extra trailing space.
- Don't bother probing a generic ISA bus device if isab0 already exists.
Some BIOSes place an ACPI psuedo-device with the HID of a generic ISA bus
device under the PCI-ISA bridge device. This is not the best solution
but will work for now. The isa bus driver only allows for one ISA bus
anyways.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
- Factor out code common to all ISA bridge drivers attach methods into a
isab_attach() function.
- Rename the PCI-ISA bridge driver's attach function to pci_isab_attach()
and have it call isab_attach().
the bulk out buffer size to 16 bytes. The bulk out endpoint descriptor
reports 32 bytes, but if you use this value, data will get dropped.
Reviewed/approved by: scottl
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
tested for playback.
* modify device name strings for ich chips to better conform with their
common names.
* remove superflous 'AC97 controller' from nforce device names.
MFC after: 1 week
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
However, they are presently necessary due to bigger bogusness in the
pci bus layer not doing the right thing on suspend/resume or on
initial device probe. This is exactly the sort of thing that the
BURN_BRIDGES option was invented for. Mark all of them as
BURN_BRIDGES. As soon as I have the powerstate stuff properly
integrated into the pci bus code, I intend to remove all these
workarounds.
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
careful to call all map_load calls with BUS_DMA_NOWAIT because we
really don't want some PDUs to wait while others go out - ATM guarantees
the ordering of cells and also of PDUs (within one VC, that is). With
BUS_DMA_NOWAIT bus_dmamap_load should never return EINPROGRESS.
Make the tag used for transmission buffers one larger than the maximum
AAL5 PDU (65535). This is needed, because all PDU sizes need to be round
up to multiple of four for the card and PDUs that are just below the
maximum size will be rounded up to 65536
real SATA disks now that I can test it.
Add support for the SiI 3112 SATA chip using memory mapped I/O.
Update the support for the SiI 0680 to use the memio interface as well.
Sponsored by: David Leimbach <leimy2k@mac.com> (3112 based controller)
Sponsored by: FreeBSD Systems (www.FreeBSDsystems.com) (SATA disks)
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
interrupt to be used for a device. This is intended solely for internal
use of PCI bus implementations, and exists so that PCI bus drivers
implementing special interrupt assignment methods which require
additional work at the bus level to work right can be easily derived
from the generic driver (or any other one) without resorting to hacks.
It will be used in the sparc64 ofw_pcibus driver, which will be
committed shortly.
Make use of this method in the generic implementation, and add it to
the method table of bus drivers derived from the PCI one.
Reviewed by: imp, -hackers
are some Sun PCI devices around which bogusly set intpin to 0, although
they use the intline mechanism; this allows the device driver to correct
that.
Reviewed by: imp
- Initialize fc->status to process bus reset correctly after resume.
- Initialize AT ring buffer pointer.
- Requeue stdma to stfree for active IR buffer.
- Stop DMA before suspend for safe.
- Set powerstate after resume.
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
to store an int in the bio->bio_driver1 (a void *). It is big enough,
but you have to match the int sizes first before doing the cast.
Glanced at by: scottl
software crypto device:
o record crypto device capabilities in each session id
o add a capability that indicates if the crypto driver operates synchronously
o tag the software crypto driver as operating synchronously
This commit also introduces crypto session id macros that cleanup their
construction and querying.
channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
o add back rx monitor support
o make WI_RID_SCAN_RES DTRT
o fix a bug handling zero-length RID requests (used by dstumbler to set
a zero-length SSID)
o make RID_SCAN_REQ DTRT
o add back WI_RID_OWN_SSID
o fix wi_scan_ap to take a channel mask and txrate (for prism cards)
These changes fix dstumbler -o (monitor mode). A minor change to dstumbler
is needed to get normal AP scanning mode to work right; this is preferred to
modifying the driver.
PR: kern/53187
Reviewed by: Bruce M Simpson <bms@spc.org>
flag'ed INTR_MPSAFE. In ep_if_start(), use the IF_DEQUEUE macro to
grab the next mbuf to send, and use IF_PREPEND if the card is busy
and we actually can't handle it right now.
The old code was first getting the mbuf by taking it from the queue
without using the macros, thus without locking, and without removing
it from the queue either. It was later assuming that IF_DEQUEUE would
give him this same mbuf.
Tested by: mich
when the user specifies a maximum fragment size < 2.
This is the behavior that Linux provides and fixes the problem I've
observed in Tribes2 where sounds effects are delayed by 1/2 a second.
so can leave stale data in the buffer and confuse the driver.
- enable the ability to set the 'disable' hint for the driver to keep it
from attaching. i.e. 'hw.ips.0.disable=1' will prevent the driver from
attaching.
- Only detach if attach suceeded.
Submitted by: mjacob
in the netisr case. This would result in a lock reversal. This
fixes the net.isr.enable=1 case. Better performance might be
obtained by chaining all packets received, dropping the lock, and
then calling if_input() on each one.
Reported by: hmp
of the contents of the CCSCBCTL register into our
local varaible. The other bits are used in later tests.
This avoids a potential deadlock in ahd_run_qoutfifo()
if we happen to catch the DMA engine in just the right
state.
read permision only required for listing, read/write required for
read/write to registers
fix a possible memory leak
clean up error handling a bit
Reviewed by: silence
Reorder how the pci probing in handled. before adding devices, check to
see if the slot is a multi-function device to see if we should probe all
the functions.
Original idea by: imp
drivers that implemnt the i2c bit banging bus interface not have to
recompile iicbb in order to add an attachment for it.
This will mean the bktr and other definitions can go back to their
respective drivers.
- Mark that it cannot handle greater than 4GB of RAM at this time. Fixing
that will come later. Fail any attempts to dump above thati limit.
- If a call to aac_disk_dump() needs to be split into multiple i/o's,
increment the virtual offset after each i/o instead of just dumping the
same offset over and over again.
- Bail out if bus_dmamap_load() returns an error. Error recovery is likely
not possible.
This version of the driver code is compatible with near-release FreeBSD 5.1
kernel/driver interfaces.
modules/Makefile, man page and other bindings to follow shortly, once I get
this part of the check-in right.
Approved by: markm(mentor)
Previously, any normal I/O on an fdc(4) device would fail with ENXIO
if the device had been opened in non-blocking mode and then closed
prior to the conventional access; that would last until the floppy
disk was ejected and re-inserted to raise the unit attention condition.
Add a clarifying comment.
populated. Apparently, if you use an ehci controller, it's not.
Use usbd_device2interface_handle() to retrieve the interface handle.
NOTE: uaa->iface is populated in the probe routine, so I suspect the
fact that it's NULL in the attach routine is a bug in the ehci driver.
Also, don't depend on the PHY addresses returned by the AXE_CMD_READ_PHYID
command. The address is correct for my LinkSys NIC, but a user has
reported that with a D-Link NIC, the PHYID command returns address 4
while the attached Broadcom PHY is in fact strapped for address 0.
Instead, latch onto the first PHY address that returns valid data
during a readreg operation.
as should every block device strategy routine.
There was at least one evil consequence of not doing so:
Some errors returned by fdstrategy() could be lost (EAGAIN,
in particular.)
PR: kern/52338 (in the audit-trail)
Discussed with: bde
to access floppy parameters through it.
Note: The DIOCGSECTORSIZE and DIOCGMEDIASIZE handlers withing
fdioctl() couldn't be just moved to below the existing check
for blocking mode because fd->ft can be non-NULL while still
in non-blocking mode (fd->ft can be set with the FD_STYPE ioctl.)
PR: kern/52338
No MFC: Not applicable to STABLE
ulpt_status() afterwards. This fixes a crash that can occur if a
USB printer is power-cycled when printing is just starting. The
problem is similar to that fixed in revision 1.33, but it is much
less likely to occur.
MFC after: 1 week
and return NULL.
vinum_scandisk: Don't handle NULL device pointers.
Only look at compatibility partition for i386. This
is a kludge which should go away once I have adequate
documentation for the New World Order.
Together, these fixes remove occasional error messages about
non-existent drives. They may also fix a number of problems that have
been reported without a PR.
PRs: None
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
how we registered pccard_intr, it is MPSAFE. However, since we
register the pccard_intr handler with the flags of the ISR we call,
that is the gating factor. We need do nothing specific here.
Prompted by: seeing pccard_intr in a panic.
are the same that those of the kernel in the KLD_MODULE case. If
we ever want to detect that kind of problems, this is not the right
place to do this since every network driver would be affected by
such desynchronisation.
toggle several media options (sonet/sdh, for example) with ifconfig and
to see the carrier state in ifconfig's output. It gives also read/write
access (given the right privilegs) to the S/Uni registers to user space
programs.
than once. This appears to work around the hanging issues, at the
expense of warnings about bad RID allocations. I'm not sure this is a
permanant workaround, but does appear to help in the tests that I've
done here.
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
doesn't have one. The test was bogus on these architectures, but
recent changes broke it altogether.
