This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
- Ring the correct doorbell when streams mode is used.
- Wrap one or two long lines.
Tested by: Markus Pfeiffer (DragonFlyBSD)
MFC after: 1 week
DWC OTG driver. Fix a hang issue when using LOW and FULL speed
BULK traffic. Make sure we don't ask for data in the last
microframe. This allows using devices like USB mice and USB
keyboards connected to the RPI-B.
Suggested by: gonzo @
the 'PREVENT/ALLOW MEDIUM REMOVAL' SCSI command. An example of such a
device is the STmicro ST72682. We send the SCSI command for every open and
close, which can result in a significant amount of spam on the console
during boot.
Reviewed by: hps@
temporarily stores characters if the TTY buffer is full when
used a as a console. This can happen when a console is suspended.
Also properly do the flow stop signalling when this happens and
flow start when the condition changes back to normal again.
Bump __FreeBSD_version to force external kernel modules
to be recompiled. No kernel API changes.
MFC after: 1 week
Suggested by: ed @
to the initial SCSI INQUIRY command, enable all quirks.
This fixes detection of some Transcend TS2GUFM devices.
MFC after: 1 week
Reported by: Michael Dexter
Also update the port reset time from 250ms to 50ms. Some USB devices
have a hard limit in hardware at 222ms for the port reset time and will
not enumerate unless this delay is closer to the usb.org defined value.
This patch can fix enumeration with some USB devices.
Tested by: Guido van Rooij
Submitted by: Nick Hibma
MFC after: 1 week
now use function calls:
if_clone_simple()
if_clone_advanced()
to initialize a cloner, instead of macros that initialize if_clone
structure.
Discussed with: brooks, bz, 1 year ago
and Sierra Wireless MC8790V. Also implement the .ucom_poll method.
Note: This makes it possible to use lqr/echo in ppp.conf. And it
resolves ppp hanging during the PPp> phase.
Reviewed by: hps
MFC after: 1 week
set not-NULL during SIM registration and set to UMASS_GONE on destruction.
Debug messages there look broken for at least 9 years, as they dereference
softc value that was just checked to be equal to NULL.
- Remove magic pointer value UMASS_GONE and use simple NULL instead.
Found by: Clang Static Analyzer
gone rule. Optimise use of channels so that when a channel
is not ready another channel is used. Instead of using the SOF interrupt
use the system timer to drive the host statemachine. This might
give lower throughput and higher latency, but reduces the CPU usage
significantly. The DWC OTG host mode support should not be considered
for serious USB host controller applications. Some problems are still
seen with LOW speed USB devices.
of the DWC OTG is very simple in PIO mode, and we need to re-transmit
data when NAK is received among other things. We probably will need
to implement some kind of rate limitation on the NAK-ing.
The DWC OTG host mode support should still be considered
experimental. Isochronous support for DWC OTG is not
fully implemented. Some code added derives from
Aleksandr Rybalko's dotg.c driver.
"device_free_softc()" and "device_claim_softc()",
to allow USB serial drivers refcounting the softc.
These functions are used to grab the softc from
auto-free and to free the softc back to the correct
malloc type, respectivly.
Discussed with: jhb
MFC after: 2 weeks
make maintaining this driver from the documentation easier in the future.
This is a mostly mechanical change.
In uslcom_param(), move the zeroing of the final two fields of the
flowctrl structure outside of the "if CRTSCTS" section - not only were
they being zeroed in both the clauses, but these two fields have nothing
to do with hardware flow control anyway.
in SUPER-speed mode, USB 3.0.
This feature has not been tested yet, due to lack of hardware.
This feature is useful when implementing protocols like UASP,
USB attached SCSI which promises higher USB mass storage throughput.
This patch also implements support for hardware processing of endpoints
for increased performance. The switching to hardware processing
of an endpoint is done via a callback to the USB controller driver. The
stream feature is implemented like a variant of a hardware USB protocol.
USB controller drivers implementing device mode needs to be updated to
implement the new "xfer_stall" USB controller method and remove the
"xfer" argument from the "set_stall" method.
The API's toward existing USB drivers are preserved. To setup a USB transfer
in stream mode, set the "stream_id" field of the USB config structure to
the desired value.
The maximum number of BULK streams is currently hardcoded and limited to 8
via a define in usb_freebsd.h.
All USB drivers should be re-compiled after this change.
LibUSB will be updated next week to support streams mode. A new IOCTL to
setup BULK streams as already been implemented. The ugen device nodes
currently only supports stream ID zero.
The FreeBSD version has been bumped.
MFC after: 2 weeks
the device_detach() function doesn't block on UCOM device
drivers until the TTY handle is closed by the userspace
application. This is implemented by a postpone of the
softc free where the UCOM structures reside until the
TTY references are gone.
Discussed with: kib, ed
MFC after: 2 weeks
Extend the callback table of UCOM to include a
"ucom_free" function pointer which is called when
all refs on a UCOM super structure is gone.
Implement various helper functions to handle
refcounting and draining on the UCOM super
structure.
Implement macro which can be used in device
drivers to avoid module unload before all
pending TTY references are gone.
The UCOM API is backwards compatible after this
change and device drivers require no changes
to function with this change. Only a recompilation
of UCOM device drivers is required. The FreeBSD
version has been bumped in that regard.
