This dramatically improves RX sensitivity and behaviour on the
AR9331 hardware I have, including the Carambola 2.
Tested:
* AR9331, Carambola 2 board
Submitted by: Zilvinas Valinskas <zilvinas.valinskas@gmail.com>
This is used by the 'athsurvey' command to print out channel survey
statistics - % busy times transmit, receive and airtime.
It's as buggy and incomplete as the rest of the HAL survey support -
notably, tying into the ANI code to read channel stats and occasionally
getting garbage counters isn't very nice. It also doesn't (yet!) get
channel survey information during a scan. But it's good enough for
basic air-time debugging, which is why I'm committing it in this state.
Tested:
* AR9380, STA mode
path.
* For now there's no exposed control over classic / LNA antenna diversity,
so just stub them out. Adding this will take quite a bit of time.
* Add a function to fetch the CTS timeout.
PR: kern/198558
I don't like having it in this function; I may migrate it to ar9300_freebsd.c
at some point to keep the HAL code pollution down.
This allows ANI to be disabled via a sysctl.
Tested:
* AR9331, STA/TDMA modes
This is a custom FreeBSD HAL method that is used by the TDMA code
to program the beacon timers directly without any guesswork/assumptions
by the HAL.
This brings up basic TDMA master/slave support on the AR9380 HAL,
however there are other issues preventing it from being stable.
(I'm seeing beacon interval instability, which may be due to
busy 2GHz air, but also may be due to some HAL configuration
issues with regards to ANI, or hardware timer programming, etc.)
Tested:
* AR9331 (Carambola2), STA, AP, adhoc and TDMA master mode.
The QCA9565 can have RFKILL on GPIO Pin 11, and thus we need to configure
it up correctly or the NIC may not function.
I'm not sure why the AR9382 can't use GPIO 8 / GPIO 11 ; it's likely
hooked up to some external LNA or filter. The real solution is to
make it only block pin 8 / pin 11 for AR9382, but the AR9382 probes
like an AR9380. Sigh.
Submitted by: Anthony Jenkins <scoobi_doo@yahoo.com>
I've been sitting on this for a year or so now; I've finally
tested it on enough devices to be reasonably sure it won't
cause too much drama. But, if you see issues, please email me.
Tested (all STA mode):
PCIe:
* AR9380
* AR9390
* AR9580
* AR9462
* AR9485
SoC:
* QCA9550
* AR9331
* AR9342
hw.x2apic_enable tunable allows disabling it from the loader prompt.
To closely repeat effects of the uncached memory ops when accessing
registers in the xAPIC mode, the x2APIC writes to MSRs are preceeded
by mfence, except for the EOI notifications. This is probably too
strict, only ICR writes to send IPI require serialization to ensure
that other CPUs see the previous actions when IPI is delivered. This
may be changed later.
In vmm justreturn IPI handler, call doreti_iret instead of doing iretd
inline, to handle corner conditions.
Note that the patch only switches LAPICs into x2APIC mode. It does not
enables FreeBSD to support > 255 CPUs, which requires parsing x2APIC
MADT entries and doing interrupts remapping, but is the required step
on the way.
Reviewed by: neel
Tested by: pho (real hardware), neel (on bhyve)
Discussed with: jhb, grehan
Sponsored by: The FreeBSD Foundation
MFC after: 2 months
the ia_array field of struct ar9300_ini_array const, and removing the
const-dropping casts. No functional change.
Reviewed by: adrian
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D1725
AR9462/AR9565.
This and some upcoming changes to the HAL for these chips should
address some of the signal sensitivity reported by users.
Tested:
* AR9462 (WB222), STA mode
Obtained from: Linux ath9k
AR9565 (Aphrodite.) These need to use the MCI routines, not
the legacy 2-wire / 3-wire bluetooth coexistence methods.
Tested:
* AR9462 (WB222); STA mode
images into the kernel as currently included into iwn6000g2{a,b}fw.ko
and delete the old files, missed in r254199 and r259135 respectively.
