The buggy code was using the rxq index but should use the evq label
associated with the rxq. It was missed in r298735.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D6661
discovery without attaching to the targets ("iscsictl -Ad ... -e off"),
and then attach to selected ones ("iscsictl -Mi ... -e on").
PR: 204129
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6633
this to be the case. This will mean we don't try and handle the cache in
bus_dmamap_sync when it is not needed.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6605
- Avoid unnecessary indirection.
- Avoid bit fields.
- Use __packed.
Reviewed by: Jun Su <junsu microsoft com>
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6636
The legacy bits are just from ah.h; the MCI bits are from the ar9300
HAL "freebsd" extras.
A subsequent commit will include ah_btcoex.h into ah.h and remove
the older defintions.
While I'm here, prefix function names w/ vmbus, since unlike Hyper-V
timecounter, Hyper-V event timer will not work w/o vmbus.
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6598
Some machine BIOSes use the I2C bus and leave it in a state that causes
interrupts to not work properly due to a pending interrupt having been
latched.
Refactor the code a bit to clear pending interrupts when I2C is enabled.
This fixes the primary problem.
Also fix a possible race condition in the interrupt handler where the
interrupt was being cleared after reading the status instead of before.
Reported by: pfg
Reviewed by: jhb
Approved by: jhb
Obtained from: DragonFly BSD
Differential Revision: https://reviews.freebsd.org/D6586
While I'm here remove the event timer's dependency on hv_vmbus_priv.h
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6574
- Make sure that STIMER0 is disabled before writting to it, since
writing to an enabled STIMER will result in undefined behaviour.
- It is unnecessary to reconfigure STIMER0 upon each et_start().
- Make sure that MSR_HV_REF_TIME_COUNT will not return 0, since
writing 0 to STIMER_COUNT will disable the target STIMER.
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6573
When hwpmc stops sampling it will set the pm_state to something other
than PMC_STATE_RUNNING. This means the following sequence can happen:
CPU 0: Enter the interrupt handler
CPU 0: Set the thread TDP_CALLCHAIN pflag
CPU 1: Stop sampling
CPU 0: Call pmc_process_samples, sampling is stopped so clears ps_nsamples
CPU 0: Finishes interrupt processing with the TDP_CALLCHAIN flag set
CPU 0: Call pmc_capture_user_callchain to capture the user call chain
CPU 0: Find all the pmc sample are free so no call chains need to be captured
CPU 0: KASSERT because of this
This fixes the issue by checking if any of the samples have been stopped
and including this in te KASSERT.
PR: 204273
Reviewed by: bz, gnn
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6581
This is like the WB222 coexistence (ie, "MCI", a message bus inside the
chip), and it's currently a cut/paste so I can start using it to flesh
out the differences with WB222.
It doesn't completely /do/ bluetooth coexistence, because it turns out
I need to add some contigmalloc'ed buffers to the btcoex path for this
type of hardware. I'm putting this work in the "people would like
to see functioning-ish btcoex before FreeBSD-11" bucket because I see
this as "broken".
Tested:
* QCA9535 (WB335) NIC, BT + 2GHz STA
avoid panicking debug kernels.
t4_tom does not keep track of a connection once it switches to ULP mode
iWARP. If the connection falls out of ULP mode the driver/hardware seq#
etc. are out of sync. A better fix would be to figure out what the
current seq# are, update the driver's state, and perform all sanity
checks as usual.
This also prevents tracing to a P_INEXEC process since it could race
with other processes attaching to it in filemon_event_process_exec() due
to the filemon_get_proc() race of incrementing ref and then locking the
filemon. With the no-P_INEXEC invariant in place the p_filemon may only
be the same or NULL when trying to drop it in
filemon_event_process_exec().
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D6545
If the parent is DEAD or connect_request_upcall() fails, the parent
mutex is left locked. This leads to a hang when process_mpa_request()
is called again for another child of the listening endpoint.
Submitted by: Krishnamraju Eraparaju @ Chelsio
Obtained from: upstream iw_cxgb4
Sponsored by: Chelsio Communications
wrap the implementation so that it returns an error if INTRNG support is
not available. It should be possible to write a non-INTRNG implementation
of this function some day. In the meantime, there is code that contains
calls to this function (so the decl is needed), but have runtime checks to
avoid calling it in the non-INTRNG case.
Use for forever loop instead of while.
Found by lint on illumos.
