o Consistently use device_foo_t and bus_foo_t for functions implementing
device_foo and bus_foo respectively. Adjust those routines that were wrong
(we should do this throughout the tree).
o make all the modules depend on usb. Otherwise these modules won't
load.
o ucycom doesn't need usb_port.h
o Minor unifdefing
o uhub, umass, ums, urio, uscanner conversion complete.
o ukbd: Remove the NO_SET_PROTO quirk (fixes a PR 77940). NetBSD removed
their check and setting the proto a long time ago.
o umodem panic fixed. UQ_ASSUME_CM_OVER_DATA quirk removed because I've never
seen a umodem that needed this rejection for proection (this gets rid of
~20% of the quirks).
Approved by: re@ (kensmith)
PR: 77940
Older drivers that do not wish to convert to the native API (which
will work with both 6.x and 7.x) can simply include
<dev/usb/usb_port.h>. Drivers in the tree shouldn't these macros,
unless they actually work on other OSes and are actively maintained.
Approved by: re@
Remove device_t dv, since it is no longer needed.
Add sizeof(device_t) to replace sizeof dv.
Change device_detach(dev) to device_detach(dev->subdevs[i]) since the type
of dev isn't right! Not sure when this was introduced, but it likely would
lead to a crash on disconnect.
MFC After: 1 week
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
Also, remove usb_malloc_type: it was unused.
Remove METHODS_NONE: it was unused.
Move include of opt_usb.h from usb_port.h to usb.h, since usb_port.h is
going away (there will be a usb_compat.h for out-of-tree drivers that want it).
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
error doing so. It seems an increasing number of phones have this
quirk, and we're not keeping up. There appears to be nothing bad that
happens for non-quirked phones.
Minor cleanups:
o prefer device_printf over printf
o kill devinfo stuff
o minor other preening.
need to do it at all anymore. Remove it from here. Expand
USB_ATTACH_SETUP inline now that it is one line and we're moving away
from the compat macros. Remove some bzero calls that turn out not be
be necessary.
what we print, don't print it anymore. And don't compute it anymore.
And don't malloc/free memory for it anymore. While I'm here, prefer
device_printf where appropriate.
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
OpenBSD's if_ral.c.
I didn't make the LINKSYS4 -> CISCOLINKSYS name change, nor did I
include the RALINK RT2573 that's supported by the rum(4) driver. I
didn't merge any code changes either.
supports software encrypt/decrypt.
The nuked code itself is quite problematic, as pointed out by sam@ ---
wk->wk_keyix should be replaced by the loop count.
Tested with WEP/TKIP/CCMP/no-protection.
Approved by: sam@ (mentor)
Noticed by: Hans Petter Selasky <hselasky@c2i.net>
- For ural(4):
o Fix node leakage in ural_start(), if ural_tx_mgt() fails.
o Fix mbuf leakage in ural_tx_{mgt,data}(), if usbd_transfer() fails.
o In ural_tx_{mgt,data}(), set ural_tx_data.{m,ni} to NULL, if
usbd_transfer() fails, so they will not be freed again in ural_stop().
Approved by: sam (mentor)
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
to a READ_CAPACITY request rather than the maximum sector (off by one
problem). This causes a huge cascade of errors as the geom tasting
code tries to read the last sector (which isn't really there in the
face of this error). automated tools that manipulate disk labels and
such also have issues.
Create a new quirk READ_CAPACITY_OFFBY1 and add a quirk for the
SanDISK ImageMate that I have that suffers from this problem (the
SDDR-31). It intercepts the READ_CAPACITY response and adjusts it
from number of sectors to max sector for devices with this quirk.
Reading the Linux source suggests that there are a host of
other devices with this issue, including iPods and some popular
cameras. I've not added quirks for them, since I don't have the
devices in front of me to test.
The patch from the PR was a little outdated w/regards to the
Vodafone vendor string.
PR: kern/106033
Submitted by: Volker Werth <volker_AT_vwsoft.com>
MFC in: 3 days
description here. The fix in the PR isn't necessary at all for memory
leaks, but we weren't setting the device description.
While I'm here, remove some of the obfuscating macros in attach.
PR: 108719
PR/108719, but there's a simpler fix: free it after it is used, and
then get rid of the redundant frees this causes. Other leaks in this
PR not yet fixed.
While I'm here, remove NetBSD/OpenBSD code and some of the portability
#defines that were getting in the way of understanding this code. The
devinfo bug was harder to spot because one needed to know that
device_set_desc_copy() was used inside of one of them (one that didn't
take an argument!).
Prefer device_printf(sc->sc_dev, "...") to printf("%s:...",
device_get_nameunit(sc->sc_dev)). This saves almost 300 bytes.
PR: 108719
Submitted by: Antoine Brodin
sparc64 GENERIC and the sound device drivers known working on sparc64
to use bus_get_dma_tag() to obtain the parent DMA tag so we can get rid
of the sparc64_root_dma_tag kludge eventually. Except for ath(4), sk(4),
stge(4) and ti(4) these changes are runtime tested (unless I booted up
the wrong kernels again...).
total size of all input reports is < 6.
PR: usb/106435
Submitted by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
Approved by: emax (mentor)
MFC after: 3 days
not needed if the proper ordering is done in attach and shutdown.
Remove usage of if_timer/watchdog and roll my own by piggybacking
off the tick() function.
Use the new usb system to allocate task queues instead of using
the system wide thread for taskqueues.
for usb. I hope that this will eventually be used for generic devices
that need full fledged blocking threads for event processing.
