CB710, CB720, CB1211, CB1225, CB1410 and CB1420
These are likely licensed designed from TI, and the Linux PCMCIA code
treats them as TI chips.
Add comment, but no ID for the 711E1 from O2Micro.
vendors that list the vendor ID in the proper byte order. The second
section is for vendors that get it backwards. The third is for what
appear to be 'random' ones (although 0xcxxx appears to be coherent
enough that maybe somebody else is assigning those numbers).
o AD1980 hook.
o ac97_fix_auxout.
and:
o Associate AC97_MIX_AUXOUT with SOUND_MIXER_OGAIN rather than
SOUND_MIXER_MONITOR.
o Add ac97_fix_tone to remove tone controls from mixer if invalid.
are all bogus, and the cards that don't decode things quite right
often have hundreds of them. This will fix starvation of small dmesg
buffers and allow better debugging to happen. I thought about adding
an override, but there is such a thing as too many knobs. :-)
- Fix up TX speed changes.
- Make mpi-350 cards sort-of work with new firmware. It RXs okay but TXs
only work for about 14 packets then fails to get an interrupt. The
TX watchdog fires. It has been reported that my hack for now doesn't
break cards with the older firmware. It appears my card has lost
the ability to RX or TX at all but other peoples cards work. I assume
it got damaged in tansport.
MFC: 1 week.
count handling of station entries in hostap mode:
Input path:
o driver is now expected to find the node associated with the
sender of a received frame; use ic_bss if none is located
o driver passes the (referenced) node into ieee80211_input for
use within the wlan module and is responsible for cleaning up
on return
o the antenna state is no longer passed up with each frame; this
is now considered driver-private state and drivers are responsible
for keeping it in the driver-private part of a node
Output path:
Revamp output path for management frames to eliminate redundant
locking that causes problems and to correct reference counting
bogosity that occurs when stations are timed out due to inactivity
(in AP mode). On output the refcnt'd node is stashed in the pkthdr's
recvif field (yech) and retrieved by the driver. This eliminates
an unref/ref scenario and related node table unlock/lock due to the
driver looking up the node. This is particularly important when
stations are timed out as this causes a lock order reversal that
can result in a deadlock. As a byproduct we also reduce the overhead
for sending management frames (minimal). Additional fallout from
this is a change to ieee80211_encap to return a refcn't node for
tieing to the outbound frame. Node refcnts are not reclaimed until
after a frame is completely processed (e.g. in the tx interrupt
handler). This is especially important for timed out stations as
this deref will be the final one causing the node entry to be
reclaimed.
Additional semi-related changes:
o replace m_copym use with m_copypacket (optimization)
o add assert to verify ic_bss is never free'd during normal operation
o add comments explaining calling conventions by drivers for frames
going in each direction
o remove extraneous code that "cannot be executed" (e.g. because
pointers may never be null)
quietly discard them; this just permits them to be collected with bpf)
o add a counter for the number of rate control frames discarded when not in
monitor mode
o move the rx "too short" statistic in the stat structure so non-error rx stats
are together (NB: ABI change to apps that collect stats via driver ioctl)
mistakes (this mistake was not an issue because the length is only used to
decide whether or not to allocate a cluster)
o while here, move a beacon length comment to the "right place"
present, and non-zero when it is (or may be) absent. The test
cbb_child_present was backwards. However, typical usage in the tree
would cause it to do the right thing because the card really wasn't
there the OK flag would be turned on.
Also, assume that if any of these bits are turned on we don't have a
card, rather than requiring both of them in the suspend/resume
routines.
Noticed by: cognet
to what is in NetBSD. I have a few cards that tickles this bug, and
this just keeps us from panicing. It doesn't actually fix the problem
(that will happen once I figure out why some cards hate the address
their CIS is mapped to high memory).
A timecounter will be selected when registered if its quality is
not negative and no less than the current timecounters.
Add a sysctl to report all available timecounters and their qualities.
Give the dummy timecounter a solid negative quality of minus a million.
Give the i8254 zero and the ACPI 1000.
The TSC gets 800, unless APM or SMP forces it negative.
Other timecounters default to zero quality and thereby retain current
selection behaviour.
Correctly handle additional disks without BIOS partition tables.
Previously, vinum_scandisk stopped scanning additional disks for
native partitions after any good partition was found. This applies
to all platforms, but was a particular problem on systems without
BIOS partition tables.
Submitted by: harti
the hardware mutex if it is held. Re-add calls to Enable/Clear fixed events.
This is not known to have caused problems. Bug symptoms might have included
instability after an aborted suspend attempt or power/sleep buttons not
being enabled.
