Other FDT platform (like powerpc64* or riscv64) don't have gpio built
by default so just compile the module for those two arches.
Fixes: 9e08f82058 ("modules: Add sdhci_fdt module")
DXR maintains compressed lookup structures with a trivial search
procedure. A two-stage trie is indexed by the more significant bits of
the search key (IPv4 address), while the remaining bits are used for
finding the next hop in a sorted array. The tradeoff between memory
footprint and search speed depends on the split between the trie and
the remaining binary search. The default of 20 bits of the key being
used for trie indexing yields good performance (see below) with
footprints of around 2.5 Bytes per prefix with current BGP snapshots.
Rebuilding lookup structures takes some time, which is compensated for by
batching several RIB change requests into a single FIB update, i.e. FIB
synchronization with the RIB may be delayed for a fraction of a second.
RIB to FIB synchronization, next-hop table housekeeping, and lockless
lookup capability is provided by the FIB_ALGO infrastructure.
DXR works well on modern CPUs with several MBytes of caches, especially
in VMs, where is outperforms other currently available IPv4 FIB
algorithms by a large margin.
Synthetic single-thread LPM throughput test method:
kldload test_lookup; kldload dpdk_lpm4; kldload fib_dxr
sysctl net.route.test.run_lps_rnd=N
sysctl net.route.test.run_lps_seq=N
where N is the number of randomly generated keys (IPv4 addresses) which
should be chosen so that each test iteration runs for several seconds.
Each reported score represents the best of three runs, in million
lookups per second (MLPS), for two bechmarks (RND & SEQ) with two FIBs:
host: single interface address, local subnet route + default route
BGP: snapshot from linx.routeviews.org, 887957 prefixes, 496 next hops
Bhyve VM on an Intel(R) Xeon(R) CPU E5-2670 0 @ 2.60 GHz:
inet.algo host, RND host, SEQ BGP, RND BGP, SEQ
bsearch4 40.6 20.2 N/A N/A
radix4 7.8 3.8 1.2 0.6
radix4_lockless 18.0 9.0 1.6 0.8
dpdk_lpm4 14.4 5.0 14.6 5.0
dxr 70.3 34.7 43.0 19.5
Intel(R) Core(TM) i5-5300U CPU @ 2.30 GHz:
inet.algo host, RND host, SEQ BGP, RND BGP, SEQ
bsearch4 47.0 23.1 N/A N/A
radix4 8.5 4.2 1.9 1.0
radix4_lockless 19.2 9.5 2.5 1.2
dpdk_lpm4 31.2 9.4 31.6 9.3
dxr 84.9 41.4 51.7 23.6
Intel(R) Core(TM) i7-4771 CPU @ 3.50 GHz:
inet.algo host, RND host, SEQ BGP, RND BGP, SEQ
bsearch4 59.5 29.4 N/A N/A
radix4 10.8 5.5 2.5 1.3
radix4_lockless 24.7 12.0 3.1 1.6
dpdk_lpm4 29.1 9.0 30.2 9.1
dxr 101.3 49.9 69.8 32.5
AMD Ryzen 7 3700X 8-Core Processor @ 3.60 GHz:
inet.algo host, RND host, SEQ BGP, RND BGP, SEQ
bsearch4 70.8 35.4 N/A N/A
radix4 14.4 7.2 2.8 1.4
radix4_lockless 30.2 15.1 3.7 1.8
dpdk_lpm4 29.9 9.0 30.0 8.9
dxr 163.3 81.5 99.5 44.4
AMD Ryzen 5 5600X 6-Core Processor @ 3.70 GHz:
inet.algo host, RND host, SEQ BGP, RND BGP, SEQ
bsearch4 93.6 46.7 N/A N/A
radix4 18.9 9.3 4.3 2.1
radix4_lockless 37.2 18.6 5.3 2.7
dpdk_lpm4 51.8 15.1 51.6 14.9
dxr 218.2 103.3 114.0 49.0
Reviewed by: melifaro
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D29821
Notable upstream pull request merges:
#11742 When specifying raidz vdev name, parity count should match
#11744 Use a helper function to clarify gang block size
#11771 Support running FreeBSD buildworld on Arm-based macOS hosts
This is the last update that will be MFCed into stable/13.
