PL (programmable logic) uses FCLK0..FCLK3 as a clock sources.
Normally they're configured by first stage boot loader (FSBL)
and normal user never has to touch them. These sysctls may come
useful for hardware developers
hw.fpga.fclk.N.source: clock source (IO, DDR, ARM)
hw.fpga.fclk.N.freq: requested frequency in Hz
hw.fpga.fclk.N.actual_freq: actual frequency in Hz (R/O)
hw.fgpa.level_shifters: 0/1 to enable/disable PS-PL level shifters,
normally they're enabled either by FSBL or after programming
FPGA through devcfg(4)
- Add no_dad and ignoreloop per-IF knob. no_dad disables DAD completely,
and ignoreloop is to prevent infinite loop in loopback probing state when
loopback is permanently expected.
emulate the instructions used in function entry and exit.
For function entry ARM will use a push instruction to push up to 16
registers to the stack. While we don't expect all 16 to be used we need to
handle any combination the compiler may generate, even if it doesn't make
sense (e.g. pushing the program counter).
On function return we will either have a pop or branch instruction. The
former is similar to the push instruction, but with care to make sure we
update the stack pointer and program counter correctly in the cases they
are either in the list of registers or not. For branch we need to take the
24-bit offset, sign-extend it, and add that number of 4-byte words to the
program counter. Care needs to be taken as, due to historical reasons, the
address the branch is relative to is not the current instruction, but 8
bytes later.
This allows us to use the following probes on ARM boards:
dtrace -n 'fbt::malloc:entry { stack() }'
and
dtrace -n 'fbt:🆓return { stack() }'
Differential Revision: https://reviews.freebsd.org/D2007
Reviewed by: gnn, rpaulo
Sponsored by: ABT Systems Ltd
rework the code a little bit to use this function consistently to cleanup
all the changes made as part of the probe phase.
This fixes an issue where a FDT child node without a matching driver could
leave the GPIO pins mapped and prevent the further use of them.
This prints a warning when your system have a hinted child or a FDT child
node for which you don't have a matching driver:
gpiobus0: <unknown device> at pin(s) 24 irq 24
have the same meaning and occupy the same memory address in the trapframe
courtesy of union. Avoid some pointless #ifdef by spelling them both 'DAR'
in the trapframe.
-mno-align-long-strings when compiling with base gcc. This is checked
by comparing the version number against 4.2.1, which is not exactly
right, but good enough. (There is no other way to check whether we are
using the non-standard gcc in base, as far as I know.)
Reported by: rodrigc
MFC after: 3 days
When several threads are trying to send datagram to the same destination,
but fragmentation is disabled and datagram size exceeds link MTU,
ip6_output() calls pfctlinput2(PRC_MSGSIZE). It does notify all
sockets wanted to know MTU to this destination. And since all threads
hold PCB lock while sending, taking the lock for each PCB in the
in6_pcbnotify() leads to deadlock.
RFC 3542 p.11.3 suggests notify all application wanted to receive
IPV6_PATHMTU ancillary data for each ICMPv6 packet too big message.
But it doesn't require this, when we don't receive ICMPv6 message.
Change ip6_notify_pmtu() function to be able use it directly from
ip6_output() to notify only one socket, and to notify all sockets
when ICMPv6 packet too big message received.
PR: 197059
Differential Revision: https://reviews.freebsd.org/D1949
Reviewed by: no objection from #network
Obtained from: Yandex LLC
MFC after: 1 week
Sponsored by: Yandex LLC
> List of fixes:
* use correct format for GID printouts
* double array indexing
* spelling in printouts
* void pointer arithmetic
* allow more receive rings
* correct maximum number of transmit rings
* use "const" instead of "static" for constants
* check for invalid VLAN tags
* check for lack of IRQ resources
> Added more hardware specific defines
> Added more verbose printouts of firmware status codes
Sponsored by: Mellanox Technologies
MFC after: 3 days
* Force the arge0 interface to not use a PHY for speed negotiation
for now. It'd be nice to do it, but right now the RGMII interface
to the switch needs to stay at 1000/full in order to match what
the switch side of the port is programmed as.
