one. This could theoretically be supported if the code was careful,
but until somebody implements that, preventing this will stop people
from unknowingly shooting themselves in the foot.
device cloned, and assign all further devices to depend on it. This
allows us to call dev_depends() on it at module unload time to get rid
of /dev/snp* (in the devfs case, anyway). For this to work, we must
not destroy the device at close time. [Idea stolen from if_tun.]
The above has the following sideaffects: (a) The snp device used by
watch(8) will remain after watch(8) exits. This is probably how it
should have been all along, and how it was before devfs came along.
(b) Module unload doesn't panic if there are any /dev/snp* devices
which haven't been used (and thus previously destroyed). Thus, we can
reenable the unload functionality disabled in rev. 1.65.
PR: 32012
MFC after:3 days
- Add memory barrier definition for sparc64.
Patch sent by David E. O'Brien, approved by maintainer.
- Fix an endianization error of a bus physical address used from SCRIPTS
that made the driver fail on big endian machines as sparc64.
signature, but otherwise behaves just like a normal USB mass-storage
device. Add a new quirk to cover this case, and enable it for C-1
cameras. The quirk enables translation from the C-1 signature to
the normal CSWSIGNATURE value.
Reviewed by: n_hibma
Actually this porting supports Pegasus II chip so I guess some other
devices supported by NetBSD also work. But the devices list are not
included because I cannot confirm if they work.
Obtained from: NetBSD
MFC after: 3 weeks
2. Add OF_getprop_alloc(), a helper function that will malloc() a sufficient
amount of memory and then retrieve a property value into it.
Approved by: benno
Obtained from: NetBSD (1)
disabled unless verbose flag is set. Also fix some messages in terms
of English.
The critical messages and error messages in probe/attach routine are
unchanged by this commit.
Now you can say;
# sysctl hw.acpi.lid_switch_state=NONE
instead of specifying unsupported _Sx object in the system.
Actually, S4B is going to disappear in ACPICA and we already have
hw.acpi.s4bios to distinguish BIOS hibernation or OS hibernation.
pccard layer and rename them PCMCIA_CARD and PCMCIA_CARD2 respectively
(note, this is being done with an eye towards NetBSD integreation so
it is easier to keep lists of cards between us and them in sync).
Use this in the an and wi drivers.
trying something new with the macros here and will likely try to get
them adopted by NetBSD as well as moving them to other drivers. They
make the list more compact and easier to read, the price of rigid to a
schema for generating them (of course there are those that would argue
this isn't bad).
Obtained from: NetBSD's if_wi_pcmcia.c 1.9
off chip that was on one prototype board. However, this appears to be
a design that many chipsets are compatible with its PPEC register set
(eg the Omega 82c094). Through the kindness of the Red Hat developer
David Woodhouse, I now have this datasheet.
I may take the advise of one of the bsd-nomads (whose name
unfortunately escapes me at the moment) and split out all these 16-bit
I/O mapped PCI devices into a separate driver...
that it has one BAR that's mapped to 0x3e0 and is I/O only. It does
not conform to the Yenta spec, like other PCI PCMICA bridges do (eg
the TI 1031, which is mostly a 1131 w/o 32bit card support). It
appears that this chip may also need to not route PCI interrupts
as well.
This chip is used in the NEC Versa 2430CD (and it appears that
sometimes it works, while other times it doesn't) and others in the
2400 series. While the NEC website claims Cardbus support, I can't figure
out how that is possible.
Submitted by: Ben Timby <ben@webexc.com>
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
conf/files) and as a result appears to have been missed in the bulk
KSE update of drivers. This change replaces references to proc
with thread. It has not been compile-tested.
in wdrain during a write. This flag needs to be used in devices whos
strategy routines turn-around and issue another high level I/O, such as
when MD turns around and issues a VOP_WRITE to vnode backing store, in order
to avoid deadlocking the dirty buffer draining code.
Remove a vprintf() warning from MD when the backing vnode is found to be
in-use. The syncer of buf_daemon could be flushing the backing vnode at
the time of an MD operation so the warning is not correct.
MFC after: 1 week
be set to 1 to make FreeBSD and Tru64 coexist peacefully on a dual
boot system and not clobber each other's year in the TOY clock.
(Tru64 uses an offset 52 years higher than one would expect)
Obtained from: NetBSD
MFC After: 1 week
- Now that apm loadable module can inform its existence to other kernel
components (e.g. i386/isa/clock.c:startrtclock()'s TCS hack).
- Exchange priority of SI_SUB_CPU and SI_SUB_KLD for above purpose.
- Add simple arbitration mechanism for APM vs. ACPI. This prevents
the kernel enables both of them.
- Remove obsolete `#ifdef DEV_APM' related code.
- Add abstracted interface for Powermanagement operations. Public apm(4)
functions, such as apm_suspend(), should be replaced new interfaces.
Currently only power_pm_suspend (successor of apm_suspend) is implemented.
Reviewed by: peter, arch@ and audit@
us a lot on older Alphas.
Andrew Gallatin, Thomas V. Crimi, and Peter Jeremy contributed to this
work along with the submitter.
Submitted by: Andrew M. Miklic <miklic@home.com>
- Add a new MIB for battery info expire time in order to make it changeable.
Battery info expire time can be specified by
hw.acpi.battery.info_expire in sec.
- Add own MALLOC type and fix some potential memory leakages.
- Change some frequent printings to verbose printing.
- Stop timeout during acpi_cmbat_get_bst() too. This should reduce
the races with BIF evaluation.
- Remove acpi_cmbat_get_bif() invocation from acpi_cmbat_attach().
This was redundant because this should be called from
acpi_cmbat_timeout() now.
- Give a guaranteed minimum cooling run time to avoid too frequent
cooling system On/Off switching. The minimum cooling run time can be
specified by hw.acpi.thermal.min_runtime in sec.
- Refine message printing (_AC-1 -> NONE).
- Add verbose mode enable/disable capability by hw.acpi.verbose in bool.
Reviewed by: acpi-jp@ folks
in the 21143, instead of giving priority to the receive unit.
This gives a 10-15% performance improvement in the forwarding rate
under heavy load.
Reviewed-by: Bill Paul
while it is on a queue with the queue lock and remove the per-task locks.
- Remove TASK_DESTROY now that it is no longer needed.
- Go back to inlining TASK_INIT now that it is short again.
Inspired by: dfr
This emulates APM device node interface APIs (mainly ioctl) and
provides APM services for the applications. The goal is to support
most of APM applications without any changes.
Implemented ioctls in this commit are:
- APMIO_SUSPEND (mapped ACPI S3 as default but changable by sysctl)
- APMIO_STANDBY (mapped ACPI S1 as default but changable by sysctl)
- APMIO_GETINFO and APMIO_GETINFO_OLD
- APMIO_GETPWSTATUS
With above, many APM applications which get batteries, ac-line
info. and transition the system into suspend/standby mode (such as
wmapm, xbatt) should work with ACPI enabled kernel (if ACPI works well :-)
Reviewed by: arch@, audit@ and some guys
queue, and a mutex to protect the global list of taskqueues. The only
visible change is that a TASK_DESTROY() macro has been added to mirror
the TASK_INIT() macro to destroy a task before it is free'd.
Submitted by: Andrew Reiter <awr@watson.org>
and packet bundling. Make the microcode settings controllable via sysctl
and loader tunables.