Prompted by: phk
This should fix the recent SPARC 64 build problems.
o Register ISR INTR_MPSAFE.
o Loop on KTHREAD_DONE == 0 in the thread.
o Safe the INTR_MPSAFE flag for client drivers (don't know if there are any
CardBus/PCI drivers that are INTR_MPSAFE)
o Read status after acquiring mtx_lock(Giant) rather than before so that we
catch state changes that happen while Giant is being acquired.
o Turn off the CD bit when we see a CD interrupt, and turn it back on after
we've attached/detached the card.
o On suspend, actually set the CBB_SOCKET_MASK to zero rather than oring
in '0' to turn it off on suspend.
o If the ISR that's registerd is MPSAFE, don't acquire Giant around call to
client ISR.
o Fix comments to reflect these changes.
ia64-specific.
- When trying to re-route interrupts, don't change cfg->intline if the
re-route fails by returning an invalid vector. This fixes machines
without any way of routing interrupts such as older PC's without a
$PIR table.
We do not currently write the new intline value back to the hardware, but
we should. That will likely be added in a later commit.
if it was already enabled. We don't want to set it
when it shouldn't be set, we just don't want to
inadvertantly turn it off. This should fix a recent
report of the aic7xxx driver repeatedly complaining of
"unexpected busfree while idle" in one configuration.
successfully mapping our registers. This
avoids the disabling of memory mapped I/O
just because some other driver probe happened
to touch our registers.
This drive delays going async after receiving a WDTR
message. We now send an SDTR message after a WDTR even
if our goal is to go async. This should work even for
confused devices.
If we get an unexpected busfree when attempting a WDTR
or SDTR, only set the goal negotiation parameters we were
trying to negotiate to off. This means that should a WDTR
message fail, we will still try an SDTR if our goal is
non-async.
Fix a few more places where we were looking at goal.period
instead of goal.offset for determining if we should be
negotiating sync. This should not have any impact on
our behavior, but the offset is more definitive and should
be used.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
aic7xxx.c:
aic7xxx.h:
aic7xxx_pci.c:
Switch ah?_reset() to take an additional "reinit" argument.
Use this instead of init_level to determin if the chip
should be fully reinitialized after a chip reset. This
is required so that ah?_shutdown() can reset the chip
without side-effects.
aic79xx.c:
Implement ahd_suspend() and ahd_resume().
aic7xxx.c:
Change ahc_loadseq() to *not* restart the sequencer.
This brings the loadseq behavior in line with that
of the 7902 driver and also simplifies the init routine.
Correct the resume routine to enable interrupts and
restart the sequencer.
obtained from o2micro. These should only be needed for 'older'
o2micro bridges (anything before the 7xxx series of bridges), but will
work with the new bridges.
# I don't plan on porting it to oldcard, but will happily commit to
# oldcard if someone else needs them.
Add sysctl's to display statistics/debug_info
Set WAIT_FOR_AUTONEG_DEFAULT to zero by default
Increment packet in/out statistics inline instead of every two seconds.
MFC after: 3 days
Always route PCI interrupts on i386 UP machines. I was planning to enable
this for i386 anyways once SMP support is done. Having this enabled fixes
problems on many people's laptops.
Requested by: imp
While a string is readable without a tool, an array is easier to process for
a monitoring application. This also prevents the extra hoops we need with
sbufs and locking.
Move the mtx_init() in en_attach() higher before the first failure point so
that we can unconditionally destroy it in en_destroy().
to unload. This would cause a panic on the second resetconfig.
Start Vinum at boot time at SI_SUB_RAID, not SI_SUB_VINUM.
SI_SUB_VINUM was there first, but there's no real distinction, and
SI_SUB_RAID is a more neutral name.
Submitted by: hmp
o adding locking to op submission
o mark interrupt handler MPSAFE
o don't use locking on detach; disabling interrupts should be sufficient
o change mutex string names so witness printouts are more meaningful
Note: locking is still pretty brute-force but it's probably not worth
improving it given the relatively low performance of hifn-based cards.
o replace driver-global lock with three locks: one for the handling of mcr1
operations, one for handling of mcr2 operations, and one for the mcr1
free list
o mark the interrupt handler MPSAFE
o don't use locking on detach; disabling interrupts is sufficient (I think)
Change the list interface to simplify things.
Remove old list ioctls which bogusly exported the softc to userland.
Move the softc and associated structures from the public header to
the source file.
Make CCD a GEOM class.
For now only use this for implementing a OAM config method which
can return a list of configured CCD devices in the format which
"ccdconfig -g[v]" would normally output.
bzero(ptr, sizeof(DC_RXLEN * 5));
which should obviously be:
bzero(ptr, DC_RXLEN * 5);
Looks like this bug may have reduced the effectiveness of the
workaround for the hardware bug in the PNIC chips.
MFC after: 1 week
o Remove register keyword
o ANSIfy prototypes
o Remove "return;" at the end of void functions
o Remove trailing spaces
o Don't align local variables with tabs and reorder them
o Don't use /* FOO */ at the end of a #ifdef FOO block if
it's a small block
- Other non-functional changes :
o 6 -> ETHER_ADDR_LEN
o Don't initialize if_output; ether_ifattach() does it for us
-Werror build with such option, but not other combinations. LINT
misses this because syscons knobs in LINT turn off a lot of code.
Reviewed by: marcel (some time ago)
Use the special LUNLEN_SINGLE_LEVEL constant for
post Rev A4 hardware for single byte luns. Without
this change, Rev B hardware would place the single
byte of lun data in byte 0 of the lun structure when
it should be in byte 1. Since there are few if any
devices on the market that support multiple luns in
target mode, the corrupted lun field (which was only
corrupted for non-zero luns) wasn't hurting us.
Approved by: re (rwatson)
aic79xx.h:
aic79xx.reg:
Return the SCB_TAG field to 16byte alignment.
It seems that on some PCI systems, SCBs are not
transferred correctly to the controller with
the previous placement of the SCB_TAG field.
Approved by: re (rwatson)
865. The APSIZE register has a variable-sized field of enabled bits.
To figure out how many bits a specific host bridge supports, write the
maximum width and see how many bits are set in the hardware. We then
use this mask for setting and getting the aperture size. Prior to this,
the agp(4) driver would treat an aperture size of 256 MB as 128 MB and
would not allocate enough physical memory for the GART as a result.
MFC after: 3 days
Sponsored by: The Weather Channel
Approved by: re (rwatson)
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
aic79xx.c:
In ahd_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic79xx_inline.h:
In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field.
aic79xx.reg:
Use the SCB_TASK_ATTRIBUTE field as a bit field in the
non-packetized case. We currently only define one bit,
SCB_XFERLEN_ODD.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic79xx.seq:
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx.c:
In ahc_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Ensure that SG_LIST_NULL is cleared in the
residual sg pointer for "mid-transfer" ignore
wide residue cases.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic7xxx.h:
Modify the SCB_GET_LUN() macro to mask the lun hardware
SCB field with LID. This leaves two bits in the LUN
field that can be used for other purposes.
aic7xxx.reg:
Change LID to be 0x3F. This is the maximum supported
lun size for non-packetized SCSI. Map the top bit
of the lun to SCB_XFERLEN_ODD. The host must set
this bit whenever a transfer is an odd length.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic7xxx.seq:
Be more careful in our handling of the SCB_LUN field. It
must be masked with LID if only lun information is desired.
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx_inline.h:
In ahc_queue_scb(), setup the SCB_XFERLEN_ODD field.
Approved by: RE
FAILDIS in the SEQCTL register, not the HCNTRL register.
aic7xxx.c:
Remeber SEQCTL settings in the "seqctl" field of our
softc. seqctl defaults to just having FASTMODE set,
but the bus attachments can override this.
aic7xxx.h:
Add the seqctl softc field.
aic7xxx_pci.c:
Update the seqctl softc field and manually update SEQCTL
when to many PCI errors occur
Approved by: RE
to be more efficient by having the sequencer copy the
single byte of valid lun data into the long lun field.
aic79xx.c:
Memset our hardware SCB to 0 so that untouched
fields don't confuse diagnostic output. With the
old method for handling the Rev A bug, if the long
lun field was not 0, this could result in bogus
lun information being sent to drives.
Use the same SCB transfer size for all chip types
now that the long lun is not DMA'ed to the chip.
aic79xx.seq:
Add code to copy lun information for Rev.A hardware.
aic79xx_inline.h:
Remove host update of the long_lun field on every
packetized command.
Sort IDs based on chip type.
Remove IROC IDs. We'll switch to using the IROC masks
if/when we want to start attaching to IROC controllers.
Approved by: RE
structure, which is new to the 82550 and 82551, is used to transmit
a packet. This appears to fix the packet truncation problem that was
observed when using 82550-based fxp cards to transmit ICMP or fragmented
UDP packets of certain lengths which only had one to three bytes in the
second and final mbuf of the packet. This matches a note in the "Intel
8255x 10/100 Mbps Ethernet Controller Family Open Source Software Developer
Manual", which says that the hardware parse bit should be set when sending
these types of packets.