Submitted by: Garrett D'Amore <garrett at damore.org>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
if_iwm - GC some dead code, left by a partially applied OpenBSD change.
Taken-From: OpenBSD (if_iwm.c r1.69)
Submitted by: Imre Vadasz <imre@vdsz.com>
Obtained from: DragonflyBSD git 07dfed32ea39b980b0b80d27ff938e7c3ca4c0b5
This will be more accurate as the actual name is provided if ran
from an absolute path in do_execve().
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
Pressing the PEK (power enable key) will shutdown the board.
Some events are reported to devd via system "PMU" and subsystem
"Battery", "AC" and "USB" such as connected/disconnected.
Some sensors values (power source voltage/current) are reported via
sysctl (dev.axp209_pmu.X.)
It also expose a gpioc node usable in kernel and userland. Only 3 of
the 4 GPIO are exposed (The GPIO3 is different and mostly unused on
boards). Most popular boards uses GPIO1 as a sense pin for OTG power.
Add a dtsi file that adds gpio-controller capability to the device as
upstream doesn't defined it and include it in our custom DTS.
Reviewed by: jmcneill
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6135
- Use device's channel list instead of default one (adds 12, 13 and 14
2GHz channels).
- Add ic_getradiocaps() method.
Differential Revision: https://reviews.freebsd.org/D6171
- Use device's channel list instead of default one (+ 12, 13 and 14
2GHz channels).
- Add ic_getradiocaps() method.
Differential Revision: https://reviews.freebsd.org/D6170
- Use device's channel list instead of default one (from
ieee80211_init_channels()).
- Add ic_getradiocaps() method.
Differential Revision: https://reviews.freebsd.org/D6144
- Use macros to define rate indices; don't hardcode them in code.
- Add method for 'rate' -> 'rate index' conversion
(and array for the opposite).
- Determine if rate is CCK / OFDM via appropriate macro.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D4837
Previously the USB PHY driver would enable all regulators at attach time.
This prevented boards from booting when powered by the USB OTG port, as
it didn't take VBUS presence into consideration.
in ICL interface.
- the ordering of parameters to icl_conn_task_setup is different, so that
the "cookie" is last.
- the icl_conn_connected() method is gone, replaced by much simpler mechanism.
I'd rather keep the ICL interface as small as possible.
- I don't really like the s/offload/driver/g. The "tcp" is not a driver;
"iser" is not really a driver either. I'd prefer to leave it as it is.
- the check for ic_session_type_discovery() in iser_conn_handoff() is gone,
as handoff cannot happen for discovery sessions.
- ic_session_login_phase() and ic_session_type_discovery() are gone. If you
had your handoff method called - you're no longer in either of those.
- the way maxtags is passed is different; now it's simply ic->ic_maxtags.
It's cleaner, and the old way would cause weird things to happen if
fail_on_disconnection=1 and the user changed the maxtags sysctl before
reconnecting (basically the CAM idea of maxtags would be different from
iSER one).
- icl_hba_misc() is gone; declare support for PIM_UNMAPPED by setting
ic->ic_unmapped flag.
- the way we find the "iser" ICL module is rewritten - we have a flag
for icl_register() that says if the module is iSER-capable or not.
- icl_conn_release() is gone; iser_conn_release() is called from
iser_conn_free() (no functional change in this case) and at the beginning
of icl_conn_connect(), to handle reconnection.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
written by Sagi Grimberg <sagig at mellanox.com> and Max Gurtovoy
<maxg at mellanox.com>.
This code comes from https://github.com/sagigrimberg/iser-freebsd, branch
iser-rebase-11-current-r291993. It's not connected to the build just yet;
it still needs some tweaks to adapt to my changes to iSCSI infrastructure.
Big thanks to Mellanox for their support for FreeBSD!
Obtained from: Mellanox Technologies
MFC after: 1 month
Relnotes: yes
This is a simple ioctl and mmap API to issue SPI transactions from
userland. It's useful for simple devices (eg spi temperature sensors,
etc) for experimentation.
TODO:
* Write some documentation!
Submitted by: green
This was triggering a panic on detach; the SPROM shadow is now
maintained by the bhnd_sprom_chipc driver, and should be removed
from chipc.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6548
This adds support for automatically configuring bhnd_chipc bus children
with associated resources, using an internal 'hints' table based directly
on Michael Zhilin's chipc resource mapping work.