MFC after: 3 days
These variants have a few differences from the default AR9485 NIC,
namely:
* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.
To make this possible:
* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.
This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.
Tested:
* AR9380 (STA)
* AR9485 CUS198 (STA)
Obtained from: Qualcomm Atheros, Linux ath9k
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
If powersave is enabled and there are any transitions to network
or full sleep - even if they're pretty damned brief - eventually
something messes up somewhere and the bus glue between the AR9331
SoC and the AR9331 wifi stops working. It shows up as stuck DMA
and LOCAL_TIMEOUT interrupts.
Both ath9k and the reference driver does a full chip reset if things
get stuck.
So:
* teach the AR9330 HAL about the force_full_reset option I added a
couple of years ago;
* if the chip is currently in full-sleep, do a full-reset;
* if TX DMA and/or RX DMA are still enabled (eg, they did get
stuck during reset) then do a full-reset.
Tested:
* AR9331 SoC, STA mode
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
This driver is based on Linux 3.8 and a previous effort by kan@.
More informations about this project can be found on the FreeBSD wiki:
https://wiki.freebsd.org/AMD_GPU
The driver is split into:
sys/dev/drm2:
The driver sources.
sys/modules/drm2/radeonkmw:
The driver main kernel module's Makefile.
sys/modules/drm2/radeonkmsfw:
All firmware kernel module Makefiles. There's one directory and one
Makefile for each firmware.
sys/contrib/dev/drm2/radeonkmsfw:
All firmware binary sources.
tools/tools/drm/radeon
Tools to update firmwares or regenerate some headers.
Merging the driver to FreeBSD 9.x may be possible but not a priority for
now.
Help from: kib@, kan@
Tested by: avg@, kwm@, ray@,
Alexander Yerenkow <yerenkow@gmail.com>,
Anders Bolt-Evensen <andersbo87@me.com>,
Denis Djubajlo <stdedjub@googlemail.com>,
J.R. Oldroyd <fbsd@opal.com>,
Mikaël Urankar <mikael.urankar@gmail.com>,
Pierre-Emmanuel Pédron <pepcitron@gmail.com>,
Sam Fourman Jr. <sfourman@gmail.com>,
Wade <wade-is-great@live.com>,
(probably other I forgot...)
HW donations: kyzh, Yakaz
When building AR933x test images, I'd like to only build only the ar9300
HAL. To do this, it needs to supply an RF linker entry or it won't compile.
Tested:
* AR933x test builds
NICs which have bluetooth coexistence enabled.
The WB225 NIC has the common antenna switch configuration set to 0x0 which
disables all external switch bit setting. This obviously won't work when
doing coexistence.
This value is a magic value from the windows .inf files. It _looks_ right
but I haven't yet verified it - unfortunately my AR9285+AR3012 BT combo
has an earlier BT device which doesn't actually _have_ firmware on it.
So I have to fix ath3kfw to handle loading in firmware into the newer
NICs before I can finish testing this.
This may not hold true for CUS198, which is another custom AR9485 board.
The bluetooth setup code actually does a channel lookup during setup,
even though we haven't yet programmed in a channel. Sigh.
Tested:
* WB225 (AR9485) + bluetooth
The QCA9565 is a 1x1 2.4GHz 11n chip with integrated on-chip bluetooth.
The AR9300 HAL already has support for this chip; it just wasn't
included in the probe/attach path.
Tested:
* This commit brought to you over a QCA9565 wifi connection from
FreeBSD.
* .. ie, basic STA, pings, no iperf or antenna diversity checking just yet.
work in FreeBSD.
This is still heavily a work in progress but I'd rather it start
shipping in -HEAD sooner rather than later.
This doesn't (yet) link it into the build system either for a static
kernel or as a module; that will come later (after many, many make universe
tests.)
Revert r233555 and apply a fix for the reference counting regressions.
