All the per-port support is really doing is applying a port visibility
mask to each of the switchports. Everything still look like a single
portgroup (vlan id 1), but the per-port visibility mask is modified.
Whilst I'm here, also add some initial dot1q support - the pvid stuff
is doing the right thing, but it's not useful without the rest of
the VLAN table programming.
It's enough for me to be able to use the LAN/WAN port distinction
on the AP135, where there isn't (for now!) a dedicated PHY for the
"WAN" port.
Tested:
* AP135, QCA9558 SoC + AR8327 switch
been done by U-Boot. This allows the USB to work when we load the kernel
directly.
No dma sync is performed after these operations as the data we read/write
is not used by the cpu after the calls to the maimbox driver.
Differential Revision: https://reviews.freebsd.org/D1940
Reviewed by: imp, Michal Meloun (meloun AT miracle.cz)
MFC after: 1 Week
Sponsored by: ABT Systems Ltd
* Even though I got the registers around "right", it seems
I'm not tickling the MDIO access correctly for the internal PHY
bus. Some of the switches are fine poking at the external PHY
registers; others aren't. So, enable direct PHY bus access
for the AR8327, and leave the existing code in place for the
others.
* Go and shuffle the register access around. Whilst here,
restore the 2ms delay if changing page.
* Comment out some of the stub printf()s; there's some upcoming
work to add port VLAN support.
Tested:
* AP135 development board
* Carambola2 - AR9331 SoC
When a gpiobus child is added, use its name to identify the mapped pin
names.
Make the respective changes to libgpio.
Add a new '-n' flag to gpioctl(8) to set the pin name.
Differential Revision: https://reviews.freebsd.org/D2002
Reviewed by: rpaulo
Requested by: many
The vtophys() function is used to get the physical page address for
the virtually allocated frame buffers when a physically continuous
memory area is not available. This change also allows removing the
masking of the FB_FLAG_NOMMAP flag in the PS3 syscons driver.
The FB and VT drivers were tested using X.org/xf86-video-scfb and
syscons.
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
(class and device) FDT UART. Define second one, UART_FDT_CLASS, for UART
class only.
This paves the way for declaring uart_class data and ofw/fdt compat data
with a uart implementation, rather than needing a big global table of
compat data and weak-symbol declarations of every existing implementation.
Differential Revision: https://reviews.freebsd.org/D1992
Submitted by: Michal Meloun
netmap rx queues, and the "batchiness" of rx updates sent to the chip.
These knobs will probably become per-rxq in the near future and will be
documented only after their final form is decided.
MFC after: 1 month
rework the code a little bit to use this function consistently to cleanup
all the changes made as part of the probe phase.
This fixes an issue where a FDT child node without a matching driver could
leave the GPIO pins mapped and prevent the further use of them.
This prints a warning when your system have a hinted child or a FDT child
node for which you don't have a matching driver:
gpiobus0: <unknown device> at pin(s) 24 irq 24
is the case, depending on the options, in some of the ARM hardware
simulators. In these cases we don't get an interrupt so will need to
schedule the task to write more data to the uart.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
This new function can be used by other drivers to reserve the use of GPIO
pins.
Anyway, the use of ofw_gpiobus_parse_gpios() is preferred when possible.
Requested by: Michal Meloun
the CPU nexus.
* Add ahb as a possible bus attachment
* Lay a comment down to remind me or whoever else ends up trying
to debug why the EEPROM isn't mapped in as to what's going on.
I noticed that openwrt/linux does this, citing "instability", so
until they figure out why I'm going to disable it here as well.
Tested:
* QCA AP135 - QCA955x SoC + AR8327 switch.
So, it turns out that the AR8327 has 7 ports internally:
* GMAC0 / external (CPU) MAC0
* GMAC1 / port1 -> GMAC5 / port5: external switch port PHYs
* GMAC6 / external (CPU) MAC1
Now, depending upon how things are wired up, the second CPU port (MAC1)
can be wired to either the switch (port6), or through port5's PHY, bypassing
the GMAC+switch entirely. Ie, it can pretend to be a boring PHY, saving
system designers from having to include a separate PHY for a "WAN" port.
Here's the rub - the AP135 board (QCA955x SoC) hooks up arge0 to
the second CPU port on the AR8327, but it's hooked up as RGMII.
