g_io_speedup waits for the completion of the speedup request before proceeding
using biowait(), but check_clear_deps is called with the softdeps lock held
(which is non-sleepable). It's safe to drop this lock around the call to
speedup, so do that.
Submitted by: Peter Holm
Reviewed by: kib@
IPv4 and IPv6.
This fixes a regression issue after r349369. When trying to exit a
multicast group before closing the socket, a multicast leave packet
should be sent.
Differential Revision: https://reviews.freebsd.org/D22848
PR: 242677
Reviewed by: bz (network)
Tested by: Aleksandr Fedorov <aleksandr.fedorov@itglobal.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
While a given ACPI device may have 0-N compatibility IDs, in practice most
seem to have 0 or 1. If one is present, emit it as part of the PNP info
string associated with a device. This could enable MODULE_PNP_INFO-based
automatic kldload for ACPI drivers associated with a given _CID (but without
a good _HID or _UID identifier).
Reviewed by: imp, jhb
Differential Revision: https://reviews.freebsd.org/D22846
I've opted for just duplicating the two entries needed for this, rather than
writing any other mechanism for maintaining two root compat entries to map
to one config, for simplicity. We'll eventually declare these legacy DTB
unsupported, but let's not do that yet while there's no real burden.
While here, add RFC numbers to comments about nonce and AAD data
for TLS 1.2.
Reviewed by: gallatin
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D22801
We use armv7/GENERIC for the RPI2 images. The original RPI2 is actually a
32-bit BCM2836, but v1.2 was upgraded to the 64-bit BCM2837. The project
continues to provide the RPI2 image as armv7, as it's the lowest common
denominator of the two. Historically, we've just kind of implicitly
acknowledged this by including some bcm2837 bits on a SOC_BCM2836 kernel
config -- this worked until r354875 added code that actually cared.
Acknowledge formally that BCM2837 is valid in arm32.
This name is inconsistent with the other BCM* SOC on !arm64 for two reasons:
1. It's a pre-existing option on arm64, and
2. the naming convention on arm/ should've arguably changed to include BRCM
#1 seems to be a convincing enough argument to maintain the existing name
for it.
There are probably bits that are still wrong, but this fixes some
things at least:
- Add named arguments to the functions in crypto(9).
- Add missing algorithms.
- Don't mention arguments that don't exist in crypto_register.
- Add CIOGSESSION2.
- Remove CIOCNFSESSION.
- Clarify some stale language that assumed an fd had only one sesson.
- Note that you have to use CRIOGET and add a note in BUGS lamenting
that one has to use CRIOGET.
- Various other cleanups.
Reviewed by: cem (earlier version)
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D22784
While it works on nda, it fails on ada and/or da for at least zfs with a modify
after free issue on a trim BIO. Revert while I rework it to fix those devices.
SIOCGAIRONET allows userspace to query an(4) for various device
properties and configuration, which appears to potentially include
sensitive information such as WEP keys (an(4) seems to predate WPA).
Also avoid races by copying in the request structure to a temporary
buffer before locking and modifying the device softc.
Reported by: Ilja Van Sprundel <ivansprundel@ioactive.com>
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
gets both rack and bbr ready for the completion of the STATs
framework in FreeBSD. For now if you don't have both NF_stats and
stats on it disables them. As soon as the rest of the stats framework
lands we can remove that restriction and then just uses stats when
defined.
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D22479
It used to be required that a device be a child of gpiobus(4) to manipulate
gpio pins. That requirement didn't work well for FDT-based systems with many
cross-hierarchy users of gpio, so a more modern framework was created that
removed the old hierarchy requirement.
These changes adapt the owc_gpiobus driver to use the newer gpio_pin_*
functions to acquire, release, and manipulate gpio pins. This allows a
single driver to work for both hinted-attachment and fdt-based systems, and
removes the requirement that any one-wire fdt nodes must appear at the root
of the devicetree.
Differential Revision: https://reviews.freebsd.org/D22710
The maxpin counter starts at 0, fix one by one error.
This is still not totally correct for some banks in some SoC that have
fewer pins but this will be dealt with in another commit.
MFC after: 3 days
r351187 change the SYSCON_WRITE to SYSCON_MODIFY but didn't changed the
mask variable that used to hold the bitmask in the upper 16 bits of the
register that control which bits are changed. So we ended up clearing
bit from the upper 16bits half which are always 0 after a read.
Use the correct bit mask for bits that we want to clear.
MFC after: 3 days
From UEFI specification 2.8, page 434:
"It should also be noted that certain input devices may not be able to produce
shift or toggle state information, and in those cases the high order bit in
the respective Toggle and Shift state fields should not be active."
But we still need to check for ScanCode and UnicodeChar.
PR: 242660
Reported by: Trond Endrestol
MFC after: 1 week
Nothing modifies these things, but const'ify out of an abundance of caution.
If we could const'ify the definition in each keyboard driver, I likely
would- improper mutations here can lead to misbehavior or slightly more
annoying to debug state.
React to the BIO_SPEED command in the cam io scheduler by completing
as successful BIO_DELETE commands that are pending, up to the length
passed down in the BIO_SPEEDUP cmomand. The length passed down is a
hint for how much space on the drive needs to be recovered. By
completing the BIO_DELETE comomands, this allows the upper layers to
allocate and write to the blocks that were about to be trimmed. Since
FreeBSD implements TRIMSs as advisory, we can eliminliminate them and
go directly to writing.
