These firmwares were obtained from the "Chelsio T5/T4 Unified Wire
v2.12.0.3 for Linux" release. Changes since 1.14.4.0 (which is the
firmware in -STABLE branches) are in the "Release Notes" accompanying
the Unified Wire release and are copy-pasted here as well.
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
ETH
- Fixed a link flap issue on T580-CR.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
- Fixed an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host. (DCBX CEE)
- Fixed an issue where apply bit set for APP id was affecting the ETS and PFC
settings.(DCBX IEEE)
- Fixed an issue where app priority values are not handled correctly in fw.
(DCBX IEEE)
- Fixed an issue where enable/disable dcbx can cause crash. (DCBX CEE,DCBX IEEE)
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host.(DCBX CEE)
- Fixed an issue where enable/disable dcbx can cause crash in firmware.(DCBX CEE)
FOiSCSI
- Fixes an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 6 weeks
Relnotes: yes
Sponsored by: Chelsio Communications
This adds support for the NVRAM handling and the basic SPROM
hardware used on siba(4) and bcma(4) devices, including:
* SPROM directly attached to the PCI core, accessible via PCI configuration
space.
* SPROM attached to later ChipCommon cores.
* SPROM variables vended from the parent SoC bus (e.g. via a directly-attached
flash device).
Additional improvements to the NVRAM/SPROM interface will
be required, but this changeset stands alone as working
checkpoint.
Submitted by: Landon Fuller <landonf@landonf.org>
Reviewed by: Michael Zhilin <mizkha@gmail.com> (Broadcom MIPS support)
Differential Revision: https://reviews.freebsd.org/D6196
This is an initial work in progress to use the replacement bhnd
bus code for devices which support it.
* Add manpage updates for bhnd, bhndb, siba
* Add kernel options for bhnd, bhndbus, etc
* Add initial support in if_bwn_pci / if_bwn_mac for using bhnd
as the bus transport for suppoted NICs
* if_bwn_pci will eventually be the PCI bus glue to interface to bwn,
which will use the right backend bus to attach to, versus direct
nexus/bhnd attachments (as found in embedded broadcom devices.)
The PCI glue defaults to probing at a lower level than the bwn glue,
so bwn should still attach as per normal without a boot time tunable set.
It's also not fully fleshed out - the bwn probe/attach code needs to be
broken out into platform and bus specific things (just like ath, ath_pci,
ath_ahb) before we can shift the driver over to using this.
Tested:
* BCM4311, STA mode
* BCM4312, STA mode
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6191
after r298107
Summary of changes:
- Replace all instances of FILES/TESTS with ${PACKAGE}FILES. This ensures that
namespacing is kept with FILES appropriately, and that this shouldn't need
to be repeated if the namespace changes -- only the definition of PACKAGE
needs to be changed
- Allow PACKAGE to be overridden by callers instead of forcing it to always be
`tests`. In the event we get to the point where things can be split up
enough in the base system, it would make more sense to group the tests
with the blocks they're a part of, e.g. byacc with byacc-tests, etc
- Remove PACKAGE definitions where possible, i.e. where FILES wasn't used
previously.
- Remove unnecessary TESTSPACKAGE definitions; this has been elided into
bsd.tests.mk
- Remove unnecessary BINDIRs used previously with ${PACKAGE}FILES;
${PACKAGE}FILESDIR is now automatically defined in bsd.test.mk.
- Fix installation of files under data/ subdirectories in lib/libc/tests/hash
and lib/libc/tests/net/getaddrinfo
- Remove unnecessary .include <bsd.own.mk>s (some opportunistic cleanup)
Document the proposed changes in share/examples/tests/tests/... via examples
so it's clear that ${PACKAGES}FILES is the suggested way forward in terms of
replacing FILES. share/mk/bsd.README didn't seem like the appropriate method
of communicating that info.
MFC after: never probably
X-MFC with: r298107
PR: 209114
Relnotes: yes
Tested with: buildworld, installworld, checkworld; buildworld, packageworld
Sponsored by: EMC / Isilon Storage Division
* Break out the 'g' phy code;
* Break out the debugging bits into a separate source file, since
some debugging prints are done in the phy code;
* Make some more chip methods in if_bwn.c public.
This brings the size of if_bwn.c down to 6,805 lines which is now
approaching managable.
This (and eventually migrating the other PHY code out) is in preparation
for adding the 11n PHY. No, the 11ac PHY (for the BCM4260 softmac part) isn't
yet open source, so we can't grow that. Yet.
This trims ~3,700 lines of code from if_bwn.c, bringing it down to a slightly
less crazy sounding 10,446 lines of code.
It seems that the only way to supply dtb to loader on Zynq-based
SoCs is to manually generate dtb and place it to pre-defined location
on SD card or TFTP server where loader can pick it up. More modern
approach is to add modules/dtb/%soc% module and let installworld
target generate dtb and copy them to /boot/dtb/ where they can be
loaded by ubldr
undefined symbol svr4_delete_socket which was moved from streams to the svr4 module
in r160558 that created a two-way dependency between them.
PR: 208464
Submitted by: Kristoffer Eriksson
Reported by: Kristoffer Eriksson
MFC after: 2 week
This extracts common code from bhndb_pci, bhnd_pcib, and bhnd_pci_hostb into a
simpler shared bhnd_pci base driver, and should enable SoC-side implementation
of bhnd_pcib root complex support.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D5763
Submitted by: Jun Su <junsu microsoft com>
Reviewed by: jhb, kib, sephe
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5910
It allows implementing loadable kernel modules with new actions and
without needing to modify kernel headers and ipfw(8). The module
registers its action handler and keyword string, that will be used
as action name. Using generic syntax user can add rules with this
action. Also ipfw(8) can be easily modified to extend basic syntax
for external actions, that become a part base system.
Sample modules will coming soon.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Make it compile only for i386/amd64 for now as it's been tested there.
It's quite possible it'll show up elsewhere and we can enable it
for other architectures later.
Tested:
* PC Engines APU1C4
Submitted by: Daniel Wyatt <daniel@dewyatt.com>
Reviewed by: adrian, loos
Differential Revision: https://reviews.freebsd.org/D5389
There's some upcoming work to add new chipset support here and I'd
like to only add 802.11n support to one driver, instead of both
urtwn and rtwn.
There's also missing support for things like 802.11n, some powersave
work, bluetooth integration/coexistence, etc, and also newer parts
(like 8192EU, maybe some 11ac parts, not sure yet.)
So, this is hopefully the first step in a longer set of steps to unify
rtwn/urtwn and extend it with more interesting chipset and functionality
support.
Reviewed by: kevlo
is defined explicitly. It's kinda pointless and results in extra step in
boot sequence which is not really needed, i.e.:
md0: Embedded image 1331200 bytes at 0x8038b7b4
Trying to mount root from ufs:/dev/md0 []...
Mounting from ufs:/dev/md0 failed with error 22.
Trying to mount root from ufs:md0.uzip []...
warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
This update brings initial support for Haswell GPUs.
Tested by: Many users of FreeBSD, PC-BSD and HardenedBSD
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5554
improve cancellation robustness.
Introduce a new file operation, fo_aio_queue, which is responsible for
queueing and completing an asynchronous I/O request for a given file.
The AIO subystem now exports library of routines to manipulate AIO
requests as well as the ability to run a handler function in the
"default" pool of AIO daemons to service a request.
A default implementation for file types which do not include an
fo_aio_queue method queues requests to the "default" pool invoking the
fo_read or fo_write methods as before.
The AIO subsystem permits file types to install a private "cancel"
routine when a request is queued to permit safe dequeueing and cleanup
of cancelled requests.
Sockets now use their own pool of AIO daemons and service per-socket
requests in FIFO order. Socket requests will not block indefinitely
permitting timely cancellation of all requests.
Due to the now-tight coupling of the AIO subsystem with file types,
the AIO subsystem is now a standard part of all kernels. The VFS_AIO
kernel option and aio.ko module are gone.
Many file types may block indefinitely in their fo_read or fo_write
callbacks resulting in a hung AIO daemon. This can result in hung
user processes (when processes attempt to cancel all outstanding
requests during exit) or a hung system. To protect against this, AIO
requests are only permitted for known "safe" files by default. AIO
requests for all file types can be enabled by setting the new
vfs.aio.enable_usafe sysctl to a non-zero value. The AIO tests have
been updated to skip operations on unsafe file types if the sysctl is
zero.
Currently, AIO requests on sockets and raw disks are considered safe
and are enabled by default. aio_mlock() is also enabled by default.
Reviewed by: cem, jilles
Discussed with: kib (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D5289
These firmwares were obtained from the beta "Chelsio T5/T4 Unified Wire
v2.12.0.2 for Linux" release. Changes since last release are listed in the
"Release Notes" accompanying the beta release and are copy-pasted here as well.
The plan is to have only GA'd firmwares in any -STABLE FreeBSD branch so I'll
MFC this (after 2 months) only if it ends up in a GA release.
================================================================================
================================================================================
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.28.0
Date : 02/29/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after
reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic
management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
================================================================================
================================================================================
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.28.0
Date : 02/29/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after
reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic
management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 2 months
Sponsored by: Chelsio Communications
-fPIC has no effect on linking although it seems to be ignored by
GNU ld.bfd. However, it causes ld.lld to terminate with an invalid
argument error.
Reviewed by: dchagin, kib
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5444
These are no longer needed after the recent 'beforebuild: depend' changes
and hooking DIRDEPS_BUILD into a subset of FAST_DEPEND which supports
skipping 'make depend'.
Sponsored by: EMC / Isilon Storage Division
Split heartbeat, shutdown and timesync out of utils code
and name them properly.
Submitted by: Jun Su <junsu microsoft com>
Reviewed by: adrian, sephe, Hongjiang Zhang <honzhan microsoft com>
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5216
and geom_uncompress(4):
1. mkuzip(8):
- Proper support for eliminating all-zero blocks when compressing an
image. This feature is already supported by the geom_uzip(4) module
and CLOOP format in general, so it's just a matter of making mkuzip(8)
match. It should be noted, however that this feature while it sounds
great, results in very slight improvement in the overall compression
ratio, since compressing default 16k all-zero block produces only 39
bytes compressed output block, which is 99.8% compression ratio. With
typical average compression ratio of amd64 binaries and data being
around 60-70% the difference between 99.8% and 100.0% is not that
great further diluted by the ratio of number of zero blocks in the
uncompressed image to the overall number of blocks being less than
0.5 (typically). However, this may be important from performance
standpoint, so that kernel are not spinning its wheels decompressing
those empty blocks every time this zero region is read. It could also
be important when you create huge image mostly filled with zero
blocks for testing purposes.
- New feature allowing to de-duplicate output image. It turns out that
if you twist CLOOP format a bit you can do that as well. And unlike
zero-blocks elimination, this gives a noticeable improvement in the
overall compression ratio, reducing output image by something like
3-4% on my test UFS2 3GB image consisting of full FreeBSD base system
plus some of the packages (openjdk, apache etc), about 2.3GB worth of
file data (800+MB compressed). The only caveat is that images created
with this feature "on" would not work on older versions of FeeBSDxi
kernel, hence it's turned off by default.
- provide options to control both features and document them in manual
page.
- merge in all relevant LZMA compression support from the mkulzma(8),
add new option to select between both.
- switch license from ad-hoc beerware into standard 2-clause BSD.
2. geom_uzip(4):
- implement support for de-duplicated images;
- optimize some code paths to handle "all-zero" blocks without reading
any compressed data;
- beef up manual page to explain that geom_uzip(4) is not limited only
to md(4) images. The compressed data can be written to the block
device and accessed directly via magic of GEOM(4) and devfs(4),
including to mount root fs from a compressed drive.
- convert debug log code from being compiled in conditionally into
being present all the time and provide two sysctls to turn it on or
off. Due to intended use of the module, it can be used in
environments where there may not be a luxury to put new kernel with
debug code enabled. Having those options handy allows debug issues
without as much problem by just having access to serial console or
network shell access to a box/appliance. The resulting additional
CPU cycles are just few int comparisons and branches, and those are
minuscule when compared to data decompression which is the main
feature of the module.
- hopefully improve robustness and resiliency of the geom_uzip(4) by
performing some of the data validation / range checking on the TOC
entries and rejecting to attach to an image if those checks fail.
- merge in all relevant LZMA decompression support from the
geom_uncompress(4), enable automatically when appropriate format is
indicated in the header.
- move compilation work into its own worker thread so that it does not
clog g_up. This allows multiple instances work in parallel utilizing
smp cores.
- document new knobs in the manual page.
Reviewed by: adrian
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D5333
- Add URTWN_WITHOUT_UCODE option (will disable any firmware specific code
when set).
- Do not exclude the driver from build when MK_SOURCELESS_UCODE is set
(URTWN_WITHOUT_UCODE will be enforced unconditionally).
- Do not abort initialization when firmware cannot be loaded;
behave like the URTWN_WITHOUT_UCODE option was set.
- Drop some unused variables from urtwn_softc structure.
Tested with RTL8188EU and RTL8188CUS in HOSTAP and STA modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4849
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
The htree dir_index is perhaps one of the most characteristic
features of the linux ext3 implementation. It was removed
in r281670, due to repeated bug reports.
Damjan Jovanic detected and fixed three bugs and did some
stress testing by building Apache OpenOffice on top of it
so it is now in good shape to bring back.
Differential Revision: https://reviews.freebsd.org/D5007
Submitted by: Damjan Jovanovic
Reviewed by: pfg
Tested by: pho
Relnotes: Yes
MFC after: 2 months (only 10.x)
Add support for Huntington MCDI licensing interface to common code.
Ported from Linux net driver IOCTL functions with restructuring for
initial support for V3 licensing API.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4918
Submitted by: Howard Su <howard0su@gmail.com>
Reviewed by: delphij, royger, adrian
Approved by: adrian (mentor)
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D4676
Creating some files together to do the build system changes in one go.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4859
The upcoming GELI support in the loader reuses parts of this code
Some ifdefs are added, and some code is moved outside of existing ifdefs
The HMAC parts of GELI are broken out into their own file, to separate
them from the kernel crypto/openssl dependant parts that are replaced
in the boot code.
Passed the GELI regression suite (tools/regression/geom/eli)
Files=20 Tests=14996
Result: PASS
Reviewed by: pjd, delphij
MFC after: 1 week
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D4699
rtwnfw got added in r293009 and depends on source-less and
non-free microcode in sys/contrib/dev/rtwn.
PR: 205874
Submitted by: Fabian Keil
Obtained from: ElectroBSD
cperciva's libmd implementation is 5-30% faster
The same was done for SHA256 previously in r263218
cperciva's implementation was lacking SHA-384 which I implemented, validated against OpenSSL and the NIST documentation
Extend sbin/md5 to create sha384(1)
Chase dependancies on sys/crypto/sha2/sha2.{c,h} and replace them with sha512{c.c,.h}
Reviewed by: cperciva, des, delphij
Approved by: secteam, bapt (mentor)
MFC after: 2 weeks
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D3929
The licence grant says something exactly the same as the atheros patent
grant, which is "As long as you use this firmware on our chips, everything
is totally okay." Now, I'm pretty sure if that we /have/ to have this,
we're going to have to have it for every other firmware for every other
device in the tree.
So, I'll flip this off in -HEAD for now so people stop asking about
why rsu/urtwn don't work out of the box, and I'll kick off a larger
discussion about this in the new year.
cards supported by cxgbe(4).
On the host side this driver interfaces with the storage stack via the
ICL (iSCSI Common Layer) in the kernel. On the wire the traffic is
standard iSCSI (SCSI over TCP as per RFC 3720/7143 etc.) that
interoperates with all other standards compliant implementations. The
driver is layered on top of the TOE driver (t4_tom) and promotes
connections being handled by t4_tom to iSCSI ULP (Upper Layer Protocol)
mode. Hardware assistance in this mode includes:
- Full TCP processing.
- iSCSI PDU identification and recovery within the TCP stream.
- Header and/or data digest insertion (tx) and verification (rx).
- Zero copy (both tx and rx).
Man page will follow in a separate commit in a couple of weeks.
Relnotes: Yes
Sponsored by: Chelsio Communications
The mdio driver interface is generally useful for devices that require
MDIO without the full MII bus interface. This lifts the driver/interface
out of etherswitch(4), and adds a mdio(4) man page.
Submitted by: Landon Fuller <landon@landonf.org>
Differential Revision: https://reviews.freebsd.org/D4606
Add support for two new devices: X552 SFP+ 10 GbE, and the single port
version of X550T.
Submitted by: erj
Reviewed by: gnn
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D4186
to do is to clean up the timer handling using the async-drain.
Other optimizations may be coming to go with this. Whats here
will allow differnet tcp implementations (one included).
Reviewed by: jtl, hiren, transports
Sponsored by: Netflix Inc.
Differential Revision: D4055
include the following list of changes:
- Added eswitch ACL table management
Introduce API for managing ACL table.
This API include the following features:
1) vlan filter - for VST/VGT+ support.
2) spoofcheck.
3) robust functionality to allow/drop general untagged/tagged traffic.
4) support for both ingress and egress ACL types.
- Added loopback filter to the vacl table.
- Added multicast list set in the vPort context
- Added promiscuous mode set in the vPort context
- Set the vlan list in vPort context
1) Check caps if VLAN list is not longer than FW supports
2) Set MODIFY_NIC_VPORT_CONTEXT command
- Changed MLX5_EEPROM_MAX_BYTES from 48 to 32 so that a single EEPROM
reading cannot cross the 128-byte boundary. Previously reading the
MCIA register was done in batches of 48 bytes. The third reading
would then by-pass the 127th byte, which means that part of the low
page and part of the high page would be read at the same time, which
created a bug:
1st: 0-47 bytes
2nd: 48-95 bytes
3rd: 96-143 bytes
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4411
driver. This includes binding all interrupt and worker threads
according to the RSS configuration, setting up correct Toeplitz
hashing keys as given by RSS and setting the correct mbuf
hashtype for all received traffic.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4410
vtophys() when loading mbufs for transmission and reception. While at
it all pointer arithmetic and cast qualifier issues were fixed, mostly
related to transmission and reception.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Differential Revision: https://reviews.freebsd.org/D4284
IPv4/IPv6 checksum offloading and VLAN tag insertion/stripping.
Since uether doesn't provide a way to announce driver specific offload
capabilities to upper stack, checksum offloading support needs more work
and will be done in the future.
Special thanks to Hayes Wang from RealTek who gave input.
Use hhook(9) framework to achieve ability of loading and unloading
if_enc(4) kernel module. INET and INET6 code on initialization registers
two helper hooks points in the kernel. if_enc(4) module uses these helper
hook points and registers its hooks. IPSEC code uses these hhook points
to call helper hooks implemented in if_enc(4).
This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really interesting.
Initiator mode tested with Qlogic 1080 adapter is still working fine.
default and add a manual page for mlx5en. The mlx5 module contains
shared code for both infiniband and ethernet. The mlx5en module
contains specific code for ethernet functionality only. A mlx5ib
module is in the works for infiniband support.
Supported hardware:
- ConnectX-4: 10/20/25/40/50/56/100Gb/s speeds.
- ConnectX-4 LX: 10/25/40/50Gb/s speeds (low power consumption)
Refer to the mlx5en(4) manual page for a comprehensive list.
The team porting the mlx5 driver(s) to FreeBSD:
- Hans Petter Selasky <hselasky@freebsd.org>
- Oded Shanoon <odeds@mellanox.com>
- Meny Yossefi <menyy@mellanox.com>
- Shany Michaely <shanim@mellanox.com>
- Shahar Klein <shahark@mellanox.com>
- Daria Genzel <dariaz@mellanox.com>
- Mark Bloch <markb@mellanox.com>
Differential Revision: https://reviews.freebsd.org/D4163
Submitted by: Mark Block <markb@mellanox.com>
Sponsored by: Mellanox Technologies
Reviewed by: gnn @
MFC after: 3 days
work with the upcoming async-drain functionality. Tests can be added
to the tests directory and then the framework can be used to launch
those tests.