There have also been unconfirmed reports of similar problems when
transmitting TCP packets, which should not be affected by the above
mentioned change because the hardware parse bit was already being set
if the stack requested hardware checksumming of the packet. If the
problem remains, the use of the IPCB structure can be disabled to
cause the driver to fall back to using the older 82559 interface with
82550-based cards by setting
hint.fxp.UNIT_NUMBER.ipcbxmit_disable
to a non-zero value at boot time, or using kenv to set this variable
before using kldload to load the fxp driver.
Approved by: re (jhb)
set on realtek cards, but they work without it (and don't work with
it). The standard seems to imply that this is just a hint anyway, so
this should be harmless. It doesn't appear to be set on any other
cardbus cards that I have (or have seen).
This should make the rl based CardBus cards work again. I've been
running it for about a month now.
Approved by: re@ (jhb)
buffer space instead of a u_int32_t. Otherwise the upper 32 bits of
the address space get truncated and syscons blows up.
Approved by: re (safe, low risk amd64 fixes)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
expand_table: Add parameters file and line if we're debugging.
Approved by: re (jhb)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
Add and clarify comments.
Approved by: re (jhb)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
Approved by: re (jhb)
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
update_volume_config: Remove redundant diskconfig parameter.
expand_table: Add parameters file and line if we're debugging.
Approved by: re (jhb)
Submitted by: Ted Unangst <tedu@stanford.edu>
Correct some inaccurate and badly formatted comments.
config_subdisk: If our drive is down, ensure that the subdisk is
crashed. Previously it was possible for the subdisk
to be up when the drive was down.
Change the way the plex lock mutexes work. Previously they were part
of the struct plex, which tore apart the mutex linked lists when the
plex table was expanded. Now we maintain a pool of mutexes (currently
32) to be shared by all plexes. This is still a lot better than the
splhigh() method used in other architectures.
update_volume_config: Remove redundant diskconfig parameter.
Approved by: re (jhb)
Change config format slightly to save plex preferences correctly.
vinum_scandisk: reinitialise volatile pointer after function call.
This is the "deafc0de" bug.
Approved by: re (scottl)
This fixes net/pppoa port for Alcatel Speedtouch devices.
Submitted by: Jay Cornwall <jay@evilrealms.net>
Tested by: Francois Rogler <francois@rogler.org>
Approved by: re (scottl)
on if_fxp cards. When flow control is enabled, if the operating system
doesn't acknowledge the packet buffer filling, the card will begin to
generate ethernet quench packets, but appears to get into a feedback
loop of some sort, hosing local switches. This is a temporary workaround
for 5.1: the ability to configure flow control should probably be
exposed by some or another management interface on ethernet link layer
devices.
Approved by: re (bmah)
Reviewed by: mux
all of the Optio series have the same problems. It might be a better
approach eventually to add wildcard support to USB quirks.
PR: kern/50271, kern/46369
Approved by: re (rwatson)
- Fix compilation without GEM_DEBUG.
- Do not #define GEM_DEBUG by default; it adds overhead (due to bzero()ing
RX space) and is not needed any more, since the driver is quite stable
now.
- Fix watchdog timeouts when failing to load TX packets.
- Do not forcibly limit the number of descriptors used for a packet to
GEM_NTXSEGS, by passing this number to bus_dma_tag_create(). There is
no requirement for a limit any lower than the total number of
available descriptors, and the present limit caused network problems
due to mbuf chains requiring more descriptors.
GEM_NTXSEGS is still used to estimate the interrupt window size, for
which we just need an estimate.
Approved by: re (rwatson)
The submitter of PR 32118 told me that this patch also fixes autoselecting
for znyx 4 port cards (10baseT, 100baseTX did work already).
PR: 32118
Reviewed by: imp
Approved by: rwatson (re)
has already been registered with ATAPI/CAM (else there is nothing
to do). atapi_cam_reinit_bus may be called before the bus is
registered if an ATAPI command times out during the boot sequence.
PR: i386/51421
Reviewed by: roberto
Approved by: re (rwatson)
MFC after: 1 week
by using a __packed keyword for the fxp_rfa structure. The Intel
guys who designed this structure with unaligned fields deserve
to be shot.
Tested by: kris
Approved by: re@ (jhb)
bus_dma MD code for AMD64. (And a trivial ifdef update in dev/kbd because
of this). More updates are needed here to take advantage of the 64 bit
instructions.
Approved by: re (blanket amd64/*)
- Simplify and correct the bus manager election process.
- Check link_active when choosing cycle master.
- Fix location of the cmr bit.
Approved by: re (scottl)
series. This driver was generously developed and released by David
Jeffreys and Adaptec. I've updated it to work with 5.x and fixed a
few bugs.
MFC After: 1 week
ASIC revision is really the major number of the CHIPID. Also store
the chipid, asic rev and chip revision in the softc for later use.
- The write twice to send producer index workaround only applies to
the 5700_BX chips, so only do it there.
Requested by: jdp
- Do not initalize the LED's to 0x00. The default configuration
the chip comes up in should yeild proper operation of the LED's.
Confirmed by: John Cagle <john.cagle@hp.com>
Approved by: re (blanket)
ILMI daemons. Factor out common softc fields for all ATM interfaces that
need to be externally visible into an ifatm structure and make the midway
driver using this structure and fill the MIB.
Maintain sector sizes for all objects, not just for drives. Some of
this could do with improvement: in particular, we get an error if the
components of an object have different sector sizes.
Clean up some comments.
the -v option, though it's not clear that it won't bite us elsewhere.
Forgotten by: phk
Implement setreadpol() function for the VINUM_READPOL ioctl.
Submitted by: Allan Saddi <allan@saddi.com>
with it.
Finally implement read policies. The previous "implementation" didn't
work because it referred to plexes which were almost invariably when
referred to. Instead, deprecate the "prefer" keyword for volumes
(though it's still there for the moment) and add a keyword "preferred"
to the plex definition. The relationship is like this:
Old:
vol foo ... prefer foo.p3
New:
plex foo.p3 volume foo preferred
print_config: Print "preferred" where appropriate.
No longer print "prefer" on volume config entries.
work because it referred to plexes which were almost invariably when
referred to. Instead, deprecate the "prefer" keyword for volumes
(though it's still there for the moment) and add a keyword "preferred"
to the plex definition. The relationship is like this:
Old:
vol foo ... prefer foo.p3
New:
plex foo.p3 volume foo preferred
give_plex_to_volume: set preferred plex if specified on plex
definition entry. This involves adding a parameter to the function to
specify the preferred plex.
config_plex: Implement preferred keyword.
Add ioctl VINUM_READCONFIG which implements both the "read" and
"start" commands in vinum(8). Aim for marginally better error
messages when something goes wrong.
Switch to handling bad SCSI status as a sequencer interrupt
instead of having the kernel proccess these failures via
the completion queue. This is done because:
o The old scheme required us to pause the sequencer and clear
critical sections for each SCB. It seems that these pause
actions, if coincident with a sequencer FIFO interrupt, would
result in a FIFO interrupt getting lost or directing to the
wrong FIFO. This caused hangs when the driver was stressed
under high "queue full" loads.
o The completion code assumed that it was always called with
the sequencer running. This may not be the case in timeout
processing where completions occur manually via
ahd_pause_and_flushwork().
o With this scheme, the extra expense of clearing critical
sections is avoided since the sequencer will only self pause
once all pending selections have cleared and it is not in
a critical section.
aic79xx.c
Add code to handle the new BAD_SCB_STATUS sequencer
interrupt code. This just redirects the SCB through
the already existing ahd_complete_scb() code path.
Remove code in ahd_handle_scsi_status() that paused
the sequencer, made sure that no selections where
pending, and cleared critical sections. Bad
status SCBs are now only processed when all of these
conditions are true.
aic79xx.reg:
Add the BAD_SCB_STATUS sequencer interrupt code.
aic79xx.seq:
When completing an SCB upload to the host, if
we are doing this because the SCB contains non-zero
SCSI status, defer completing the SCB until there
are no pending selection events. When completing
these SCBs, use the new BAD_SCB_STATUS sequencer
interrupt. For all other uploaded SCBs (currently
only for underruns), the SCB is completed via the
normal done queue. Additionally, keep the SCB that
is currently being uploaded on the COMPLETE_DMA_SCB
list until the dma is completed, not just until the
DMA is started. This ensures that the DMA is restarted
properly should the host disable the DMA transfer for
some reason.
In our RevA workaround for Maxtor drives, guard against
the host pausing us while trying to pause I/O until the
first data-valid REQ by clearing the current snapshot
so that we can tell if the transfer has completed prior
to us noticing the REQINIT status.
In cfg4data_intr, shave off an instruction before getting
the data path running by adding an entrypoint to the
overrun handler to also increment the FIFO use count.
In the overrun handler, be sure to clear our LONGJMP
address in both exit paths.
Perform a few sequencer optimizations.
aic79xx.c:
Print the full path from the SCB when a packetized
status overrun occurs.
Remove references to LONGJMP_SCB which is being
removed from firmware usage.
