The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.
Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix
* New error_flags that can be used from the error ithread and elsewhere
without a synch_op.
* Stop the adapter immediately in t4_fatal_err but defer most of the
rest of the handling to a task. The task is allowed to sleep, unlike
the ithread. Remove async_event_task as it is no longer needed.
* Dump the devlog, CIMLA, and PCIE_FW exactly once on any fatal error
involving the firmware or the CIM block. While here, dump some
additional info (see dump_cim_regs) for these errors.
* If both reset_on_fatal_err and panic_on_fatal_err are set then attempt
a reset first and do not panic the system if it is successful.
MFC after: 1 week
Sponsored by: Chelsio Communications
Recent firmwares have support for autonomous FEC selection and a "force"
knob to let the driver control this behavior (or not) in a fine grained
manner. This change adds a driver knob so that all the different ways of
configuring the link FEC can be exercised. Note that this controls the
internal driver/firmware interaction for link configuration and is not
meant for general use.
MFC after: 1 week
Sponsored by: Chelsio Communications
Recent firmwares are able to utilize the traffic classes of tx channels
that were previously unused. This effectively doubles the number of
traffic classes available per port for 2 port cards. Stop using the raw
per-channel value in the driver and ask the firmware for the number of
usable traffic classes instead.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
The hw.cxgbe.kern_tls tunable was used for this in the past and if it
was set then all T6 adapters would be configured for NIC TLS operation
and could not be reconfigured for TOE without a reload. With this
change ifconfig can be used to manipulate toe and txtls caps like any
other caps. hw.cxgbe.kern_tls continues to work as usual but its
effects are not permanent any more.
* Enable nic_ktls_ofld in the default configuration file and use the
firmware instead of direct register manipulation to apply/rollback
NIC TLS configuration. This allows the driver to switch the hardware
between TOE and NIC TLS mode in a safe manner. Note that the
configuration is adapter-wide and not per-port.
* Remove the kern_tls config file as it works with 100G T6 cards only
and leads to firmware crashes with 25G cards. The configurations
included with the driver (with the exception of the FPGA configs) are
supposed to work with all adapters.
Reported by: Veeresh U.K. at Chelsio
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Reviewed by: jhb@
Differential Revision: https://reviews.freebsd.org/D29291
T5 and above have extra bits for the optional filter fields. This is a
correctness issue and not just a waste because a filter mode valid on a
T4 (36b) may not be valid on a T5+ (40b).
MFC after: 2 weeks
Sponsored by: Chelsio Communications
1. Query the firmware for filter mode, mask, and related ingress config
instead of trying to figure them out from hardware registers. Read
configuration from the registers only when the firmware does not
support this query.
2. Use the firmware to set the filter mode. This is the correct way to
do it and is more flexible as well. The filter mode (and associated
ingress config) can now be changed any time it is safe to do so.
The user can specify a subset of a valid mode and the driver will
enable enough bits to make sure that the mode is maxed out -- that
is, it is not possible to set another bit without exceeding the
total width for optional filter fields. This is a hardware
requirement that was not enforced by the driver previously.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Read the PF-only hardware settings directly in get_params__post_init.
Split the rest into two routines used by both the PF and VF drivers: one
that reads the SGE rx buffer configuration and another that verifies
miscellaneous hardware configuration.
MFC after: 1 week
Sponsored by: Chelsio Communications
It is common for freelists to be starving when a netmap application
stops. Mailbox commands to free queues can hang in such a situation.
Avoid that by not freeing the queues when netmap is switched off.
Instead, use an alternate method to stop the queues without releasing
the context ids. If netmap is enabled again later then the same queue
is reinitialized for use. Move alloc_nm_rxq and txq to t4_netmap.c
while here.
MFC after: 1 week
Sponsored by: Chelsio Communications
The MAC address can be set with the optional mac-addr property in the VF
section of the iovctl.conf(5) used to instantiate the VFs.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Query the firmware for the MAC address set by the PF for the VF and use
it instead of the firmware generated MAC if it's available.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Hardware assistance includes checksumming (tx and rx), TSO, and RSS on
the inner traffic in a VXLAN tunnel.
Relnotes: Yes
Sponsored by: Chelsio Communications
Rx is more efficient within the chip when the receive buffer size
matches the TLS PDU size.
MFC after: 3 days
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D26127
- Ask the firmware for the number of frames that can be stuffed in one
work request.
