Currently the ifnet interface is named mceX, where X is a monotonically
incremented value. If the device is reset due to a fatal error, then the
interface name will change. Using the device unit number will keep the
naming consistent across the reset logic.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for PFC and implement reading the per priority statistics
using the sysctl(8) interface. PFC is used together with VLAN priority
and can be enabled and disabled on a per priority basis.
Global pause frames and PFC are incompatible features and surrounding
logic has been added to warn the user about misconfiguration.
Update relevant mlx5core APIs for PFC configuration.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
mlx5_health.c
- 78ccb25861d76a8fc5c678d762180e6918834200
mlx5_core: Fix wrong name in struct
- 171bb2c560f45c0427ca3776a4c8f4e26e559400
mlx5_core: Update health syndromes
- 0144a95e2ad53a40c62148f44fb0c1f9d2a0d1e9
mlx5_core: Use accessor functions to read from device memory
- ac6ea6e81a80172612e0c9ef93720f371b198918
mlx5_core: Use private health thread for each device
- fd76ee4da55abb21babfc69310d321b9cb9a32e0
mlx5_core: Fix internal error detection conditions
- 2241007b3d783cbdbaa78c30bdb1994278b6f9b9
mlx5: Clear health sick bit when starting health poll
- 712bfef60912d91033cb25739f7444d5b8d8c59f
mlx5: Fix version printout in case of health issue
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
mlx5_cmd.c
- be87544de8df2b1eb34bcb5e32691287d96f9ec4
mlx5_core: Fix async commands return code
- a31208b1e11df334d443ec8cace7636150bb8ce2
mlx5_core: New init and exit flow for mlx5_core
- 020446e01eebc9dbe7eda038e570ab9c7ab13586
mlx5_core: Prepare cmd interface to system errors handling
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
- 0d834442cc247c7b3f3bd6019512ae03e96dd99a
mlx5: Fix teardown errors that happen in pci error handler
mlx5_main.c
- 5fc7197d3a256d9c5de3134870304b24892a4908
mlx5: Add pci shutdown callback
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
accomplishes a few things:
- Makes NULL an invalid address in the kernel, which is useful for catching
bugs.
- Lays groundwork for radix-tree translation on POWER9, which requires the
direct map be at high memory.
- Similarly lays groundwork for a direct map on 64-bit Book-E.
The new base address is chosen as the base of the fourth radix quadrant
(the minimum kernel address in this translation mode) and because all
supported CPUs ignore at least the first two bits of addresses in real
mode, allowing direct-map addresses to be used in real-mode handlers.
This is required by Linux and is part of the architecture standard
starting in POWER ISA 3, so can be relied upon.
Reviewed by: jhibbits, Breno Leitao
Differential Revision: D14499
Add support for mapping priority to traffic class via sysctl
Submitted by: Slava Shwartsman <slavash@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Factor out port speed definitions into new port.h header file,
similarly as done in Linux upstream.
- Correct two existing port speed definitions in mlx5en according to
Linux upstream.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get firmware response. Add delayed callback timeout work
before posting the command to firmware. In case of real firmware
command completion we will cancel the delayed work. In case of
firmware command timeout the callback timeout handler will be called
and it will simulate firmware completion with timeout error.
linux commit 65ee67084589c1783a74b4a4a5db38d7264ec8b5
MFC after: 1 week
Sponsored by: Mellanox Technologies
Call command completion handler in case of timeout when working in
interrupts mode. Avoid flushing the commands workqueue after acquiring
the semaphores to prevent a potential deadlock.
linux commit commit 9cba4ebcf374c3772f6eb61f2d065294b2451b49
MFC after: 1 week
Sponsored by: Mellanox Technologies
band aid until a better solution to find the correct interrupt controller
can be found.
While here fix one place in the GICv3 ITS driver where the offset wasn't
correctly applied.
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
bus provide it with its needed memory resources.