So, in order to hook it up to the rest of the switch, it isn't configured
as a separate PHY - OpenWRT has it setup as connected via RGMII to
GMAC6 and (I'm guessing) it's set to be a WAN port by configuring up
port-based VLANs or something.
Thus, with a port mask of 0x3f, GMAC6 was never allowed to receive traffic
from any other port. It could transmit fine, but not receive anything.
So, now it works enough for me to continue doing board bootstrapping.
Note, this isn't enough to make the QCA955x + AR8327 work - there's
a bunch of uncommitted work to both the platform SoC (interrupt handling,
ethernet, etc) and the ethernet switch (register access space, setup, etc)
that needs to happen. However, this particular change is also relevant to
other SoCs, like the AR934x and AR7161, both of which can be glued to
this switch.
Tested:
* AP135 development board
TODO:
* Figure out whether I can somehow abuse another port mode to have this
be a pass-through PHY, or whether I should just create some more boot
time hints to explicitly set up port-based isolation so this works
in a more useful way by default.
The main purpose of this feature is to be able to unload a KMS driver.
When going back from the current vt(4) backend to the previous backend,
the previous backend is reinitialized with the special VDF_DOWNGRADE
flag set. Then the current driver is terminated with the new "vd_fini"
callback.
In the case of vt_fb and vt_vga, this allows the former to pass the
vgapci device vt_fb used to vt_vga so the device can be rePOSTed.
Differential Revision: https://reviews.freebsd.org/D687
Pass all SR-IOV configuration to the kernel using an nvlist. The
main benefit that this offers is flexibility. It allows a driver
to accept any number of parameters of any type supported by the
SR-IOV configuration infrastructure with having to make any
changes outside of the driver.
It also offers the user very fine-grained control over the
configuration of the VFs -- if they want, they can have different
configuration applied to every VF.
Differential Revision: https://reviews.freebsd.org/D82
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Add a function that validates that the user-provided SR-IOV
configuration is valid. This includes basic checks that the
structure of the configuration is correct (e.g. all required
configuration nodes are present) as well as validating against
a configuration schema.
The schema validation consists of:
- Ensuring that all required config parameters are present.
- If the schema defines a default value for a parameter,
adding the default value if the parameter is not set.
- Ensuring that no parameters are specified in the config
that are not defined in the schema.
- Ensuring that have the correct type defined in the schema.
- Ensuring that no configuration nodes are present for devices
that do not exist. For example, if 2 VFs are configured,
then we validate that a node called VF-5 does not exist.
Differential Revision: https://reviews.freebsd.org/D81
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
When creating VFs, we must size each SR-IOV BAR on the PF and
allocate a configuous I/O memory window large enough for every VF.
However, the window only needs to be aligned to a boundary equal
to the size of the window for a single VF.
When a VF attempts to allocate an I/O memory resource, we must
intercept the request in the pci driver and pass it off to the
SR-IOV code, which will allocate the correct window from the
pre-allocated memory space for the PF.
Inform the pci driver about the size and address of the BARs on
the VF when the VF is created. This is required by pciconf -b and
bhyve.
Differential Revision: https://reviews.freebsd.org/D78
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
The SR-IOV standard requires VFs to read all-ones when the VID
and DID registers are read. The VMM (hypervisor) is required to
emulate them instead. Make pci_read_config() do this emulation.
Change pci_user.c to use pci_read_config() to read config space
registers instead of going directly to the pcib so that the
emulated VID/DID registers work correctly on VFs. This is
required both for pciconf and bhyve PCI passthrough.
Differential Revision: https://reviews.freebsd.org/D77
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Implement the interace to create SR-IOV Virtual Functions (VFs).
When a driver registers that they support SR-IOV by calling
pci_setup_iov(), the SR-IOV code creates a new node in /dev/iov
for that device. An ioctl can be invoked on that device to
create VFs and have the driver initialize them.
At this point, allocating memory I/O windows (BARs) is not
supported.
Differential Revision: https://reviews.freebsd.org/D76
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Refactor PCI resource allocation code to allow a request for a
memory-mapped I/O window that is a multiple of a requested size.
This is needed by the SR-IOV code because the VF BARs are all
allocated contiguously. We can't just allocate a resource that is
a multiple of a single VF BAR because the size of an allocation
implies its alignment requirement.
Differential Revision: https://reviews.freebsd.org/D71
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
Refactor creation of PCI devices into helper methods that can be
used by the VF creation code.