CP-168U board. It initializes and attaches in the same way as the
older (but higher performance) C168H. The only difference is the
board ID, which is 0x1681.
PR: kern/53548
Submitted by: regnauld@catpipe.net
MFC after: 1 week
the Palm device and the USB host controller deadlock. The USB host
controller is expecting an early-end-of-transmission packet with 0
data, and the Palm doesn't send one because it's already communicated
the amount of data it's going to send in a header (which ucom/uvisor
are oblivious to). This is the problem that has been known on the
pilot-link lists as the "[Free]BSD USB problem", but not understood.
Submitted by: Nathan J. Williams <nathanw@MIT.EDU>
for partly-aligned operations through /dev/crypto (unlikely)
o add missing case in iov code that never showed up because of the above bug
Submitted by: "Jason L. Wright" <jason@thought.net>
MFC after: 3 days
found only many tv-cards.
We currently use more ore less evil hacks (slow_msp_audio sysctl) to
configure the various variants of these chips in order to have
stereo autodetection work. Nevertheless, this doesn't always work
even though it _should_, according to the specs.
This is, for example, the case for some popular Hauppauge models sold
sold in Germany.
However, the Linux driver always worked for me and others. Looking at
the sourcecode you will find that the linux-driver uses a very much
enhanced approach to program the various msp34xx chipset variants,
which is also found in the specs for these chips.
This is a port of the Linux MSP34xx code, written by Gerd Knorr
<kraxel@bytesex.org>, who agreed to re-release his code under a
BSD license for this port.
A new config option "BKTR_NEW_MSP34XX_DRIVER" is added, which is required
to enable the new driver. Otherwise the old code is used.
The msp34xx.c file is diff-reduced to the linux-driver to make later
modifications easier, thus it doesn't follow style(9) in most cases.
Approved by: roger (committing this, no time to test/review),
keichii (code review)
These are 10/100 only NICs found on the IBM Thinkpad R40E and
G40. These seem to be based on the BCM5705 MAC but with a PHY
that doesn't support 1000Mbps modes.
Submitted by: Igor Sviridov <sia@nest.org>
ioctls.
In the particular case of ptrace(), this commit more-or-less reverts
revision 1.53 of sys_process.c, which appears to have been erroneous.
Reviewed by: iedowse, jhb
to configure this correctly yields many watchdog timeouts even on lightly
loaded machines. This is a common complaint from users with Dell 1750
servers with built-in dual 5704 NICs.
the time the card is inserted and the time that the card is
configured. This can lead to interrupt storms. The O2Micro suggested
workaround is to route the card function interrupt to IRQ1. It
appears from my testing that this is an acceptable workaround for most
chipsets (there's still some issue with the ricoh chipset).
Also, only look at the NOT_A_CARD bit when the bridge tells us there's
a card present. At least one test caused this to be true after the
card was removed, but the author couldn't recreate it with the
workaround in place. The change is more conservative than the
previous code, but still has the work around that wasn't present in
the older code.
BGE_MACSTAT_MI_COMPLETE bit in the MAC status register as a link
change indicator. We turn this bit on now because some of the newer
chips need it, but it usually just means that reading/writing
an MII/GMII register has completed, not that a link change has
occured.
the standard.
1) When the bridge tells us that we have a card that isn't recognized, we
use the force register to force the CV_TEST to run. This test causes the
bridge to re-evaluate the card. Once this re-evaluation process happens,
we get a new interrupt that may say it is ready to process. We try this up
to 20 times. Tests have shown that this appears to correctly reset the
'Unknown card type' problem that I saw on my Sony PCG-505TS.
2) Take a page from OLDCARD and always read the CSC register in the ISR.
Some TI (and it seems maybe Ricoh) chipsets require this to behave
properly. This work around appears to work due to some power management
protocols that were improperly implemented. Maybe it can be removed when
this driver supports the full PME# protocol described in the standards.
3) Minor additional debug printf when debugging is enabled.
4) Minor additional commentary for things that are obvious only after study.
# I'm committing this from my Sony PCG-505TS using shared PCI interrupts
# and NEWCARD, but there are some issues with the Ricoh bridge still, but
# at least now I can boot with the card inserted and have it work.
PCG-505BX (for example) has one of those:
wi0: <Intersil Prism3> mem 0xf8000000-0xf8000fff at device 2.0 on pci2
wi0: 802.11 address: 00:02:8a:94:d8:73
wi0: using RF:PRISM3(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.5.6)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
has the same product id, but different vendor id. It also appears
that the MELCO's id should be 0x18a instead of 0x8a01. Fix this.
Submitted by: Shizuka Kudo-san
and up commands. When configuring the interface down only the
connections that are currently closing are deleted from the connection
table. When the interface is configured up, all connections that
are in the table are re-opened.
connections that have been open (and were not closing) when
the interface was stopped. This makes the behaviour of fatm(4) more like
the behaviour of en(4).