MFC after: 1 month
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D1755
from Mellanox Technologies. The current driver supports ethernet
speeds up to and including 100 GBit/s. Infiniband support will be
done later.
The code added is not compiled by default, which will be done by a
separate commit.
Sponsored by: Mellanox Technologies
MFC after: 2 weeks
- Move all files related to the LinuxKPI into sys/compat/linuxkpi and
its subfolders.
- Update sys/conf/files and some Makefiles to use new file locations.
- Added description of COMPAT_LINUXKPI to sys/conf/NOTES which in turn
adds the LinuxKPI to all LINT builds.
- The LinuxKPI can be added to the kernel by setting the
COMPAT_LINUXKPI option. The OFED kernel option no longer builds the
LinuxKPI into the kernel. This was done to keep the build rules for
the LinuxKPI in sys/conf/files simple.
- Extend the LinuxKPI module to include support for USB by moving the
Linux USB compat from usb.ko to linuxkpi.ko.
- Bump the FreeBSD_version.
- A universe kernel build has been done.
Reviewed by: np @ (cxgb and cxgbe related changes only)
Sponsored by: Mellanox Technologies
These are not target-specific modules, so the logic to build them should
be common. This also enables them for arm64.
Sponsored by: The FreeBSD Foundation
linux_syscallnames[] from linux_* to linux32_* to avoid conflicts with
linux64.ko. While here, add support for linux64 binaries to systrace.
- Update NOPROTO entries in amd64/linux/syscalls.master to match the
main table to fix systrace build.
- Add a special case for union l_semun arguments to the systrace
generation.
- The systrace_linux32 module now only builds the systrace_linux32.ko.
module on amd64.
- Add a new systrace_linux module that builds on both i386 and amd64.
For i386 it builds the existing systrace_linux.ko. For amd64 it
builds a systrace_linux.ko for 64-bit binaries.
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D3954
It turns out that it is pretty easy to make CloudABI work on ARM64. We
essentially only need to copy over the sysvec from AMD64 and ensure that
we use ARM64 specific registers.
As there is an overlap between function argument and return registers,
we do need to extend cloudabi64_schedtail() to only set its values if
we're actually forking. Not when we're creating a new thread.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3917
In order to make it easier to support CloudABI on ARM64, move out all of
the bits from the AMD64 cloudabi_sysvec.c into a new file
cloudabi_module.c that would otherwise remain identical. This reduces
the AMD64 specific code to just ~160 lines.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3974
MACHINE_CPUARCH expands to aarch64 for arm64, whereas MACHINE always
corresponds to the directory name under sys/ that contains the sources
for that architecture.
Atheros.
Thanks to OpenBSD for providing a driver based on the original
Atheros open source driver circa 2008. This uses the early, pre-carl9170
atheros provided firmware.
It only supports 11bg at the moment. I've not tested it with 11a
(and so the TX rate control logic may be slightly wrong!) so if
you do have the dual-band version of this hardware please do let me know.
Tested:
* AR9170, TP-Link WN821N 2GHz.
TODO:
* Hook this up to a non-module build.
CTL HA functionality was originally implemented by Copan many years ago,
but large part of the sources was never published. This change includes
clean room implementation of the missing code and fixes for many bugs.
This code supports dual-node HA with ALUA in four modes:
- Active/Unavailable without interlink between nodes;
- Active/Standby with second node handling only basic LUN discovery and
reservation, synchronizing with the first node through the interlink;
- Active/Active with both nodes processing commands and accessing the
backing storage, synchronizing with the first node through the interlink;
- Active/Active with second node working as proxy, transfering all
commands to the first node for execution through the interlink.
Unlike original Copan's implementation, depending on specific hardware,
this code uses simple custom TCP-based protocol for interlink. It has
no authentication, so it should never be enabled on public interfaces.
The code may still need some polishing, but generally it is functional.
Relnotes: yes
Sponsored by: iXsystems, Inc.
only gpiobus configured via FDT is supported. Bus enumeration is
supported. Devices are created for each device found. 1-Wire
temperature controllers are supported, but other drivers could be
written. Temperatures are polled and reported via a sysctl. Errors
are reported via sysctl counters. Mis-wired bus detection is included
for more trouble shooting. See ow(4), owc(4) and ow_temp(4) for
details of what's supported and known issues.
This has been tested on Raspberry Pi-B, Pi2 and Beagle Bone Black
with up to 7 devices.
Differential Revision: https://reviews.freebsd.org/D2956
Relnotes: yes
MFC after: 2 weeks
Reviewed by: loos@ (with many insightful comments)
I/OAT is also referred to as Crystal Beach DMA and is a Platform Storage
Extension (PSE) on some Intel server platforms.
This driver currently supports DMA descriptors only and is part of a
larger effort to upstream an interconnect between multiple systems using
the Non-Transparent Bridge (NTB) PSE.
For now, this driver is only built on AMD64 platforms. It may be ported
to work on i386 later, if that is desired. The hardware is exclusive to
x86.
Further documentation on ioat(4), including API documentation and usage,
can be found in the new manual page.
Bring in a test tool, ioatcontrol(8), in tools/tools/ioat. The test
tool is not hooked up to the build and is not intended for end users.
Submitted by: jimharris, Carl Delsey <carl.r.delsey@intel.com>
Reviewed by: jimharris (reviewed my changes)
Approved by: markj (mentor)
Relnotes: yes
Sponsored by: Intel
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3456
This driver allows read the software reset switch state and control the
status LEDs.
The GPIO pins have their direction (input/output) locked down to prevent
possible short circuits.
Note that most people get a reset button that is a hardware reset. The
software reset button is available on boards from Netgate.
Sponsored by: Rubicon Communications (Netgate)
if desired.
Retire randomdev_none.c and introduce random_infra.c for resident
infrastructure. Completely stub out random(4) calls in the "without
DEV_RANDOM" case.
Add RANDOM_LOADABLE option to allow loadable Yarrow/Fortuna/LocallyWritten
algorithm. Add a skeleton "other" algorithm framework for folks
to add their own processing code. NIST, anyone?
Retire the RANDOM_DUMMY option.
Build modules for Yarrow, Fortuna and "other".
Use atomics for the live entropy rate-tracking.
Convert ints to bools for the 'seeded' logic.
Move _write() function from the algorithm-specific areas to randomdev.c
Get rid of reseed() function - it is unused.
Tidy up the opt_*.h includes.
Update documentation for random(4) modules.
Fix test program (reviewers, please leave this).
Differential Revision: https://reviews.freebsd.org/D3354
Reviewed by: wblock,delphij,jmg,bjk
Approved by: so (/dev/random blanket)
It has nothing to share with too huge ctl.c other then device descriptor,
but even that may be counted as design error that may be fixed later.
At some point we may even want to have several ioctl ports.
Its idea was to be a simple initiator and execute several commands from
kernel level, but FreeBSD never had consumer for that functionality,
while its implementation polluted many unrelated places..
There are still several bugs, but I've been using it for a while now.
Thanks to all the testers and to Adrian for his help with this
driver.
This driver isn't connected to the build yet, but it will be soon.
There's no MFC planned because the driver isn't very stable yet.
Reviewed by: adrian
Obtained from: https://github.com/rpaulo/iwm
Tested by: adrian, gjb, dumbbell (others that I forgot).
Relnotes: yes
changes in the firmwares since 1.11.27.0 are listed here (straight copy-paste
from the "Release Notes.txt" accompanying the Chelsio Unified Wire 2.11.1.0
release on the website).
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.14.4.0
Date : 08/05/2015
================================================================================
FIXES
-----
BASE:
- Fixes a potential data path hang by properly programming PMTX congestion
threshold settings.
- Fixes a potential initialization error when accessing a configuration file
stored on the flash.
- Fixes a regression where SGE resources can be miss-sized if iWARP is disabled.
ETH:
- Fixes a timing issue that would prevent CR4 links from coming up with some
switches.
FOFCoE:
- Defers fcoe linkdown mailbox command handling till LOGO is sent.
- Updates vlan prio for all outstanding IOs during dcbx update.
ENHANCEMENTS
------------
BASE:
- Adds support for PAUSE OFF watchdog.
- Reports devlog access information in PCIE_FW_PF register 7.
ETH:
- Enhances segmentation offload to include VxLAN and Geneve.
- Adds PTP support.
- Adds new interface to allow the driver to query the VI rss table base
addresses.
- Allows the driver to program the SGE ingrext contxt CongDrop field.
OFLD:
- Adds new interface for the driver to specify offloaded connections TCP snd
and rcv scale factors.
iSCSI:
- Adds support for iscsi segmentatation offload (ISO).
- Adds support for iscsi t10-dif offload.
FOiSCSI:
- Sets FORCE_BIT for cut through processing for FOiSCSI.
FOFCoE:
- Adds support for FCoE BB6.
- Improves WRITE performance.
================================================================================
================================================================================
Version : 1.13.32.0
Date : 03/25/2015
================================================================================
FIXES
-----
BASE:
- Fixes FW_CAPS_CONFIG_CMD return value on error (was positive instead of
negative)
- Fixes FW_PARAMS_PARAM_DEV_FLOWC_BUFFIFO_SZ indication (was wrong on certain
adapter configurations)
- Fixes config file based PL_TIMEOUT register programming
ETH:
- Fixes a potential EO UDP SEG header corruption
- Fixes an issue where 1000Base-X was not enabled correctly when using QSA
modules
OFLD:
- Fixes timeout issue with half-open connections
- Fixes FW_FLOWC_WR processing when state is set to finwait1
FOFCoE:
- Fixes fcoe xchg leaks in linkdown/peer down path
- Fixes cleanup in FCoE linkdown and fixed buf timer flowid abuse
- Fixes fw crash by clearing fcf flowc during bye
FOiSCSI:
- Don't create a new tcp socket if ERL0 attempt has timed out.
ENHANCEMENTS
------------
BASE:
- Adds support for VFs on PFs 4 to 7
- Adds support for QPs/CQs on any physical and virtual function
ETH:
- Stops sending LACP frames on loopback interface
- Adds an AUTOEQU indication to CPL_SGE_EGR_UPDATE
- Adds support for CR4 links (BEAN/AEC on 40G TwinAx cables)
OFLD:
- Improves default settings of LAN and CLUSTER TCP timer settings
- Sends Negative Advice CPLs to software
FOISCSI:
- Adds IPv6 support for foiscsi. Keeps backward compatibility with
old foiscsi drivers which doesn't support ipv6.
FOFCoE:
- Added fcoe debug support in flowc dump
================================================================================
================================================================================
Version : 1.12.25.0
Date : 10/22/2014
================================================================================
FIXES
-----
BASE:
- Improves precision of the Weight Round Robing Traffic Management Algorithm
- Fixes an issue where the link would intermittently fail to come up
- Fixes an issue where adapters with an external PHY couldn't run at 100Mbps
- Fixes an issue where active optical cables were not recognized
- Fixes link advertising issues on T520-BT (speed and pause frames) that would
cause the link to negotiate unexpected settings
- Forces link restart when auto-negotiation is disabled
- Fix an issue where pause frames wouldn't be fully disabled even if requested
ETH:
- Fixes NVGRE Segmentation Offload network header generation.
DCBX:
- Fixes an issue where some settings were not being sent to the switch
correctly
- Fixes an issue where back-to-back DCBX port updates could get overwritten by
FW
- Fixes a firmware crash on DCBX APP information request before link up
FOiSCSI:
- Fixes abort task leak in tmf response handling
- Fixes TCP RST handling while in iSCSI ERL0
- Fixes a firmware crash on BYE without INIT
ENHANCEMENTS
-------------
BASE:
- Adds link partner settings reporting when available
- Adds QSA support (in conjunction with QSA VPD)
- Adds T520-BT LED support
- Reports NOTSUPPORTED for modules with an unhandled identifier
DCBX:
- Adds version reporting (indicating which version FW is trying to negotiate)
- Adds IEEE support
- Reports LLDP time outs
FOiSCSI:
- Add support for multiple iSCSI DDP client
- Sends DHCP renew request when lease expires
================================================================================
22.2. T4 Firmware
+++++++++++++++++
Version : 1.14.4.0
Date : 08/05/2015
================================================================================
FIXES
-----
BASE:
- Fixes a potential initialization error when accessing a configuration file
stored on the flash.
- Initialize PCIE_DBG_INDIR_REQ.Enable to 0, as hardware failed to do so and
register dumps could result in errors.
ETH:
- Fixes an issue that sometimes prevented the link from coming up in CR adapters.
ENHANCEMENTS
------------
BASE:
- Adds support for PAUSE OFF watchdog.
- Reports devlog access information in PCIE_FW_PF register 7.
ETH:
- Adds new interface to allow the driver to query the VI rss table base
addresses.
OFLD:
- Adds new interface for the driver to specify offloaded connections TCP snd
and rcv scale factors.
================================================================================
================================================================================
Version : 1.13.32.0
Date : 03/25/2015
================================================================================
FIXES
-----
BASE:
- Fixes FW_CAPS_CONFIG_CMD return value on error (was positive instead of
negative)
- Fixes FW_PARAMS_PARAM_DEV_FLOWC_BUFFIFO_SZ indication (was wrong on certain
adapter configurations)
- Fixes config file based PL_TIMEOUT register programming
ETH:
- Fixes a potential EO UDP SEG header corruption
OFLD:
- Fixes timeout issue with half-open connections
- Fixes FW_FLOWC_WR processing when state is set to finwait1
FOiSCSI:
- Don't create a new tcp socket if ERL0 attempt has timed out.
ENHANCEMENTS
------------
ETH:
- Stops sending LACP frames on loopback interface
- Adds an AUTOEQU indication to CPL_SGE_EGR_UPDATE
OFLD:
- Improves default settings of LAN and CLUSTER TCP timer settings
- Sends Negative Advice CPLs to software
================================================================================
================================================================================
Version : 1.12.25.0
Date : 10/22/2014
================================================================================
FIXES
-----
BASE:
- Improves precision of the Weight Round Robing Traffic Management Algorithm
- Forces link restart when auto-negotiation is disabled
- Fix an issue where pause frames wouldn't be fully disabled even if requested
DCBX:
- Fixes an issue where some settings were not being sent to the switch
correctly
- Fixes an issue where back-to-back DCBX port updates could get overwritten by
FW
- Fixes a firmware crash on DCBX APP information request before link up
FOiSCSI:
- Fixes abort task leak in tmf response handling
- Fixes TCP RST handling while in iSCSI ERL0
- Fixes a firmware crash on BYE without INIT
ENHANCEMENTS
------------
BASE:
- Adds link partner settings reporting when available
- Firmware now reports NOTSUPPORTED for modules with an unhandled identifier
DCBX:
- Adds version reporting (indicating which version FW is trying to negotiate)
- Adds IEEE support
- Reports LLDP time outs
FOiSCSI:
- Adds support for multiple iSCSI DDP clients
- Sends DHCP renew request when lease expires
================================================================================
Obtained from: Chelsio Communications
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Place all of the machine/pointer size independent code in a kernel
module called 'cloudabi'. All of the 64-bit specific code goes in a
separate module called 'cloudabi64'. The latter is only enabled on
amd64, as it is the only architecture supported.
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
lightly used. Find the proper .m file when we depend on *_if.[ch] in
the srcs line, with seat-belts for false positive matches. This uses
make's path mechanism. A further refinement would be to calculate this
once, and then pass the resulting _MPATH to modules submakes.
Differential Revision: https://reviews.freebsd.org/D2327
* GENERAL
- Update copyright.
- Make kernel options for RANDOM_YARROW and RANDOM_DUMMY. Set
neither to ON, which means we want Fortuna
- If there is no 'device random' in the kernel, there will be NO
random(4) device in the kernel, and the KERN_ARND sysctl will
return nothing. With RANDOM_DUMMY there will be a random(4) that
always blocks.
- Repair kern.arandom (KERN_ARND sysctl). The old version went
through arc4random(9) and was a bit weird.
- Adjust arc4random stirring a bit - the existing code looks a little
suspect.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Redo read_random(9) so as to duplicate random(4)'s read internals.
This makes it a first-class citizen rather than a hack.
- Move stuff out of locked regions when it does not need to be
there.
- Trim RANDOM_DEBUG printfs. Some are excess to requirement, some
behind boot verbose.
- Use SYSINIT to sequence the startup.
- Fix init/deinit sysctl stuff.
- Make relevant sysctls also tunables.
- Add different harvesting "styles" to allow for different requirements
(direct, queue, fast).
- Add harvesting of FFS atime events. This needs to be checked for
weighing down the FS code.
- Add harvesting of slab allocator events. This needs to be checked for
weighing down the allocator code.
- Fix the random(9) manpage.
- Loadable modules are not present for now. These will be re-engineered
when the dust settles.
- Use macros for locks.
- Fix comments.
* src/share/man/...
- Update the man pages.
* src/etc/...
- The startup/shutdown work is done in D2924.
* src/UPDATING
- Add UPDATING announcement.
* src/sys/dev/random/build.sh
- Add copyright.
- Add libz for unit tests.
* src/sys/dev/random/dummy.c
- Remove; no longer needed. Functionality incorporated into randomdev.*.
* live_entropy_sources.c live_entropy_sources.h
- Remove; content moved.
- move content to randomdev.[ch] and optimise.
* src/sys/dev/random/random_adaptors.c src/sys/dev/random/random_adaptors.h
- Remove; plugability is no longer used. Compile-time algorithm
selection is the way to go.
* src/sys/dev/random/random_harvestq.c src/sys/dev/random/random_harvestq.h
- Add early (re)boot-time randomness caching.
* src/sys/dev/random/randomdev_soft.c src/sys/dev/random/randomdev_soft.h
- Remove; no longer needed.
* src/sys/dev/random/uint128.h
- Provide a fake uint128_t; if a real one ever arrived, we can use
that instead. All that is needed here is N=0, N++, N==0, and some
localised trickery is used to manufacture a 128-bit 0ULLL.
* src/sys/dev/random/unit_test.c src/sys/dev/random/unit_test.h
- Improve unit tests; previously the testing human needed clairvoyance;
now the test will do a basic check of compressibility. Clairvoyant
talent is still a good idea.
- This is still a long way off a proper unit test.
* src/sys/dev/random/fortuna.c src/sys/dev/random/fortuna.h
- Improve messy union to just uint128_t.
- Remove unneeded 'static struct fortuna_start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
* src/sys/dev/random/yarrow.c src/sys/dev/random/yarrow.h
- Improve messy union to just uint128_t.
- Remove unneeded 'staic struct start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
- Fix some magic numbers elsewhere used as FAST and SLOW.
Differential Revision: https://reviews.freebsd.org/D2025
Reviewed by: vsevolod,delphij,rwatson,trasz,jmg
Approved by: so (delphij)
Added support for the following:
- iSCSI TLV (requires 64 Tx and 32 Rx rings
- 9K receive buffers for jumbo frames (feature may be enabled/disabled)
- builtin firmware, bootloader and minidump template
- quick stats
- async event handling for SFP insertion/removal and DCBX changes
- Configuring DCBX and interrupt coalescing parameters
code update, with supporting changes in the CORE. Changes for the extended
media types, VF driver has virtual channel protocol changes, and some
register use corrections. This software change should be coordinated with
Firmware updates to your hardware, contact your support channels for that.
MFC after: 1 week
up to 2 rx/tx queues for the 82574.
Program the 82574 to enable 5 msix vectors, assign 1 to each rx queue,
1 to each tx queue and 1 to the link handler.
Inspired by DragonFlyBSD, enable some RSS logic for handling tx queue
handling/processing.
Move multiqueue handler functions so that they line up better in a diff
review to if_igb.c
Always enqueue tx work to be done in em_mq_start, if unable to acquire
the TX lock, then this will be processed in the background later by the
taskqueue. Remove mbuf argument from em_start_mq_locked() as the work
is always enqueued. (stolen from igb)
Setup TARC, TXDCTL and RXDCTL registers for better performance and stability
in multiqueue and singlequeue implementations. Handle Intel errata 3 and
generic multiqueue behavior with the initialization of TARC(0) and TARC(1)
Bind interrupt threads to cpus in order. (stolen from igb)
Add 2 new DDB functions, one to display the queue(s) and their settings and
one to reset the adapter. Primarily used for debugging.