Differential Revision: https://reviews.freebsd.org/D67
Reviewed by: jhb
MFC after: 1 month
Sponsored by: Sandvine Inc.
watchdog.c does an #ifdef DDB but does not #include "opt_ddb.h".
Fixing this turned up a missing include file.
MFC after: 1 week
X-MFC-With: r261495, r279410
property for devices that doesn't descend directly from gpiobus.
The parser supports multiple pins, different GPIO controllers and can use
arbitrary names for the property (to match the many linux variants:
cd-gpios, power-gpios, wp-gpios, etc.).
Pass the driver name on ofw_gpiobus_add_fdt_child(). Update gpioled to
match.
An usage example of ofw_gpiobus_parse_gpios() will follow soon.
I2C real-time clock (RTC).
The DS3231 has an integrated temperature-compensated crystal oscillator
(TXCO) and crystal.
DS3231 has a temperature sensor, an independent 32kHz output (which can be
turned on and off by the driver) and another output that can be used as
interrupt for alarms or as a second square-wave output, which frequency and
operation mode can be set by driver sysctl(8) knobs.
Differential Revision: https://reviews.freebsd.org/D1016
Reviewed by: ian, rpaulo
Tested on: Raspberry pi model B
The current GSO implementation in netback is broken and causes errors on the
guest tx path. While this is fixed disable GSO in order to have a working
netback.
Sponsored by: Citrix Systems R&D
Discussed with: gibbs
The optimization made in r239940 is valid for struct mbuf's current structure
and size in FreeBSD, but hardcodes assumptions about sizes of struct mbuf,
which are unfortunately broken if additional data is added to the beginning of
struct mbuf
X-MFC note (discussed with rwatson):
This change requires the MPKTHSIZE definition, which is only available after
head@r277203 and will not be MFCed as it breaks mbuf(9) KPI.
A direct commit to stable/10 and merges to other branches to add the necessary
definitions to work with the code as-is will be done to facilitate this MFC
PR: 194314
MFC after: 2 weeks
Approved/Reviewed by: erj, jfv
Sponsored by: EMC / Isilon Storage Division
Provide sys/dev/fdt/simplebus.h with the class declaration so that it
is possible to subclass FDT simplebus.
Differential Revision: https://reviews.freebsd.org/D1886
Reviewed by: nwhitehorn, imp
Summary:
For new eMMC chips, we must signal controller HC capability in OP_COND command.
Reviewers: imp, ian
Reviewed By: ian
Differential Revision: https://reviews.freebsd.org/D1920
With the patch applied the number of instruction events is 1% less and
number of mispredicted branch events is 5% less under multistream TCP
traffic load close to line rate.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
CDAI_FLAG_NONE advanced information CCB flag.
Support for the flag was merged to stable/10 in r279329, and the
__FreeBSD_version in stable/10 was bumped to 1001510.
Check for that version in the mps(4) and mpr(4) drivers when determining
whether to use the flag.
Sponsored by: Spectra Logic
MFC after: 3 days
dates.
- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).
- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.
- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.
- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)
- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().
- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.
- Fixed some formatting and whitespace.
- Bump version of mps driver to 20.00.00.00-fbsd
PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 2 weeks
It is disabled by default but users can set IFCAP_TXCSUM on the
netmap ifnet (ifconfig ncxl0 txcsum) to override netmap and force
the hardware to calculate and insert proper IP and L4 checksums in
outbound frames.
MFC after: 2 weeks
when re-enumerating a FULL speed device. Else the wrong max packet
setting might be used when trying to re-enumerate a FULL speed device.
MFC after: 3 days
Preliminary tests indicate 32 Mpps on tx, 24 Mpps on rx
with source and receiver on two different ports of the same 40G card.
Optimizations are likely possible.
The code follows closely the one for ixgbe so i do not
expect stability issues.
Hardware kindly supplied by Intel.
Reviewed by: Jack Vogel
MFC after: 1 week
To delay packets from a particular TX queue by a particular time, write a value
into the TX Pace table s.t. pace time <= TX Pace Clock Period * (2 ^ pace value)
- the TX pace clock is 1/13 of the system clock, so its period should be 104 or
52 ns depending on whether turbo mode is active.
EFX_TX_PACE_CLOCK_BASE added by me.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It solves locking problem when EFSYS_MEM_ALLOC is called in
the context holding a mutex (not allowed to sleep).
E.g. on interface bring up or multicast addresses addition.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It is one more place missed in the previous fix.