Discussed with: kib, ed
MFC after: 2 weeks
that the wrong UART reference clock will be used for a few of the IDs.
It is currently not possible to figure that out because the Linux FTDI
driver detects this run-time and not compile time based on the bcdDevice
field of the USB device descriptor. Some of the ID's in usbdevs are not
sorted according to the product ID value. Please feel free to fix this.
I'm out of my xemacs magic today.
This syncronises us with the linux kernel at kernel.org (HEAD).
MFC after: 2 weeks
Use the interface number from the USB interface descriptor
like in the other USB serial drivers. These numbers are not
supposed to be different, though in theory they can. Make sure
that the driver then uses the interface number given by the USB
descriptor, and not the logical index of the USB stack.
For the future:
Whenever the term "index" is used in the USB code, it refers to
a number computed by the USB stack.
Whenever the term "number" is used in the USB code, it refers to
a number in a USB descriptor.
MFC after: 2 weeks
support for only the first port, but the CP2105 can have multiple ports.
Although this allowed the first port to mostly work on multi port devices,
there could be issues with this arrangement.
Update the man page to reflect support for both ports and the CP2105.
Many thanks to Silicon Labs (www.silabs.com) for providing a CP2105-EK
dev board for testing.
MFC after: 2 weeks
list of supported devices with the union of:
NetBSD src/sys/dev/usb/uslsa.c 1.18
OpenBSD src/sys/dev/usb/uslcom.c 1.24
Linux source/drivers/usb/serial/cp210x.c HEAD
Remove duplicate JABLOTRON PC60B entry.
Note that some of the devices added here are multi-port devices. The
uslcom(4) driver currently only supports the first port on such devices.
Update the man page to reflect the full list of supported devices.
Remove two caveats from the CAVEATS section, as both listed caveats no
longer apply. Add a caveat about multi-port devices.
MFC after: 2 weeks
- The USLCOM_SET_BAUD_DIV command (0x01)
- The USLCOM_SET_BAUD_RATE command (0x13)
Devices based on the CP1204 will only accept the latter command, and ignore
the former. As the latter command works on all chips that this driver
supports, switch to always using it.
A slight confusion here is that the previously used command was incorrectly
named USLCOM_BAUD_RATE - even though we no longer use it, rename it to
USLCOM_SET_BAUD_DIV to closer match the name used in the datasheet.
This change reflects a similar change made in the Linux driver, which was
submitted by preston.fick at silabs.com, and has been tested on all of the
uslcom(4) devices I have to hand.
MFC after: 2 weeks
one device (support for Motorola cables), this syncronises us with:
OpenBSD src/sys/dev/usb/uplcom.c 1.56
NetBSD src/sys/dev/usb/uplcom.c 1.73
Linux kernel.org HEAD
MFC after: 1 week
The function keys on a Microsoft Natural Egronomic Keyboard 4000 have been
repurposed as "Help", "Undo", "Redo" etc., and a special "F Lock" key is
required to return them to their normal purpose.
This change enables the UQ_KBD_BOOTPROTO quirk for the MS Natural 4000
keyboard to get the keys working again. More extensive changes to the USB
keyboard infrastructure would be needed to fully support the "F Lock" mode
and the extended keys on this keyboard.
PR: usb/116947
Approved by: hselasky@
This includes adding support for skipping FTDI interfaces used for JTAG
leaving them for userland and just attaching to the RS232 half, similarly
to how the corresponding Linux drivers handles these kind of adapters.
While at it, sort uftdi_devs and return BUS_PROBE_SPECIFIC (because
uftdi_probe() alters the instance variables for better or worse as do
other probe routines of USB drivers) instead of 0.
- Remove duplicated entries for BeagleBone.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Remove some stray lines.
MFC after: 3 days
Supermicro LCD screen modules seem to not support accessing reports through
the control pipes, but working fine with the interrupt pipes.
Sponsored by: iXsystems, Inc.
MFC after: 1 week
deterministically handled after the corresponding PHY drivers when
loaded as modules. Otherwise, when these MAC/PHY driver pairs are
compiled into a single module probing the PHY driver may fail. This
makes r151438 and r226154 actually work. [1]
Reported and tested by: yongari (fxp(4))
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
Submitted by: jhb [1]
MFC after: 3 days
This will give you more bandwidth for isochronous
FULL speed applications connected through a
High Speed HUB.
This patch has been tested with XHCI and EHCI.
MFC after: 1 week
and not asynchronously. This fixes problems related to USB system
suspend and resume. It is assumed that we are always allowed to sleep
from the device_suspend() method.
MFC after: 1 week
Submitted by: jkim
Code should just use the devtoname() function to obtain the name of a
character device. Also add const keywords to pieces of code that need it
to build properly.
MFC after: 2 weeks
primitives by breaking stop_scheduler into a per-thread variable.
Also, store the new td_stopsched very close to td_*locks members as
they will be accessed mostly in the same codepaths as td_stopsched and
this results in avoiding a further cache-line pollution, possibly.
STOP_SCHEDULER() was pondered to use a new 'thread' argument, in order to
take advantage of already cached curthread, but in the end there should
not really be a performance benefit, while introducing a KPI breakage.