In the multiqueue configuration, bump RXD and TXD ring size to max for the
adapter (4096). Setup an RDTR of 64 and an RADV of 128 in multiqueue configuration
to cut down on the number of interrupts. RADV was arbitrarily set to 2x RDTR
and can be adjusted as needed.
Cleanup the display in top a bit to make it clearer where the taskqueue threads
are running and what they should be doing.
Ensure that both queues are processed by em_local_timer() by writing them both
to the IMS register to generate soft interrupts.
Ensure that an soft interrupt is generated when em_msix_link() is run so that
any races between assertion of the link/status interrupt and a rx/tx interrupt
are handled.
Document existing tuneables: hw.em.eee_setting, hw.em.msix, hw.em.smart_pwr_down, hw.em.sbp
Document use of hw.em.num_queues and the new kernel option EM_MULTIQUEUE
Thanks to Intel for their continued support of FreeBSD.
Reviewed by: erj jfv hiren gnn wblock
Obtained from: Intel Corporation
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D1994
NOTE: This is a technology preview, while it has undergone
development testing, Intel has not yet completed full
validation of the feature. It is being integrated for
early access and customer testing.
NOTE: This is a technology preview, while it has undergone development
tests, Intel has not yet completed full validation of the feature.
It is being integrated for early access and customer testing.
DEBUG_FLAGS are set to DEBUG option value when kernel is built.
For example, it is -g in GENERIC config to have debug symbols.
Also DEBUG_FLAGS are used to determine if ctfconvert should keep
debug symbols.
Since we redefined DEBUG_FLAGS, debug symbols were always missing.
ctfconvert complains about it during kernel build.
It is incorrect to append DEBUG_FLAGS, since if DEBUG has no -g (or
similar), we'll have no debug symbols and ctfconvert will complain.
If it incorrect to always have -g in our DEBUG_FLAGS, since debug
symbols presence should be controllable by kernel config.
So, just add disabled by default addition of -DDEBUG=1 to CFLAGS.
Reviewed by: imp
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D2666
Leaf drivers should not import the PCI bus interface to add IOV handling.
Instead, move the IOV client methods to a separate kobj interface.
Differential Revision: https://reviews.freebsd.org/D2584
Reviewed by: rstone
Support 7xxx adapters including firmware-assisted TSO and VLAN tagging:
- Solarflare Flareon Ultra 7000 series 10/40G adapters:
- Solarflare SFN7042Q QSFP+ Server Adapter
- Solarflare SFN7142Q QSFP+ Server Adapter
- Solarflare Flareon Ultra 7000 series 10G adapters:
- Solarflare SFN7022F SFP+ Server Adapter
- Solarflare SFN7122F SFP+ Server Adapter
- Solarflare SFN7322F Precision Time Synchronization Server Adapter
- Solarflare Flareon 7000 series 10G adapters:
- Solarflare SFN7002F SFP+ Server Adapter
Support utilities to configure adapters and update firmware.
The work is done by Solarflare developers
(Andy Moreton, Andrew Lee and many others),
Artem V. Andreev <Artem.Andreev at oktetlabs.ru> and me.
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 weeks
Causually read by: gnn
Differential Revision: https://reviews.freebsd.org/D2618
When building with gcc 4.9 and binutils 2.25,
using '--input' and '--output' returns an error
message:
objcopy: option `--input' is ambiguous
Reported by: Jenkins
1. Linux sigset always 64 bit on all platforms. In order to move Linux
sigset code to the linux_common module define it as 64 bit int. Move
Linux sigset manipulation routines to the MI path.
2. Move Linux signal number definitions to the MI path. In general, they
are the same on all platforms except for a few signals.
3. Map Linux RT signals to the FreeBSD RT signals and hide signal conversion
tables to avoid conversion errors.
4. Emulate Linux SIGPWR signal via FreeBSD SIGRTMIN signal which is outside
of allowed on Linux signal numbers.
PR: 197216
around kqueue() to implement epoll subset of functionality.
The kqueue user data are 32bit on i386 which is not enough for
epoll user data, so we keep user data in the proc emuldata.
Initial patch developed by rdivacky@ in 2007, then extended
by Yuri Victorovich @ r255672 and finished by me
in collaboration with mjg@ and jillies@.
Differential Revision: https://reviews.freebsd.org/D1092
thread emuldata to proc emuldata as it was originally intended.
As we can have both 64 & 32 bit Linuxulator running any eventhandler
can be called twice for us. To prevent this move eventhandlers code
from linux_emul.c to the linux_common.ko module.
Differential Revision: https://reviews.freebsd.org/D1073
following primary purposes:
1. Remove the dependency of linsysfs and linprocfs modules from linux.ko,
which will be architecture specific on amd64.
2. Incorporate into linux_common.ko general code for platforms on which
we'll support two Linuxulator modules (for both instruction set - 32 & 64 bit).
3. Move malloc(9) declaration to linux_common.ko, to enable getting memory
usage statistics properly.
Currently linux_common.ko incorporates a code from linux_mib.c and linux_util.c
and linprocfs, linsysfs and linux kernel modules depend on linux_common.ko.
Temporarily remove dtrace garbage from linux_mib.c and linux_util.c
Differential Revision: https://reviews.freebsd.org/D1072
In collaboration with: Vassilis Laganakos.
Reviewed by: trasz
exposes functions from kernel with proper DWARF CFI information so that
it becomes easier to unwind through them.
Using vdso is a mandatory for a thread cancelation && cleanup
on a modern glibc.
Differential Revision: https://reviews.freebsd.org/D1060
about kld filenames for network drivers that requires them to follow the
pattern of if_<foo>. This also fixes the existing documentation in the
manpage which says to use if_oce_load=YES in loader.conf.
PR: 199095
MFC after: 1 week
This supports e500v1, e500v2, and e500mc. Tested only on e500v2, but the
performance counters are identical across all, with e500mc having some
additional events.
Relnotes: Yes
The htree directory index is a highly desirable feature for research
purposes and was meant to improve performance in our ext2/3 driver.
Unfortunately our implementation has two problems:
- It never really delivered any performance improvement.
- It appears to corrupt the filesystem in undetermined circumstances.
Strictly speaking dir_index is not required for read/write support in
ext2/3 and our limited ext4 support still works fine without it.
Regain stability in the ext2 driver by removing it. We may need it back
(fixed) if we want to support encrypted ext4 support but thanks to the
wonders of version control we can always revert this change and bring it
back.
PR: 191895
PR: 198731
PR: 199309
MFC after: 5 days
This update brings few features:
o Support for the setmaster/dropmaster ioctls. For instance, they
are used to run multiple X servers simultaneously.
o Support for minor devices. The only user-visible change is a new
entry in /dev/dri but it is useless at the moment. This is a
first step to support render nodes [1].
The main benefit is to greatly reduce the diff with Linux (at the
expense of an unreadable commit diff). Hopefully, next upgrades will be
easier.
No updates were made to the drivers, beside adapting them to API
changes.
[1] https://en.wikipedia.org/wiki/Direct_Rendering_Manager#Render_nodes
Tested by: Many people
MFC after: 1 month
Relnotes: yes
- Split the driver into independent pf and vf loadables. This is
in preparation for SRIOV support which will be following shortly.
This also allows us to keep a seperate revision control over the
two parts, making for easier sustaining.
- Make the TX/RX code a shared/seperated file, in the old code base
the ixv code would miss fixes that went into ixgbe, this model
will eliminate that problem.
- The driver loadables will now match the device names, something that
has been requested for some time.
- Rather than a modules/ixgbe there is now modules/ix and modules/ixv
- It will also be possible to make your static kernel with only one
or the other for streamlined installs, or both.
Enjoy!
Submitted by: jfv and erj
The information is required for NIC update and config tools.
Submitted by: Artem V. Andreev <Artem.Andreev at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
drivers can use it. This avoids some code duplication. Add missing
default case to all switch statements while at it. Also move the
hashing of the IPv6 flow field to layer 4 because the IPv6 flow field
is constant on a per L4 connection basis and not on a per L3 network.
Differential Revision: https://reviews.freebsd.org/D1987
Sponsored by: Mellanox Technologies
MFC after: 1 month
KERNBUILDDIR. Come up with some sensible defaults (though listing them
in kmod.mk may be unwise -- we have no easy way to know what are the
best sensible defaults for everything so we just catch the big stuff).
Append SRCS.${opt} for each option in KERN_OPTS to SRCS to allow easy
conditional compilation. Append any notion of KERN_OPTS_EXTRA to the
list of kernel opts.
Differential Revision: https://reviews.freebsd.org/D1530
this option from all modules that enable it theirselves.
In C mode -fms-extensions option enables anonymous structs and unions,
allowing us to use this C11 feature in kernel. Of course, clang supports
it without any extra options.
Reviewed by: dim
Highlights:
- Multiple verbs API updates
- Support for RoCE, RDMA over ethernet
All hardware drivers depending on the common infiniband stack has been
updated aswell.
Discussed with: np @
Sponsored by: Mellanox Technologies
MFC after: 1 month
has been removed and the driver has been greatly simplified and
optimised for FreeBSD. The driver is currently not built by default.
Requested by: Bruce Simpson <bms@fastmail.net>
a dependency. This ensures "ifconfig cxl<n> ..." does the right thing
even when it's run with no driver loaded.
if_cxl.ko is the tiniest module in /boot/kernel.
MFC after: 2 weeks
commit 4d93914ae3db4a897ead4b. Some related drm infrastructure
changes are imported as needed.
Biggest update is the rewrite of the i915 gem io to more closely
follow Linux model, althought the mechanism used by FreeBSD port is
different.
Sponsored by: The FreeBSD Foundation
MFC after: 2 month
There needs to be some more testing done before it is ready for all
platforms and architectures.
MFC after: 1 month
Sponsored by: Mellanox Technologies
Reported by: bz@
by dumbbell@ to be able to compile this layer as a dependency module.
Clean up some Makefiles and remove the no longer used OFED define.
Currently only i386 and amd64 targets are supported.
MFC after: 1 month
Sponsored by: Mellanox Technologies
binary FPGA image that's in an include file in this directory, that
include file isn't actually used. It is only for certain Trump Cards
that we don't yet support. When support was anticipated for them, we
got permission to include the required FPGA image in our sources under
the BSDL, but didn't start actually including the file. This was done
to provide a public paper trail for this file.
would be picked up for kernel builds, it isn't picked up for
old-fashioned builds. Without this option, PCI bus numbers are busted
for modules build iteratively.
if_ixl to version 1.3.0, if_ixlv to version 1.2.0
- Major change in both drivers is to add RSS support
- In ixl fix some interface speed related issues, dual
speed was not changing correctly, KR/X media was not
displaying correctly (this has a workaround until a
more robust media handling is in place)
- Add a warning when using Dell NPAR and the speed is
less than 10G
- Wrap a queue hung message in IXL_DEBUG, as it is non-fatal,
and without tuning can display excessively
MFC after: 1 week
DCTCP congestion control algorithm aims to maximise throughput and minimise
latency in data center networks by utilising the proportion of Explicit
Congestion Notification (ECN) marked packets received from capable hardware as a
congestion signal.
Highlights:
Implemented as a mod_cc(4) module.
ECN (Explicit congestion notification) processing is done differently from
RFC3168.
Takes one-sided DCTCP into consideration where only one of the sides is using
DCTCP and other is using standard ECN.
IETF draft: http://tools.ietf.org/html/draft-bensley-tcpm-dctcp-00
Thesis report by Midori Kato: https://eggert.org/students/kato-thesis.pdf
Submitted by: Midori Kato <katoon@sfc.wide.ad.jp> and
Lars Eggert <lars@netapp.com>
with help and modifications from
hiren
Differential Revision: https://reviews.freebsd.org/D604
Reviewed by: gnn
fallback targets to build the aic generated files. fmake doesn't like
the current construct, and since it doesn't have .MAKE.LEVEL, just
don't provide the fallback targets for fmake. This gives a little
extra compatibility to old systems trying to build new kernels at
almost no cost to the current code.
of the scan API.
The eventual aim is to have 'ieee80211_scan.c' have the net80211 and
driver facing scan API to start, finish and continue doing scanning
while 'ieee80211_swscan.c' implements the software scanner that
runs the scan task, handles probe request/reply bits, configures
the VAP off-channel, changes channel and does the scanning bits.
For NICs that do no scanning at all, the existing code is needed.
ath(4) and most of the other NICs (dumb USB ones in particular)
do little to no scan offload - it's all done in software.
Some NICs may do single channel at a time scanning; I haven't really
checked them out in detail.
iwn(4), the upcoming 7260 driver stuff, the new Qualcomm Atheros
11ac chipsets and the Atheros mobile/USB full-offload chips all
have complete scan engines in firmware. We don't have to drive
any of it at all - the firmware just needs to be told what to scan,
when to scan, how long to scan. It'll take care of going off
channel, pausing TX/RX appropriately, sending sleep notification
to the AP, sending probe requests and handling probe responses.
It'll do passive/active scan itself. It's almost completely
transparent to the network stack - all we see are scan notifications
when it finishes scanning each channel and beacons/probe responses
when it does its thing. Once it's done we get a final notification
that the scan is complete, with some scan results in the message.
The iwn(4) NICs handle doing active scanning too as an option
and will handle waiting appropriately on 5GHz passive channels
before active scanning.
There's some more refactoring, tidying up and lock assertions to
sprinkle around to tidy this whole thing up before I turn swscan.c
into another set of ic methods to override by the driver or
alternate scan module. So in theory this is all one big no-op
commit. In theory.
Tested:
* iwn(4) 5200, STA mode
* ath(4) 6205, STA mode
* ath(4) - various NICs, AP mode
has support for the .codeXX directives). However, it is desirable, for
a time, to allow kernels to be built with clang 3.4. Historically, it
has been advantageous to allow stable X-1 to build kernels the old
way (so long as the impact of doing so is small), and this restores
that ability.
Also, centralize the addition of ${ASM_CFLAGS.${.IMPSRC}}, place it in
kern.mk rather than kern.pre.mk so that all modules can benefit, and
give the same treatment to CFLAGS in kern.mk as well.
CWARNFALGS.$file centrally so we don't have to have it in all the
places. Remove a few warning flags that are no longer needed.
Also, always use -Wno-unknown-pragma to (hopefully temporarily) work
around #pragma ident in debug.h in the opensolaris code. Remove some
stale warning suppression that's no longer necessary.
roughly 10 years, and the driver has not enjoyed any significant maintenance
since long before that. Despite well-meaning efforts from a number of
people, myself included, it never made the jump to 64-bit and was relegated
to the back-corners of i386. Now its frailty is hampering forward progress
with Clang. Any renewed engineering efforts are of course welcome and can
happen outside of the tree. No MFC of this is planned.
a) Front load as much work as possible in if_transmit, before any driver
lock or software queue has to get involved.
b) Replace buf_ring with a brand new mp_ring (multiproducer ring). This
is specifically for the tx multiqueue model where one of the if_transmit
producer threads becomes the consumer and other producers carry on as
usual. mp_ring is implemented as standalone code and it should be
possible to use it in any driver with tx multiqueue. It also has:
- the ability to enqueue/dequeue multiple items. This might become
significant if packet batching is ever implemented.
- an abdication mechanism to allow a thread to give up writing tx
descriptors and have another if_transmit thread take over. A thread
that's writing tx descriptors can end up doing so for an unbounded
time period if a) there are other if_transmit threads continuously
feeding the sofware queue, and b) the chip keeps up with whatever the
thread is throwing at it.
- accurate statistics about interesting events even when the stats come
at the expense of additional branches/conditional code.
The NIC txq lock is uncontested on the fast path at this point. I've
left it there for synchronization with the control events (interface
up/down, modload/unload).
c) Add support for "type 1" coalescing work request in the normal NIC tx
path. This work request is optimized for frames with a single item in
the DMA gather list. These are very common when forwarding packets.
Note that netmap tx in cxgbe already uses these "type 1" work requests.
d) Do not request automatic cidx updates every 32 descriptors. Instead,
request updates via bits in individual work requests (still every 32
descriptors approximately). Also, request an automatic final update
when the queue idles after activity. This means NIC tx reclaim is still
performed lazily but it will catch up quickly as soon as the queue
idles. This seems to be the best middle ground and I'll probably do
something similar for netmap tx as well.
e) Implement a faster tx path for WRQs (used by TOE tx and control
queues, _not_ by the normal NIC tx). Allow work requests to be written
directly to the hardware descriptor ring if room is available. I will
convert t4_tom and iw_cxgbe modules to this faster style gradually.
MFC after: 2 months
The new RTC emulation supports all interrupt modes: periodic, update ended
and alarm. It is also capable of maintaining the date/time and NVRAM contents
across virtual machine reset. Also, the date/time fields can now be modified
by the guest.
Since bhyve now emulates both the PIT and the RTC there is no need for
"Legacy Replacement Routing" in the HPET so get rid of it.
The RTC device state can be inspected via bhyvectl as follows:
bhyvectl --vm=vm --get-rtc-time
bhyvectl --vm=vm --set-rtc-time=<unix_time_secs>
bhyvectl --vm=vm --rtc-nvram-offset=<offset> --get-rtc-nvram
bhyvectl --vm=vm --rtc-nvram-offset=<offset> --set-rtc-nvram=<value>
Reviewed by: tychon
Discussed with: grehan
Differential Revision: https://reviews.freebsd.org/D1385
MFC after: 2 weeks
which means that the NFSCLIENT and NFSSERVER
kernel options will no longer work. This commit
only removes the kernel components. Removal of
unused code in the user utilities will be done
later. This commit does not include an addition
to UPDATING, but that will be committed in a
few minutes.
Discussed on: freebsd-fs
have been in the base for a while, so the gymnastics here aren't
needed. In addition, the bugs in subr_disk.c have been fixed since
2009, so there's no need for an identical copy of it in the tree
anymore. There's really no need to binary patch g_io_request, so let's
get rid of the code (not compiled in anymore) lest others think it is
a good idea.
for counter mode), and AES-GCM. Both of these modes have been added to
the aesni module.
Included is a set of tests to validate that the software and aesni
module calculate the correct values. These use the NIST KAT test
vectors. To run the test, you will need to install a soon to be
committed port, nist-kat that will install the vectors. Using a port
is necessary as the test vectors are around 25MB.
All the man pages were updated. I have added a new man page, crypto.7,
which includes a description of how to use each mode. All the new modes
and some other AES modes are present. It would be good for someone
else to go through and document the other modes.
A new ioctl was added to support AEAD modes which AES-GCM is one of them.
Without this ioctl, it is not possible to test AEAD modes from userland.
Add a timing safe bcmp for use to compare MACs. Previously we were using
bcmp which could leak timing info and result in the ability to forge
messages.
Add a minor optimization to the aesni module so that single segment
mbufs don't get copied and instead are updated in place. The aesni
module needs to be updated to support blocked IO so segmented mbufs
don't have to be copied.
We require that the IV be specified for all calls for both GCM and ICM.
This is to ensure proper use of these functions.
Obtained from: p4: //depot/projects/opencrypto
Relnotes: yes
Sponsored by: FreeBSD Foundation
Sponsored by: NetGate
In the old days callout(9) had 1 tick precision and that was inadequate
for some uses, e.g. DTrace profile module, so we had to emulate cyclic
API and behavior. Now we can directly use callout(9) in the very few
places where cyclic was used.
Differential Revision: https://reviews.freebsd.org/D1161
Reviewed by: gnn, jhb, markj
MFC after: 2 weeks
partitions. Several utilities still use this interface and require
additional information since gpart was activated than before. This
allows fsck of a UFS partition without having to specify it is UFS,
per historic behavior.
to the build in either sys/conf/files* or sys/modules/dpt/Makefile. Also,
it was denoted as "doesn't quite work yet" when the file was initially added
(which may account for it never having been hooked up to the build).