Create a taskqueue:
void usb_ether_task_init(device_t, int, struct usb_taskqueue *);
Enqueue a task:
void usb_ether_task_enqueue(struct usb_taskqueue *, struct task *);
Wait for all tasks queued to complete:
void usb_ether_task_drain(struct usb_taskqueue *, struct task *);
Destroy the taskqueue:
void usb_ether_task_destroy(struct usb_taskqueue *);
start working with third party usb modules, where sometimes it
is not easy to set the inclusion order so that there are no multiple
inclusions, yet you want to compile with high WARNS levels).
I am not sure if there is a standard for having a leading and/or trailing _
in the macro name, the usb code seems to use both.
There are still several unprotected headers here so it might be useful
to do the same thing on other files as well as the need arises.
MFC After: 3 days
The problem was that I was acquiring the driver sx lock and then waiting
for a taskqueue to drain, however the taskqueue itself would try to
acquire the lock as well leading to a deadlock.
To fix the problem roll my own exclusive lock that allows for lock
cancellation. This is a normal exclusive lock, however if someone
marks it as "dead" then all waiters who request an error return will
get back an error instead of continuing to wait for the lock.
In this particular case, the shutdown and detach functions kill the
lock while the async task thread tries to acquire the lock but will
abort if the lock returns an error.
The other option was to drop the driver lock mid-detach and mid-shutdown,
mid-detach was a ok, however mid-shutdown was not.
While I'm here, fix a bug in what appears to be the mii link status
word in the softc going out to lunch. Explicitly set the status
word to 1 after initializing the mii. This would result in an interface
that would never respond to "if_start" requests as the mii interface
would always look down.
aue_tick calls several synchronous usb functions from a timeout(9),
this is very broken since a timeout(9) is run as an interrupt
and the usb functions tsleep.
A stopgap fix is to schedule a taskqueue task from the timeout
and defer work to that taskqueue task.
an URQ_REQUEST when DMA segments are passed to usbd_start_transfer();
when the request doesn't include the optional data buffer the size of
the transfer (xfer->length) is 0, in which case usbd_transfer() won't
create a DMA map but call usbd_start_transfer() with no DMA segments.
With the previous change this could result in the bus_dmamap_sync()
implementation dereferencing the NULL-pointer passed as the DMA map
argument.
While at it fix what appears to be a typo in usbd_start_transfer();
in order to determine wheter usbd_start_transfer() was called with
DMA segments check whether the number of segments is > 0 rather than
the pointer to them being > 0.
OK'ed by: imp
I have been debugging the usb problems some more. Your were
right in your assumption (thanks for the pointer) about lack
of calls to bus_dmamap_sync(). In usbdi.c bus_dmamap_sync()
does get used for transfers that move data from PC to USB and
it is used for transfers that move data from USB to PC. But
someone forgot that control transfers consist of possibly two
data chunks : the request itself and optionally a buffer of
data that should be transfered to or from the USB device. On
requests to the control endpoint without additional data
bus_dmamap_sync() didn't get called. For some reason my first
tests with umass worked (due to enough cache poisening I
guess). The attached patch adds a call to bus_dmamap_sync()
to usbdi.c and now all devices I have tried work out of the
box. I have successfully transfered large files using the
if_axe driver and I have mounted several different umass
devices.
submitted by: Daan Vreeken
sponsored by: Vitsch Electronics
reviewed by: cognet@
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
: revision 1.27
: date: 2000/05/28 12:43:24; author: ache; state: Exp; lines: +3 -2
: Manipulate with AltGR Led (really CapsLock Led) only in K_XLATE mode, because
: all other modes not set ALKED flag and it means that CapsLock always turned
: off for them.
: Real bug example is X11 which never turn on CapsLock with Russian keyboard.
:
: PR: 18651
: Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
MFC after: 3 days
tasks. Since the host controllers rely on tasks to process transfer
timeouts, if a synchronous transfer from a driver was invoked from
a task and timed out, it would never complete because the single
task thread was stuck performing the synchronous transfer so couldn't
process the timeout.
This affected the axe, udav and ural drivers.
Problem hardware provided by: guido
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
close and re-open the default pipe instead of relying on the host
controller driver to notice the changes. Remove the unreliable code
that attempted to update these fields while the pipe was active.
This fixes a case where the hardware could cache and continue to
use the old address, resulting in a "getting first desc failed"
error.
PR: usb/103167
The parallel LINT build sometimes broke if kernel-depend wasn't
fast enough in generating ukbdmap.h. If someone thinks this
option would still be useful for the module, a proper fix is
to add the code generating ukbdmap.h into modules/ukbd/Makefile
and backing this change out.
ioctls passing integer arguments should use the _IOWINT() macro.
This fixes a lot of ioctl's not working on sparc64, most notable
being keyboard/syscons ioctls.
Full ABI compatibility is provided, with the bonus of fixing the
handling of old ioctls on sparc64.
Reviewed by: bde (with contributions)
Tested by: emax, marius
MFC after: 1 week
s/device_ptr_t/device_t/g
No md5 changes in the .o's
# Note to the md5 tracking club: $FreeBSD$ changes md5 after every commit
# so you need to checkout -kk to get $FreeBSD$ instead of the actual value
# of the keyword.
required by arches like sparc64 (not yet implemented) and sun4v where there
are seperate IOMMU's for each PCI bus... For all other arches, it will
end up returning NULL, which makes it a no-op...
Convert a few drivers (the ones we've been working w/ on sun4v) to the
new convection... Eventually all drivers will need to replace the parent
tag of NULL, w/ bus_get_dma_tag(dev), though dev is usually different for
each driver, and will require hand inspection...
Reviewed by: scottl (earlier version)
This enables the scanner function on these devices to be detected
and probed by uscanner(4), but only when ulpt is not loaded.