In collabouration with: flo
Reviewed by: avg
MFC after: 3 months (or never)
X-MFC: r228424
Currently the code is not built by any modules. That will
be fixed later. The Atmel ARM bus interface file part of this
commit is just for sake of example. All registers and bits are
declared like macros and not C-structures like in official
Synopsis header files. This driver mostly origins from the
musb_otg.c driver in FreeBSD except that the chip specific
programming has been replaced by the one for DWC 2.0 USB OTG.
Some parts related to system suspend and resume have been left
like empty functions for the future. USB suspend and resume is
fully supported.
This change is designed to let USB keyboard work in the panic context
with stop_scheduler_on_panic=1. Most of change consists of removing
mtx_owned() checks where they can be easily avoided. Some additional
lock cleanup is performed along the way.
A list of the smaller changes:
- newbus methods should be executed with Giant already held, just assert
this
- kbd methods called in the non-polling context should be executed with
Giant already held, just assert this
- Giant is recursive, so we should just take it where we must have it,
without redundant checks if we already have it
- thanks to recent syscons changes we don't need to go through the hoops
to detect if kernel is going to poll us; polling mode is now clearly
separated from non-polling mode
- at present the polling mode can be entered by only one thread
- document special cases in greater detail
Please note that the ukbd code and underlying USB code still lve
dangerously in the kdb context by trying to obtain various locks
including the Giant. If any of those locks are already held by the
stopped threads, then the things would blow up.
Another limitation of the ukbd driver is that it is detached before a
system enters the halt state.
With this commit we can enable kern.stop_scheduler_on_panic by default,
that should not introduce any regressions.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424, r228760
When SCHEDULER_STOPPED() is true the mtx_owned() call may return
an unexpected and thus meaningless result.
So, in the code paths that can be reached when SCHEDULER_STOPPED() is true
we need to protect the mtx_owned() calls with the SCHEDULER_STOPPED()
checks and ensure that an appropriate branch is taken in each case.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424
At the moment grab and ungrab methods of all console drivers are no-ops.
Current intended meaning of the calls is that the kernel takes control of
console input. In the future the semantics may be extended to mean that
the calling thread takes full ownership of the console (e.g. console
output from other threads could be suspended).
Inspired by: bde
MFC after: 2 months
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
It appears this device fails if sent a SYNCHRONIZE_CACHE command, so add
quirk to avoid sending it.
I will follow up with Micron on this issue, and will adjust the quirk if
necessary based on their feedback.
Reviewed by: hselasky@
transfer statemachine. This work is about using a single
state variable instead of multiple state bits as input
for the USB statemachine to determine what to do in the
various parts of the code. No APIs towards USB device
drivers or USB host controller drivers will be changed.
MFC after: 1 month
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
to the kernel's pause() function. The pause() function can now be used
when cold != 0. Also assert that the timeout in system ticks must be
positive.
Suggested by: Bruce Evans
MFC after: 1 week
to kern/subr_bus.c. Simplify this function so that it no longer
depends on malloc() to execute. Identify a few other places where
it makes sense to use device_delete_all_children().
MFC after: 1 week
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
controller.
AX88772B data sheet does not show detailed information about
checksum offloading related things. It seems the controller has
lots of options to support checksum offloading but I failed to
understand why this feature requires so much complex controller
configuration and status bits.
One of major difference between AX88772B and its predecessor is
AX88772B uses a new RX header format when RX checksum offloading is
enabled. It also requires the received length of a frame should be
multiple of 4. Controller will pad necessary bytes to make the
length of received frame to be multiple of 4. It is driver's
responsibility to offset this pad bytes.
Note, AX88772B could be configured to get partial checksum value in
in RX header. This mode uses different RX header format and
currently we don't use that fature.
This change makes axe(4) use driver specific MII attach handler to
override uether(9)'s default MII attach and announce flow-control
capability for AX88178/AX88772A/AX88772B to PHY drivers. It seems
original AX88772 also supports flow-control but I didn't enable it
due to lack of test/access to the controller. The flow-control
threshold parameter is loaded from EEPROM and there is no way to
override this value without reprogramming EEPROM. For AX88772B,
TX/RX IP/TCP/UDP checksum offloading is announced to network stack.
IPv6 and PPPoE checksum offloading is also supported by controller
but we have no way to take advantage of these features.
Driver already knows PHY address so make PHY driver know that
information and remove unnecessary PHY address check used in
miibus_readreg/miibus_writereg callbacks. Also announce AX88178,
AX88772A and AX88772B support VLAN over-sized frame.
While I'm here clean up headers and remove axe_start() in
axe_init() because the link wouldn't be available right after media
change.
handler such that driver can announce interface capabilities and
can do its own MII attach. Currently all USB ethernet controllers
have no way to establish a link with pause capabilities. Lack of
checksum offloading support also was one of reason to bring this
change in.
This change adds a couple of wrappers to USB ethernet drivers
(uether_ifmedia_upd, uether_init and uether_start). All exported
functions in uether has prefix uether_ so I think it's more
consistent to have wrappers that follow the convention.
This change preserves ABI/KPI so it should be safe to merge this
change to stable/8.
While I'm here add missing __FBSDID and clean up headers.
Reviewed by: hselasky
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
on the largest multi-write size.