Submitted by: Marko Zec <zec@tel.fer.hr>
(with some munging and dynamic sysctl support by me)
Also extend the workaround for Dynamic Standby mode to later '559 chips,
not just the ICH2 variants.
This is taken verbatim from the Intel's e100-1.6.22 release, with
the addition of their LICENSE file at the top.
Submitted by: Marko Zec <zec@tel.fer.hr>
If we get a completion status of RQCS_QUEUE_FULL, it means
that the internal queues are full. Other QLogic boards set
the QFULL SCSI status. But *nooooooooooo*, not the 2300.
MFC after: 1 day
sio_pccard_detach to use new siodetach. Add an extra arg to sioprobe
to tell driver to probe/not probe the device for IRQs.
This incorporates most of Bruce's review material. I'm at a good
checkpoint, but there will be more to come based on bde's further
reviews.
Reviewed by: bde
This might need additional code for hotswapping use, but first
I need to get my hands on actual hw...
Based on docs kindly provided by Promise Inc which we thank for
the close cooperation with the FreeBSD project!.
avoiding EC read errors on some laptops.
- Stop updating Battery info for all user requests
- Update Battery info by notify events and resume method
- Poll Battery info every one minute
Suggested by: takawata
Move sio from isa/sio.c to dev/sio/sio.c. The next step is to break
out the front end attachments, improve support for these parts on
different busses, and maybe, if we're lucky, merging in pc98 support.
It will also be MI and live in conf/files rather than files.*.
Approved by: bde
Tested with: i386, pc98
tracks as /dev/acdNtY.
This solves the problems with having to deal with howmany and which
devices are open.
For hysterical reasons ONLY, make a link to both the acdNa & acdNc devices.
these chips. There is a new hint, hint.pcm.N.hwvol_config, that can be set
to 1 or 0 to select which pins the buttons are connected to. I'm open to
suggestions on where to document this. Also bump the number of playback
channels up to 4.
MFC after: 3 days
- Count the number of this error.
- When the error is detected for the first time, the psm driver will
throw few data bytes (up to entire packet size) and see if it can
get back to sync.
- If the error still persists, the psm driver disable/enable the mouse
and see if it works.
- If the error still persists and the count goes up to 20,
the psm driver reset and reinitialize the mouse. The counter
is reset to zero.
- It also discards an incomplete data packet when the interval
between two consequtive bytes are longer than pre-defined timeout
(2 seconds). The last byte which arrived late will be regarded as
the first byte of a new packet. This is louie's idea.
You may see the following error logs during the above operations:
"psmintr: delay too long; resetting byte count"
"psmintr: out of sync (%04x != %04x)"
"psmintr: discard a byte (%d)"
"psmintr: re-enable the mouse"
"psmintr: reset the mouse"
MFC after: 1 month
- crhold() returns a reference to the ucred whose refcount it bumps.
- crcopy() now simply copies the credentials from one credential to
another and has no return value.
- a new crshared() primitive is added which returns true if a ucred's
refcount is > 1 and false (0) otherwise.
appropriate cache flush that provides MEMORY_BARRIER in between handoffs
between host && RISC processor for the shared memory request/response
queues.
Submitted by: dfr@nlsystems.com
to see if there's an interrupt (avoids PCI parity errors
which can occur on the 2312 if you access some registers
from the host at the same time the RISC on the 2312 is
C accessing them).
MFC after: 1 day
Fix acpi_DeviceIsPresent to check for valid _STA data and to check
the "present" and "functioning" bits.
Use acpi_DeviceIsPresent in acpi_pcib rather than rolling our own
(also broken) version.
with an ifnet structure (so device_get_softc will get one).
If memory allocation fails in mii_phy_probe, don't just march ahead into
a panic- return ENOMEM.
MFC after: 1 week
per-command component that we *don't* try and pass thru CAM. CAM just
is too risky and too much of a pain- structures get copied, but not
all info of interest can be considered safely transported thru all
consumers (including user space) from the incoming ATIO to the outgoing
CTIO- it's just much safer to have a buddy structure, identified by the
command's tag which *does* make it thru safely.
Pay attention to link speed and report 200MB/s xfer speed for a
23XX card in 2GPs mode.
MFC after: 1 week
built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
once so there isn't a window with the ones for the 23XX cards being wrong.
When being verbose, print out some more FC NVRAM values (like framesize).
MFC after: 1 week
. Make internal service routines static.
. Use a consistent ordering of checks in MII_TICK. Do the work in the
mii_phy_tick() subroutine if appropriate.
. Call mii_phy_update() to trigger the callbacks.
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
sio_lock has been initialized. This prevents the low level console
output (kernel printf) from clobbering the sio settings if the system
happens to be in the middle of comstart().
with weird PCI-PCI bridge configurations to work. Defining
PCI_ALLOW_UNSUPPORTED_IO_RANGE causes the sanity checks to pass even
with out of range values.
Reviewed by: msmith
This fixed the problem on the 3 platforms I've been able to test on.
I'm still of the oppinion that the BIOS should take care of this,
however some board makers only apply this when they spot a
SBLive! soundcard, but the problem exists even without a SBLive!.
This fix should probably go somewhere else, but for now I'll
keep it here since we havn't got a central place to put
such things.
problems currently experienced in -CURRENT.
This should fix the problem that the PS/2 mouse is detected
twice if the acpi module is not loaded on some systems.
we're at least consistent with what tcsendbreak(3) is documented
to do.
MFC after: 2 weeks
Note, the MFC will be to sys/dev/dgb/dgm.c on the RELENG_4 branch
I am not sure if this is absolutely necessary on all systems. Yet,
there certainly are motherboards and notebook systems which require
this, although there are other systems which just don't. I hope we
shall know when to do this on which systems, as the development of our
ACPI subsystem progresses... (I know we didn't need this for the APM
resume.)
ppc to go into EPP mode. These 8 inputs are timestamped in polled
loop so their resolution will be nanoseconds but their granularity
will only be 1/hz.
- SC_CUT_SPACES2TABS - when copying text into the cut buffer convert leading
spaces into the tabs;
- SC_CUT_SEPCHARS="XYZ" - treat supplied characters as possible words
separators when the driver searches for words boundaries when doing cut
operation.
Also unify cut code a bit to decrease amount of duplicated code. This fixes
line cut mode, so that it is no longer pads line with useless spaces.
Approved by: ru
seems to set up memory spaces correctly. This change actually did work for
me using -STABLE, XFree86 4.0.3 ~ some snapshot of DRI awhile back. I sent
mail to dfr to no avail, perhaps someone else would like to test it with
DRI.
Anyway, people have been nagging me about this change for awhile, so here's
the commit.
of the rxeoc handler for now. The rxeoc handler will reset the link,
and the NatSemi chip's RX FIFO will overflow on a 32-bit bus once you
start hitting it with 500Mbps or more of traffic.
Also increase the size of the RX ring to 128 descriptors (was 64).
amdpm(4) and smb(4).
This device can be used with userland programs such as sysutils/lmmon
to retrieve sensor information from the motherboard.
PR: kern/23989
Obtained from: Matthew C. Forman <mcf@dmu.ac.uk>
Based on: alpm(4)
- Add workaround for the problematic PnP BIOS which does not assign
irq resource for the PS/2 mouse device node; if there is no irq
assigned for the PS/2 mouse node, refer to device.hints for an
irq number. If we still don't find an irq number in the hints
database, use a hard-coded value.