PR: usb/92462
Submitted by: Friedrich Volkmann
MFC after: 30 days
is never taken since there aren't any 802.11a ural(4) sticks available
on the market.
PR: kern/99676
Submitted by: KIYOHARA Takashi
Reviewed by: damien
MFC after: 1 week
- Curitel PC5740 Wireless Modem (Verizon's PCMCIA card)
- Sierra MC5720 Wireless Modem (Built in to Thinkpad X60s)
The scanner in the PR is already supported.
PR: 98908
Submitted by: Michael Collette <metrol@metrol.net>
blinks by default. When the operating system (read: normally an Xbox
360) initializes the gamepad, the LED stops blinking.
Change our uhid code to do the same.
PR: 97169
Submitted by: Ed Schouten <ed@fxq.nl>
device went away while open or if you tried to change the config
number while devices were open. Based on the patch from the PR with
a number of changes as discussed with the submitter.
PR: usb/97271
Submitted by: Anish Mistry
axe_cmd() calls. Without this the device can get confused if multiple
threads attempt these operations concurrently. The problem was
easily reproducible by running "ifconfig axe0" in a loop because
eventually it would conflict with axe_tick_task().
A similar approach is probably required in all USB ethernet drivers.
(1) bpf peer attaches to interface netif0
(2) Packet is received by netif0
(3) ifp->if_bpf pointer is checked and handed off to bpf
(4) bpf peer detaches from netif0 resulting in ifp->if_bpf being
initialized to NULL.
(5) ifp->if_bpf is dereferenced by bpf machinery
(6) Kaboom
This race condition likely explains the various different kernel panics
reported around sending SIGINT to tcpdump or dhclient processes. But really
this race can result in kernel panics anywhere you have frequent bpf attach
and detach operations with high packet per second load.
Summary of changes:
- Remove the bpf interface's "driverp" member
- When we attach bpf interfaces, we now set the ifp->if_bpf member to the
bpf interface structure. Once this is done, ifp->if_bpf should never be
NULL. [1]
- Introduce bpf_peers_present function, an inline operation which will do
a lockless read bpf peer list associated with the interface. It should
be noted that the bpf code will pickup the bpf_interface lock before adding
or removing bpf peers. This should serialize the access to the bpf descriptor
list, removing the race.
- Expose the bpf_if structure in bpf.h so that the bpf_peers_present function
can use it. This also removes the struct bpf_if; hack that was there.
- Adjust all consumers of the raw if_bpf structure to use bpf_peers_present
Now what happens is:
(1) Packet is received by netif0
(2) Check to see if bpf descriptor list is empty
(3) Pickup the bpf interface lock
(4) Hand packet off to process
From the attach/detach side:
(1) Pickup the bpf interface lock
(2) Add/remove from bpf descriptor list
Now that we are storing the bpf interface structure with the ifnet, there is
is no need to walk the bpf interface list to locate the correct bpf interface.
We now simply look up the interface, and initialize the pointer. This has a
nice side effect of changing a bpf interface attach operation from O(N) (where
N is the number of bpf interfaces), to O(1).
[1] From now on, we can no longer check ifp->if_bpf to tell us whether or
not we have any bpf peers that might be interested in receiving packets.
In collaboration with: sam@
MFC after: 1 month
USBD_FORCE_SHORT_XFER to ensure that we actually build and execute
a transfer. This means that the various alloc_sqtd_chain functions
will always construct a transfer, so it is safe to modify the
allocated descriptors on return. Previously there were cases where
a zero length transfer would cause a NULL dereference.
Reported by: bp
host controllers to avoid the need to allocate any multi-page
physically contiguous memory blocks. This makes it possible to use
USB devices reliably on low-memory systems or when memory is too
fragmented for contiguous allocations to succeed.
The USB subsystem now uses bus_dmamap_load() directly on the buffers
supplied by USB peripheral drivers, so this also avoids having to
copy data back and forth before and after transfers. The ehci and
ohci controllers support scatter/gather as long as the buffer is
contiguous in the virtual address space. For uhci the hardware
cannot handle a physical address discontinuity within a USB packet,
so it is necessary to copy small memory fragments at times.
EHCI spec for linking in new qTDs into an asynchronous QH. This
requires that there is a qTD marked as not active and not halted
at the start of the QH's list, and the hardware will know to re-fetch
the qTD on each pass rather than just looking at the overlay qTD:
"The host controller must be able to advance the queue from the
Fetch QH state in order to avoid all hardware/software race
conditions. This simple mechanism allows software to simply link
qTDs to the queue head and activate them, then the host controller
will always find them if/when they are reachable."
This is achieved by keeping an "inactivesqtd" entry on the QH list,
and re-using it each time as the start of the next transfer, and
allocating a new qTD to become the next inactivesqtd. Then a new
transfer can be activated by just setting its "active" flag, which
avoids all the previous messing with overlay qTD state in
ehci_set_qh_qtd().
before starting exploring (4 seconds), and extend the wait period
if new USB buses are attached while waiting.
This works around a problem seen when there is more than one EHCI
controller in the system and you kldload usb.ko after the system
has booted. The problem is that usb.ko contains 3 separate PCI
drivers which get initialised one by one (uhci, ohci, ehci), and
when each driver is initialised, all PCI buses are re-probed after
just the addition of that driver. This means that there can be a
significant delay between the attaching of a companion controller
and the subsequent EHCI attach, so it is possible for the companion
controller's USB 1.x bus to be scanned before the EHCI driver gets
a chance to check if there is really a USB 2.x device connected.
that have the specified kind, instead of assuming that there is
only one report of the right kind in the report descriptor.