From now on, the tracking of OpenZFS branches will be different:
- main continues tracking openzfs/zfs/master
- stable/13 is going to track openzfs/zfs/zfs-2.1-release
Obtained from: OpenZFS
MFC after: 1 week
Use .o files directly. Replace the .o.uu files that we uudecode with .o files.
Adjust the kernel and module build to cope.
Suggestions by: markj@, emaste@
Sposnored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D29636
uudecode the .o.uu files and commit directly to the tree. Adjust the build
infrastructure to cope with the new location, both for the kernel and modules.
Sposnored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D29635
Store the .o files directly in the tree. We no longer need to play uuencode
games like we did in the CVS days. Adjust the build infrastructure to match.
Reviewed by: markj@
Sposnored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D29634
We no longer need to use uuencode to uuencode files in our tree. Store the .o
file directly instead. Adjust the build to cope with the new arrangement.
Suggestions by: emaste, bz, donner
Reviewed by: markm
Sposnored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D29632
This will make future extensions of the API much easier.
The intent is to remove support for DIOCADDRULE in FreeBSD 14.
Reviewed by: markj (previous version), glebius (previous version)
MFC after: 4 weeks
Sponsored by: Rubicon Communications, LLC ("Netgate")
Differential Revision: https://reviews.freebsd.org/D29557
Currently, AMD-vi PCI-e passthrough will lead to the following lines in
dmesg:
"kernel: CPU0: local APIC error 0x40
ivhd0: Error: completion failed tail:0x720, head:0x0."
After some tracing, the problem is due to the interaction with
amdvi_alloc_intr_resources() and pci_driver_added(). In ivrs_drv, the
identification of AMD-vi IVHD is done by walking over the ACPI IVRS
table and ivhdX device_ts are added under the acpi bus, while there are
no driver handling the corresponding IOMMU PCI function. In
amdvi_alloc_intr_resources(), the MSI intr are allocated with the ivhdX
device_t instead of the IOMMU PCI function device_t. bus_setup_intr() is
called on ivhdX. the IOMMU pci function device_t is only used for
pci_enable_msi(). Since bus_setup_intr() is not called on IOMMU pci
function, the IOMMU PCI function device_t's dinfo->cfg.msi is never
updated to reflect the supposed msi_data and msi_addr. So the msi_data
and msi_addr stay in the value 0. When pci_driver_added() tried to loop
over the children of a pci bus, and do pci_cfg_restore() on each of
them, msi_addr and msi_data with value 0 will be written to the MSI
capability of the IOMMU pci function, thus explaining the errors in
dmesg.
This change includes an amdiommu driver which currently does attaching,
detaching and providing DEVMETHODs for setting up and tearing down
interrupt. The purpose of the driver is to prevent pci_driver_added()
from calling pci_cfg_restore() on the IOMMU PCI function device_t.
The introduction of the amdiommu driver handles allocation of an IRQ
resource within the IOMMU PCI function, so that the dinfo->cfg.msi is
populated.
This has been tested on EPYC Rome 7282 with Radeon 5700XT GPU.
Sponsored by: The FreeBSD Foundation
Reviewed by: jhb
Approved by: philip (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D28984
After length decisions, we've decided that the if_wg(4) driver and
related work is not yet ready to live in the tree. This driver has
larger security implications than many, and thus will be held to
more scrutiny than other drivers.
Please also see the related message sent to the freebsd-hackers@
and freebsd-arch@ lists by Kyle Evans <kevans@FreeBSD.org> on
2021/03/16, with the subject line "Removing WireGuard Support From Base"
for additional context.
This is the culmination of about a week of work from three developers to
fix a number of functional and security issues. This patch consists of
work done by the following folks:
- Jason A. Donenfeld <Jason@zx2c4.com>
- Matt Dunwoodie <ncon@noconroy.net>
- Kyle Evans <kevans@FreeBSD.org>
Notable changes include:
- Packets are now correctly staged for processing once the handshake has
completed, resulting in less packet loss in the interim.
- Various race conditions have been resolved, particularly w.r.t. socket
and packet lifetime (panics)
- Various tests have been added to assure correct functionality and
tooling conformance
- Many security issues have been addressed
- if_wg now maintains jail-friendly semantics: sockets are created in
the interface's home vnet so that it can act as the sole network
connection for a jail
- if_wg no longer fails to remove peer allowed-ips of 0.0.0.0/0
- if_wg now exports via ioctl a format that is future proof and
complete. It is additionally supported by the upstream
wireguard-tools (which we plan to merge in to base soon)
- if_wg now conforms to the WireGuard protocol and is more closely
aligned with security auditing guidelines
Note that the driver has been rebased away from using iflib. iflib
poses a number of challenges for a cloned device trying to operate in a
vnet that are non-trivial to solve and adds complexity to the
implementation for little gain.