- Delete unused ivars.
- Bit of clean up in probe/attach.
- Add PnP ID for the PS/2 mouse port on some IBM ThinkPad models.
them if the device arrives.
This should solve the problem where devices that have been disabled eg. in
the BIOS show up with nonsense resources and hang the bootstrap process.
no longer possible to unload the driver module while sound is playing
(which resulted in a panic).
- Fix a similar problem with the sndstat device that I found while looking
at the above.
- Append a newline character to error messages in pcm_unregister()
Reviewed by: cg
MFC after: 10 days
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
correct mode via ancontrol, you can use bpf to sniff raw 802.11 frames.
Who want's to port AirSnort. ;-)
Submitted by: Doug Ambrisko <ambrisko@ambrisko.com> (author)
David Wolfskill <david@catwhisker.org> (port to current)
Avoid fully initialising the ACPI namespace if we are attempting to avoid
parts of it. This is a workaround for some systems that still crash
the interpreter.
Implement the ISA_IVAR_LOGICALID for ISA compatibility. Implement stubs
for other PnP ID-related ivars.
of the adapter object will always result in a change event.
This fixes the problem where a laptop booted without an AC adapter ran
at 100% CPU speed by default.
Submitted by: "Christopher N . Harrell" <cnh@netvmg.com>
Cirrus Logic PD6834
O2micro OZ6836
O2micro OZ6912/6972
O2micro OZ6922
O2micro OZ6933
TI1260 Note: These two aren't on TI's site, but are in
TI1260B http://www.yourvote.com/pci/vendors.txt
Plus comments for other chips found in Windows INF files, and also
referenced in various spots on the net:
* Intel 82092AA 0x12218086 16bit
* smc/Databook DB87144 0x310610b3
* SMC/databook smc34c90 0xb10610b3
* Omega/Trident 82c094 0x00940123?
* Omega/Trident 82c194 0x01941023
* Omega/Trident 82c722 0x07221023?
* Opti 82c814 0xc8141045
* Opti 82c824 0xc8241045
* NEC uPD66369 0x003e1033
more cleanly and consistently in all APCI, PnP BIOS, and "hint"
cases.
NOTE: this doesn't necessarily solve the problem that the PS/2
mouse is not detected after the recent ACPI update.
SIM (as is true for the 1280 and the 12160), then I have to have separate
flags && status for *both* busses. *Whap*.
Implement condition variables for coordination with some target mode
events. It's nice to use these and not panic in obscure little places
in the kernel like 'propagate_priority' just because we went to sleep
holding a mutex, or some other absurd thing.
Remove some bogus ISP_UNLOCK calls. *Whap*.
No longer require that somebody do a lun enable on the wildcard device
to enable target mode. They are, in fact, orthogonal. A wildcard open
is a statement that somebody upstream is willing to accept commands which
are otherwise unrouteable. Now, for QLogic regular SCSI target mode, this
won't matter for a damn because we'll never see ATIOs for luns we haven't
enabled (are listening for, if you will). But for SCCLUN fibre channel
SCSI, we get all kinds of ATIOs. We can either reflect them back here
with minimal info (which is isp_target.c:isp_endcmd() is for), or the
wildcard device (nominally targbh) can handle them.
Do further checking against firmware attributes to see whether we can,
in fact, support target mode in Fibre Channel. For now, require SCCLUN
f/w to supoprt FC target mode.
This is an awful lot of change, but target mode *still* isn't quite right.
MFC after: 4 weeks
applies to. Do more bus # foo things.
Acknowledge Immediate Notifies right away prior to throwing events upstream
(where they're currently being ignored, *groan*)
Capture ASYNC_LIP_F8 as with ASYNC_LIP_OCCURRED. Don't percolate them
upstream as if they were BUS RESETS- they're not.
and cv_wait for mailbox commands to complete if we start them from
here.
Fix residuals for target mode such that we only check the residual and
set it in the CTIO if this is the last CTIO (when we're sending status).
MFC after: 4 weeks
SIM (as is true for the 1280 and the 12160), then I have to have separate
flags && status for *both* busses. *Whap*.
Implement condition variables for coordination with some target mode
events. It's nice to use these and not panic in obscure little places
in the kernel like 'propagate_priority' just because we went to sleep
holding a mutex, or some other absurd thing.
MFC after: 4 weeks
laptops with this chip should test this and report back as I don't have
access to this hardware myself. People with -stable systems should try
the patch at:
http://www.freebsd.org/~wpaul/conexant.patch.gz
Submitted by: Phil Kernick <Phil@Kernick.org>
luns) firmware for the Fibre Channel cards.
We used to assume that if we didn't download firmware, we couldn't know
what the firmware capability with respect to SCCLUNs is- and it's important
because the lun field changes in the request queue entry based upon which
firmware it is.
At any rate, we *do* get back firmware attributes in mailbox register 6
when we do ABOUT FIRMWARE for all 2200/2300 cards- and for 2100 cards
with at least 1.17.0 firmware. So- we now assume non-SCCLUN behaviour
for 2100 cards with firmware < 1.17.0- and we check the firmware attributes
for other cards (loaded firmware or not).
This also allows us to get rid of the crappy test of isp_maxluns > 16-
we simply can check firmware attributes for SCCLUN behaviour.
This required an 'oops' fix to the outgoing mailbox count field for
ABOUT FIRMWARE for FC cards.
Also- while here, hardwire firmware revisions for loaded code for SBus
cards. Apparently the 1.35 or 1.37 f/w we've been loading into isp1000
just doesn't report firmware revisions out to mailbox regs 1, 2 and 3
like everyone else. Grumble. Not that this fix hardly matters for FreeBSD.
MFC after: 4 weeks
A nsp chip does suspend I/O write by 512bytes burst write,
though the chip only has 48 bytes FIFO. The chip assert I/O WAIT
signal to PC-Card bus after the CPU writes more than 48 bytes to
the chip if the SCSI device does not respond immediately in supsend
I/O burst write. If the device does not respond for a while it might
cause PC-Card bus timeout.
The previous work around was to wait the request from SCSI device.
But there are some devices which request bytes for synchronous transfer
immediately. So current work aound is to fill 32bytes FIFO, wait for
FIFO empty and burst write 512-32 bytes for every 512 bytes block.
Submitted-by: Honda-san (the author of the driver)
Obtained-from: NetBSD/pc98
of the module, and allows other modules to depend on and link against
the ACPI module.
Add a sysctl that allows us to retrieve the ACPI CA version number as
well.
some reworking (and consequent cleanup) of the interrupt service code.
Also begin to start a cleanup of target mode support that will (eventually)
not require more inforamtion routed with the ATIO to come back with the
CTIO other than tag.
MFC after: 4 weeks
for the device now (we should really just be parsing a passed-in resource
buffer).
Wrap long lines so this is (more) readable.
Support Address16 and Address32 resources, in the CONSUMER case.
Support DRQs so that we can handle ISA devices.
Support ExtendedIrqs (we ignore most of their attributes)
Add a placeholder device for system memory and system resources. This
takes the place of the nexus placeholder, which only attaches to ISA.
1. Correctly handle commands initiated by the adapter. These commands
are defered to a kthread responsible for their processing, then are
properly returned to the controller.
2. Add/remove disk devices when notified by the card that a container was
created/deleted/offline.
