This alleviates issues on newer Sandy/Ivy Bridge gear that seems to require
boatloads more ACPI resources than before.
Reviewed by: avg@
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
This happens during a scan in STA mode; any queued data frames will
be power save queued but as there's no TIM in STA mode, it panics.
This was introduced by me when I disabled my driver-aware power save
handling support.
actual traffic with an AR9380/AR9382/AR9485.
The sample rate control stats would show impossibly large numbers for
"successful packets transmitted." The number was a tad under 2^^64-1.
So after a bit of digging, I found that the sample rate control code
was making 'tries' turn into a negative number.. and this was because
ts_longretry was too small.
The hardware returns "ts_longretry" at the current rate selection,
not overall for that TX descriptor. So if you setup four TX rate
scenarios and the second one works, ts_longretry is only set for
the number of attempts at that second rate scenario. The FreeBSD HAL
code does the correction in ath_hal_proctxdesc() - however, this isn't
possible with EDMA.
EDMA TX completion is done separate from the original TX descriptor.
So the real solution is to split out "find ts_rate and ts_longretry"
from "complete TX descriptor". Until that's done, put a hack in
the EDMA TX path that uses the rate scenario information in the ath_buf.
Tested: AR9380, AR9382, AR9485 STA mode
in nve(4). The OS_API structure defined in os.h expects NV_API_CALL
attributes, effectively regparm(0), on its function pointers, but all
the functions were declared and defined without this attribute.
MFC after: 1 week
DWC OTG driver. Fix a hang issue when using LOW and FULL speed
BULK traffic. Make sure we don't ask for data in the last
microframe. This allows using devices like USB mice and USB
keyboards connected to the RPI-B.
Suggested by: gonzo @
events.
This is primarily for the TX EDMA and TX EDMA completion. I haven't yet
tied it into the EDMA RX path or the legacy TX/RX path.
Things that I don't quite like:
* Make the pointer type 'void' in ath_softc and have if_ath_alq*()
return a malloc'ed buffer. That would remove the need to include
if_ath_alq.h in if_athvar.h.
* The sysctl setup needs to be cleaned up.
I'm using this to debug EDMA TX and RX descriptors and it's really helpful
to have a non-printf() way to decode frames.
I won't link this into the build until I've tidied it up a little more.
This will eventually be behind ATH_DEBUG_ALQ.
kernel memory leakage to userspace. For the typical use, when a
filesystem put on the md disk, the change only results in CPU and
memory bandwidth spent to zero the page, since filsystems make sure
that user never see unwritten content. But if md disk is used as raw
device by userspace, the garbage is exposed.
Reported by: Paul Schenkeveld <freebsd@psconsult.nl>
MFC after: 2 weeks
ps-poll is totally broken in its current form.
This should unbreak things enough to let people use PS-POLL devices,
but leave it in place for me to finish PS-POLL handling.
function use that for JBOD and Thunderbolt disk write command. Now
we only have one implementation in mfi.
- Fix dumping on Thunderbolt cards. Polled IO commands do not seem to
be normally acknowledged by changing cmd_status to MFI_STAT_OK.
In order to get acknowledgement of the IO is complete, the Thunderbolt
command queue needs to be run through. I added a flag MFI_CMD_SCSI
to indicate this command is being polled and to complete the
Thunderbolt wrapper and indicate the result. This flag needs to be
set in the JBOD case in case if that us using Thunderbolt card.
When in the polling loop check for completed commands.
- Remove mfi_tbolt_is_ldio and just do the check when needed.
- Fix an issue when attaching of disk device happens when a device is
already scheduled to be attached but hasn't attached.
- add a tunable to allow raw disk attachment to CAM via:
hw.mfi.allow_cam_disk_passthrough=1
- fixup aborting of commands (AEN and LD state change). Use a generic
abort function and only wait the command being aborted not both.
Thunderbolt cards don't seem to abort commands so the abort times
out.
counter) when the syncache doesn't want the driver to reply to an
incoming SYN. This fixes a harmless bug where tids_in_use would
go out of sync with the hardware counter.
MFC after: 3 days
the non-aggregate path.
I "cheated" by using some TX setup code in our HAL that isn't present
in the atheros HAL (or Linux ath9k.)
The old path for forming aggregates was:
* setup the rate control in the first descriptor;
* call chaintxdesc() on all the frames;
* call setupfirsttxdesc() on the first descrpitor in the first
frame;
* call setuplasttxdesc() on the last descriptor in the last frame.
The new path for forming aggregates looks like the non-aggregate path:
* call setuptxdesc() on the first descriptor in the first frame;
* setup the rate control in the first descriptor;
* call filltxdesc() on each descriptor in the frame;
* if it's an aggregate - call set11n_aggr_{first, middle, last} as
appropriate (see the code for a description of what is "appropriate".)
Now, this is done primarily for the AR9300 HAL - it doesn't implement
the first set of aggregate functions. It just has the older methods
and the "first/middle/last" aggregate methods. So, let's convert the
code to use these.
Note: the AR5416 HAL in FreeBSD had that code (from me, a while ago)
and a previous commit brought it up to behave the same as the AR9300
HAL routines.
There's some further tidyups to be done - specifically, avoid doing
multiple calls to the 11n descriptor functions. I shouldn't call
clr11n_aggr(), then set11n_aggr_middle(), then also set11n_aggr_first().
On (at least MIPS) the TX descriptors are in non-cachable memory and
this will cause multiple slow writes.
I'll debug/tidy that up in a future commit.
Tested:
* AR9280, STA
* AR9280/AR9160, AP
* AR9380, STA (using a local, closed source HAL, sorry!)
the 'PREVENT/ALLOW MEDIUM REMOVAL' SCSI command. An example of such a
device is the STmicro ST72682. We send the SCSI command for every open and
close, which can result in a significant amount of spam on the console
during boot.
Reviewed by: hps@
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
Reviewed by: yongari, marius
MFC after: 1 week
temporarily stores characters if the TTY buffer is full when
used a as a console. This can happen when a console is suspended.
Also properly do the flow stop signalling when this happens and
flow start when the condition changes back to normal again.
Bump __FreeBSD_version to force external kernel modules
to be recompiled. No kernel API changes.
MFC after: 1 week
Suggested by: ed @
PNP0510 and FUJ02E5 for a "Wacom Tablet at FuS Lifebook T"
PNP0502 and PNP0511 for some other generic devices.
PR: kern/173357
Submitted by: Andrey Zakharchenko <avz@jscc.ru>
Approved by: cperciva (implicit)
MFC after: 1 week