So until that's all sorted out, disconnect arge0 from the PHY
and leave it at fixed at 1000/full.
I noticed this when I tried using a busted ethernet cable that
forced the PHY to negotiate 100/full. The switch was fine and
it negotiated to 100/full, but then arge0 saw the link update
and set the speed to 100/full when the switch side of that
hook up was set to 1000/full. Tsk.
* When using argemdio, the mdio device resets and initialises
the MAC, /not/ the arge_attach (or, as I discovered, arge_init.)
So arge1 wasn't being fully initialised and thus no traffic
would ever flow.
So until I tidy up that mess, just create an argemdio bus for
arge1. It's totally fine; it won't do anything or find anything
attached to it.
Tested:
* AP135 reference board - both arge0 and arge1 now work.
to initialize mbuf's fibnum. Uninitialized fibnum value can lead to
panic in the routing code. Currently we use only RT_DEFAULT_FIB value
for initialization.
Differential Revision: https://reviews.freebsd.org/D1998
Reviewed by: hrs (previous version)
Sponsored by: Yandex LLC
is the case, depending on the options, in some of the ARM hardware
simulators. In these cases we don't get an interrupt so will need to
schedule the task to write more data to the uart.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
This new function can be used by other drivers to reserve the use of GPIO
pins.
Anyway, the use of ofw_gpiobus_parse_gpios() is preferred when possible.
Requested by: Michal Meloun
- fix warning about comparison of 'uint8_t v_tpr >= 0' always being true.
- fix error triggered by an empty clobber list in the inline assembly for
"clgi" and "stgi"
- fix error when compiling "vmload %rax", "vmrun %rax" and "vmsave %rax". The
gcc assembler does not like the explicit operand "%rax" while the clang
assembler requires specifying the operand "%rax". Fix this by encoding the
instructions using the ".byte" directive.
Reported by: julian
MFC after: 1 week
number of other subsystems, so you probably don't want _SPARE2..
ktr needs an overhaul to really only compile in the ones you want,
we've long passed the 31 bits it provides..
Sponsored by: transip.nl
if_vmove().
In if_vmove(), if_detach_internal() and if_attach_internal() were
called in series to detach and reattach the interface. When
detaching, if_delgroup() was called and the interface leaves all of
the group membership. And then upon attachment, if_addgroup(ifp,
IFG_ALL) was called and it joined only "all" group again.
This had a problem. Normally, a cloned interface automatically joins
a group whose name is ifc_name of the cloner in addition to "all"
upon creation. However, if_vmove() removed the membership and did
not restore upon attachment.
Differential Revision: https://reviews.freebsd.org/D1859
SCSI-2 devices.
Some older tape devices claim to be SCSI-2, but actually do support
long position information. (Long position information includes
the current file mark.) For example, the COMPAQ SuperDLT1.
So we now only disable the check on SCSI-1 and older devices.
sys/cam/scsi/scsi_sa.c:
In saregister(), only disable fetching long position
information on SCSI-1 and older drives. Update the
comment to explain why.
Confirmed by: dvl
Sponsored by: Spectra Logic
MFC after: 3 weeks
draft-ietf-6man-enhanced-dad-13.
This basically adds a random nonce option (RFC 3971) to NS messages
for DAD probe to detect a looped back packet. This looped back packet
prevented DAD on some pseudo-interfaces which aggregates multiple L2 links
such as lagg(4).
The length of the nonce is set to 6 bytes. This algorithm can be disabled by
setting net.inet6.ip6.dad_enhanced sysctl to 0 in a per-vnet basis.
Reported by: hiren
Reviewed by: ae
Differential Revision: https://reviews.freebsd.org/D1835
This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3
NIC and an AR8327 gigabit ethernet switch.
TODO:
* The AR8327 gigabit switch support bugfixes are forthcoming.
* 11ac support and 11ac NIC support