The bhnd_sprom_chipc driver has been converted to use DEVICE_IDENTIFY()
with the new resource table.
This should be nearly drop-in compatible with the child device drivers
in D6250.
Submitted by: Landon Fuller <landonf@landonf.org>
Reviewed by: Michael Zhilin <mizhka@gmail.com>
Differential Revision: https://reviews.freebsd.org/D6525
tunable SYSCTL's. Linux module parameters are associated with the
module they belong to. FreeBSD does not share this concept of a parent
module. Instead add macros which define the prefix to use for the
module parameters in the LinuxKPI consumers.
While at it convert all "bool" LinuxKPI module parameters to "byte"
type, because we don't have a "bool" type of SYSCTL in FreeBSD.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Currently all radiotap structures in ral(4) are packed, but are not
aligned, which causes ral based devices to crash when one does
'ifconfig wlan0 up' for a wlan interface with a ral wlandev on arches
that care about structure alignment (e.g., MIPS).
Adding an aligned attribute helps fix this problem and ral devices
can be properly brought up.
Reviewed by: adrian
Sponsored by: Smartcom - Bulgaria AD
And release IDT vector before releasing ISR resources on interrupt
teardown path. We still have some work to do on the interrupt tearing
down path.
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6519
Though it is highly unlikely this function would fail w/ BUS_DMA_WAITOK,
we had better to check its return value; better safe then sorry here.
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6518
This was found while reworking the device tree nodes for dtsec to match the
Linux device tree. Instead of waiting and expecting later code to call
dpaa_portal_map_registers(), do the equivalent immediately upon mapping.
Otherwise, it's possible to access the pages before that function is called, and
hang the CPU.
This unifies handling of core, chip, and board-level device
matching, and adds support for matching device drivers
against the bus attach type (e.g. SoC vs WiFi adapter).
Core-level quirks on Broadcom's chipsets generally are specific
to some combination of chip model, core revision, chip
package (e.g. 12x9 SMT package), SROM revision, etc.
Unifying the match APIs for all three attribute types (core, chip,
board/srom) allows defining a single device quirk table that
matches across all of those attributes.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6515
than sc->areq. This is a bounds check to ensure we're not just cramming
arbitrarily sized nonsense into the driver and overflowing the heap.
PR: 209545
Submitted by: cturt@hardenedbsd.org
MFC after: 2 weeks
Option EFSYS_OPT_ALLOW_UNCONFIGURED_NIC disables check that the adapter
MAC address is not a local address (beginning 02).
Submitted by: Laurence Evans <levans at solarflare.com>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6508
And
- Move message and event flags to vmbus_softc per-cpu data.
- Get rid of hv_setup_arg, which serves no purpose now.
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6502
* convert phy_getinfo() to take a "gmode" flag, rather than the siba
TGSHIGH flags and then check for 2GHz. This should ensure that
gmode is set correctly even on DUALPHY NICs.
* move the siba_powerup() call and the TGSHIGH decoding into a
call to bwn_is_bus_siba(), and return an error if it's called
on anything else. We don't yet do anything else, but when we do..
Tested:
* BCM4322, 11a STA
This is all for the bhnd(4) work in progress. It's enough to probe/attach
all the bhnd internals, but we're missing OTP support and some cleanup
code. And, well, all the rest of the bhnd(4) migration.
So no, this won't give you BCM43225 support. Sorry!
This patchset adds support to bhnd_chipc for sharing SYS_RES_MEMORY
resources with its children, allowing us to hang devices off of
bhnd_chipc that rely on access to a subset of the device register space
that bhnd_chipc itself must also allocate.
We could avoid most of this heavy lifting if RF_SHAREABLE+SYS_RES_MEMORY
wasn't limited to use with allocations at the same size/offset.
As a work-around, I implemented something similar to vga_pci.c, which
implements similar reference counting of of PCI BAR resources for its
children.
With these changes, chipc will use reference counting of SYS_RES_MEMORY
allocation/activation requests, to decide when to allocate/activate/
deactivate/release resources from the parent bhnd(4) bus.
The requesting child device is allocated a new resource from chipc's
rman, pointing to (possibly a subregion of) the refcounted bhnd resources
allocated by chipc.
Other resource types are just passed directly to the parent bhnd bus;
RF_SHAREABLE works just fine with IRQs.
I also lifted the SPROM device code out into a common driver, since this
now allows me to hang simple subclasses off of a common driver off of both
bhndb_pci and bhnd_chipc.
