that are apparently misconfigured by the manufacturer and cause the mapping
logic to fail. The fallback allows drive numbers to be assigned based on the
PHY number that they're attached to. Add sysctls and tunables to overrid
this new behavior, but they should be considered only necessary for debugging.
Reviewed by: imp, smh
Obtained from: Netflix
MFC after: 3 days
Sponsored by: D8403
While I'm here, move message status codes to hv_utilreg.h, since they
will be used by the upcoming VSS stuffs.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8391
With guest trackpoint present trackpoint probing switched synaptics
device to absolute mode with different protocol instead of keeping it
in relative mode.
PR: 213757
Submitted by: Vladimir Kondratyev <wulf@cicgroup.ru>
MFC after: 1 week
Summary:
i.MX5 and PowerPC use a very similar eSDHC controller, which is also
similar to the uSDHC controller used by i.MX6. The imx_sdhci driver works
almost completely with PowerPC, with some minor tweaks.
There is one caveat with this: reset currently does not work on PowerPC, so has
been #ifdef'd out until this can be tracked down and fixed. If resets are done
the controller will timeout all data transactions. Without a reset, it appears
to work just fine.
This is part 3, following up r308186 and r308187.
Test Plan:
This has been tested on a PowerPC QorIQ P1022 board. It has not been
tested on i.MX, but no regressions are expected.
Reviewed By: imp
Differential Revision: https://reviews.freebsd.org/D8407
Some controllers (namely Freescale's eSDHC, tested) will continue to assert
the card removed or card insert interrupts even after being handled. To work
around this, disable watching the interrupt that just occurred until the
opposite interrupt is triggered.
Linux has a similar change in its driver to address the same problem.
* Starting a scan from wpa_supplicant or via ifconfig while associated,
should no longer cause firmware panics or abort early.
Tested:
* AC7260, STA mode
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8412
* SYNC_RESP_STRUCT and SYNC_RESP_PTR originate from the OpenBSD version of
iwm, and they weren't serving any real purpose in the FreeBSD port.
* We just do a single bus_dmamap_sync for syncing the complete received frame,
instead of explicitly bus_dmamap_sync-ing subranges of the frame like in
the OpenBSD iwm code.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7939
This allows us to make strong assertions about descriptor address
validity. Additionally, future generations of the ioat(4) hardware will
require contiguous descriptors.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
This paves the way for a contiguous descriptor array.
A contiguous descriptor array has the benefit that we can make strong
assertions about whether an address is a valid descriptor or not. The
other benefit is that future generations of I/OAT hardware will require
a contiguous descriptor array anyway. The downside is that after system
boot, big chunks of contiguous memory is much harder to find. So
dynamic scaling after boot is basically impossible.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
And put them under HN_IFSTART_SUPPORT, which is by default on until
we whack the if_start related bits from base system.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8392
Upstream the BUF_TRACKING and FULL_BUF_TRACKING buffer debugging code.
This can be handy in tracking down what code touched hung bios and bufs
last. The full history is especially useful, but adds enough bloat that
it shouldn't be enabled in release builds.
Function names (or arbitrary string constants) are tracked in a
fixed-size ring in bufs. Bios gain a pointer to the upper buf for
tracking. SCSI CCBs gain a pointer to the upper bio for tracking.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8366
A grant-table user-space device will allow user-space applications to map
and share grants (Xen way to share memory) among Xen domains. This grant
table user-space device has been tested with the QEMU Qdisk Xen backed.
Submitted by: jaggi
Reviewed by: royger
Differential review: https://reviews.freebsd.org/D7293
- Move the SYSINIT to DRIVER/SECOND, i.e. after the vm_guest becomes
determistic.
- Minor style changes.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8370
Mainly because the host side only set TCPCS and IPCS even for
UDP datagrams.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8369
And use large default temporary channel packer buffer; we really
don't want it to be expanded at run time.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8367
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
It is possible that wrmsr in amd_stop_pmc() causes an overflow in a counter
that it disables. In that case a non-maskable interrupt is generated. The
interrupt handler code was written in such a way that it would re-enable the
counter. That would lead to an unexpected interrupt later on.
This problem was easy to reproduce with
$ pmcstat -T -P instructions -t $pid
if the target process is sufficiently busy and there are context switches from
time to time. There would be a lot of interrupts to "race" with amd_stop_pmc()
called during the context switches. The problem affected only AMD processors.
While there, trace whether amd_intr() claimed an interrupt.
Reviewed by: jhb
MFC after: 2 weeks
The CHANSTS register is a split 64-bit register on CBDMA units before
hardware v3.3. If a torn read happens during ioat_process_events(),
software cannot know when to stop completing descriptors correctly.
So, just use the device-pushed main memory channel status instead.
Remove the ioat_get_active() seatbelt as well. It does nothing if the
completion address is valid.
Sponsored by: Dell EMC Isilon
There are 4 independent knobs in T5+ chips to include or exclude PAUSE
frames from the "total frames" and "multicast frames" counters in either
direction. This change lets the driver deal with any combination of
these settings.
but never released. Since no real hardware was released with this ID,
just drop it from the aacraid driver. This paves the path for future
drivers for hardware that actually has this ID.
Submitted by: Scott Benesh from Microsemi.
Differential Revision: https://reviews.freebsd.org/D8377
MFC After: 3 days
we have to refresh it ... always. This fixes problems reported in NetMap
with em(4) devices after conversion to extended descriptor format in
svn r293331.
Submitted by: luigi@
Reported by: franco@opnsense.org
MFC after: 2 days
- use PCI_VENDOR and PCI_DEVICE ids from a publicly allocated range
(thanks to RedHat)
- export memory pool information through PCI registers
- improve mechanism for configuring passthrough on different hypervisors
Code is from Vincenzo Maffione as a follow up to his GSOC work.
This paves way for more chimney sending buffer reorganization.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8343
And use it for vmbus channel logging, which can log the channel
owner's name properly, instead of vmbus0.
Submitted by: QianYue You <t-youqi microsoft com>
MFC after: 1 week
Sponsored by: Microsoft
The directly following m_defrag() call can wait, so there is no reason this
call can't as well.
Reported by: Coverity
CID: 1353551
Sponsored by: Dell EMC Isilon
contiguous regions in an mbuf chain.
If the payload of an mbuf ends at a page boundary count_mbuf_nsegs would
incorrectly consider the next mbuf's payload physically contiguous based
solely on a KVA comparison.
MFC after: 1 week
Sponsored by: Chelsio Communications
Link status check is much more lightweight than network change detection.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8311
This will not happen in real world, since TX consumption of the vmbus
TX bufring is limitted. Better safe than sorry.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8309
All RNDIS control messages have used SG list for a while. This makes
the send context suitable for further refactoring.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8308
- Use ums lock as evdev lock
- Do not cap axes values to sysmouse limits for evdev reports
- Do not map T-axis events to buttons for evdev reports
- Use shortcuts for event reporting
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Add wrappers around generic evdev_push_event for specific event types:
EV_KEY/EV_REL/EV_ABS etc...
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
If the device tree doesn't contain a cpu-handle field in any bman-portal or
qman-portal, it will exit without setting up the devinfo, leaving it
uninitialized. This will lead to attempts to free random memory, and ultimately
panic.
Currently the network change is simulated by link status changes.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8295
Instead replace it with a different hack, that turns fman into a simplebus
subclass, and maps its children within its address space.
Since all PHY communication is done through dtsec0's mdio space, the FDT
contains a reference to the dtsec0 mdio handle in all nodes that need it.
Instead of using Freescale's implementation for MII access, use our own (copied
loosely from the eTSEC driver, and could possibly be merged eventually). This
lets us access the registers directly rather than needing a full dtsec interface
just to access the registers.
Future directions will include turning fman into more of a simplebus, and not
mapping the region and playing games. This will require changes to the dtsec
driver to make it a child of fman, and possibly other drivers as well.
host-programmed DMA regions. This change seemingly fixes the
descriptor fetches, but the packet memory accesses are left
problematic.
Reviewed by: emaste, erj, sbruno
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8282
fastpath and slowpath taskqueues.
2. Service all transmits in taskqueue threads.
3. additional stats counters for keeping track of
- bd availability
- tx buf ring not emptied in the fp task queue.
These are drained via timeout taskqueue.
- tx attempts during link down.
MFC after: 5 days
fix build on 32 bit platforms
simplify logic in netmap_virt.h
The commands (in net/netmap.h) to configure communication with the
hypervisor may be revised soon.
At the moment they are unused so this will not be a change of API.
As part of an effort to extend Book-E to the 64-bit world, make the necessary
changes to the DPAA/dTSEC driver set to be integer-pointer conversion clean.
This means no more casts to int, and use uintptr_t where needed.
Since the NCSW source is effectively obsolete, direct changes to the source tree
are safe.
