images into the kernel as currently included into iwn6000g2{a,b}fw.ko
and delete the old files, missed in r254199 and r259135 respectively.
MFC after: 3 days
These variants have a few differences from the default AR9485 NIC,
namely:
* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.
To make this possible:
* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.
This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.
Tested:
* AR9380 (STA)
* AR9485 CUS198 (STA)
Obtained from: Qualcomm Atheros, Linux ath9k
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
If powersave is enabled and there are any transitions to network
or full sleep - even if they're pretty damned brief - eventually
something messes up somewhere and the bus glue between the AR9331
SoC and the AR9331 wifi stops working. It shows up as stuck DMA
and LOCAL_TIMEOUT interrupts.
Both ath9k and the reference driver does a full chip reset if things
get stuck.
So:
* teach the AR9330 HAL about the force_full_reset option I added a
couple of years ago;
* if the chip is currently in full-sleep, do a full-reset;
* if TX DMA and/or RX DMA are still enabled (eg, they did get
stuck during reset) then do a full-reset.
Tested:
* AR9331 SoC, STA mode
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
This driver is based on Linux 3.8 and a previous effort by kan@.
More informations about this project can be found on the FreeBSD wiki:
https://wiki.freebsd.org/AMD_GPU
The driver is split into:
sys/dev/drm2:
The driver sources.
sys/modules/drm2/radeonkmw:
The driver main kernel module's Makefile.
sys/modules/drm2/radeonkmsfw:
All firmware kernel module Makefiles. There's one directory and one
Makefile for each firmware.
sys/contrib/dev/drm2/radeonkmsfw:
All firmware binary sources.
tools/tools/drm/radeon
Tools to update firmwares or regenerate some headers.
Merging the driver to FreeBSD 9.x may be possible but not a priority for
now.
Help from: kib@, kan@
Tested by: avg@, kwm@, ray@,
Alexander Yerenkow <yerenkow@gmail.com>,
Anders Bolt-Evensen <andersbo87@me.com>,
Denis Djubajlo <stdedjub@googlemail.com>,
J.R. Oldroyd <fbsd@opal.com>,
Mikaël Urankar <mikael.urankar@gmail.com>,
Pierre-Emmanuel Pédron <pepcitron@gmail.com>,
Sam Fourman Jr. <sfourman@gmail.com>,
Wade <wade-is-great@live.com>,
(probably other I forgot...)
HW donations: kyzh, Yakaz
When building AR933x test images, I'd like to only build only the ar9300
HAL. To do this, it needs to supply an RF linker entry or it won't compile.
Tested:
* AR933x test builds
NICs which have bluetooth coexistence enabled.
The WB225 NIC has the common antenna switch configuration set to 0x0 which
disables all external switch bit setting. This obviously won't work when
doing coexistence.
This value is a magic value from the windows .inf files. It _looks_ right
but I haven't yet verified it - unfortunately my AR9285+AR3012 BT combo
has an earlier BT device which doesn't actually _have_ firmware on it.
So I have to fix ath3kfw to handle loading in firmware into the newer
NICs before I can finish testing this.
This may not hold true for CUS198, which is another custom AR9485 board.
The bluetooth setup code actually does a channel lookup during setup,
even though we haven't yet programmed in a channel. Sigh.
Tested:
* WB225 (AR9485) + bluetooth
The QCA9565 is a 1x1 2.4GHz 11n chip with integrated on-chip bluetooth.
The AR9300 HAL already has support for this chip; it just wasn't
included in the probe/attach path.
Tested:
* This commit brought to you over a QCA9565 wifi connection from
FreeBSD.
* .. ie, basic STA, pings, no iperf or antenna diversity checking just yet.
work in FreeBSD.
This is still heavily a work in progress but I'd rather it start
shipping in -HEAD sooner rather than later.
This doesn't (yet) link it into the build system either for a static
kernel or as a module; that will come later (after many, many make universe
tests.)
Revert r233555 and apply a fix for the reference counting regressions.
Tested by: andreast, lme, nwhitehorn,
Sevan / Venture37 (venture37 at gmail dot com)
Submitted by: Robert Moore (robert dot moore at intel dot com)
Temporarily revert an upstream commit. This change caused regressions for
too many laptop users. Especially, automatic repair for broken _BIF caused
strange reference counting issues and kernal panics. This reverts:
c995fed15a
TRENDnet TEW-504UB/EU) idProduct didn't be decreased after loading the
firmware.
Pointed by: Steven Friedrich <freebsd at insightbb.com>
Reviewed by: sam
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
o new tx ack queue (not used right now)
o proxy-sta related changes (no proxy sta in driver)
o explicit dwds ena/dis (needed only with proxy sta)
o cleanup BA policy handling
o new ampdu aggressive mode support
o CFEnd use now controllable
Approved by: re (kensmith)
- Define ACPI_USE_DO_WHILE_0 to add do while(0) around return_*() macros.
- Define __cdecl only for user land. It will never be used in kernel.
- Remove __cli() and __sti(). They were deprecated long ago.
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
current@ and stable@ for the locking patches. The driver can always be
revived if someone tests it.
This driver also sleeps in its if_init routine, so it likely doesn't really
work at all anyway in modern releases.
- Add a mutex to the softc and use it to protect the softc and device
hardware.
- Setup interrupt handler after interface attach.
- Retire 'unit' from softc and use if_printf() instead.
- Don't frob IFF_UP in the driver.
- Use callout_() rather than timeout() and untimeout().
