This is used for the on-board flash on the HiFive Unmatched board.
Reviewed by: #riscv, jrtc27
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D31562
This avoids exceeding a limit in the firmware when using ISO with
jumbo frames.
Reported by: Jithesh Arakkan @ Chelsio
Sponsored by: Chelsio Communications
These checks were inconsistently applied across the various hwpmc
classes. The condition is already checked by the generic code in
hwpmc_mod.c, so remove them.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D31388
It is always a good idea. In one case, attempting to allocate N+1 PMCs
from a class with N hardware counters would incorrectly attempt to
allocate from the next class in the list. Without this validation, this
can lead to all kinds of strange behaviour.
Since powerpc_allocate_pmc() is used by both the mpc7xxx and ppc970
classes, add a new global to track which is active (it will never be
both).
Reviewed by: luporl, ray
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D31387
This allows one to be able to map the sglist entries passed into the
vq_ring_enqueue_segments() function to the segment indexes used in
the virtqueue.
This function normally gets inlined and may not available via FBT
probes.
Differential Revision: https://reviews.freebsd.org/D31620
When adjusting resources we should write updated window base/limit into
the registers. Without this newly added address range won't be routed
through the bridge properly.
Use MIN()/MAX() against current window base/limit to not shrink it on
the other side if the window is shared by several resources.
Align passed resource start/end to the set window granularity to keep
it properly aligned. Currently this is mostly called by other bridges
having the same window alignment, but it may be change one day.
Reviewed by: jrtc27, jhb
MFC after: 1 week
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D31693
Cannon and Comet Lake PCHs have their PMC hidden, so when reading
the ACPI Base Address fails, we assume a default value.
Obtained from: Semihalf
Sponsored by: Stormshield
In implicit mode assignment of slot number and tracking id is performed
automatically on each synchronization requested by device driver.
This is done with creation of intermediate buffer for multitouch events.
This buffer holds untracked events until synchronization is requested by
device driver. It is needed as touch assigment requires
knowledges of all touch positions pushed in current and previous reports.
MFC after: 2 weeks
Touch tracking is a process of assignment of unique trackingID to each
initiated contact on the surface. Keeping the trackingIDs persistent
across multitouch reports requires solving of so called Euclidian
Bipartite Matching problem.
This commit imports EBM-solver implementation based on Dinitz-Kronrod
algorithm to find minimum cost matching between contacts listed in two
consecutive reports.
Obtained from: OpenBSD
MFC after: 2 weeks
with using of unioned anonymous structure.
Access to the same data by using different members of union generally
works despite it is not supported by C specs.
Also add helper function to report entire slot state.
MFC after: 2 weeks
As fuzz has already been applied on multitouch event processing.
This allows to remove existing workaround for double fuzz procesing.
MFC after: 2 weeks
1. Move touch count reporting helpers to utils. They are not multitouch.
2. Use evdev_mt prefix for private multitouch support routines.
3. Use int instead of int32_t where fixed size is not required.
4. Export some internal functions.
This change should be no-op.
MFC after: 2 weeks
As is done in the target, require that DataSN values are consecutive
and in-order. If an out of order Data-In PDU is received, force a
session reconnect. In addition, when a SCSI Response PDU is received,
verify that the ExpDataSN field matches the count of Data-In PDUs
received for this command. If not, force a session reconnect.
Reviewed by: mav
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D31594
This was an error, we cannot use sbuf_trim(9) in the
ixgbe_sbuf_fw_version function because it also gets called in
the context of sbuf_new_for_sysctl(9). sbuf(9) explains the interaction
with drain functions as used by sbuf_new_for_sysctl(9).
Reviewed by: imp
Fixes: 7660e4ea5c
MFC after: 1 day
Differential Revision: https://reviews.freebsd.org/D31633
Implement kernel support for RFC 5549/8950.
* Relax control plane restrictions and allow specifying IPv6 gateways
for IPv4 routes. This behavior is controlled by the
net.route.rib_route_ipv6_nexthop sysctl (on by default).
* Always pass final destination in ro->ro_dst in ip_forward().
* Use ro->ro_dst to exract packet family inside if_output() routines.
Consistently use RO_GET_FAMILY() macro to handle ro=NULL case.
* Pass extracted family to nd6_resolve() to get the LLE with proper encap.
It leverages recent lltable changes committed in c541bd368f.
Presence of the functionality can be checked using ipv4_rfc5549_support feature(3).