Most likely is was just memory leak on the error handling path since
typically efsys_mem_t is filled in by zeros on allocation.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Host-bus byte order translation is not requred.
Submitted by: Artem V. Andreev <Artem.Andreev at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use remaining number of DMA segment instead of maximum number in mapping
when checking space for one more TSO segment packet.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Sync endif comment with conditional.
BOOTROM and SIENA_BOOTROM are the same, but highlight that it is Siena.
Restore commented out assertion.
Sync comments with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Before the common code had hard coded limits on the IDs RXQs and TXQs could
be created with which were suited for the Windows driver with VMQ, and so
would prevent queues with IDs greater than or equal to 259 (for TXQs) or 768
(for RXQs) from being created. This change allows the limits to be set in
efsys.h, so that all 1024 queues can be created during new manftest tests.
Also, the descriptor cache sizes were also hard coded to values suited to
the smaller queue counts, and so it was necessary to make them configurable
as well.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Caught when efx_filter_init() failed and called efx_filter_fini() in the
teardown path.
Submitted by: Andrew Lee <alee at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Previously the driver's view was the expected outcome of any
reconfiguration even if that reconfiguration failed.
Submitted by: Ben Horgan
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
We must not enable RX queues with random parameters when they are
mapped into a VF with an untrusted driver. It's probably not a good
idea to do this anyway, so take this bit out of the table test masks.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Otherwise when processing finally comes to efx_tx_qdesc_post() it could
be insufficient space between reaped and added to post pending
descriptors.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
efx_ev_mcdi() does not assert or check that all event handlers it
calls are non-null. Add assertions at the top for all required
event handlers, as some events (in the case of this bug, monitor
events) are rare.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use nitem() to get number of array elements.
Remove unused define.
Use TAB to indent.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
TCP header is fragmented in the case of VLAN tagged IPv6 traffic without
HW VLAN tagging.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
will be used with arm64 to find which cpus to enable, and could also be
used with 32-bit arm and mips for the same purpose.
Differential Revision: https://reviews.freebsd.org/D1825
Sponsored by: The FreeBSD Foundation
This will be needed by arm64 to find the value to pass to the psci (Power
State Coordination Interface) driver, among other things, used to enable
cores.
Differential Revision: https://reviews.freebsd.org/D1824
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
properly.
If there is garbage in the flags field, it can sometimes include a
set CDAI_FLAG_STORE flag, which may cause either an error or
perhaps result in overwriting the field that was intended to be
read.
sys/cam/cam_ccb.h:
Add a new flag to the XPT_DEV_ADVINFO CCB, CDAI_FLAG_NONE,
that callers can use to set the flags field when no store
is desired.
sys/cam/scsi/scsi_enc_ses.c:
In ses_setphyspath_callback(), explicitly set the
XPT_DEV_ADVINFO flags to CDAI_FLAG_NONE when fetching the
physical path information. Instead of ORing in the
CDAI_FLAG_STORE flag when storing the physical path, set
the flags field to CDAI_FLAG_STORE.
sys/cam/scsi/scsi_sa.c:
Set the XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE when
fetching extended inquiry information.
sys/cam/scsi/scsi_da.c:
When storing extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_STORE instead of
ORing it into a field that isn't initialized.
sys/dev/mpr/mpr_sas.c,
sys/dev/mps/mps_sas.c:
When fetching extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE instead of
setting it to 0.
sbin/camcontrol/camcontrol.c:
When fetching a device ID, set the XPT_DEV_ADVINFO flags
field to CDAI_FLAG_NONE instead of 0.
sys/sys/param.h:
Bump __FreeBSD_version to 1100061 for the new XPT_DEV_ADVINFO
CCB flag, CDAI_FLAG_NONE.
Sponsored by: Spectra Logic
MFC after: 1 week
temporary buffer when remaining space is not enough to hold
a whole block.
- yarrow.c: add a comment that we intend to change the code and remove
memcpy's in the future. (*)
Requested by: markm (*)
Reviewed by: markm
Approved by: so (self)
Allocate the minimum or maximum response length for GET_BOARD_CFG as
appropriate. When looking up firmware subtypes by partition ID,
check the ID against the actual response length.
Merge of the patch made by Ben Hutchings in 2011.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Mainly to unify with similar member for transmit and receive queues.