3. Implement crashdump functionality.
4. Support all ioctls needed for the management CLI to work. The linux
version of this app can be found at the Dell or HP website. A native
version will be forthcoming.
MFC-after: 4.4-RELEASE
Second, the TI 1130 need to have the PCI_INTR set, not cleared.
This gets Soren's machine working with NEWCARD again.
# The whole initialization is a mess and needs to be organized ala OLDCARD.
I already deleted it some time ago). This should fix problem people have with
unsefined reference to `MD_PRELOAD_COMPRESSED'.
Submitted by: Manfred Antar <null@pozo.com>
the chip can cause a PCI protocol violation in under certain scenarios.
The workaround is to rewrite the EEPROM to disable Dynamic Standby Mode.
Once the EEPROM is rewritten, the system needs to be rebooted in order
to pick up the new settings.
This has been tested on several ICH2/ICH2-M systems, found in 815E based
boards, and usually identified by the presence of the 82562 ET/EM PHY.
Thanks to: Mike Tansca, Paul Saab for samples of the problematic boards.
if all disks were detached sucessfully;
- use consistent style for return statements and fix several others style
inconsistencies.
Reviewed by: ru
Approved by: phk
Briefly, the significant changes include:
* Way better resource management in pccbb, pccard and cardbus.
* pccard hot-removal now appears to work.
* support pre-fetchable memory in cardbus.
* update cardbus to support new pci bus interface functions.
* Fix CIS reading to no longer use rman_get_virtual().
What's not there, but in the works:
* pccard needs to do interrupt properly and not read the ISR on single
function cards.
* real resource management for pccard
* a complete implementation of CIS parsing
* need to look into how to correctly use mutex in pccbb
This is the first part of a two-part update to NEWCARD. Changes in this
commit are non-functional, and includes the following:
* indentation and other changes to meet style(9).
* other minor style consistancy changes
* addition of comments
* renaming of device_t variables to be consistant across all of NEWCARD.
(note that not all style violations are fixed in this commit -- those that
aren't will be clobbered by the next commit.)
This is the first part of a two-part update to NEWCARD. Changes in this
commit are non-functional, and includes the following:
* indentation and other changes to meet style(9).
* other minor style consistancy changes
* addition of comments
* renaming of device_t variables to be consistant across all of NEWCARD.
(note that not all style violations are fixed in this commit -- those that
aren't will be clobbered by the next commit.)
go into the PLX 9052's interrupt control register and turn on the magic
interrupt enable bit.
Partial thanks are due to OpenBSD for pointing out that the chip is a
PLX 9052 and pointing me to the datasheet PDF.
* add new channels to the end of the list so channels used in order of
addition
* de-globalise definition of struct snddev_info and provide accessor
functions where necessary.
* move the $FreeBSD$ tag in each .c file into a macro and allow the
/dev/sndstat handler to display these when set to maximum verbosity to aid
debugging.
* allow each device to register its own sndstat handler to reduce the amount
of groping sndstat must do in foreign structs.
It appears that a number of PrismII card vendors seem to be doing the
same thing (that is, using the same PCI bridge chip) to support PCI,
but each with their own vendor/product ID. So rather than cut-n-paste
another if statement into the probe routine, it's probably better to
provide support for a table. Adding new devices will be a lot easier
that way.
Add tagged queueing support for new IBM drives.
Add support for Yet Another Promise ATA 100 chip.
Flush disk cache on close.
Dont flush the disk cache on BIO_ORDERED anymore.
Cleanup the tests for DMA on ATAPI devices.
Allow to share ALL irq's even the std irg 14 & 15.
Fix calculation bug in end of media code on CD's.
Add REZERO on opening a CDR/CDRW.
Cleanup ataioctl a bit.
that do not have valid NVRAM. In particular, we were leaving
a retry count set (to retry selection timeouts) when thats
not really what we want. Do some constant string additions
so that LOGDEBUG0 info is useful across all cards.
MFC after: 2 weeks
should be initialized to 0 for PCI adapters which was a side-effect of
the memset in ahc_alloc(). EISA/VL adapters require our unpause value to
include the "levelness" of our interrupt.
This change allows EISA adapters to work again.
PR: 29689, 29471
prevent/workaround TX lockups in this driver. The secret seems to be to
not let the TX DMA queue become too full. If we have too many packets
in the queue, we should wait for them to drain a bit before trying to
queue more. This should prevent the lockup from occurring, and if it
does occur, there is special code in sf_start() to kick the NIC in the
head and get it going again.
Special thanks to Glen Neff for helping me test this fix.
to properly clear the interrupt register on the no error case. Also,
set the mcr register to zero when we find we can't support the chip.
This fixes the hang on sio driver attach problem in the new pci pccard
code that some people have reported. At least on my machine. I'd
like to get this into 4.4.
Submitted by: bde
PR: kern/29742
MFC after: 1 day
probably harmless in this case, since the latter is called on tty
input, which is usually a result of some system call, so we've got
plenty of stack left. It's still nice to fix these things, though, in
case somebody ever decides this driver is a good example of something
(perhaps "what you probably shouldn't do").
night of testing before merging to -stable.
Also added to code to detect TX underruns and automatically increase the
TX threshold to avoid them. Carefully placed diagnostig printf() about
this under #ifdef DIAGNOSTIC to avoid getting any panicky e-mails from
confused users, like I always do with the xl and dc drivers.
common_attach is wrong as common attach initialize some fileds used by
mediainit routine. This was hard to notify because loading driver as kld
lead to mediainit routine being called after common_attach, though probe_phy
is called before.
MFC after: 1 week
- Callers of asleep() and await() have been converted to calling tsleep().
The only caller outside of M_ASLEEP was the ata driver, which called both
asleep() and await() with spl-raised, so there was no need for the
asleep() and await() pair. M_ASLEEP was unused.
Reviewed by: jasone, peter
bypass some extra anti-foot-shooting measures. Currently, its only
effect is to allow detaching a device while it's still open (e.g.,
mounted). This is useful for testing how the system reacts to a disk
suddenly going away, which can happen with some removeable media.
At this point, the force option is only checked on detach, so it
would've been possible to allow the option to be passed with the
MDIOCDETACH operation. This was not done to allow the possibility of
having the force flag influence other tests in the future, which may
not necessarily deal with detaching the device.
Reviewed by: sobomax
Approved by: phk
definitions of all of the ioctls, plus round out all ioctl definitions to
match what exists for linux. Allow ioctls to be called through either the
native or linux interface, though no apps exist (yet) that can take
advantage of native calling.
Correct an off by one in our critical section handling.
SEQADDR always reads the next instruction to execute,
so we must subtract one from its value before making
comparisons with entries in the critical section table.
Print a few additional registers whenever we dump
card state.
Show the SCB_CONTROL and SCB_TAG values for all pending
SCBs in card SCB ram when dumping card state.
aic7xxx.seq:
Fix a bug introduced while optimizing the SDPTR path.
We would ack the SDPTR message twice on Ultra2 or better
chips if it occurred after all data had been transferred
for a transaction.
Change our workaround for the PCI2.1 retry bug on some
chips. Although the previous workaround was logically
correct, its faster method of draining the FIFO seemed
to occassionally confuse the FIFO state. We now drain
the FIFO at half the speed which avoids the problem.
aic7xxx_pci.c:
Chips with the PCI 2.1 retry bug can't handle a 16byte
cachesize. If the cachesize is set to 16bytes, drop
it to 0.
