The "Intel Sunrise Point-LP USB 3.0 controller" doesn't update the wMaxPacket
field in the control endpoint context automatically causing a BABBLE error code
on the initial first USB device descriptor read, when the bMaxPacketSize is not
8 bytes.
Reported by: wulf@
PR: 248784
MFC after: 1 week
Sponsored by: Mellanox Technologies
The AMD's Ryzen 3 3200g XHCI controllers apparently need the evaluate
control endpoint context command, but we don't need to issue this
command when the bMaxPacketSize is received after the read of the USB
device descriptor, because this part should be handled automatically.
PR: 248784
Tested by: emaste, hselasky
MFC after: 1 week
Sponsored by: Mellanox Technologies
The XHCI specification says that the XHCI controller should detect
reception of the USB device descriptors, and automatically update
the max packet size in the control endpoint context.
Differential Revision: https://reviews.freebsd.org/D26104
Reviewed by: kp@
MFC after: 1 week
Sponsored by: Mellanox Technologies
don't implement link power management, LPM.
This fixes error code XHCI_TRB_ERROR_BANDWIDTH for isochronous USB 3.0
transactions.
Submitted by: Horse Ma <Shichun.Ma@dell.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
because it clobbers the super speed link status when a device is in super
speed mode. Currently the power bit is not needed for anything in the USB
hub driver.
This fixes USB warm reset for super speed devices.
Tested by: Shichun.Ma@dell.com
MFC after: 3 days
Sponsored by: Mellanox Technologies
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
This avoids getting the XHCI_TRB_ERROR_CONTEXT_STATE error code from the XHCI
controller when the endpoint is disabled or already stopped.
Suggested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
Do not configure any endpoint twice, but instead keep track of which
endpoints are configured on a per device basis, and use an evaluate
endpoint context command instead. When changing the configuration make
sure all endpoints get deconfigured and the configured endpoint mask
is reset.
This fixes an issue where an endpoint might stop working if there is
an error and the endpoint needs to be reconfigured as a part of the
error recovery mechanism in the FreeBSD USB stack.
Tested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
above 1Kbyte. It might look like some XHCI(4) controllers do not
support when the USB control transfer is split using a link TRB. The
next NORMAL TRB after the link TRB is simply failing with XHCI error
code 4. The quirk ensures we allocate a 64Kbyte buffer so that the
data stage TRB is not broken with a link TRB.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
sure the XHCI controller is reset after halting it. The problem is
clearly a BIOS bug as the suspend and resume is failing without
loading the XHCI driver. The same happens when using Linux and the
XHCI driver is not loaded.
Submitted by: Yanko Yankulov <yanko.yankulov@gmail.com>
PR: 216261
MFC after: 1 week
its own job because this breaks the simplified QEMU XHCI TRB parser,
which expects the complete USB control transfer as a series of back to
back TRBs. The old behaviour is kept under #ifdef in case this change
breaks enumeration of any USB devices.
PR: 212021
MFC after: 1 week
configuring of EP0 and non-EP0 into xhci_cmd_evaluate_ctx() and
xhci_cmd_configure_ep() respectivly. This resolves some errors when
using XHCI under QEMU and gets is more in line with the XHCI
specification.
PR: 212021
MFC after: 1 week
version of the XHCI specification. Make sure the code can handle the
maximum number of allowed scratch pages.
Submitted by: Shichun_Ma@Dell.com
Approved by: re (hrs)
MFC after: 1 week
requesting the initial complete device descriptor and not as part of
the subsequent babble error recovery. Babble means that the received
USB packet was bigger than than configured maximum packet size. This
only affects enumeration of FULL speed USB devices which use a
bMaxPacketSize different from 8 bytes. This patch might help fix
enumeration of USB devices which exhibit USB I/O errors in dmesg
during boot.
MFC after: 1 week
xhci_start_controller() to xhci_init(). These values don't change at run-
time so there's no point of acquiring them on every USB_HW_POWER_RESUME
instead of only once during initialization. In r276717, reading the first
couple of registers in question already had been moved as a prerequisite
for the changes in that revision.
- Identify ASMedia ASM1042A controllers.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
when re-enumerating a FULL speed device. Else the wrong max packet
setting might be used when trying to re-enumerate a FULL speed device.
MFC after: 3 days
that we should use a normal-TRB if there are more TRBs extending the
data-stage TRB. Add a dedicated state bit to the internal USB transfer
flags to handle this case.
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
MFC after: 1 week
is called from "xhci_configure_reset_endpoint()". Ensure the 3-strikes
error feature is always enabled except for ISOCHRONOUS transfers.
MFC after: 1 week
Suggested by: marius@
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
direction isochronous transfers.
- Remove setting of fields which does not belong to the respective
TRBs. These fields are currently set as zero and this is more a
cosmetic change.
MFC after: 3 days
Submitted by: Horse Ma <HMa@wyse.com>
