ixgbe driver. As it was, when building them as a module INET
and INET6 are not defined. In these drivers it does not cause
a panic, however it does result in different behavior in the
ioctl routine when you are using a module vs static, and I
think the behavior should be the same.
MFC after: 3 days
MFprojects/camlock r248982:
Stop abusing xpt_periph in random plases that really have no periph related
to CCB, for example, bus scanning. NULL value is fine in such cases and it
is correctly logged in debug messages as "noperiph". If at some point we
need some real XPT periphs (alike to pmpX now), quite likely they will be
per-bus, and not a single global instance as xpt_periph now.
when building the driver as a module the result of the present
system results in INET and INET6 being undefined, and will cause
the panic in ixgbe_tso_setup(). The Makefile in the module directory
now renders the conditional in the source unnecessary and wrong.
MFC after: ASAP - the panic as a module must not get into 9.2
processing. Thanks for John Baldwin for catching this. Not
clearing the flag member of the rxbuf could result in a NULL
mbuf pointer being used.
MFC after: 2 days (this needs to get into 9.2!)
H/W not de-asserting the interrupt at all. On x86, and because of the
following conditions, this results in a hard hang with interrupts disabled:
1. The uart(4) driver uses a spin lock to protect against concurrent
access to the H/W. Spin locks disable and restore interrupts.
2. Restoring the interrupt on x86 always writes the flags register. Even
if we're restoring the interrupt from disabled to disabled.
3. The x86 CPU has a short window in which interrupts are enabled when the
flags register is written.
4. The uart(4) driver registers a fast interrupt by default.
To catch this case, we first try to clear any pending H/W interrupts and in
particular, before setting up the interrupt. This makes sure the interrupt
is masked on the PIC. The interrupt handler now has a limit set on the
number of iterations it'll go through to clear interrupt conditions. If the
limit is hit, the handler will return FILTER_SCHEDULE_THREAD. The attach
function will check for this return code and avoid setting up the interrupt
and foce polling in that case.
Obtained from: Juniper Networks, Inc.
structure copying in random_ident_hardware(). This change will also help
further modularization of random(4) subsystem.
Submitted by: arthurmesh@gmail.com
Reviewed by: obrien
Obtained from: Juniper Networks
VMware up to at least ESXi 5.1. Actually, using INTx in that case instead
may still result in interrupt storms, with MSI being the only working
option in some configurations. So introduce a PCI_QUIRK_DISABLE_MSIX quirk
which only blacklists MSI-X but not also MSI and use it for the VMware
PCI-PCI-bridges. Note that, currently, we still assume that if MSI doesn't
work, MSI-X won't work either - but that's part of the internal logic and
not guaranteed as part of the API contract. While at it, add and employ
a pci_has_quirk() helper.
Reported and tested by: Paul Bucher
- Use NULL instead of 0 for pointers.
Submitted by: jhb (mostly)
Approved by: jhb
MFC after: 3 days
of Skyhawk adapters.
Many thanks to Emulex for their continued support of FreeBSD.
Submitted by: "Duvvuru,Venkat Kumar" <VenkatKumar.Duvvuru Emulex.Com>
MFC after: 1 day
full issue with ARC-1214 and ARC-1224.
Many thanks to Areca for continuing to support FreeBSD.
Submitted by: 黃清隆 <ching2048 areca com tw>
MFC after: 1 day
user, where when more than one hpt27xx adapters are being used,
the "unit number" stays at 0.
Many thanks to HighPoint for providing this driver update.
MFC after: 1 day
controllers. Update the hptiop(4) manual page to reflect this
as well as mentioning that some cards are already end-of-life.
Many thanks to Highpoint for providing this driver update.
MFC after: 1 day
/dev/kmem and /dev/mem (in addition to traditional file permission checks).
PRIV_KMEM_READ is different from other PRIV_* checks in that it's allowed
by default.
Reviewed by: kib, mckusick
when the interface is up.
- Add a tunable to control the TOE's rx coalesce feature (enabled by
default as it always has been). Consider the interface MTU or the
coalesce size when deciding which cluster zone to use to fill the
offload rx queue's free list. The tunable is:
dev.{t4nex,t5nex}.<N>.toe.rx_coalesce
MFC after: 1 day
* Add 802.11n 2ghz and 5ghz tables, including legacy rates and up to
MCS23 rates (3x3.)
* Populate the rate code -> rate index lookup table with MCS _and_
normal rates, but _not_ the basic rate flag. Since the basic rate flag
is the same as the MCS flag, we can only use one.
