The PRM suggests random 0 - 10ms to prevent multiple waiters on the same
interval in order to avoid starvation.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Linux commits:
6c780a0267b8
b8a92577f4be.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in mlx5core. The EEPROM information is not only a property of the
mlx5en(4) driver.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
All prints in mlx5core should use on of the macros:
mlx5_core_err/dbg/warn
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
In case of health counter fails to increment it indicates a bad device health.
In case when the syndrome indicated by firmware is 0x0, this indicates that
firmware is unable to respond to initialization segment reads.
Add proper print in this case.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
MPFS is a logical switch in the Mellanox device which forward packets
based on a hardware driven L2 address table, to one or more physical-
or virtual- functions. The physical- or virtual- function is required
to tell the MPFS by using the MPFS firmware commands, which unicast
MAC addresses it is requesting from the physical port's traffic.
Broadcast and multicast traffic however, is copied to all listening
physical- and virtual- functions and does not need a rule in the MPFS
switching table.
Linux commit: eeb66cdb682678bfd1f02a4547e3649b38ffea7e
MFC after: 3 days
Sponsored by: Mellanox Technologies
There is no reason to re-create the command workqueue during healthcare.
This also fixes an issue where a previous work struct may refer to a
destroyed workqueue.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Present code uses lock-less accesses to the dump data to prevent top
level ioctls from blocking bottom-level call to dump. Unfortunately, this
depends on the type stability of the dump data structure, which makes it
non-functional during driver teardown.
Switch to the mutex locking scheme where top levels use the mutex in the
bound regions, while copyouts and drain for completion utilize condvars.
The mutex lifetime is guaranteed to be strictly larger than the time
interval where driver can initiate dump, and most of the control fields
of the old struct mlx5_dump_data are directly embedded into struct
mlx5_core_dev.
Submitted by: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid race for command completion when triggering a command completions event.
Serialize operation by queueing all commands on the same work queue.
This can happen when healthcare triggers.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Implement a watchdog as part of the healtcare subsystem which
reads the PCI power status during startup and upon the PCI
power status change event and store it into the core device
structure. This value is then exported to user-space via a
read-only SYSCTL. A dmesg print has been added to inform
the admin about the PCI power status.
MFC after: 3 days
Sponsored by: Mellanox Technologies
mlx5_pci_disable_device is calling pci_disable_device which disables
bus master. No need to explicitly call pci_clear_master.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add mlx5 implementation for the ones defined by the mlxfw
shared module to be used while flashing the device firmware.
The callbacks do their job through the MCQI, MCC and MCDA registers.
Linux commit:
62bd22cf326dc4ac5be673c11cef4602dc1f5e47
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
To be used by the mlx5 callbacks exposed to the mlxfw module.
Linux commit:
d2ad488b0073bd1a2c3f5d2ea50a7eb632103e5d
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
On load_one, we now cache our capabilities registers internally, similar
to QUERY_HCA_CAP. Capabilities can later be queried using macros
introduced in this patch.
Linux commit:
71862561f3a62015a11de16d1c306481e8415c08
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Introduced registers will expose capabilities of new registers and
features related to port/management.
Driver will query MCAM and PCAM in order to avoid failing on old
firmwares with lack of support.
Linux commit:
c835ad64683bd3e2d1b31ed2cb1ff4366932edb1
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been
scattered to memory
Linux commit:
fcd29ad17c6ff885dfae58f557e9323941e63ba2
MFC after: 3 days
Sponsored by: Mellanox Technologies