Print the new SCB_FIFO_USE_COUNT field in the
per-SCB section of ahd_dump_card_state(). The
SCB_TAG field is now re-used by the sequencer,
so it no longer makes sense to reference this
field in the kernel driver.
aic79xx.h:
Re-arrange fields in the hardware SCB from largest
size type to smallest. This makes it easier to
move fields without changing field alignment.
The hardware scb tag field is now down near the
"spare" portion of the SCB to facilitate reuse
by the sequencer.
aic79xx.reg:
Remove LONGJMP_ADDR.
Rearrange SCB fields to match aic79xx.h.
Add SCB_FIFO_USE_COUNT as the first byte
of the SCB_TAG field.
aic79xx.seq:
Add a per-SCB "Fifos in use count" field and use
it to determine when it is safe (all data posted)
to deliver status back to the host. The old method
involved polling one or both FIFOs to verify that
the current task did not have pending data. This
makes running down the GSFIFO very cheap, so we
will empty the GSFIFO in one idle loop pass in
all cases.
Use this simplification of the completion process
to prune down the data FIFO teardown sequencer for
packetized transfers. Much more code is now shared
between the data residual and transfer complete cases.
Correct some issues in the packetized status handler.
It used to be possible to CLRCHN our FIFO before status
had fully transferred to the host. We also failed to
handle NONPACKREQ phases that could occur should a CRC
error occur during transmission of the status data packet.
Correct a few big endian issues:
aic79xx.c:
aic79xx_inline.h:
aic79xx_pci.c:
aic79xx_osm.c:
o Always get the SCB's tag via the SCB_GET_TAG acccessor
o Add missing use of byte swapping macros when touching
hscb fields.
o Don't double swap SEEPROM data when it is printed.
Correct a big-endian bug. We cannot assign a
o When assigning a 32bit LE variable to a 64bit LE
variable, we must be explict about how the words
of the 64bit LE variable are initialized. Cast to
(uint32_t*) to do this.
aic79xx.c:
In ahd_clear_critical_section(), hit CRLSCSIINT
after restoring the interrupt masks to avoid what
appears to be a glitch on SCSIINT. Any real SCSIINT
status will be persistent and will immidiately
reset SCSIINT. This clear should only get rid of
spurious SCSIINTs.
This glitch was the cause of the "Unexpected PKT busfree"
status that occurred under high queue full loads
Call ahd_fini_scbdata() after shutdown so that
any ahd_chip_init() routine that might access
SCB data will not access free'd memory.
Reset the bus on an IOERR since the chip doesn't
seem to reset to the new voltage level without
this.
Change offset calculation for scatter gather maps
so that the calculation is correct if an integral
multiple of sg lists does not fit in the allocation
size.
Adjust bus dma tag for data buffers based on 39BIT
addressing flag in our softc.
Use the QFREEZE count to simplify ahd_pause_and_flushworkd().
We can thus rely on the sequencer eventually clearing ENSELO.
In ahd_abort_scbs(), fix a bug that could potentially
corrupt sequencer state. The saved SCB was being
restored in the SCSI mode instead of the saved mode.
It turns out that the SCB did not need to be saved at all
as the scbptr is already restored by all subroutines
called during this function that modify that register.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
Add support for parsing the seeprom vital product
data. The VPD data are currently unused.
aic79xx.h:
aic79xx.seq:
aic79xx_pci.c:
Add a firmware workaround to make the LED blink
brighter during packetized operations on the H2A.
aic79xx_inline.h:
The host does not use timer interrupts, so don't
gate our decision on whether or not to unpause
the sequencer on whether or not a timer interrupt
is pending.
aic7xxx.h:
Split out core chip initialization into ahc_chip_init().
This will allow us to reset the chip correctly at times
other than initial chip setup.
aic7770.c
aic7xxx_pci.c:
Flesh out bus chip init methods for our two
bus attachments and use these, in addition to
bus suspend/resume hooks to get the core in
better shape for handling these events.
When disabling PCI parity error checking, use FAILDIS.
Although the chip docs indicate that clearing PERRESPEN
should also work, it does not.
Auto-disable pci parity error checking after informing
the user of AHC_PCI_TARGET_PERR_THRESH number of parity
errors observed as a target.
aic7xxx.h:
aic7xxx_pci.c
aic7770.c
aic7xxx.c
Add the instruction_ram_size softc field.
Remove the now unused stack_size softc field.
Modify ahc_loadseq to return a failure code
and to actually check the downloaded instruction
count against the limit set in our softc.
Modify callers of ahc_loadseq to handle load
failures as appropriate.
Set instruction RAM sizes for each chip type.
aic7xxx_pci.c:
Add some delay in the aic785X termination
control code. This may fix problems with
the 2930.
Be consistent in how we access config space
registers. 16bit registers are accessed using
16bit ops.
aic7xxx.c:
Correct spelling errors.
Have ahc_force_renegotiation() take a devinfo as is done
in the U320 driver. Use this argument to correct a bug
in the selection timeout handler where we forced a renegotiation
with the last device that had set SAVED_SCSIID. SAVED_SCSIID
is only updated once a selection is *sucessfull* and so is
stale for any selection timeout.
Cleanup the setup of the devinfo for busfree events. We
now use this devinfo for a call to ahc_force_renegotiation()
at the bottom of the routine, so it must be initialized in
all cases.
In ahc_pause_and_flushwork(), adjust the loop so that it
will exit in the hot-eject case even if the INT_PEND mask
is something other than 0xFF (as it is in this driver).
Correct a wrapping string constant.
Call ahc_fini_scbdata() after shutdown so that
any ahc_chip_init() routine that might access
SCB data will not access free'd memory.
Correctly setup our buffer tag to indicate that 39bit
addressing is available if in 39bit addressing mode.
Rearrange some variable declarations based on
type size.
aic7xxx.c
aic7xxx.h:
aic7xxx.reg:
Consistently use MAX_OFFSET for the user max syncrate
set from non-volatile storage. This ensures that the
offset does not conflict with AHC_OFFSET_UNKNOWN.
Change AHC_OFFSET_UNKNOWN to 0xFF. This is
a value that the curr->offset can never be,
unlike '0' which we previously used. This
fixes code that only checks for a non-zero
offset to determine if a sync negotiation
is required since it will fire in the unknown
case even if the goal is async.
Change MAX_OFFSET to 0x7f which is the max
offset U160 aic7xxx controllers can negotiate.
This ensures that curr->offset will not
match AHC_OFFSET_UNKNOWN.
aic7xxx_inline.h:
Have our inline interrupt handler return with a value
indicating whether we serviced a real interrupt. This
is required for Linux support.
Return earlier if the interrupt is not for us.
patch workarounds for each phy revision.
Obtained from: NetBSD & Broadcom Linux driver
- Disable AUTOPOLL when accessing the PHY as it may cause PCI errors.
Obtained from: NetBSD
- Check the UPDATED bit in the status block so the driver knows
that the status block as indeed changed since the last access.
Broadcom documentation states drivers should unset the UPDATED/CHANGED
bits after reading them.
- When changing media types, first loop the phy then set the media.
Broadcom documentation and Linux drivers do this and I observed
much better handling of link after this change.
- Broadcom documentation states that for 1000BaseT operation,
autonegotiation must be enabled. Fix hard coding of media so that
the driver only advertises 1000BaseT as the supported media type
and enable autonegotition.
- Only set Master/Slave on the 5701.
Obtained from Broadcom Linux driver.
- Use htole* macros where appropriate so that the driver could work on non-x86 architectures
- Use m_getcl() instead of MGETHDR/MCLGET macros
Submitted by: sam (Sam Leffler)
Note: this might print failure messages on some systems, unfortunatly
the info from the device, stating if flushing is supported, cannot be trusted
so the operation is always issued on all devices, just in case...
just return it. Don't try to reinitialize it. This should fix a
number of inconsistencies that some people encountered with "vinum
start".
PR: 30588
PR: 43475
of <machine/pc/bios.h> specific to i386 and added a conditional define
for BIOS_PADDRTOVADDR that depends on ISA_HOLE_START. The latter is
undefined on alpha and ia64. Since the former is defined the same on
both alpha and ia64, assume the ISA_HOLE_START dependent definition
is specific to amd64 and use the identity-mapping in all other cases.
This of course is getting uglier every day...
project by providing documentation (under NDA) and hardware for
testing. This commit is the first result of the cooperation, and
adds support for several of their new controllers that we didn't
support before (and probably newer would have without this arrangement).
Add support for the Promise SATA150 TX2/TX4 and the Promise TX4000
controllers. This also adds support for various motherboard fitted
Promise SATA/ATA chips.
Note that this code uses memory mapped registers to minimize overhead.
I belive FreeBSD has made another first in the Open Source world
by being able to release support for this :)
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
Rewrite minor number decoding. Now we have only three types of
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
Correct formats for some error messages. Don't cast the value to
match the format.
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
Tidy up comments.
Check for null rqgs. This continue to be reported, though I can't
work out why.