Submitted by: Morten Johansen
Obtained from: NetBSD (indirectly)
PR: usb/77604
transfers. This fixes some cases where the software toggle tracking
was not doing the right thing. For example, a short transfer that
transferred 0 bytes of the requested qTD transfer size does cause
a toggle change, but the existing code was assuming it didn't.
Reported and tested by: pav
MFC after: 2 weeks
Developed with: Norbert Koch < NKoch at demig dot de >
No response from: freebsd-current@
Tested by: Norbert Koch < NKoch at demig dot de >
MFC after: 1 day
is closed and then reopened. This appears to be necessary now that
we no longer clear endpoint stalls every time a pipe is opened.
Previously we could assume an initial toggle value of zero because
the clear-stall operation resets the device's toggle state.
Reported by: Holger Kipp
MFC after: 3 days
try to use the registrant for numbers in this file, not the OEM that
put their label on it. Use PNY's real number 0x154b. Add another PNY
atachmate with quirks from a PR filed a while ago, but that I can't
seem to find now...
o fix contention window
o silently discard received frames that are too short
o simplify lookup of 802.11a channels (we know they exist)
o fix short preamble support
o add short slot support
o fix eifs settings
o many consistency tweaks
ATI EHCI controllers exhibit simmilar stall issues and require
this dropped interrupts workaround. Be verbose about it.
ehci.c:
ehcivar.h:
Slight change in comments to note about issues surrounding both
VIA and ATI EHCI controllers.
Approved by: iedowse
an interrupt appears to occur before the transfer has been marked
as completed. This caused umass transfers to get stuck, especially
when writing large files. The workaround sets up a timer that
rechecks for missed completed transfers if some operations are still
pending. Other suggested workarounds, such as performing a PCI read
immediately after acknowledging the interrupts, do not appear to
help.
Obtained from: OpenBSD
This is based on MCPC USB mobile phone guide line (MCPC-GL005)
Some other 3G system or so will work with this driver.
Kyocera PHS terminal (a.k.a. Kyopon) is known to work, which
is now supported by umodem(4) driver.
USB HID device that allows to plug two PS2 controllers. This specific
device doesn't work yet but will as soon as we support devices with
multiple report IDs.
MFC after: 3 days
broken report descriptor. While I'm here, make all the other report
descriptors const to match the newly added one.
Obtained from: NetBSD
MFC after: 1 week
lack a report descriptor and don't use the standard interface class.
This patch works around these deficiencies so that the uhid(4) driver
can recognize and use those broken devices.
PR: usb/90141
Submitted by: Ed Schouten <ed@fxq.nl> (with minor mods from me)
MFC after: 1 week
"done" method so that for non-repeat operations we have completely
finished with the transfer by the time the callback is invoked.
This makes it possible to recycle a transfer from within the callback
routine for the same transfer. Previously this almost worked, but
with OHCI controllers calling the "done" method after the callback
would zero out some important fields needed by the recycled transfer.
Only some usb peripheral drivers such as ucom appear to rely on the
ability to reuse a transfer from its callback.
MFC after: 1 week
appeared to rely on all kinds of non-guaranteed behaviours: the
transfer abort code assumed that TDs with no interrupt timeout
configured would end up on the done queue within 20ms, the done
queue processing assumed that all TDs from a transfer would appear
at the same time, and there were access-after-free bugs triggered
on failed transfers.
Attempt to fix these problems by the following changes:
- Use a maximum (6-frame) interrupt delay instead of no interrupt
delay to ensure that the 20ms wait in ohci_abort_xfer() is enough
for the TDs to have been taken off the hardware done queue.
- Defer cancellation of timeouts and freeing of TDs until we either
hit an error or reach the final TD.
- Remove TDs from the done queue before freeing them so that it
is safe to continue traversing the done queue.
This appears to fix a hang that was reproducable with revision 1.67
or 1.68 of ulpt.c (earlier revisions had a different transfer
pattern). With certain HP printers, the command "true > /dev/ulpt0"
would cause ohci_add_done() to spin because the done queue had a
loop. The list corruption was caused by a 3-TD transfer where the
first TD completed but remained on the internal host controller
done queue because it had no interrupt timeout. When the transfer
timed out, the TD got freed and reused, so it caused a loop in the
done queue when it was inserted a second time from a different
transfer.
Reported by: Alex Pivovarov
MFC after: 1 week
just discard the received frame and reuse the old mbuf.
This should prevent the connection from stalling after high network traffic.
MFC after: 2 weeks
from the printer and discarding the data even if the ulpt device
was opened for reading. This resulted in crashes because two
conconcurrent read transfers were using the same transfer structure.
PR: usb/88886
Reported By: Alex Pivovarov
MFC after: 1 week
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
---snip---
FYI this bit isn't needed for FreeBSD - I think it came from either
OpenBSD or NetBSD where arc4random() wasn't available during cold
boot.
---snip---
Explained by: iedowse
Synchronise with NetBSD upto rev 1.19:
- Allow 32 chars in the saved vendor string.
- Some NetBSD-only changes.
- Some missing parts (define, variable).
ehci_pci.c:
Add vendor ids for ATI and Philips.
Add identification strings for the following:
o ALi's M5239
o AMD 8111
o ATI SB200, SB400
o Intel 6300ESB, ICH4, ICH5, ICH7
o NVIDIA nForce 2, nForce 3, nForce 4
o Philips ISP156x
ehcireg.h:
We're at the same level as rev 1.18 from NetBSD.
usb_port.h:
NetBSD/OpenBSD specific things
Obtained from: NetBSD via DragonFly
No comment from: usb@
so that devd can match on it. This field was already available to
usbd and is used by a number of usbd.conf entries, so now it is
possible to transfer those entries to devd.conf.