Tested:
* (landonf) Tested against BCM4331 and BCM4312, confirmed that SPROM still
attaches and can be queried.
Submitted by: Landon Fuller <landonf@landonf.org>
Reviewed by: mizkha@gmail.com
Differential Revision: https://reviews.freebsd.org/D6471
The EFSYS_PREEMPT_DISABLE() and EFSYS_PREEMPT_ENABLE() macros
were used to ensure correct timing of I2C operations. The APIs
for I2C operations have been removed, so these macros have no
callers.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
It does not belong to the vmbus.
While I'm here rework the Hypercall setup, e.g. use busdma(9)
and avoid bit fields.
Discussed with: Jun Su <junsu microsoft com>
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6445
The variable "size" stores number of words (4bytes). But the loop over
memory uses size as number of bytes to scan memory. As result it fetches
only 1/4th of memory.
This patch solves this problem and nvram2env fetches all NVRAM variables.
Test plan:
Pre-requisites: any MIPS board with ASCII-based NVRAM mapped into memory
* Add "device nvram2env" into kernel configuration
* Specify hints: base is mandatory (according to nvram2env(4))
hint.nvram.0.base=0x1c7f8000 (it's valid address for Asus RT-N53 with
flags = 0x4)
* Build & load kernel with bootverbose
Actual result: only part of nvram variables are found
Expected result: all variables are found
Submitted by: Michael Zhilin <mizhka@gmail.com>
Differential Revision: https://reviews.freebsd.org/D6466
This adds a BHND_BUS_GET_ATTACH_TYPE(); the primary use-case is to let
chipc make a coarse-grained determination as to whether UART, SPI, etc
drivers ought to be attached, and on fullmac devices, whether a real
CPU driver ought to be skipped for the ARM core, etc.
Tested:
* BCM4331 (BHND)
* BCM4312 (SIBA)
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6492
Override global retry limit (which is set in R92C_RL) via per-frame
TX descriptor field. Obsoletes D3840 (should work better with 2+ vaps).
Tested with RTL8188EU and RTL8192CUS in STA mode (maxretry = [3-9]).
After r285994, sysctl(8) was fixed to use 273.15 instead of 273.20 as 0C
reference and as result, the temperature read in sysctl(8) now exibits a
+0.1C difference.
This commit fix the kernel references to match the reference value used in
sysctl(8) after r285994.
Sponsored by: Rubicon Communications (Netgate)
The GPIO hardware should not be owned by a single device, this defeats any
chance of use of the GPIO controller as an interrupt source.
ow(4) is now the only consumer of this 'feature' before we can remove it
for good.
Discussed with: ian, bsdimp
Fix panics which were present when BGX and PF module were unloaded.
Reviewed by: zbb
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D6346
Add directory structure and fix dependencies to be able to
build and use Cavium VNIC driver as a module.
Reviewed by: zbb
Obtained from: Semihalf
Sponsored by: Cavium
Differential Revision: https://reviews.freebsd.org/D6345
utilizing previously unused arg field of struct ccb_notify_acknowledge.
This makes new QUERY TASK, QUERY TASK SET and QUERY ASYNC EVENT requests
really functional for CAM target mode drivers.
tested on the Pass 1.1 and 2.0 ThunderX machines in the Netperf cluster.
Reviewed by: jhb
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6453
Store the last doorbell write in the mlx5e_sq structure and write the
doorbell to the hardware when the transmit routine finishes
transmitting all queued mbufs.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
This patch implements a sysctl which allows setting a factor, N, for
how many work queue elements can be generated before requiring a
completion event. When a completion event happens the code simulates N
completion events instead of only one. When draining a transmit queue,
N-1 NOPs are transmitted at most, to force generation of the final
completion event. Further a timer is running every HZ ticks to flush
any remaining data off the transmit queue when the tx_completion_fact
> 1.
The goal of this feature is to reduce the PCI bandwidth needed when
transmitting data.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
Also check the return value of copyin(9) to prevent unnecessary allocation in the failure case.
Submitted by: ngie
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5155
This patch introduces support of BHND on SoC: nexus-to-bhnd drivers.
bhnd_soc is attached under nexus and responsible for all BHND-style calls
from bhnd(4) bus to parents.
bcma_nexus is bhnd(4) bus, attached to bhnd_soc and implement all
nexus-style behaviour of BHND.