From the submitter:
==
I looked further into the magic 88-byte threshold after which the bug
occurs. It turns out that figure included the 24-byte tx_desc, and up
to 64 bytes of beacon frame (header+data).
rum_write_multi doesn't seem happy with writing >64 bytes at a time to
the MAC register. If I break it up into separate calls (e.g. bytes
0-63, then bytes 64-65, written at the appropriate offset) I see the
proper beacon frames being transmitted now.
==
Submitted by: Steven Chamberlain <steven@pyro.eu.org>
MFC after: 3 days
Check for this case and just return, so that the UCOM unit number zero is
not accidentially freed.
Submitted by: Danish FreeBSD user at EuroBSDcon 2011
MFC after: 3 days
drivers that only ever attach to a particular MAC driver, i.e. inphy(4),
ruephy(4) and xlphy(4), to the directory where the respective MAC driver
lives and only compile it into the kernel when the latter is also there,
also removing it from miibus.ko and moving it into the module of the
respective MAC driver.
- While at it, rename exphy.c, which comes from NetBSD where the MAC driver
it corresponds to also is named ex(4) instead of xl(4) but that in FreeBSD
actually identifies itself as xlphy(4), and its function names accordingly
for consistency.
- Additionally while at it, fix some minor style issues like whitespace
in the register headers and add multi-inclusion protection to inphyreg.h.
CAM.
Desriptor sense is a new sense data format that originated in SPC-3. Among
other things, it allows for an 8-byte info field, which is necessary to
pass back block numbers larger than 4 bytes.
This change adds a number of new functions to scsi_all.c (and therefore
libcam) that abstract out most access to sense data.
This includes a bump of CAM_VERSION, because the CCB ABI has changed.
Userland programs that use the CAM pass(4) driver will need to be
recompiled.
camcontrol.c: Change uses of scsi_extract_sense() to use
scsi_extract_sense_len().
Use scsi_get_sks() instead of accessing sense key specific
data directly.
scsi_modes: Update the control mode page to the latest version (SPC-4).
scsi_cmds.c,
scsi_target.c: Change references to struct scsi_sense_data to struct
scsi_sense_data_fixed. This should be changed to allow the
user to specify fixed or descriptor sense, and then use
scsi_set_sense_data() to build the sense data.
ps3cdrom.c: Use scsi_set_sense_data() instead of setting sense data
manually.
cam_periph.c: Use scsi_extract_sense_len() instead of using
scsi_extract_sense() or accessing sense data directly.
cam_ccb.h: Bump the CAM_VERSION from 0x15 to 0x16. The change of
struct scsi_sense_data from 32 to 252 bytes changes the
size of struct ccb_scsiio, but not the size of union ccb.
So the version must be bumped to prevent structure
mis-matches.
scsi_all.h: Lots of updated SCSI sense data and other structures.
Add function prototypes for the new sense data functions.
Take out the inline implementation of scsi_extract_sense().
It is now too large to put in a header file.
Add macros to calculate whether fields are present and
filled in fixed and descriptor sense data
scsi_all.c: In scsi_op_desc(), allow the user to pass in NULL inquiry
data, and we'll assume a direct access device in that case.
Changed the SCSI RESERVED sense key name and description
to COMPLETED, as it is now defined in the spec.
Change the error recovery action for a number of read errors
to prevent lots of retries when the drive has said that the
block isn't accessible. This speeds up reconstruction of
the block by any RAID software running on top of the drive
(e.g. ZFS).
In scsi_sense_desc(), allow for invalid sense key numbers.
This allows calling this routine without checking the input
values first.
Change scsi_error_action() to use scsi_extract_sense_len(),
and handle things when invalid asc/ascq values are
encountered.
Add a new routine, scsi_desc_iterate(), that will call the
supplied function for every descriptor in descriptor format
sense data.
Add scsi_set_sense_data(), and scsi_set_sense_data_va(),
which build descriptor and fixed format sense data. They
currently default to fixed format sense data.
Add a number of scsi_get_*() functions, which get different
types of sense data fields from either fixed or descriptor
format sense data, if the data is present.
Add a number of scsi_*_sbuf() functions, which print
formatted versions of various sense data fields. These
functions work for either fixed or descriptor sense.
Add a number of scsi_sense_*_sbuf() functions, which have a
standard calling interface and print the indicated field.
These functions take descriptors only.
Add scsi_sense_desc_sbuf(), which will print a formatted
version of the given sense descriptor.
Pull out a majority of the scsi_sense_sbuf() function and
put it into scsi_sense_only_sbuf(). This allows callers
that don't use struct ccb_scsiio to easily utilize the
printing routines. Revamp that function to handle
descriptor sense and use the new sense fetching and
printing routines.
Move scsi_extract_sense() into scsi_all.c, and implement it
in terms of the new function, scsi_extract_sense_len().
The _len() version takes a length (which should be the
sense length - residual) and can indicate which fields are
present and valid in the sense data.