The crypto implementation that was previously added to the tree was a
super complex integration of what previously appeared in an old out of
tree Linux module, which has been reduced to crypto.c containing simple
boring reference implementations. This is part of a near-to-mid term
goal to work with FreeBSD kernel crypto folks and take advantage of or
improve accelerated crypto already offered elsewhere.
There's additional test suite effort underway out-of-tree taking
advantage of the aforementioned jail-friendly semantics to test a number
of real-world topologies, based on netns.sh.
Also note that this is still a work in progress; work going further will
be much smaller in nature.
MFC after: 1 month (maybe)
Notable upstream pull request merges:
#11153 Scalable teardown lock for FreeBSD
#11651 Don't bomb out when using keylocation=file://
#11667 zvol: call zil_replaying() during replay
#11683 abd_get_offset_struct() may allocate new abd
#11693 Intentionally allow ZFS_READONLY in zfs_write
#11716 zpool import cachefile improvements
#11720 FreeBSD: Clean up zfsdev_close to match Linux
#11730 FreeBSD: bring back possibility to rewind the
checkpoint from bootloader
Obtained from: OpenZFS
MFC after: 2 weeks
This updates the driver to align with the version included in
the "Intel Ethernet Adapter Complete Driver Pack", version 25.6.
There are no major functional changes; this mostly contains
bug fixes and changes to prepare for new features. This version
of the driver uses the previously committed ice_ddp package
1.3.19.0.
Signed-off-by: Eric Joyner <erj@FreeBSD.org>
Tested by: jeffrey.e.pieper@intel.com
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D28640
Add it to the x86 GENERIC and MINIMAL kernels
Sponsored by: Ampere Computing LLC
Submitted by: Klara Inc.
Reviewed by: rpokala
Differential Revision: https://reviews.freebsd.org/D28738
This package is intended to be used with ice(4) version 0.28.1-k.
That update will happen in a forthcoming commit.
Signed-off-by: Eric Joyner <erj@FreeBSD.org>
Sponsored by: Intel Corporation
Notable upstream changes:
778869fa1 Fix reporting of mount progress
e7adccf7f Disable use of hardware crypto offload drivers on FreeBSD
03e02e5b5 Fix checksum errors not being counted on repeated repair
64e0fe14f Restore FreeBSD resource usage accounting
11f2e9a49 Fix panic if scrubbing after removing a slog device
MFC after: 2 weeks
This uses the chacha20 IETF and poly1305 implementations from
libsodium. A seperate auth_hash is created for the auth side whose
Setkey method derives the poly1305 key from the AEAD key and nonce as
described in RFC 8439.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D27837
Note that this algorithm implements the mode defined in RFC 8439.
Reviewed by: cem
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D27836
AFAICT, this was an oversight from
9e5787d228 (svn r364746). That revision
inadvertently disabled assertions unconditionally.
Reviewed by: freqlabs
MFC after: 3 days
Sponsored by: Axcient
Differential Revision: https://reviews.freebsd.org/D28256
Update zfs_config.h to match latest merge in FreeBSD
The version string is declared as 2.0.0-FreeBSD_gf11b09dec to provide
more information about the loaded module:
- the OpenZFS version in base is 2.0
- we are using the in tree-module ("FreeBSD")
- the last merged OpenZFS git revision ("gf11b09dec")
With future merges the git revision tag should be updated.
As we are merging from OpenZFS master branch and already include features
like dRAID, referencing patchlevel releases (2.0.1, 2.0.2) is pointless.
Reviewed by: freqlabs
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D28447
This code implements a version of the devres framework found
working for various iwlwifi use cases and also providing functions
for ttm_page_alloc_dma.c from DRM.
Part of the framework replicates the consumed KPI, while others
are internal helper functions.
In addition the simple devm_k*malloc() consumers were implemented
and kvasprintf() was enhanced to also work for the devm_kasprintf()
case.
Addmittingly lkpi_devm_kmalloc_release() could be avoided but for
the overall understanding of the code and possible memory tracing
it may still be helpful.
