As is done in the target, require that DataSN values are consecutive
and in-order. If an out of order Data-In PDU is received, force a
session reconnect. In addition, when a SCSI Response PDU is received,
verify that the ExpDataSN field matches the count of Data-In PDUs
received for this command. If not, force a session reconnect.
Reviewed by: mav
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D31594
Similar to TSO, iSCSI segmentation offload permits the upper layers to
submit a "large" virtual PDU which is split up into multiple segments
(PDUs) on the wire. Similar to how the TCP/IP headers are used as
templates for TSO, the BHS at the start of a large PDU is used as a
template to construct the specific BHS at the start of each PDU. In
particular, the DataSN is incremented for each subsequent PDU, and the
'F' flag is only set on the last PDU.
struct icl_conn has a new 'ic_hw_isomax' field which defaults to 0,
but can be set to the largest virtual PDU a backend supports. If this
value is non-zero, the iSCSI target and initiator use this size
instead of 'ic_max_send_data_segment_length' to determine the maximum
size for SCSI Data-In and SCSI Data-Out PDUs. Note that since PDUs
can be constructed from multiple buffers before being dispatched, the
target and initiator must wait for the PDU to be fully constructed
before determining the number of DataSN values were consumed (and thus
updating the per-transfer DataSN value used for the start of the next
PDU).
The target generates large PDUs for SCSI Data-In PDUs in
cfiscsi_datamove_in(). The initiator generates large PDUs for SCSI
Data-Out PDUs generated in response to an R2T.
Reviewed by: mav
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D31222
xpt_bus_register and xpt_bus_deregister returns a hybrid error that's
neither a cam_status, nor an errno, but a mix of both. Update
xpt_bus_register and xpt_bus_deregister to return an errno. The vast
majority of current users compare against zero, which can also be
spelled CAM_SUCCESS. Nobody uses CAM_FAILURE, so remove that symbol
to prevent comfusion (nothing returns it either).
Where the return value is saved, ensure that the variable 'error' is
used to store an errno and 'status' is used to store a cam_status where
it makes the code clearer (usually just in functions that already mix
and match). Where the return value isn't used at all, avoid storing it
at all.
Reviewed by: scottl@, mav@ (earlier version)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D30860
This fixes a few bugs in iSCSI backends where the backends were using
the limits they advertised initially during the login phase as the
final values instead of the values negotiated with the other end.
Reported by: Jithesh Arakkan @ Chelsio
Reviewed by: mav
Differential Revision: https://reviews.freebsd.org/D30271
iscsid can be sleeping in iscsi_ioctl() causing the destroy_dev() to
sleep forever if iscsi.ko is unloaded while iscsid is running.
Reported by: Jithesh Arakkan @ Chelsio
Reviewed by: mav
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D29688
Previously, iscsi_poll() just panicked. This meant if you got a panic
on a box when using the iSCSI initiator, the attempt to shutdown would
trigger a nested panic and never write out a core. Now, CCB's sent to
iSCSI devices (such as the sychronize-cache request in dashutdown())
just fail with a timeout during a panic shutdown.
Reviewed by: scottl, mav
MFC after: 2 weeks
Sponsored by: Chelsio
Differential Revision: https://reviews.freebsd.org/D28455
DataSN for solicited Data-Out is per-R2T. Since we handle whole R2T
in one go, we don't need to store it anywhere, especially in global
per-command structure. This may allow us to handle multiple R2T per
command at once, if we decide, or may be relax locking.
Rename the second use of that field to io_referenced_task_tag.
MFC after: 1 month
RFC 7143 (11.2.1.8):
An ITT value of 0xffffffff is reserved and MUST NOT be assigned for a
task by the initiator. The only instance in which it may be seen on
the wire is in a target-initiated NOP-In PDU (Section 11.19) and in
the initiator response to that PDU, if necessary.
MFC after: 1 month
Replace MAXPHYS by runtime variable maxphys. It is initialized from
MAXPHYS by default, but can be also adjusted with the tunable kern.maxphys.
Make b_pages[] array in struct buf flexible. Size b_pages[] for buffer
cache buffers exactly to atop(maxbcachebuf) (currently it is sized to
atop(MAXPHYS)), and b_pages[] for pbufs is sized to atop(maxphys) + 1.
The +1 for pbufs allow several pbuf consumers, among them vmapbuf(),
to use unaligned buffers still sized to maxphys, esp. when such
buffers come from userspace (*). Overall, we save significant amount
of otherwise wasted memory in b_pages[] for buffer cache buffers,
while bumping MAXPHYS to desired high value.
Eliminate all direct uses of the MAXPHYS constant in kernel and driver
sources, except a place which initialize maxphys. Some random (and
arguably weird) uses of MAXPHYS, e.g. in linuxolator, are converted
straight. Some drivers, which use MAXPHYS to size embeded structures,
get private MAXPHYS-like constant; their convertion is out of scope
for this work.
Changes to cam/, dev/ahci, dev/ata, dev/mpr, dev/mpt, dev/mvs,
dev/siis, where either submitted by, or based on changes by mav.
Suggested by: mav (*)
Reviewed by: imp, mav, imp, mckusick, scottl (intermediate versions)
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D27225
Foundation copyrights, approved by emaste@. It does not include
files which carry other people's copyrights; if you're one
of those people, feel free to make similar change.
Reviewed by: emaste, imp, gbe (manpages)
Differential Revision: https://reviews.freebsd.org/D26980
SAM-3 specification introduced concept of Task Priority, that was renamed
to Command Priority in SAM-4, and supported by all modern SCSI transports.
It provides 15 levels of relative priorities: 1 - highest, 15 - lowest and
0 - default. SAT specification for SATA devices translates priorities 1-3
into NCQ high priority.