Correct formats for some error messages. Don't cast the value to
match the format.
Use microtime, not getmicrotime, for timing debug entries.
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
As a result of the minor number changes, split out the superdevice
handling into a separate function, vinum_super_ioctl. This was most
of the code of vinumioctl.
attachobject: Improve error checking.
init_drive: Rephrase error message text.
Remove dead code (inside #if 0).
Change name of find_drive_by_dev to the more descriptive
find_drive_by_name.
Tidy up comments.
get_emppty_drive: Fix a day one bug with strcpy parameters.
Change name of find_drive_by_dev to the more descriptive
find_drive_by_name.
Rewrite minor number decoding. Now we have only three types of
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
object: subdisks, plexes and volumes. The encoding for plexes and
subdisks no longer reflects the object to which they belong. The
super devices are high-order volume numbers. This gives vastly more
potential volumes (4 million instead of 256).
Remove an unnecessary goto.
vinumopen: Return EINVAL, not ENXIO, on an attempt to open a
referenced plex.
at all (ie reads yield constant values). Display the width as the
difference between max and min so that constant timers have width
zero.
o Get the address of the timer from the XPmTmrBlk field instead of
the V1_PmTmrBlk field. The former is a generic address and can
specify a memory mapped I/O address. Remove <machine/bus_pio.h>
to account for this. The timer is now properly configured on
machines with ACPI v2 tables, whether PIO or MEMIO. Note that
the acpica code converts v1 tables into v2 tables so the address
is always present in XPmTmrBlk.
o Replace the TIMER_READ macro with a call to the read_counter()
function and add a barrier to make sure that we observe proper
ordering of the reads.
Check for suspend before the device polling, rather than after it.
Check to see if the current thread owns the lock in ioctl and return
EBUSY if it does.
This advances the locking to the point that I can eject my fxp card 10
times in a row, but I agree with Jeff Hsu that we need to get the
network layer locking finished before chasing more of the races here
(actually, he doesn't think this set is worth it even). There's a
number of races between FXP_LOCK in detach and all other users of
FXP_LOCK, and this gets back to the 'device with sleepers being
forcibly detached' problem as well...
* AcpiOsDerivePciId(): finds a bus number, given the slot/func and the
acpi parse tree.
* AcpiOsPredefinedOverride(): use the sysctl hw.acpi.os_name to
override the value for _OS.
Ideas from: takawata, jhb
Reviewed by: takawata, marcel
Tested on: i386, ia64
(currently) only consumer (en).
Add a sysctl node hw.atm where the atm drivers will hook on their hardware
sysctl sub-trees.
Make atm_ifattach call if_attach and remove the corresponding call to if_attach
from en. Create atm_ifdetach and use that in en.
While the last change actually changes the interface this is not a problem in
practice because the only other consumer of this API is an older LANAI driver
on the net, that is not ready for current anyway.
Reviewed by: -atm
ia64 by defining them in terms of newbus. Add a static inline for
fillw(), which doesn't have anything to do with I/O.
It's still ugly, but now the ugliness can be removed from ia64
specific headers.
1) always call fxp_stop in fxp_detach. Since we don't read from
the card, there's no need to carefully look at things with
bus_child_present.
2) Call FXP_UNLOCK() before calling bus_teardown_intr to avoid
a possible deadlock reported by jhb.
3) add gone to the softc. Set it to true in detach.
4) Return immediately if gone is true in fxp_ioctl
5) Return immediately if gone is true in fxp_intr
that one cannot generally hold a lock and call bus_teardown_intr.
This is race free with wi_intr because bus_teardown_intr won't allow
wi_intr to be called after it returns.
# jeff hsu points out that there might be a race between this unlock
# and wi_start. While that may be true also, it won't impact this commit.
Submitted by: jhb
as 64-bit architectures won't like this. Use virtual array indexes
instead. This *should* allow the driver to work on 64-bit platforms,
though it's still not endian clean.
firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets
past doing dhclient, but hangs on transmit a little after the ip
address is set. The 1.50.12 card has always been 'cranky' and Bill
Paul's tearing it apart at FreeBSD '99 hasn't helped.
sc_reset and sc_enable are subtlely different things. sc_reset means
exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE
has been sent to the card without a WI_CMD_DISABLE following." This
is a little different than what they mean on NetBSD (where both of
these concepts are comingled). NetBSD will try to only enable symbol
cards once, while FreeBSD only sends the WI_CMD_INI once.
Also, only try once to reset the card on a symbol.
This makes the lucent cards no worse than before, but apparently not
much better either. I got fewer hangs in my testing than I have in
the past, but I don't know if it is statistically significant or not.
"Ian gave me this patch" I assume this is iadowse@.
Also, pull in a few devices NetBSD's table. More are there, but I need
to properly move them to pccarddev before including them here.
- Remove getcsrdata().
- Don't print device type, this can be obtained by fwcontrol.
Tested with: Maxtor 5000XT
Tested by: Daniel O'Connor <doconnor@gsoft.com.au>
following changes have been done:
- stylify. The original code was too hard to read.
- get rid of a number of compilation options (Adaptec-only, Eni-only, no-DMA).
- more debugging features.
- locking. This is not correct yet in the absence of interface layer locking,
but is correct enough to not to cause lock order reversals.
- remove RAW mode. There are no users of this in the tree and I doubt that
there are any.
- remove NetBSD compatibility code. There was no way to keep NetBSD non-busdma
and FreeBSD busdma code together.
- if_en now buildable as a module.
This has been actively tested on sparc64 and i386 with ENI server and
client cards and an Adaptec card (thanks to kjc).
Reviewed by: mdodd, arr
- Add fxp_start_body() and change fxp_start() to just acquire locks and
then call fxp_start_body(). Places that would call fxp_start() with
locks held (mutex recursion) now call fxp_start_body() directly.
Remove MTX_RECURSE flag from sc_mtx. [gallatin]
- Change fxp_attach() to work without the softc lock, saving interrupt
hooking until the head of fxp_attach().
- Call ether_ifattach() before overriding ifp parameters. This reverts
part of 1.155.
- Remove multiple error paths in fxp_attach().
- Teardown interrupt in fxp_detach() before unlocking the softc.
- Make sure mutex is not held in fxp_release()
- Delete the miibus instance and/or self in fxp_release(), not in
fxp_detach(). This can happen if attach fails partway through.
- Move ifmedia_removeall to fxp_release() since attach may fail after
media have been allocated.
- Add locking to fxp_suspend, fxp_resume, fxp_start, fxp_intr,
fxp_poll, fxp_tick, fxp_ioctl, fxp_watchdog.
- Pass in ifp to fxp_intr_body since its callers sometimes already use
it.
- Add compatibility define for INTR_MPSAFE for 4.x. [gallatin]
- You don't need to bzero softc.
Ideas from: gallatin, mux
Tested by: >400M packets of dd/ssh, NFS, ping on i386 UP
driver at long last!
Many thanks to vaidas.damosevicius@if.lt for keeping this issue alive
and pursuing Intel for a fix, Intel/ICP for working on the driver, and
Sergey Osokin for bringing the original patches up to 5-CURRENT.
of the infrastructure for the gamma driver which was removed a while back.
The DRM_LINUX option is removed because the handler is now provided by the
linux compat code itself.
(with other names) in the USB driver sources, but I felt that pcireg.h
should have a complete list - at least of classes and interfaces that we
know about and use.
or sched_lock are sufficient to test this flag.
XXX: vinum should really be using a kernel process via kthread_create()
instead of this hack. I'm not even sure PS_INMEM can be clear at this
point anyways.
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
other initializations succeeded.
- Initialize the TX and RX rings in epic_attach() rather than in
epic_init() where we're not supposed to fail. Similarly, free
the TX and RX rings in epic_detach() rather than in epic_stop().
- Change epic_init() to be a void function now that it can't fail.
Also change its parameter to a void * so that we have a correct
prototype for if_init.
- Now that epic_init() has a correct prototype, don't cast the
function pointer when initializing if_init.
- Fix nearby style bugs.
- Don't initialize if_output, ether_ifattach() does this for us.
- Use pci_enable_busmaster() instead of using pci_read_config()
and pci_write_config() directly.
- Don't try to enable I/O, bus_alloc_resource() does this for us.
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
bytes_in_mbuf rather than MCLBYTES. Add the ethertnet header to the
front of the mbuf. Adjust bytes_in_mbuf inside the loop that reads
the packet out of the card.
codec during initialization. This code mirrors the reset code used on
the VIA82c686 and fixes a codec initialization failure (SoundMAX
AD1885) reported by Matthias Schuendehuette.
in dc_detach() instead of only calling it if the hardware is preset.
This is a workaround for page faults in softclock() after a `dc'
device was detached, caused by not disabling a timer before freeing
its memory. The bus_child_present() checks should probably be
re-added later, but only to avoid the hardware accesses and not the
other resource cleanups in dc_stop().
Approved by: njl
Many internal structure changes for the FireWire driver.
- Compute CRC in CROM parsing.