The biggest benefit from TRIMS coomes ffrom the drive being able t
ooptimize its free block pool inthe log run. There's little nto no
bene3efit in the shoort term. , sepeciall whn the trim is followed by
a write. Speedup lets us make this tradeoff.
Reviewed by: kirk, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18351
When we have a resource shortage in UFS, send down a BIO_SPEEDUP to
give the CAM I/O scheduler a heads up that we have a resource shortage
and that it should bias its decisions knowing that.
Reviewed by: kirk, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18351
Add BIO_SPEEDUP bio command and g_io_speedup wrapper. It tells the
lower layers that the upper layers are dealing with some shortage
(dirty pages and/or disk blocks). The lower layers should do what they
can to speed up anything that's been delayed.
The first use will be to tell the CAM I/O scheduler that any TRIM
shaping should be short-circuited because the system needs
blocks. We'll also call it when there's too many resources used by
UFS.
Reviewed by: kirk, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18351
Rather than a trim active flag, have a counter that can be used to
have a absolute limit on the number of trims in flight independent of
any I/O limiting factors.
Sponsored by: Netflix
For each of the different queue types, list the name of the
queue. While it can be worked out from context, this makes it more
useful and clearer.
Sponsored by: Netflix
Add rate limiters to trims. Trims are a bit different than reads or
writes in that they can be combined, so some care needs to be taken
where we rate limit them. Additional work will be needed to push the
working rate limit below the I/O quanta rate for things like IOPS.
Sponsored by: Netflix
Add two sysctls to control pacing of nvme
trims. kern.cam.nda.X.goal_trim is the number of upper layer
BIO_DEELETE requests to try to collecet before sending TRIM down too
the nvme drive. trim_ticks is the number of ticks, at mosot, to wait
for at least goal_trim BIOS_DELEETE requests to come in.
Trim pacing is useful when a large number off disjoint trims are
comoing in from the upper layers. Since we have no way to chain
toogether trims from the upper layers that are sent down, this acts as
a hueristic to group trims into reasonable sized chunks. What's
reasonable varies from drive to drive.
Sponsored by: Netflix
This looks like a bit of debugging code that sliped into the initial
import of the new ATA framework. This changes the behavior to omit a
line of output that appears to have been intended for omission.
Reviewed by: mav
MFC after: 3 days
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22845
So it turns out that sometime in the past I removed the GPIO bits here
and was going to move it into a module in order to save a little space.
However, it turns out that was a mistake on this particular AP - it
uses a pair of GPIO lines to control the two receive LNAs on the 2GHz
radio and without them enabled the radio is a LOT DEAF.
With this re-introduced (and some replacement userland tools to save
space, *cough* cpio/libarchive) I can actually use these chipsets
again as a 2G station. Without the LNA the AP was seeing a per-radio
RSSI upstairs here of around 3-5dB, with the LNA on it's around 15dB,
more than enough to actually use wifi upstairs and also in line with
the other Atheros / Intel devices I have up here.
Big oopsie to Adrian. Big, big oopsie.
As modern software keeps growing in size, we get requests to update the
value of ARG_MAX in order to link the resulting object files. Other OSs
have much higher values but Increasiong ARG_MAX has a multiplied effect on
KVA, so just bumping this value is dangerous in some archs like ARM32 that
can exhaust KVA rather easily.
While it would be better to have a unique value for all archs, other OSs
(Illumos in partidular) can have different ARG_MAX limits depending on the
platform, For now we want to be really conservative so we are avoidng
the change on ILP32 and in the alternative case we only double it since that
seems to work well enough for recent Code Aster.
I was planning to bump the _FreeBSD_version but it was bumped recently
(r355798) so we can reuse the 1300068 value for this change.
PR: 241710
MFC after: 5 days
- PCI_MASK_CONFIG(sc->dev, CBBR_BRIDGECTRL,
- & ~CBBM_BRIDGECTRL_INTR_IREQ_ISA_EN, 2);
was accidentally dropped from r355822 in the refactor. Restore it since 16-bit
cards may fail without it (some bridges autodetect this properly, so my laptop
worked when I tested it).
Noticed by: rpokala@
- Move libxo.a build to subdirectory (lib/libxo/libxo/Makefile)
- Add .WAIT target to delay encoder build til after libxo
- Use FILES to install encoder library as csv.enc
- Update import script to put xo_config.h in new location
For all the INT13 calls, use symbolic names instead of magic numbers. This makes
it easier to understand what the code is doing w/o a trip to google to find what
these numbers mean.
array with a singleton.
Also, pccbb isa attachment is never going to happen, do disconnect it from the
build (will delete this in future commit). It would need to be updated as well,
but since this code is effectively dead code, remove it from the build instead.
fix an assert violation introduced in r355784. Without this spinlock_exit()
may see owepreempt and switch before reducing the spinlock count. amd64
had been optimized to do a single critical enter/exit regardless of the
number of spinlocks which avoided the problem and this optimization had
not been applied elsewhere.
Reported by: emaste
Suggested by: rlibby
Discussed with: jhb, rlibby
Tested by: manu (arm64)
than "/compat/linux". Useful when you have several compat directories
with different Linux versions and you don't want to clash with files
installed by linux-c7 packages.
Reviewed by: bcr (manpages)
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D22574