Further devsres consumer are implemented for iwlwifi but will follow
later as the main reason for this change is to sort out overlap with
DRM.
Sponsored-by: The FreeBSD Foundation
Obtained-from: bz_iwlwifi
MFC After: 3 days
Reviewed-by: hselasky, manu
Differential Revision: https://reviews.freebsd.org/D28189
Implement linux firmware KPI compat code.
This includes: request_firmware() request_firmware_nowait(),
request_firmware_direct(), firmware_request_nowarn(),
and release_firmware().
Given we will try to map requested names from natively ported
or full-linuxkpi-using drivers to a firmware(9) auto-loading
name format (.ko file name and image name matching),
we quieten firmware(9) and print success or failure (unless
the _nowarn() version was called) in the linuxkpi implementation.
At the moment we try up-to 4 different naming combinations,
with path stripped, original name, and requested name with '/'
or '.' replaced.
We do not currently defer loading in the "nowait" case.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: Rubicon Communications, LLC ("Netgate")
(firmware(9) nowarn update from D27413)
MFC after: 3 days
Reviewed by: kib, manu (looked at older versions)
Differential Revision: https://reviews.freebsd.org/D27414
This node is part of an A10-NSP (L2-BSA) development.
Carrier networks tend to stack three or more tags for internal
purposes and therefore hiding the service tags deep inside of the
stack. When decomposing such an access network frame, the processing
order is typically reversed: First distinguish by service, than by
other means.
This new netgragh node allows to bring the relevant VLAN in front (to
the out-most position). This way other netgraph nodes (like ng_vlan)
can operate on this specific type.
Reviewed by: manpages (gbe), brueffer (manpages), kp
Approved by: kp (mentor)
MFC after: 1 month
Relnotes: yes
Sponsored by: IKS Service GmbH
Differential Revision: https://reviews.freebsd.org/D22076
nids(4) was a clever idea in the early 2000's when the market was
flooded with 10/100 NICs with Windows-only drivers, but that hasn't been
the case for ages and the driver has had no meaningful maintenance in
ages. It only supports Windows-XP era drivers.
Also remove:
- ndis support from wpa_supplicant
- ndiscvt(8)
Reviewed By: emaste, bcr (manpages)
Differential Revision: https://reviews.freebsd.org/D27609
Since we use --input-type binary these options are rather meaningless. Both
binutils and elftoolchain ignore the option in this case, but LLVM does not,
and instead strips all symbols from the output file, causing missing symbols at
run time if building with llvm-objcopy. Thus simply remove the options; the
linux module has never included them for building its VDSO (added in r283407),
but for some reason the original commit of linux64 (r283424) added them.
These should however eventually be changed to use template assembly files as is
now done for firmware and MFS_IMAGE.
Reviewed by: emaste, trasz
Differential Revision: https://reviews.freebsd.org/D27740
Currently only amd64, i386 and powerpc build VirtIO modules, yet all other
architectures have at least one kernel configuration that includes the
transport drivers, and so they lack drivers for all the devices they don't
statically compile into the kernel. Instead, enable the build everywhere so all
architectures have the full set of device drivers available.
Reviewed by: bryanv (earlier version), imp (earlier version)
Differential Revision: https://reviews.freebsd.org/D28058
Many I2C "compatibility" mouse devices found on touchpads continue to
return last report data in sampling mode after touch has been ended.
That results in cursor drift. Filter out such a reports with comparing
content of current report with content of previous one.
Reported by: many
Tested by: omatsuda, gllb (github.com)
Obtained from: sysutils/iichid
Use the existing legacy PCI driver as the basis for shared code
between the legacy and modern PCI drivers. The existing virtio_pci
kernel module will contain both the legacy and modern drivers.
Changes to the virtqueue and each device driver (network, block, etc)
for V1 support come in later commits.
Update the MMIO driver to reflect the VirtIO bus method changes, but
the modern compliance can be improved on later.
Note that the modern PCI driver requires bus_map_resource() to be
implemented, which is not the case on all archs.
The hw.virtio.pci.transitional tunable default value is zero so
transitional devices will continue to be driven via the legacy
driver.
Reviewed by: grehan (mentor)
Differential Revision: https://reviews.freebsd.org/D27856
This driver supports some arm and arm64 boards equipped with
"snps,dw-wdt"-compatible watchdog device.
Tested on RK3399-based board (RockPro64).
Once started watchdog device cannot be stopped.