- Add support for configuration ROM build.
- Simplify dummy buffer handling.
- busdma conversion
- Use swi_taskqueue_giant for -current. Mark the interrupt routine as MPSAFE.
- AR buffer handling.
Don't reallocate AR buffer but just recycle it.
Don't malloc and copy per packet in fwohci_arcv().
Pass packet to fw_rcv() using iovec.
Application must prepare receiving buffer in advance.
- Change fw_bind API so that application should pre-allocate xfer structure.
- Add fw_xfer_unload() for recycling struct fw_xfer.
- Add post_busreset hook
- Remove unused 'sub' and 'act_type' in struct fw_xfer.
- Remove npacket from struct fw_bulkxfer.
- Don't call back handlers in fwochi_arcv() if the packet has
not drained in AT queue
- Make firewire works on big endian platform.
- Use native endian for packet header and remove unnecessary ntohX/htonX.
- Remove FWXFERQ_PACKET mode. We don't use it anymore.
- Remove unnecessary restriction of FWSTMAXCHUNK.
- Don't set root node for phy config packet if the root node is
not cycle master capable but set myself for root node.
We should be the root node after next bus reset.
Spotted by: Yoshihiro Tabira <tabira@scd.mei.co.jp>
- Improve self id handling
Tested on: i386, sparc64 and i386 with forced bounce buffer
command config register. At the present, this represents a nop
because these bits should have been set earlier in the process. In
the future, we'll only set these bits when the driver requests the
resource, not when the bus code detects the resource.
Reviewed by: mdodd
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
PCIM_CMD_MEMEN and PCIM_CMD_BUSMASTEREN, becaise some braindead
BIOSes (such as one found in my vprmatrix notebook) forget
to initialize it properly resulting in attachment failure.
the list of supported sleep state.
This should help people understand what following message means.
acpi0: AcpiGetSleepTypeData failed - AE_NOT_FOUND
MFC after: 3 days
- Remove a useless device_is_alive() check.
- Disable interrupts if bus_child_present() so that this
check is more useful.
This fixes the hangs I was seeing when unloading the fxp driver.
Suggestions from: hsu, njl
- Be sure to teardown the interrupt first so that "kldunload if_fxp"
doesn't panic the box. It's now deadlocking rather than crashing,
which isn't really better, but I'm unsure this is fxp(4)'s fault.
- Change a bus_dmamap_sync() call to also do a BUS_DMASYNC_PREREAD
now that we can pass several operations.
is required. NetBSD has one because it checks for the mac address
match as well wanting to give its own string in the description.
Since we do neither, we don't need a separate entry.
# I suspect that a few of the COREGA cards might fall into that category
# as well, but since I don't have access to any of them it is hard to know
# for sure.
enet_mcast fields, so remove them. Sort. Eliminate now duplicate
entries.
This reorg saves about 500 bytes in the binary. I've tested this only
with a couple of cards, so please let me know if I've broken anything.
1.182; christos
A cardflash NE2000 from Michael Francini
1.181; perry
support Corega PCCL-11 -- from Christopher SEKIYA in PR 20932
1.180; ichiro
add product TOSHIBA PA2673U CBIDE2 (IODATA OEM)
1.179; kanaoka
Add SMC 8041TX 10/100 Ether PC Card.
0 in a problem that is being discussed. That means that the test for
product != 0 may cause problems. Looking at pccarddevs (which i
should have done earlier) we see:
product BONDWELL B236 0x0000 Game Card Joystick
product CONTEC CNETPC 0x0000 Contec C-NET(PC)C
product IBM MICRODRIVE 0x0000 IBM Microdrive
product RAYTHEON WLAN 0x0000 WLAN Adapter
product SOCKET EA_ETHER 0x0000 Socket Communications EA
product TDK LAK_CD011WL 0x0000 TDK LAK-CD011WL
so use only the vendor field for the end sentinel.
- Don't bother setting OACTIVE when the descriptors are all full
or there's a vr_encap failure, it doesn't help anything.
- Correctly roll back on the descriptor list after a failure
so as not to corrupt the list.
- Add a missing VR_UNLOCK().
Without these changes, vr_encap failure (which is assured during
a low mbuf situation) would result in the card locking until
the watchdog could fire.
MFC after: 1 week
Boost sample rate to 1.25 MSPS since that allows us to use a 5Mhz
(/4) or 10Mhz (/8) external clock.
Make the interrupt both MPSAFE and FAST, at 610 interrupts a second,
and a max time to service of 5 msec, we brake for nobody.
Use kernel thread to accumulate into the 25 possible wave signals.
Use #ifdef _KERNEL to let .c file double as .h file defining the ioctls.
of the entries have a description, we'll use that to override the
description that the pccard layer generates for us.
This saves about 930 bytes in the module, so I feel it won't hurt the
crowded boot disks....
# other modules to follow
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
o Only complain about detached children that aren't pccard/cardbus.
o Don't NULL out the pccarddev and cbdev devices. detach just
disassociates the device and driver. It doesn't delete the child.
o on driver added, just probe_and_attach the children. If there's
any children attached, wakeup the device add/delete thread.
o wakeup the add/delete thread with the correct cv_signal() rather
than the bogus wakeup(sc). It used to be that we did a tsleep on
sc in this thread, but switched to the more reliable cv stuff a while
ago w/o changing this.
o Remove bogus checks when reallocating memory for the registers. They
weren't needed and turned out to be completely bogus.
This lets me load/unload pccard with a pccard in a slot and have the
child correctly detach/attach. This should help people that have wi
in their kernel, but that kldload cbb and pccard, for example.
we're using an atomic operation to clear the suspend flag
in fxp_start(). Since other architectures may need the
same thing, we want to do it all the time and not only
in the __alpha__ case. However, we don't want to use
atomic operations on 16-bit integers, because those may
not be available on any architecture. We're thus faking
a 32-bit atomic operation here. This patch also deals
with endianness here.
which deals with both endianness and alignment issues.
- Collect low-hanging fruits for endianness safety.
- Use 0xffffffff instead of -1 where appropriate.
endian safe.
- Change some u_int to u_int8_t which make more sense here since
we're really defining bytes. That produces the same code due to
how bitfields work.
- Add the definition of the vlan_drop_en bit (not used yet).
- Add some useful comments.
Obtained from: NetBSD
other allocations/initializations have been successful. I kinda
doubt it will fix the recent breakage that some people are seeing,
but this could have caused problems for sure.
actual address of buffer descriptor. This should fix the reported
calibration failures and subsequent speed problems with ich chipsets.
Minor calibration comment updates.
This patch is rather big because I had to significantly redesign
the driver to make the busdma conversion possible. Most notably,
hardware and software structures were carefully splitted to get
rid of all the structs overlapping evilness.
Special thanks to phk and Richard Puga <puga@mauibuilt.com> for
providing me with fxp(4) hardware to do this work.
Thanks to marcel for testing this on ia64, and to Fred Clift
<fclift@verio.net> for testing this on alpha.
Tested on: i386, ia64, alpha
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
is enabled when both the size of bus_addr_t > 4 and the card claims support.
Don't wake up the kthread to allocate more commands if we know that we've
already allocated the max number of commands.
function.
Also, use m_defrag where appropriate to defrag long mbuf chains
in the same fashion as was done in if_sis.c. Before this change,
if_dc would blow up and take down the interface if fed a really long
mbuf chain.
MFC after: 2 weeks
Clean up the DMA interface too much unneeded stuff crept in with
the busdma code back when.
Modify the ATA_IN* / ATA_OUT* macros so that resource and offset
are gotten from a table. That allows for new chipsets that doesn't
nessesarily have things ordered the good old way. This also removes
the need for the wierd PC98 resource functions.
Tested on: i386, PC98, Alpha, Sparc64
the adapter from becoming wedged when when the interface is
is brought up by ether_ioctl() (when you set an IP address for example.)
Confirmed this "fix" from NetBSD's i82586 backend. It seems hackish
to me but whatever.
- Sanitize dpt_alloc().
- Add helper functions for resource alloc/release.
- Add detach method.
- Relocate definition of devclass_t.
- Move some debugging output behind bootverbose.
- Implement an identify method for ISA devices
but don't use it right now.
- Add data structuress for doing 64-bit scatter/gather
- Move busdma tag creations around so that only the parent is
created in aac_pci.c.
- Retrieve the capabilities word from the firmware before setting
up command structures and tags. This allows the driver to decide
whether to do 64-bit commands, and if work-arounds are needed for
systems with >2GB of RAM.
- Only enable the SCSI passthrough if it's enabled in the capabilities
word in the firmware.
This should fix problems with the 2120S and 2200S cards in systems with more
than 2GB of RAM. Full 64-bit support is forthcoming.
MFC-After: 1 week
and be prepared to wait much longer for codec to become ready.
Credit to Hugo D. Valentim <hvalentim@gmx.net> for reporting the
problem, providing useful pointers, and repeated diff testing.
channel and disable DXS3. Several users have reported DXS3 as playing
at half speed on the 8233A revision of the chipset. This implicitly
means no SPDIF for VIA8233A users.