Add a couple of new scsi_get_*() routines to get the sense
key, asc, and ascq only.
mly.c: Rename struct scsi_sense_data to struct
scsi_sense_data_fixed.
sbp_targ.c: Use the new sense fetching routines to get sense data
instead of accessing it directly.
sbp.c: Change the firewire/SCSI sense data transformation code to
use struct scsi_sense_data_fixed instead of struct
scsi_sense_data. This should be changed later to use
scsi_set_sense_data().
ciss.c: Calculate the sense residual properly. Use
scsi_get_sense_key() to fetch the sense key.
mps_sas.c,
mpt_cam.c: Set the sense residual properly.
iir.c: Use scsi_set_sense_data() instead of building sense data by
hand.
iscsi_subr.c: Use scsi_extract_sense_len() instead of grabbing sense data
directly.
umass.c: Use scsi_set_sense_data() to build sense data.
Grab the sense key using scsi_get_sense_key().
Calculate the sense residual properly.
isp_freebsd.h: Use scsi_get_*() routines to grab asc, ascq, and sense key
values.
Calculate and set the sense residual.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
Import the rest of HID improvements from the branch:
- improve report descriptor parser in libusbhid to handle several kinds of
reports same time;
- add to the libusbhid API two functions wrapping respective kernel IOCTLs
for reading and writing reports;
- tune uhid IOCTL interface to allow reading and writing arbitrary report,
when multiple supported by the device;
- teach usbhidctl to set output and feature reports;
- make usbhidaction support all the same item names as bhidctl.
Sponsored by: iXsystems, inc.
This change fixes a race in device side mode during clear-stall from
host, which can cause data to be sent too early on the given
endpoint.
Approved by: re (kib)
MFC after: 1 week
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
We are allocating some kilobytes of extra memory during USB device enumeration.
This does not change alot under FreeBSD, but makes sense for various embedded
operating systems using the FreeBSD USB stack, which have less memory
resources available.
Approved by: re (kib)
MFC after: 1 week
is retrieved after a failed SCSI command to continue normal
operation. Else this sense information is retrived at the next
SCSI command.
Approved by: re (kib)
Reported by: Alex Kozlov
MFC after: 1 week
PR: usb/160299
which does not support the no synchronize cache SCSI command.
The __FreeBSD_version version macro has been bumped and
external kernel modules needs to be recompiled after
this patch.
Approved by: re (kib)
MFC after: 1 week
PR: usb/160299
device having the same name like a previous one is not created before the old
one is gone. This fixes some panics due to asserts in the devfs code which
were added recently.
Approved by: re (kib)
MFC after: 1 week
ID. This fixes USB_SET_IMMED call (synchronous operation) of the uhid(4)
driver on devices with single report ID.
Reviewed by: hselasky
Approved by: re (kib)
MFC after: 1 week
coordinates, such as digitizers and touch-screens, leaving these devices
to uhid(4) and user-level. Specially patched xf86-input-mouse driver can
handle them, that isn't done and can't be done properly with ums(4)
because of mouse(4) protocol limitations.
Approved by: re (kib)
Back in 2009 I changed the ABI of the GIO_KEYMAP and PIO_KEYMAP ioctls
to support wide characters. I created a patch to add ABI compatibility
for the old calls, but I didn't get any feedback to that.
It seems now people are upgrading from 8 to 9 they experience this
issue, so add it anyway.
supports IPv4/IPv6 checksum offloading and VLAN tag insertion/
stripping as well as WOL. Because uether does not provide a way
to announce driver specific offload capabilities to upper stack,
checksum offloading support needs more work and will be done in
future.
Special thanks to ASIX for donating sample hardware.
H/W donated by: ASIX Electronics
Reviewed by: hselasky
system timer is stopped during shutdown and that the pause() statement in ukbd
causes infinite hang in this regard. The fix is to use mi_switch() instead of
pause() to do the required task switch to ensure that the required USB processes
get executed.
Reported by: Mike_Karels@mcafee.com
MFC after: 1 week
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
latter.
It appears that the addition to uath(4) came in through PR kern/135009,
which had tested another device, the SMCWUSBTG2, successfully with uath(4)
and included the SMCWUSBG as it "has the same chipset". I can find no
other evidence that these two do actually share the same chipset. Moreover,
Linux treats the SMCWUSBG as a zyd(4) device also.
This reverts r223537.
Discussed with: hselasky, kevlo
MFC after: 1 week
dynamically loaded device drivers get a chance to run their event hooks.
- Decouple the USB suspend and resume lock from witness. It produces some
false warnings due to reusing the lock name among multiple devices.
MFC after: 3 days
is now required by bus_autoconf.
- Allow interface class matching even if device class is vendor specific.
- Update bus_autoconf tool to not generate system and subsystem match lines
for the nomatch event.
PR: misc/157903
MFC after: 14 days
sorted according to the mode which they support:
host, device or dual mode
- Add generic tool to extract these data:
tools/bus_autoconf
Discussed with: imp
Suggested by: Robert Millan <rmh@debian.org>
PR: misc/157903
MFC after: 14 days
High-speed USB HUB by resetting the transaction translator (TT)
before trying re-enumeration. Also when clear-stall fails multiple times
try a re-enumeration.
Suggested by: Trevor Blackwell
MFC after: 14 days
This brings USB bus more in line with how newbus is supposed to be used.
Also, because of the two-pass probing the following message was produced
by devd in default configuration when almost any USB device was
connected:
Unknown USB device: vendor <> product <> bus <>
This should be fixed now.