Although it can go higher, it is not safe to so do on arrays with many
members. Compromise by adding a tunable, "hw.aac.iosize_max" that can be
set at boottime. Also document in the aac(4) manpage.
MFC after: 4 weeks
interrupt handler from the upper half, etc. This fixes some serious stability
problems that we were seeing on our production server. These patches have
been tested for almost 6 months and are a highly recommended MFC candidate.
Reviewed by: gibbs, merry, msmith
MFC after: 4 days
to hang or panic kernel by detaching disk from which fs is mounted;
- replace "md" with MD_NAME in yet another place.
Reviewed by: phk
Approved by: phk
a standard cell_t type for the fields of all argument structs. Also
make ihandle_t and phandle_t unsigned to avoid sign extension problems.
Approved by: benno
in the case where there are no interrupts routed for it does not
contain enough space to use it to route an interrupt. In the case
where we need to route an interrupt, throw away the returned buffer
and create a new one containing the interrupt we want.
boot time. Loading as a module once the system is up and running
doesn't make any sense.
- Fix acpi_FindIndexedResource (it would only check the first resource),
changes the calling interface.
- Add a new helper function (acpi_AppendBufferResource) to help building
buffers containing resources.
- Remove the beer-ware license (reqested by phk)
- Reorganise so that the PIIX4 workaround code is kept together, and
switch the workaround function via the timecounter struct, saving
a compare in the read-timecounter codepath. Also indicate that
the workaround is active by changing the timecounter hardware string.
either what's in NVRAM or what the safe defaults would be if we lack NVRAM.
Then we rename cur_XXXX to actv_XXXX (these are the currently active settings)
and the dev_XXX settings to goal_XXXX (these are the settings which we want
cur_XXXX to converge to).
This probably isn't entirely final as yet- but it's a lot closer to now
being what it should be, including allowing camcontrol to actually set
specific settings.
either what's in NVRAM or what the safe defaults would be if we lack NVRAM.
Then we rename cur_XXXX to actv_XXXX (these are the currently active settings)
and the dev_XXX settings to goal_XXXX (these are the settings which we want
cur_XXXX to converge to).
Roll core minor.
either what's in NVRAM or what the safe defaults would be if we lack NVRAM.
Then we rename cur_XXXX to actv_XXXX (these are the currently active settings)
and the dev_XXX settings to goal_XXXX (these are the settings which we want
cur_XXXX to converge to).
size (previously, the transfer size would be rounded up to a multiple of
the block size, which would overflow the buffer).
This fixes panics when doing things like trying to mount audio CD's.
PR: kern/21946
Review Timeout: sos
In file included from ../../../dev/vinum/vinumhdr.h:77,
from ../../../dev/vinum/vinum.c:44:
../../../dev/vinum/vinumext.h:165: warning: redundant redeclaration of `setjmp' in same scope
../../../sys/systm.h:96: warning: previous declaration of `setjmp'
../../../dev/vinum/vinummemory.c:44: warning: redundant redeclaration of `longjmp' in same scope
../../../sys/systm.h:97: warning: previous declaration of `longjmp'
Correctly reintroduce loop_seen_once semantics- that is, if we've never
seen good link, start bouncing commands with CAM_SEL_TIMEOUT. But we
have to be careful to have let ourselves try (in isp_kthread) to check
for loop up at least once.
PR: 28992
MFC after: 1 week
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
storing a flag in the global variable 'linksys' during the probe
routine and reading it during the attach routine. We now have the
ED_VENDOR_LINKSYS vendor code stored in sc->vendor, so check that
instead.
not from the probe routine. This was an oversight when I originally
ported the miibus support to -current, though it was mostly harmless.
We now set the vendor code to the new value ED_VENDOR_LINKSYS in
ed_pccard_Linksys() at probe time. Then ed_pccard_attach() checks
the vendor code, and sets up the miibus if appropriate.
Reviewed by: imp
This code is based on the mp_clock code by phk. It attempts to
detect the PIIX4 (see comments for details) and use a workaround
for its problems.
This code is experimental, and could use some testing and review by a
timekeeping enthusiast.
RSDP, it's now found via a callback).
AcpiOsSleepUsec() went away, use AcpiOsSleep() instead (we could use
AcpiOsStall() too)
AcpiFormatException() was changed to make more sense (it behaves like
our old acpi_strerror() did), so throw acpi_strerror() away (still
#defined in acpivar.h though, we need to sweep these seperately).
events. Otherwise you would see unexpected results if shift or
locking keys are defined to give different actions depending
on other shift/locking keys' state.
Please keep the ukbd module and the kernel in sync, otherwise
the USB keyboard won't work after this change.
MFC after: 10 days
If bus_dma will give us addresses > 32 bits, setup our dma tag
to accept up to 39bit addresses.
aic7770.c:
Update the softc directly rather than use an intermediate
"probe_config" structure.
aic7xxx.c:
Complete core work to support 39bit addresses for bulk data
dma operations. Controller data structures still must reside
under the 4GB boundary to reduce code/data size in the sequencer
and related data structures. This has been tested under Linux
IA64 and will be tested on IA64 for FreeBSD as soon as our port
can run there.
Add bus dmamap synchronization calls around manipulation of
all controller/kernel shared host data structures.
Implement data pointer reinitialation for a second data phase
in a single connection in the kernel rather than bloat the
sequencer. This is an extremely rare operation (does it ever
happen?) and the sequencer implementation was flawed for some
of the newest chips.
Don't ever allow our target role to initiate a PPR. This
is forbidden by the SCSI spec.
Add a few missing endian conversions in the ignore wide pointers
code. The core has been tested on the PPC under Linux and should
work for FreeBSD PPC. As soon as I can test the OSM layer for
FreeBSD PPC, I will.
Move some of ahc_softc_init() into ahc_alloc() now that the
probe_config structure is gone.
Add a 4GB boundary condition on all of our dma tags. 32bit
DAC under PCI only works on a single 4GB "page". Although
we can cross 4GB on a true 64bit bus, the card won't always
be installed in one and we can save code space and cost in
implementing high address support by assuming the high DWORD
address will never change.
Add diagnostics to ahc_search_qinfifo().
Correct a target mode issue with bus resets. To avoid an
interrupt storm from a malicious third party holding the
reset line, the sequencer would defer re-enabling the reset
interrupt until either a select-out or select-in. Unfortunately,
the select-in enable bit is cleared by a bus reset, so a second
reset will render the card deaf to an initiator's attempts to
contact it. We now re-enable bus reset interrupts immediately
if the target role is enabled.
aic7xxx.h:
Remove struct ahc_probe_config.
SCB's now contain a pointer to the sg_map_node so we can perfrom
bus dma sync operations on the SG list prior to queuing a command.
aic7xxx.reg:
Register the Perforce ID for this file with the VERSION keyword
so it is printed in generated files.
Add the DSCOMMAND1 register which is used to access the high
DWORD of address bits.
Add the data pointer reinitialize sequencer interrupt code.
aic7xxx.seq:
Register the Perforce ID for this file with the VERSION keyword
so it is printed in generated files.
Remove code to re-enable the bus reset interrupt after a select-in.
In target mode we cannot defer this operation as ENSELI is cleared
by a bus reset.
Complete 39bit support.
Generate a sequencer inteerrupt rather than handle the data
pointers re-initialitation in the sequencer.
Inline the "seen identify" assertion to save a few cycles.