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
gcc requires variables to be initialised in two places. One of them
is correctly used only under the same conditional though.
For module builds properly check if the kernel supports INET or INET6,
as otherwise various mips kernels without IPv6 support would fail to build.
- Remove duplicated sources between standard part of the kernel and
module. In particular, it caused duplicated lock initialization and
sysctl registration, both having bad consequences.
- Add missed source files to module.
- Static part of the kernel provides randomdev module, not
random_adaptors. Correct dependencies.
- Use cdev modules declaration macros.
Approved by: secteam (delphij)
Reviewed by: markm
Split it into two modules: if_gre(4) for GRE encapsulation and
if_me(4) for minimal encapsulation within IP.
gre(4) changes:
* convert to if_transmit;
* rework locking: protect access to softc with rmlock,
protect from concurrent ioctls with sx lock;
* correct interface accounting for outgoing datagramms (count only payload size);
* implement generic support for using IPv6 as delivery header;
* make implementation conform to the RFC 2784 and partially to RFC 2890;
* add support for GRE checksums - calculate for outgoing datagramms and check
for inconming datagramms;
* add support for sending sequence number in GRE header;
* remove support of cached routes. This fixes problem, when gre(4) doesn't
work at system startup. But this also removes support for having tunnels with
the same addresses for inner and outer header.
* deprecate support for various GREXXX ioctls, that doesn't used in FreeBSD.
Use our standard ioctls for tunnels.
me(4):
* implementation conform to RFC 2004;
* use if_transmit;
* use the same locking model as gre(4);
PR: 164475
Differential Revision: D1023
No objections from: net@
Relnotes: yes
Sponsored by: Yandex LLC
-Improved VF stability, thanks to changes from Ryan Stone,
and Juniper.
- RSS fixes in the ixlv driver
- link detection in the ixlv driver
- New sysctl's added in ixl and ixlv
- reset timeout increased for ixlv
- stability fixes in detach
- correct media reporting
- Coverity warnings fixed
- Many small bug fixes
- VF Makefile modified - nvm shared code needed
- remove unused sleep channels in ixlv_sc struct
Submitted by: Eric Joyner (committed by jfv)
MFC after: 1 week
problems than it solves. SYSDIR is already defined almost always and
can be used instead. Working around the one case where it isn't is
much easier than working around the fact that @ may not exist in 18
other places.
Differential Revision: https://reviews.freebsd.org/D1100
This code has had an extensive rewrite and a good series of reviews, both by the author and other parties. This means a lot of code has been simplified. Pluggable structures for high-rate entropy generators are available, and it is most definitely not the case that /dev/random can be driven by only a hardware souce any more. This has been designed out of the device. Hardware sources are stirred into the CSPRNG (Yarrow, Fortuna) like any other entropy source. Pluggable modules may be written by third parties for additional sources.
The harvesting structures and consequently the locking have been simplified. Entropy harvesting is done in a more general way (the documentation for this will follow). There is some GREAT entropy to be had in the UMA allocator, but it is disabled for now as messing with that is likely to annoy many people.
The venerable (but effective) Yarrow algorithm, which is no longer supported by its authors now has an alternative, Fortuna. For now, Yarrow is retained as the default algorithm, but this may be changed using a kernel option. It is intended to make Fortuna the default algorithm for 11.0. Interested parties are encouraged to read ISBN 978-0-470-47424-2 "Cryptography Engineering" By Ferguson, Schneier and Kohno for Fortuna's gory details. Heck, read it anyway.
Many thanks to Arthur Mesh who did early grunt work, and who got caught in the crossfire rather more than he deserved to.
My thanks also to folks who helped me thresh this out on whiteboards and in the odd "Hallway track", or otherwise.
My Nomex pants are on. Let the feedback commence!
Reviewed by: trasz,des(partial),imp(partial?),rwatson(partial?)
Approved by: so(des)
This reduces variability during timer calibration by keeping the emulation
"close" to the guest. Additionally having all timer emulations in the kernel
will ease the transition to a per-VM clock source (as opposed to using the
host's uptime keep track of time).
Discussed with: grehan
Support for the multiport feature is mostly implemented, but currently
disabled due to some potential races in the hot plug code paths.
Requested by: marcel
MFC after: 1 month
Relnotes: yes
vxlan creates a virtual LAN by encapsulating the inner Ethernet frame in
a UDP packet. This implementation is based on RFC7348.
Currently, the IPv6 support is not fully compliant with the specification:
we should be able to receive UPDv6 packets with a zero checksum, but we
need to support RFC6935 first. Patches for this should come soon.
Encapsulation protocols such as vxlan emphasize the need for the FreeBSD
network stack to support batching, GRO, and GSO. Each frame has to make
two trips through the network stack, and each frame will be at most MTU
sized. Performance suffers accordingly.
Some latest generation NICs have begun to support vxlan HW offloads that
we should also take advantage of. VIMAGE support should also be added soon.
Differential Revision: https://reviews.freebsd.org/D384
Reviewed by: gnn
Relnotes: yes
Rename vmx_assym.s to vmx_assym.h to reflect that file's actual use
and update vmx_support.S's include to match. Add vmx_assym.h to the
SRCS to that it gets properly added to the dependency list. Add
vmx_support.S to SRCS as well, so it gets built and needs fewer
special-case goo. Remove now-redundant special-case goo. Finally,
vmx_genassym.o doesn't need to depend on a hand expanded ${_ILINKS}
explicitly, that's all taken care of by beforedepend.
With these items fixed, we no longer build vmm.ko every single time
through the modules on a KERNFAST build.
Sponsored by: Netflix
entry and remove now-redunant dependencies. Add assym.s to
linux*_locore.s build, as it depends on it.
With this change, linux*.ko no longer builds every time through a
KERNFAST run.
Sponsored by: Netflix
Main user-visible changes are related to tables:
* Tables are now identified by names, not numbers.
There can be up to 65k tables with up to 63-byte long names.
* Tables are now set-aware (default off), so you can switch/move
them atomically with rules.
* More functionality is supported (swap, lock, limits, user-level lookup,
batched add/del) by generic table code.
* New table types are added (flow) so you can match multiple packet fields at once.
* Ability to add different type of lookup algorithms for particular
table type has been added.
* New table algorithms are added (cidr:hash, iface:array, number:array and
flow:hash) to make certain types of lookup more effective.
* Table value are now capable of holding multiple data fields for
different tablearg users
Performance changes:
* Main ipfw lock was converted to rmlock
* Rule counters were separated from rule itself and made per-cpu.
* Radix table entries fits into 128 bytes
* struct ip_fw is now more compact so more rules will fit into 64 bytes
* interface tables uses array of existing ifindexes for faster match
ABI changes:
All functionality supported by old ipfw(8) remains functional.
Old & new binaries can work together with the following restrictions:
* Tables named other than ^\d+$ are shown as table(65535) in
ruleset in old binaries
Internal changes:.
Changing table ids to numbers resulted in format modification for
most sockopt codes. Old sopt format was compact, but very hard to
extend (no versioning, inability to add more opcodes), so
* All relevant opcodes were converted to TLV-based versioned IP_FW3-based codes.
* The remaining opcodes were also converted to be able to eliminate
all older opcodes at once
* All IP_FW3 handlers uses special API instead of calling sooptcopy*
directly to ease adding another communication methods
* struct ip_fw is now different for kernel and userland
* tablearg value has been changed to 0 to ease future extensions
* table "values" are now indexes in special value array which
holds extended data for given index
* Batched add/delete has been added to tables code
* Most changes has been done to permit batched rule addition.
* interface tracking API has been added (started on demand)
to permit effective interface tables operations
* O(1) skipto cache, currently turned off by default at
compile-time (eats 512K).
* Several steps has been made towards making libipfw:
* most of new functions were separated into "parse/prepare/show
and actuall-do-stuff" pieces (already merged).
* there are separate functions for parsing text string into "struct ip_fw"
and printing "struct ip_fw" to supplied buffer (already merged).
* Probably some more less significant/forgotten features
MFC after: 1 month
Sponsored by: Yandex LLC
snv add, so I have added $FreeBSD$ as comment.
This commit is contininous of last mrsas commit, so that compilation
does not break.
Obtained from: AVAGO Technologies
MFC after: 2 weeks
machine, for which 32bit compatibilty code has been added.
As in linux there is only one device entry that is used to fire IOCTL commands,
a new device entry megaraid_sas_ioctl_node is added for solely this
purpose.
From one dev node i.e mrgaraid_sa_ioctl_node we have to find out the
controller instance in case of multicontroller, for which one management info
structure has been added.
Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies
For now restrict it to amd64. Other architectures might be
re-added later once tested.
Remove the drivers from the global NOTES and files files and move
them to the amd64 specifics.
Remove the drivers from the i386 modules build and only leave the
amd64 version.
Rather than depending on "inet" depend on "pci" and make sure that
ixl(4) and ixlv(4) can be compiled independently [2]. This also
allows the drivers to build properly on IPv4-only or IPv6-only
kernels.
PR: 193824 [2]
Reviewed by: eric.joyner intel.com
MFC after: 3 days
References:
[1] http://lists.freebsd.org/pipermail/svn-src-all/2014-August/090470.html
code. There are only a handful of MSRs common between the two so there isn't
too much duplicate functionality.
The VT-x code has the following types of MSRs:
- MSRs that are unconditionally saved/restored on every guest/host context
switch (e.g., MSR_GSBASE).
- MSRs that are restored to guest values on entry to vmx_run() and saved
before returning. This is an optimization for MSRs that are not used in
host kernel context (e.g., MSR_KGSBASE).
- MSRs that are emulated and every access by the guest causes a trap into
the hypervisor (e.g., MSR_IA32_MISC_ENABLE).
Reviewed by: grehan
for amd64/linux32. Fix the entirely bogus (untested) version from
r161310 for i386/linux using the same shared code in compat/linux.
It is unclear to me if we could support more clock mappings but
the current set allows me to successfully run commercial
32bit linux software under linuxolator on amd64.
Reviewed by: jhb
Differential Revision: D784
MFC after: 3 days
Sponsored by: DARPA, AFRL
This feature is required by Mesa 9.2+. Without this, a GL application
crashes with the following message:
# glxinfo
name of display: :0.0
Gen6+ requires Kernel 3.6 or later.
Assertion failed: (ctx->Version > 0), function handle_first_current,
file ../../src/mesa/main/context.c, line 1498.
Abort (core dumped)
Now, Mesa 10.2.4 and 10.3-rc3 works fine:
# glxinfo
name of display: :0
display: :0 screen: 0
direct rendering: Yes
...
OpenGL renderer string: Mesa DRI Intel(R) 965GM
OpenGL version string: 2.1 Mesa 10.2.4
...
The code was imported from Linux 3.8.13.
Reviewed by: kib@
Tested by: kwm@, danfe@, Henry Hu,
Lundberg, Johannes <johannes@brilliantservice.co.jp>,
Johannes Dieterich <dieterich.joh@gmail.com>,
Lutz Bichler <lutz.bichler@gmail.com>,
MFC after: 3 days
Relnotes: yes
The flowdirector feature shares on-chip memory with other things
such as the RX buffers. In theory it should be configured in a way
that doesn't interfere with the rest of operation. In practice,
the RX buffer calculation didn't take the flow-director allocation
into account and there'd be overlap. This lead to various garbage
frames being received containing what looks like internal NIC state.
What _I_ saw was traffic ending up in the wrong RX queues.
If I was doing a UDP traffic test with only one NIC ring receiving
traffic, everything is fine. If I fired up a second UDP stream
which came in on another ring, there'd be a few percent of traffic
from both rings ending up in the wrong ring. Ie, the RSS hash would
indicate it was supposed to come in ring X, but it'd come in ring Y.
However, when the allocation was fixed up, the developers at Verisign
still saw traffic stalls.
The flowdirector feature ends up fiddling with the NIC to do various
attempts at load balancing connections by populating flow table rules
based on sampled traffic. It's likely that all of that has to be
carefully reviewed and made less "magic".
So for now the flow director feature is disabled (which fixes both
what I was seeing and what they were seeing) until it's all much
more debugged and verified.
Tested:
* (me) 82599EB 2x10G NIC, RSS UDP testing.
* (verisign) not sure on the NIC (but likely 82599), 100k-200k/sec TCP
transaction tests.
Submitted by: Marc De La Gueronniere <mdelagueronniere@verisign.com>
MFC after: 1 week
Sponsored by: Verisign, Inc.
many thanks for their continued support of FreeBSD.
While I'm there, also implement a new build knob, WITHOUT_HYPERV to
disable building and installing of the HyperV utilities when necessary.
The HyperV utilities are only built for i386 and amd64 targets.
This is a stable/10 candidate for inclusion with 10.1-RELEASE.
Submitted by: Wei Hu <weh microsoft com>
MFC after: 1 week
PCI IDs into quirks, which mostly fit (though you'd get no argument
from me that AHCI_Q_SATA1_UNIT0 is oddly specific). Set these quirks
in the PCI attachment. Make some shared functions public so that PCI
and possibly other bus attachments can use them.
The split isn't perfect yet, but it is functional. The split will be
perfected as other bus attachments for AHCI are written.
Sponsored by: Netflix
Reviewed by: kan, mav
Differential Revision: https://reviews.freebsd.org/D699
This is the last major change in given branch.
Kernel changes:
* Use 64-bytes structures to hold multi-value variables.
* Use shared array to hold values from all tables (assume
each table algo is capable of holding 32-byte variables).
* Add some placeholders to support per-table value arrays in future.
* Use simple eventhandler-style API to ease the process of adding new
table items. Currently table addition may required multiple UH drops/
acquires which is quite tricky due to atomic table modificatio/swap
support, shared array resize, etc. Deal with it by calling special
notifier capable of rolling back state before actually performing
swap/resize operations. Original operation then restarts itself after
acquiring UH lock.
* Bump all objhash users default values to at least 64
* Fix custom hashing inside objhash.
Userland changes:
* Add support for dumping shared value array via "vlist" internal cmd.
* Some small print/fill_flags dixes to support u32 values.
* valtype is now bitmask of
<skipto|pipe|fib|nat|dscp|tag|divert|netgraph|limit|ipv4|ipv6>.
New values can hold distinct values for each of this types.
* Provide special "legacy" type which assumes all values are the same.
* More helpers/docs following..
Some examples:
3:41 [1] zfscurr0# ipfw table mimimi create valtype skipto,limit,ipv4,ipv6
3:41 [1] zfscurr0# ipfw table mimimi info
+++ table(mimimi), set(0) +++
kindex: 2, type: addr
references: 0, valtype: skipto,limit,ipv4,ipv6
algorithm: addr:radix
items: 0, size: 296
3:42 [1] zfscurr0# ipfw table mimimi add 10.0.0.5 3000,10,10.0.0.1,2a02:978:2::1
added: 10.0.0.5/32 3000,10,10.0.0.1,2a02:978:2::1
3:42 [1] zfscurr0# ipfw table mimimi list
+++ table(mimimi), set(0) +++
10.0.0.5/32 3000,0,10.0.0.1,2a02:978:2::1
The firmware is from the Linux firmware git repository; the intel
licence is the same as other firmware blobs.
Tested: iwn1: <Intel Centrino Wireless-N 100> mem 0xf4800000-0xf4801fff irq 19 at device 0.0 on pci5
hardware driver update from Mellanox Technologies.
- Remove empty files from the OFED Linux Emulation layer.
- Fix compile warnings related to printf() and the "%lld" and "%llx"
format specifiers.
- Add some missing 2-clause BSD copyrights.
- Add "Mellanox Technologies, Ltd." to list of copyright holders.
- Add some new compatibility files.
- Fix order of uninit in the mlx4ib module to avoid crash at unload
using the new module_exit_order() function.
MFC after: 1 week
Sponsored by: Mellanox Technologies
- It was decided to change the driver name to if_ixl for FreeBSD
- This release adds the VF Driver to the tree, it can be built into
the kernel or as the if_ixlv module
- The VF driver is independent for the first time, this will be
desireable when full SRIOV capability is added to the OS.
- Thanks to my new coworker Eric Joyner for his superb work in
both the core and vf driver code.
Enjoy everyone!
Submitted by: jack.vogel@intel.com and eric.joyner@intel.com
MFC after: 3 days (hoping to make 10.1)
We haven't noticed that it was missing because eisa has been disabled for
a while in -current, but it became apparent when some parallel-build stuff
was MFC'd to 10-stable and this module failed to build there.
UNIX systems, eg. MacOS X and Solaris. It uses Sun-compatible map format,
has proper kernel support, and LDAP integration.
There are still a few outstanding problems; they will be fixed shortly.
Reviewed by: allanjude@, emaste@, kib@, wblock@ (earlier versions)
Phabric: D523
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
duplicating the entire implementation for both x86 and powerpc. This makes
it easier to add support for other architectures and has no functional
impact.
Phabric: D613
Reviewed by: gnn, jhibbits, rpaulo
Tested by: jhibbits (powerpc)
MFC after: 2 weeks
options into kern.opts.mk and change all the places where we use
src.opts.mk to pull in the options. Conditionally define SYSDIR and
use SYSDIR/conf/kern.opts.mk instead of a CURDIR path. Replace all
instances of CURDIR/../../etc with STSDIR, but only in the affected
files.
As a special compatibility hack, include bsd.owm.mk at the top of
kern.opts.mk to allow the bare build of sys/modules to work on older
systems. If the defaults ever change between 9.x, 10.x and current for
these options, however, you'll wind up with the host OS' defaults
rather than the -current defaults. This hack will be removed when
we no longer need to support this build scenario.
Reviewed by: jhb
Differential Revision: https://phabric.freebsd.org/D529
we set MK_INET6_SUPPORT to no, not if we do define INET6.
This way we do not try to build IPv6 parts in if the kernel doesn't support
them.
This unbreaks several kernel configurations building modules but no INET6.
opt_inet6.h into kmod.mk by forcing almost everybody to eat the same
dogfood. While at it, consolidate the opt_bpf.h and opt_mroute.h
targets here too.
* Rewrite interface tables to use interface indexes
Kernel changes:
* Add generic interface tracking API:
- ipfw_iface_ref (must call unlocked, performs lazy init if needed, allocates
state & bumps ref)
- ipfw_iface_add_ntfy(UH_WLOCK+WLOCK, links comsumer & runs its callback to
update ifindex)
- ipfw_iface_del_ntfy(UH_WLOCK+WLOCK, unlinks consumer)
- ipfw_iface_unref(unlocked, drops reference)
Additionally, consumer callbacks are called in interface withdrawal/departure.
* Rewrite interface tables to use iface tracking API. Currently tables are
implemented the following way:
runtime data is stored as sorted array of {ifidx, val} for existing interfaces
full data is stored inside namedobj instance (chained hashed table).
* Add IP_FW_XIFLIST opcode to dump status of tracked interfaces
* Pass @chain ptr to most non-locked algorithm callbacks:
(prepare_add, prepare_del, flush_entry ..). This may be needed for better
interaction of given algorithm an other ipfw subsystems
* Add optional "change_ti" algorithm handler to permit updating of
cached table_info pointer (happens in case of table_max resize)
* Fix small bug in ipfw_list_tables()
* Add badd (insert into sorted array) and bdel (remove from sorted array) funcs
Userland changes:
* Add "iflist" cmd to print status of currently tracked interface
* Add stringnum_cmp for better interface/table names sorting
This allows to clone VMs and move them between LUNs inside one storage
host without generating extra network traffic to the initiator and back,
and without being limited by network bandwidth.
LUNs participating in copy operation should have UNIQUE NAA or EUI IDs set.
For LUNs without these IDs VMWare will use traditional copy operations.
Beware: the above LUN IDs explicitly set to values non-unique from the VM
cluster point of view may cause data corruption if wrong LUN is addressed!