Note that many USB device drivers pass some information from probe
method to attach method via ivars. For this to continue working we rely
on the fact that the subr_bus code calls probe method of a winning driver
again before calling its attach method in the case where multiple
drivers claim to support a device. This is done because device
description is set in successful probe methods and we want to get a correct
device description from a winning driver. So now this logic is re-used
for setting ivars too.
Reviewed by: hselasky
MFC after: 1 month
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
will generate a short terminated USB transfer if
the maximum NCM frame size is greater than what
the driver can handle.
Reported by: Matthias Benesch
MFC after: 7 days
Approved by: thompsa (mentor)
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
SCSI status errors to CAM (that was wrong, as it too often turned retriable
wire errors into non-retriable REQUEST SENSE errors), do it only for STALL
errors on control pipe of the CBI devices. STALL on control pipe is just
a one of the ways to report error for CBI devices.
PR: usb/150401, usb/154593.
Reviewed by: hselasky
MFC after: 1 week
- Add more fields for USB device and host mode
- Add more information to USB PF header so that decoding
can easily be done by software analyzer tools like
Wireshark.
- Optimise usbdump to display USB streams in text format
more efficiently.
- Software using USB PF must be recompiled after
this commit, due to structure changes.
MFC after: 7 days
Approved by: thompsa (mentor)
report descriptor information, sysctl utility
will show it for us.
- Modify sysctl node description to make it more
understanable.
Found by: Alexander Best <arundel@freebsd.org>
Submitted by: Eygene Ryabinkin <rea@freebsd.org>
MFC after: 14 days
Approved by: thompsa (mentor)
value is updated after that we read it in the queue-head. This patch can
fix problems with BULK timeouts. The issue was found on a Nvidia chipset.
MFC after: 14 days
Approved by: thompsa (mentor)
means of allowing vendor specific interface class for audio and MIDI devices.
- Add new quirks for this. The vendor and product list in OpenBSD's
dev/usb/umidi_quirks.c was used as reference.
MFC after: 14 days
Approved by: thompsa (mentor)
While updating Tx stats, already freed node could be referred and cause
page fault. To avoid such panic, spool Tx stats in driver's softc. Then,
on every ratectl interval, grab node though ieee80211_iterate_nodes() and
update ratectl stats.
* Simplify some code in run_iter_func().
* Fix typo
* Use memset instead of bzero (hselasky @)
PR: kern/153938
Submitted by: PseudoCylon <moonlightakkiy@yahoo.ca>
Approved by: thompsa (mentor)
Drivers which rely on net80211 to create the beacon need to call
ieee80211_beacon_update() on iv_update_beacon() calls. This is required
that certain bits, e.g. TIM, get updated. A call to ieee80211_beacon_alloc()
is not enough because it does not care about flags which can only change
during runtime. By design a beacon is supposed to be allocated only once
while moving into RUN state.
To handle all possible calls to iv_update_beacon() the run_updateslot()
function has been revived and run_updateprot() has been added.
run_updateslot() handles slot time changes and run_updateprot() changes
to protection, both can change while nodes associate/leave.
Submitted by: Alexander Zagrebin <alex at zagrebin.ru>,
PseudoCylon <moonlightakkiy atyahoo.ca>
MFC after: 3 weeks
- use device_printf() instead of printf() to give more accurate warnings.
- use memcpy() instead of bcopy().
- add missing #if's for non-FreeBSD compilation.
Approved by: thompsa (mentor)
error address on a decoding error to unlatch it and to allow
us to print a better diagnostics message. This also has the
side effect of clearing the condition, which prevents an
interrupt storm.
This fixes hostap mode for at least ral(4) and run(4), because there is
no sufficient call into drivers which could be used initialize the node
related ratectl variables.
MFC after: 3 days
all new devices added between our r211022 and their git revision
93ad03d60b5b18897030038234aa2ebae8234748
Also correct a Foxconn entry.
MFC after: 1 week
AX88772 controllers. ASIX added a new feature for AX88178/AX88772
controllers which allows combining multiple TX frames into a single
big frame. This was to overcome one of USB limitation where it
can't generate more than 8k interrupts/sec which in turn means USB
ethernet controllers can not send more than 8k packets per second.
Using ASIX's feature greatly enhanced TX performance(more than 3~4
times) compared to 7.x driver. However it seems r184610 removed
boundary checking for buffered frames which in turn caused
instability issues under certain conditions. In addition, using
ASIX's feature triggered another issue which made USB controller
hang under certain conditions. Restarting ethernet controller
didn't help under this hang condition and unplugging and replugging
the controller was the only solution. I believe there is a silicon
bug in TX frame combining feature on AX88178/AX88772 controllers.
To address these issues, reintroduce the boundary checking for both
AX88178 and AX88772 after copying a frame to USB buffer and do not
use ASIX's multiple frame combining feature. Instead, use USB
controller's multi-frame transmit capability to enhance TX
performance as suggested by Hans[1].
This should fix a long standing axe(4) instability issues reported
on AX88772 and AX88178 controllers. While I'm here remove
unnecessary TX frame length check since upper stack always
guarantee the size of a frame to be less than MCLBYTES.