Example usage:
route add -net 192.0.0.0/24 -inet6 fe80::5054:ff:fe14:e319%vtnet0
Differential Revision: https://reviews.freebsd.org/D30398
MFC after: 2 weeks
- make sure rings are disabled during resets
- introduce netmap_update_hostrings_mode(), with support
for multiple host rings
- always initialize ni_bufs_head in netmap_if
ni_bufs_head was not properly initialized when no external buffers were
requestedx and contained the ni_bufs_head from the last request. This
was causing spurious buffer frees when alternating between apps that
used external buffers and apps that did not use them.
- check na validitity under lock on detach
- netmap_mem: fix leak on error path
- nm_dispatch: fix compilation on Raspberry Pi
MFC after: 2 weeks
When link_active_on_if_down flag is disabled and link is brought down
with ifconfig, FW reports a false positive link event about an
unqualified transceiver. The condition used in the driver to filter out
those false positive events was incorrect and caused that unqualified
module event to also not be reported when the event was valid.
Change the condition to rely on IFF_UP flag instead of
link_active_on_if_down and bump driver version to 2.3.1-k.
Signed-off-by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Signed-off-by: Eric Joyner <erj@FreeBSD.org>
Reviewed by: stallamr@netapp.com, erj@
Tested by: gowtham.kumar.ks@intel.com
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D30733
Before this change devq was frozen only if some command was sent to
the target after reset started, but release was called always. This
change freezes the devq immediately, leaving mprsas_action_scsiio()
check only to cover race condition due to different lock devq use.
This should also avoid unnecessary requeue of the commands, creating
additional log noise and confusing some broken apps.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
folder, only keeping the zero length packet API introduced in sys/dev/usb
after more reports of USB serial devices not supporting ZLPs.
Reported by: mav@
MFC after: 1 week
Sponsored by: NVIDIA Networking
SAS9305-16e with firmware 16.00.01.00 report HighPriorityCredit of
only 8, while for comparison some other combinations I have report
100 or even 128. In case of large JBOD detach requirement to send
target reset command to each target same time overflows the limit,
and without adequate handling makes devices stuck in half-detached
state, preventing later re-attach.
To handle that in case of allocation error mark the target with new
MPRSAS_TARGET_TOREMOVE flag, and retry the removal attempt next time
something else free high priority command. With this patch I can
successfully detach/attach 102 disk JBOD from/to the SAS9305-16e.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
MANA is the new network adapter from Microsoft which will be available
in Azure public cloud. It provides SRIOV NIC as virtual function to
guest OS running on Hyper-V.
The code can be divided into two major parts. Gdma_main.c is the one to
bring up the hardware board and drives all underlying hardware queue
infrastructure. Mana_en.c contains all main ethernet driver code.
It has only tested and supported on amd64 architecture.
PR: 256336
Reviewed by: decui@microsoft.com
Tested by: whu
MFC after: 2 week
Relnotes: yes
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D31150
Sync the e1000 shared code with DPDK shared code
"cid-gigabit.2020.06.05.tar.gz released by ND"
Primary focus was on client platforms (ich8lan). More work remains here
but we need an Intel contact for client networking.
Reviewed by: grehan, Intel Networking (erj, earlier rev)
Obtained from: DPDK <http://git.dpdk.org/dpdk/tree/drivers/net/e1000/base>
MFC after: 1 week
Sponsored by: me
Differential Revision: https://reviews.freebsd.org/D31547
Both zero-filling and/or deallocation can be done with vn_deallocate(9).
Sponsored by: The FreeBSD Foundation
Reviewed by: markj
Differential Revision: https://reviews.freebsd.org/D28899
When using iSCSI PDU offload (cxgbei) on T6 adapters, a burst of
received PDUs can be reported via a single message to the driver.
Previously the driver passed these multi-PDU bursts up to the iSCSI
stack up as a single "large" PDU by rewriting the buffer offset, data
segment length, and DataSN fields in the iSCSI header. The DataSN
field in particular was rewritten so that each of the "large" PDUs
used consecutively increasing values. While this worked, the forged
DataSN values did not match the ExpDataSN value in the subsequent SCSI
Response PDU. The initiator does not currently verify this value, but
the forged DataSN values prevent adding a check.
To avoid this, allow a logical iSCSI PDU (struct icl_pdu) to describe
a burst of PDUs via a new 'ip_additional_pdus' field. Normally this
field is set to zero when 'struct icl_pdu' represents a single PDU.
If logical PDU represents a burst of on-the-wire PDUs, then 'ip_npdus'
contains the count of additional on-the-wire PDUs. The header of this
"large" PDU is still modified, but the DataSN field now contains the
DataSN value of the first on-the-wire PDU in the burst.
Reviewed by: mav
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D31577
Remove redundant ofw property parsing in driver code, is already
taken care of in mmc_fdt_helpers.
Move ofw parsing to attach method.
Reviewed by: manu
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D31409