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
When detaching device trees parent devices must be detached prior to
detaching its children. This is because parent devices can have
pointers to the child devices in their softcs which are not
invalidated by device_delete_child(). This can cause use after free
issues and panic().
Device drivers implementing trees, must ensure its detach function
detaches or deletes all its children before returning.
While at it remove now redundant device_detach() calls before
device_delete_child() and device_delete_children(), mostly in
the USB controller drivers.
Tested by: Jan Henrik Sylvester <me@janh.de>
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8070
MFC after: 2 weeks
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
Split efirt.ko initialization into early stage where runtime services
KPI environment is created, to be used e.g. for RTC, and the later
devfs node creation stage, per module.
Switch the efi device to use make_dev_s(9) instead of make_dev(9). At
least, this gracefully handles the duplicated device name issue.
Remove ARGSUSED comment from efidev_ioctl(), all unused arguments are
annotated with __unused attribute.
Reported by: ambrisko, O. Hartmann <ohartman@zedat.fu-berlin.de>
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Comparing to the Linux driver there is still one missing feature.
The Linux driver finds and enables "Embedded Controller" item in
the 0x11 group if it's not enabled yet.
I tested the new method, Torfinn Ingolfsen tested the old method
and helped to fix several bugs in the earlier versions of the patch.
Tested by: Torfinn Ingolfsen <torfinn.ingolfsen@getmail.no>
Reviewed by: rpaulo
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D8227
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Reported by: Lili Deng <v-lide microsoft com>
MFC after: 3 days
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8238
Suppose that we have an exclusively busy page, and a thread which can
accept shared-busy page. In this case, typical code waiting for the
page xbusy state to pass is
again:
VM_OBJECT_WLOCK(object);
...
if (vm_page_xbusied(m)) {
vm_page_lock(m);
VM_OBJECT_WUNLOCK(object); <---1
vm_page_busy_sleep(p, "vmopax");
goto again;
}
Suppose that the xbusy state owner locked the object, unbusied the
page and unlocked the object after we are at the line [1], but before we
executed the load of the busy_lock word in vm_page_busy_sleep(). If it
happens that there is still no waiters recorded for the busy state,
the xbusy owner did not acquired the page lock, so it proceeded.
More, suppose that some other thread happen to share-busy the page
after xbusy state was relinquished but before the m->busy_lock is read
in vm_page_busy_sleep(). Again, that thread only needs vm_object lock
to proceed. Then, vm_page_busy_sleep() reads busy_lock value equal to
the VPB_SHARERS_WORD(1).
In this case, all tests in vm_page_busy_sleep(9) pass and we are going
to sleep, despite the page being share-busied.
Update check for m->busy_lock == VPB_UNBUSIED in vm_page_busy_sleep(9)
to also accept shared-busy state if we only wait for the xbusy state to
pass.
Merge sequential if()s with the same 'then' clause in
vm_page_busy_sleep().
Note that the current code does not share-busy pages from parallel
threads, the only way to have more that one sbusy owner is right now
is to recurse.
Reported and tested by: pho (previous version)
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D8196
Previously the driver used more low level operations like iicbus_start
and iicbus_write. The problem is that those operations are not
implemented by iicbus(4) and the calls were effectively routed to
a driver to which the bus is attached.
But not all of the controllers implement such low level operations
while all of the drivers are expected to have iicbus_transfer.
While there fix incorrect implementation of iicsmb_bwrite and iicsmb_bread.
The former should send a byte count before the actual bytes, while the
latter should first receive the byte count and then receive the bytes.
I have tested only these commands:
- quick (r/w)
- send byte
- receive byte
- read byte
- write byte
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8170
with no creative content. Include "lost" changes from git:
o Use /dev/efi instead of /dev/efidev
o Remove redundant NULL checks.
Submitted by: kib@, dim@, zbb@, emaste@
to ieee80211_add_rx_params() + drop last (ieee80211_rx_stats) parameter
Note: there is an additional check for ieee80211_get_rx_params()
return value (which does not exist in the original diff).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8207
- If check for net,ethernet/usb,device compatible node fails, try to find
.../usb/hub/ethernet, where ... is bus path that can depend on actual HW.
net,ethernet/usb,device compatibity strings are FreeBSD custom invention
that is used only in RPi DTBs and since there is no other way to tie USB
device to FDT node we just do our best effort here to work with upstream
device tree
- Use -1 value to indicate invalid phandle_t, 0 is valid phandle value and
shouldn't be used as error signal
This will allow to add slave drivers in the same fashion as for iicbus.
Also, allow other code to add a child device and set its 'addr' ivar.
The ivar can only be set if it's unset, it can not be changed.
That could be used, for example, by a platform driver that has
a precise description of the hardware and, thus, knows what drivers
can handle what slaves.
The slave auto-probing code is unsafe and broken because it uses
7-bit slave addresses. It's going to be removed.
Note: internally the driver uses address of zero as an unset address
while smbus_get_addr() returns it as -1 for compatibility reasons.
The address is expected to be unset only for children that do not
work with slaves like, for example, smb(4).
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8173
This should have been committed in r307093: resource allocation depends
on source of the device tree. upstream dts has extra interrupt that we can
ignore
userland. It supports userland interfaces to UEFI Runtime Services. This is
indended to the the MI portion of EFI RuntimeServices support.
Differential Revision: https://reviews.freebsd.org/D8128
Reviewed by: kib@, wblock@, Ganael Laplanche
Extend the mapping table for external port numbering to support port modes
which output to the second external port only. Where supported, map from
the current port mode rather than inferring from all the available modes.
Updated comments for clarity.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D8210
This is the preamble for network device SR-IOV and
NDIS_STATUS_NETWORK_CHANGE handling.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8209
It fixes driver attach issue to a new firmware which reports a new
port-modes.
Reviewed by: gnn
Submitted by: Tom Millington <tmillington at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D8203
The _correct_ way to identify the supported checksum offloading and
TSO parameters is to query OID_TCP_OFFLOAD_HARDWARE_CAPABILITIES.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8088
ieee80211_tx_complete()
This change allows to pass packet length to rate control modules and
fixes IFCOUNTER_OBYTES calculation.
Tested with Intel 3945BG, STA mode.
Automaticaly release (send ABS_MT_TRACKING_ID = -1) MT-slots
that has not been listed in current MT protocol type B report.
Slot is counted as listed if corresponding ABS_MT_SLOT event
has been sent regardless of other MT events.
Events are sent on SYN_REPORT event.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Add new API call: evdev_register_mtx which takes lock argument that
should be used instead of internal one for evdev locking. Useful for
cases if evdev_push_event() is always called with driver's lock taken
and reduces amount of lock aquisitions. This allows to avoid LOR
between ev_open/ev_close invocations and evdev_push_event() Such LOR
can happen when ev_open/ev_close methods acquire driver lock and
evdev_push_event() is called with this lock taken.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
There are a variety of more interesting RX statistics that we should
keep track of but we don't. This is a starting point for adding more
information.
Specifically:
* now the RX rate information and some of the packet status is
passed up;
* The 32 bit or 64 bit TSF is passed up;
* the PHY mode is passed up;
* the "I'm decap'ed AMSDU!" state is passed up;
* number of RX chains is bumped to 4.
This is all mostly a placeholder for getting the data into the RX status
before we pass it up to net80211 - unfortunately we don't yet enforce
that drivers provide it, nor do we pass the provided info back up the
stack so anyone can use the data.
We're going to need to use some of this data moving forward.
Notably, now that some hardware can do AMSDU decap for us (the intel iwm
driver can do it when we flip it on; the ath10k port I'm doing does
it for us) then we need to pass it up through the stack so the duplicate
RX sequence numbers and crypto/IV details don't cause the packet to
be dropped and/or counted against a replay counter.
It's also the beginning of being able to do more interesting node
accounting in net80211. Specifically, once drivers start populating
per-packet rate information, AMPDU information, timestamps, etc,
we can start providing histograms of rate-versus-RSSI, account
for receive time spent per node and other such interesting things.
(Note: I'm also hoping to include ranging and RTT information for
future chipset support; and it's likely going to include it in
this kind of fashion.)
netmap_kern.h currently requires all drivers including it to include
selinfo.h.
Submitted by: mmacy@nextbsd.org
Reviewed by: gnn
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D5334
Replace various void * / int argument combinations with common structures:
- ieee80211_ratectl_tx_status for *_tx_complete();
- ieee80211_ratectl_tx_stats for *_tx_update();
While here, improve amrr_tx_update() for a bit:
1. In case, if receiver is not known (typical for Ralink USB drivers),
refresh Tx rate for all nodes on the interface.
2. There was a misuse:
- otus(4) sends non-decreasing counters (as originally intended);
- but ural(4), rum(4) and run(4) are using 'read & clear' registers
to obtain statistics for some period of time (and those 'last period'
values are used as arguments for tx_update()). If arguments are not big
enough, they are just discarded after the next call.
