peter and jhb: use __volatile__ to prevent gcc from possibly reordering
code, use a null inline instruction instead of a no-op movl (I would
have done this myself if I knew it was allowed) and combine two register
assignments into a single asm statement.
- if_ndis.c: set the NDIS_STATUS_PENDING flag on all outgoing packets
in ndis_start(), make the resource allocation code a little smarter
about how it selects the altmem range, correct a lock order reversal
in ndis_tick().
ndis_var.h
- In kern_ndis.c:ndis_send_packets(), avoid dereferencing NULL pointers
created when the driver's send routine immediately calls the txeof
handler (which releases the packets for us anyway).
- In if_ndis.c:ndis_80211_setstate(), implement WEP support.
- Clear out an_dma_vaddr on free so we can test to see if dma is
setup when the card is kldunloaded/kldloaded etc. only for MPI350
- Use a common detach like wi(4)
- Notify on RID read overflow and truncate this currently causes
a panic in -stable when the stack during an ifconfig an0 is done
with newer firmware
- Convert from UNLOCK/tsleep/LOCK to msleep. I thought I did that
a while ago.
method with something a little more intelligent: use BUS_GET_RESOURCE_LIST()
to run through all resources allocated to us and map them as needed. This
way we know exactly what resources need to be mapped and what their RIDs
are without having to guess. This simplifies both ndis_attach() and
ndis_convert_res(), and eliminates the unfriendly "ndisX: couldn't map
<foo>" messages that are sometimes emitted during driver load.
o move tx taps from ath_start to ath_tx_start so lots more
state is available to tap
o add tx flags
o add tx rate
o add tx power (constant for the moment)
o add tx antenna state
a new bpf_mtap2 routine that does the right thing for an mbuf
and a variable-length chunk of data that should be prepended.
o while we're sweeping the drivers, use u_int32_t uniformly when
when prepending the address family (several places were assuming
sizeof(int) was 4)
o return M_ASSERTVALID to BPF_MTAP* now that all stack-allocated
mbufs have been eliminated; this may better be moved to the bpf
routines
Reviewed by: arch@ and several others
For received packets, an status of NDIS_STATUS_RESOURCES means we need
to copy the packet data and return the ndis_packet to the driver immediatel.
NDIS_STATUS_SUCCESS means we get to hold onto the packet, but we have
to set the status to NDIS_STATUS_PENDING so the driver knows we're
going to hang onto it for a while.
For transmit packets, NDIS_STATUS_PENDING means the driver will
asynchronously return the packet to us via the ndis_txeof() routine,
and NDIS_STATUS_SUCCESS means the driver sent the frame, and NDIS
(i.e. the OS) retains ownership of the packet and can free it
right away.
evaluate them. Whatever they're meant to do, they're doing it wrong.
Also:
- Clean up last bits of NULL fallout in subr_pe
- Don't let ndis_ifmedia_sts() do anything if the IFF_UP flag isn't set
- Implement NdisSystemProcessorCount() and NdisQueryMapRegisterCount().
flag isn't set.
- In ndis_attach(), halt the NIC before exiting the routine. Calling
ndis_init() will bring it up again, and we don't want it running
(and potentially generating interrupts) until we're ready to deal
with it.
mbuf<->packet housekeeping. Instead, add a couple of extra fields
to the end of ndis_packet. These should be invisible to the Windows
driver module.
This also lets me get rid of a little bit of evil from ndis_ptom()
(frobbing of the ext_buf field instead of relying on the MEXTADD()
macro).
- Fix ndis_time().
- Implement NdisGetSystemUpTime().
- Implement RtlCopyUnicodeString() and RtlUnicodeStringToAnsiString().
- In ndis_getstate_80211(), use sc->ndis_link to determine connect
status.
Submitted by: Brian Feldman <green@freebsd.org>
- Add explicit cardbus attachment in if_ndis.c
- Clean up after moving bus_setup_intr() in ndis_attach().
- When setting an ssid, program an empty ssid as a 1-byte string
with a single 0 byte. The Microsoft documentation says this is
how you're supposed to tell the NIC to attach to 'any' ssid.
- Keep trace of callout handles for timers externally from the
ndis_miniport_timer structs, and run through and clobber them
all after invoking the haltfunc just in case the driver left one
running. (We need to make sure all timers are cancelled on driver
unload.)
- Handle the 'cancelled' argument in ndis_cancel_timer() correctly.
supposed to be opaque to the driver, however it is exposed through
several macros which expect certain behavior. In my original
implementation, I used the mappedsystemva member of the structure
to hold a pointer to the buffer and bytecount to hold the length.
