Only drop BULK and INTERRUPT endpoints, to reset the data toggle,
because for other endpoint types this is not critical.
Tested by: ehaupt@
PR: 262882
MFC after: 3 hours
Sponsored by: NVIDIA Networking
Use the drop and enable endpoint context commands to force a reset of
the data toggle for USB 2.0 and USB 3.0 after:
- clear endpoint halt command (when the driver wishes).
- set config command (when the kernel or user-space wants).
- set alternate setting command (only affected endpoints).
Some XHCI HW implementations may not allow the endpoint reset command when
the endpoint context is not in the halted state.
Reported by: Juniper and Gary Jennejohn
MFC after: 1 week
Sponsored by: NVIDIA Networking
EXT_RESOURCES have been introduced in 12-CURRENT and all supported
releases have it enabled in their kernel config.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D33827
The USB controller drivers assume they can cast a NULL pointer to a
struct and find the address of a member. KUBSan complains about this so
replace with the __offsetof and __containerof macros that use either a
builtin function where available, or the same NULL pointer on older
compilers without the builtin.
Reviewers: hselasky
Subscribers: imp
Reviewed by: hselasky
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D33865
The saf1761 OTG support was only for mips targets (BERI?). Retire it.
Sponsored by: Netflix
Reviewed by: brooks
Differential Revision: https://reviews.freebsd.org/D33706
Create a wrapper for newbus to take giant and for busses to take it too.
bus_topo_lock() should be called before interacting with newbus routines
and unlocked with bus_topo_unlock(). If you need the topology lock for
some reason, bus_topo_mtx() will provide that.
Sponsored by: Netflix
Reviewed by: mav
Differential Revision: https://reviews.freebsd.org/D31831
Add support for the "snps,dis_rxdet_inp3_quirk" quirk needed
at least on SolidRun's HoneyComb.
Reviewed by: manu, mw
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D32921
Currently, to support 64-byte contexts, xhci_ctx_[gs]et_le(32|64) take a
pointer to the field within a 32-byte context and, if 64-byte contexts
are in use, compute where the 64-byte context field is and use that
instead by deriving a pointer from the 32-byte field pointer. This is
done by exploiting a combination of 64-byte contexts being the same
layout as their 32-byte counterparts, just with 32 bytes of padding at
the end, and that all individual contexts are either in a device
context or an input context which itself is page-aligned. By masking out
the low 4 bits (which is the offset of the field within the 32-byte
contxt) of the offset within the page, the offset of the invididual
context within the containing device/input context can be determined,
which is itself 32 times the number of preceding contexts. Thus, adding
this value to the pointer again gets 64 times the number of preceding
contexts plus the field offset, which gives the offset of the 64-byte
context plus the field offset, which is the address of the field in the
64-byte context.
However, this involves a fair amount of lying to the compiler when
constructing these intermediate pointers, and is rather difficult to
reason about. In particular, this is problematic for CHERI, where we
compile the kernel with subobject bounds enabled; that is, unless
annotated to opt out (e.g. for C struct inheritance reasons where you
need to be able to downcast, or containerof idioms), a pointer to a
member of a struct is a capability whose bounds only cover that field,
and any attempt to dereference outside those bounds will fault,
protecting against intra-object buffer overflows. Thus the pointer given
to xhci_ctx_[gs]et_le(32|64) is a capability whose bounds only cover the
field in the 32-byte context, and computing the pointer to the 64-byte
context field takes the address out of bounds, resulting in a fault when
later dereferenced.
This can be cleaned up by using a different abstraction. Instead of
doing the 32-byte to 64-byte conversion on access to the field, we can
do the conversion when getting a pointer to the context itself, and
define proper 64-byte versions of contexts in order to let the compiler
do all the necessary arithmetic rather than do it manually ourselves.
This provides a cleaner implementation, works for CHERI and may even be
slightly more performant as it avoids the need to mess with masking
pointers (which cannot in the general case be optimised by compilers to
be reused across accesses to different fields within the same context,
since it does not know that the contexts are over-aligned compared with
the C ABI requirements).
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D32554
Change the probe return value from BUS_PROBE_DEFAULT to BUS_PROBE_GENERIC
given this is the "generic" attach method. This allows individual
drivers using XHCI generic but needing their own intialisation to
gain priority for attaching over the generic implementation.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D32257
PCIe allows for MSI-X BAR to be either dedicated, or MSI-X Table may
be co-located in some functional BAR. In the later case xhci(4) is
unable to allocate active resource for the table because BAR is
already activated.
Handle it by checking for this special case, and not try to alloc
resource if MSI-X BAR is IO.
Reported and tested by: emaste
Reviewed by: emaste, hselasky
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D26913
At least on Orange Pi PC Plus even the host mode does not work without
enabling the phy and setting it to the host mode.
The driver will now parse dr_mode property and will try to configure
itself and the phy accordingly.
OTG mode is not supported yet, so it is treated as the device / peripheral
mode.
The phy is enabled -- powered on -- only for the host mode.
The device mode requires support from a phy driver, e.g., aw_usbphy on
Allwinner platform.
aw_usbphy does not support the device mode, so it cannnot work yet.
MFC after: 6 weeks
Otherwise, I get this panic:
panic: awusbdrd_reg: Invalid register 0x342
It looks that musb code both writes and reads at least MUSB2_REG_TXDBDIS.
MFC after: 5 weeks
X-MFC after: r365399
The "Intel Sunrise Point-LP USB 3.0 controller" doesn't update the wMaxPacket
field in the control endpoint context automatically causing a BABBLE error code
on the initial first USB device descriptor read, when the bMaxPacketSize is not
8 bytes.