Submitted by: Anish Mistry
o add ic_curchan and use it uniformly for specifying the current
channel instead of overloading ic->ic_bss->ni_chan (or in some
drivers ic_ibss_chan)
o add ieee80211_scanparams structure to encapsulate scanning-related
state captured for rx frames
o move rx beacon+probe response frame handling into separate routines
o change beacon+probe response handling to treat the scan table
more like a scan cache--look for an existing entry before adding
a new one; this combined with ic_curchan use corrects handling of
stations that were previously found at a different channel
o move adhoc neighbor discovery by beacon+probe response frames to
a new ieee80211_add_neighbor routine
Reviewed by: avatar
Tested by: avatar, Michal Mertl
MFC after: 2 weeks
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
when using mice containing a tilt movement: there was a missing
usb_callout_init() for the UMS_SPUR_BUT_UP quirk code, and UMS_T
was defined to the same flag value as UMS_SPUR_BUT_UP.
Reported by: flz
MFC after: 3 days
over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
through umass(4), in order to make cdcontrol(1) to issue commands to
a USB CD driver.
The command IDs were obtained from the CAM subsystem. This was tested
on half dozen of USB CD drivers from different vendors.
Suggested by: "intron" <intron at intron dot ac>
PR: usb/83439
Reviewed by: sanpei
MFC After: 1 week
succeed. There are many printers that return status over the read
channel, and if we wait for the status to become ready, then we can't
find the status automatically. Linux doesn't wait, nor does it ever
seem to really check the status in any meaningful way... If there
really is a problem, the writes to the bulk out endpoint will still
fail (like they would if the printer was ready and then ran out of
paper or became unready).
In addition, there are a number of printers being made that emulate
the 'status' byte by returning '0' always rather than '0x18'. This
fixes the EBUSY on open timeouts on those printer as well.
Reviewed by: the defining silence on usb@
o Indent usb ids properly
o Check the return value of if_alloc()
o Call if_free() in ural_detach()
Reviewed by: silby (mentor)
Approved by: re (scottl)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
are used onboard in most of the newer PCI-based sun4u machines
(cosmetic change as they were also already probed as generic OHCI
without this). Detect whether their intpin register is valid and
correct it if necessary, i.e. set the respective IVAR to the right
value for allocating the IRQ resource, as some of them come up
having it set to 0 (mainly those used in Blade 100 and the first
one on AX1105 boards). This fixes attaching affected controllers.
Correcting the intpin value might be better off in the PCI code
via a quirk table but on the other hand gem(4) and hem(4) also
correct it themselves and at least for the USB controller part
the intpin register is truely hardwired to 0 and can't be changed.
This means that we would have to hook up the quirk information
in a lot of places in the PCI code (i.e. whenever the value of the
intpin register is read from or written to the pci_devinfo of the
respective device) in order to do it the right way.
MFC after: 1 month
whether or not the receive pipe is stopped. This ensures that we
do not attempt to start the same transfer twice, and it allows
ucomstop() to skip the restarting of the read pipe if it was not
originally running, such as when called indirectly from ucomreadcb().
PR: kern/79420
MFC after: 1 day
This ensures that we explore EHCI busses before their companion
controllers' busses, so that ports connected to full/low speed
devices will be properly routed to the companion controllers by the
time the OHCI/UHCI exploration occurs.
found it guilty in putting the card into unusable state after UP->DOWN->UP
media status change.
Looks like some of register writes in this functions mess up PHY interface.
No visible regressions has been found after commenting this code out -
the card properly handles forceful local mode changes and auto-detects changes
made remotely (tested with Auto, 10HD, 10FD, 100HD, 100FD).
Sponsored by: PBXpress Inc.
MFC after: 3 days
with the wrong language parameter when retrieving the device serial
number. This invalid request caused some devices not to work at
all.
PR: usb/79190
Submitted by: Hans Petter Selasky <hselasky@c2i.net>
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
configure_final(), assert that "cold" is true in usb_cold_explore()
when there are busses to explore. When USB is kldloaded after boot,
usb_cold_explore() will still get invoked but the list of busses
to explore in that case should always be empty.
transfer, which lead to panics or page faults. For example if a
transfer timed out, another thread could come along and attempt to
abort the same transfer while the timeout task was sleeping in
the *_abort_xfer() function.
Add an "aborting" flag to the private transfer state in each host
controller driver and use this to ensure that the abort is only
executed once. Also prioritise normal abort requests over timeouts
so that the callback is always given a status of USB_CANCELLED even
if the timeout-initiated abort began first.
The crashes caused by this bug were mainly reported in connection
with lpd printing to a USB printer.
PR: usb/78208, usb/78986
system have been attached, but no later. This ensures that we do
not explore ohci or uhci busses before the companion echi controller
has been initialised, so it should fix the problem of multi-speed
USB devices getting attached as USB 1 devices first and then
re-attached as USB 2.
Some further changes are needed on architectures that do not currently
allow hooks to be inserted before configure_final() - alpha, ia64,
powerpc and sparc64. On these architectures the exploration will
now be delayed until the usb kthread runs.
cleared if the host controller retries the transfer and is successful,
but we were interpreting these bits as indicating a fatal error.
Ignore these error bits, and instead use the HALTED bit to determine
if the transfer failed. Also update the USBD_STALLED detection to
ignore these bits.
Obtained from: OpenBSD
between passes over a QH. Previously the accesses to a QH were
bunched together in time, so the interval was often much longer
than intended. This now appears to match the diagrams in the EHCI
spec, so remove the XXX comment.
ever working correctly: the code was linking the QHs together but
then immediately overwriting the "next" pointers. Oops. Also
initialise qh_endphub, since the EHCI spec says that we should
always set the pipe multiplier field to something sensible.