- Modify mp_ring to increase the likelihood of tx coalescing when there
are just one or two threads that are doing most of the tx. Add teeth
to the abdication mechanism by pushing the consumer lock into mp_ring.
This reduces the likelihood that a consumer will get stuck with all
the work even though it is above its budget.
- Add support for coalesced tx WR to the VF driver. This, with the
changes above, results in a 7x improvement in the tx pps of the VF
driver for some common cases. The firmware vets the L2 headers
submitted by the VF driver and it's a big win if the checks are
performed for a batch of packets and not each one individually.
Reviewed by: jhb@
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D25454
should try in order to link up with the peer.
Various FEC variables within the driver can now have multiple bits set
instead of being powers of 2. 0 and -1 in the user knobs still mean no
FEC and auto (driver decides) respectively for backward compatibility,
but no-FEC and auto now have their own bits in the internal
representation. There is a new bit that can be set to request the FEC
recommended by the cable/transceiver module.
Add sysctls to display link related capabilities of the local side as
well as the link partner.
Note that all this needs a new firmware and the documentation for the
driver FEC knobs will be updated after that firmware is added to the
driver.
MFC after: 1 week
Sponsored by: Chelsio Communications
Recent firmwares prefer to use a different format for viid internally
and this change allows them to do so.
MFC after: 1 week
Sponsored by: Chelsio Communications
"slow" interrupt handler:
- Expand the list of INT_CAUSE registers known to the driver.
- Add decode information for many more bits but decouple it from the
rest of intr_info so that it is entirely optional.
- Call t4_fatal_err exactly once, and from the top level PL intr handler.
t4_fatal_err:
- Use t4_shutdown_adapter from the common code to stop the adapter.
- Stop servicing slow interrupts after the first fatal one.
Driver/firmware interaction:
- CH_DUMP_MBOX: note whether the mailbox being dumped is a command or a
reply or something else.
- Log the raw value of pcie_fw for some errors.
- Use correct log levels (debug vs. error).
Sponsored by: Chelsio Communications
card initialization. This is an expanded version of r333682.
Break up prep_firmware into simpler routines while here. Load the
firmware/config KLD only if needed.
MFC after: 1 month
Sponsored by: Chelsio Communications
- Switch to using 32b port/link capabilities in the driver. The 32b
format is used internally by firmwares > 1.16.45.0 and the driver will
now interact with the firmware in its native format, whether it's 16b
or 32b. Note that the 16b format doesn't have room for 50G, 200G, or
400G speeds.
- Add a bit in the pause_settings knobs to allow negotiated PAUSE
settings to override manual settings.
- Ensure that manual link settings persist across an administrative
down/up as well as transceiver unplug/replug.
- Remove unused is_*G_port() functions.
Approved by: re@ (gjb@)
MFC after: 1 month
Sponsored by: Chelsio Communications
own region in the TCAM starting with T6, unlike previous chips where
they were in the same region as normal filters.
These filters "hit" before anything else in the LE's lookup. The exact
order is:
a) High priority filters
b) TOE's active region (TCAM and/or hash)
c) Servers (TOE hw listeners)
d) Normal filters
MFC after: 1 week
Sponsored by: Chelsio Communications
traffic class for rate limiting.
Add experimental knobs that allow the user to specify a default pktsize
and burstsize for traffic classes associated with a port:
dev.<ifname>.<instance>.tc.pktsize
dev.<ifname>.<instance>.tc.burstsize
Sponsored by: Chelsio Communications
- Ignore any type of TID where the start/end values are not in the
correct order. There are situations where the firmware isn't able to
reserve room for the number requested in the config file but doesn't
report a failure during configuration and instead sets end <= start.
- Track start/end in tid_tab and remove some redundant copies from
adapter->params.
- Move all the start/end and other read-only parameters to a quiet part
of tid_tab, away from the tid locks.
MFC after: 1 week
Sponsored by: Chelsio Communications
for a port. Fix other related issues while here:
- Require port lock for access to link_config.
- Allow 100Mbps operation by tracking the speed in Mbps. Yes, really.
- New port flag to indicate that the media list is immutable. It will
be used in future refinements.
This also fixes a bug where the driver reports incorrect media with
recent firmwares.
MFC after: 2 days
Sponsored by: Chelsio Communications
- Driver support for hardware NAT.
- Driver support for swapmac action.
- Validate a request to create a hashfilter against the filter mask.