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
This includes:
o All directories named *ia64*
o All files named *ia64*
o All ia64-specific code guarded by __ia64__
o All ia64-specific makefile logic
o Mention of ia64 in comments and documentation
This excludes:
o Everything under contrib/
o Everything under crypto/
o sys/xen/interface
o sys/sys/elf_common.h
Discussed at: BSDcan
into head. The code is not believed to have any effect
on the semantics of non-NFSv4.1 server behaviour.
It is a rather large merge, but I am hoping that there will
not be any regressions for the NFS server.
MFC after: 1 month
MFV r260708
4427 pid provider rejects probes with valid UTF-8 names
Use of u8_textprep.c broke the build on powerpc.
Reported by: bz, rpaulo and tinderbox.
Pointyhat: me
configs. Switch the BERI_NETFPGA_MDROOT to 64bit by default.
Give we have working interrupts also cleanup the extra polling CFLAGS from
the module Makefile.
MFC after: 2 weeks
4427 pid provider rejects probes with valid UTF-8 names
This make use of Solaris' u8_validate() which we happen to
use since r185029 for ZFS.
Illumos Revision: 1444d846b126463eb1059a572ff114d51f7562e5
Reference:
https://www.illumos.org/issues/4427
Obtained from: Illumos
MFC after: 2 weeks
This partitioning scheme is used in DragonFlyBSD. It is similar to
BSD disklabel, but has the following improvements:
* metadata has own dedicated place and isn't accessible through partitions;
* all offsets are 64-bit;
* supports 16 partitions by default (has reserved place for more);
* has reserved place for backup label (but not yet implemented);
* has UUIDs for partitions and partition types;
No objections from: geom
MFC after: 2 weeks
Relnotes: yes
using a direct hook called from kern_vfs_bio_buffer_alloc().
Mark ffs_rawread.c as requiring both ffs and directio options to be
compiled into the kernel. Add ffs_rawread.c to the list of ufs.ko
module' sources.
In addition to stopping breaking the layering violation, it also
allows to link kernel when FFS is configured as module and DIRECTIO is
enabled.
One consequence of the change is that ffs_rawread.o is always linked
into the module regardless of the DIRECTIO option. This is similar to
the option QUOTA and ufs_quota.c.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- Update FDT file for BERI DE4 boards.
- Add needed kernel configuration keywords.
- Rename module to saf1761otg so that the device unit number does not
interfere with the hardware ID in dmesg.
Sponsored by: DARPA, AFRL
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.
For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.
With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.
trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43🆎cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43🆎cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...
Relnotes: Yes
Sponsored by: Chelsio Communications.
The CUSE library is a wrapper for the devfs kernel functionality which
is exposed through /dev/cuse . In order to function the CUSE kernel
code must either be enabled in the kernel configuration file or loaded
separately as a module. Currently none of the committed items are
connected to the default builds, except for installing the needed
header files. The CUSE code will be connected to the default world and
kernel builds in a follow-up commit.
The CUSE module was written by Hans Petter Selasky, somewhat inspired
by similar functionality found in FUSE. The CUSE library can be used
for many purposes. Currently CUSE is used when running Linux kernel
drivers in user-space, which need to create a character device node to
communicate with its applications. CUSE has full support for almost
all devfs functionality found in the kernel:
- kevents
- read
- write
- ioctl
- poll
- open
- close
- mmap
- private per file handle data
Requested by several people. Also see "multimedia/cuse4bsd-kmod" in
ports.
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
Intel 40G Ethernet Controller XL710 Family. This is
the core driver, a VF driver called i40evf, will be
following soon. Questions or comments to myself or
my co-developer Eric Joyner. Cheers!
audio device driver is detached first and not its children. This fixes
a panic in some cases when unloading "snd_uaudio" while a USB device
is plugged. The linking order affects the order in which the module
dependencies are registered.
MFC after: 1 week
cards. LSI has been maintaining this driver outside of the FreeBSD
tree. It overlaps support of ThunderBolt and Invader cards that mfi(4)
supports. By default mfi(4) will attach to cards. If the tunable:
hw.mfi.mrsas_enable=1
is set then mfi(4) will not probe and attach to these newer cards and
allow mrsas(4) to attach. So by default this driver will not effect
a FreeBSD system unless mfi(4) is removed from the kernel or the
tunable is enabled.
mrsas(4) attaches disks to the CAM layer so it depends on CAM and devices
show up as /dev/daX. mfiutil(8) does not work with mrsas. The FreeBSD
version of MegaCli and StorCli from LSI do work with mrsas. It appears
that StorCli only works with mrsas. MegaCli appears to work with mfi(4)
and mrsas(4).
It would be good to add mfiutil(4) support to mrsas, emulations modes,
kernel logging, device aliases to ease the transition between mfi(4)
and mrsas(4).
Style issues should be resolved by LSI when they get committers approved.
The plan is get this driver in FreeBSD 9.3 to improve HW support.
Thanks to LSI for developing, testing and working with FreeBSD to
make this driver co-exist in FreeBSD. This improves the overall
support of MegaRAID SAS.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: scottl
MFC after: 3 days
Sponsored by: LSI
platforms, because these platforms do not implement the ISA DMA
API. Else the sound modules cannot be loaded when running these
platforms.
MFC after: 2 weeks
This allows to run 32bit applications on a 64bit host. This was tested
successfully with Wine (emulators/i386-wine-devel) and StarCraft II.
Submitted by: Jan Kokemüller <jan.kokemueller@gmail.com>
MFC after: 1 week
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
It exposes I/O resources to user space, so that programs can peek
and poke at the hardware. It does not itself have knowledge about
the hardware device it attaches to.
Sponsored by: Juniper Networks, Inc.
NetFPGA-10G Embedded CPU Ethernet Core.
The current version operates on a simple PIO based interface connected
to a NetFPGA-10G port.
To avoid confusion: this driver operates on a CPU running on the FPGA,
e.g. BERI/mips, and is not suited for the PCI host interface.
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA/AFRL
binmisc code to be build on amd64/i386 for the kernel.
Update NOTES with some indication of what this code is used for.
Pointed out by jhb@ ... thanks!
Submitted by: jhb@
execution to a emumation program via parsing of ELF header information.
With this kernel module and userland tool, poudriere is able to build
ports packages via the QEMU userland tools (or another emulator program)
in a different architecture chroot, e.g. TARGET=mips TARGET_ARCH=mips
I'm not connecting this to GENERIC for obvious reasons, but this should
allow the kernel module to be built by default and enable the building
of the userland tool (which automatically loads the kernel module).
Submitted by: sson@
Reviewed by: jhb@
systems need fine-grained control over what's in and what's out.
That's ideal. For now, separate GPT labels from the rest and allow
g_label to be built with just GPT labels.
Obtained from: Juniper Networks, Inc.
As a prerequisite for multiple queues, the guest must have MSIX enabled.
Unfortunately, to work around device passthrough bugs, FreeBSD disables
MSIX when running as a VMWare guest due to the hw.pci.honor_msi_blacklist
tunable; this tunable must be disabled for multiple queues.
Also included is various minor changes from the projects/vmxnet branch.
MFC after: 1 month
AppleTalk was a network transport protocol for Apple Macintosh devices
in 80s and then 90s. Starting with Mac OS X in 2000 the AppleTalk was
a legacy protocol and primary networking protocol is TCP/IP. The last
Mac OS X release to support AppleTalk happened in 2009. The same year
routing equipment vendors (namely Cisco) end their support.
Thus, AppleTalk won't be supported in FreeBSD 11.0-RELEASE.
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
New ioctls VM_ISA_ASSERT_IRQ, VM_ISA_DEASSERT_IRQ and VM_ISA_PULSE_IRQ
can be used to manipulate the pic, and optionally the ioapic, pin state.
Reviewed by: jhb, neel
Approved by: neel (co-mentor)
relative to .CURDIR if not already defined. This makes the makefiles
more readable but also more re-usable and adaptable.
Obtained from: Juniper Networks, Inc.
This brings in the "-w" option from bhyve to ignore unknown MSRs.
It will make debugging Linux guests a bit easier.
Suggested by: Willem Jan Withagen (wjw at digiware nl)
- netmap pipes, providing bidirectional blocking I/O while moving
100+ Mpps between processes using shared memory channels
(no mistake: over one hundred million. But mind you, i said
*moving* not *processing*);
- kqueue support (BHyVe needs it);
- improved user library. Just the interface name lets you select a NIC,
host port, VALE switch port, netmap pipe, and individual queues.
The upcoming netmap-enabled libpcap will use this feature.
- optional extra buffers associated to netmap ports, for applications
that need to buffer data yet don't want to make copies.
- segmentation offloading for the VALE switch, useful between VMs.
and a number of bug fixes and performance improvements.
My colleagues Giuseppe Lettieri and Vincenzo Maffione did a substantial
amount of work on these features so we owe them a big thanks.
There are some external repositories that can be of interest:
https://code.google.com/p/netmap
our public repository for netmap/VALE code, including
linux versions and other stuff that does not belong here,
such as python bindings.
https://code.google.com/p/netmap-libpcap
a clone of the libpcap repository with netmap support.
With this any libpcap client has access to most netmap
feature with no recompilation. E.g. tcpdump can filter
packets at 10-15 Mpps.
https://code.google.com/p/netmap-ipfw
a userspace version of ipfw+dummynet which uses netmap
to send/receive packets. Speed is up in the 7-10 Mpps
range per core for simple rulesets.
Both netmap-libpcap and netmap-ipfw will be merged upstream at some
point, but while this happens it is useful to have access to them.
And yes, this code will be merged soon. It is infinitely better
than the version currently in 10 and 9.
MFC after: 3 days
Useful for so-called USB tethering.
- Imported code from OpenBSD
- Adapted code to FreeBSD
- Removed some unused functions
- Fixed some buffer encoding and decoding issues
- Optimised data transport path a bit, by sending multiple packets at a time
- Increased receive buffer to 16K
Obtained from: OpenBSD
Requested by: eadler @
MFC after: 2 weeks
Fix geom_uncompress(4) module loading. Don't link zlib.c (which is a module
itself) directly.
The built module was verified and used to read a few mkulzma(8) images on
amd64 to validate some of the informations on the manual page.
While here, don't overwrite CFLAGS.
Reviewed by: ray
Approved by: adrian (mentor)
drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
modules which require this flag to compile. Use a GCC_MS_EXTENSIONS
variable, defined in kern.pre.mk, which can be used to easily supply the
flag (or not), depending on the compiler type.
MFC after: 3 days
is only to stop gcc complaining about anonymous unions, which clang does
not do. For clang 3.4 however, -fms-extensions enables the Microsoft
__wchar_t type, which clashes with our own types.h.
MFC after: 3 days
- Add 'hyperv' module into build;
- Allow building Hyper-V support as part of the kernel;
- Hook Hyper-V build into NOTES.
This is intended for MFC if re@ permits.
MFC after: 3 days
bhyve supports a single timer block with 8 timers. The timers are all 32-bit
and capable of being operated in periodic mode. All timers support interrupt
delivery using MSI. Timers 0 and 1 also support legacy interrupt routing.
At the moment the timers are not connected to any ioapic pins but that will
be addressed in a subsequent commit.
This change is based on a patch from Tycho Nightingale (tycho.nightingale@pluribusnetworks.com).
option, unbreak the lock tracing release semantic by embedding
calls to LOCKSTAT_PROFILE_RELEASE_LOCK() direclty in the inlined
version of the releasing functions for mutex, rwlock and sxlock.
Failing to do so skips the lockstat_probe_func invokation for
unlocking.
- As part of the LOCKSTAT support is inlined in mutex operation, for
kernel compiled without lock debugging options, potentially every
consumer must be compiled including opt_kdtrace.h.
Fix this by moving KDTRACE_HOOKS into opt_global.h and remove the
dependency by opt_kdtrace.h for all files, as now only KDTRACE_FRAMES
is linked there and it is only used as a compile-time stub [0].
[0] immediately shows some new bug as DTRACE-derived support for debug
in sfxge is broken and it was never really tested. As it was not
including correctly opt_kdtrace.h before it was never enabled so it
was kept broken for a while. Fix this by using a protection stub,
leaving sfxge driver authors the responsibility for fixing it
appropriately [1].
Sponsored by: EMC / Isilon storage division
Discussed with: rstone
[0] Reported by: rstone
[1] Discussed with: philip
adapters. Both devices support Gigabit Ethernet and USB 2.0, and the AX88179
supports USB 3.0. The driver was written by kevlo@ and lwhsu@, with a few
bug fixes from me.
MFC after: 2 months
upcoming in-kernel device emulations like the HPET.
The ioctls VM_IOAPIC_ASSERT_IRQ and VM_IOAPIC_DEASSERT_IRQ are used to
manipulate the ioapic pin state.
Discussed with: grehan@
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
in the kernel. This abstraction was redundant because the only device emulated
inside vmm.ko is the local apic and it is always at a fixed guest physical
address.
Discussed with: grehan
components instead of with the kernel and/or modules. This ensures that it
gets built with the host compiler, not the compiler in obj/... used to build
the target components (which may be a cross-compiler outputting code for a
different architecture and using header files with types and options set up
for the wrong architecture).
Reviewed by: imp
it had no hooks. It has abused ifnet's if_afdata slot and actually
abused every subsystem it touched.
lagg(4) is a proper trunking solution at ifnet(9) layer.
ng_one2many(4) is a proper trunking solution in netgraph(4).
Add a SYSINIT that forces a reseed during proc0 setup, which happens
fairly late in the boot process.
Add a RANDOM_DEBUG option which enables some debugging printf()s.
Add a new RANDOM_ATTACH entropy source which harvests entropy from the
get_cyclecount() delta across each call to a device attach method.
Update the OFED Infiniband core to the version supplied in Linux
version 3.7.
The update to OFED is nearly all additional defines and functions
with the exception of the addition of additional parameters to
ib_register_device() and the reg_user_mr callback.
In addition the ibcore (Infiniband core) and ipoib (IP over Infiniband)
have both been made into completely loadable modules to facilitate
testing of the OFED stack in FreeBSD.
Finally the Mellanox Infiniband drivers are now updated to the
latest version shipping with Linux 3.7.
Submitted by: Mellanox FreeBSD driver team:
Oded Shanoon (odeds mellanox.com),
Meny Yossefi (menyy mellanox.com),
Orit Moskovich (oritm mellanox.com)
Approved by: re
to implement epoll subset of functionality. The kqueue user data are 32bit
on i386 which is not enough for epoll user data so this patch overrides
kqueue fileops to maintain enough space in struct file.
Initial patch developed by me in 2007 and then extended and finished
by Yuri Victorovich.
Approved by: re (delphij)
Sponsored by: Google Summer of Code
Submitted by: Yuri Victorovich <yuri at rawbw dot com>
Tested by: Yuri Victorovich <yuri at rawbw dot com>
and the equivalent functionality is now provided by sendfile(2) over
posix shared memory filedescriptor.
Remove the cow member of struct vm_page, and rearrange the remaining
members. While there, make hold_count unsigned.
Requested and reviewed by: alc
Tested by: pho
Sponsored by: The FreeBSD Foundation
Approved by: re (delphij)
performance... Use SSE2 instructions for calculating the XTS tweek
factor... Let the compiler do more work and handle register allocation
by using intrinsics, now only the key schedule is in assembly...
Replace .byte hard coded instructions w/ the proper instructions now
that both clang and gcc support them...
On my machine, pulling the code to userland I saw performance go from
~150MB/sec to 2GB/sec in XTS mode. GELI on GNOP saw a more modest
increase of about 3x due to other system overhead (geom and
opencrypto)...
These changes allow almost full disk io rate w/ geli...
Reviewed by: -current, -security
Thanks to: Mike Hamburg for the XTS tweek algorithm
This is a significant rewrite of much of the previous driver; lots of
misc. cleanup was also performed, and support for a few other minor
features was also added.
This driver is based on Linux 3.8 and a previous effort by kan@.
More informations about this project can be found on the FreeBSD wiki:
https://wiki.freebsd.org/AMD_GPU
The driver is split into:
sys/dev/drm2:
The driver sources.
sys/modules/drm2/radeonkmw:
The driver main kernel module's Makefile.
sys/modules/drm2/radeonkmsfw:
All firmware kernel module Makefiles. There's one directory and one
Makefile for each firmware.
sys/contrib/dev/drm2/radeonkmsfw:
All firmware binary sources.
tools/tools/drm/radeon
Tools to update firmwares or regenerate some headers.
Merging the driver to FreeBSD 9.x may be possible but not a priority for
now.
Help from: kib@, kan@
Tested by: avg@, kwm@, ray@,
Alexander Yerenkow <yerenkow@gmail.com>,
Anders Bolt-Evensen <andersbo87@me.com>,
Denis Djubajlo <stdedjub@googlemail.com>,
J.R. Oldroyd <fbsd@opal.com>,
Mikaël Urankar <mikael.urankar@gmail.com>,
Pierre-Emmanuel Pédron <pepcitron@gmail.com>,
Sam Fourman Jr. <sfourman@gmail.com>,
Wade <wade-is-great@live.com>,
(probably other I forgot...)
HW donations: kyzh, Yakaz
* It's not meant to be used in a real system, it's there to show how
the basics of how to create interfaces for random_adaptors. Perhaps
it should belong in a manual page
2) Move probe.c's functionality in to random_adaptors.c
* rename random_ident_hardware() to random_adaptor_choose()
3) Introduce a new way to choose (or select) random_adaptors via tunable
"rngs_want" It's a list of comma separated names of adaptors, ordered
by preferences. I.e.:
rngs_want="yarrow,rdrand"
Such setting would cause yarrow to be preferred to rdrand. If neither of
them are available (or registered), then system will default to
something reasonable (currently yarrow). If yarrow is not present, then
we fall back to the adaptor that's first on the list of registered
adaptors.
4) Introduce a way where RNGs can play a role of entropy source. This is
mostly useful for HW rngs.
The way I envision this is that every HW RNG will use this
functionality by default. Functionality to disable this is also present.
I have an example of how to use this in random_adaptor_example.c (see
modload event, and init function)
5) fix kern.random.adaptors from
kern.random.adaptors: yarrowpanicblock
to
kern.random.adaptors: yarrow,panic,block
6) add kern.random.active_adaptor to indicate currently selected
adaptor:
root@freebsd04:~ # sysctl kern.random.active_adaptor
kern.random.active_adaptor: yarrow
Submitted by: Arthur Mesh <arthurmesh@gmail.com>
the build while here. sys/ofed has more recent RDMA code and should be
used instead. We should probably move krping out of sys/contrib/rdma
and get rid of the rest of it.
Obtained from: Chelsio
(sys/dev/iscsi_initiator/ instead of sys/dev/iscsi/initiator/), to make
room for the new one. This is also more logical location (kernel module
being named iscsi_initiator.ko, for example). There is no ongoing work
on this I know of, so it shouldn't make life harder for anyone.
There are no functional changes, apart from "svn mv" and adjusting paths.
Basic support for extents was implemented by Zheng Liu as part
of his Google Summer of Code in 2010. This support is read-only
at this time.
In addition to extents we also support the huge_file extension
for read-only purposes. This works nicely with the additional
support for birthtime/nanosec timestamps and dir_index that
have been added lately.
The implementation may not work for all ext4 filesystems as
it doesn't support some features that are being enabled by
default on recent linux like flex_bg. Nevertheless, the feature
should be very useful for migration or simple access in
filesystems that have been converted from ext2/3 or don't use
incompatible features.
Special thanks to Zheng Liu for his dedication and continued
work to support ext2 in FreeBSD.
Submitted by: Zheng Liu (lz@)
Reviewed by: Mike Ma, Christoph Mallon (previous version)
Sponsored by: Google Inc.
MFC after: 3 weeks
Do this by forcing inclusion of
sys/cddl/compat/opensolaris/sys/debug_compat.h
via -include option into all source files from OpenSolaris.
Note that this -include option must always be after -include opt_global.h.
Additionally, remove forced definition of DEBUG for some modules and fix
their build without DEBUG.
