to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
and there are ifnets, that do that via counter(9). Provide a flag that
would skip cache line trashing '+=' operation in ether_input().
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Reviewed by: melifaro, adrian
Approved by: re (marius)
set to 15 to indicate that the peer did not send a window scale option
with its SYN. Do not send a window scale option in the SYN|ACK reply
in that case.
cards.
This is a T4 and T5 chip feature which lets the chip deliver multiple
Ethernet frames in a single buffer. This is more efficient within the
chip, in the driver, and reduces wastage of space in rx buffers.
- Always allocate rx buffers from the jumbop zone, no matter what the
MTU is. Do not use the normal cluster refcounting mechanism.
- Reserve space for an mbuf and a refcount in the cluster itself and let
the chip DMA multiple frames in the rest.
- Use the embedded mbuf for the first frame and allocate mbufs on the
fly for any additional frames delivered in the cluster. Each of these
mbufs has a reference on the underlying cluster.
- tom_uninit had to be reworked not to hold the adapter lock (a mutex)
around t4_deactivate_uld, which acquires the uld_list_lock.
- the ifc_match for the interface cloner that creates the tracer ifnet
had to be reworked as the kernel calls ifc_match with the global
if_cloners_mtx held.
all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and
for general purpose monitoring without tapping any cxgbe or cxl ifnet
directly.
Tracers on the T4/T5 chips provide access to Ethernet frames exactly as
they were received from or transmitted on the wire. On transmit, a
tracer will capture a frame after TSO segmentation, hw VLAN tag
insertion, hw L3 & L4 checksum insertion, etc. It will also capture
frames generated by the TCP offload engine (TOE traffic is normally
invisible to the kernel). On receive, a tracer will capture a frame
before hw VLAN extraction, runt filtering, other badness filtering,
before the steering/drop/L2-rewrite filters or the TOE have had a go at
it, and of course before sw LRO in the driver.
There are 4 tracers on a chip. A tracer can trace only in one direction
(tx or rx). For now cxgbetool will set up tracers to capture the first
128B of every transmitted or received frame on a given port. This is a
small subset of what the hardware can do. A pseudo ifnet with the same
name as the nexus driver (t4nex0 or t5nex0) will be created for tracing.
The data delivered to this ifnet is an additional copy made inside the
chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual.
/* watch cxl0, which is the first port hanging off t5nex0. */
# cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting)
# cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving)
# cxgbetool t5nex0 tracer list
# tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire
If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K
"frames" with no L3/L4 checksum but this will show you the frames that
were actually transmitted.
/* all done */
# cxgbetool t5nex0 tracer 0 disable
# cxgbetool t5nex0 tracer 1 disable
# cxgbetool t5nex0 tracer list
# ifconfig t5nex0 destroy
when the interface is up.
- Add a tunable to control the TOE's rx coalesce feature (enabled by
default as it always has been). Consider the interface MTU or the
coalesce size when deciding which cluster zone to use to fill the
offload rx queue's free list. The tunable is:
dev.{t4nex,t5nex}.<N>.toe.rx_coalesce
MFC after: 1 day
it is being installed). Improve other error messages while here.
- Select special FPGA specific configuration profile when appropriate.
MFC after: 3 days
includes support for the NIC and TOE features of the 40G, 10G, and
1G/100M cards based on the T5.
The ASIC is mostly backward compatible with the Terminator 4 so cxgbe(4)
has been updated instead of writing a brand new driver. T5 cards will
show up as cxl (short for cxlgb) ports attached to the t5nex bus driver.
Sponsored by: Chelsio
the firmware (instead of just the main firmware version) when evaluating
firmware compatibility. Document the new "hw.cxgbe.fw_install" knob
being introduced here.
This should fix kern/173584 too. Setting hw.cxgbe.fw_install=2 will
mostly do what was requested in the PR but it's a bit more intelligent
in that it won't reinstall the same firmware repeatedly if the knob is
left set.
PR: kern/173584
MFC after: 5 days
CSUM_TCP too. They are all set explicitly by the kernel usually.
While here, fix an unrelated bug where hardware L4 checksum calculation
was accidentally disabled for some IPv6 packets.
Reported by: alfred@
MFC after: 3 days
cannot be freed while do_pass_accept_req is running. This closes a race
where do_pass_establish on another CPU (the driver chose a different
queue for the new tid) expands the synq entry into a full PCB and then
releases the only hold on it, all while do_pass_accept_req is still
running.
MFC after: 3 days
This is the Compressed Local IPv6 table on the chip. To save space, the
chip uses an index into this table instead of a full IPv6 address in
some of its hardware data structures.
For now the driver fills this table with all the local IPv6 addresses
that it sees at the time the table is initialized. I'll improve this
later so that the table is updated whenever new IPv6 addresses are
configured or existing ones deleted.
MFC after: 1 week
- Teach find_best_mtu_idx() to deal with IPv6 endpoints.
- Install correct protosw in offloaded TCP/IPv6 sockets when DDP is
enabled.
- Move set_tcp_ddp_ulp_mode to t4_tom.c so that t4_tom.h can be included
without having to drag in t4_msg.h too. This was bothering the iWARP
driver for some reason.
MFC after: 1 week
- Add full support for IPv6 addresses.
- Read the size of the L2 table during attach. Do not assume that PCIe
physical function 4 of the card has all of the table to itself.
- Use FNV instead of Jenkins to hash L3 addresses and drop the private
copy of jhash.h from the driver.
MFC after: 1 week
on the fast data path) and use them instead of frobbing the adapter lock
and busy flag directly.
Other changes made while reworking all slow operations:
- Wait for the reply to a filter request (add/delete). This guarantees
that the operation is complete by the time the ioctl returns.
- Tidy up the tid_info structure.
- Do not allow the tx queue size to be set to something that's not a
power of 2.
MFC after: 1 week
resources are partitioned.
- Reduce the number of virtual interfaces reserved for PF4. This leaves
spare room in the source MAC table and allows the driver to setup
filters that rewrite the source MAC address.
- Reduce the number of filters and use the freed up space for the CLIP
(Compressed Local IPv6 addresses) table. This is a prerequisite for
IPv6 TOE support which will follow separately in a series of commits.
MFC after: 1 week
embryonic connection has been setup and never attempt to abort a tid
before this is done. This fixes a bad race where a listening socket is
closed when the driver is in the middle of step (b) here. The symptom
of this were "ARP miss" errors from the driver followed by tid leaks.
A hardware-offloaded passive open works this way:
a) A SYN "hits" the TCAM entry for a server tid and the chip delivers it
to the queue associated with the server tid (say, queue A). It waits
for a response from the driver telling it what to do.
b) The driver decides it is ok to proceed. It adds the new tid to the
list of embryonic connections associated with the server tid and then
hands off the SYN to the kernel's syncache to make sure that the kernel
okays it too. If it does then the driver provides an L2 table entry,
queue id (say, queue B), etc. and instructs the chip to send the SYN/ACK
response.
c) The chip delivers a status to queue B depending on how the third step
of the 3-way handshake goes. The driver removes the tid from its list
of embryonic connections and either expands the syncache entry or
destroys the tid. In any case all subsequent messages for the new tid
will be delivered to queue B, not queue A. Anything running in queue B
knows that the L2 entry has long been setup and the new flag is of no
interest from here on. If the listener is closed it will deal with
so_comp as normal.
MFC after: 1 week
counter) when the syncache doesn't want the driver to reply to an
incoming SYN. This fixes a harmless bug where tids_in_use would
go out of sync with the hardware counter.
MFC after: 3 days