Fix: move counting into *_tx_update()
(now otus(4) will zero out all node counters after every tx_update() call)
Tested with:
- Intel 3945BG (wpi(4)), STA mode.
- WUSB54GC (rum(4)), STA / HOSTAP mode.
- RTL8188EU (urtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8037
- Convert "options EVDEV" to "device evdev" and "device uinput", add
modules for both new devices. They are isolated subsystems and do not
require any compile-time changes to general kernel subsytems
- For hybrid drivers that have evdev as an optional way to deliver input
events add option EVDEV_SUPPORT. Update all existing hybrid drivers
to use it instead of EVDEV
- Remove no-op DECLARE_MODULE in evdev, it's not required, MODULE_VERSION
is enough
- Add evdev module dependency to uinput
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
On ARM if memattr is not overriden mmap(2) maps framebuffer
memory as WBWA which means part of changes to content in userland
end up in cache and appear on screen gradually as cache lines are
evicted. This change adds configurable memattr that hardware fb
implementation can set to get the memory mapping type it
requires:
- Add new flag FB_FLAG_MEMATTR that indicates that framebuffer
driver overrides default memattr
- Add new field fb_memattr to struct fb_info to specify requested
memattr
Reviewed by: ray
Differential Revision: https://reviews.freebsd.org/D8064
Prepare for making evdev a module. "Pure" evdev device drivers (like
touchscreen) and evdev itself can be built as a modules regardless of
"options EVDEV" in kernel config. So if people does not require evdev
functionality in hybrid drivers like ums and ukbd they can, for instance,
kldload evdev and utouchscreen to run FreeBSD in kiosk mode.
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
- Replace tunables-only hw.psm.synaptics_support, hw.psm.trackpoint_support,
and hw.psm.elantech_support with respective sysctls declared with
CTLFLAG_TUN. It simplifies checking them in userland, also makes them
easier to get discovered by user
- Get rid of debug.psm.loglevel and hw.psm.tap_enabled TUNABLE_INT
declaration by adding CTLFLAG_TUN to read/write sysctls that were
already declared for these tunables.
Suggested by: jhb
Summary:
NXP/Freescale, among others, includes an optional cell-index property
on nodes to denote the SoC block number of the node. This can be useful if, for
example, a node is disabled or nonexistent in the fdt, or the blocks are not
organized in address-sorted order. For instance, on the P1022, DMA2 is located
at CCSR offset 0xC000, while DMA1 is located at 0x21000.
Reviewed By: jmcneill
Differential Revision: https://reviews.freebsd.org/D8054
This prepares to consolidate hn_stop() and netvsc_detach().
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8055
- The original 'disengage' ATA controller model does not work properly
for all possible disk configurations. Use the newly added ATA disk
veto eventhandler to fit into all possible disk configuration.
- If the 'invalid LUN' happens on blkvsc controllers, return
CAM_DEV_NOT_THERE so that CAM will not destroy attached disks under
the blkvsc controllers.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Discussed with: mav
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7693
Suspend:
- Prevent the backend from being touched on TX path.
- Clear the RNDIS RX filter, and wait for RX to drain.
- Make sure that NVS see the chimney sending buffer and RXBUF
disconnection, before unlink these buffers from the channel.
Resume:
- Reconfigure the RNDIS filter.
- Allow TX path to work on the backend.
- Kick start the TX eof task, in case the OACTIVE is set.
This fixes various panics, when the interface has traffic and MTU
is being changed.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8046
It's unsafe to update the BAR when the related EN bit is set.
Submitted by: Dexuan Cui <decui microsoft com>
Reviewed by: jhb
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7914
Elantech trackpads are found in some laptops like the Asus UX31E. They
are "synaptics compatible" but use a slightly different protocol.
Elantech hardware support is not enabled by default and just like
Synaptic or TrackPoint devices it should be enabled by setting
tunable, in this case hw.psm.elantech_support, to non-zero value
PR: 205690
Submitted by: Vladimir Kondratyev <wulf@cicgroup.ru>
MFC after: 1 week
Clear 'sc_calibrating' flag and stop calibration task when interface
is not associated; this fixes possible panic after detach.
Reported and tested by: hselasky
Reviewed by: adrian
MFC after: 6 days
'compat' can never be NULL, because the compatible check loop ends when
compat->ocd_str is NULL. This causes ds1307 to attach to any unclaimed i2c
device.
- Added bhnd(4) bus APIs for per-core ioctl/iost register access.
- Updated reset/suspend bhnd(4) APIs for compatibility with ioctl/iost
changes.
- Implemented core reset/suspend support for both bcma(4) and siba(4).
- Implemented explicit release of all outstanding PMU requests at the bus
level when putting a core into reset.
Approved by: adrian (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D8009
* Don't do the antenna switching when setting up the rate table - we don't
take into account whether it's an active antenna or not (eg shared with BT.)
I'll look into this a bit more later.
* The default antenna is still 1, I'll look into that a bit more later.
(So no, this doesn't fix it for Larry who needs ANT_B to be active, not
ANT_A.)
* My changes to the rate control setup used the wrong method for finding
a suitable rate, which led to 1M CCK frames being queued for 11a operation.
This is .. sub-optimal. Change the rate control lookup path to use
the global table instead of the per-node table, which won't be setup
until the node rate table is setup (which happens way too late in this
game.)
Tested:
* Intel 7260, 2G and 5G operation.
Add check for evdev argument of evdev_free being NULL. This is valid
value and should not cause crash. In this case evdev_free does nothing
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
AMD chipsets have proprietary mechanisms for dicovering resources.
Those resources are not discoverable via plug-and-play mechanisms
like PCI configuration registers or ACPI.
For this reason a chipset-specific knowledge of proprietary registers
is required.
At present there are two FreeBSD drivers that require the proprietary
resource discovery. One is amdsbwd which is a driver for the watchdog
timer in the AMD chipsets. The other is intpm SMBus driver when it
attaches to the newer AMD chipsets where the resources of the SMBus HBA
are not described in the regular PCI way.
In both cases the resources are discovered by accessing AMD PMIO space.
Thus, many definitions are shared between the two drivers.
This change puts those defintions into a common header file.
As an added benefit, intpm driver now supports newest FCHs built into
AMD processors of Family 15h, models 70h-7Fh and Family 16h, models
30h-3Fh.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8004
This changes the transmit rate control code to do a few things:
* use fixed rates (mcast, ucast, mgmt) where required.
* Don't use a hard-coded 11a or 11bg rate for non-data frames -
use what net80211 says we should use.
* use mgmtrate for EAPOL frames.
Reviewed by: avos
Differential Revision: https://reviews.freebsd.org/D7994
event generation is disabled by default in favour of sysmouse. This
behavoiur is controlled by kern.evdev.rcpt_mask sysctl, bit 2 should
be set to give priority to hw over sysmouse
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: hans
Differential Revision: https://reviews.freebsd.org/D7863
event generation is disabled by default in favour of kbdmux. This
behavoiur is controlled by kern.evdev.rcpt_mask sysctl, bit 3 should
be set to give priority to hw over mux
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: hans
Differential Revision: https://reviews.freebsd.org/D7957
During a bus rescan the check for an invalid vendor ID of a subfunction
used the wrong constant.
Submitted by: Dexuan Cui <decui@microsoft.com>
MFC after: 3 days
This is an RTL8168 chip, which we already support so all we have to do is add
the vendor ID.
PR: 212876
Submitted by: Tobias Kortkamp <t@tobik.me>
MFC after: 3 days
So that reinitialization, e.g. MTU change, will not fail when the system
memory is excessively fragmented.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7961
The assumption that the channel is only opened upon synthetic device
attach time no longer holds, e.g. Hyper-V network device MTU changes.
We have to allow device drivers to preallocate bufrings, e.g. in
attach DEVMETHOD, to prevent bufring allocation failure once the
system memory is fragmented after running for a while.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7960
Summary:
If the environment variable is set, U-boot adds a 'bootargs' property to
/chosen. This is already handled by ARM and MIPS, but should be handled in a
central location. For now, ofw_subr.c is a good place until we determine if it
should be moved to init_main.c, or somewhere more central to all architectures.
Eventually arm and mips should be modified to use ofw_parse_bootargs() as well,
rather than using the duplicate code already.
Reviewed By: adrian
Differential Revision: https://reviews.freebsd.org/D7846
So that NVS version probing failure does not look too scary.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7950
* We need to first call ivp->iv_newstate(), to enqueue the deauth/deassoc
mgmt frame, then flush the tx queue, before actually calling
iwm_release().
* cycling a wlan connection via wpa_cli frontend to wpa_supplicant, by
issuing disconnect and reconnect commandos works quite well.
(There is still an issue when disconnecting/reconnecting too quickly)
* Reassociating or roaming via wpa_supplicant is still broken.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7943
* No functional change, none of these values were ever read.