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
- Build SGL's for ATA_PASSTHROUGH commands
- Fallback to using the sgl_offset when the opcode is unknown for building
SGL's/
- Add ioctl calls for adding and removing units.
- Define previously undefined AEN's
- Allocate memory for the ioctl payload in multiples of 512bytes.
MFC after: 1 week
preparation for supporting the OPENVCC and CLOSEVCC ioctls which
are needed for ng_atm. This required some re-organisation of the code
(mostly converting array indexes to pointers). This also gives us
an array of open vccs that will help in using the generic GETVCCS handler.
the macro definition, and cause the generation of syntactically
incorrect code that gcc happens to accept.
Reviewed by: schweikh (mentor)
MFC after: 4 weeks
larger than normal frames, to account for the case where a bge(4) NIC
is used with VLANs. Since we set the IFCAP_VLAN_MTU flag, we must allow
reception of frames up to 1522 bytes in size rather than 1518.
Note that it is possible to work around this bug by doing:
# ifconfig bge0 mtu 1504
prior to configuring any VLAN interfaces.
recompiling the driver. See the comments near the top of "if_em.h"
for descriptions of these delays. Four new loader tunables control
the system-wide default values:
hw.em.tx_int_delay
hw.em.rx_int_delay
hw.em.tx_abs_int_delay
hw.em.rx_abs_int_delay
The tunables are specified in microseconds. The valid range is
0-67108 usec., and 0 means that the timer is disabled.
There are also four new sysctls (actually, a set of four for each
"em" device in the system) to query and change the interrupt delays
after the system is up:
hw.em0.tx_int_delay
hw.em0.rx_int_delay
hw.em0.tx_abs_int_delay (not present for 82542/3/4 adapters)
hw.em0.rx_abs_int_delay (not present for 82542/3/4 adapters)
It seems to be OK to change these values even while the adapter is
passing traffic.
Approved by: Prafulla Deuskar <pdeuskar@FreeBSD.ORG>
MFC after: 4 weeks
- Move isa/ppc* to sys/dev/ppc (repo-copy)
- Add an attachment method to ppc for puc
- In puc we need to walk the chain of parents.
Still to do, is to make ppc(4) & puc(4) work on other platforms. Testers
wanted.
PR: 38372 (in spirit done differently)
Verified by: Make universe (if I messed up a platform please fix)
This is controlled by a per-adapter sysctl hw.atm.hfaX.shape. When
set to 0, no shaping occures. When set to 1 at most 1 channel is
shaped. When set to 2 all CBR channels are shaped. Note, that the
latter may actually not work, because of the adapter supporting
the shaping of only one PDU at the same time.
also do it). Three problems have been encountered:
1. The initialisation command does not work in interrupt mode. Whether
this is a firmware bug or a feature is not clear. The original Fore
drivers execute the initialize command always in polling mode, so
it appears that this behaviour is expected. When we detect a 4.X.Y
firmware do busy wait on the command status.
2. The command code of the GET_PROM command has changed. This is an
unofficial command anyway. What was GET_PROM in 3.X.Y is CLEAR_STATS
in 4.X.Y (although unimplemented in the firmware). We need to
use the correct code depending on the firmware.
3. The 4.X.Y firmware can set the error flag in the command status
without also setting the completion flag (as the documenation says).
Check both variants.
An additional field in the per-card structure fu_ft4 is TRUE when we have
detected a 4.X.Y firmware. Otherwise it is false. The behaviour of the
driver when using a 3.X.Y firmware should be identical to the previous
behaviour.
This change will enable traffic shaping of (at least one) CBR channels.
allocation function. With this patch, it prevents continous growth of
the devbuf memory pool.
Tested with ssh <host> dd of=/dev/null < /dev/zero and vmstat -m | grep devbuf
receive 6 byte commands. Add a check for this flag to da(4) and cd(4) so
that they honor it. This is a quick workaround for many devices (especially
USB) that require da(4) quirks to operate. The more complete approach is
to finish the new transport code which will be aware of the SCSI version a
transport implements.
MFC after: 1 day
function unless the device is configured up. Without this fix, the
device ends up in the RUNNING state even though it is configured down.
Also, check the RUNNING flag before calling the if_start function, in
case the if_init function failed for one reason or another.
contain the filedescriptor number on opens from userland.
The index is used rather than a "struct file *" since it conveys a bit
more information, which may be useful to in particular fdescfs and /dev/fd/*
For now pass -1 all over the place.
newer lucent/hermes firmware than indicated (investigating). I'm committing
this now since it shouldn't hurt anything.
o Vaguely related, add bogus frame length check from netbsd.