- Add a hashfilter config file for T5.
Sponsored by: Chelsio Communications
request, which can be used to configure hardware NAT and swapmac.
All firmwares released after Jan 2017 support this work request.
Sponsored by: Chelsio Communications
These filters reside in the card's memory instead of its TCAM and can be
configured via a new "hashfilter" subcommand in cxgbetool. Hash and
normal TCAM filters can be used together. The hardware does an
exact-match of packet fields for hash filters, unlike the masked match
performed for TCAM filters. Any T5/T6 card with memory can support at
least half a million hash filters. The sample config file with the
driver configures 512K of these, it is possible to double this to 1
million+ in some cases.
The chip does an exact-match of fields of incoming datagrams with hash
filters and performs the action configured for the filter if it matches.
The fields to match are specified in a "filter mask" in the firmware
config file. The filter mask always includes the 5-tuple (sip, dip,
sport, dport, ipproto). It can, optionally, also include any subset of
the filter mode (see filterMode and filterMask in the firmware config
file).
For example:
filterMode = fragmentation, mpshittype, protocol, vlan, port, fcoe
filterMask = protocol, port, vlan
Exact values of the 5-tuple, the physical port, and VLAN tag would have
to be provided while setting up a hash filter with the chip
configuration above.
Hash filters support all actions supported by TCAM filters. A packet
that hits a hash filter can be dropped, let through (with optional
steering to a specific queue or RSS region), switched out of another
port (with optional L2 rewrite of DMAC, SMAC, VLAN tag), or get NAT'ed.
(Support for some of these will show up in the driver in a follow-up
commit very shortly).
Sponsored by: Chelsio Communications
The TCB is read using a memory window right now. A better alternate to
get self-consistent, uncached information would be to use a GET_TCB
request but waiting for a reply from hw while holding non-sleepable
locks is quite inconvenient.
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D14817
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
different from hardware defaults. The congestion channel map, which is
still fixed, needs to be tracked separately now. Change the congestion
setting for TOE rx queues to match the drivers on other OSes while here.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
precision. These timers are already displayed in microseconds in the
sysctl MIB. Add variables to track these tunables while here.
MFC after: 3 days
Sponsored by: Chelsio Communications
and keepalive in the sysctl MIB. Provide tunables to change some of
these parameters. These are supposed to be setup by the firmware so
these tunables are for experimentation only.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
doesn't seem to have one. This lets the driver recover automatically
from incomplete firmware upgrades (panic, reboot, power loss, etc. in
the middle of an upgrade).
MFC after: 2 weeks
Sponsored by: Chelsio Communications
- Deal with changes to port_type, and not just port_mod when a
transceiver is changed. This fixes hot swapping of transceivers of
different types (QSFP+ or QSA or QSFP28 in a QSFP28 port, SFP+ or
SFP28 in a SFP28 port, etc.).
- Always refresh media information for ifconfig if the port is down.
The firmware does not generate tranceiver-change interrupts unless at
least one VI is enabled on the physical port. Before this change
ifconfig diplayed potentially stale information for ports that were
administratively down.
- Always recalculate and reapply L1 config on a transceiver change.
- Display PAUSE settings in ifconfig. The driver sysctls for this
continue to work as well.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
- Create a new file, t4_sched.c, and move all of the code related to
traffic management from t4_main.c and t4_sge.c to this file.
- Track both Channel Rate Limiter (ch_rl) and Class Rate Limiter (cl_rl)
parameters in the PF driver.
- Initialize all the cl_rl limiters with somewhat arbitrary default
rates and provide routines to update them on the fly.
- Provide routines to reserve and release traffic classes.
MFC after: 1 month
Sponsored by: Chelsio Communications
available starting with T6. The values in the timer holdoff registers
are multiplied by the scaling factor before use.
dev.<nexus>.<n>.holdoff_timers shows the final values of the
timers in microseconds.
MFC after: 1 week
Sponsored by: Chelsio Communications
- Update struct link_settings and associated shared code.
- Add tunables to control FEC and autonegotiation. All ports inherit
these values as their initial settings.
hw.cxgbe.fec
hw.cxgbe.autoneg
- Add per-port sysctls to control FEC and autonegotiation. These can be
modified at any time.
dev.<port>.<n>.fec
dev.<port>.<n>.autoneg
MFC after: 3 days
Sponsored by: Chelsio Communications