* The values removed from struct iwm_nvm_data are only used for old dvm
devices in Linux iwlwifi, and irrelevant to iwm hence.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7945
* This removes deprecated scan API definitions, which have been unused
since the upgrade to version 16 firmware in change r303327.
* Part of this change matches the header-file changes in Linux git commit
1f9403863c080478ad78247c89b018e95bdfb027.
* No functional change.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7937
The iwm(4) iwm_poll_bit() function returns 1 on success, and 0 on failure,
whereas the iwl_poll_bit() in Linux iwlwifi returns < 0 on failure.
So the (ret < 0) check ended up ignoring any error returned by
iwm_poll_bit().
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7932
This fixes a potential buffer overrun in the firmware parsing code.
Reported by: Coverity
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7931
The wantresp field in struct iwm_rx_data has never been used for anything,
so we can just delete it.
Apparently struct iwm_sf_cfg_cmd was compiled correctly (using a 32bit
value to represent the enum), but it still seems like a very bad idea to use
an enum type in a __packed struct.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7930
The htole32 was working fine for little-endian machines, but would have
been broken on big-endian.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7929
- Don't change RNDIS RSS configuration for RSS key sysctl, if the
interface is not capable of RSS yet.
- Don't change RSS indirect table (both cached one and RNDIS RSS
configuration), if the interface is not capable of RSS yet.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7924
And don't allow capability changes during reinitialization, which
breaks too much static configuration.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7922
NVS and NDIS version change would break too much assumption and static
configuration.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7919
drivers.
The BMIPS32/BMIPS3300 cores use a register layout distinct from the MIPS74K
core, and are only found on siba(4) devices.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7791
While I'm here, add comment along the attach DEVMETHOD.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7874
* hard code a noise floor of -96 for now. The noise floor update code returns
some "interesting" values that I can't map to anything useful right now.
* Ensure a default noise floor is set - otherwise the initial scan results
have a noise floor of '0'.
* Fix up the RSSI calculation to be correctly relative to the noise floor.
The RSSI routines return an absolute value in dBm - so fix this up.
* Cap RSSI values appropriately.
* Ensure we pass in a 1/2 dB unit value in to net80211.
Tested:
* Intel 7260, STA mode
iwm0: <Intel Dual Band Wireless AC 7260> mem 0xf1400000-0xf1401fff irq 17 at device 0.0 on pci2
iwm0: hw rev 0x140, fw ver 16.242414.0, address xx:xx:xx:xx:xx:xx
In r304870, refcount handling was lifted out into a common OTP/SPROM code
path, but the refcount assertions in chipc_disable_sprom_pins() were not
updated accordingly; this triggered an assertion on BCM4331 devices when
releasing a SPROM pin reservation.
Approved by: adrian (mentor, implicit)
Make virtio_console(4) create `/dev/vtcon/<port_name>` alias pointing
to /dev/ttyVx.y upon receiving PORT_NAME (id = 7) event over the control
queue.
Approved by: trasz
MFC after: 1 month
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D7182
When mlx5e_sq_xmit() returns an error code and the mbuf pointer is set,
we should not free the mbuf, because the caller will keep the mbuf in
the drbr. Make sure the mbuf pointer is correctly set upon function
exit.
Sponsored by: Mellanox Technologies
MFC after: 1 week
The hardware MTU size can't be set to a value less than 1500 bytes due
to side-band management support. Allow setting the software MTU size
below 1500 bytes, thus creating a mismatch between hardware and
software MTU sizes.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Try to reuse code to setup sendqueues when possible by making some static
functions global. Further split the mlx5e_close_sq_wait() function to
separate out reusable parts.
Sponsored by: Mellanox Technologies
MFC after: 1 week
This change also reduces the size of the mlx5e_sq structure so that the last
queue_state element will fit into the previous cacheline and then the mlx5e_sq
structure becomes one cacheline less for amd64.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Make some functions and structures global to allow for code reuse
when creating rate limiting sendqueues.
Sponsored by: Mellanox Technologies
MFC after: 1 week
Move setting of CQ moderation mode together with the other
CQ moderation parameters. Pass completion event vector as
a separate argument to mlx5e_open_cq(), because its value is
different for each call. Pass mlx5e_priv pointer instead of
mlx5e_channel pointer so that code can be used by rate
limiting sendqueues.
Sponsored by: Mellanox Technologies
MFC after: 1 week
This change allows for reusing the transmit path for so called
rate limited senqueues. While at it optimise some pointer lookups
in the fast path.
Sponsored by: Mellanox Technologies
MFC after: 1 week
- Add new firmware commands and update existing ones.
- Add more firmware related structures and update existing ones.
- Some minor fixes, like adding missing \n to some prints.
Sponsored by: Mellanox Technologies
MFC after: 1 week
come up as 't6nex' nexus devices with 'cc' ports hanging off them.
The T6 firmware and configuration files will be added as soon as they
are released. For now the driver will try to work with whatever
firmware and configuration is on the card's flash.
Sponsored by: Chelsio Communications
mutexes or using any callouts when active.
Trying to lock a mutex when KDB is active or the scheduler is stopped
can result in infinite wait loops. The same goes for calling callout
related functions which in turn lock mutexes.
If the USB controller at which a USB keyboard is connected is idle
when KDB is entered, polling the USB keyboard via USB will always
succeed. Else polling may fail depending on which state the USB
subsystem and USB interrupt handler is in. This is unavoidable unless
KDB can wait for USB interrupt threads to complete before stalling the
CPU(s).
Tested by: Bruce Evans <bde@freebsd.org>
MFC after: 4 weeks
- ifnet.if_mtu does not require explicit setting.
- ifnet.if_hdrlen must be set after ether_ifattach().
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7873
It is available on both stable/10 and stable/11. This eases future MFCs
to stable/10.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7872
This paves the way for the dynamic RSS key and indirect table setting.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7864
This paves the way for further attach/detach code reorganization.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7858
* Don't do RTS/CTS - experiments show that we get ACK frames for each of them
and this ends up causing the timestamps to look all funny.
* Set the HAL_TXDESC_POS bit, so the AR9300 HAL sets up the hardware to return
location and CSI information.
evdev is a generic input event interface compatible with Linux
evdev API at ioctl level. It allows using unmodified (apart from
header name) input evdev drivers in Xorg, Wayland, Qt.
This commit has only generic kernel API. evdev support for individual
hardware drivers like ukbd, ums, atkbd, etc. will be committed later.
Project was started by Jakub Klama as part of GSoC 2014. Jakub's
evdev implementation was later used as a base, updated and finished
by Vladimir Kondratiev.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: adrian, hans
Differential Revision: https://reviews.freebsd.org/D6998
Trying to build a MIPS platform that uses INTRNG needs this
for this to work right in gpiobusvar.h :
#ifdef INTRNG
struct intr_map_data_gpio {
struct intr_map_data hdr;
...
};
#endif
* change the HT_RC_2_MCS to do MCS0..23
* Use it when looking up the ht20/ht40 array for bits-per-symbol
* add a clk_to_psec (picoseconds) routine, so we can get sub-microsecond
accuracy for the math
* .. and make that + clk_to_usec public, so higher layer code that is
returning clocks (eg the ANI diag routines, some upcoming locationing
experiments) can be converted to microseconds.
Whilst here, add a comment in ar5416 so i or someone else can revisit the
latency values.
The GUID string provided by hypervisor has leading and trailing braces,
while our GUID string does not have braces at all. Both braces should
be ignored, when the GUID strings are compared.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Modified by: sephe
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7809
While I'm here, pull up the channel callback related code too.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7805
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
If a packet contains the Ethernet header (14 bytes) in the first mbuf
and the payload (IP + UDP + data) in the second mbuf, then the attempt
to fetch the l3hdr will return a NULL pointer. The first loop iteration
will drop len to zero and exit the loop without setting 'p'. However,
the desired data is at the start of the second mbuf, so the correct
behavior is to loop around and let the conditional set 'p' to m_data of
the next mbuf (and leave offset as 0).
Reviewed by: np
Sponsored by: Chelsio Communications
Due to reading initialized variable, FIS receive area was always allocated
as 256 bytes, suitable for command-based switching, instead of 4096 bytes,
required for FIS-based switching. This caused memory corruption in case of
port multipliers used on FBS-capable HBAs (Marvell).
MFC after: 1 week
Add routines to trigger a function level reset (FLR) of a PCI-express
device via the PCI-express device control register. This also includes
support routines to wait for pending transactions to complete as well
as calculating the maximum completion timeout permitted by a device.
Change the ppt(4) driver to reset pass through devices before attaching
to a VM during startup and before detaching from a VM during shutdown.