Interrupt handler has mode to kick watchdog even when software does not do it
properly.
This can be controlled via sysctl: dev.dwwdt.prevent_restart.
Also - driver handles system shutdown and prevents from restart when system
is asked to reboot.
Submitted by: kjopek@gmail.com
Differential Revision: https://reviews.freebsd.org/D26761
With newer AMD GPUs (>=Navi,Renoir) there is FPU context usage in the
amdgpu driver.
The `kernel_fpu_begin/end` implementations in drm did not even allow nested
begin-end blocks.
Submitted by: Greg V
Reviewed By: manu, hselasky
Differential Revision: https://reviews.freebsd.org/D28061
A driver can register a shrinker that will be called when the kernel
wants to free some memory.
Add support for that in linuxkpi and call the registered shrinkers
when the lowmem event is triggered.
Reviewed by: bz
Differential Revision: https://reviews.freebsd.org/D27728
This module intended to measure performance of routing lookups.
Uses a list of IP addresses specified by sysctl one-by-one.
Performance testing is triggered by changing sysctl OID with a number of lookups to execute.
Lookups are done by the chunks of 10K routes, entering/exiting epoch on
chunk granularity to amortise cost.
Example:
make -C sys/modules/test/fib_lookup unload load
for i in `cat ~/ip4.txt`; do sysctl net.route.test.add_inet_addr=$i; done
for i in `cat ~/ip6.txt`; do sysctl net.route.test.add_inet6_addr=$i; done
sysctl net.route.test.run_inet=10000000
dmesg | tail
Dec 13 23:24:05 current kernel: 10000000 packets in 417240173 nanoseconds, 23967011 pps
Dec 13 23:24:06 current kernel: run: 10000000 packets vnet 0xfffff80003073f00
Dec 13 23:24:07 current kernel: 10000000 packets in 423086254 nanoseconds, 23635842 pps
Differential Revision: https://reviews.freebsd.org/D27604
This change introduces loadable fib lookup modules based on
DPDK rte_lpm lib targeted for high-speed lookups in large-scale tables.
It is based on the lookup framework described in D27401.
IPv4 module is called dpdk_lpm4. It wraps around rte_lpm [1] library.
This library implements variation of DIR24-8 [2] lookup algorithm.
Module provide lockless route lookups and in-place incremental updates,
allowing for good RIB performance.
IPv6 module is called dpdk_lpm6. It wraps around rte_lpm6 [3] library.
Implementation can be seen as multi-bit trie where the stride or number of bits
inspected on each level varies from level to level.
It can vary from 1 to 14 memory accesses, with 5 being the average value
for the lengths that are most commonly used in IPv6.
Module provide lockless route lookups for global unicast addresses
and in-place incremental updates, allowing for good RIB performance.
Implementation details:
* wrapper code lives in `sys/contrib/dpdk_rte_lpm/dpdk_lpm[6].c`.
* rte_lpm[6] implementation contains both RIB and FIB code.
. RIB ("rule_") code, backed by array of hash tables part has been commented out,
as base radix already provides all the necessary primitives.
* link-local lookups are currently implemented as base radix lookup.
This part should be converted to something like read-only radix trie.
Usage detail:
Compile kernel with option FIB_ALGO and load dpdk_lpm4/dpdk_lpm6
module at any time. They will be picked up automatically when
amount of routes raises to several thousand.
[1]: https://doc.dpdk.org/guides/prog_guide/lpm_lib.html
[2]: http://yuba.stanford.edu/~nickm/papers/Infocom98_lookup.pdf
[3]: https://doc.dpdk.org/guides/prog_guide/lpm6_lib.html
Differential Revision: https://reviews.freebsd.org/D27412
A test of this is funcs/tst.strtok.d which has this filter:
BEGIN
/(this->field = strtok(this->str, ",")) == NULL/
{
exit(1);
}
The test will randomly fail with exit status of 1 indicating that this->field
was NULL even though printing it out shows it is not.
