It's still not ready for prime-time - there's some TX niggles with these 11n
cards that I'm still trying to wrap my head around, and AMPDU-TX is just not
implemented so things will come to a crashing halt if you're not careful.
"extended capabilities" to refer to the new set of capability structures
starting at offset 0x100 in config space for PCI-express devices. For now
both function names will still work. I will merge this to older branches
to ease driver portability, but 9.0 will ship with a new pci_find_extcap()
function that locates extended capabilities instead.
Reviewed by: imp
MFC after: 1 week
This fix modifies the const addac initval array, rather than modifying
a local copy. It means that running >1 AR9160 on a board may prove to
be unpredictable.
The AR5416 init path also does something similar, so supporting
>1 AR5416 of different revisions could cause problems.
The later fix will be to create a private copy of the Addac data
for the AR5416, AR9160 (and AR9100 when it's merged in) and then
modify that as needed.
Obtained From: Linux ath9k
I found this when trying to figure out why the RX PHY error count
didn't match the OFDM error count ANI was using. It turns out
there was two problems:
* What this commit addresses - using the wrong mask for OFDM errors,
and
* The RX filter is set incorrectly after a channel scan (at least)
even if interference mitigation is enabled by default.
ANI is still disabled by default for the AR5416 and later chips.
set as TCP.
- Eliminate the fully linear non-scatter/gather rx path, there is no
harm in using arrays of clusters for both TCP and UDP.
- Implement support for enabling/disabling per-vlan priority pause and
queues via sysctl.
bring it in line with the rest of the register initialisation.
I've verified that the 2/5ghz board values written to the
chip match what was previously written.
* add pspoll/uapsd queue setup defaults;
* enable the exponential backoff window rather than the random
backoff window when doing TX contention management.
would be a problem, make sure it isn't overwritten by whatever is in
there at cold reset.
This brings the > ar5416 init path treatment of AR_MISC_MODE.
report descriptor information, sysctl utility
will show it for us.
- Modify sysctl node description to make it more
understanable.
Found by: Alexander Best <arundel@freebsd.org>
Submitted by: Eygene Ryabinkin <rea@freebsd.org>
MFC after: 14 days
Approved by: thompsa (mentor)
value is updated after that we read it in the queue-head. This patch can
fix problems with BULK timeouts. The issue was found on a Nvidia chipset.
MFC after: 14 days
Approved by: thompsa (mentor)
services or PAL procedures. The new implementation is based on
specific functions that are known to be called in certain scenarios
only. This in particular fixes the PAL call to obtain information
about translation registers. In general, the new implementation does
not bank on virtual addresses being direct-mapped and will work when
the kernel uses PBVM.
When new scenarios need to be supported, new functions are added if
the existing functions cannot be changed to handle the new scenario.
If a single generic implementation is possible, it will become clear
in due time.
While here, change bootinfo to a pointer type in anticipation of
future development.
from another context at the moment of later access.
PR: kern/155555
Submitted by: Andrew Boyer <aboyer att averesystems.com>
Approved by: avg (mentor)
MFC after: 2 weeks
the topology mutex in the following functions, that manipulate pointers
to peer nodes:
- ng_bypass()
- ng_path2noderef() when switching to the next node in sequence.
Rewrite the function a bit.
- ng_address_hook()
- ng_address_path()
This patch improves stability of large mpd5 installations.
* Pull out the static rix stuff into a different function
* I know this may slightly drop performance, but check if a static
rix is needed before each packet TX.
* Whilst I'm at it, add a little extra debugging to the rate
control stuff to make it easier to follow what's going on.
1. The PBVM is in region 4, so if we want to make use of it, we
need region 4 freed up.
2. Region 4 and above cannot be represented by an off_t by virtue
of that type being signed. This is problematic for truss(1),
ktrace(1) and other such programs.
Give it a good go (32 attempts) and then print out a warning that's
going to occur whether HAL debugging is enabled or not. Then don't
abort the radio setup; just continue merrily along.
This should fix the issue that users were having where scanning would
occasionally fail on the active channel, causing traffic to cease
until the radio scanned again.
since before r127501. Strictly speaking, the buffer pages are not
"wired". They remain in the paging queues. However, they are pinned in
memory using vm_page_hold().
not needed.
These calibrations are only applicable if the chip operating mode
engages both interleaved RX ADCs (ie, it's compensating for the
differences in DC gain and DC offset -between- the two ADCs.)
Otherwise the chip reads values of 0x0 for the secondary ADC
(as I guess it's not enabled here) and thus writes potentially
bogus info into the chip.
I've tested this on the AR9160 and AR9280; both behave themselves
in 11g mode with these calibrations disabled.
for fixing them based on the ath9k related TXQ fixes.
I've done this so people can go over the history of the diffs to the original
AR5212 routines (which AR5416 and later chips use) to see what's changed.
enables broadcast filtering. Make sure to clear the bit to receive
broadcast frames. While I'm here rename the bit definition to
reflect reality.
Reported by: brad@OpenBSD
MFC after: 1 week
- A closer inspection of the OpenSolaris code indicates the block store
workaround is only necessary in case of BUS_DMASYNC_POSTREAD.
- Mark some unused parameters as such.
In some cases as udp6_connect() without an earlier bind(2) to an
address, v4-mapped scokets allowed and a non mapped destination
address, we can end up here with both v4 and v6 indicated:
inp_vflag = (INP_IPV4|INP_IPV6|INP_IPV6PROTO)
In that case however laddrp is NULL as the IPv6 path does not
pass in a copy currently.
Reported by: Pawel Worach (pawel.worach gmail.com)
Tested by: Pawel Worach (pawel.worach gmail.com)
MFC after: 6 days
X-MFC with: r219579
configurations and make it opt-in for those who want it. LINT will
still build it.
While it may be a perfect win in some scenarios, it still troubles users
(see PRs) in general cases. In addition we are still allocating resources
even if disabled by sysctl and still leak arp/nd6 entries in case of
interface destruction.
Discussed with: qingli (2010-11-24, just never executed)
Discussed with: juli (OCTEON1)
PR: kern/148018, kern/155604, kern/144917, kern/146792
MFC after: 2 weeks