Reviewed by: imp, wblock (earlier version)
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7751
This driver supports two bindings:
- cpufreq-dt: systems which share clock and voltage across all CPUs
- arm_big_little_dt: systems which share clock and voltage across all
CPUs in a single cluster
Reviewed by: andrew, imp
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D7741
When the I/O MMU is active in bhyve, all PCI devices need valid entries
in the DMAR context tables. The I/O MMU code does a single enumeration
of the available PCI devices during initialization to add all existing
devices to a domain representing the host. The ppt(4) driver then moves
pass through devices in and out of domains for virtual machines as needed.
However, when new PCI devices were added at runtime either via SR-IOV or
HotPlug, the I/O MMU tables were not updated.
This change adds a new set of EVENTHANDLERS that are invoked when PCI
devices are added and deleted. The I/O MMU driver in bhyve installs
handlers for these events which it uses to add and remove devices to
the "host" domain.
Reviewed by: imp
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7667
Other files including pci_host_generic.h failed to compile
due to missing declaration of enum pci_id_type.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Reviewed by: wma
Differential Revision: https://reviews.freebsd.org/D7561
Split usbd_xfer_status() check:
- Check xfer length: must be longer, than Rx descriptor size.
- Check frame size: must be shorter than xfer length.
- Discard too short frames.
Tested with WUSB54GC, STA/MONITOR modes.
This adds bhnd(4) bus-level support for querying backplane interrupt vector
routing, and delegating machine/bridge-specific interrupt handling to the
concrete bhnd(4) driver implementation.
On bhndb(4) bridged PCI devices, we provide the PCI/MSI interrupt directly
to attached cores.
On MIPS devices, we report a backplane interrupt count of 0, effectively
disabling the bus-level interrupt assignment. This allows mips/broadcom
to temporarily continue using hard-coded MIPS IRQs until bhnd_mips PIC
support is implemented.
Reviewed by: mizhka
Approved by: adrian (mentor, implicit)
Broadcom Intensi-fi chipsets provided a common set of IP cores; on PCI/PCIe
devices, the USB11 host controller is left floating.
Approved by: adrian (mentor, implicit)
This patch adds driver implementation for BHND USB core. Driver has been
imported from ZRouter project with small adaptions for FreeBSD 11.
Also it's enabled for BroadCom MIPS74k boards by default. It's fully tested
on Asus boards (RT-N16: external USB, RT-N53: USB bus between SoC and WiFi
chips).
Reviewed by: adrian (mentor), ray
Approved by: adrian (mentor)
Obtained from: ZRouter
Differential Revision: https://reviews.freebsd.org/D7781
by reviving the SX control request lock and refining which lock
protects the common scratch area in "struct usb_device".
The SX control request lock was removed by r246759 because it caused a
lock order reversal with the USB enumeration lock inside
usbd_transfer_setup() as a function of r246616. It was thought that
reducing the number of locks would resolve the LOR, but because some
USB device drivers use usbd_do_request_flags() inside callback
functions, like in taskqueues, a deadlock may occur when these are
drained from device_detach(). By restoring the SX control request
lock usbd_do_request_flags() is allowed to complete its execution
when a USB device driver is detaching. By using the SX control request
lock to protect the scratch area, the LOR introduced by r246616 is
also resolved.
Bump the FreeBSD version while at it to force recompilation of all USB
kernel modules.
Found by: avos@
MFC after: 1 week
sys/dev/usb/serial/uplcom.c:543:29: error: implicit conversion from 'int' to 'int8_t' (aka 'signed char') changes value from 192 to -64 [-Werror,-Wconstant-conversion]
if (uplcom_pl2303_do(udev, UT_READ_VENDOR_DEVICE, UPLCOM_SET_REQUEST, 0x8484, 0, 1)
~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~
sys/dev/usb/usb.h:179:53: note: expanded from macro 'UT_READ_VENDOR_DEVICE'
#define UT_READ_VENDOR_DEVICE (UT_READ | UT_VENDOR | UT_DEVICE)
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~
This is because UT_READ is 0x80, so the int8_t argument is wrapped to a
negative value. Fix this by using uint8_t instead.
Reviewed by: imp, hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7776
This fixes bhnd(4) nvram handling on devices that map SPROM CSRs via PCI
configuration space.
The probe method previously required that a bhnd(4) device be attached to the
parent bridge; now that the bhnd_nvram device is always attached first, this
unnecessary sanity check always failed.
Approved by: adrian (mentor, implicit)
On BCM4321 chipsets, both PCI and PCIe cores are included, with one of
the cores potentially left floating.
Since the PCI core appears first in the device table, and the PCI
profiles appear first in the resource configuration tables, this resulted in
incorrectly matching and using the PCI/v1 resource configuration on PCIe
devices, rather than the correct PCIe/v1 profile.
Approved by: adrian (mentor, implicit)
Adds support for probing and initializing bhndb(4) bridge state using
the bhnd_erom API, ensuring that full bridge configuration is available
*prior* to actually attaching and enumerating the bhnd(4) child device,
allowing us to safely allocate bus-level agent/device resources during
bhnd(4) bus enumeration.
- Add a bhnd_erom_probe() method usable by bhndb(4). This is an analogue
to the existing bhnd_erom_probe_static() method, and allows the bhndb
bridge to discover the best available erom parser class prior to newbus
probing of its children.
- Add support for supplying identification hints when probing erom
devices. This is required on early EXTIF-only chipsets, where chip
identification registers are not available.
- Migrate bhndb over to the new bhnd_erom API, using bhnd_core_info
records rather than bridged bhnd(4) device_t references to determine
the bridged chipsets' capability/bridge configuration.
- The bhndb parent (e.g. if_bwn) is now required to supply a hardware
priority table to the bridge. The default table is currently sufficient
for our supported devices.
- Drop the two-pass attach approach we used for compatibility with bhndb(4) in
the bhnd(4) bus drivers, and instead perform bus enumeration immediately,
and allocate bridged per-child bus-level resources during that enumeration.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7768
This defines a new bhnd_erom_if API, providing a common interface to device
enumeration on siba(4) and bcma(4) devices, for use both in the bhndb bridge
and SoC early boot contexts, and migrates mips/broadcom over to the new API.
This also replaces the previous adhoc device enumeration support implemented
for mips/broadcom.
Migration of bhndb to the new API will be implemented in a follow-up commit.
- Defined new bhnd_erom_if interface for bhnd(4) device enumeration, along
with bcma(4) and siba(4)-specific implementations.
- Fixed a minor bug in bhndb that logged an error when we attempted to map the
full siba(4) bus space (18000000-17FFFFFF) in the siba EROM parser.
- Reverted use of the resource's start address as the ChipCommon enum_addr in
bhnd_read_chipid(). When called from bhndb, this address is found within the
host address space, resulting in an invalid bridged enum_addr.
- Added support for falling back on standard bus_activate_resource() in
bhnd_bus_generic_activate_resource(), enabling allocation of the bhnd_erom's
bhnd_resource directly from a nexus-attached bhnd(4) device.
- Removed BHND_BUS_GET_CORE_TABLE(); it has been replaced by the erom API.
- Added support for statically initializing bhnd_erom instances, for use prior
to malloc availability. The statically allocated buffer size is verified both
at runtime, and via a compile-time assertion (see BHND_EROM_STATIC_BYTES).
- bhnd_erom classes are registered within a module via a linker set, allowing
mips/broadcom to probe available EROM parser instances without creating a
strong reference to bcma/siba-specific symbols.
- Migrated mips/broadcom to bhnd_erom_if, replacing the previous MIPS-specific
device enumeration implementation.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7748
sys/dev/cxgb/cxgb_sge.c:2873:44: error: implicit conversion from 'int'
to 'char' changes value from 128 to -128 [-Werror,-Wconstant-conversion]
*mtod(m, char *) = CPL_ASYNC_NOTIF;
~ ^~~~~~~~~~~~~~~
This is because CPL_ASYNC_NOTIF is 0x80, so the plain char argument is
wrapped to a negative value. Fix this by using uint8_t instead.
Reviewed by: np
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7772
sys/dev/ppbus/ppb_1284.c:296:46: error: implicit conversion from 'int'
to 'char' changes value from 144 to -112 [-Werror,-Wconstant-conversion]
if ((error = do_peripheral_wait(bus, SELECT | nBUSY, 0))) {
~~~~~~~~~~~~~~~~~~ ~~~~~~~^~~~~~~
sys/dev/ppbus/ppb_1284.c:785:48: error: implicit conversion from 'int'
to 'char' changes value from 240 to -16 [-Werror,-Wconstant-conversion]
if (do_1284_wait(bus, nACK | SELECT | PERROR | nBUSY,
~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
sys/dev/ppbus/ppb_1284.c:786:29: error: implicit conversion from 'int'
to 'char' changes value from 240 to -16 [-Werror,-Wconstant-conversion]
nACK | SELECT | PERROR | nBUSY)) {
~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
This is because nBUSY is 0x80, so the plain char argument is wrapped to
a negative value. Fix this in a minimal fashion, by using uint8_t in a
few places.
Reviewed by: emaste
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7771
transfers.