Short circuit the update of our residual data if we have
fully completed a transfer. The residual is correct from
our last S/G load operation.
Short circuit full SDPTR processing if the residual is 0.
Just mark the transfer as complete.
aic7xxx_93cx6.c:
Synchronize perforce IDs.
aic7xxx_freebsd.c:
Complete untested 39bit support.
Add missing endia conversions.
Clear our residuals prior to starting a command. The
update residual code in the core only sets the residual
if there is one.
aic7xxx_freebsd.h:
Modeify ahc_dmamap_sync() macros to take an offset and a length.
This is how sync operations are performed in NetBSD, and we should
update our bus dma implementation to match.
aic7xxx_inline.h:
Add data structure synchronization helper functions.
Fix a bug in ahc_intr() where we would not clear our unsolicited
interrupt counter after running our PCI interrupt handler. This
may have been the cause of the spurious PCI interrupt messages.
aic7xxx_pci.c:
Adjust for loss of probe_config structure.
Guard against bogus 9005 subdevice information as seen on some
IBM MB configurations.
Add 39bit address support.
MFC after: 10 days
and outputing them in generated files.
Fixed a few other scanner bugs that for some reason didn't show up until
these modifications were made.
MFC after: 10 days
when we get an RX_ERR interrupt rather than the nge_rxeoc() handler. The
rxeoc (end of channel) handler attempts to reinitialize the whole NIC,
which we don't want to do if we only received a bad packet.
. Integrate fdc.h into fd.c, with the removal of ft(4) there's no longer
a reason to scatter things across two files.
. Sanitize comments. Convert them into the style(9)-recommended
multi-line form, make them sentences where apprpriate, etc.
. Declare all functions on top, and declare them in the order they
appear in the file. This order is totally chaotic, but Bruce
convinced me that reordering the file wouldn't make it better either.
. Kill a `possibly uninitialized' warning (only seen with -O2) in
fd_read_status().
. Make the comments at return (0|1) statements in fdstate() consistent.
. Nuke a ``keep the compiler happy'' dummy return at the end of fdstate(),
gcc is smart enough to detect that it would never be reached anyway.
o Much cleanly separate NetBSD(XS) / FreeBSD(CAM) codes.
o Improve tagged queing support (full QTAG).
o Improve quirk support.
o Improve parity error retry.
o Impliment wide negotheation.
o Cmd link support.
o Add copyright of CAM part.
o Change for CAM_NEW_TRAN_CODE.
o Work around for buggy KME UJDCD450.
o stg: add disconnet condition.
o nsp: use suspend I/O.
and more. I thank Honda-san.
conf/options.pc98: add CT_USE_RELOCATE_OFFSET and CT_BUS_WEIGHT
dev/{ct,ncv,nsp,stg}/*_{pccard,isa}.c: add splcam() before calling
attach/detach functions.
Tested by: bsd-nomads
Obtained from: NetBSD/pc98
- All sources are built in a single object, reducing namespace pollution.
- Kill the ready queue, and handle a busy response to mly_start in callers
rather than deferring the command.
- Improve our interaction with CAM:
- Don't advertise physical channels as SCSI busses by default.
- use the SIM queue freeze capability rather than queueing CDBs internally.
- force bus reprobe at module load time.
- Clean up more resources in mly_free.
- Tidy up debugging levels.
- Tidy up handling of events (mostly just code cleanliness).
- Use explanatory macros for operations on bus/target/channel numbers.
a bunch of frames. In this case, the dc_link flag is cleared, and dc_start()
stops draining the if_snd send queue, which results in lots of 'no buffers
available' errors being reported to applications. The whole idea behind
not draining the send queue until the link comes up was to avoid having
the gratuitous ARP being lost while we're waiting for autoneg to complete
after the interface is first brought up. As an optimization, change the
test in dc_start() so that we only bail if dc_link is not set _and_ there
are less than 10 packets in the send queue. If the queue has many frames
in it, we need to drain them. If the queue has a small number of frames
in it, we can hold off on sending them until the link comes up.
MFC after: 1 week
We originally had it such that if the connection topology was FL-loop
(public loop), we never looked at any local loop addresses. The reason
for not doing that was fear or concern that we'd see the same local
loop disks reflected from the name server and we'd attach them twice.
However, when I recently hooked up a JBOD and a system to an ANCOR SA-8
switch, the disks did *not* show up on the fabric. So at least the
ANCOR is screening those disks from appearing on the fabric. Now, it's
possible this is a 'feature' of the ANCOR. When I get a chance, I'll
check the Brocade (it's hard to do this on a low budget).
In any case, if they *do* also show up on the fabric, we should
simply elect to not log into them because we already have an
entry for the local loop. There is relatively unexercised code
just for this case.
MFC after: 2 weeks
1) Bite the bullet, and allow unaligned accesses without buffer copies
on the i386 platform. According to some tests run by Andrew Gallatin,
the buffer copy performance hit is greater than the unaligned access
performance hit (especially with jumbo frames). We still need to copy
everywhere else.
2) Enable interrupt moderation with a 100us timeout.
Submitted by: Andrew Gallatin <no longer at duke.edu>
MFC after: 1 week
- When both SC_PIXEL_MODE and SC_NO_FONT_LOADING are defined,
quietly drop SC_NO_FONT_LOADING, because the pixel(raster)
console requires font.
- When SC_NO_FONT_LOADING is defined, force SC_ALT_MOUSE_IMAGE.
Without font, the arrow-shaped mouse cursor cannot be drawn.
- Fiddle and simplify some internal macros.
MFC after: 2 weeks
haven't been probed successfully. It's a known bug that ISA hints
processing instantiates those devices, and prematurely killing them
has other unwanted side-effects.
where they will never succeed. Add a stop-gap measure that will at
least eventually timeout the operation instead of retrying it
indefinately.
MFC after: 1 month
Despite of a few cosmetic things like adding ``irritating silly
parentheses'' around all return values, this mainly improves FDC reset
handling by no longer gratuitously resetting the FDC all the time
(which causes it to lose the notion of the current track) but only in
case of errors, and it sanitizes the block and offset calculations in
fdstrategy() and fdstate(). Some additional cleanup added by me, in
particular the large switch in fdstate() now always uses return to
break out, and no branch falls off the end of the switch statement
anymore. Per Bruce's suggestion, removed M_NOWAIT from the malloc()s
to simplify things.
Submitted by: bde (mostly)
Previously, I had the MODE_1000 bit in the global config register set
unconditionally, which was wrong: we have to turn it off if we have
a 10/100 link. This is now handled in the nge_miibus_statchg() routine.
Discovered by: Nathan Binkert <binkertn@eecs.umich.edu>
(Note: this commit is being done from JFK airport. :P )
Monitor the system power profile, and use _SCP to adjust thermal zones
accordingly.
Simplify the behaviour of the timeout routine, and add some temporary
debugging.
PCI bus object. This should deal both with already-routed interrupts
as well as devices that need an interrupt routed.
Note that it *doesn't* deal with interlocked interrupt dependancies, nor
does it select between interrupt options in a smart way. These are
optimisations that need further work.
is a parallel adjunct to active cooling, not a lesser evil. The _ACx
levels sort from 0 being hottest, not coolest.
Sanity check the returned temperature values, since we are having
trouble reading them on some systems.