The former fakes a valid response to an inquiry command. (I am completely
blown away that there are devices which hang upon receiving inquiry). The
latter returns "invalid request" to any inquiry commands with EVPD set.
NO_INQUIRY implies NO_INQUIRY_EVPD but not vice versa. Both quirks have been
tested separately on my USB key although it didn't require either of them.
While I'm here, fix wildcarding so that any/all of vendor, product, revision
can be wildcarded.
Idea from: Linux
MFC after: 2 weeks
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
Otherwise sysbeep() makes an annoying clicking sound on some systems.
'kbdcontrol -b off' just sets the duration and pitch to zero, it doesn't
set the QUIET_BELL flag.
Tested by: SorAlx <soralx@cydem.zp.ua>
PR: misc/41772
MFC after: 1 week
- Clear PCIM_CMD_MWRICEN:
some chips seem to have problem with write invalidate.
clearing this bit fixes SBP timeout problem.
Tested by: Michael Reifenberger <Michael.Reifenberger@Plaut.de>
- Set PCIM_CMD_SERRESPEN and PCIM_CMD_PERRESPEN
- Moderate value for latency timer.
Change 27224 by imp@imp_hammer on 2003/03/22 00:16:22
Put what I think are the correct TX RATE translation tables
in place for LUCENT firmware. This is based on the 4.x driver.
Maybe it should be table driven?
ifconfig wi0 media DS/11Mbps still fails, but it fails before
we even get to the txrate stuff, so other things are wrong.
Change 27225 by imp@imp_hammer on 2003/03/22 00:45:11
Default ic_fixed_rate to -1. This is the same thing as autoselect.
There really should be a #define for this...
- Use it in atacontrol(8) when listing ATA devices instead of
stopping at the first ENXIO received.
This makes atacontrol list work on my sparc64 where the two ATA
channels I have are numbered 2 and 3.
Reviewed by: sos
one tx buffer for these cards. The old driver only used one. We use
1 for symbol, and 3 for prism cards.
o Don't do the maximum loops thing in the ISR. In fact, revert to the
old interrupt handler. Lucent cards don't seem to work too well if
you don't disable/enable interrupts from the card in the ISR.
Between these two changes, Lucent cards suck less. They work in
autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a
specific media speed doesn't work, and I've had a few issues even with
these patches. They turn a former brick into a nearly useful card.
These patches work on the prism 2 and 2.5 PC Card cards that I have.
I've not tested this on PCI cards. I suspect, but couldn't find
proof, that they were the reason that the ISR was changed so radically
from its FreeBSD roots in NetBSD. We might need to have a variant ISR
if so.
code both seem to call wi_start (directly or via the if_start pointer)
without checking to see if OACTIVE is 0. In addition, I think that
with the use of 3 transmit buffers this routine can be called with
OACTIVE set, but I might be mistaken about that (and it doesn't
matter).
Reviewed by: sam
Noticed by: imp, alfred, ambrisko
now unnecessary hack from the previous commit;
- Add support for Interrupt Latch Register (ILR) into puc(4). So far only
ILRs compatible with specifications from Digi International are supported.
Support for other types of ILRs could be easily added later;
- Correct clock frequency for IC Book Labs Dreadnought x16 Lite board;
- Enable ILR detection/usage for IC Book Labs Dreadnought x16 boards.
Sponsored by: IC Book Labs
MFC after: 2 weeks
this card is based on 16750 UART, modify sio(4) a bit to ignore 16750-specific
7th bit of MCR when probing card. This allows card to be detected and attached
as 16550A-compatible device. More work needs to be done in order to enable
nice 16750-specific features such as larger fifo buffer and higher speeds.
Sponsored by: IC Book Labs
MFC after: 2 weeks
Harti Brandt's effort.
remove the DMA test to detect problems of the first generation PCI chipsets
back in 1998.
it is no longer needed and has been the source of the false alarm that
the driver uses too much stack space.
monitors the entropy data harvested by crypto drivers to verify it complies
with FIPS 140-2. If data fails any test then the driver discards it and
commences continuous testing of harvested data until it is deemed ok.
Results are collected in a statistics block and, optionally, reported on
the console. In normal use the overhead associated with this driver is
not noticeable.
Note that drivers must (currently) be compiled specially to enable use.
Obtained from: original code by Jason L. Wright
conditional in each driver on foo_RNDTEST being defined_
o bring HIFN_DEBUG and UBSEC_DEBUG out to be visible options; they control
the debugging printfs that are set with hw.foo.debug (e.g. hw.hifn.debug)
attach routine, calling WIUNLOCK in the error case of one of the ifs
for that routine is now bogus. This should have been removed when the
WILOCK() was removed, but wasn't.
Submitted by: "Harti Brandt" <brandt@fokus.fraunhofer.de>
it is expected that they will not be enabled at the time that it
is called. This is reported to work around a problem in RELENG_4
where the kernel panics on boot if FAST_IPSEC and crypto support
are enabled.
Tested by: Scott Johnson <scottj@insane.com>
use the underlying AsahiOptical USB chip and thus this quirk may need to
be generalized in the future.
PR: kern/46369
Submitted by: Tim Vanderhoek <vanderh@ecf.utoronto.ca>
MFC After: 3 days
like secure level but which restricts changes to the keymap. Its
values impose the following restrictions:
0: No restriction - this is the default.
1: Only root can change restricted keys (like boot, panic, ...)
2: Only root can change restricted keys and regular keys.
Other users still can change accents and function keys.
3: Only root can change restricted keys, regular keys and accents.
4: Only root can change any of the keymap (restricted keys, regular
keys, accents and function keys).
Unfortunately, the keyboard's accent map is cleared when a new keymap
is loaded, which makes the distinction between level 3 and level 4
less useful.
The MAC guys might like to make this a policy?
No objections from: -audit about 6 moths ago
is more robust and prevents the hijacking of /dev/console for the typical
mistake.
Remove unneeded MAJOR_AUTO uses, it is only needed explicitly now if the
driver source has cross-branch compatibility to old releases.
included in XFree86 4.3, but includes some fixes. Notable changes include
Radeon 8500-9100 support, PCI Radeon/Rage 128 support, transform & lighting
support for Radeons, and vblank syncing support for r128, radeon, and mga.
The gamma driver was removed due to lack of any users.
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
Include read streaming in the PPR flags we display in diagnostics.
In ahd_reset(), set the known mode after our initial pause prior to
setting the mode. We can't just set the mode directly because the
current mode, after the pause, is most likely unknown and setting the
mode when the saved mode is unknown will trigger an assertion in
the mode debug code.
Complete an audit for SCB RAM reads. These reads must be performed
via the special ahd_in?_scbram() methods so we can perform a
Rev A. PCI-X workaround.
Remove a superfluous mode save operation that was performed just
prior to a call to ahd_clear_critical_section(). The saved mode
was never restored and wouldn't have been valid anyway since the
mode could change while single stepping out of a critical section.
aic79xx.h:
Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG.
aic79xx_inline.h:
Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG
and only apply the workaround if this bug is active. The old code
applied the workaround in all cases.
aic79xx_pci.c:
Set AHD_PCIX_SCBRAM_RD_BUG for the A4.
Remove an attempted saved_modes call in ahd_pci_test_register_access().
Saving the modes can only occur when we are paused, but the call was
happening before the chip was known to be paused. Restoring the
modes doesn't make sense either since the code makes no assumptions
about the state of the sequencer until the first time the mode is set
by the driver. This happens after the registers are successfully
mapped.
Submitted by Hiroyuki Aizu <eyes@navi.org>
(refer to [FreeBSD-users-jp 65061])
Tested by Hiroharu Tamaru <tamaru@myn.rcast.u-tokyo.ac.jp>
(refer to [bsd-usb:689])
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
This should fix some problem of SBP2 device probing.
Prior to rev 1.41, we keep writing the register while bus reset phase.
But in rev 1.41, we ignore successive bus reset events and some chips seem to
clear the register after we write to it.
Tested by: Michael Reifenberger <root@nihil.reifenberger.com>
Clear the LQICRC_NLQ status should it pop up after we have
already handled the SCSIPERR. During some streaming operations
this status can be delayed until the stream ends. Without this
change, the driver would complain about a "Missing case in
ahd_handle_scsiint".
In the LQOBUSFREE handler...
Don't return the LQOMGR back to the idle state until after
we have cleaned up ENSELO and any status related to this
selection. The last thing we need is the LQO manager starting
another select-out before we have updated the execution queue.
It is not clear whether the LQOMGR would, or would not
start a new selection early.
Make sure ENSELO is off prior to clearing SELDO by flushing
device writes.
Move assignment of the next target SCB pointer inside of
an if to make the code clearer. The effect is the same.
Dump card state in both "Unexpected PKT busfree" paths.
In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
That register only exists in the SCSI mode. Also set the mode
explicitly to the SCSI mode after chip reset due to paranoia.
Re-arrange code so that SXFRCTL1 is restored as quickly after the
chip reset as possible.