Special thanks to Derrick Brashear who tried numerous patches
during last 4 months and waited real fix with patience. Without
this enthusiastic support, patience and H/W donation I couldn't fix
it since I was not able to trigger the issue on my box.
Suggested by: hselasky [1]
Tested by: Derrick Brashear (shadow <> gmail dot com>
H/W donated by: Derrick Brashear (shadow <> gmail dot com>
PR: usb/140883
isn't configurable in a meaningful way. This is for ifconfig(8) or
other tools not to change code whenever IFT_USB-like interfaces are
registered at the interface list.
Reviewed by: brooks
No objections: gavin, jkim
or detached. Normally it should be changed through user land ioctl(2)
system calls but it looks there's no apps for USB and no need.
With this patch, libpcap would detect the usbus interfaces correctly and
tcpdump(1) could dump the USB packets into PCAP format with -w option.
However it couldn't print the output to console because there's no
printer-routine at tcpdump(1).
hence existing applications like webcamd are expecting that.
This problem was introduced by SVN change 214221 where cdev=
was replaced by ugen= by accident. Solve this problem by
redefining cdev= in devd notifications.
MFC after 3 days.
Approved by: thompsa (mentor)
(wrong unit number for a host controller) when the module is load /
unloaded repeatly. Attaching the USB pf is moved to usbus device's
attach.
Pointed by: yongari
Shorten the descriptive strings for Huawei devices. The vendor or
operator name should not be included in the device name.
Submitted by: Emile Coetzee
MFC after: 3 days
packets which go through each USB host controllers. Its implementations
are almost based on BPF code and very similar with it except it's
little bit customized for USB packet only. The userland program
usbdump(8) would be committed soon.
Discussed with: hps, thompsa, yongari
K3765 datacard. After ejecting this device, it reappears using
the normal K3765 ID. It does not switch automatically
Reviewed by: n_hibma
Obtained from: OpenBSD
MFC after: 2 weeks
and updated comments in the usb_quirk.h header file.
The main purpose of this is to expose the quirks for ejecting 3G
modules. usb_modeswitch in Linux does a great job of collecting
information on these, and with the quirks module people can try out the
modeswitch config file entries on FreeBSD, hence the SCSI strings in the
man page.
MFC after: 2 weeks
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
based devices (QUALCOMMINC 0x2000). He made it use SCSI eject instead of
ZTE STOR eject. This prevented my ZTE MF626 dongle from switching.
- Apply both eject methods for ZTE STOR based devices. Works on my as
well as mav's device.
- Remove the duplicate.
- Sort the usbdevs entries for Qualcomm so this won't happen again.
- Add bootverbose message displaying the fact that we are ejecting (and
how).
Reviewed by: mav
MFC after: 2 weeks
information through devd. My E220 now produces the notification (1 line):
+u3g0 at bus=1 hubaddr=1 port=0 devaddr=2 interface=0 \
vendor=0x12d1 product=0x1003 devclass=0x00 devsubclass=0x00 \
sernum="" release=0x0000 intclass=0xff intsubclass=0xff \
ttyname=U0 ttyports=2 on uhub0
Note: serial/ufoma and net/uhso still provide port number and tty name
(uhso only) information through sysctls, which should now be removed.
Reviewed by: hpselasky
- Fix the loop count on detach (causing a panic on detaching a serial
dongle).
- Increase a buffer in case some driver want extra long tty device names
(postfixing the purpose of the tty for example, e.g. u3g.ppp).
notification. devd would stop evaluating at 'at' (not '<k>=<v>') and
hence prevent 'port=X' (and 'bus=<"on" string>) from making it into the
environment for the devd action.
Reviewed by: hselasky
MFC after: 2 weeks
- hw.usb.ucom.cons_unit is now split into
hw.usb.ucom.cons_unit/...cons_subunit.
Note: The tunable/sysctl hw.usb.ucom.cons_unit needs to be reviewed if
a) a console was defined a USB serial devices, and a USB device with
more than 1 subunit is present, and this device is attached before the
device functioning as a console
or
b) a console was defined on a USB device with more than 1 subunit
Reviewed by: hps
MFC after: 2 weeks
within the first 4 bytes of the EHCI memory space. For controllers that
use big-endian MMIO, reading them with 1- and 2-byte reads would then
return the wrong values. Instead, read the combined register with a 4-byte
read and mask out the interesting quantities.
important for USB 2.0 devices and some of them reported to have problems
with large transactions. But USB 3.0 benchmarks show that limited number
of transactions per second on USB makes impossible to reach high transfer
speeds without using bigger transactions.
On my tests this change allows to read up to 220MB/s from USB-attached SSD
(at block size of 256-512KB), comparing to only 113MB/s without it.
Reviewed by: hselasky
proper solution which is to not use the TERMINATE pointer, but rather
link to a halted TD. The initial fix was due to a misunderstanding
about how the EHCI hardware works. Thanks to Alan Stern for clearing
this up. This patch can increase mass storage read performance
significantly when the IRQ rate is less than 8000 IRQ/s.
Approved by: thompsa (mentor)
- correct the ethernet payload remainder which
must be post-offseted by -14 bytes instead of
0 bytes. This is not very clearly defined in the
NCM specification.
- add development feature about limiting the
maximum datagram count in each NCM payload.