Rearrange sysctl nodes a bit; this is probably close to the final layout.
destroyed properly (otherwise bad things would happen after a clone
dev had been created, and the module was kldunloaded). Allocated
children that have not successfully probed are being deleted again
(otherwise fd0 and fd1 have always been allocated, even if only
fd0 was acutally present, and fd1 even survived kldunloading the
module).
Still, kldunloading leaves remnants of the previously existing devices
intact. Why doesn't it destroy all the devices? As a consequence,
since dev->descr now points into no longer allocated memory, the
system panics deep inside printf(9) when running devinfo(1) after
kldunloading the module. Ideas sought...
Also, when kldloading the module on a hints-populated isab0, this bus
somehow has already created an fdc0 entry (a dummy) so the load
attempt fails and will register fdc1 instead. What are those dummy
entries for? Loading the module from the bootloader works, and it
can be unloaded an re-loaded then later.
For fibre channel, start going for the gusto and using AC_FOUND_DEVICE
and AC_LOST_DEVICE calls to xpt_async when devices appear and disappear
as the loop or fabric changes.
ISPASYNC_FW_CRASH is the async event code where the platform layer
deals with a firmware crash.
some of the RIO (reduced interrupt operation) stuff. Add 64 bit
data list (DSD type 1) and arbitrary data list (DSD type 2)
data structure defines.
Add macros that parameterize usage of the Request/Response in/out
queue pointers. When we finish 2300 support, different registers
will be accessed for the 2300.
part of the PCI block for the 2300- not software convention usage
of the mailbox registers- so we macrosize in/out pointer usage.
Only report that a LIP destroyed commands if it actually destroyed
commands. Get the chan/tgt/lun order correct. Fix a longstanding
stupid bug that caused us to try and issue a command with a tag on
Channel B because we were checking the tagged capability for the
target against Channel A.
A firmware crash is now vectored out to platform specific code
as an async event.
Some minor formatting tweaks.
(this commit is just the first stage). Also add various GIANT_ macros to
formalize the removal of Giant, making it easy to test in a more piecemeal
fashion. These macros will allow us to test fine-grained locks to a degree
before removing Giant, and also after, and to remove Giant in a piecemeal
fashion via sysctl's on those subsystems which the authors believe can
operate without Giant.
- Move the lance_probe function to if_lnc.c.
- Support C-NET(98)S again.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata) and nyan
No response from: Paul Richards
* add support for mic record channel
* add support for setblocksize
* make mpsafe
* make getptr accurate
* reduce buffer size from 64k to 16k for better synchronisation
removed and a minimal number of changes to make it compile in the new
location.
# I have a fully converted on a disk that may be crashed. If it is
# crashed, I'll redo the work.
MFC after: 5 days
- Mask GPCNTL against 0x1c (was 0xfc) for the reading of the NVRAM.
This ensures LEDC bit will not be set on 896 and later chips.
Submitted by Chip Salzenberg <chip@perlsupport.com>.
- Add probe for Tekram 390 U2B/U2W SCSI (53C895) LED handling.
Submitted by Chip Salzenberg <chip@valinux.com>
Pass the softc, not the device_t to the Notify handler.
Don't invoke the Interpreter from callout context, as it may sleep.
Use AcpiOsQueueForExecution, which is called from taskqueue_swi.
Add an ACPI subsystem mutex, and macros for handling it. Because it's
not possible to differentiate between ACPI CA acquiring mutexes for
internal use and for use by AML, and because AML in the field doesn't
handle mutexes correctly, we can't use the ACPI subsystem's internal
locking. In addition, we have other private data of our own to lock.
Add initial locking to the ACPI driver code and the thermal module.
These locks are currently inoperative.
Pull some errant style back into line.
the sector ID.
Based on numerous comments made by Bruce, rewrite a good part of the
old fdformat() function, and merge it with fdreadid() into a single
unified fdmisccmd() function. Various style and a couple of more
serious bugs fixed there.
While i was at it, i also fixed the long-standing "TODO: don't
allocate buffer on stack." in fdcioctl(), fixed a number of style bugs
there, and finally implemented the FD_DEBUG ioctl command that has
been advertised in <sys/fdcio.h> (formerly <machine/ioctl_fd.h>) for
almost seven years now. ;-)
Submitted by: bde (a lot of fixes for fdformat())
a KLD. Still doesn't work well except in the PCMCIA case (now if only
pccardd(8) could load and unload drivers dynamically...). Mainly, it
tries to find fdc0 on the PCI bus for whatever obscure reasons, but i
need someone who understands driver(9) to fix this. However, it's at least
already better than before, and i'm tired of maintaining too many private
changes in my tree, given the large patches bde submitted. :)
Idea of a KLD triggered by: Michael Reifenberger <root@nihil.plaut.de>
by now (except of a compile test), but i believe this to contain no
actual functional changes.
. Fix the copyright of the Regents i accidentally broke in rev 1.197
(although only a very small part of the original driver survived
at all...).
. Bump MAX_CYLINDER since some obscure formats really use more than 80
cylinders.
. Correctly handle BIO_FORMAT which used to be a bitmask but is now a BIO
command of its own.
. Numerous stylistic fixes.
Submitted by: bde
- Reorder the acpi_* functions in a sensible fashion
- Add acpi_ForeachPackageObject and acpi_GetHandleInScope
- Use the new debugging layer/level names
- Implement most of the guts of the acpi_thermal module; passive cooling
isn't there yet, but active cooling should work.
- Implement power resource handling (acpi_powerres.c)
This compiles and mostly works, but my test coverage is small, so feedback
is welcome.
if a device has vchans already but they are all busy, allocate another one
at open() time, up to a maximum of hw.snd.maxvchans.
when creating/destroying vchans, don't make/remove a devnode for the
first/last one as it replaces a hardchan.
functions in ifconfig. "ifconfig an0" should output the correct
status now. Also, make the read and write functions both more
robust and more consistant. This should stop most of the incorrect
size complaints and eliminate the possiability of panics from firmware
that increases resource sizes.
PR: kern/27826
Reviewed by: imp, jlemon
Submitted by: Doug Ambrisko <ambrisko@ambrisko.com>
David Wolfskill <dhw@whistle.com>
. staticize out_fdc(), there's no longer an ft(4) driver sharing its use
. remove in_fdc(), has been used by ft(4) last time, long since obsoleted
by fd_in()
. move the declaration of fd_clone() to where most of the other function
declarations are
. de-__P()ify fd_clone(), it's been the only _P()ed function in the
entire file
something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
the console device was open. At other times, the interrupts that
are used to detect the break signal or ~^B sequence were disabled,
so these events would not be noticed until the next open (e.g. the
next kernel printf). This was mainly a problem while there was no
getty running on the console, such as during bootup or shutdown.
For serial consoles with break-to-debugger support, we now enable
the generation of interrupts at attach time, and we leave them
enabled while the device is closed.
Reviewed by: bde (I've since made chages as per his suggestions)
via the new DIGIIO_SETALTPIN ioctl, and allow the port's ALTPIN setting
to be queried via DIGIIO_GETALTPIN.
The initial state and lock devices are normally used to set and/or
lock ALTPIN settings although the device itself may also be used.
ALTPIN settings are applied per-device and apply to both the callin
and callout device at the same time.
converting from the old external mbuf buffer code to the new (with the
MEXTADD() macro). Also free free list memory correctly in
foo_free_jumbo_mem() routines: grab the head of the list, then
remove it, _then_ free() it.