It will be used in the future for resources allocation processing.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It avoids access to m_pkthdr when TSO packet is started and also makes
tso_start_new_packet() function smaller.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
sometimes. It will power up wrong and identify itself badly:
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cardbus0: <simple comms, UART> at device 0.1 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.2 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.3 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.4 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.5 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.6 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.7 (no driver attached)
All the higher numbered functions (.2 and above) have a config space
of all 0's. This smells a bit like a special debug mode, but the
current atheros driver doesn't cope. It is unclear if this card is
just a flake, or if we're doing something wrong in the power-up
sequence.
Put a work around into the code that tests for this rather unusual
condition. If we power a CardBus device up, and the device says it is
multi-function, and any of the functions have a 0 device ID, try the
power-up sequence again.
randomdev_init_reader to change read_random over to the newly installed
adaptor was missed. This means both read_random and arc4random (seeded
from read_random) were not returning very random data. This also
effects userland arc4random as it is seeded from kernel arc4random.
The random devices are uneffected and have returned good randomness
since the change.
All keys generated with a kernel of r273872 must be regenerated with
a kernel with this patch. Keys generated may be predictable.
Remove the warning as log is too early to print anything, and it would
always get printed due to early use of arc4random...
Reviewed by: delphij, markm
Approved by: so (delphij)
Highlights:
- Multiple verbs API updates
- Support for RoCE, RDMA over ethernet
All hardware drivers depending on the common infiniband stack has been
updated aswell.
Discussed with: np @
Sponsored by: Mellanox Technologies
MFC after: 1 month
interrupt status bit. According to the UHCI controller specification
the host controller halted interrupt is non-maskable.
PR: 156596
Tested by: adrian @
MFC after: 1 week
identifies the tested condition for _PRT as "BYTE value of 0", so the
remaining part of the conditionals is sufficient.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
This is to avoid a witness warning about a waiting memory allocation in
the evnt hanlder registration code.
Reported by: markj
MFC after: 3 days
X-MFC with: r277795
Xenstore user-space device has two problems currently:
- It does not correctly handle concurrent clients, because it's storing
each client data in dev->si_drv1.
- It does not correctly free this data when the client closes the device.
In order to solve both of this issues store the per-client data using
cdevpriv, which also comes with a hook in order to perform the necessary
cleanup on device close.
While there also make the device eternal.
Sponsored by: Citrix Systems R&D
Reported and Tested by: thompsa
MFC after: 2 weeks
Now compiler does not need any help.
The patch does not change generated code.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor), glebius
It makes sfxge_tso_state smaller and even makes tso_start_new_packet()
few bytes smaller. Data used to calculate packet size are used nearby,
so it should be no problems with cache etc.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor), glebius
has been removed and the driver has been greatly simplified and
optimised for FreeBSD. The driver is currently not built by default.
Requested by: Bruce Simpson <bms@fastmail.net>
This probably supports other devices based on SeaBIOS, which need
to be added to the smbios based quirks table.
The functionality has been ported from DragonFlyBSD and adapted
to FreeBSD's more general purpose environment.
Devices not covered by a quirk shouldn't be affected at all. Thanks
to jhb and kostikbel for reviewing the code.
Reviewed by: kostikbel, jhb
Approved by: jhb, kostikbel
Differential Revision: https://reviews.freebsd.org/D1802
1. handle errors from nm_config(), if any (none of the FreeBSD drivers
currently returns an error on this function, so this change
is a no-op at this time
2. use a full memory barrier on ioctls
interrupts are enabled and the NIC is awake (think: loading a module)
then there's a not-quite-zero window where we'll get an interrupt
for the device before the attach method is called to finish setting
up the hardware.
Since I grab locks in ath_intr() to check various things, the locks
need to be ready much earlier.
- Use IEEE80211_F_DATAPAD;
- (c->ic_flags & IEEE80211_CHAN_PASSIVE) -> IEEE80211_IS_CHAN_PASSIVE(c);
- Convert ackfailcnt to int (there is dereference to *(int *) in ieee80211_ratectl_tx_complete());
- Fix & move cleanup to the end in wpi_rx_done();
- Add missed lock in wpi_update_beacon();
- Try to fix powersave.
PR: kern/197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
especially on native monitor resolutions. This one essentially matches X11
default pointer.