This appears to make basic split transactions work, so enable split
transactions for control, bulk and interrupt pipes (split isochronous
transfers are not yet implemented). It should now be possible to
use USB1 devices even when they are connected through a USB2 hub.
o usb_subr.c, add delta 1.119:
Move usb_get_string() and make it public.
o usbdi.c, bring on par with 1.106, this includes:
- Make an iterator abstraction for looping through all descriptors.
- Whine about not being able to figure out default language if we are debugging.
- Move usb_get_string() and make it public.
o usbdi.h, bring on par with 1.64, this includes:
- Make an iterator abstraction for looping through all descriptors.
- Move usb_get_string() and make it public.
o usbdi_util.c, bring on par with 1.42, this includes:
- Add usbd_get_protocol().
- Use NULL instead of 0.
- Fix (mostly harmless) typo.
- Move utility routine from uirda.c to usbdi_util.c.
o usbdi_util.h, bring on par with 1.31, this includes:
- Add usbd_get_protocol().
- Move utility routine from uirda.c to usbdi_util.c.
MFC after: 3 days
base transfer speed to CAM. The actual value used (40MB/s) is fairly
arbitrary, but assumes the same 33% overhead as was implied by the
1MB/s figure we used for USB1 devices.
1/ doesn't matter on most of our architectures
2/ will never happen unless we start queueing multiple trasactions
to a single endpoint at one time (which we do not allow yet).
If anyone has a big_endian machine with EHCI they might check this
if they are having problems with EHCI but it's unlikely even there..
Submitted by: Hans Petter Selasky <hselasky@c2i.net>
MFC after: 3 days
to remove a transaction from the async schedule. The previous method didn't
work well and led to the hardware writing to free'd buffers etc, as
it didn't always know that the transaction had been aborted.
Written after consultation with David Brownell who wrote the Linux
EHCI driver.
As part of this give the sqh structure a "previous" pointer.
MFC after: 1 week
rather than a softc pointer (with the bus structure at the start).
This is a non-functional change. It just helps when reading the code to
know that the ehci, ohci and uhci drivers share the bus structure, not the
entire softc.
ADVANCELOGIC->AVANCELOGIC (nothing in the tree uses it, so safe to do)
sort HAGIWARA vendor entry
sort ACTIONTAR vendor entry
Minor change to SYSTEMTALKS vendor entry.
Add $NetBSD$ in a comment at the top
Update copyright dates
Update header comment
Add some of the entries not present in FreeBSD's usbdevs file
Harmonize some descriptions with NetBSD where NetBSD's were shorter
More work needs to happen here, as there's many conflicting vendor
names. There's also more harmonization that can happen before that
problem is tackled.
This was inspired by recent discussions, but none of the patches
posted were consulted to produce this commit. Other, similar ones
will follow.
This is part of an ongoing cycle of commits on all the BSDs to
merge the USB vendor and device defintions..
A merge from OpenBSD is still pending.
Submitted by: barry bouwsma (freebsd-misuser@NOSPAM.dyndns.dk)
Obtained from: NetBSD
MFC after: 1 week
to better keep track of the total amoutn transferred during a
transfer. Seems similar to some code in the NetBSD version.
I notice they have incorporated matches from him so I don't know which
direction it went.
Submitted by: damien.bergamini@free.fr
Obtained from: patches to make the ueagle driver work
MFC after: 1 week
Now only things that are different between us and NetBSD show up.
Means that these files are more of NetBSD style in some places but
since thay are NetBSD files, um, that's ok.
Obtained from: NetBSD
MFC after: 1 week
backed out commits were trying to address: when cancelling the timeout
callout, also cancel the abort_task event, since it is possible that
the timeout has already fired and set up an abort_task.
reports of problems. The bug is probably that there are cases where
`xfer->timeout && !sc->sc_bus.use_polling' is not a suitable test
for an active timeout callout, so an explicit flag will be necessary.
Apologies for the breakage.
transfer timeouts that typically cause a transfer to be completed
twice, resulting in panics and page faults:
o A transfer completion interrupt could arrive while an abort_task
event was set up, so the transfer would be aborted after it had
completed. This is very easy to reproduce. Fix this by setting
the transfer status to USBD_TIMEOUT before scheduling the
abort_task so that the transfer completion code will ignore it.
o The transfer completion code could execute concurrently with the
timeout callout, leaving the callout blocked (e.g. waiting for
Giant) while the transfer completion code runs. In this case,
callout_stop() does not prevent the callout from running, so
again the timeout code would run after the transfer was complete.
Handle this case by checking the return value from callout_stop(),
and ignoring the transfer if the callout could not be removed.
o Finally, protect against a timeout callout occurring while a
transfer is being aborted by another process. Here we arrange
for the timeout processing to ignore the transfer, and use
callout_drain() to ensure that the callout has really gone before
completing the transfer.
This was tested by repeatedly performing USB transfers with a timeout
set to approximately the same as the normal transfer completion
time. In the PR below, apparently this occurred by accident with a
particular printer and the default timeout.
PR: kern/71491
just a convenience function to be called from debuggers that gets
compiled in when EHCI_DEBUG is defined. Move its declaration to
make this more obvious.
o Reduce the interrupt delay to 2 microframes.
o Follow the spec more closely when updating the overlay qTD in the QH.
o No need to generate an interrupt at the data part of a control
transfer, it's generated by the status transfer.
o Make sure to update the data toggle on short transfers.
o Turn the printf about needing toggle update into a DPRINTF.
o Keep track of what high speed port (if any) a device belongs to
so we can set the transaction translator fields for the transfer.
o Verbosely refuse to open low/full speed pipes that depend on
unimplemented split transaction support.
o Fix various typos in comments.