Obtained from: netbsd
it attaches to all existing NATM network interfaces in the system
and creates a HARP physical interface for each of them. This allows
us to use the same set of ATM drivers for all ATM stuff. It is
possible to use the same interface for HARP, NATM and netgraph at the
same time.
go looking for free fragments won't match. Since we never free this, we
can "throw away" the tag. This is very dirty, and needs to be reimplemented
properly, but fixes performance problems with uhci.
Also assert that when we overlay a structure on some space, that the
space is large enough for the structure.
namespace. To compensate for it only being used in the !ECDT case, use
a more robust approach to indicate a device was probed via ECDT by setting
the private ivar to be &acpi_ec_devclass. Without the acpi_MatchHid() call
now, it might have been possible for a non-EC device to have had its magic
match our previous flag.
Pointed out by: takawata
to EcGpeQueryHandler on to any waiting threads through the softc. Similar
behavior was in the original version.
Also:
* Merge EcQuery into EcGpeQueryHandler to simplify locking
* Hold EcLock from the initial read of the CSR down to the wakeup or
until after the query command has been processed.
* ec_gpebit only needs to be a UINT8
namespace has been evaluated. Machines with ACPI 2.0 expect this behavior
and have AML which calls EC functions early in the boot process. If the
ECDT is not available, fall back to original probe behavior.
Other minor changes:
* Add GPE bit and GLK usage to the device announcement
* Always use the global lock in the ECDT case, but potentially downgrade to
not using it if _GLK is 0 once the namespace is available. This is
announced with "Changing GLK from 1 to 0"
* Remove the acpi_object_list definitions which were earlier deprecated
Ideas from: takawata
- 5705 doesn't support jumbo frames
- Statistics must be read from registers
- RX return ring must be capped at 512 entries
- Omit initialization of certain device blocks
- Acknowledge link change interrupts by setting the 'link changed'
bit in the status register (used to have no effect)
- Remember to toggle the MI completion bit too
- Set the mbuf low watermark differently (on-chip memory buffers,
not BSD mbufs)
- Don't enable Ethernet@WireSpeed feature for certain 5705 chip revs
- Add additional PCI IDs for 5705 and 5782 parts
- Add a forgotten 5704 PCI ID
Most changes ripped kicking and screaming from the Broadcom linux driver.
Thanks to Paul Saab for sanity testing. (My lack of sanity has been
confirmed.)
sync of the NetBSD code.
fix isochornous support for ohci. This gets webcams like my OV511
working on sparc64.
PR: kern/52589
Submitted by: Bruce R. Montague (isochonous support)
Reviewed by: joe among others
callback will never be deferred. ATM needs to prevent cell and packet
ordering. Also use the default mutex and lock functions (those that
panic) for the tag creation.
with a ProATM-155 and an IDT evaluation board and should also work
with a ProATM-25 (it seems to work at least, I cannot really measure
what the card emits). The driver has been tested on i386 and sparc64,
but should work an other archs also. It supports UBR, CBR, ABR and VBR;
AAL0, AAL5 and AALraw. As an additional feature VCI/VPI 0/0 can be
opened for receiving in AALraw mode and receives all cells not claimed
by other open VCs (even cells with invalid GFC, VPI and VCI fields and
OAM cells).
Thanks to Christian Bucari from ProSum for lending two cards and answering
my questions.
MFNetBSD: revision 1.137
date: 2003/01/20 07:12:13; author: simonb;
Grrr. So much for my ability to use grep(1) effectively. Pointed out
by Stephen Degler in private mail.
date: 2002/12/10 14:07:37; author: toshii; state: Exp; lines: +6 -6
Add a couple of le32toh which were missing in the previous.
Pointed out by SOMEYA Yoshihiko.
date: 2002/12/07 07:33:20; author: toshii; state: Exp; lines: +50 -29
Update xfer->frlengths for input isoc transfer. Based on patches from
SOMEYA Yoshihiko.
Also fix error handling for isoc transfer somewhat; usb_transfer_complete
shouldn't be called for more than once.
date: 2002/12/07 07:14:28; author: toshii;
Fix several nits. Mostly from SOMEYA Yoshihiko.
- Call usbd_transfer_complete at splusb.
- Fix a botched for loop in ohci_rem_ed.
- In ohci_close_pipe, wait 1ms after removing an ED to avoid possible race
condition.
The splusb change is non-functional on FreeBSD.
The botched loop and race condition changes came from us.
This patch is non-functional.
date: 2002/09/29 20:58:25; author: augustss;
Add some spl calls to protect critical regions. From kern/18440,
Takeshi Nakayama.
