Back out r203140 which was causing problems when the first and the last
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
If a USB device is suspended and a USB set config request is issued when the
USB enumeration lock is locked, then the USB stack fails to resume the device
because locking the USB enumeration lock is part of the resume procedure. To
solve this issue a new lock is introduced which only protects the suspend and
resume callbacks, which can be dropped inside the usbd_do_request_flags()
function, to allow suspend and resume during so-called enumeration operations.
SiS190 supports RX 10 bytes padding, CRC stripping as well as VLAN
hardware tag insertion/stripping. Remove conditional code that
disables these hardware features on SiS190. Also nuke RX fixup code
which is no more required on strict-alignment architectures because
SiS190 supports RX 10 bytes padding.
Now all hardware features except jumbo frame and WOL are supported.
Thanks to Masa Murayama who confirmed SiS190 also has the same
hardware features of SiS191.
I guess the only difference between SiS191 and SiS190 would be
jumbo frame support. It will be implemented in near future.
Implement TSO and TSO over VLAN. Increase number of allowed
fragmentation of mbuf chain to 32 from 16 because TSO can send 64KB
sized packet which in turn requires long list of mbuf chain. Due to
lack of documentation, I'm not sure whether driver have to pull up
ethernet/IP/TCP header with options to make controller work but
driver have to parse TCP header to update pseudo TCP checksum
anyway. The controller expects pseudo TCP checksum computed by
upper stack and the checksum should follow the MS NDIS
specification to make TSO work.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
Export hardware MAC statistics through sysctl node. Previously
fxp(4) already used to extract most hardware MAC statistics but it
didn't show them. With this change, all MAC statistics counters
are exported. Because there are a couple of new counters for 82558
and 82559, enable extended MAC statistics functionality to get
these counters. Accoring to public data sheet, 82559 MAC statistics
return 24 DWORD counters(3 counters are unknown at this moment) so
increase MAC counter structure to meet the MAC statistics block size.
The completion of MAC counter dump is now checked against
FXP_STATS_DR_COMPLETE status code which is appended at the end of
status block. Previously fxp(4) ignored the status of the
FXP_SCB_COMMAND_CU_DUMPRESET command. fxp(4) does not wait for the
completion of pending command before issuing
FXP_SCB_COMMAND_CU_DUMPRESET. Instead it skips the command and try
it next time. This scheme may show better performance but there is
chance to loose updated counters after stopping controller. So make
sure to update MAC statistics in fxp_stop().
While I'm here move sysctl node creation to fxp_sysctl_node().
Tested by: Larry Baird < lab <> gta dot com >
8255x configure command requires number of bytes of configuration
table. The default size of the configuration table was 22 bytes. To
use extended feature of 82550/82551 the configuration table size
was expanded to 32 bytes. The added configuration for 82550/82551
specifies VLAN hardware tagging and IPSec configuration as well as
TCO.
To make configuration easier fxp(4) used a configuration template
and the template was copied to configuration table. After that,
some parameters of the configuration table was changed depending on
controller type and operation mode. However the size of template
was 22 bytes so some configuration parameters were not properly
initialized on 82550/82551.
Fix this by increasing the template size. For 82557, 82558 and
82559 the size of the configuration is still 22 bytes.
- Don't set CAS_PCS_DATAPATH to anything except CAS_PCS_DATAPATH_SERDES
on Cassini using the external PCS SERDES otherwise unaligned access
traps and other strange effects happen with some machines. Don't touch
the MIF which is unused in that case either. These changes require the
PHY type to use to be determined via the OFW device tree or from the
VPD in machines without the former.
- Disable the SERDES pins of Saturn when not used in order to save power
and ensure they are enabled otherwise.
- In cas_attach() use the correct register offset for CAS_PCS_CONF_EN.
- Add some bus space barriers missing in the PCS code path.
These changes make the Sun GigaSwift Ethernet 1.0 MMF cards as well as
the on-board interfaces found in Sun Fire B100s Blade Server work.
PR: 144867
r207639: Add IFCAP_LINKSTATE to cxgb
r207643: T3 hardware filters + cxgbtool interface to this functionality.
r207687: if_cxgb should not depend on the T3 firmware module directly.
r207688: various doorbell adjustments
It seems controller has two types of promiscuous control, one for
unicast and the other for multicast. To receive multicast frames
that host didn't join in promiscuous mode, driver have to set
promiscuous mode for multicast frames as well.
The Open Source Software Developer Manual for i8255x was not clear
how to handle promiscuous mode.