Obtained from: NetBSD
asynchronous. I realize that this means the custom application will
not work as written, but it is not okay to break most users of ugen(4).
The major problem is that a bulk read transfer is not an interrupt
saying that X bytes are available -- it is a request to be able to
receive up to X bytes, with T timeout, and S short-transfer-okayness.
The timeout is a software mechanism that ugen(4) provides and cannot
be implemented using asynchronous reads -- the timeout must start at
the time a read is done.
The status of up to how many bytes can be received in this transfer
and whether a short transfer returns data or error is also encoded
at least in ohci(4)'s requests to the controller. Trying to detect
the "maximum width" results in using a single buffer of far too
small when an application requests a large read.
Even if you combat this by replacing all buffers again with the
maximal sized read buffer (1kb) that ugen(4) would allow you to
use before, you don't get the right semantics -- you have to
throw data away or make all the timeouts invalid or make the
short-transfer settings invalid.
There is no way to do this right without extending the ugen(4) API
much further -- it breaks the USB camera interfaces used because
they need a chain of many maximal-width transfers, for example, and
it makes cross-platform support for all the BSDs gratuitously hard.
Instead of trying to do select(2) on a bulk read pipe -- which has
neither the information on desired transfer length nor ability to
implement timeout -- an application can simply use a kernel thread
and pipe to turn that endpoint into something poll-able.
It is unfortunate that bulk endpoints cannot provide the same semantics
that interrupt and isochronous endpoints can, but it is possible to just
use ioctl(USB_GET_ENDPOINT_DESC) to find out when different semantics
must be used without preventing the normal users of the ugen(4) device
from working.
New devicename is ttyy{unit}{port}
No callout devices created as there is no modemcontrol on these ports.
Add data structure to represent each port to avoid excessive array use.
from within umass_ufi_transform(). This includes the 12-byte commands
FORMAT_UNIT, WRITE_AND_VERIFY, VERIFY, and READ_FORMAT_CAPACITIES
(sorted in numerical order).
Reviewed by: ken, scottl
MFC after: 2 weeks
data endpoints. The control endpoint doesn't need read/write/poll
operations, and more importantly, the thread counts should be
separate so that the control endpoint can properly reference itself
while deleting and recreating the data endpoints.
* Add some macros that handle referencing/releasing devices, and use them
for sleeping/woken-up and open/close operations as apppropriate.
* Use d_purge for FreeBSD, and a loop testing the open status for all
the endpoints for NetBSD and OpenBSD, so that when the device is
detached, the right thing always happens.
restart the current waiting transfer. If this isn't done, the device's
next transfer (that we would like to do a short read on) is going to
return an error -- for short transfer.
* For bulk transfer endpoints, restore the maximum transfer length each
time a transfer is done, or the first short transfer will make all the
rest that size or smaller.
* Remove impossibilities (malloc(M_WAITOK) == NULL, &var == NULL).
to make sure the pipe is ready. Some devices apparently don't support
the clear stall command however. So what happens when you issue such
devices a clear stall command? Typically, the command just times out.
This, at least, is the behavior I've observed with two devices that
I own: a Rio600 mp3 player and a T-Mobile Sidekick II.
It used to be that after the timeout expired, the pipe open operation
would conclude and you could still access the device, with the only
negative effect being a long delay on open. But in the recent past,
someone added code to make the timeout a fatal error, thereby breaking
the ability to communicate with these devices in any way.
I don't know exactly what the right solution is for this problem:
presumeably there is some way to determine whether or not a device
supports the 'clear stall' command beyond just issuing one and waiting
to see if it times out, but I don't know what that is. So for now,
I've added a special case to the error checking code so that the
timeout is once again non-fatal, thereby letting me use my two
devices again.
This changes the naming of USB serial devices to: /dev/ttyU%d and
/dev/cuaU%d for call-in and call-out devices respectively. (Please
notice: capital 'U')
Please also note that we now have .init and .lock devices for USB
serial ports. These are not persistent across device removal. devd(8)
can be used to configure them on attachment time.
These changes also improve the chances of the system surviving if
the USB device is unplugged at an inconvenient time. At least we
do not rip things apart while there are any threads in the device
driver anymore.
Remove cdevsw, rely on the tty generic one.
Don't make_dev(), use ttycreate() which does all the magic.
In detach, do close procesing if we ripped things apart
while the device was open. Call ttyfree() once we're done
cleaning up.
select(2), and discovered to my horror that ugen(4)'s bulk in/out support
is horribly lobotomized. Bulk transfers are done using the synchronous
API instead of the asynchronous one. This causes the following broken
behavior to occur:
- You open the bulk in/out ugen device and get a descriptor
- You create some other descriptor (socket, other device, etc...)
- You select on both the descriptors waiting until either one has
data ready to read
- Because of ugen's brokenness, you block in usb_bulk_transfer() inside
ugen_do_read() instead of blocking in select()
- The non-USB descriptor becomes ready for reading, but you remain blocked
on select()
- The USB descriptor becomes ready for reading
- Only now are you woken up so that you can ready data from either
descriptor.
The result is select() can only wake up when there's USB data pending. If
any other descriptor becomes ready, you lose: until the USB descriptor
becomes ready, you stay asleep.
The correct approach is to use async bulk transfers, so I changed
the read code to use the async bulk transfer API. I left the write
side alone for now since it's less of an issue.