Also, meaning of DEBUG was overloaded to enable WITNESS support for some
OpenSolaris (primarily ZFS) locks. Now this overloading is removed and
that use of DEBUG is replaced with a new option OPENSOLARIS_WITNESS.
MFC after: 17 days
- change the SI_SUB_RUN_SCHEDULER sysinits in hv_utilc and
hv_netvsc_drv_freebsd.c to SI_SUB_KTHREAD_IDLE, since the
former is no longer in FreeBSD.
The use of these SYSINITs can probably be removed.
Support chipsets are the Realtek RTL8188SU, RTL8191SU, and RTL8192SU.
Many thanks to Idwer Vollering for porting/writing the man page and for
testing.
Reviewed by: adrian, hselasky
Obtained from: OpenBSD
Tested by: kevlo, Idwer Vollering <vidwer at gmail.com>
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.
* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.
* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah
* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.
* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.
* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.
Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien
all T4 and T5 based cards and is useful for analyzing TSO, LRO, TOE, and
for general purpose monitoring without tapping any cxgbe or cxl ifnet
directly.
Tracers on the T4/T5 chips provide access to Ethernet frames exactly as
they were received from or transmitted on the wire. On transmit, a
tracer will capture a frame after TSO segmentation, hw VLAN tag
insertion, hw L3 & L4 checksum insertion, etc. It will also capture
frames generated by the TCP offload engine (TOE traffic is normally
invisible to the kernel). On receive, a tracer will capture a frame
before hw VLAN extraction, runt filtering, other badness filtering,
before the steering/drop/L2-rewrite filters or the TOE have had a go at
it, and of course before sw LRO in the driver.
There are 4 tracers on a chip. A tracer can trace only in one direction
(tx or rx). For now cxgbetool will set up tracers to capture the first
128B of every transmitted or received frame on a given port. This is a
small subset of what the hardware can do. A pseudo ifnet with the same
name as the nexus driver (t4nex0 or t5nex0) will be created for tracing.
The data delivered to this ifnet is an additional copy made inside the
chip. Normal delivery to cxgbe<n> or cxl<n> will be made as usual.
/* watch cxl0, which is the first port hanging off t5nex0. */
# cxgbetool t5nex0 tracer 0 tx0 (watch what cxl0 is transmitting)
# cxgbetool t5nex0 tracer 1 rx0 (watch what cxl0 is receiving)
# cxgbetool t5nex0 tracer list
# tcpdump -i t5nex0 <== all that cxl0 sees and puts on the wire
If you were doing TSO, a tcpdump on cxl0 may have shown you ~64K
"frames" with no L3/L4 checksum but this will show you the frames that
were actually transmitted.
/* all done */
# cxgbetool t5nex0 tracer 0 disable
# cxgbetool t5nex0 tracer 1 disable
# cxgbetool t5nex0 tracer list
# ifconfig t5nex0 destroy
USB mouse and USB modem classes. Hopefully someone will find
these examples useful when implementing USB device side drivers
using the FreeBSD USB stack.
As part of this commit, add an nvme_strvis() function which borrows
heavily from cam_strvis(). This will allow stripping of
leading/trailing whitespace and also handle unprintable characters
in model/serial numbers. This function goes into a new nvme_util.c
file which is used by both the driver and nvmecontrol.
Sponsored by: Intel
Reviewed by: carl
MFC after: 3 days
be pulled into FreeBSD. From now, FreeBSD will be considered the
upstream repo.
First step: move the drivers away from the contrib area and into
the base system.
A follow-on commit will include the drivers in the amd64 GENERIC kernel.
ixgbe driver. As it was, when building them as a module INET
and INET6 are not defined. In these drivers it does not cause
a panic, however it does result in different behavior in the
ioctl routine when you are using a module vs static, and I
think the behavior should be the same.
MFC after: 3 days
This is a port of NetBSD's GSoC 2012 Ext3 HTree directory indexing
by Vyacheslav Matyushin. It was cleaned up and enhanced for FreeBSD
by Zheng Liu (lz@).
This is an excellent example of work shared among different projects:
Vyacheslav was able to look at an early prototype from Zheng Liu who
was also able to check the code from Haiku (with permission).
As in linux, the feature is not available by default and must be
enabled explicitly with tune2fs. We still do not support the
workarounds required in readdir for NFS.
Submitted by: Zheng Liu
Tested by: Mike Ma
Sponsored by: Google Inc.
MFC after: 1 week
algorithm, which is based on the 2011 v0.1 patch release and described in the
paper "Revisiting TCP Congestion Control using Delay Gradients" by David Hayes
and Grenville Armitage. It is implemented as a kernel module compatible with the
modular congestion control framework.
CDG is a hybrid congestion control algorithm which reacts to both packet loss
and inferred queuing delay. It attempts to operate as a delay-based algorithm
where possible, but utilises heuristics to detect loss-based TCP cross traffic
and will compete effectively as required. CDG is therefore incrementally
deployable and suitable for use on shared networks.
In collaboration with: David Hayes <david.hayes at ieee.org> and
Grenville Armitage <garmitage at swin edu au>
MFC after: 4 days
Sponsored by: Cisco University Research Program and FreeBSD Foundation
- Reconnect with some minor modifications, in particular now selsocket()
internals are adapted to use sbintime units after recent'ish calloutng
switch.
same as top-level target name for "device runfw" kernel option and
caused cyclic dependancy that lead to kernel build breakage
Module change is not strictly required and done for name unification sake
PR: conf/175751
Submitted by: Issei <i10a at herbmint.jp>
(which should be a PCIE Gen 3 slot for this adapter) by looking back thru the PCI
parent devices to the slot device.
The fix above also corrects the bandwidth display to GT/s rather than the
incorrect Gb/s
Next, allow the use of ALTQ if you select the compile option IXGBE_LEGACY_TX.
Allow the use of 'unsupported' optic modules by a compile option as well.
Add a phy reset capability into the stop code, this is so a static configured
driver will still behave properly when taken down (not being able to unload it).
This revision synchronizes the shared code with Intel internal current code,
and note that it now includes DCB supporting code, this was necessitated by
some internal changes with the code, but it also will provide the opportunity
to develop this feature in the core driver down the road.
I have edited the README to get rid of some of the worse anachronisms in it
as well, its by no means as robust as I might wish at this point however.
Oh, I also have included some conditional stuff in the code so it will be
compatible in both the 9.X and 10 environments.
Performance has been a focus in recent changes and I believe this revision
driver will perform very well in most workloads.
MFC after: 2 weeks
The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.
This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.
Tested:
* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM
Realtek RTL8188CU/RTL8192CU USB IEEE 802.11b/g/n wireless cards.
This driver requires microcode which is available in FreeBSD ports:
net/urtwn-firmware-kmod.
Hiren ported the urtwn(4) man page from OpenBSD and Glen just commited a port
for the firmware.
TODO:
- 802.11n support
- Stability fixes - the driver can sustain lots of traffic but has trouble
coping with simultaneous iperf sessions.
- fix debugging
MFC after: 2 months
Tested by: kevlo, hiren, gjb
for the WB195 combo NIC - an AR9285 w/ an AR3011 USB bluetooth NIC.
The AR3011 is wired up using a 3-wire coexistence scheme to the AR9285.
The code in if_ath_btcoex.c sets up the initial hardware mapping
and coexistence configuration. There's nothing special about it -
it's static; it doesn't try to configure bluetooth / MAC traffic priorities
or try to figure out what's actually going on. It's enough to stop basic
bluetooth traffic from causing traffic stalls and diassociation from
the wireless network.
To use this code, you must have the above NIC. No, it won't work
for the AR9287+AR3012, nor the AR9485, AR9462 or AR955x combo cards.
Then you set a kernel hint before boot or before kldload, where 'X'
is the unit number of your AR9285 NIC:
# kenv hint.ath.X.btcoex_profile=wb195
This will then appear in your boot messages:
[100482] athX: Enabling WB195 BTCOEX
This code is going to evolve pretty quickly (well, depending upon my
spare time) so don't assume the btcoex API is going to stay stable.
In order to use the bluetooth side, you must also load in firmware using
ath3kfw and the binary firmware file (ath3k-1.fw in my case.)
Tested:
* AR9280, no interference
* WB195 - AR9285 + AR3011 combo; STA mode; basic bluetooth inquiries
were enough to cause traffic stalls and disassociations. This has
stopped with the btcoex profile code.
TODO:
* Importantly - the AR9285 needs ASPM disabled if bluetooth coexistence
is enabled. No, I don't know why. It's likely some kind of bug to do
with the AR3011 sending bluetooth coexistence signals whilst the device
is asleep. Since we don't actually sleep the MAC just yet, it shouldn't
be a problem. That said, to be totally correct:
+ ASPM should be disabled - upon attach and wakeup
+ The PCIe powersave HAL code should never be called
Look at what the ath9k driver does for inspiration.
* Add WB197 (AR9287+AR3012) support
* Add support for the AR9485, which is another combo like the AR9285
* The later NICs have a different signaling mechanism between the MAC
and the bluetooth device; I haven't even begun to experiment with
making that HAL code work. But it should be a lot more automatic.
* The hardware can do much more interesting traffic weighting with
bluetooth and wifi traffic. None of this is currently used.
Ideally someone would code up something to watch the bluetooth traffic
GPIO (via an interrupt) and then watch it go high/low; then figure out
what the bluetooth traffic is and adjust things appropriately.
* If I get the time I may add in some code to at least track this stuff
and expose statistics. But it's up to someone else to experiment with
the bluetooth coexistence support and add the interesting stuff (like
"real" detection of bulk, audio, etc bluetooth traffic patterns and
change wifi parameters appropriately - eg, maximum aggregate length,
transmit power, using quiet time to control TX duty cycle, etc.)
seven arguments.
The original test uses Solaris' uadmin system call to trigger the test
probe; this change adds a sysctl to the dtrace_test module and gets the test
program to trigger the test probe via the sysctl handler.
The test is currently failing on amd64 because of some bugs in the way that
probe arguments beyond the first five are obtained - these bugs will be
fixed in a separate change.
QLogic 8300 Series Adapters
Submitted by: David C Somayajulu (davidcs@freebsd.org) QLogic Corporation
Approved by: George Neville-Neil (gnn@freebsd.org)
The NTB allows you to connect two systems with this device using a PCI-e
link. The driver is made of two modules:
- ntb_hw which is a basic hardware abstraction layer for the device.
- if_ntb which implements the ntb network device and the communication
protocol.
The driver is limited at the moment to CPU memcpy instead of using DMA, and
only Back-to-Back mode is supported. Also the network device isn't full
featured yet. These changes will be coming soon. The DMA change will also
bring in the ioat driver from the project branch it is on now.
This is an initial port of the GPL/BSD Linux driver contributed by Jon Mason
from Intel. Any bugs are my contributions.
Sponsored by: Intel
Reviewed by: jimharris, joel (man page only)
Approved by: jimharris (mentor)
it will work with either the old or new server.
The FHA code keeps a cache of currently active file handles for
NFSv2 and v3 requests, so that read and write requests for the same
file are directed to the same group of threads (reads) or thread
(writes). It does not currently work for NFSv4 requests. They are
more complex, and will take more work to support.
This improves read-ahead performance, especially with ZFS, if the
FHA tuning parameters are configured appropriately. Without the
FHA code, concurrent reads that are part of a sequential read from
a file will be directed to separate NFS threads. This has the
effect of confusing the ZFS zfetch (prefetch) code and makes
sequential reads significantly slower with clients like Linux that
do a lot of prefetching.
The FHA code has also been updated to direct write requests to nearby
file offsets to the same thread in the same way it batches reads,
and the FHA code will now also send writes to multiple threads when
needed.
This improves sequential write performance in ZFS, because writes
to a file are now more ordered. Since NFS writes (generally
less than 64K) are smaller than the typical ZFS record size
(usually 128K), out of order NFS writes to the same block can
trigger a read in ZFS. Sending them down the same thread increases
the odds of their being in order.
In order for multiple write threads per file in the FHA code to be
useful, writes in the NFS server have been changed to use a LK_SHARED
vnode lock, and upgrade that to LK_EXCLUSIVE if the filesystem
doesn't allow multiple writers to a file at once. ZFS is currently
the only filesystem that allows multiple writers to a file, because
it has internal file range locking. This change does not affect the
NFSv4 code.
This improves random write performance to a single file in ZFS, since
we can now have multiple writers inside ZFS at one time.
I have changed the default tuning parameters to a 22 bit (4MB)
window size (from 256K) and unlimited commands per thread as a
result of my benchmarking with ZFS.
The FHA code has been updated to allow configuring the tuning
parameters from loader tunable variables in addition to sysctl
variables. The read offset window calculation has been slightly
modified as well. Instead of having separate bins, each file
handle has a rolling window of bin_shift size. This minimizes
glitches in throughput when shifting from one bin to another.
sys/conf/files:
Add nfs_fha_new.c and nfs_fha_old.c. Compile nfs_fha.c
when either the old or the new NFS server is built.
sys/fs/nfs/nfsport.h,
sys/fs/nfs/nfs_commonport.c:
Bring in changes from Rick Macklem to newnfs_realign that
allow it to operate in blocking (M_WAITOK) or non-blocking
(M_NOWAIT) mode.
sys/fs/nfs/nfs_commonsubs.c,
sys/fs/nfs/nfs_var.h:
Bring in a change from Rick Macklem to allow telling
nfsm_dissect() whether or not to wait for mallocs.
sys/fs/nfs/nfsm_subs.h:
Bring in changes from Rick Macklem to create a new
nfsm_dissect_nonblock() inline function and
NFSM_DISSECT_NONBLOCK() macro.
sys/fs/nfs/nfs_commonkrpc.c,
sys/fs/nfsclient/nfs_clkrpc.c:
Add the malloc wait flag to a newnfs_realign() call.
sys/fs/nfsserver/nfs_nfsdkrpc.c:
Setup the new NFS server's RPC thread pool so that it will
call the FHA code.
Add the malloc flag argument to newnfs_realign().
Unstaticize newnfs_nfsv3_procid[] so that we can use it in
the FHA code.
sys/fs/nfsserver/nfs_nfsdsocket.c:
In nfsrvd_dorpc(), add NFSPROC_WRITE to the list of RPC types
that use the LK_SHARED lock type.
sys/fs/nfsserver/nfs_nfsdport.c:
In nfsd_fhtovp(), if we're starting a write, check to see
whether the underlying filesystem supports shared writes.
If not, upgrade the lock type from LK_SHARED to LK_EXCLUSIVE.
sys/nfsserver/nfs_fha.c:
Remove all code that is specific to the NFS server
implementation. Anything that is server-specific is now
accessed through a callback supplied by that server's FHA
shim in the new softc.
There are now separate sysctls and tunables for the FHA
implementations for the old and new NFS servers. The new
NFS server has its tunables under vfs.nfsd.fha, the old
NFS server's tunables are under vfs.nfsrv.fha as before.
In fha_extract_info(), use callouts for all server-specific
code. Getting file handles and offsets is now done in the
individual server's shim module.
In fha_hash_entry_choose_thread(), change the way we decide
whether two reads are in proximity to each other.
Previously, the calculation was a simple shift operation to
see whether the offsets were in the same power of 2 bucket.
The issue was that there would be a bucket (and therefore
thread) transition, even if the reads were in close
proximity. When there is a thread transition, reads wind
up going somewhat out of order, and ZFS gets confused.
The new calculation simply tries to see whether the offsets
are within 1 << bin_shift of each other. If they are, the
reads will be sent to the same thread.
The effect of this change is that for sequential reads, if
the client doesn't exceed the max_reqs_per_nfsd parameter
and the bin_shift is set to a reasonable value (22, or
4MB works well in my tests), the reads in any sequential
stream will largely be confined to a single thread.
Change fha_assign() so that it takes a softc argument. It
is now called from the individual server's shim code, which
will pass in the softc.
Change fhe_stats_sysctl() so that it takes a softc
parameter. It is now called from the individual server's
shim code. Add the current offset to the list of things
printed out about each active thread.
Change the num_reads and num_writes counters in the
fha_hash_entry structure to 32-bit values, and rename them
num_rw and num_exclusive, respectively, to reflect their
changed usage.
Add an enable sysctl and tunable that allows the user to
disable the FHA code (when vfs.XXX.fha.enable = 0). This
is useful for before/after performance comparisons.
nfs_fha.h:
Move most structure definitions out of nfs_fha.c and into
the header file, so that the individual server shims can
see them.
Change the default bin_shift to 22 (4MB) instead of 18
(256K). Allow unlimited commands per thread.
sys/nfsserver/nfs_fha_old.c,
sys/nfsserver/nfs_fha_old.h,
sys/fs/nfsserver/nfs_fha_new.c,
sys/fs/nfsserver/nfs_fha_new.h:
Add shims for the old and new NFS servers to interface with
the FHA code, and callbacks for the
The shims contain all of the code and definitions that are
specific to the NFS servers.
They setup the server-specific callbacks and set the server
name for the sysctl and loader tunable variables.
sys/nfsserver/nfs_srvkrpc.c:
Configure the RPC code to call fhaold_assign() instead of
fha_assign().
sys/modules/nfsd/Makefile:
Add nfs_fha.c and nfs_fha_new.c.
sys/modules/nfsserver/Makefile:
Add nfs_fha_old.c.
Reviewed by: rmacklem
Sponsored by: Spectra Logic
MFC after: 2 weeks
and kern.cam.ctl.disable tunable; those were introduced as a workaround
to make it possible to boot GENERIC on low memory machines.
With ctl(4) being built as a module and automatically loaded by ctladm(8),
this makes CTL work out of the box.
Reviewed by: ken
Sponsored by: FreeBSD Foundation
option left but actually consumed by ada(4), so move it to opt_ada.h
and get rid of opt_ata.h.
- Fix stand-alone build of atacore(4) by adding opt_cam.h.
- Use __FBSDID.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Move ata_timeout() to ata-all.c so we don't need to expose both this
function and ata_cam_end_transaction() but only the former.
- Move ata_cmd2str() from ata-queue.c to ata-all.c so we can get rid of
the former.
- Add some missing prototypes.
MFC after: 3 days
most kernels before FreeBSD 9.0. Remove such modules and respective kernel
options: atadisk, ataraid, atapicd, atapifd, atapist, atapicam. Remove the
atacontrol utility and some man pages. Remove useless now options ATA_CAM.
No objections: current@, stable@
MFC after: never
Merge change from illumos:
1368 enablings on defunct providers prevent providers from unregistering
We try to address some underlying differences between the Solaris
and FreeBSD implementations: dtrace_attach() / dtrace_detach() are
currently unimplemented in FreeBSD but the new code from illumos
makes use of taskq so some adaptations were made to dtrace_open()
and dtrace_close() to handle them appropriately.
Illumos Revision: r13430:8e6add739e38
Reference:
https://www.illumos.org/issues/1368
Reviewed by: gnn
Tested by: Fabian Keil
Obtained from: Illumos
MFC after: 3 weeks
includes support for the NIC and TOE features of the 40G, 10G, and
1G/100M cards based on the T5.
The ASIC is mostly backward compatible with the Terminator 4 so cxgbe(4)
has been updated instead of writing a brand new driver. T5 cards will
show up as cxl (short for cxlgb) ports attached to the t5nex bus driver.
Sponsored by: Chelsio
the older if_start/non-multiqueue interface from the stack. This
is not the default, but can be turned on in the Makefile now regardless
of the OS level to allow either testing or use of ALTQ.
MFC after: one week
much of which is not necessary for PowerPC.
The FBT module can likely be factored into 3 separate files: common,
intel, and powerpc, rather than duplicating most of the code between
the x86 and PowerPC flavors.
All DTrace modules for PowerPC will be MFC'd together once Fasttrap is
completed.
future further optimizations where the vm_object lock will be held
in read mode most of the time the page cache resident pool of pages
are accessed for reading purposes.