This change adds new "priority" field into empty spots of struct ccb_scsiio
and struct ccb_accept_tio of CAM and struct ctl_scsiio of CTL. Respective
support is added into iscsi(4), isp(4), mpr(4), mps(4) and ocs_fc(4) drivers
for both initiator and where applicable target roles. Minimal support was
added to CTL to receive the priority value from different frontends, pass it
between HA controllers and report in few places.
This patch does not add consumers of this functionality, so nothing should
really change yet, since the field is still set to 0 (default) on initiator
and not actively used on target. Those are to be implemented separately.
I've confirmed priority working on WD Red SATA disks connected via mpr(4)
and properly transferred to CTL target via iscsi(4), isp(4) and ocs_fc(4).
While there, added missing tag_action support to ocs_fc(4) initiator role.
MFC after: 1 month
Relnotes: yes
Sponsored by: iXsystems, Inc.
It does not change anything immediately, but allows further support of
Command Priority, Status Qualifier and new task management functions.
MFC after: 1 month
Sponsored by: iXsystems, Inc.
another thread has started to send in a CCB and already checked
the queue wasn't frozen, we would end up with iscsi_action()
being called despite the queue is now frozen.
Add a check to make sure this doesn't happen . Perhaps this should
be fixed at the CAM level instead, but given how the send queue and
SIM are governed by two separate mutexes, it is somewhat hard to do.
Reviewed by: imp, mav
MFC after: 2 weeks
Sponsored by: NetApp, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D26750
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: kib, trasz
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23640
this check on open, but "iscsictl -M", or an iSCSI redirect received by
iscsid(8) could end up with two sessions with the same target name and
portal.
MFC after: 2 weeks
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
can be used prior to the ISCSIDHANDOFF IOCTL which set the negotiated values.
Else the login PDU will fail when passing the "-r" option to "iscsictl" which
means iSCSI over RDMA instead of TCP/IP.
Discussed with: np@ and trasz@
Sponsored by: Mellanox Technologies
MFC after: 1 week
CAM_REQ_ABORTED sounds natural for aborting outstanding requests when
tearing down a session, but that status actually causes eligible
requests to be tried again. That's completely useless, so let's use
CAM_DEV_NOT_THERE instead. Perhaps there is a better status, but this
should be good enough. The change should affect only the session
termination.
Tested by: Ben RUBSON <ben.rubson@gmail.com>
Reviewed by: mav, trasz
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D12653
It should be sufficient to hold the lock just for removing the session
from the session list. Everything else should be covered by the session
specific lock.
On top of that, at present we can get a deadlock caused by waiting on
the CAM SIM reference count while holding the global lock. A specific
scenario involving ZFS is this:
- concurrent termination of two sessions, S1 and S2
- session S1 completed all I/Os and sleeps in CAM waiting for device
close by ZFS;
- session S2 is also dead now, but can not forcefully complete
outstanding requests by calling iscsi_session_cleanup() from
iscsi_maintenance_thread_terminate(), since it can't get the same
global sc_lock;
- as soon as there are unfinished requests, ZFS can not do
spa_config_enter() as writer, and so can not close the device for
session S1;
- deadlock.
Reported by: Ben RUBSON <ben.rubson@gmail.com>
Tested by: Ben RUBSON <ben.rubson@gmail.com>
Reviewed by: mav, trasz
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D12652
Decouple the send and receive limits on the amount of data in a single
iSCSI PDU. MaxRecvDataSegmentLength is declarative, not negotiated, and
is direction-specific so there is no reason for both ends to limit
themselves to the same min(initiator, target) value in both directions.
Allow iSCSI drivers to report their send, receive, first burst, and max
burst limits explicitly instead of using hardcoded values or trying to
derive all of them from the receive limit (which was the only limit
reported by the drivers prior to this change).
Display the send and receive limits separately in the userspace iSCSI
utilities.
Reviewed by: jpaetzel@ (earlier version), trasz@
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7279
discovery without attaching to the targets ("iscsictl -Ad ... -e off"),
and then attach to selected ones ("iscsictl -Mi ... -e on").
PR: 204129
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6633
method. This is required for upcoming iSER support.
Obtained from: Mellanox Technologies (earlier version)
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Ensure that all iSCSI sessions are correctly terminated during shutdown.
* Enhances the changes done by r286226 (D3052).
* Add shutdown post sync event to run after filesystem shutdown
(SHUTDOWN_PRI_FIRST) but before CAM shutdown (SHUTDOWN_PRI_DEFAULT).
* Changes iscsi_maintenance_thread to processes terminate in preference to
reconnect.
Reviewed by: trasz
MFC after: 2 weeks
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D4429
r291227:
s/is->is_conn/ic to shorten things a bit.
r291228:
Do not generate PDUs with payload greater than max_data_segment_length.
It is perhaps preferable to have a separate limit for send instead of
reusing the receive limit. I'll discuss with trasz@ and mav@ before
pulling this into head.
r292618:
Add comment to go with r291228.
iscsi's shutdown_pre_sync prio was SHUTDOWN_PRI_FIRST which caused it to
run before other high priority handlers such as filesystems e.g. ZFS.
This meant the iscsi sessions where removed before the ZFS geom consumer
was closed, resulting in a panic from g_access calls on debug kernels
due to negative acr.
Instead use the same as the old iscsi_initiator SHUTDOWN_PRI_DEFAULT-1
which allows it to run before dashutdown etc but after filesystems.
MFC after: 2 weeks
Sponsored by: Multiplay
It is perhaps preferable to have a separate limit for send instead of
reusing the receive limit. I'll discuss with trasz@ and mav@ before
pulling this into head.
hangs on shutdown with LUNs with mounted filesystems over a disconnected
iSCSI session.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3052