Tested by: andreast, lme, nwhitehorn,
Sevan / Venture37 (venture37 at gmail dot com)
Submitted by: Robert Moore (robert dot moore at intel dot com)
Temporarily revert an upstream commit. This change caused regressions for
too many laptop users. Especially, automatic repair for broken _BIF caused
strange reference counting issues and kernal panics. This reverts:
c995fed15a
TRENDnet TEW-504UB/EU) idProduct didn't be decreased after loading the
firmware.
Pointed by: Steven Friedrich <freebsd at insightbb.com>
Reviewed by: sam
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
o new tx ack queue (not used right now)
o proxy-sta related changes (no proxy sta in driver)
o explicit dwds ena/dis (needed only with proxy sta)
o cleanup BA policy handling
o new ampdu aggressive mode support
o CFEnd use now controllable
Approved by: re (kensmith)
- Define ACPI_USE_DO_WHILE_0 to add do while(0) around return_*() macros.
- Define __cdecl only for user land. It will never be used in kernel.
- Remove __cli() and __sti(). They were deprecated long ago.
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
current@ and stable@ for the locking patches. The driver can always be
revived if someone tests it.
This driver also sleeps in its if_init routine, so it likely doesn't really
work at all anyway in modern releases.
- Add a mutex to the softc and use it to protect the softc and device
hardware.
- Setup interrupt handler after interface attach.
- Retire 'unit' from softc and use if_printf() instead.
- Don't frob IFF_UP in the driver.
- Use callout_() rather than timeout() and untimeout().
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
This patch was part of ACPI-CA 20070508 release and the
following is excerpt from its change log:
Fixed a problem where the Global Lock handle was not properly
updated if a thread that acquired the Global Lock via executing
AML code then attempted to acquire the lock via the
AcpiAcquireGlobalLock interface. Reported by Joe Liu.
Approved by: re (kensmith)
Tested by: ambrisko
Obtained from: Intel
uuencoded format along with their respective LICENSE files.
- Add new share/doc/legal directory to BSD.usr.dist mtree file. This is the
place we install LICENSE files for restricted firmwares.
- Teach firmware(9) and kmod.mk about licensed firmwares. Restricted firmwares
won't load properly unless legal.<name>.license_ack is set to 1, either
via kenv(1) or /boot/loader.conf.
Reviewed by: mlaier, sam
Permitted by: Intel (via Andrew Wilson)
MFC after: 1 month
o remove os-specific glue code; it's now the responsibility of
the driver
o add wackelf utility for patching the ELF magic number on arm
builds since noone can agree on how to mark a .o file as not
having any floating point instructions
o remove radar/dfs-related entry points; folks have finally
decided how to support dfs w/o polluting the hal
o properly recognize AR2424 chips (they were being rejected on
attach despite being fully supported)
o add HAL_CAP_RXORN_FATAL capability to control how RXORN errors
are handled; previously RXORN was always treated as fatal because
older chips required a reset; now we do not treat it as fatal
for "newer chips" (noone seems to know what the cutoff is so
this capability can be used to override the current guestimate)
o HAL_CAP_RXTSTAMP_PREC capability to export the number of bits
of precision for timestamp data returned in the rx descriptor
o remove public exposure of the compression buffer; it is chip
specific and never belonged in the public view
o change definition of HAL_INT_GLOBAL from an enum member to a
#define to workaround compilers that bitch about enum values
that appear overflow 31 bits
o add support for newer chips that can store the tkip mic key
together with the cipher key in a single key cache entry
o split tx/rx descriptor into a h/w section and a s/w portion;
this permits storing the s/w area in cached memory when the
h/w area is stored in uncached memory; this also shrinks
memory use since only one status block is needed while multiple
tx/rx descriptors may be required per frame
o add final transmit series index to the transmit descriptor status
so rate control algorithms don't need to grovel through h/w state
to find it
o remove ds_vdata field from the descriptor state as part of the
radar changes
o fix excessive stack usage for some 5212 rf backends
o correct rfkill handling when the pin polarity is 0 true
o correct handling of tsf wrap when reading 64-bit values
MFC after: 1 month