Differential Revision: https://reviews.freebsd.org/D1801
No objection from: emaste
Approved by: adrian, dumbbell
o Ensure we use correct bank for MSK register
o Save and restore current bank in interrupt handler
o Stop TX watchdog on fatal errors
o Use right register for EPH status
This fixes operation on ARMv8 Foundation Model
Reviewed by: benno@
endpoint less frequently to make the sample rate adjustment more
accurate. This should resolve problems with the DN32-USB module for
Midas audio systems and possibly other similar products from Klark
Teknik.
MFC after: 3 days
Drivers (ULDs) and the base if_cxgbe driver.
Track the per-adapter activation of ULDs in a new "active_ulds" field.
This was done pretty arbitrarily before this change -- via TOM_INIT_DONE
in adapter->flags for TOM, and the (1 << MAX_NPORTS) bit in
adapter->offload_map for iWARP.
iWARP and hw-accelerated iSCSI rely on the TOE (supported by the TOM
ULD). The rules are:
a) If the iWARP and/or iSCSI ULDs are available when TOE is enabled then
iWARP and/or iSCSI are enabled too.
b) When the iWARP and iSCSI modules are loaded they go looking for
adapters with TOE enabled and enable themselves on that adapter.
c) You cannot deactivate or unload the TOM module from underneath iWARP
or iSCSI. Any such attempt will fail with EBUSY.
MFC after: 2 weeks
This is a sync against iwn(4) and openbsd.
- Add power management support;
- Add background scanning support;
- Fix few LORs;
- Handle rfkill switch state changes properly;
- Fix recovering after firmware failure;
- Add more error checking;
- Cleanup & disable by default debug output;
- Update macroses names;
- Other various fixes;
- Add IBSS support:
- don't set data_ntries field for management frames;
- Add AHDEMO support:
- fix padding;
- Sync eeprom functions;
- Use CMD_RXON_ASSOC where possible;
- Enable HW CCMP encryption/decryption for pairwise keys;
- Fix filter flags for CMD_RXON.
Tested (by submitter) - iwn 3945 NIC. I have one somewhere; I'll
validate this later on and revert it if it's a problem.
Thanks!
PR: 197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
particular, updates to the watchdog should no longer sleep.
- Add a new IPMI_IO_LOCK for low-level I/O access. Use this for
kcs_polled_request() and smic_polled_request().
- Add a new backend callback "ipmi_driver_request" to handle a driver
request. The new callback performs the request sychronously for KCS
and SMIC. SSIF still defers the work to the worker thread since the
worker thread sleeps during request processing anyway.
- Allocate driver requests on the stack rather than using malloc().
Differential Revision: https://reviews.freebsd.org/D1723
Tested by: scottl
MFC after: 2 weeks
allows the user to request administrative changes to individual devices
such as attach or detaching drivers or disabling and re-enabling devices.
- Add a new /dev/devctl2 character device which uses ioctls for device
requests. The ioctls use a common 'struct devreq' which is somewhat
similar to 'struct ifreq'.
- The ioctls identify the device to operate on via a string. This
string can either by the device's name, or it can be a bus-specific
address. (For unattached devices, a bus address is the only way to
locate a device.) Bus drivers register an eventhandler to claim
unrecognized device names that the driver recognizes as a valid address.
Two buses currently support addresses: ACPI recognizes any device
in the ACPI namespace via its full path starting with "\" and
the PCI bus driver recognizes an address specification of
'pci[<domain>:]<bus>:<slot>:<func>' (identical to the PCI selector
strings supported by pciconf).
- To make it easier to cut and paste, change the PnP location string
in the PCI bus driver to output a full PCI selector string rather
than 'slot=<slot> function=<func>'.
- Add a devctl(3) interface in libdevctl which provides a wrapper around
the ioctls and is the preferred interface for other userland code.
- Add a devctl(8) program which is a simple wrapper around the requests
supported by devctl(3).
- Add a device_is_suspended() function to check DF_SUSPENDED.
- Add a resource_unset_value() function that can be used to remove a
hint from the kernel environment. This is used to clear a
hint.<driver>.<unit>.disabled hint when re-enabling a boot-time
disabled device.
Reviewed by: imp (parts)
Requested by: imp (changing PCI location string)
Relnotes: yes
a dependency. This ensures "ifconfig cxl<n> ..." does the right thing
even when it's run with no driver loaded.
if_cxl.ko is the tiniest module in /boot/kernel.
MFC after: 2 weeks
Lock name should include interface name.
Tx queue and event queue lock name should include queue number.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Allow access to statistics data not only from sysctl handlers.
Submitted by: Boris Misenov <Boris.Misenov at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