It turns out you must use the startva pointer to point to the
page containing the start of the buffer and set byteoffset to
the offset within the page where the buffer starts. So, for a buffer
with address 'baseva,' startva is baseva & ~(PAGE_SIZE -1) and
byteoffset is baseva & (PAGE_SIZE -1). We have to maintain this
convention everywhere that ndis_buffers are used.
Fortunately, Microsoft defines some macros for initializing and
manipulating NDIS_BUFFER structures in ntddk.h. I adapted some
of them for use here and used them where appropriate.
This fixes the discrepancy I observed between how RX'ed packet sizes
were being reported in the Broadcom wireless driver and the sample
ethernet drivers that I've tested. This should also help the
Intel Centrino wireless driver work.
Also try to properly initialize the 802.11 BSS and IBSS channels.
(Sadly, the channel value is meaningless since there's no way
in the existing NDIS API to get/set the channel, but this should
take care of any 'invalid channel (NULL)' messages printed on
the console.
broken BIOS. Separate ohci_controller_init() from ohci_init(),
and call ohci_controller_init() at resume process once more.
Discussed on [bsd-nomads:16737] - [bsd-nomads:16746].
Submitted by Hiroyuki Aizu <eyes@navi.org> [bsd-nomads:16741]
methods for USB devices in the same way of uhci driver. But this change
is not complete because some ohci controlers are not initialized completely.
So "kernel: usb0: 1 scheduling overruns" interrupt will generate many times.
This change will be same one in PR kern/60099.
Discussed on [bsd-nomads:16737] - [bsd-nomads:16746].
- Make ndis_get_info()/ndis_set_info() sleep on the setdone/getdone
routines if they get back NDIS_STATUS_PENDING.
- Add a bunch of net80211 support so that 802.11 cards can be twiddled
with ifconfig. This still needs more work and is not guaranteed to
work for everyone. It works on my 802.11b/g card anyway.
The problem here is Microsoft doesn't provide a good way to a) learn
all the rates that a card supports (if it has more than 8, you're
kinda hosed) and b) doesn't provide a good way to distinguish between
802.11b, 802.11b/g an 802.11a/b/g cards, so you sort of have to guess.
Setting the SSID and switching between infrastructure/adhoc modes
should work. WEP still needs to be implemented. I can't find any API
for getting/setting the channel other than the registry/sysctl keys.
to each other.
Correct the recovery thread's loop so that it
will terminate properly on shutdown. We also
clear the recovery_thread proc pointer so that
any additional calls to aic_terminate_recovery_thread()
will not attempt to kill a thread that doesn't
exist. Lastly, code the loop so that termination
will still be successfull even if the termination
request occurs just prior to us entering the loop
or while the recovery thread is off recovering
commands.
that would cause an infinite loop any time we
manually flush the good status FIFO. Also make
our loop delay unconditional to ensure we don't
miss any FIFO allocations by the hardware.
definitions for more than one device (usually differentiated by
the PCI subvendor/subdevice ID). Each device also has its own tree
of registry keys. In some cases, each device has the same keys, but
sometimes each device has a unique tree but with overlap. Originally,
I just had ndiscvt(8) dump out all the keys it could find, and we
would try to apply them to every device we could find. Now, each key
has an index number that matches it to a device in the device ID list.
This lets us create just the keys that apply to a particular device.
I also added an extra field to the device list to hold the subvendor
and subdevice ID.
Some devices are generic, i.e. there is no subsystem definition. If
we have a device that doesn't match a specific subsystem value and
we have a generic entry, we use the generic entry.
Implement this in acpi_MatchHid() and acpi_isa_get_compatid(). This
should fix mouse support for some users.
Move all users of AcpiGetObjectInfo() to use dynamic storage instead of
a devinfo on the stack. This is necessary since ACPI-CA needs to
allocate different sized arrays for the CompatList.
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
the psim simulator. Look for the "file" property which only exists
on psim disks, and as a bonus, print the contents of this at boot-time,
which is the host file being used for the disk image.
- remove remaining warnings.
transfer size to the stripe size. This is a different
situation from reviving, where this limitation is necessary.
In initsd we're simply writing binary zeroes to the entire
disk, so the only effect of limiting the transfer is to slow
things down.
ndis_send_packets() but there's no link yet, we get an immediate
callback to ndis_txeof(), which clears if_timer. But ndis_start()
sets if_timer right after the call to ndis_send_packets(). Set
if_timer before calling ndis_send_packets().