- zero-pad alignment data
- add TX-interval tuning sysctl
Approved by: thompsa (mentor)
It seems axe(4) controllers support interrupt endpoint such that
enabling interrupt endpoint generates about 1000 interrupts/sec.
Controllers transfer 8 bytes data through interrupt endpoint and
the data include link UP/DOWN state as well as some PHY related
information. Previously axe(4) didn't use the transferred data and
didn't even try to read the data. Because axe(4) counts on mii(4)
to detect link state changes there is no need to use interrupt
endpoint here.
This change fixes generation of unnecessary interrupts which was
seen when interface is brought to UP.
No objections from: hselasky
opposition to the change, since really we need to implement missing
functionality in drivers or the 802.3 layer.
For now, restore a reminder message for a missing rum_update_mcast, but
print it only once.
special eject command to reappear as modem. It also requires DIR_IN flag
in the command message, so we supply some dummy data along with the command.
Feedback from X080S owners appreciated. I have not a pure Alcatel/TCTMobile
device, but another one under "Svyaznoy" (Связной) brand, and I didn't yet
managed to get it working. It is successfully recognized, it responds to
AT commands, but it shuts up right after successfull CONNECT response.
Reviewed by: hps
successfully received a frame but we failed to pass it to upper
stack due to lack of resources. So update if_iqdrops counter
instead of updating if_ierrors counter.
mode in the USB core. The patch mostly consists of updating the USB
HUB code to support USB 3.0 HUBs. This patch also add some more USB
controller methods to support more active-alike USB controllers like
the XHCI which needs to be informed about various device state events.
USB 3.0 HUBs are not tested yet, due to lack of hardware, but are
believed to work.
After this update the initial device descriptor is only read twice
when we know that the bMaxPacketSize is too small for a single packet
transfer of this descriptor.
Approved by: thompsa (mentor)
controllers combine multiple TX requests into single one if there
is room in TX buffer of controller. Updating TX packet counter at
the end of TX completion resulted in incorrect TX packet counter as
axe(4) thought it sent 1 packet. There is no easy way to know how
many combined TX were completed in the callback.
Because this change updates TX packet counter before actual
transmission, it may not be ideal one. But I believe it's better
than showing fake 8kpps under high TX load. With this change, TX
shows 221kpps on Linksus USB200M.
scratch. This driver adds support for USB3.0 devices. The XHCI
interface is also backwards compatible to USB2.0 and USB1.0 and will
evntually replace the OHCI/UHCI and EHCI drivers.
There will be follow-up commits during the coming week to link the
driver into the default kernel build and add missing USB3.0
functionality in the USB core. Currently only the driver files are
committed.
Approved by: thompsa (mentor)
greater than 65535 bytes then the CDC driver might not work as expected, which
is not likely with the existing USB speeds.
Submitted by: Hans Petter Selasky
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
vendor ID in the vendor section, and by symbolic name in the product
section. Products are sorted by product ID. While here, get rid of a
duplicate Microsoft Mouse entry, revealed by sorting.
MFC after: 1 week
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
plug. Note that the Vendor ID 0x04b4 is officially assigned to Cypress,
so use that instead of adding a second vendor with an identical ID, in the
same way other similar cases are treated in usb/usbdevs.
PR: usb/132785
Submitted by: Dirk-Willem van Gulik <dirkx webweaving.org>
MFC after: 1 week
- Fixed the interface probe routine to only attach to USB interfaces the driver
actually supports. This allows other drivers to attach to things like
MicroSD slots etc.
- Fixed network interface enumeration to be globally sequential instead of
relying on the USB interface numbers. This make sure the first network
interface always is at uhso0 and the second at usho1 and so on.
- Added a radio kill switch; exposed through sysctl.
- Updated the manual page to be verbose about the number of serial ports and
include iCON 452 in the set of tested hardware.
Submitted by: Fredrik Lindberg
callback function will be executed, and that the key won't be deleted during
the init process.
- txmic and rxmic are written into the chip the same place regardless of
opmode.
- Make the hardware generate 802.11 sequence numbers.
Submitted by: Akinori Furukoshi
Obtained from: git://gitorious.org/run/run.git
The following systems are involved:
- DB-88F5182
- DB-88F5281
- DB-88F6281
- DB-78100
- SheevaPlug
This overhaul covers the following major changes:
- All integrated peripherals drivers for Marvell ARM SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- Since the common FDT infrastrucutre (fdtbus, simplebus) is used we say
good by to obio / mbus drivers and numerous hard-coded config data.
Note that world needs to be built WITH_FDT for the affected platforms.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation.
via %s
Most of the cases looked harmless, but this is done for the sake of
correctness. In one case it even allowed to drop an intermediate buffer.
Found by: clang
MFC after: 2 week
The driver is stub. It just creates device entry and feeds
reassembled packets from hardware into it.
If in future we would port wsmouse(4) from NetBSD, or make
sysmouse(4) to support absolute motion events, then the driver
can be extended to act as system mouse. Meanwhile, it just
presents a /dev/uep0, that can be utilized by X driver, that
I am going to commit to ports tree soon.
The name for the driver is chosen to be the same as in NetBSD,
however, due to different USB stacks this driver isn't a port.
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
Reported by: Richard Kolkovich
Submitted by: Hans Petter Selasky