This allows us to use PCIe on the ThunderX2 and, with a previous version
of the patch, on the SoftIron 3000 with ACPI.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D8767
This was tested by Ben on HP Chromebook 13 G1 with a
Skylake CPU and Sunrise Point-LP I2C controller and by me on
Minnowboard Turbot with Atom E3826 (formerly Bay Trail)
Submitted by: Ben Pye <ben@curlybracket.co.uk>
Reviewed by: gonzo
Obtained from: DragonflyBSD (a4549657 by Imre Vadász)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13654
Creating a UD address handle from user-space or from the kernel-space,
when the link layer is ethernet, requires resolving the remote L3
address into a L2 address. Doing this from the kernel is easy because
the required ARP(IPv4) and ND6(IPv6) address resolving APIs are readily
available. In userspace such an interface does not exist and kernel
help is required.
It should be noted that in an IP-based GID environment, the GID itself
does not contain all the information needed to resolve the destination
IP address. For example information like VLAN ID and SCOPE ID, is not
part of the GID and must be fetched from the GID attributes. Therefore
a source GID should always be referred to as a GID index. Instead of
going through various racy steps to obtain information about the
GID attributes from user-space, this is now all done by the kernel.
This patch optimises the L3 to L2 address resolving using the existing
create address handle uverbs interface, retrieving back the L2 address
as an additional user-space information structure.
This commit combines the following Linux upstream commits:
IB/core: Let create_ah return extended response to user
IB/core: Change ib_resolve_eth_dmac to use it in create AH
IB/mlx5: Make create/destroy_ah available to userspace
IB/mlx5: Use kernel driver to help userspace create ah
IB/mlx5: Report that device has udata response in create_ah
MFC after: 1 week
Sponsored by: Mellanox Technologies
of years since the century, so strip the century out when converting to or
from bcd_clocktime format (the conversion routines will infer century by
pivoting on 70).
the jtag port, so that a tty is not created for it.
This is based on information in the PR and from the vendor website. When
the PR was first opened we had no facility for flagging the jtag ports. I
stumbled across the still-open PR with the idea of closing it, and noticed
that this wee update was needed.
PR: 175893
imcsmb(4) provides smbus(4) support for the SMBus controller functionality
in the integrated Memory Controllers (iMCs) embedded in Intel Sandybridge-
Xeon, Ivybridge-Xeon, Haswell-Xeon, and Broadwell-Xeon CPUs. Each CPU
implements one or more iMCs, depending on the number of cores; each iMC
implements two SMBus controllers (iMC-SMBs).
*** IMPORTANT NOTE ***
Because motherboard firmware or the BMC might try to use the iMC-SMBs for
monitoring DIMM temperatures and/or managing an NVDIMM, the driver might
need to temporarily disable those functions, or take a hardware interlock,
before using the iMC-SMBs. Details on how to do this may vary from board to
board, and the procedure may be proprietary. It is strongly suggested that
anyone wishing to use this driver contact their motherboard vendor, and
modify the driver as described in the manual page and in the driver itself.
(For what it's worth, the driver as-is has been tested on various SuperMicro
motherboards.)
Reviewed by: avg, jhb
MFC after: 1 week
Relnotes: yes
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D14447
Discussed with: avg, ian, jhb
Tested by: allanjude (previous version), Panasas
In the weird case where the user-provided buffer was zero bytes, we could break
out of PCIOCGETCONF and return without initializing error. In this case,
initialize error to zero -- we successfully did nothing, as requested.
Reported by: Coverity
Sponsored by: Dell EMC Isilon
'status' array passed to get_mouse_status() is usually uninitialized by
callers.
Fully populating it with values in get_mouse_status() can fail due to
read_aux_data().
Additionally, nothing in API constrains 'len' to be >= 3. In practice,
every caller passes three, so perhaps that argument should just be removed.
Refactoring is a larger change, though.
Remove use of potentially uninitialized values by:
1. Only printing 3 debug statuses if the passed array was at least
'len' >= 3;
2. Populating 'status' array up to first three elements, if read_aux_data()
failed.
No functional change intended.
Reported by: Coverity
Sponsored by: Dell EMC Isilon
