- Fix speaker issues with Dell Vostro 1500 (GPIO0)
Tested by: John Wright <jwright.gmail.com>
- Apply ridiculous quirk on Asus A8X series (A8JC, A8M, A8xx, etc). These
different laptop series share simmilar pci id, hardware codecs, etc.
but works differently. A slight difference in connection type for
widget #26 is used to differentiate it.
Tested by: eric baumbach <embaumbach.gmail.com>
- Apply GPIO0 quirk for ASUS G2K laptop
- Sort ASUS ids accordingly.
Submitted by: jkim
MFC after: 3 days
TX traffic to sit in the send chain until a received packet kick
started the interrupt handler. This would cause extremely slow
performance when used with NFS over UDP.
- Removed untested polling code.
- Updated copyright year in the file header.
- Removed inadvertent ^M's created by DOS text editor.
MFC after: 2 weeks
be handled by chn_abort() and chn_start() alone. This should fix
few issues with single duplex hardware (mostly) or pre virtual record
(RELENG 6) under WINE emulation and possibly others that using
SNDCTL_DSP_SETTRIGGER.
MFC after: 3 days
The problem is that the PM support is part of a much larger WIP here, but due to popular demand I decided to get some of it imported.
Also I forgot the mention:
HW sponsored by: Vitsch Electronics / VEHosting
I've taken a slightly different approach than is used with the ICH8 controllers
in that each controller is not identified individually (eg USB A, USB B, etc).
Instead I've given then same description to each one even though the device ID
differs. This can easily be changed if desired, or ICH8 (and any others using
that approach) can be made to work as this does.
Support is working on the Silicon Image SiI3124/3132.
Support is working on some AHCI chips but far from all.
Remember this is WIP, so test reports and (constructive) suggestions are welcome!
commands can be written to /dev/psm%d and status can be read back from it.
- Reflect the change in psm(4) and bump version for ports.
MFC after: 1 week
Because of this we were not getting further interrupts for link state
changes, thus never went into iface UP state and thus could not transmit.
The only way out of this was an incoming packet generating an rx interrupt
and making us call into bge_link_upd.
Up to rev. 1.101, in bge_start_locked, we only returned instantly
if there was 'no link AND nothing queued for tx'. So with a packet queued
for tx, we hit the register scrubbing at the end of bge_start_locked
and were out fine. We simply lost a packet or two but got the interrupts
need to get into UP state.
With rev. 1.102 this was turned into 'if there is no link OR there is
nothing to send' (correct behaviour) and as long as there is no link
we never hit the register scrubbing and consequently never got the link UP.
What we do now is force an interrupt at the end of bge_ifmedia_upd_locked
so we will call bge_link_upd, clear the link state attention and get
further interrupts.
This helps to get the iface UP on an idle network or at least to get
it UP faster not depending on an rx intr anymore.
In case you could not get a DHCP lease or it took very long,
it was because of this.
It is unknown which chips are affected by this. ASIC rev. 0x2003 was the
most popular trouble candidate.
At least the fiber cards should have been working fine.
Which register to scrub is currently under discussion. The comitted
solution was tested and found to work for a lot of setups. It might
not help with MSI.
The reason why we end up in such a situation is entirely unknown.
PR: kern/111804
Tested by: phk, scottl at Y!
MFC after: 14 days
part of detecting the media. Explicitly ensure that we don't send it to
bpf(4) as bpf(4) isn't setup yet. This worked by accident before the bpf
interface stuff was reworked to avoid other races (bpf_peers_present, etc.)
but now it needs an explicit check to avoid a panic.
MFC after: 3 days
PR: kern/120915
and the igb driver static in the kernel. But it also reflects
some other bug fixes in my development stream at Intel.
PR 122373 is also fixed in this code.
to trip a bug causing the latter to return a zeroed struct
aac_adapter_info. This causes two issues. One is cosmetic only --
a verbose boot prints information about the controller, and shows all
zero:
aac0: Unknown processor 0MHz, 0MB memory (0MB cache, 0MB execution),
unknown battery platform
The second problem is that the firmware version information is stored
away for aac_rev_check, for userland tools (like aaccli) to query via
the FSACTL_MINIPORT_REV_CHECK and FSACTL_LNX_MINIPORT_REV_CHECK ioctls.
When aaccli encounters this issue it prints
Command Error: <The current AFAAPI.DLL is too old to work with the
current controller software.>
Move the RequestSupplementAdapterInfo call after RequestAdapterInfo,
which seems to fix both problems.
abstraction as the RAID and CAM modules, making it nearly impossible
for enough initialization to be done in time for the RAID module to
know whether to attach. On top of this, no reset was being done on
the controller on attach, in violation of the spec. Additionally,
the port enable step was being deferred to the end of the attach
process, long after it should have been done to ensure reliable
operation from the controller. Fix all of these with a few hacks
to force the "attach" and "enable" steps of the core module early
on, and ensure that a reset and port enable also happens early on.
In the future, the driver needs to be refactored to eliminate the
core module abstraction, clean up withe reset/enable steps, and
defer event messages until all of the modules are available to
recieve them.
offload bugs by manual padding for short IP/UDP frames. Unfortunately
it seems that these workaround does not work reliably on newer PCIe
variants of RealTek chips.
To workaround the hardware bug, always pad short frames if Tx IP
checksum offload is requested. It seems that the hardware has a
bug in IP checksum offload handling. NetBSD manually pads short
frames only when the length of IP frame is less than 28 bytes but I
chose 60 bytes to safety. Also unconditionally set IP checksum
offload bit in Tx descriptor if any TCP or UDP checksum offload is
requested. This is the same way as Linux does but it's not
mentioned in data sheet.
Obtained from: NetBSD
Tested by: remko, danger