Submitted by: Michael Zhilin <mizhka@gmail.com>
Reviewed by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6248
Adds support for adjusting active bus resource allocations, limiting the
range to the constraints of the register window within which the resource
is mapped.
This is the final set of bhnd changes required to support delegating
ChipCommon's register space to child devices.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6470
This adds bhnd-compatible implementations of bus_(read|write|set)_(1|2|4) APIs,
and upgrades the SPROM parsing code to use bhnd_bus_read_region_stream_2().
This a precursor to bridge support for resource adjustment and the new
ChipCommon bus support.
Tested:
* Tested against BCM4331
* Kernel build verified via tinderbox.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6469
- Add a pcib_detach() function for the PCI-PCI bridge driver. It
tears down the NEW_PCIB and hotplug state including destroying
resource managers, deleting child devices, and disabling hotplug
events.
- Add a detach method to the ACPI PCI-PCI bridge driver which calls
pcib_detach() and then frees the copy of the _PRT interrupt routing
table.
- Add a detach method to the PCI-Cardbus bridge driver which frees
the PCI bus resources in addition to calling cbb_detach().
- Explicitly clear any pending hotplug events during attach to ensure
future events will generate an interrupt.
- If a the Command Completed bit is set in the slot status register
when the command completion timeout fires, treat it as if the
command completed and the completion interrupt was just lost rather
than forcing a detach.
- Don't wait for a Command Completed notification if Command Completion
interrupts are disabled. The spec explicitly says no interrupt is
enabled when clearing CCIE, and on my T400 no interrupt is generated
when CCIE is changed from cleared to set, either. In addition, the
T400 doesn't appear to set the Command Completed bit in the cases
where it doesn't generate an interrupt, so don't schedule the timer
either. (If the CC bit were always set, one could always set the timer
and rely on the logic of treating CC set as a missed interrupt.)
Reviewed by: imp (older version)
Differential Revision: https://reviews.freebsd.org/D6424
Split getchannels() method in ath_hal/ah_regdomain.c into a subset
of functions for better readability.
Note: due to different internal structure, it cannot use
ieee80211_add_channel*() (however, some parts are done in a
similar manner).
Differential Revision: https://reviews.freebsd.org/D6139
This code was originally implemented 7 years ago, but never really worked
due to trivial error. I think this functionality may be not required.
Initiators supporting optional periodic command status checks detected
those terminated commands and retried them 3 seconds later. But thinking
about less featured initiators and the fact that it is our race makes
virtual ports "unknown" it may be good to have this feature.
This change includes support for SCSI SMR drives (which conform to the
Zoned Block Commands or ZBC spec) and ATA SMR drives (which conform to
the Zoned ATA Command Set or ZAC spec) behind SAS expanders.
This includes full management support through the GEOM BIO interface, and
through a new userland utility, zonectl(8), and through camcontrol(8).
This is now ready for filesystems to use to detect and manage zoned drives.
(There is no work in progress that I know of to use this for ZFS or UFS, if
anyone is interested, let me know and I may have some suggestions.)
Also, improve ATA command passthrough and dispatch support, both via ATA
and ATA passthrough over SCSI.
Also, add support to camcontrol(8) for the ATA Extended Power Conditions
feature set. You can now manage ATA device power states, and set various
idle time thresholds for a drive to enter lower power states.
Note that this change cannot be MFCed in full, because it depends on
changes to the struct bio API that break compatilibity. In order to
avoid breaking the stable API, only changes that don't touch or depend on
the struct bio changes can be merged. For example, the camcontrol(8)
changes don't depend on the new bio API, but zonectl(8) and the probe
changes to the da(4) and ada(4) drivers do depend on it.
Also note that the SMR changes have not yet been tested with an actual
SCSI ZBC device, or a SCSI to ATA translation layer (SAT) that supports
ZBC to ZAC translation. I have not yet gotten a suitable drive or SAT
layer, so any testing help would be appreciated. These changes have been
tested with Seagate Host Aware SATA drives attached to both SAS and SATA
controllers. Also, I do not have any SATA Host Managed devices, and I
suspect that it may take additional (hopefully minor) changes to support
them.
Thanks to Seagate for supplying the test hardware and answering questions.
sbin/camcontrol/Makefile:
Add epc.c and zone.c.
sbin/camcontrol/camcontrol.8:
Document the zone and epc subcommands.
sbin/camcontrol/camcontrol.c:
Add the zone and epc subcommands.