The change is mostly mechanical but few notes are reported:
* The KPI changes as follow:
- VM_OBJECT_LOCK() -> VM_OBJECT_WLOCK()
- VM_OBJECT_TRYLOCK() -> VM_OBJECT_TRYWLOCK()
- VM_OBJECT_UNLOCK() -> VM_OBJECT_WUNLOCK()
- VM_OBJECT_LOCK_ASSERT(MA_OWNED) -> VM_OBJECT_ASSERT_WLOCKED()
(in order to avoid visibility of implementation details)
- The read-mode operations are added:
VM_OBJECT_RLOCK(), VM_OBJECT_TRYRLOCK(), VM_OBJECT_RUNLOCK(),
VM_OBJECT_ASSERT_RLOCKED(), VM_OBJECT_ASSERT_LOCKED()
* The vm/vm_pager.h namespace pollution avoidance (forcing requiring
sys/mutex.h in consumers directly to cater its inlining functions
using VM_OBJECT_LOCK()) imposes that all the vm/vm_pager.h
consumers now must include also sys/rwlock.h.
* zfs requires a quite convoluted fix to include FreeBSD rwlocks into
the compat layer because the name clash between FreeBSD and solaris
versions must be avoided.
At this purpose zfs redefines the vm_object locking functions
directly, isolating the FreeBSD components in specific compat stubs.
The KPI results heavilly broken by this commit. Thirdy part ports must
be updated accordingly (I can think off-hand of VirtualBox, for example).
Sponsored by: EMC / Isilon storage division
Reviewed by: jeff
Reviewed by: pjd (ZFS specific review)
Discussed with: alc
Tested by: pho
The early commit is done to facilitate the off-tree work on the
porting of the Radeon driver.
Sponsored by: The FreeBSD Foundation
Debugged and tested by: dumbbell
MFC after: 1 month
from the tree since few months (please note that the userland bits
were already disconnected since a long time, thus there is no need
to update the OLD* entries).
This is not targeted for MFC.
- Add support for IPv6 rx csum offload
- Finally switch mxge from using its own driver lro, to
using tcp_lro
MFC after: 7 days
Sponsored by: Myricom Inc.
The "blackhole" driver was used in conjunction with bhyve to sequester
pci devices intended for passthru until vmm.ko was loaded. This was
useful at one point because vmm.ko could not be loaded at boot time.
The same functionality can now be achieved by loading vmm.ko via the
loader along with the kernel.
Discussed with: grehan
Obtained from: NetApp
generating binary diffs.
- Constify a few strings used in the driver.
- Style changes to make the driver compile with default clang settings.
Approved by: HighPoint Technologies
MFC after: 3 days
- Add full support for IPv6 addresses.
- Read the size of the L2 table during attach. Do not assume that PCIe
physical function 4 of the card has all of the table to itself.
- Use FNV instead of Jenkins to hash L3 addresses and drop the private
copy of jhash.h from the driver.
MFC after: 1 week
- In sys/ofed/drivers/infiniband/core/cma.c, an enum struct member is
interpreted as an int, so cast it to an int.
- In sys/ofed/drivers/infiniband/core/ud_header.c, initialize the
packet_length variable in ib_ud_header_init(), to prevent undefined
behaviour.
- In sys/ofed/drivers/infiniband/ulp/sdp/sdp_rx.c, call rdma_notify()
with the correct enum type and value.
- In sys/ofed/include/linux/pci.h, change the PCI_DEVICE and PCI_VDEVICE
macros to use C99 struct initializers, so additional members can be
overridden.
Reviewed by: delphij, Garrett Cooper <yanegomi@gmail.com>
MFC after: 1 week
There is one known issue: Some probes will display an error message along the
lines of: "Invalid address (0)"
I tested this with both a simple dtrace probe and dtruss on a few different
binaries on 32-bit. I only compiled 64-bit, did not run it, but I don't expect
problems without the modules loaded. Volunteers are welcome.
MFC after: 1 month
warns about unused variables in this code, so always add -Wno-unused to
the warning flags. Why gcc on x86 *doesn't* warn about this, I will never
know. The code itself should probably be fixed at some point.
GIANT from VFS. In addition, disconnect also netsmb, which is a base
requirement for SMBFS.
In the while SMBFS regular users can use FUSE interface and smbnetfs
port to work with their SMBFS partitions.
Also, there are ongoing efforts by vendor to support in-kernel smbfs,
so there are good chances that it will get relinked once properly locked.
This is not targeted for MFC.
GIANT from VFS. This code is particulary broken and fragile and other
in-kernel implementations around, found in other operating systems,
don't really seem clean and solid enough to be imported at all.
If someone wants to reconsider in-kernel NTFS implementation for
inclusion again, a fair effort for completely fixing and cleaning it
up is expected.
In the while NTFS regular users can use FUSE interface and ntfs-3g
port to work with their NTFS partitions.
This is not targeted for MFC.
GIANT from VFS. In addition, disconnect also netncp, which is a base
requirement for NWFS.
In the possibility of a future maintenance of the code and later
readd to the FreeBSD base, maybe we should think about a better location
for netncp. I'm not entirely sure the / top location is actually right,
however I will let network people to comment on that more specifically.
This is not targeted for MFC.
sdchi encapsulates a generic SD Host Controller logic that relies on
actual hardware driver for register access.
sdhci_pci implements driver for PCI SDHC controllers using new SDHCI
interface
No kernel config modifications are required, but if you load sdhc
as a module you must switch to sdhci_pci instead.
This has been developed during 2 summer of code mandates and being revived
by gnn recently.
The functionality in this commit mirrors entirely content of fusefs-kmod
port, which doesn't need to be installed anymore for -CURRENT setups.
In order to get some sparse technical notes, please refer to:
http://lists.freebsd.org/pipermail/freebsd-fs/2012-March/013876.html
or to the project branch:
svn://svn.freebsd.org/base/projects/fuse/
which also contains granular history of changes happened during port
refinements. This commit does not came from the branch reintegration
itself because it seems svn is not behaving properly for this functionaly
at the moment.
Partly Sponsored by: Google, Summer of Code program 2005, 2011
Originally submitted by: ilya, Csaba Henk <csaba-ml AT creo DOT hu >
In collabouration with: pho
Tested by: flo, gnn, Gustau Perez,
Kevin Oberman <rkoberman AT gmail DOT com>
MFC after: 2 months
The code builds a map of regions that were freed. On every write the
code consults the map and eventually removes ranges that were freed
before, but are now overwritten.
Freed blocks are not TRIMed immediately. There is a tunable that defines
how many txg we should wait with TRIMming freed blocks (64 by default).
There is a low priority thread that TRIMs ranges when the time comes.
During TRIM we keep in-flight ranges on a list to detect colliding
writes - we have to delay writes that collide with in-flight TRIMs in
case something will be reordered and write will reached the disk before
the TRIM. We don't have to do the same for in-flight writes, as
colliding writes just remove ranges to TRIM.
Sponsored by: multiplay.co.uk
This work includes some important fixes and some improvements obtained
from the zfsonlinux project, including TRIMming entire vdevs on pool
create/add/attach and on pool import for spare and cache vdevs.
Obtained from: zfsonlinux
Submitted by: Etienne Dechamps <etienne.dechamps@ovh.net>
reside, and move there ipfw(4) and pf(4).
o Move most modified parts of pf out of contrib.
Actual movements:
sys/contrib/pf/net/*.c -> sys/netpfil/pf/
sys/contrib/pf/net/*.h -> sys/net/
contrib/pf/pfctl/*.c -> sbin/pfctl
contrib/pf/pfctl/*.h -> sbin/pfctl
contrib/pf/pfctl/pfctl.8 -> sbin/pfctl
contrib/pf/pfctl/*.4 -> share/man/man4
contrib/pf/pfctl/*.5 -> share/man/man5
sys/netinet/ipfw -> sys/netpfil/ipfw
The arguable movement is pf/net/*.h -> sys/net. There are
future plans to refactor pf includes, so I decided not to
break things twice.
Not modified bits of pf left in contrib: authpf, ftp-proxy,
tftp-proxy, pflogd.
The ipfw(4) movement is planned to be merged to stable/9,
to make head and stable match.
Discussed with: bz, luigi
generator, found on IvyBridge and supposedly later CPUs, accessible
with RDRAND instruction.
From the Intel whitepapers and articles about Bull Mountain, it seems
that we do not need to perform post-processing of RDRAND results, like
AES-encryption of the data with random IV and keys, which was done for
Padlock. Intel claims that sanitization is performed in hardware.
Make both Padlock and Bull Mountain random generators support code
covered by kernel config options, for the benefit of people who prefer
minimal kernels. Also add the tunables to disable hardware generator
even if detected.
Reviewed by: markm, secteam (simon)
Tested by: bapt, Michael Moll <kvedulv@kvedulv.de>
MFC after: 3 weeks
warnings in sys/gnu/fs/xfs. The only warnings that still need to be
suppressed are those about array bound overruns of flexible array
members in xfs_dir2_{block,sf}.c, which are too expensive (in terms of
cascading code changes) to fix.
MFC after: 1 week
X-MFC-With: r239959
linking it statically into the kernel. With our gcc in base there are
no warnings, so also remove the WERROR= from the module makefile.
Noted by: Eir Nym <eirnym@gmail.com>
MFC after: 1 week
Basically, this is automatic rx zero copy when feasible. TCP payload is
DMA'd directly into the userspace buffer described by the uio submitted
in soreceive by an application.
- Works with sockets that are being handled by the TCP offload engine
of a T4 chip (you need t4_tom.ko module loaded after cxgbe, and an
"ifconfig +toe" on the cxgbe interface).
- Does not require any modification to the application.
- Not enabled by default. Use hw.t4nex.<X>.toe.ddp="1" to enable it.
'encapsulating interface' used with IPsec and has nothing to do with
storage 'enclosure' services.
MFC after: 3 days
Noticed while: debugging why enc(4) is no longer automatically created
subdevice ahciem. Emulate SEMB SES device from AHCI LED interface to expose
it to users in form of ses(4) CAM device. If we ever see AHCI controllers
supporting SES of SAF-TE over I2C as described by specification, they should
fit well into this new picture.
Sponsored by: iXsystems, Inc.
* Introduce TX DMA setup/teardown methods, mirroring what's done in
the RX path.
Although the TX DMA descriptor is setup via ath_desc_alloc() /
ath_desc_free(), there TX status descriptor ring will be allocated
in this path.
* Remove some of the TX EDMA capability probing from the RX path and
push it into the new TX EDMA path.
These probes are most useful when looking into the structures
they provide, which are listed in io.d. For example:
dtrace -n 'io:genunix::start { printf("%d\n", args[0]->bio_bcount); }'
Note that the I/O systems in FreeBSD and Solaris/Illumos are sufficiently
different that there is not a 1:1 mapping from scripts that work
with one to the other.
MFC after: 1 month
shared code update and small changes in core required
Add support for new i210/i211 devices
Improve queue calculation based on mac type
MFC after:5 days
Asus laptops. It is alike to acpi_asus(4), but uses WMI interface instead
of separate ACPI device.
On Asus EeePC T101MT netbook it allows to handle hotkeys and on/off WLAN,
Bluetooth, LCD backlight, camera, cardreader and touchpad.
On Asus UX31A ultrabook it allows to handle hotkeys, on/off WLAN, Bluetooth,
Wireless LED, control keyboard backlight brightness, monitor temperature
and fan speed. LCD brightness control doesn't work now for unknown reason,
possibly requiring some video card initialization.
Sponsored by: iXsystems, Inc.
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
Add TSO6 and LRO/IPv6 support.
Fix the module Makefile to at least properly inlcude opt_inet6.h
and allow builds without INET or INET6.
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
Allow LRO to work on IPv6 as well.
Fix the module Makefile to at least properly inlcude opt_inet6.h
and allow builds without INET or INET6.
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
Revamp the CAM enclosure services driver.
This updated driver uses an in-kernel daemon to track state changes and
publishes physical path location information\for disk elements into the
CAM device database.
Sponsored by: Spectra Logic Corporation
Sponsored by: iXsystems, Inc.
Submitted by: gibbs, will, mav
operations required by GEMified i915.ko. It also attaches to SandyBridge
and IvyBridge CPU northbridges now.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
There's some TX path TDMA code in if_ath_tx.c which should be migrated
out, but first I should likely try and verify/fix/repair the TDMA support
in 9.x and -HEAD.
The NAND Flash environment consists of several distinct components:
- NAND framework (drivers harness for NAND controllers and NAND chips)
- NAND simulator (NANDsim)
- NAND file system (NAND FS)
- Companion tools and utilities
- Documentation (manual pages)
This work is still experimental. Please use with caution.
Obtained from: Semihalf
Supported by: FreeBSD Foundation, Juniper Networks
defined by the SNIA Common RAID Disk Data Format Specification v2.0.
Supports multiple volumes per array and multiple partitions per disk.
Supports standard big-endian and Adaptec's little-endian byte ordering.
Supports all single-layer RAID levels. Dual-layer RAID levels except
RAID10 are not supported now because of GEOM RAID design limitations.
Some work is still to be done, but the present code already manages basic
interoperation with RAID BIOS of the Adaptec 1430SA SATA RAID controller.
MFC after: 1 month
Sponsored by: iXsystems, Inc.
- When switching to 4-bit operation, send a SET_CLR_CARD_DETECT command
to disconnect the card-detect pull-up resistor from the DAT3 line before
sending the SET_BUS_WIDTH command.
- Add the missing "reserved" zero entry to the mantissa table used to
decode various CSD fields. This was causing SD cards to report that they
could run at 30 MHz instead of the maximum 25 MHz mandated in the spec.
o Enhancements:
- At the MMC layer, format various info from the CID into a string that
uniquely identifies the card instance (manufacturer number, serial
number, product name and revision, etc). Export it as an instance
variable.
- At the MMCSD layer, display the formatted card ID string, and also
report the clock speed of the hardware (not the card's max speed), and
the number of bits and number of blocks per transfer. It comes out like
this now:
mmcsd0: 968MB <SD SD01G 8.0 SN 276886905 MFG 08/2008 by 3 SD> at mmc0
22.5MHz/4bit/128-block
o Use DEVMETHOD_END.
o Use NULL instead of 0 for pointers.
PR: 156496
Submitted by: Ian Lepore
MFC after: 1 week
- Mark 'sdp' as requiring 'inet'.
- Always include "opt_inet.h" and "opt_inet6.h" and modify the IB
driver Makefiles to honor WITH/WITHOUT_INET/INET6/_SUPPORT options
to determine what should be enabled during a module build.
- Fix the mlxen(4) driver and the core IB code to compile without
if INET is disabled (including when both INET and INET6 are disabled).
Reviewed by: bz
MFC after: 2 weeks
First cut of new HW support from LSI and merge into FreeBSD.
Supports Drake Skinny and ThunderBolt cards.
MFhead_mfi r227574
Style
MFhead_mfi r227579
Use bus_addr_t instead of uintXX_t.
MFhead_mfi r227580
MSI support
MFhead_mfi r227612
More bus_addr_t and remove "#ifdef __amd64__".
MFhead_mfi r227905
Improved timeout support from Scott.
MFhead_mfi r228108
Make file.
MFhead_mfi r228208
Fixed botched merge of Skinny support and enhanced handling
in call back routine.
MFhead_mfi r228279
Remove superfluous !TAILQ_EMPTY() checks before TAILQ_FOREACH().
MFhead_mfi r228310
Move mfi_decode_evt() to taskqueue.
MFhead_mfi r228320
Implement MFI_DEBUG for 64bit S/G lists.
MFhead_mfi r231988
Restore structure layout by reverting the array header to
use [0] instead of [1].
MFhead_mfi r232412
Put wildcard pattern later in the match table.
MFhead_mfi r232413
Use lower case for hexadecimal numbers to match surrounding
style.
MFhead_mfi r232414
Add more Thunderbolt variants.
MFhead_mfi r232888
Don't act on events prior to boot or when shutting down.
Add hw.mfi.detect_jbod_change to enable or disable acting
on JBOD type of disks being added on insert and removed on
removing. Switch hw.mfi.msi to 1 by default since it works
better on newer cards.
MFhead_mfi r233016
Release driver lock before taking Giant when deleting children.
Use TAILQ_FOREACH_SAFE when items can be deleted. Make code a
little simplier to follow. Fix a couple more style issues.
MFhead_mfi r233620
Update mfi_spare/mfi_array with the actual number of elements
for array_ref and pd. Change these max. #define names to avoid
name space collisions. This will require an update to mfiutil
It avoids mfiutil having to do a magic calculation.
Add a note and #define to state that a "SYSTEM" disk is really
what the firmware calls a "JBOD" drive.
Thanks to the many that helped, LSI for the initial code drop,
mav, delphij, jhb, sbruno that all helped with code and testing.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
sys/dev/mps/mps_sas.c:861:1: error: function 'mpssas_discovery_timeout' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
mpssas_discovery_timeout(void *data)
^
Because the driver is obtained from upstream, we don't want to modify
it; just silence the warning instead, it is harmless.
MFC after: 3 days
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
get rid of testing explicitly for clang (using ${CC:T:Mclang}) in
individual Makefiles.
Instead, use the following extra macros, for use with clang:
- NO_WERROR.clang (disables -Werror)
- NO_WCAST_ALIGN.clang (disables -Wcast-align)
- NO_WFORMAT.clang (disables -Wformat and friends)
- CLANG_NO_IAS (disables integrated assembler)
- CLANG_OPT_SMALL (adds flags for extra small size optimizations)
As a side effect, this enables setting CC/CXX/CPP in src.conf instead of
make.conf! For clang, use the following:
CC=clang
CXX=clang++
CPP=clang-cpp
MFC after: 2 weeks
sys/dev/hpt27xx/osm_bsd.c, since it gets the following warnings:
sys/dev/hpt27xx/osm_bsd.c:1180:25: error: format string is not a string literal (potentially insecure) [-Werror,-Wformat-security]
S_IRUSR | S_IWUSR, driver_name);
^~~~~~~~~~~
@/dev/hpt27xx/hpt27xx_config.h:46:21: note: expanded from:
#define driver_name hpt27xx_driver_name
^~~~~~~~~~~~~~~~~~~
Since 'hpt27xx_driver_name' is a constant string symbol (coming from the
proprietary hpt27xx_lib.o file), there is no security problem.
Because this driver is provided by the vendor, and applying changes
requires re-certification and other bureaucratic exercises, just disable
the warning for now.
MFC after: 1 week
with clang. Also fix a number of warnings uncovered when building with
clang around some implicit enum conversions.
Sponsored by: Intel
Approved by: scottl
kernel modules that include binary-only code.
More fine-grained control is provided via MK_SOURCELESS_HOST (for native code
that runs on host CPU) and MK_SOURCELESS_UCODE (for microcode).
Reviewed by: julian, delphij, freebsd-arch
Approved by: kib (mentor)
MFC after: 2 weeks
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
This involves significant changes to the mps(4) driver, but is not a
complete rewrite.
Some of the changes in this version of the driver:
- Integrated RAID (IR) support.
- Support for WarpDrive controllers.
- Support for SCSI protection information (EEDP).
- Support for TLR (Transport Level Retries), needed for tape drives.
- Improved error recovery code.
- ioctl interface compatible with LSI utilities.
mps.4: Update the mps(4) driver man page somewhat for the driver
changes. The list of supported hardware still needs to be
updated to reflect the full list of supported cards.
conf/files: Add the new driver files.
mps/mpi/*: Updated version of the MPI header files, with a BSD style
copyright.
mps/*: See above for a description of the new driver features.
modules/mps/Makefile:
Add the new mps(4) driver files.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: ken
MFC after: 1 week
versions derived from /usr/ports/audio/oss.
The particular headers used were taken from the
attic/drv/oss_allegro directory and are mostly identical
to the previous files.
The Maestro3 driver is now free from the GPL.
NOTE: due to lack of testers this driver is being
considered for deprecation and removal.
PR: kern/153920
Approved by: jhb (mentor)
MFC after: 2 weeks
is used.
Although the module _builds_, it fails to load because of a missing symbol from
ieee80211_tdma.c.
Specifics:
* Always build ieee80211_tdma.c in the module;
* only compile in the code if IEEE80211_SUPPORT_TDMA is defined.