This is compiled to the DTrace instruction set:
// Pushed arguments not shown here
// call strtok() and set result into %r1
07: 2f001f01 call DIF_SUBR(31), %r1 ! strtok
// set thread local scalar this->field from %r1
08: 39050101 stls %r1, DT_VAR(1281) ! DT_VAR(1281) = "field"
// Prepare for the == comparison
// Set right side of %r2 to NULL
09: 25000102 setx DT_INTEGER[1], %r2 ! 0x0
// string compare %r1 (strtok result) to %r2
10: 27010200 scmp %r1, %r2
In this case only %r1 is loaded with a string limit set to lim1. %r2 being
NULL does not get loaded and does not set lim2. Then we call dtrace_strncmp()
with MIN(lim1, lim2) resulting in passing 0 and comparing neither side.
dtrace_strncmp() handles this case fine and it already has been while
being lucky with what lim2 was [un]initialized as.
Reviewed by: markj, Don Morris <dgmorris AT earthlink.net>
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D27671
Remove wi(4). pccard is going away, and wi only supports PC Card
devices, though it has a minor amount of glue to also support
PCI cards. However, removing the one without removing the other
is hard, so the whole driver is being removed.
Relnotes: Yes
pccard is being removed, so remove bt3c driver since it only has PC
Card attachment. Also remove bt3cfw(8) since it's the firmware for this
driver.
Relnotes: Yes
PC Card support is being removed, so remove its attachment here. ndis
is slated to be removed entirely for 13, but that's not been done yet.
Relnotes: Yes
This change includes:
hpen - Generic / MS Windows compatible HID pen tablet driver.
hgame - Generic game controller and joystick driver.
xb360gp - Xbox360-compatible game controller driver.
Submitted by: Greg V <greg_unrelenting.technology>
Reviewed by: hselasky (as part of D27993)
hidmap is a kernel module that maps HID input usages to evdev events.
Following dependent drivers is included in the commit:
hms - HID mouse driver.
hcons - Consumer page AKA Multimedia keys driver.
hsctrl - System Controls page (Power/Sleep keys) driver.
ps4dshock - Sony DualShock 4 gamepad driver.
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27993
which installs /dev/uhid# alias to hidraw character device for
compatibility with some existing uhid(4) users like Firefox.
As side effect it renames traditional uhid(4) driver to hidraw
to make possible using of common unit number allocator.
Requested by: Greg V <greg_unrelenting.technology>
Reviewed by: hselasky (as part of D27992)
This driver provides raw access to HID devices through uhid(4)-compatible
interface and is based on pre-8.x uhid(4) code. Unlike uhid(4) it does
not take devices in to monopoly ownership and allows parallel access
from other drivers.
hidraw supports Linux's hidraw-compatible interface as well.
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27992
This change implements hid_if.m methods for HID-over-USB protocol [1].
Also, this change adds USBHID_ENABLED kernel option which changes
device_probe() priority and adds/removes PnP records to prefer usbhid
over ums, ukbd, wmt and other USB HID device drivers and vice-versa.
The module is based on uhid(4) driver. It is disabled by default for
now due to conflicts with existing USB HID drivers.
[1] https://www.usb.org/sites/default/files/hid1_11.pdf
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27893
hidquirk(4) is derived from usb_quirk(4) and inherits all its HID-related
functionality. It does not support ioctl(2) interface yet.
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27890
This driver provides support for multiple HID driver attachments
to single HID transport backend. This ability existed in Net/OpenBSD
(uhidev and ihidev drivers) but has never been ported to FreeBSD.
Unlike Net/OpenBSD we do not use report number alone to distinct report
source but we follow MS way and use a top level collection (TLC) usage
index that report belongs to as a location key.
The driver performs child device autodiscovery based on HID report
descriptor data, proxying of HID requests from child devices to parent
transport backends and broadcasting of interrupts in backward direction.
Differential revision: https://reviews.freebsd.org/D27888
Create an abstract HID interface that provides hardware independent
access to HID capabilities and functions through the device tree.
hid_if.m resembles existing USBHID KPI and consist of next methods:
HID method USBHID variant
-----------------------------------------------------------------------
hid_intr_setup usbd_transfer_setup (INTERRUPT IN xfer)
hid_intr_unsetup usbd_transfer_unsetup (INTERRUPT IN xfer)
hid_intr_start usbd_transfer_start (INTERRUPT IN xfer)
hid_intr_stop usbd_transfer_drain (INTERRUPT IN xfer)
hid_intr_poll usbd_transfer_poll (INTERRUPT IN xfer)
hid_get_rdesc usbd_req_get_report_descriptor
hid_read No direct analog. Not intended for common use.
hid_write uhid(4) write()
hid_get_report usbd_req_get_report
hid_set_report usbd_req_set_report
hid_set_idle usbd_req_set_idle
hid_set_protocol usbd_req_set_protocol
This change is part of D27888
This does an import of quirk stubs, debugging macros from USB code and
numerous usage constants used by dependent drivers.