Note that the uscanner driver has the same brokenness in it.
panic on hub detach bugs that have been reported. This work around
detaches the device before deleting it. This changes the detach order
from in-order to pre-order. This avoids uhub's deleting the children
after its subdevs has been deleted.
This is only a workaround. This leads to a strange condition in the
device tree where attached devices are children of detached ones. I
really don't know what that's supposed to mean, but does violate my
sense of POLA. Fortunately, the violation is short lived, which is
why I'm going ahead and committing the work around.
# We really need to consider life w/o the multiple nested layers of
# compatibility macros. They make finding bugs like this *MUCH*
# harder.
Patch by: iadowse
MT5 before: next_release(5.3-BETA5) (unless someting better comes along)
redundant at this point and should be retired). Don't free subdevs if
we don't attach any devices. This was leaving stale device_t's
around. Don't touch the device if it isn't attached since the name
isn't meaningful then. Switch from strncpy (properly used) to
strlcpy.
From a patch submitted by Peter Pentchev
device_t instances when no driver attaches. They are left around, and
we need to remember them.
# The usbd_device_handle->subdevs[] array likely is completely bogus
# at this point, but one change at a time, since its removal will need
# to have similar code replace it extracted from newbus.
Part of the patch submitted by Peter Pentchev after an excellent
analysis of the underlying problems.
MFC After: 1 week
produced better results for a test program I had here, it didn't
substantially change the number of crashes that I saw. Both the old
code and the new code seemed to produce the same crashes from the usb
layer. Since the new code also solves a close() crash, go with it
until the underlying issues wrt devices going away can be addressed.
The reference counts are there to block detach until the sleepers in
read/write/ioctl have gotten out, not to prevent the open device from
going away. Restore the old behavior so that we have a chance to wake
up sleepers when the usb device goes away, so they can properly return
EIO back to the caller when this happens.
Otherwise, we have a guarnateed panic waiting to happen when a device
detaches with an active read channel.
This should be merged to 5 asap.
to RS232 bridges, such as the one found in the DeLorme Earthmate USB GPS
receiver (which is the only device currently supported by this driver).
While other USB to serial drivers in the tree rely heavily on ucom, this
one is self-contained. The reason for that is that ucom assumes that
the bridge uses bulk pipes for I/O, while the Cypress parts actually
register as human interface devices and use HID reports for configuration
and I/O.
The driver is not entirely complete: there is no support yet for flow
control, and output doesn't seem to work, though I don't know if that is
because of a bug in the code, or simply because the Earthmate is a read-
only device.
Without this, the device cannot detect the end of ethernet packets
whose size is a multiple of the USB packat size.
PR: kern/70474
Submitted by: Andrew Thompson <andy@fud.org.nz>
MFC after: 1 week
o reprobe children when a new driver is added to uhub
o fix the usbd_probe_and_attach to set the ivars to a malloc'd area, as well
as freeing the ivars on child destruction.
o Don't delete children that don't attach. Evidentally, the need to do this
is a common misconception.
o minor formatting foo that may violate style(9) at the moment, but keeps the
diffs against my p4 tree smaller.
This does not solve the ugen gobbling things up problem, but the fixes
I have for that expose bugs in other parts of the tree...
if_start routines cannot currently be entered without Giant. When
the kernel is running with debug.mpsafenet != 0, this will defer
if_start execution to a task queue thread holding Giant, which may
introduce additional latency, but avoid incorrect execution.
Suggested by: dfr
skip blocks that are too big by a factor of two or greater. This
avoids some cases of extremely inefficient memory use that can occur
when large (e.g. 64k) blocks on the free list get used when allocating
a 4k chunk of 64-byte fragments. Because fragments have their own
free list, the 60k difference got lost forever every time.
system BIOS to disable legacy device emulation as per the "EHCI
Extended Capability: Pre-OS to OS Handoff Synchronisation" section
of the EHCI spec. BIOSes that implement legacy emulation using SMIs
are supposed to disable the emulation when this procedure is performed.
to be particularly correct or optimal, but it seems to be enough
to allow the attachment of USB2 hubs and USB2 devices connected via
USB2 hubs. None of the split transaction support is implemented in
our USB stack, so USB1 peripherals will definitely not work when
connected via USB2 hubs.
Improve child_detached a little and make it conform better to
style(9). Also, improve comment about what we'll be doing in the
future about driver_added. Soon it will be possible to kldload usb
drivers and have them attach w/o a need to disconnect/reconnect them.
usbdi.c rev. 1.104, author: mycroft
ugen_isoc_rintr() may recycle the xfer immediately. Therefore, we
avoid touching the xfer after calling the callback in
usb_transfer_complete(). From PR 25960.
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
rev. 1.67, author: mycroft
Fix a byte order error.
rev. 1.68, author: mycroft
Adjust some silliness that was causing us to do extra work for
"frame list rollover" interrupts, which we pretty much ignore.
Obtained from: NetBSD
rev. 1.68, author: mycroft
Ignore a port error that happens to come in at the same time as a
connect status change. Some root hubs seem to report both.
Obtained from: NetBSD
bus interfaces. These interfaces use the FTDI chipset with different
Vendor and Product IDs.
Add two additional baud rate enumerations. The vehicle bus interfaces
use a baud rate of 2000000. Also add 3000000 as it is the other FTDI
baud divisor special case.
I've commited a slightly different patch from that provided in the PR as
I changed the matching code a bit yesterday.
Submitted by: Mike Durian <durian at shadetreesoftware.com>
PR: kern/67357
operations when the refcount doesn't protect the opens and closes. Fix
this, and don't actually let a time out happen: now ugen(4) devices do
not get freed out from under the programs with them open.