Reported by: wulf@
PR: 248784
MFC after: 1 week
Sponsored by: Mellanox Technologies
The AMD's Ryzen 3 3200g XHCI controllers apparently need the evaluate
control endpoint context command, but we don't need to issue this
command when the bMaxPacketSize is received after the read of the USB
device descriptor, because this part should be handled automatically.
PR: 248784
Tested by: emaste, hselasky
MFC after: 1 week
Sponsored by: Mellanox Technologies
The XHCI specification says that the XHCI controller should detect
reception of the USB device descriptors, and automatically update
the max packet size in the control endpoint context.
Differential Revision: https://reviews.freebsd.org/D26104
Reviewed by: kp@
MFC after: 1 week
Sponsored by: Mellanox Technologies
The newer hardware revisions of the Raspberry Pi 4 removed the ability of
the VIA VL805 xhci controller to load its own firmware. Instead the
firmware must be installed at the appropriate time by the VideoCore
coprocessor.
Submitted by: Robert Crowston <crowston_protonmail.com>
Differential Revision: https://reviews.freebsd.org/D25261
Create an acpi attachment for the DWC USB OTG device. This is present in
the Raspberry Pi 4 in the USB-C port normally used to power the board. Some
firmware presents the kernel with ACPI tables rather than FDT so we need
an ACPI attachment.
Submitted by: Greg V <greg_unrelenting.technology>
Approved by: hselasky (removal of All rights reserved)
Differential Revision: https://reviews.freebsd.org/D25203
don't implement link power management, LPM.
This fixes error code XHCI_TRB_ERROR_BANDWIDTH for isochronous USB 3.0
transactions.
Submitted by: Horse Ma <Shichun.Ma@dell.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
A similar fix was done in r333074 but imx_ehci wasn't renamed and generic_ehci wasn't
present at that time.
because it clobbers the super speed link status when a device is in super
speed mode. Currently the power bit is not needed for anything in the USB
hub driver.
This fixes USB warm reset for super speed devices.
Tested by: Shichun.Ma@dell.com
MFC after: 3 days
Sponsored by: Mellanox Technologies
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
This avoids getting the XHCI_TRB_ERROR_CONTEXT_STATE error code from the XHCI
controller when the endpoint is disabled or already stopped.
Suggested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
The newer versions of RPi FDT flipped the order of the interrupts
specification and added an 'interrupt-names' property for driver aide in
finding the correct interrupt, rather than assuming the positions. Use it if
it's available, or fallback to the old method if there is no interrupt-names
property with a usb value.
This has been tested with both old RPi3B FDT and new RPi3B FDT, USB again
works on the latter.
Reported by: Tom Yan <tom.ty89 gmail com>
MFC after: 3 days
Do not configure any endpoint twice, but instead keep track of which
endpoints are configured on a per device basis, and use an evaluate
endpoint context command instead. When changing the configuration make
sure all endpoints get deconfigured and the configured endpoint mask
is reset.
This fixes an issue where an endpoint might stop working if there is
an error and the endpoint needs to be reconfigured as a part of the
error recovery mechanism in the FreeBSD USB stack.
Tested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Create an attachment file for the existing ACPI attachment, and create a
new FDT attachment for the generic-ehci driver.
Submitted by: andrew (Original version)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19389
above 1Kbyte. It might look like some XHCI(4) controllers do not
support when the USB control transfer is split using a link TRB. The
next NORMAL TRB after the link TRB is simply failing with XHCI error
code 4. The quirk ensures we allocate a 64Kbyte buffer so that the
data stage TRB is not broken with a link TRB.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
Ampere eMAG systems have XHCI just described in ACPI, not on PCI.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: andrew
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19986
Marvell XHCI is in fact generic-xhci, so move the driver and
add the compatible string.
While here, get and enable the phy if the dtb provide one.
The xhci bindings state that phys should be in a 'phys' property but
Marvell DTS uses 'usb-phy', only add support for 'usb-phy' for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
This is a "fake" phy that handle regulator, clocks and reset gpio.
Only clock and regulator is supported for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
transaction translator will return a NAK. Ignore this message and
retry the complete split instead.
MFC after: 3 days
Sponsored by: Mellanox Technologies
translator, when using the DWC OTG USB controller driver. Make sure to re-try
getting the complete split packets until a DATA0 packet is received. Larger
isochronous frames may be split into multiple MDATA packets terminated
by a single DATA0 packet.
PR: 230434
MFC after: 3 days
Approved by: re (gjb)
Sponsored by: Mellanox Technologies
The last known robust version of this code base was FreeBSD 8.2. There
are no users of this on current, and all users of it have abandoned
this platform or are in legacy mode with a prior version of FreeBSD.
All known users on arm@ approved this removal, and there were no
objections.
Differential Revision: https://reviews.freebsd.org/D16312
Remove all the big-endian arm architectures (ixp425 and ixp435)
support in the kernel and associated drivers.
Differential Revision: https://reviews.freebsd.org/D16257
doing it last. Also, remove the local tracking of whether usb's busdma
memory allocation got done, because it's safe to call the free_all
function even if it wasn't.
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
endpoints. The Allwinner driver will need to set this as the EPINFO
register isn't useful there.
Submitted by: jmcneill
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D5881
On the Allwinner SoCs we need to set a custom endpoint configuration. To
allow for this use a table to store the configuration so the attachment
can override it.
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14783
would be safe, but the function also tries to destroy mutexes that never
got created).
I guess this can only happen when imx_ehci_detach() is called on the
error-exit path from imx_ehci_attach(), and that path never got exercised
before today.
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