The Initiator and Target both perform zero copy receive for transfers
greater than or equal to this threshold.
Sponsored by: Chelsio Communications
routines available in t4_tom to manage the iSCSI DDP page pod region.
This adds the ability to use multiple DDP page sizes to the iSCSI
driver, among other improvements.
Sponsored by: Chelsio Communications
important detail that sc_cngetc() now opens and closes the keyboard
on every call again. This was moved from sc_cngetc() to scn_cngrab/
ungrab() in r228644, but the change wasn't quite complete. After
fixes for nesting in kbdd_poll() in ukbd and kbdmux, these opens
and closes should have no significant effect if done while grabbed.
They fix unusual cases when cngetc() is called while not grabbed.
This commit is the main fix for screen locking in sc_cnputc():
detect deadlock or likely-deadlock and handle it by buffering the
output atomically and printing it later if the deadlock condition
clears (and sc_cnputc() is called).
The most common deadlock is when the screen lock is held by ourself.
Then it would be safe to acquire the lock recursively if the console
driver is calling printf() in a safe context, but we don't know when
that is. It is not safe to ignore the lock even in kdb or panic mode.
But ignore it in panic mode. The only other known case of deadlock
is when another thread holds the lock but is running on a stopped CPU.
Detect that case approximately by using trylock and retrying for 1000
usec. On a 4 GHz CPU, 100 usec is almost long enough -- screen switches
take slightly longer than that. Not retrying at all is good enough
except for stress tests, and planned future versions will extend the
timeout so that the stress tests work better.
To see the behaviour when deadlock is detected, single step through
sctty_outwakeup() (or sc_puts() to start with deadlock). Another
(serial) console is needed to the buffered-only output, but the
keyboard works in this context to continue or step out of the
deadlocked region. The buffer is not large enough to hold all the
output for this.
The purpose of BHND_PMU_{GET,SET}_BITS macro is to transform values from/into
register format. SET macro shifts value to left and applies filter mask.
GET macro applies filter mask and then shifts value to right.
Reviewed by: landonf, adrian (mentor)
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7721
The variables that are extern in the netmap header file should be
defined in ixl_txrx.c (the file that is included in both ixl(4)/ixlv(4),
not in the main driver source files.
Reported by: ed@, dim@, ngie@
Keyboard input needs Giant locking, and that is not possible to do
correctly here. Use mtx_trylock() and proceed unlocked as before if
we can't acquire Giant (non-recursively), except in kdb mode don't
even try to acquire Giant. Everything here is a hack, but it often
works. Even if mtx_trylock() succeeds, this might be a LOR.
Keyboard input also needs screen locking, to handle screen updates
and switches. Add this, using the same simplistic screen locking
as for sc_cnputc().
Giant must be acquired before the screen lock, and the screen lock
must be dropped when calling the keyboard driver (else it would get a
harmless LOR if it tries to acquire Giant). It was intended that sc
cn open/close hide the locking calls, and they do for i/o functions
functions except for this complication.
Non-console keyboard input is still only Giant-locked, with screen
locking in some called functions. This is correct for the keyboard
parts only.
When Giant cannot be acquired properly, atkbd and kbdmux tend to race
and work (they assume that the caller acquired Giant properly and don't
try to acquire it again or check that it has been acquired, and the
races rarely matter), while ukbd tends to deadlock or panic (since it
does the opposite, and has other usb threads to deadlock with).
The keyboard (Giant) locking here does very little, but the screen
locking completes screen locking for console mode except for not
detecting or handling deadlock.
- By default, adjust time upon SYNC request. It can be disabled
through hw.hvtimesync.ignore_sync_req. SYNC request will be
sent by hypervisor the host is resumed, rebooted, etc.
- By default, adjust time upon SAMPLE request, if there is 100ms
difference between VM time and hypervisor time. This can be
disabled through hw.hvtimesync.sample_drift.
And nuke the unnecessary task, since channel callback is running
in a Hyper-V taskqueue nowadays.
Submitted by: YanZhe Chen <t-yachen microsoft com>
Discussed with: Dexuan Cui <decui microsoft com>, Hongjiang Zhang <honzhan microsoft com>, sephe
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7707
Previously this reported an error from Clang 3.9.0: implict conversion
from 'int' to 'char' changes value from 128 to -128.
Discussed with: dim, trasz
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7699
this, and sc will soon depend on it again.
The on/off request is passed without modification to lower layers,
so the bug was smaller in this layer than in in lower layers (the
sequence on;on;off left polling off when it should be on, but the
sequence on;on;off;on;off... doesn't allow the interrupt handler
to eat the input after an "off" that should't turn off polled mode,
provided lower layers don't have the bug, since this layer is virtual.
The bug was small in lower layers too. Normally everything is Giant
locked for keyboards, and this locks out the interrupt handler in
on;on;off;on;off... sequences. However, PR 211884 says that fixing
this bug in ukbd in r303765 apparently causes the eating-by-interrupt
behaviour that the fix is to prevent.
Discussed with: emax
Restore an splx() lost in r228644. We aren't nearly ready to remove
spl's. They give hints about missing locking. This lost one was
misplaced. Dropping it early for convenience gave race windows for
accesses to the fkey buffer. Giant locking accidentally fixed this
for non-console cases.
Put the spl's around the whole function. Since there are many returns
that would need splx() just before them for a direct fix, split the
function into a wrapper that does the spl's and a "locked" function
that does the work.
Return earlier when no keyboard is attached to match the ordering in a
planned version. This breaks the dubious feature of returning keys
from the fkey buffer after the keyboard has gone away. Losing the keys
wouldn't matter, but we keep them too long now.
Actually all OIDs defined in net/rndis.h are standard NDIS OIDs.
While I'm here, use the verbose macro name as in NDIS spec.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7679
Adding the compatible property check isn't enough. Device trees for eTSEC2
devices are missing a 'reg' property on the eTSEC node itself, relegating it to
the queue group child nodes.
Still left to do: add Multigroup mode support (see QorIQ reference manuals s for
SoCs with eTSEC2).
MFC after: 2 weeks
Relnotes: Yes
The device quiet flag is not automatically reset on detach, so it is
inherited by other device drivers (e.g. when switching a device driver
over to ppt for PCI pass through). Cope with this behavior by explicitly
marking the device verbose during detach so that the next driver can make
its own decision.
Sponsored by: Chelsio Communications
In r304602, I mistakenly removed the ioat_process_events check that we weren't
processing events before the hardware had completed the descriptor
("last_seen"). Reinstate that logic.
Keep the defensive loop condition and additionally make sure we've actually
completed a descriptor before blindly chasing the ring around.
In reset, queue and finish the startup command before allowing any event
processing or submission to occur. Avoid potential missed callouts by
requeueing the poll later.
just use the same mutex locking as sc cn putc so they have the same
defects.
The locking calls to acquire the lock are actually in sc cn open and close.
Ungrab has to unlock, although this opens a race window.
Change the direct mutex lock calls in sc cn putc to the new locking
functions via the open and close functions. Putc also has to unlock, but
doesn't keep the screen open like grab. Screen open and close reduce to
locking, except screen open for grab also attempts to switch the screen.
Keyboard locking is more difficult and still null, even when keyboard
input calls screen functions, except some of the functions have locks
too deep to work right.
This organization gives a single place to fix some of the locking.
This fixes a tautological pointer comparison warning, but would also a
real bug for a platform where bus_dmamap_unload of a static allocation
is not a no-op.
Summary:
Some device trees put "fsl,ns16650" first in the compatible list. This causes
the probe code to choke, even though the device is compatible with ns16650, and
has it listed later in the tree.
Reviewed by: nwhitehorn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7676
This will allow us to perform bhndb(4) bridge configuration based on
the identified hardware, prior to performing full enumeration of the
child bhnd bus.
Approved by: adrian (mentor, implicit)
handling.
- Extended PWRCTL/PMU APIs to support querying clock frequency during very
early boot, prior to bus attach.
- Implement generic PMU-based calculation of UART rclk values.
- Replaced use of static frequency tables (bcm_socinfo) with
runtime-determined values.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7552
- Added bhnd_pmu driver implementations for PMU and PWRCTL chipsets,
derived from Broadcom's ISC-licensed HND code.
- Added bhnd bus-level support for routing per-core clock and resource
power requests to the PMU device.
- Lift ChipCommon support out into the bhnd module, dropping
bhnd_chipc.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7492
This adds support for performing platform_reset() on all supported
devices, using early boot enumeration of chipc capabilities and
available cores.
- Added Broadcom-specific MIPS CP0 register definitions used by
BCM4785-specific reset handling.
- Added a bcm_platform structure for tracking chipc/pmu/cfe platform
data.
- Extended the BCMA EROM API to support early boot lookup of core info
(including port/region mappings).