(No functional change on FreeBSD).
date: 2002/12/31 02:21:31; author: dsainty;
Be somewhat more persuasive about enabling the port on a port reset.
USB protocol dictates that the port enable must be implied by the port
reset. To implement this on (at least) the VIA VT83C572 this means we
need to wait around tweaking the chip state until the port actually
transitions to enabled (or the device goes away). Likely fixes
kern/11018.
get a Hub descriptor, we have to set req.wValue to "Descriptor Type
and Descriptor Index". In this case, Descriptor Type is 0x29
(UDESC_HUB), Descriptor Index should be 0.
If I don't do a check (dev->address > 1 ... ), root hub fails.
A new Cytronix 4-port USB 2.0 Hub (Cypress CY7C65640 chip) now works
after this patch.
Submitted by: Alexander Pohoyda <alexander.pohoyda@gmx.net>
MFC after: 7 days
64-bit counters that wrap on overflow. They are collecte once per
second from the chips. Currently they can be retrieved via a sysctl phy_stats.
A write of an arbitrary value to the sysctl atomically retrieves the
statistics and clears them.
* Use ACPI_BUFFER as the type for AcpiGetObjectInfo
* Remove AcpiEnableEvent/AcpiClearEvent for ACPI_EVENT_FIXED (power/sleep
buttons) as they are no longer needed
* Change calls to use the new GPE functions
* Add AcpiOs*Lock functions
Even if we have no AT keyboard, an AT keyboard is registered because
it's probed with KB_CONF_PROBE_ONLY flag set during console initialization.
Unregister the keyboard if it doesn't present while second probe.
This should fix USB keyboard only case without 'kbdcontrol -k /dev/kbd1'.
(mainly the 3Com 3c996B/BCM5701).
For some reason that I don't fully understand, the 5701 signals PCS
encoding errors as though they were link change events, i.e. the 'link
state changed' bit in the status word of the status block is updated
and an interrupt is generated. This would cause the bge_tick() function
to be invoked and a "gigabit link up" message to be printed on the console.
To avoid this, the interrupt handler now checks the MAC status register
when a link change interrupt is triggered, and it will only call the
bge_tick() function if the 'PCS encoding error detected' bit is clear.
(This change should have no effect on copper NICs since this bit can
only ever be set in TBI mode. I do not know how it affects 5704 NICs
with a BCM8002 SERDES PHY.)
Special thanks to: Sherry Rogers at UCB for allowing me access to one
of their traffic monitor boxes so I could diagnose this problem.
- MN-110 10/100 USB ethernet (ADMtek Pegasus II, if_aue)
- MN-120 10/100 cardbus (ADMtek Centaur-C, if_dc)
- MN-130 10/100 PCI (ADMtek Centaur-P, if_dc)
Also update dc(4) man page to mention support for MN-120 and MN-130.
* Always use polled mode. The intr approach did not work for many
controllers and required the hw.acpi.ec.event_driven workaround.
* Only use an edge (not level) triggered GPE handler
* Add sc->ec_mtx for locking operations to a single EC. There were
many race conditions earlier between an SCI event and EcRead/Write.
* Use 1 ms as the global lock timeout
* Only acquire global lock if _GLK != 0
* Update EcWaitEvent to use an incremental backoff delay in its
poll loop. Wait 50 ms max instead of 10. Most ECs respond
in < 5 us (50 us when heavily loaded). However, some time out
occasionally even with a 10 ms timeout. For delays past 1 ms, use
msleep instead of DELAY to give SCI interrupts a chance to occur.
* Add EcCommand to send a command and wait for the appropriate event.
* The hw.acpi.ec.event_driven tunable is no longer applicable and
has been removed.
Ideas from: Linux
bus_dma_tag_create. We need to be sure that our packets are
kept in-sequence (that's how ATM is supposed to work) and
therefor use BUS_DMA_NOWAIT in all calls to bus_dmamap_load.
For memory allocated with bus_dmamem_alloc the use of anything
other than NULL arguments for the locking is anyway bogus because
this memory never should need bouncing and hence the load should never
be defered.
Allow the receipt of OAM and RM cells on raw connections. Caveat: it seems
that RM cells are still processed by the hardware even when we open the
connection as UBR.
extra trailing space.
- Don't bother probing a generic ISA bus device if isab0 already exists.
Some BIOSes place an ACPI psuedo-device with the HID of a generic ISA bus
device under the PCI-ISA bridge device. This is not the best solution
but will work for now. The isa bus driver only allows for one ISA bus
anyways.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
- Factor out code common to all ISA bridge drivers attach methods into a
isab_attach() function.