The USB code as it stands includes the bus glue along _with_ the controller
code. So the ohci/ehci modules actually build the USB controller code and
the PCI bus glue.
It'd be nice to ship separate modules for the PCI glue and the USB
controller (so for example if there were a USB controller hanging off
the internal SoC bus as well as an external PCI device) it could be done.
This is primarily done to save a few bytes here and there on embedded
systems with limited flash space for kernels - a very limited (sub-1MB)
space may be available for the kernel and may only support gzip encoding.
The rootfs can be LZMA compressed.
This is primarily done to save a few bytes here and there on embedded
systems with limited flash space for kernels - a very limited (sub-1MB)
space may be available for the kernel and may only support gzip encoding.
The rootfs can be LZMA compressed.
- Huge old hdac driver was split into three independent pieces: HDA
controller driver (hdac), HDA CODEC driver (hdacc) and HDA sudio function
driver (hdaa).
- Support for multichannel recording was added. Now, as specification
defines, driver checks input associations for pins with sequence numbers
14 and 15, and if found (usually) -- works as before, mixing signals
together. If it doesn't, it configures input association as multichannel.
- Signal tracer was improved to look for cases where several DACs/ADCs in
CODEC can work with the same audio signal. If such case found, driver
registers additional playback/record stream (channel) for the pcm device.
- New controller streams reservation mechanism was implemented. That
allows to have more pcm devices then streams supported by the controller
(usually 4 in each direction). Now it limits only number of simultaneously
transferred audio streams, that is rarely reachable and properly reported
if happens.
- Codec pins and GPIO signals configuration was exported via set of
writable sysctls. Another sysctl dev.hdaa.X.reconfig allows to trigger
driver reconfiguration in run-time.
- Driver now decodes pins location and connector type names. In some cases
it allows to hint user where on the system case connectors, related to the
pcm device, are located. Number of channels supported by pcm device,
reported now (if it is not 2), should also make search easier.
- Added workaround for digital mic on some Asus laptops/netbooks.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
This uses the emuxkireg.h already used in the emu10k1
snd driver. Special thanks go to Alexander Motin as
he was able to find some errors and reverse engineer
some wrong values in the emuxkireg header.
The emu10kx driver is now free from the GPL.
PR: 153901
Tested by: mav, joel
Approved by: jhb (mentor)
MFC after: 2 weeks
This introduces:
* a basic wtap interface
* a HAL, which implements an abstraction layer for implementing
different device behavious;
* A visibility plugin, which allows for control over which nodes
see other nodes (useful for mesh work.)
It doesn't yet implement sta/adhoc/hostap modes but these are quite
feasible to implement.
Monthadar uses it to do 802.11s mesh verification.
The userland tools will be committed in a follow-up commit.
Submitted by: Monthadar Al Jaberi <monthadar@gmail.com>
opt_ah.h file if KERNBUILDDIR isn't defined.
For now, AH_SUPPORT_AR5416 is required, so I'll just fix any
configuration file in /usr/src which is missing this option.
Pointy hat when things do break to: adrian
This brings in the emuxkireg.h from NetBSD (dev/pci) which
is used for the same purpose but is smaller. The emu10k1
is now free from the GPL.
PR: 153901
Obtained from: NetBSD
Approved by: core (mentor implicit)
MFC after: 2 weeks
All of these are harmless, and are in fact used to shut up warnings from
lint.
While here, remove -Wno-missing-prototypes from the xfs module
Makefile, as I could not reproduce those warnings either with gcc or
clang.
MFC after: 1 week
with clang. There are several macros in these files that return values,
and in some cases nothing is done with them, but it is completely
harmless. For some other files, also disable -Wconstant-conversion,
since that triggers a false positive with the DMA_BIT_MASK() macro.
MFC after: 1 week
with clang:
sys/dev/ce/tau32-ddk.c:1228:37: warning: implicit truncation from 'int' to bitfield changes value from 65532 to 8188 [-Wconstant-conversion]
Since this file is obfuscated C, we can never determine (in a sane way,
at least :) if this points to a real problem or not. The driver has
been in the tree for more than five years, so it most likely isn't.
MFC after: 1 week
- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.
- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.
- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).
- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).
- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.
- Code to manage the L2 tables on the chip.
- Updates to cxgbe(4) man page to go with the tunables that have changed.
- Updates to the shared code in common/
- Updates to the driver-firmware interface (now at fw 1.4.16.0)
MFC after: 1 month
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
Tested on Qemu/KVM, VirtualBox, and BHyVe.
Currently built as modules-only on i386/amd64. Man pages not yet hooked
up, pending review.
Submitted by: Bryan Venteicher bryanv at daemoninthecloset dot org
Reviewed by: bz
MFC after: 4 weeks or so
based on Solarflare SFC9000 family controllers. The driver supports jumbo
frames, transmit/receive checksum offload, TCP Segmentation Offload (TSO),
Large Receive Offload (LRO), VLAN checksum offload, VLAN TSO, and Receive Side
Scaling (RSS) using MSI-X interrupts.
This work was sponsored by Solarflare Communications, Inc.
My sincere thanks to Ben Hutchings for doing a lot of the hard work!
Sponsored by: Solarflare Communications, Inc.
MFC after: 3 weeks
results in the HAL being built without HAL debugging/diagnostic support,
the module building process needs to be somehow taught to not build AR5416+
NICs if AH_SUPPORT_AR5416 isn't defined in opt_ah.h .
This implies that users who are building the driver do so with
KERNBUILDDIR set to the compile/CONFIG directory so the various
opt_* sources can be pulled in.
compiled into the kernel.
Do not try to build the module in case of no INET support but
keep #error calls for now in case we would compile it into the
kernel.
This should fix an issue where the module would fail to enable
IPv6 support from the rc framework, but also other INET and INET6
parts being silently compiled out without giving a warning in the
module case.
While here garbage collect unneeded opt_*.h includes.
opt_ipdn.h is not used anywhere but we need to leave the DUMMYNET
entry in options for conditional inclusion in kernel so keep the
file with the same name.
Reported by: pluknet
Reviewed by: plunket, jhb
MFC After: 3 days
Specifically, add support for "Drake Skinny" and "ThunderBolt" LSI
cards.
Initial code was supplied by LSI under BSD license. Several improvements
were done by myself. Such things like making it work in a static kernel,
be able to boot of the RAID, performance improvements. I removed some
fairly complicated code that seemed to directly access the disks under
the firmware. It doesn't seem to be needed and significantly slowed
down the performance of the driver and caused tons of sense errors to
be reported.
This code is being checked in this area so others can help me get it into
shape to commit into the FreeBSD tree. Assistance has been volunteered
by iXsystems.
We might want to re-work the JBOD attachment that creates /dev/mfisyspd?
node for each disk.
Performance is faster then prior cards. It works okay with WITNESS
and INVARIANTS on amd64 and i386. I recall seeing a use after
free time bug with FreeBSD 8 and a Drake Skinny card with WITNESS
and INVARIANTS on.
First task is get all of the new structures to be named in FreeBSD
style format.
Next is probably to deal with the 64bit addressing changes that are
mostly around the #ifdef __amd64__ checks.
Thanks to LSI for providing the initial code.
Obtained from: LSI
replace amd(4) with the former in the amd64, i386 and pc98 GENERIC kernel
configuration files. Besides duplicating functionality, amd(4), which
previously also supported the AMD Am53C974, unlike esp(4) is no longer
maintained and has accumulated enough bit rot over time to always cause
a panic during boot as long as at least one target is attached to it
(see PR 124667).
PR: 124667
Obtained from: NetBSD (based on)
MFC after: 3 days
take advantage of it instead of duplicating it. This reduces the size of
the i386 GENERIC kernel by about 4k. The only potential in-tree user left
unconverted is xe(4), which generally should be changed to use miibus(4)
instead of implementing PHY handling on its own, as otherwise it makes not
much sense to add a dependency on miibus(4)/mii_bitbang(4) to xe(4) just
for the MII bitbang'ing code. The common MII bitbang'ing code also is
useful in the embedded space for using GPIO pins to implement MII access.
- Based on lessons learnt with dc(4) (see r185750), add bus barriers to the
MII bitbang read and write functions of the other drivers converted in
order to ensure the intended ordering. Given that register access via an
index register as well as register bank/window switching is subject to the
same problem, also add bus barriers to the respective functions of smc(4),
tl(4) and xl(4).
- Sprinkle some const.
Thanks to the following testers:
Andrew Bliznak (nge(4)), nwhitehorn@ (bm(4)), yongari@ (sis(4) and ste(4))
Thanks to Hans-Joerg Sirtl for supplying hardware to test stge(4).
Reviewed by: yongari (subset of drivers)
Obtained from: NetBSD (partially)
drivers that only ever attach to a particular MAC driver, i.e. inphy(4),
ruephy(4) and xlphy(4), to the directory where the respective MAC driver
lives and only compile it into the kernel when the latter is also there,
also removing it from miibus.ko and moving it into the module of the
respective MAC driver.
- While at it, rename exphy.c, which comes from NetBSD where the MAC driver
it corresponds to also is named ex(4) instead of xl(4) but that in FreeBSD
actually identifies itself as xlphy(4), and its function names accordingly
for consistency.
- Additionally while at it, fix some minor style issues like whitespace
in the register headers and add multi-inclusion protection to inphyreg.h.
thanks for their contiued support to FreeBSD.
This is version 10.80.00.003 from codeset 10.2.1 [1]
Obtained from: LSI http://kb.lsi.com/Download16574.aspx [1]
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
build it with and without INET/INET6 support.
Submitted by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Tested by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Approved by: re (bz)
MFC after: 2 weeks
options defined in the kernel config. This more closely matches the
behavior of other modules which inherit configuration settings from the
kernel configuration during a kernel + modules build.
Reviewed by: luigi
Approved by: re (kib)
MFC after: 1 week
improvements:
(1) Implement new model in previously missed at91 UART driver
(2) Move BREAK_TO_DEBUGGER and ALT_BREAK_TO_DEBUGGER from opt_comconsole.h
to opt_kdb.h (spotted by np)
(3) Garbage collect now-unused opt_comconsole.h
MFC after: 3 weeks
Approved by: re (bz)
(1) opt_capsicum.h is no longer required in ffs_alloc.c, so remove the
#include.
(2) portalfs depends on opt_capsicum.h, so have the Makefile generate one
if required.
These affect only modules built without a kernel (i.e, not buildkernel,
but yes buildworld if the dubious MODULES_WITH_WORLD is used).
Approved by: re (bz)
Sponsored by: Google Inc
the NFS subsystems use five of the rpcsec_gss/kgssapi entry points,
but since it was not obvious which others might be useful, all
nineteen were included. Basically the nineteen entry points are
set in a structure called rpc_gss_entries and inline functions
defined in sys/rpc/rpcsec_gss.h check for the entry points being
non-NULL and then call them. A default value is returned otherwise.
Requested by rwatson.
Reviewed by: jhb
MFC after: 2 weeks
cloned from the old NFS client, plus additions for NFSv4. A
review of this code is in progress, however it was felt by the
reviewer that it could go in now, before code slush. Any changes
required by the review can be committed as bug fixes later.
This is in no way a complete DFS/radar detection implementation!
It merely creates an abstracted interface which allows for future
development of the DFS radar detection code.
Note: Net80211 already handles the bulk of the DFS machinery,
all we need to do here is figure out that a radar event has occured
and inform it as such. It then drives the DFS state engine for us.
The "null" DFS radar detection module is included by default;
it doesn't require a device line.
This commit:
* Adds a simple abstracted layer for radar detection state -
sys/dev/ath/ath_dfs/;
* Implements a null DFS module which doesn't do anything;
(ie, implements the exact behaviour at the moment);
* Adds hooks to the ath driver to process received radar events
and gives the DFS module a chance to determine whether
a radar has been detected.
Obtained from: Atheros
filters working. (All other filters - switch without L2 info rewrite,
steer, and drop - were already fully-functional).
Some contrived examples of "switch" filters with L2 rewriting:
# cxgbetool t4nex0 iport 0 dport 80 action switch vlan +9 eport 3
Intercept all packets received on physical port 0 with TCP port 80 as
destination, insert a vlan tag with VID 9, and send them out of port 3.
# cxgbetool t4nex0 sip 192.168.1.1/32 ivlan 5 action switch \
vlan =9 smac aa:bb:cc:dd:ee:ff eport 0
Intercept all packets (received on any port) with source IP address
192.168.1.1 and VLAN id 5, rewrite the VLAN id to 9, rewrite source mac
to aa:bb:cc:dd:ee:ff, and send it out of port 0.
MFC after: 1 week
This branch is now considered frozen: future bhyve development will take
place in a branch off -CURRENT.
sys/dev/bvm/bvm_console.c
sys/dev/bvm/bvm_dbg.c
- simple console driver/gdb debug port used for bringup. supported
by user-space bhyve executable
sys/conf/options.amd64
sys/amd64/amd64/minidump_machdep.c
- allow NKPT to be set in the kernel config file
sys/amd64/conf/GENERIC
- mptable config options; bhyve user-space executable creates an mptable
with number of CPUs, and optional vendor extension
- add bvm console/debug
- set NKPT to 512 to allow loading of large RAM disks from the loader
- include kdb/gdb
sys/amd64/amd64/local_apic.c
sys/amd64/amd64/apic_vector.S
sys/amd64/include/specialreg.h
- if x2apic mode available, use MSRs to access the local APIC, otherwise
fall back to 'classic' MMIO mode
sys/amd64/amd64/mp_machdep.c
- support AP spinup on CPU models that don't have real-mode support by
overwriting the real-mode page with a message that supplies the bhyve
user-space executable with enough information to start the AP directly
in 64-bit mode.
sys/amd64/amd64/vm_machdep.c
- insert pause statements into cpu shutdown busy-wait loops
sys/dev/blackhole/blackhole.c
sys/modules/blackhole/Makefile
- boot-time loadable module that claims all PCI bus/slot/funcs specified
in an env var that are to be used for PCI passthrough
sys/amd64/amd64/intr_machdep.c
- allow round-robin assignment of device interrupts to CPUs to be disabled
from the loader
sys/amd64/include/bus.h
- convert string ins/outs instructions to loops of individual in/out since
bhyve doesn't support these yet
sys/kern/subr_bus.c
- if the device was no created with a fixed devclass, then remove it's
association with the devclass it was associated with during probe.
Otherwise, new drivers do not get a chance to probe/attach since the
device will stay married to the first driver that it probed successfully
but failed to attach.
Sponsored by: NetApp, Inc.
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
vmm.ko - kernel module for VT-x, VT-d and hypervisor control
bhyve - user-space sequencer and i/o emulation
vmmctl - dump of hypervisor register state
libvmm - front-end to vmm.ko chardev interface
bhyve was designed and implemented by Neel Natu.
Thanks to the following folk from NetApp who helped to make this available:
Joe CaraDonna
Peter Snyder
Jeff Heller
Sandeep Mann
Steve Miller
Brian Pawlowski
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
- 77115: Implement support for O_DIRECT.
- 98425: Fix a performance issue introduced in 70131 that was causing
reads before writes even when writing full blocks.
- 98658: Rename the BALLOC flags from B_* to BA_* to avoid confusion with
the struct buf B_ flags.
- 100344: Merge the BA_ and IO_ flags so so that they may both be used in
the same flags word. This merger is possible by assigning the IO_ flags
to the low sixteen bits and the BA_ flags the high sixteen bits.
- 105422: Fix a file-rewrite performance case.
- 129545: Implement IO_INVAL in VOP_WRITE() by marking the buffer as
"no cache".
- Readd the DOINGASYNC() macro and use it to control asynchronous writes.
Change i-node updates to honor DOINGASYNC() instead of always being
synchronous.
- Use a PRIV_VFS_RETAINSUGID check instead of checking cr_uid against 0
directly when deciding whether or not to clear suid and sgid bits.
Submitted by: Pedro F. Giffuni giffunip at yahoo
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
Move the files used for a diskless NFS root from sys/nfsclient
to sys/nfs in preparation for them to be used by both NFS
clients. Also, move the declaration of the three global data
structures from sys/nfsclient/nfs_vfsops.c to sys/nfs/nfs_diskless.c
so that they are defined when either client uses them.
Reviewed by: jhb
MFC after: 2 weeks
create reasonably large cache for the keys that is filled when
needed. The previous version was problematic for very large providers
(hundreds of terabytes or serval petabytes). Every terabyte of data
needs around 256kB for keys. Make the default cache limit big enough
to fit all the keys needed for 4TB providers, which will eat at most
1MB of memory.
MFC after: 2 weeks
In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
Add new RAID GEOM class, that is going to replace ataraid(4) in supporting
various BIOS-based software RAIDs. Unlike ataraid(4) this implementation
does not depend on legacy ata(4) subsystem and can be used with any disk
drivers, including new CAM-based ones (ahci(4), siis(4), mvs(4), ata(4)
with `options ATA_CAM`). To make code more readable and extensible, this
implementation follows modular design, including core part and two sets
of modules, implementing support for different metadata formats and RAID
levels.
Support for such popular metadata formats is now implemented:
Intel, JMicron, NVIDIA, Promise (also used by AMD/ATI) and SiliconImage.
Such RAID levels are now supported:
RAID0, RAID1, RAID1E, RAID10, SINGLE, CONCAT.
For any all of these RAID levels and metadata formats this class supports
full cycle of volume operations: reading, writing, creation, deletion,
disk removal and insertion, rebuilding, dirty shutdown detection
and resynchronization, bad sector recovery, faulty disks tracking,
hot-spare disks. For Intel and Promise formats there is support multiple
volumes per disk set.
Look graid(8) manual page for additional details.
Co-authored by: imp
Sponsored by: Cisco Systems, Inc. and iXsystems, Inc.
Add systrace_linux32 and systrace_freebsd32 modules which provide
support for tracing compat system calls in addition to native system
call tracing provided by systrace module.
Provided that all the systrace modules are loaded now you can select
what syscalls to trace in the following manner:
syscall::xxx:yyy - work on all system calls that match the specification
syscall:freebsd:xxx:yyy - only native system calls
syscall:linux32:xxx:yyy - linux32 compat system calls
syscall:freebsd32:xxx:yyy - freebsd32 compat system calls on amd64
PR: kern/152822
Submitted by: Artem Belevich <fbsdlist@src.cx>
Reviewed by: jhb (earlier version)
MFC after: 3 weeks
Linux ath9k.
The ath9k ar9002_hw_init_cal() isn't entirely clear about what
is supposed to be called for what chipsets, so I'm ignoring the
rest of it and just porting the AR9285 init cal path as-is and
leaving the rest alone. Subsequent commits may also tidy up the
Merlin (AR9285) and other chipset support.
Obtained from: Linux ath9k
generally tidy up the TX power programming code.
Enforce that the TX power offset for Merlin is -5 dBm, rather than
any other value programmable in the EEPROM. This requires some
further code to be ported over from ath9k, so until that is done
and tested, fail to attach NICs whose TX power offset isn't -5
dBm.
This improves both legacy and HT transmission on my merlin board.
It allows for stable MCS TX up to MCS15.
Specifics:
* Refactor out a bunch of the TX power calibration code -
setting/obtaining the power detector / gain boundaries,
programming the PDADC
* Take the -5 dBm TX power offset into account on Merlin -
"0" in the per-rate TX power register means -5 dBm, not
0 dBm
* When doing OLC
* Enforce min (0) and max (AR5416_MAX_RATE_POWER) when fiddling
with the TX power, to avoid the TX power values from wrapping
when low.
* Implement the 1 dBm cck power offset when doing OLC
* Implement temperature compensation for 2.4ghz mode when doing OLC
* Implement an AR9280 specific TX power calibration routine which
includes the OLC twiddles, leaving the earlier chipset path
(AR5416, AR9160) alone
Whilst here, use these refactored routines for the AR9285 TX power
calibration/programming code and enforce correct overflow/underflow
handling when fiddling with TX power values.
Obtained from: linux ath9k