This fixes the memory corruption problem I've been chasing in the level 1
driver.
1: most drivers are sensitive to timing, and
2: the handlers are MPSAFE and need a chance to get into the kernel
before some other non-mpsafe handler blocks the ithread on Giant in
shared irq cases.
Reviewed by: cg (in principle)
worked before.
mixer, dsp and sndstat are seperate devices - give them their own cdevsws
instead of demuxing requests sent to a single cdevsw.
use the si_drv1/si_drv2 fields in dev_t structures for holding information
specific to an open instance of mixer/dsp.
nuke /dev/{dsp,dspW,audio}[0-9]* links - this functionality is now provided
using cloning.
various locking fixes.
ports later on.
This includes the basic MI interface routines as well as a console driver.
The MD code is kept in the MD directories.
Reviewed by: obrien
built in, or as an addon card (My Japanese isn't quite good enough to
know which). [FreeBSD98-testers 5098] contains all the details.
Submitted by: Kawanobe Koh-san <kawanobe@st.rim.or.jp>
The DP83820/83821 has an undocumented limitation concerning jumbo frames
and TX checksum offload. In order for TX checksum offload to work, the
outgoing frame must fit entirely within the TX FIFO, which is 8192 bytes
in size. This isn't a problem, until you try to send a 9000-byte frame,
at which point the TX DMA engine goes to sleep. It turns out that if
you want to send a jumbo frame larger than 8170 bytes (8192 - 64), you
have to turn off the TX checksum support.
As a workaround, I changed nge_ioctl() so that if the user selects an
MTU larger than 8152 bytes, we clear the if_hwassist flags. The flags
will be set again once the MTU is reduced to a smaller value.
we want the checksums calculated on a per-packet basis using control bits
in the extsts field of the DMA descriptor structure. For TX, the chip
seems to want these bits set in the field of the first descriptor in
a fragment chain, not the last.
vinumhdr.h:80: warning: redundant redeclaration of `vinum_cdevsw'
vinumext.h:239: warning: previous declaration of `vinum_cdevsw'
in each of the following files:
vinum.c, vinumconfig.c, vinumdaemon.c, vinuminterrupt.c, vinumio.c,
vinumioctl.c, vinumlock.c, vinummemory.c, vinumraid5.c, vinumrequest.c,
vinumrevive.c, vinumstate.c, vinumutil.c
musycc.c:449: warning: long unsigned int format, unsigned int arg (arg 3)
musycc.c:449: warning: long unsigned int format, unsigned int arg (arg 4)
musycc.c:453: warning: long unsigned int format, unsigned int arg (arg 3)
musycc.c:453: warning: long unsigned int format, unsigned int arg (arg 4)
musycc.c:453: warning: long unsigned int format, unsigned int arg (arg 5)
These warnings used to be confined to the alpha but are on all now.
554: passing arg 4 of `resource_string_value' from incompatible pointer type
576: passing arg 4 of `resource_string_value' from incompatible pointer type
593: passing arg 4 of `resource_string_value' from incompatible pointer type
commands that complete (with no apparent error) after
we receive a LIP. This has been observed mostly on
Local Loop topologies. To be safe, let's just mark
all active commands as dead if we get a LIP and we're
on a private or public loop.
MFC after: 4 weeks
Replace the a.out emulation of 'struct linker_set' with something
a little more flexible. <sys/linker_set.h> now provides macros for
accessing elements and completely hides the implementation.
The linker_set.h macros have been on the back burner in various
forms since 1998 and has ideas and code from Mike Smith (SET_FOREACH()),
John Polstra (ELF clue) and myself (cleaned up API and the conversion
of the rest of the kernel to use it).
The macros declare a strongly typed set. They return elements with the
type that you declare the set with, rather than a generic void *.
For ELF, we use the magic ld symbols (__start_<setname> and
__stop_<setname>). Thanks to Richard Henderson <rth@redhat.com> for the
trick about how to force ld to provide them for kld's.
For a.out, we use the old linker_set struct.
NOTE: the item lists are no longer null terminated. This is why
the code impact is high in certain areas.
The runtime linker has a new method to find the linker set
boundaries depending on which backend format is in use.
linker sets are still module/kld unfriendly and should never be used
for anything that may be modular one day.
Reviewed by: eivind
- Replace some very poorly thought out API hacks that should have been
fixed a long while ago.
- Provide some much more flexible search functions (resource_find_*())
- Use strings for storage instead of an outgrowth of the rather
inconvenient temporary ioconf table from config(). We already had a
fallback to using strings before malloc/vm was running anyway.
. remove stale comments and a stale #define (from the old days of ft(4))
. make MAX_SEC_SIZE (used in isa_dmainit()) a #define
. fix a typo in a string
. use 0 as the blocksize in devstat_add_entry(), since the actual blocksize
is unknown (devstat(9) suggests to use 0 in that case)
around, use a common function for looking up and extracting the tunables
from the kernel environment. This saves duplicating the same function
over and over again. This way typically has an overhead of 8 bytes + the
path string, versus about 26 bytes + the path string.
use of the extsts field in DMA descriptors. We need this to tell the chip
to calculate TCP/IP checksums in hardware on a per-packet basis.
- Fix the unions in DMA descriptor structures. Breakage on alpha led
me to realize I'd done it wrong the first time.
that device add/remove will work without usbd running. usbd is still
used for execing stuff, but that is all now. Ideally it could be replaced
by a devd some day. Until now, usbd had to be running so that the
USB_DISCOVER ioctl could be called to walk the tree when an attachment
status change was noticed.
Among the changes:
- when a detach happens, remove any pending 'attach' messages or the system
suffers from whiplash from exec moused / kill moused loops if you do lots
of attach/detach and later start usbd.
- tweaks related to kthread differences
- disable the select handler for the old interface (never return success).
I have not removed it yet or old usbd's will abort. That can get removed
later once usbd is cleaned up and things have stabilized for a few weeks.
- get Giant in the kthread.
- a couple of minor potential bug fixes (usb_nevents vs malloc failure etc)
Pre-approved by: n_hibma (ages and ages ago)
ep driver. The rest of the patch will wait until I can put the time
into it to get it righter than the kludge it is.
This protects us against card eject problems at all times,e xecpt when
we're in the epintr ISR.
I think bde even reviewed it once.
Also, change the name of ActionTEC pat to more generic Lucent Kermit
chip. Add stub for Xircom card. Add cardbus attachment too.
compliant. All the variable definitions and function names are
reasonably consistent, and the functions which should be static (i.e.,
all of them) are. Other assorted fixes were made. The majority of
the delta is indentation fixes.
Partially reviewed by: bde
can be made userland-visible as <dev/ic/...>. Also, those files are
not supposed to contain any bus-specific details at all, so placing
them under .../isa/ has been a misnomer from the beginning.
The files in src/sys/dev/ic/ have been repo-copied from their old
location (this commit is a forced null commit there to record this
message).
The 3C509-TX card apparently had a slightly different version of the
chip, and has problems when this register is set. The problem does
not appear on the 3C509{BC} cards, but since only the fxp driver needs
specific bits set, conditionalize on that.
all alphas with devices behind ppb's. I'm working on a better solution now.
Note that all alphas that use per-platform interrupt mapping are broken
again (as they have been for several months)
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
this works on cs4630 chips, and should implement the clkrun hack for
thinkpads- this will display diagnostic messages when triggered until its
correctness is established.