* Introduce some accessor inlines that do PLCP and rate table lookup/access
and enforce that it doesn't set the basic rate bit. They're not
designed for MCS rates, so it will panic.
* Start converting drivers that use the rate table stuff to use the
accessor inlines and strip the basic flag.
* Teach AMRR about basic 11n - it's still as crap for MCS as it is
being used by iwn, so it's not a step _backwardS_.
* Convert iwn over to accept 11n MCS rates rather than 'translate' legacy
to MCS rates. It doesn't use a lookup table any longer; instead it's a
function which takes the current node (for HT parameters) and the
rate code, and returns the hardware PLCP code to use.
Tested:
* ath - it's a no-op, and it works that way
* iwn - both 11n and non-11n
It's not enabled by default in net80211 so this is a no-op unless
if you enable it (ifconfig wlan0 powersave).
Tested:
* iwn0: <Intel WiFi Link 5100> mem 0xf4300000-0xf4301fff irq 17 at device 0.0 on pci3
TODO:
* .. test on all the other NICs
* See if I have to disable it during scan and such
* Make it configurable live, rather than only after it's done its initial
receive calibration.
r252680:
Fix SIM lock not owned panic
The CAM locking requirements of registering an async
callback has changed so the SIM lock must be held. Remove
code that explicitly dropped the lock around the register.
Also return CAM_SEL_TIMEOUT instead of CAM_TID_INVALID
for bad targets to avoid a lot console spam during bus
scans.
MFC after: 1 month
This commit is primarily a significant cleanup to the interrupt
allocation code that had gotten a bit jumbled from having to
support per-vq MSIX, shared MSIX, MSI, and legacy style interrupts.
Contains projects/virtio commits:
r246064:
virtio_pci: Rewrite allocation of interrupts
r246065:
virtio_pci: Remove spaces before a tab
r246066:
virtio_pci: Dynamically allocate the virtqueue array
r246304:
virtio_pci: Clean up after failed virtqueue alloc attempt
r246305:
virtio_pci: Move no interrupt check into the PCI interrupt handlers
r246308:
virtio_pci: Remove unused variable
MFC after: 1 month
Minor changes to the network driver. A multiqueue driver that is
a significant rewrite will be in merged shortly.
Contains projects/virtio commits:
r246058:
vtnet: Move an mbuf ASSERT to the calling function
r246059:
vtnet: Tweak ASSERT message
MFC after: 1 month
Contains projects/virtio commits:
r245717:
virtio_balloon: Make the softc lock a regular mutex
r245718:
virtio_balloon: Remove two unuseful ASSERTs
r245719:
virtio_balloon: More verbose ASSERT messages
r245720:
virtio_balloon: Simplify lowmem handling in vtballoon_inflate()
r252530:
virtio_balloon: Use just a kthread instead of dedciated kproc
r252568:
virtio_balloon: Need to use kthread_exit() after r252530
MFC after: 1 month
The notable changes of this commit are support for disk resizing
and chases updates to the spec regarding write caching.
Contains projects/virtio commits:
r245713:
virtio_blk: Replace __FUNCTION__ with __func__
r245714:
virtio_blk: Use more consistent mutex name
r245715:
virtio_blk: Print device name too if failed to reinit during dump
r245716:
virtio_blk: Remove an unuseful ASSERT
r245723:
virtio_blk: Record the vendor and device information
r245724:
virtio_blk: Add resize support
r245726:
virtio_blk: More verbose ASSERT messages
r245730:
virtio_blk: Tweak resize announcement message
r246061:
virtio_blk: Do not always read entire config
r246062:
virtio_blk: Use topology to set the stripe size/offset
r246307:
virtio_blk: Correct stripe offset calculation
r246063:
virtio_blk: Add support for write cache enable feature
r246303:
virtio_blk: Expand a comment
r252529:
virtio_blk: Improve write cache handling
r252681:
virtio_blk: Remove unneeded curly braces
MFC after: 1 month
Contains projects/virtio commits:
r245709:
Each VirtIO device was scheduling its own taskqueue(9) to do the
off-level interrupt handling. ithreads(9) is the more nature way
to do this. The primary motivation for this work to better support
network multiqueue.
r245710:
virtio: Change virtqueue intr handlers to return void
r245711:
virtio_blk: Remove interrupt taskqueue
r245721:
vtnet: Remove interrupt taskqueue
r245722:
virtio_scsi: Remove interrupt taskqueue
r245747:
vtnet: Remove taskqueue fields missed in r245721
MFC after: 1 month