- Rename the PCI-ISA bridge driver's attach function to pci_isab_attach()
and have it call isab_attach().
the bulk out buffer size to 16 bytes. The bulk out endpoint descriptor
reports 32 bytes, but if you use this value, data will get dropped.
Reviewed/approved by: scottl
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
tested for playback.
* modify device name strings for ich chips to better conform with their
common names.
* remove superflous 'AC97 controller' from nforce device names.
MFC after: 1 week
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
However, they are presently necessary due to bigger bogusness in the
pci bus layer not doing the right thing on suspend/resume or on
initial device probe. This is exactly the sort of thing that the
BURN_BRIDGES option was invented for. Mark all of them as
BURN_BRIDGES. As soon as I have the powerstate stuff properly
integrated into the pci bus code, I intend to remove all these
workarounds.
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
careful to call all map_load calls with BUS_DMA_NOWAIT because we
really don't want some PDUs to wait while others go out - ATM guarantees
the ordering of cells and also of PDUs (within one VC, that is). With
BUS_DMA_NOWAIT bus_dmamap_load should never return EINPROGRESS.
Make the tag used for transmission buffers one larger than the maximum
AAL5 PDU (65535). This is needed, because all PDU sizes need to be round
up to multiple of four for the card and PDUs that are just below the
maximum size will be rounded up to 65536
real SATA disks now that I can test it.
Add support for the SiI 3112 SATA chip using memory mapped I/O.
Update the support for the SiI 0680 to use the memio interface as well.
Sponsored by: David Leimbach <leimy2k@mac.com> (3112 based controller)
Sponsored by: FreeBSD Systems (www.FreeBSDsystems.com) (SATA disks)
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
interrupt to be used for a device. This is intended solely for internal
use of PCI bus implementations, and exists so that PCI bus drivers
implementing special interrupt assignment methods which require
additional work at the bus level to work right can be easily derived
from the generic driver (or any other one) without resorting to hacks.
It will be used in the sparc64 ofw_pcibus driver, which will be
committed shortly.
Make use of this method in the generic implementation, and add it to
the method table of bus drivers derived from the PCI one.
Reviewed by: imp, -hackers
are some Sun PCI devices around which bogusly set intpin to 0, although
they use the intline mechanism; this allows the device driver to correct
that.
Reviewed by: imp
- Initialize fc->status to process bus reset correctly after resume.
- Initialize AT ring buffer pointer.
- Requeue stdma to stfree for active IR buffer.
- Stop DMA before suspend for safe.
- Set powerstate after resume.
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
to store an int in the bio->bio_driver1 (a void *). It is big enough,
but you have to match the int sizes first before doing the cast.
Glanced at by: scottl
software crypto device:
o record crypto device capabilities in each session id
o add a capability that indicates if the crypto driver operates synchronously
o tag the software crypto driver as operating synchronously
This commit also introduces crypto session id macros that cleanup their
construction and querying.
channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
o add back rx monitor support
o make WI_RID_SCAN_RES DTRT
o fix a bug handling zero-length RID requests (used by dstumbler to set
a zero-length SSID)
o make RID_SCAN_REQ DTRT
o add back WI_RID_OWN_SSID
o fix wi_scan_ap to take a channel mask and txrate (for prism cards)
These changes fix dstumbler -o (monitor mode). A minor change to dstumbler
is needed to get normal AP scanning mode to work right; this is preferred to
modifying the driver.
PR: kern/53187
Reviewed by: Bruce M Simpson <bms@spc.org>
flag'ed INTR_MPSAFE. In ep_if_start(), use the IF_DEQUEUE macro to
grab the next mbuf to send, and use IF_PREPEND if the card is busy
and we actually can't handle it right now.
The old code was first getting the mbuf by taking it from the queue
without using the macros, thus without locking, and without removing
it from the queue either. It was later assuming that IF_DEQUEUE would
give him this same mbuf.
Tested by: mich
when the user specifies a maximum fragment size < 2.
This is the behavior that Linux provides and fixes the problem I've
observed in Tribes2 where sounds effects are delayed by 1/2 a second.
so can leave stale data in the buffer and confuse the driver.
- enable the ability to set the 'disable' hint for the driver to keep it
from attaching. i.e. 'hw.ips.0.disable=1' will prevent the driver from
attaching.
- Only detach if attach suceeded.
Submitted by: mjacob
in the netisr case. This would result in a lock reversal. This
fixes the net.isr.enable=1 case. Better performance might be
obtained by chaining all packets received, dropping the lock, and
then calling if_input() on each one.
Reported by: hmp
of the contents of the CCSCBCTL register into our
local varaible. The other bits are used in later tests.