Add auxiliary register support to build_ata_cmd(). Make sure to
set the CAM_ATAIO_NEEDRESULT, CAM_ATAIO_DMA, and CAM_ATAIO_FPDMA
flags as appropriate for ATA commands.
Add a new get_ata_status() function to parse ATA result from SCSI
sense descriptors (for ATA passthrough over SCSI) and ATA I/O
requests.
sbin/camcontrol/camcontrol.h:
Update the build_ata_cmd() prototype
Add get_ata_status(), zone(), and epc().
sbin/camcontrol/epc.c:
Support for ATA Extended Power Conditions features. This includes
support for all features documented in the ACS-4 Revision 12
specification from t13.org (dated February 18, 2016).
The EPC feature set allows putting a drive into a power power mode
immediately, or setting timeouts so that the drive will
automatically enter progressively lower power states after various
idle times.
sbin/camcontrol/fwdownload.c:
Update the firmware download code for the new build_ata_cmd()
arguments.
sbin/camcontrol/zone.c:
Implement support for Shingled Magnetic Recording (SMR) drives
via SCSI Zoned Block Commands (ZBC) and ATA Zoned Device ATA
Command Set (ZAC).
These specs were developed in concert, and are functionally
identical. The primary differences are due to SCSI and ATA
differences. (SCSI is big endian, ATA is little endian, for
example.)
This includes support for all commands defined in the ZBC and
ZAC specs.
sys/cam/ata/ata_all.c:
Decode a number of additional ATA command names in ata_op_string().
Add a new CCB building function, ata_read_log().
Add ata_zac_mgmt_in() and ata_zac_mgmt_out() CCB building
functions. These support both DMA and NCQ encapsulation.
sys/cam/ata/ata_all.h:
Add prototypes for ata_read_log(), ata_zac_mgmt_out(), and
ata_zac_mgmt_in().
sys/cam/ata/ata_da.c:
Revamp the ada(4) driver to support zoned devices.
Add four new probe states to gather information needed for zone
support.
Add a new adasetflags() function to avoid duplication of large
blocks of flag setting between the async handler and register
functions.
Add new sysctl variables that describe zone support and paramters.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
sys/cam/scsi/scsi_all.c:
Add command descriptions for the ZBC IN/OUT commands.
Add descriptions for ZBC Host Managed devices.
Add a new function, scsi_ata_pass() to do ATA passthrough over
SCSI. This will eventually replace scsi_ata_pass_16() -- it
can create the 12, 16, and 32-byte variants of the ATA
PASS-THROUGH command, and supports setting all of the
registers defined as of SAT-4, Revision 5 (March 11, 2016).
Change scsi_ata_identify() to use scsi_ata_pass() instead of
scsi_ata_pass_16().
Add a new scsi_ata_read_log() function to facilitate reading
ATA logs via SCSI.
sys/cam/scsi/scsi_all.h:
Add the new ATA PASS-THROUGH(32) command CDB. Add extended and
variable CDB opcodes.
Add Zoned Block Device Characteristics VPD page.
Add ATA Return SCSI sense descriptor.
Add prototypes for scsi_ata_read_log() and scsi_ata_pass().
sys/cam/scsi/scsi_da.c:
Revamp the da(4) driver to support zoned devices.
Add five new probe states, four of which are needed for ATA
devices.
Add five new sysctl variables that describe zone support and
parameters.
The da(4) driver supports SCSI ZBC devices, as well as ATA ZAC
devices when they are attached via a SCSI to ATA Translation (SAT)
layer. Since ZBC -> ZAC translation is a new feature in the T10
SAT-4 spec, most SATA drives will be supported via ATA commands
sent via the SCSI ATA PASS-THROUGH command. The da(4) driver will
prefer the ZBC interface, if it is available, for performance
reasons, but will use the ATA PASS-THROUGH interface to the ZAC
command set if the SAT layer doesn't support translation yet.
As I mentioned above, ZBC command support is untested.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
Add scsi_zbc_in() and scsi_zbc_out() CCB building functions.
Add scsi_ata_zac_mgmt_out() and scsi_ata_zac_mgmt_in() CCB/CDB
building functions. Note that these have return values, unlike
almost all other CCB building functions in CAM. The reason is
that they can fail, depending upon the particular combination
of input parameters. The primary failure case is if the user
wants NCQ, but fails to specify additional CDB storage. NCQ
requires using the 32-byte version of the SCSI ATA PASS-THROUGH
command, and the current CAM CDB size is 16 bytes.
sys/cam/scsi/scsi_da.h:
Add ZBC IN and ZBC OUT CDBs and opcodes.