- Extended platform_reset() to support PMU, PMU+AOB, and non-PMU
devices.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7539
- Return appropriate error code instead of ENOMEM when sosend() fails in
send_mpa_req.
- Fix for problematic race during destroy_qp.
- Abortive close in the failure of send_mpa_reject() instead of normal close.
- Remove the unnecessary doorbell flowcontrol logic.
Submitted by: Krishnamraju Eraparaju at Chelsio
MFC after: 1 month
Sponsored by: Chelsio communications
And use new RNDIS set to configure NDIS offloading parameters.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7641
And switch MAC address query to use new RNDIS query function.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7639
hardware send and receive PDU limits. Report these limits to ICL and
take them into account when setting the socket's send and receive buffer
sizes. The driver used a single hardcoded limit everywhere prior to
this change.
Sponsored by: Chelsio Communications
syscons spinlock for the output routine alone. It is better to extend
the coverage of the first syscons spinlock added in r162285. 2 locks
might work with complicated juggling, but no juggling was done. What
the 2 locks actually did was to cover some of the missing locking in
each other and deadlock less often against each other than a single
lock with larger coverage would against itself. Races are preferable
to deadlocks here, but 2 locks are still worse since they are harder
to understand and fix.
Prefer deadlocks to races and merge the second lock into the first one.
Extend the scope of the spinlocking to all of sc_cnputc() instead of
just the sc_puts() part. This further prefers deadlocks to races.
Extend the kdb_active hack from sc_puts() internals for the second lock
to all spinlocking. This reduces deadlocks much more than the other
changes increases them. The s/p,10* test in ddb gets much further now.
Hide this detail in the SC_VIDEO_LOCK() macro. Add namespace pollution
in 1 nested #include and reduce namespace pollution in other nested
#includes to pay for this.
Move the first lock higher in the witness order. The second lock was
unnaturally low and the first lock was unnaturally high. The second
lock had to be above "sleepq chain" and/or "callout" to avoid spurious
LORs for visual bells in sc_puts(). Other console driver locks are
already even higher (but not adjacent like they should be) except when
they are missing from the table. Audio bells also benefit from the
syscons lock being high so that audio mutexes have chance of being
lower. Otherwise, console drviver locks should be as low as possible.
Non-spurious LORs now occur if the bell code calls printf() or is
interrupted (perhaps by an NMI) and the interrupt handler calls
printf(). Previous commits turned off many bells in console i/o but
missed ones done by the teken layer.
- Increasing queue depth gives ~100% performance improvement for
randwrite fio test in Azure.
- New channel selection, which takes LUN id and the current cpuid
into consideration, gives additional ~20% performance improvement
for ranwrite fio test in Azure.
Submitted by: Hongzhang Jiang <honzhan microsoft com>
Modified by: sephe
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7622
Decouple the send and receive limits on the amount of data in a single
iSCSI PDU. MaxRecvDataSegmentLength is declarative, not negotiated, and
is direction-specific so there is no reason for both ends to limit
themselves to the same min(initiator, target) value in both directions.
Allow iSCSI drivers to report their send, receive, first burst, and max
burst limits explicitly instead of using hardcoded values or trying to
derive all of them from the receive limit (which was the only limit
reported by the drivers prior to this change).
Display the send and receive limits separately in the userspace iSCSI
utilities.
Reviewed by: jpaetzel@ (earlier version), trasz@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7279
indicate (potentially partial) success of the open. Use these to
decide what to close in sccnclose(). Only grab/ungrab use open/close
so far.
Add a per-sc variable to count successful keyboard opens and use
this instead of the grab count to decide if the keyboad state has
been switched.
Start fixing the locking by using atomic ops for the most important
counter -- the grab level one. Other racy counting will eventually
be fixed by normal mutex or kdb locking in most cases.
Use a 2-entry per-sc stack of states for grabbing. 2 is just enough
to debug grabbing, e.g., for gets(). gets() grabs once and might not
be able to do a full (or any) state switch. ddb grabs again and has
a better chance of doing a full state switch and needs a place to
stack the previous state. For more than 3 levels, grabbing just
changes the count. Console drivers should try to switch on every i/o
in case lower levels of nesting failed to switch but the current level
succeeds, but then the switch (back) must be completed on every i/o
and this flaps the state unless the switch is null. The main point
of grabbing is to make it null quite often. Syscons grabbing also
does a carefully chosen screen focus that is not done on every i/o.
Add a large comment about grabbing.
Restore some small lost comments.
- in sccnopen(), open the keyboard before the screen. The keyboard
currently requires Giant (although it must be spinlocked to work
correctly as a console), so the previous order would be a LOR if
it has any semblance of locking.
- add a (currently dummy) state arg to scgetc().
Use sbintime_t timeouts with precision control to get very accurate
timing. It costs little to always ask for about 1% accuracy, and the
not so new event timer implementation usual delivers that, and when
it can't it gets much closer than our previous coarse timeouts and
buggy simple countdown.
The 2 fastest atkbd repeat rates have periods 34 and 38 msec, and ukbd
pretended to support rates in between these. This requires
sub-microsecond precision and accuracy even to handle the 4 msec
difference very well, but ukbd asked the timeout subsystem for timeouts
of 25 msec and the buggy simple countdown of this gave a a wide range
of precisions and accuracies depending on HZ and other timer
configuration (sometimes better than 25 msec but usually more like 50
msec). We now ask for and usually get precision and accuracy of about
1% for each repeat and much better on average.
The 1% accuracy is overkill. Rounding of 30 cps to 34 msec instead of
33 already gives an error of +2% instead of -1%, and ut AT keyboards on
PS/2 interfaces have similar errors.
A timeout is now scheduled for every keypress and release. This allows
some simplifications that are not done. It allows removing the timeout
scheduling for exiting polled mode where it was unsafe in ddb mode. This
is done. Exiting polled mode had some problems with extra repeats. Now
exiting polled mode lets an extra timeout fire and the state is fudged
so that the timeout handler does very little.
The sc->time_ms variable is unsigned to avoid overflow. Differences of
it need to be signed. Signed comparisons were emulated by testing an
emulated sign bits. This only works easily for '<' comparisonss, but
we now need a '<=' comparison. Change the difference variable to
signed and use a signed comparison. Using unsigned types here didn't
prevent overflow bugs but just reduced them. Overflow occurs with
n repeats at the silly repeat period of [U]INT_MAX / n. The old countdown
had an off by 1 error, and the simplifications would simply count down
1 to 0 and not need to accumulate possibly-large repeat repeats.
And stringent input IC version negotiate message checks.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7614
RESET is not used by the hn(4) at all, and RESET_CMPLT does not even
have a rid to match with the pending requests. So, let's put it
onto an independent switch branch and log a warning about it.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7602
kbdcontrol -r fast is documented to give a non-emulated atkbd's fastest
rate of 250.34, but is misimplemented to request this as 0.0. ukbd
supports many nonstandard rates, although it is currently too inaccurate
by a factor of several hundred for non-huge nonstandard rates to be
useful. It mapped 0.0 to 200.0. A repeat delay of 0 means a rate of
infinity which is quite fast, but physical constraints limit this to
a few MHz and the inaccuracies made it almost usable.
Convert 0.0 to the documented 250.34.
Also convert negative args and small args to the 250.34 minimal ones,
like atkbd does. This is for KDSETREPEAT -- the 2 versions of the
deprecated KDSETRAD have bounds checking. Keep not doing any bounds
checking or conversions for upper limits since nonstandard large
delays are useful for testing.
The inaccuracies are dependent on HZ and the timeout implementation.
With the old timeout implementation and HZ = 1000, 200.0 probably
worked better to emulate 250.34 than 250.34 itself. HZ = 100 gives
roundoff errors that accidentally reduce the inaaccuracies, and
event timers reduce the inaccuracies even more, so 200.0 was giving
more like itself (perhaps 215.15 on average but sometimes close to
10 msec repeat which is noticebly too fast). This commit makes 0.0
noticeably too slow, like 250.34 always was.
handling. This resulted in the window target being left uninitialized
when an underflow occured.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7617
This code should be able to support later AMD chipsets as well, but that
hasn't been tested.
SB800 supports accessing several different SMBus buses using the same
set of constrol registeirs plus special PMIO registers that control which
bus is selected. This could be exposed to consumers as several smb devices
each talking to its bus. This feature is not implemented yet.
MFC after: 2 weeks
So that Hyper-V can leverage them instead of rolling its own definition.
Discussed with: hps
Reviewed by: hps
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7592
its own job because this breaks the simplified QEMU XHCI TRB parser,
which expects the complete USB control transfer as a series of back to
back TRBs. The old behaviour is kept under #ifdef in case this change
breaks enumeration of any USB devices.
PR: 212021
MFC after: 1 week
The previous fix was tested mainly on 3 AT keyboards with USB adaptors where
it works. 1 USB keyboard doesn't translate Alt-PrintScreen, so the software
has to do it.