This avoids a potential deadlock in ahd_run_qoutfifo()
if we happen to catch the DMA engine in just the right
state.
read permision only required for listing, read/write required for
read/write to registers
fix a possible memory leak
clean up error handling a bit
Reviewed by: silence
Reorder how the pci probing in handled. before adding devices, check to
see if the slot is a multi-function device to see if we should probe all
the functions.
Original idea by: imp
drivers that implemnt the i2c bit banging bus interface not have to
recompile iicbb in order to add an attachment for it.
This will mean the bktr and other definitions can go back to their
respective drivers.
- Mark that it cannot handle greater than 4GB of RAM at this time. Fixing
that will come later. Fail any attempts to dump above thati limit.
- If a call to aac_disk_dump() needs to be split into multiple i/o's,
increment the virtual offset after each i/o instead of just dumping the
same offset over and over again.
- Bail out if bus_dmamap_load() returns an error. Error recovery is likely
not possible.
This version of the driver code is compatible with near-release FreeBSD 5.1
kernel/driver interfaces.
modules/Makefile, man page and other bindings to follow shortly, once I get
this part of the check-in right.
Approved by: markm(mentor)
Previously, any normal I/O on an fdc(4) device would fail with ENXIO
if the device had been opened in non-blocking mode and then closed
prior to the conventional access; that would last until the floppy
disk was ejected and re-inserted to raise the unit attention condition.
Add a clarifying comment.
populated. Apparently, if you use an ehci controller, it's not.
Use usbd_device2interface_handle() to retrieve the interface handle.
NOTE: uaa->iface is populated in the probe routine, so I suspect the
fact that it's NULL in the attach routine is a bug in the ehci driver.
Also, don't depend on the PHY addresses returned by the AXE_CMD_READ_PHYID
command. The address is correct for my LinkSys NIC, but a user has
reported that with a D-Link NIC, the PHYID command returns address 4
while the attached Broadcom PHY is in fact strapped for address 0.
Instead, latch onto the first PHY address that returns valid data
during a readreg operation.
as should every block device strategy routine.
There was at least one evil consequence of not doing so:
Some errors returned by fdstrategy() could be lost (EAGAIN,
in particular.)
PR: kern/52338 (in the audit-trail)
Discussed with: bde
to access floppy parameters through it.
Note: The DIOCGSECTORSIZE and DIOCGMEDIASIZE handlers withing
fdioctl() couldn't be just moved to below the existing check
for blocking mode because fd->ft can be non-NULL while still
in non-blocking mode (fd->ft can be set with the FD_STYPE ioctl.)
PR: kern/52338
No MFC: Not applicable to STABLE
ulpt_status() afterwards. This fixes a crash that can occur if a
USB printer is power-cycled when printing is just starting. The
problem is similar to that fixed in revision 1.33, but it is much
less likely to occur.
MFC after: 1 week
and return NULL.
vinum_scandisk: Don't handle NULL device pointers.
Only look at compatibility partition for i386. This
is a kludge which should go away once I have adequate
documentation for the New World Order.
Together, these fixes remove occasional error messages about
non-existent drives. They may also fix a number of problems that have
been reported without a PR.
PRs: None
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
how we registered pccard_intr, it is MPSAFE. However, since we
register the pccard_intr handler with the flags of the ISR we call,
that is the gating factor. We need do nothing specific here.
Prompted by: seeing pccard_intr in a panic.
are the same that those of the kernel in the KLD_MODULE case. If
we ever want to detect that kind of problems, this is not the right
place to do this since every network driver would be affected by
such desynchronisation.
toggle several media options (sonet/sdh, for example) with ifconfig and
to see the carrier state in ifconfig's output. It gives also read/write
access (given the right privilegs) to the S/Uni registers to user space
programs.
than once. This appears to work around the hanging issues, at the
expense of warnings about bad RID allocations. I'm not sure this is a
permanant workaround, but does appear to help in the tests that I've
done here.
It currently supports the PMC Sierra Lite, Ultra and 622 chips and
the IDT 77105. The driver handles media options and state in a consistent
manner for ATM drivers. The next commit to the midway driver will make
it use utopia.
doesn't have one. The test was bogus on these architectures, but
recent changes broke it altogether.
Prompted by: phk
This should fix the recent SPARC 64 build problems.
o Register ISR INTR_MPSAFE.
o Loop on KTHREAD_DONE == 0 in the thread.
o Safe the INTR_MPSAFE flag for client drivers (don't know if there are any
CardBus/PCI drivers that are INTR_MPSAFE)
o Read status after acquiring mtx_lock(Giant) rather than before so that we
catch state changes that happen while Giant is being acquired.
o Turn off the CD bit when we see a CD interrupt, and turn it back on after
we've attached/detached the card.
o On suspend, actually set the CBB_SOCKET_MASK to zero rather than oring
in '0' to turn it off on suspend.
o If the ISR that's registerd is MPSAFE, don't acquire Giant around call to
client ISR.
o Fix comments to reflect these changes.
ia64-specific.