S/G structurs must be 8byte aligned. Make this official by saying
so in our DMA tag.
Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
true. This can cause a CIO bus lockup if a PCI or PCI-X error
occurs while the stretch is occurring - the host cannot service
the PCI-X error since the CIO bus is locked out and SHVALID will
never resolve. The stretch was added in the Rev B to simplify the
wait for SHVALID to resolve, but the code to do this in the open
source sequencer is so simple it was never removed.
Consistently use MAX_OFFSET for the user max syncrate set from
non-volatile storage. This ensures that the offset does not
conflict with AH?_OFFSET_UNKNOWN.
Have ahd_pause_and_flushwork set the mode to ensure that it has
access to the registers it checks. Also modify the checking of
intstat so that the check against 0xFF can actually succeed if
the INT_PEND mask is something other than 0xFF. Although there
are no cardbus U320 controllers, this check may be needed to
recover from a hot-plug PCI removal that occurs without informing
the driver.
Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes
an infinite loop at card initialization if the cacheline size is 0.
aic79xx.h:
Add AHD_EARLY_REQ_BUG bug flag.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the
curr->offset can never be, unlike '0' which we previously used.
This fixes code that only checks for a non-zero offset to
determine if a sync negotiation is required since it will fire
in the unknown case even if the goal is async.
aic79xx.reg:
Add comments for LQISTAT bits indicating their names in the 7902
data book. We use slightly different and more descriptive names
in the firmware.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
aic79xx.seq:
Update comments regarding rundown of the GSFIFO to reflect reality.
Fix spelling errors.
Since we use an 8byte address and 1 byte length, shorten the size
of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.
Remove code that, assuming the abort pending feature worked, would
set MK_MESSAGE in the SCB's control byte on completion to catch
invalid reselections. Since we don't see interrupts for completed
selections, this status update could occur prior to us noticing the
SELDO. The "select-out" queue logic will get confused by the
MK_MESSAGE bit being set as this is used to catch packatized
connections where we select-out with ATN. Since the abort pending
feature doesn't work on any released controllers yet, this code was
never executed.
Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ
assertions just because they were asserted within the bus settle delay
window. This allows us to tolerate devices like the GEM318 that
violate the SCSI spec.
Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit
should have no effect, but who knows...
On the Rev A, we must wait for HDMAENACK before loading additional
segments to avoid clobbering the address of the first segment in
the S/G FIFO. This resolves data-corruption issues with certain
IBM (now Hitachi) and Fujitsu U320 drives.
Rearrange calc_residual to avoid an extra jmp instruction.
On RevA Silicon, if the target returns us to data-out after we
have already trained for data-out, it is possible for us to
transition the free running clock to data-valid before the required
100ns P1 setup time (8 P1 assertions in fast-160 mode). This will
only happen if this L-Q is a continuation of a data transfer for
which we have already prefetched data into our FIFO (LQ/Data
followed by LQ/Data for the same write transaction). This can
cause some target implementations to miss the first few data
transfers on the bus. We detect this situation by noticing that
this is the first data transfer after an LQ (LQIWORKONLQ true),
that the data transfer is a continuation of a transfer already
setup in our FIFO (SAVEPTRS interrupt), and that the transaction
is a write (DIRECTION set in DFCNTRL). The delay is performed by
disabling SCSIEN until we see the first REQ from the target.
Only compile in snapshot savepointers handler for RevA silicon
where it is enabled.
Handle the cfg4icmd packetized interrupt. We just need to load
the address and count, start the DMA, and CLRCHN once the transfer
is complete.
Fix an oversight in the overrun handler for packetized status
operations. We need to wait for either CTXTDONE or an overrun
when checking for an overrun. The previous code did not wait
and thus could decide that no overrun had occurred even though
an overrun will occur on the next data-valid req. Add some
comment to this section for clarity.
Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
completion in the packetized status case. LASTSDONE may come up
more quickly since it only records completion on the SCSI side,
but since LAST_SEG_DONE is used everywhere else (and needs to be),
this is less confusing.
Add a missing invalidation of the longjmp address in the non-pack
handler. This code needs additional review.
aic79xx_inline.h:
Fix spelling error.
aic79xx_osm.c:
Set the cdb length for CDBs dma'ed from host memory.
Add a comment indicating that, should CAM start supporting cdbs
larger than 16bytes, the driver could store the CDB in the status
buffer.
aic79xx_pci.c:
Add a table entry for the 39320A.
Added a missing comma to an error string table.
Fix spelling errors.
Move <sys/conf.h> before <sys/disk.h>.
No need for raidread()/raidwrite(), we have generic code for that.
Remove non-functional dump code.
Make raidinit() return the softc, not the dev_t.
Move to "struct disk*" centric API.
Fix printfs' to get name from struct disk instead of dev_t.
OK'ed by: scottl
don't end up freezing the box. This makes VTY locking useless
in the DDB case but a box which is supposed to be physically
secure shouldn't compile DDB anyway.
Reviewed by: silence on -audit
Improve SBP device probeing:
- Wait 2 sec before issuing LOGIN ORB expecting the reconnection
hold timer expires.
- Serialize management ORB and scanning LUN by CAM on each target.
This should fix the problem for devices which have multiple LUNs.
Test device is donated by: Jaye Mathisen <mrcpu@internetcds.com>
- Freeze SIM queue for 2 sec after BUS RESET.
- Retry with LOGIN rather than RECONNECT after LOGIN is not completed for
BUS RESET.
- Use appropriate CAM status for BUS RESET and DEVICE RESET.
- Let CAM to scan targets after BUS REST.
- Implement CAM scan target function.
- Keep our own devq freeze count.
- Let CAM to know that SBP does tagged queuing.
These should be merged to RELENG_4 before 4.8-RELEASE.
a correctly aligned address in this block we really want to check, that the
part of the chunk that starts at the aligned address is large enough with
regard to the original request. Comparing it to 0 makes no sense, because this
is always true except in the rare case, that the aligned address is just at
the end of the chunk.
Approved by: jake (mentor)
the fxp driver. This is enabled only for the 82550/82551 chips
(PCI revision code 12 or 13). RX and TX checksum offload are
both supported. Transmit offload is limited to TCP and UDP only
right now: there seems to be a problem with IP header checksumming
on transmit in some cases.
This chip has hardware VLAN support as well. I hope to enable
support for this eventually.
- the mutex aac_io_lock protects the main codepaths which handle queues and
hardware registers. Only one acquire/release is done in the top-half and
the taskqueue. This mutex also applies to the userland command path and
CAM data path.
- Move the taskqueue to the new Giant-free version.
- Register the disk device with DISKFLAG_NOGIANT so the top-half processing
runs without Giant.
- Move the dynamic command allocator to the worker thread to avoid locking
issues with bus_dmamem_alloc().
This gives about 20% improvement in most of my benchmarks.
turns runs its tasks free of Giant too. It is intended that as drivers
become locked down, they will move out of the old, Giant-bound taskqueue
and into this new one. The old taskqueue has been renamed to
taskqueue_swi_giant, and the new one keeps the name taskqueue_swi.
- Remove the buftimelock mutex and acquire the buf's interlock to protect
these fields instead.
- Hold the vnode interlock while locking bufs on the clean/dirty queues.
This reduces some cases from one BUF_LOCK with a LK_NOWAIT and another
BUF_LOCK with a LK_TIMEFAIL to a single lock.
Reviewed by: arch, mckusick
- Get rid of the useless atop() / pmap_phys_address() detour. The
device mmap handlers must now give back the physical address
without atop()'ing it.
- Don't borrow the physical address of the mapping in the returned
int. Now we properly pass a vm_offset_t * and expect it to be
filled by the mmap handler when the mapping was successful. The
mmap handler must now return 0 when successful, any other value
is considered as an error. Previously, returning -1 was the only
way to fail. This change thus accidentally fixes some devices
which were bogusly returning errno constants which would have been
considered as addresses by the device pager.
- Garbage collect the poorly named pmap_phys_address() now that it's
no longer used.
- Convert all the d_mmap_t consumers to the new API.
I'm still not sure wheter we need a __FreeBSD_version bump for this,
since and we didn't guarantee API/ABI stability until 5.1-RELEASE.
Discussed with: alc, phk, jake
Reviewed by: peter
Compile-tested on: LINT (i386), GENERIC (alpha and sparc64)
Runtime-tested on: i386
flag that can be marked on each symmetric op
o eliminate hw.ubsec.maxbatch and hw.ubsec.maxaggr since they are not
needed anymore
o change ubsec_feed to return void instead of int since zero is always
returned and noone ever looked at the return value
Reading the PCI config space with the wrong (larger) size is not
a problem in this case, but writing can be as it clobbers unrelated
registers. In this case the clobbering is for reserved fields, which
too is mostly harmless... for now. Hence, this change is mostly
preventive in nature.
without waiting, since they are called from a system-call context only.
This appears to fix all sorts of problems with open("/dev/dsp", O_WRONLY)
randomly returning ENXIO.
Found by: cognet