Add SCSI Report Zones data structures.
Add scsi_zbc_in(), scsi_zbc_out(), scsi_ata_zac_mgmt_out(), and
scsi_ata_zac_mgmt_in() prototypes.
sys/dev/ahci/ahci.c:
Fix SEND / RECEIVE FPDMA QUEUED in the ahci(4) driver.
ahci_setup_fis() previously set the top bits of the sector count
register in the FIS to 0 for FPDMA commands. This is okay for
read and write, because the PRIO field is in the only thing in
those bits, and we don't implement that further up the stack.
But, for SEND and RECEIVE FPDMA QUEUED, the subcommand is in that
byte, so it needs to be transmitted to the drive.
In ahci_setup_fis(), always set the the top 8 bits of the
sector count register. We need it in both the standard
and NCQ / FPDMA cases.
sys/geom/eli/g_eli.c:
Pass BIO_ZONE commands through the GELI class.
sys/geom/geom.h:
Add g_io_zonecmd() prototype.
sys/geom/geom_dev.c:
Add new DIOCZONECMD ioctl, which allows sending zone commands to
disks.
sys/geom/geom_disk.c:
Add support for BIO_ZONE commands.
sys/geom/geom_disk.h:
Add a new flag, DISKFLAG_CANZONE, that indicates that a given
GEOM disk client can handle BIO_ZONE commands.
sys/geom/geom_io.c:
Add a new function, g_io_zonecmd(), that handles execution of
BIO_ZONE commands.
Add permissions check for BIO_ZONE commands.
Add command decoding for BIO_ZONE commands.
sys/geom/geom_subr.c:
Add DDB command decoding for BIO_ZONE commands.
sys/kern/subr_devstat.c:
Record statistics for REPORT ZONES commands. Note that the
number of bytes transferred for REPORT ZONES won't quite match
what is received from the harware. This is because we're
necessarily counting bytes coming from the da(4) / ada(4) drivers,
which are using the disk_zone.h interface to communicate up
the stack. The structure sizes it uses are slightly different
than the SCSI and ATA structure sizes.
sys/sys/ata.h:
Add many bit and structure definitions for ZAC, NCQ, and EPC
command support.
sys/sys/bio.h:
Convert the bio_cmd field to a straight enumeration. This will
yield more space for additional commands in the future. After
change r297955 and other related changes, this is now possible.
Converting to an enumeration will also prevent use as a bitmask
in the future.
sys/sys/disk.h:
Define the DIOCZONECMD ioctl.
sys/sys/disk_zone.h:
Add a new API for managing zoned disks. This is very close to
the SCSI ZBC and ATA ZAC standards, but uses integers in native
byte order instead of big endian (SCSI) or little endian (ATA)
byte arrays.
This is intended to offer to the complete feature set of the ZBC
and ZAC disk management without requiring the application developer
to include SCSI or ATA headers. We also use one set of headers
for ioctl consumers and kernel bio-level consumers.
sys/sys/param.h:
Bump __FreeBSD_version for sys/bio.h command changes, and inclusion
of SMR support.
usr.sbin/Makefile:
Add the zonectl utility.
usr.sbin/diskinfo/diskinfo.c
Add disk zoning capability to the 'diskinfo -v' output.
usr.sbin/zonectl/Makefile:
Add zonectl makefile.
usr.sbin/zonectl/zonectl.8
zonectl(8) man page.
usr.sbin/zonectl/zonectl.c
The zonectl(8) utility. This allows managing SCSI or ATA zoned
disks via the disk_zone.h API. You can report zones, reset write
pointers, get parameters, etc.
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D6147
Reviewed by: wblock (documentation)
That pops up in the rev 5xx / 6xx microcode on the later cores
(4312, 4322.) I'm not sure why this is happening yet and I'll
dig into it, but Linux b43 does the same thing.
* PMU controls the clock setup
* Correctly set idle low power handling
* Use a hard-coded powerup delay for some of the newer hardware
(including the BCM4322, which I've tested with.)
Tested:
* BCM4322, 2G + 5G STA mode
Obtained from: Linux b43 (PMU behaviour)