- When trying to re-route interrupts, don't change cfg->intline if the
re-route fails by returning an invalid vector. This fixes machines
without any way of routing interrupts such as older PC's without a
$PIR table.
We do not currently write the new intline value back to the hardware, but
we should. That will likely be added in a later commit.
if it was already enabled. We don't want to set it
when it shouldn't be set, we just don't want to
inadvertantly turn it off. This should fix a recent
report of the aic7xxx driver repeatedly complaining of
"unexpected busfree while idle" in one configuration.
successfully mapping our registers. This
avoids the disabling of memory mapped I/O
just because some other driver probe happened
to touch our registers.
This drive delays going async after receiving a WDTR
message. We now send an SDTR message after a WDTR even
if our goal is to go async. This should work even for
confused devices.
If we get an unexpected busfree when attempting a WDTR
or SDTR, only set the goal negotiation parameters we were
trying to negotiate to off. This means that should a WDTR
message fail, we will still try an SDTR if our goal is
non-async.
Fix a few more places where we were looking at goal.period
instead of goal.offset for determining if we should be
negotiating sync. This should not have any impact on
our behavior, but the offset is more definitive and should
be used.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
aic7xxx.c:
aic7xxx.h:
aic7xxx_pci.c:
Switch ah?_reset() to take an additional "reinit" argument.
Use this instead of init_level to determin if the chip
should be fully reinitialized after a chip reset. This
is required so that ah?_shutdown() can reset the chip
without side-effects.
aic79xx.c:
Implement ahd_suspend() and ahd_resume().
aic7xxx.c:
Change ahc_loadseq() to *not* restart the sequencer.
This brings the loadseq behavior in line with that
of the 7902 driver and also simplifies the init routine.
Correct the resume routine to enable interrupts and
restart the sequencer.
obtained from o2micro. These should only be needed for 'older'
o2micro bridges (anything before the 7xxx series of bridges), but will
work with the new bridges.
# I don't plan on porting it to oldcard, but will happily commit to
# oldcard if someone else needs them.
Add sysctl's to display statistics/debug_info
Set WAIT_FOR_AUTONEG_DEFAULT to zero by default
Increment packet in/out statistics inline instead of every two seconds.
MFC after: 3 days
Always route PCI interrupts on i386 UP machines. I was planning to enable
this for i386 anyways once SMP support is done. Having this enabled fixes
problems on many people's laptops.
Requested by: imp
While a string is readable without a tool, an array is easier to process for
a monitoring application. This also prevents the extra hoops we need with
sbufs and locking.
Move the mtx_init() in en_attach() higher before the first failure point so
that we can unconditionally destroy it in en_destroy().
to unload. This would cause a panic on the second resetconfig.
Start Vinum at boot time at SI_SUB_RAID, not SI_SUB_VINUM.
SI_SUB_VINUM was there first, but there's no real distinction, and
SI_SUB_RAID is a more neutral name.
Submitted by: hmp
o adding locking to op submission
o mark interrupt handler MPSAFE
o don't use locking on detach; disabling interrupts should be sufficient
o change mutex string names so witness printouts are more meaningful
Note: locking is still pretty brute-force but it's probably not worth
improving it given the relatively low performance of hifn-based cards.
o replace driver-global lock with three locks: one for the handling of mcr1
operations, one for handling of mcr2 operations, and one for the mcr1
free list
o mark the interrupt handler MPSAFE
o don't use locking on detach; disabling interrupts is sufficient (I think)
Change the list interface to simplify things.
Remove old list ioctls which bogusly exported the softc to userland.
Move the softc and associated structures from the public header to
the source file.
Make CCD a GEOM class.
For now only use this for implementing a OAM config method which
can return a list of configured CCD devices in the format which
"ccdconfig -g[v]" would normally output.
bzero(ptr, sizeof(DC_RXLEN * 5));
which should obviously be:
bzero(ptr, DC_RXLEN * 5);
Looks like this bug may have reduced the effectiveness of the
workaround for the hardware bug in the PNIC chips.
MFC after: 1 week
o Remove register keyword
o ANSIfy prototypes
o Remove "return;" at the end of void functions
o Remove trailing spaces
o Don't align local variables with tabs and reorder them
o Don't use /* FOO */ at the end of a #ifdef FOO block if
it's a small block
- Other non-functional changes :
o 6 -> ETHER_ADDR_LEN
o Don't initialize if_output; ether_ifattach() does it for us