Besides, this change renames some functions to get a better matching
with userland library and NetBSD/OpenBSD HID code. Namely:
- Old hid_report_size() renamed to hid_report_size_max()
- New hid_report_size() calculates size of given report rather than
maximum size of all reports.
- hid_get_data_unsigned() renamed to hid_get_udata()
- hid_put_data_unsigned() renamed to hid_put_udata()
Compat shim functions are provided in usbhid.h to make possible compile
of legacy code unmodified after this change.
Reviewed by: manu, hselasky
Differential revision: https://reviews.freebsd.org/D27887
It will be used by the upcoming HID-over-i2C implementation. Should be
no-op, except hid.ko module dependency is to be added to affected drivers.
Reviewed by: hselasky, manu
Differential revision: https://reviews.freebsd.org/D27867
Only ACPI attachment is supported for now, some others depend on the
presence of smbios(4) support, which we lack on arm64.
Reviewed by: emaste
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D28009
Enable build of IPMI over OPAL on powerpc64le
Reviewed by: bdragon
Sponsored by: Eldorado Research Institute (eldorado.org.br)
Differential Revision: https://reviews.freebsd.org/D27443
- Suppress -Wredundant-decls. Ultimately this warning is harmless in
any case, and it does not look like there is a simple way to avoid
redundant declarations in this case without a lot of header pollution
(e.g. having openzfs's shim param.h pulling in sys/kernel.h for hz).
- Suppress -Wnested-externs, which is useless anyway.
Unfortunately it was not sufficient just to modify OPENZFS_CFLAGS,
because the warning suppressions need to appear on the command line
after they are explicitly enabled by CWARNFLAGS from sys/conf/kern.mk,
but OPENZFS_CFLAGS get added before due to use of -I for the shims.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D27685
These drivers should have been removed along with tl(4) as part of
7c897ca91f and r347918 respectively
as these fromer made sure to only ever attach to the latter, e. g.:
<...>
static int
tlphy_probe(device_t dev)
{
if (!mii_dev_mac_match(dev, "tl"))
return (ENXIO);
<...>
r368193 was suppsed to rename the MOF firmware image, but the
qat_c2xxxfw makefile defined the two images in the wrong order so the
MMP image was renamed instead.
MFC after: 3 days
Sponsored by: Rubicon Communications, LLC (Netgate)
Don't tell it to look for headers in a non-existent directory.
Reviewed by: imp, mmacy
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D27565
The hme (Happy Meal Ethernet) driver was the onboard NIC in most
supported sparc64 platforms. A few PCI NICs do exist, but we have seen
no evidence of use on non-sparc systems.
Reviewed by: imp, emaste, bcr
Sponsored by: DARPA
Macfilter to route packets through different hooks based on sender MAC address.
Based on ng_macfilter written by Pekka Nikander
Sponsered by Retina b.v.
Reviewed by: afedorov
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D27268
In r367395 parts of machine dependent linux_dummy.c were moved to a new
machine independent file sys/compat/linux/linux_dummy.c and the existing
linux_dummy.c was renamed to linux_dummy_machdep.c.
Add linux_dummy_machdep.c to the linux module for i386.
Rename sys/amd64/linux32/linux_dummy.c for consistency.
Add the new linux_dummy.c to the linux module for i386.
Enable in-kernel acceleration of SHA1 and SHA2 operations on arm64 by adding
support for the ossl(4) crypto driver. This uses OpenSSL's assembly routines
under the hood, which will detect and use SHA intrinsics if they are
supported by the CPU.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27390
Make room for adding arm64 support to this driver by moving the
x86-specific feature parsing to a separate file.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D27388
If firmware_get() fails to find a loaded firmware image, it searches for
candidate KLDs to load. It will search for a KLD containing a module
with the same name as the requested image, and failing that, will load a
KLD with the same basename as the requested image.
The module name given by fw_stub.awk is simply "<mangled KLD name>_fw".
QAT firmware modules contain two images, neither of which match either
of the names used during lookup, so automatic loading of firmware images
after mountroot does not work. Work around this by using the same
string for the first image name and for the KLD basename.
MFC after: 3 days
Sponsored by: Rubicon Communications, LLC (Netgate)