PR: kern/145905
Add a workaround for a bug in the firmware regarding the transition
from passive to active scans. Basicly disable it by increasing the
amount packets to be received to an amount which can't be reached
during dwell times.
Approved by: rpaulo (mentor)
r207622:
Drop driver lock before exiting from interrupt handler.
r207623:
Make sure to check whether driver is running before processing
received frames. Also check driver has valid ifp pointer before
calling msk_stop() in device_shutdown handler. While I'm here
remove unnecessary accesses to interrupt mask registers in
device_shutdown handler because driver puts the controller into
reset state.
With these changes, msk(4) now survive from heavy RX traffic(1byte
UDP frame) while reboot is in progress.
r207638:
When VLAN hardware tagging is disabled, make sure to disable VLAN
checksum offloading as well as TSO over VLAN.
r207628:
Enable multi-descriptor transmisstion for fragmented mbufs. There
is no more need to defragment mbufs. After transmitting the
multi-fragmented frame, the controller updates only the first
descriptor of multi-descriptor transmission so it's driver's
responsibility to clear OWN bits of remaining descriptor of
multi-descriptor transmission. It seems the controller behaves much
like jme(4) controllers in descriptor handling.
r207635:
Free entire mbuf chain instead of the first mbuf.
- Remove dead code. Calculated greatest common divisor was not used at all.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
On sparc64 obtain the initiator ID to be used for SPI HBAs from the
Open Firmware device tree in order to match what the PROM built-in
driver uses. This is especially important when netbooting Fujitsu
Siemens PRIMEPOWER250 as in that case the built-in driver isn't used
and the port facts PortSCSIID defaults to 0, conflicting with the
disk at the same address.
- On sparc64 obtain the initiator ID from the Open Firmware device tree
in order to match what the PROM built-in driver uses.
- Remove some no longer used includes.
r207545:
Fix wrong dma tag usage. Previously it used TX descriptor ring dma
tag which should be TX mbuf dma tag.
r207625:
Remove clearing RxHashTable2 register. The register is reprogrammed
in sge_rxfilter().
Make SATA XPT negotiate and enable some additional SATA features, such as:
- device initiated power management (some devices support only this way);
- Automatic Partial to Slumber Transition (more power saving);
- DMA auto-activation (expected to slightly improve performance).
More features could be added later, when hardware supports.
r207409:
Both RX_GMF_LP_THR and RX_GMF_UP_THR must be 16 bits register. If
it is 8bits register then RX FIFO size can't exceed 2KB which is
not true for almost all Yukon II controller.
r207442:
Disable non-ASF packet flushing on Yukon Extreme as vendor's driver
does. Without this change, Yukon Extreme seems to generate lots of
RX FIFO overruns even though controller has available RX buffers.
These excessive RX FIFO overruns generated lots of pause frames
which in turn killed devices plugged into switch. It seems there is
still occasional RX frame corruption on Yukon Extreme but this
change seems to fix the pause frame storm.
Reported by: jhb
Tested by: jhb
Enable VLAN hardware tag insertion/stripping. Due to lack of SiS190
controller, I'm not sure whether this is also applicable to SiS190
so this feature is only activated on SiS191 controller.
In theory, controller reinitialization is not needed when VLAN tag
configuration is changed, but xclin said controller was not stable
whenever toggling VLAN tag bit. To address that, sge(4)
reinitialize controller for VLAN configuration which seems to work
as expected. VLAN tag information for TX/RX descriptor and
configure bit of RxMacControl register was found by xclin.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw > (initial version)
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
Enable FCS stripping and padding 10 bytes bit of RX MAC control
register. Due to lack of SiS190 controller, I'm not sure whether
this is also applicable to SiS190 so this feature is only activated
on SiS191 controller.
The controller can pad 10 bytes before DMAing a received frame to
RX buffer and received bytes include the padded bytes. This padding
is very useful on strict-alignment architectures because driver
does not have to copy received frame to align IP header on 4 bytes
boundary. It also gives better RX performance on non-strict
alignment architectures. Special thanks to xclin to give me
valuable register information. Without his enthusiastic trial and
errors this wouldn't be even possible.
While I'm here tighten validity check of received frame. Controller
clears RDS_CRCOK bit when it received bad CRC frames. xclin found
that using loop back testing.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
r207375:
Preserve unknown bits of RX MAC control register when driver
programs RX filter configuration. It seems RX MAC control register
is one of key registers to get various offloading features as well
as performance. Blindly clearing unrelated bits can result in
unexpected results.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
r207376:
Remove wrong link state chage.
r207377:
Explicitly marks SiS190 to differentiate it from SiS191.