Reorganize a little to share some code and to not translate the unusual usb
scan code0x8a unless an Alt modified is set. Remove redundant check of Alt
modifiers. Translation now more clearly filters out Alt-PrintScreen before
the check.
The table of errors fixed in the previous commit had many bugs. Correct
table:
K_RAW Ctl-PrintScreen: E0-2A-E0-37 -> E0-37
K_RAW Alt-PrintScreen (with 4 comb. of Ctl/Shift): 79 -> 54
K_RAW Pause/Break (with 4 comb. of Alt/Shift): E0-46 -> E1-1D-45
K_CODE PrintScreen (with 4 comb. of Ctl/Shift): 54 -> 5c
K_CODE Alt-PrintScreen (with 4 comb. of Ctl/Shift): 7e -> 54
K_CODE Pause/Break (with 8 comb. of Ctl/Alt/Shift): 6c -> 68
That is 25 of 32 shift combinations for 2 keys fixed. All 16 combinations
were broken for K_CODE and thus also for K_XLATE.
is_completion_pending governs whether or not a callout will be scheduled
when new work is queued on the IOAT device. If true, a callout is
already scheduled, so we do not need a new one. If false, we schedule
one and set it true. Because resetting the hardware completed all
outstanding work but failed to clear is_completion_pending, no new
callout could be scheduled after a reset with pending work.
This resulted in a driver hang for polled-only work.
configuring of EP0 and non-EP0 into xhci_cmd_evaluate_ctx() and
xhci_cmd_configure_ep() respectivly. This resolves some errors when
using XHCI under QEMU and gets is more in line with the XHCI
specification.
PR: 212021
MFC after: 1 week
And don't recreate chimney sending buffer for each primary channel
open, it is now created in device_attach DEVMETHOD and destroyed
in device_detach DEVMETHOD.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7574
It seems Killer E2200/E2400 has a BIOS misconfiguration or silicon
bug which triggers DMA write errors when driver uses advertised
maximum payload size. Force the maximum payload size to 128 bytes
in DMA configuration.
This change should fix occasional DMA write errors reported on
Killer E2200.
Tested by: <psy0nic@sys-tek.org>
controllers. For Gigabit Ethernet version of AR816x, AR813x/AR815x
except L1D controller, use vendor recommended ASPM parameters.
While here, increase alc_dma_burst array size. Broken H/W can
return bogus value in theory.
so they are memory independent which allows for handling panics
triggered by the keyboard driver itself, typically via CTRL+ALT+ESC
sequences. Or if the USB keyboard driver was processing a key at the
moment of panic. Allow UKBD to be attached while keyboard polling is active.
Tested by: Bruce Evans <bde@freebsd.org>
MFC after: 1 week
everything was broken. The cases that I noticed were Ctrl-PrintScreen
not being mapped to the virtual scancode 0x5c (debug) and Pause not being
mapped to the physical/virtual scancode 0x46 (slock).
These keys are the most complicated ones due to kludges to give some
compatibility back to before AT keyboards.
Alt-PrintScreen must pretend to be a separate key from PrintScreen
even at the "raw" level. The (unique) usb code for it is 0x8a and we
just have to map this to our unique virtual scancode 0x54, but we
mapped it first to the internal code 0x7e and then to 0x79 which is a
key on the Japanese 106/109 keyboard. This fix is under the
UKBD_EMULATE_ATASCANCODE option which shouldn't be used for non-AT
keyboards. If it is, then the syscons Japanese keymaps have nothing
of importance for code 0x79 and can easily be changed. 0x54 is also
unimportant in Japanese and US keymaps.
NonAlt-PrintScreen and NonCtl-Pause/Break had many much larger bugs with
smaller compatibility problems from fixing them. The details are too
ugly to give here. Summary of the changed (hex) codes:
K_RAW PrintScreen (Ctl, Shift, Ctl-Shift): E0-2A-E0-37 -> E0-37
K_RAW Alt-PrintScreen (all shift states): 79 -> 54
K_RAW Pause/Break (unshifted, Shift, Alt, Alt-Shift)): E0-46 -> E1-1D-45
K_CODE ALT-PrintScreen (all shift states): 79 -> 54
That is 15 of 32 shift combinations for 2 keys fixed, with 8 easy cases
from the 79 -> 54 remapping.
The difference is only large and with no workaround using a keymap for
for K_RAW, but this affects other modes when ukbd is layered under kbmux
because kbmux keeps all subdevices in K_RAW mode and translates. Oops.
I used kbdmux to generate the above table of changes.
This driver only supports 10Mb Ethernet using PIO (the hardware supports
DMA, but the driver only does PIO). There are not any PCCard adapters
supported by this driver, only ISA cards. In addition, it does not use
bus_space but instead uses bcopy with volatile pointers triggering a
host of warnings. (if_ie.c is one of 3 files always built with
-Wno-error)
Relnotes: yes
The wl(4) driver supports pre-802.11 PCCard wireless adapters that
are slower than 802.11b. They do not work with any of the 802.11
framework and the driver hasn't been reported to actually work in a
long time.
Relnotes: yes
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
This permits a single early return for VF devices in the routines that
add sysctl nodes.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7512
Specifically, the FW_PORT_CMD may or may not work for a VF (the PF
driver can choose whether or not to permit access to this command),
so don't attempt to fetch port information on a VF if permission is
denied by the PF.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7511
While here, mark which parameters are PF-specific and which are
VF-specific.
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7508
- Read interrupt properties at bus enumeration time and store
it into global mapping table.
- At bus_activate_resource() time, given mapping entry is resolved and
connected to real interrupt source. A copy of mapping entry is attached
to given resource.
- At bus_setup_intr() time, mapping entry stored in resource is used
for delivery of requested interrupt configuration.
- For MSI/MSIX interrupts, mapping entry is created within
pci_alloc_msi()/pci_alloc_msix() call.
- For legacy PCI interrupts, mapping entry must be created within
pcib_route_interrupt() by pcib driver itself.
Reviewed by: nwhitehorn, andrew
Differential Revision: https://reviews.freebsd.org/D7493
And don't recreate RXBUF for each primary channel open, it is now
created in device_attach DEVMETHOD and destroyed in device_detach
DEVMETHOD.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7556
On the first switch we previously released the newly allocated keyboard
instead of the old one. Keyboard state was very confused afterwards for
further keyboard switches.
Submitted by: bde
axge_setmulti()/axge_setpromisc() with axge_rxfilter().
Multicast filter programming and promiscuous mode requires
access to a common RX configuration register so there is no need to
use separate functions with added complexity. axge_rxfilter() does
not read back AXGE_RCR register since accessing a register in USB
is too slow and we already have all knowledge of required
configuration. Rebuilding RX filter configuration is simpler and
faster than manipulating every bits after reading back the
register.
Note, axge_rxfilter() does not set RCR_IPE(IP header alignment on
32bit boundary) to disable extra padding bytes insertion. The
extra padding wastes ethernet to USB host bandwidth as well as
complicating RX handling logic. Current USB framework requires
copying RX frames to mbufs so there is no need to worry about
alignment. Previously axge_rx_frame() performed wrong bound check
due to the extra padding and it was broken when RX checksum
offloading is disabled. See added comment in axge_rx_frame () for
actual RX packet layout.
In axge_init(), disable WOL. It's meaningless to enable WOL in
normal operation.
In axge_rxeof(), use properly sized mbuf rather than blindly
allocating a mbuf cluster.
Use RX H/W checksum offloading only when administrator requested RX
checksum offloading. Previously it always used RX H/W checksum
offloading result regardless of RX checksum offloading state.
Separate L4 checksum offloading validation from L3 one and properly
set required offloading bits for each layer. This is to fix setting
L4 checksum offloading bits for L3 packets.
There are still lots of RX errors(probably RX FIFO overflows) under
moderate load. Users are strongly recommended to enable ethernet
flow control.
Reviewed by: kevlo (initial version), hselasky
This paves to nuke netvsc_packet, which does not serves much
purpose now.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7541
structures. This simplifies mbuf copy operation to USB buffers as
well as improving readability. The controller supports Microsoft
LSOv1(aka TSO) but this change set does not include the support due
to copying overhead to USB buffers and large amount of memory waste.
Remove useless ZLP padding which seems to come from Linux. Required
bits the code tried to set was not copied into USB buffer so it had
no effect. Unlike Linux, FreeBSD USB stack automatically generates
ZLP so no explicit padding is required in driver.[1]
Micro-optimize updating IFCOUNTER_OPACKETS counter by moving it out
of TX loop since updating counter is not cheap operation as it did
long time ago and we already know how many number of packets were
queued after exiting the loop.
While here, fix a checksum offloading bug which will happen when
upper stack computes checksum while H/W checksum offloading is
active. The controller should be notified to not recompute the
checksum in this case.
Reviewed by: kevlo (initial version), hselasky
Pointed out by: hselasky [1]