Also fix mutex locking to prevent ndis_txeof() from running in
the middle of ndis_start().
make it more robust. This should fix problems with crashes under
heavy traffic loads that have been reported. Also add a 'query done'
callback handler to satisfy the e100bex.sys sample Intel driver.
throttling values being available regardless of the CPU's capabilities.
This has been broken since rev 1.1. Also clarify a comment.
Submitted by: Taku YAMAMATO <taku@cent.saitama-u.ac.jp>
Write 100 times for tomorrow:
I will never again free(9) a modified pointer.
Pointy Hat: yeah, yeah, yeah, can you just put it in the pile over there...
Yes, it's what you think it is. Yes, you should run away now.
This is a special compatibility module for allowing Windows NDIS
miniport network drivers to be used with FreeBSD/x86. This provides
_binary_ NDIS compatibility (not source): you can run NDIS driver
code, but you can't build it. There are three main parts:
sys/compat/ndis: the NDIS compat API, which provides binary
compatibility functions for many routines in NDIS.SYS, HAL.dll
and ntoskrnl.exe in Windows (these are the three modules that
most NDIS miniport drivers use). The compat module also contains
a small PE relocator/dynalinker which relocates the Windows .SYS
image and then patches in our native routines.
sys/dev/if_ndis: the if_ndis driver wrapper. This module makes
use of the ndis compat API and can be compiled with a specially
prepared binary image file (ndis_driver_data.h) containing the
Windows .SYS image and registry key information parsed out of the
accompanying .INF file. Once if_ndis.ko is built, it can be loaded
and unloaded just like a native FreeBSD kenrel module.
usr.sbin/ndiscvt: a special utility that converts foo.sys and foo.inf
into an ndis_driver_data.h file that can be compiled into if_ndis.o.
Contains an .inf file parser graciously provided by Matt Dodd (and
mercilessly hacked upon by me) that strips out device ID info and
registry key info from a .INF file and packages it up with a binary
image array. The ndiscvt(8) utility also does some manipulation of
the segments within the .sys file to make life easier for the kernel
loader. (Doing the manipulation here saves the kernel code from having
to move things around later, which would waste memory.)
ndiscvt is only built for the i386 arch. Only files.i386 has been
updated, and none of this is turned on in GENERIC. It should probably
work on pc98. I have no idea about amd64 or ia64 at this point.
This is still a work in progress. I estimate it's about %85 done, but
I want it under CVS control so I can track subsequent changes. It has
been tested with exactly three drivers: the LinkSys LNE100TX v4 driver
(Lne100v4.sys), the sample Intel 82559 driver from the Windows DDK
(e100bex.sys) and the Broadcom BCM43xx wireless driver (bcmwl5.sys). It
still needs to have a net80211 stuff added to it. To use it, you would
do something like this:
# cd /sys/modules/ndis
# make; make load
# cd /sys/modules/if_ndis
# ndiscvt -i /path/to/foo.inf -s /path/to/foo.sys -o ndis_driver_data.h
# make; make load
# sysctl -a | grep ndis
All registry keys are mapped to sysctl nodes. Sometimes drivers refer
to registry keys that aren't mentioned in foo.inf. If this happens,
the NDIS API module creates sysctl nodes for these keys on the fly so
you can tweak them.
An example usage of the Broadcom wireless driver would be:
# sysctl hw.ndis0.EnableAutoConnect=1
# sysctl hw.ndis0.SSID="MY_SSID"
# sysctl hw.ndis0.NetworkType=0 (0 for bss, 1 for adhoc)
# ifconfig ndis0 <my ipaddr> netmask 0xffffff00 up
Things to be done:
- get rid of debug messages
- add in ndis80211 support
- defer transmissions until after a status update with
NDIS_STATUS_CONNECTED occurs
- Create smarter lookaside list support
- Split off if_ndis_pci.c and if_ndis_pccard.c attachments
- Make sure PCMCIA support works
- Fix ndiscvt to properly parse PCMCIA device IDs from INF files
- write ndisapi.9 man page
when using a KVM.
There is no actual solution possible, but this gets us pretty close.
Typically when switching back to a FreeBSD box and moving the mouse
wild data is produced, because the protocol's validation/checksum
system is extremely weak it is impossible to determine that we're
out of sync before dropping several bogus packets to user land.
The actual solution that appears to offer the best clamping of
jitter is to buffer the mouse packets if we've not seen mouse
activity for more than .5 seconds. Then waiting to flush that data
for 1/20th of a second. If within that 20th of a second we get any
packets that do fail the weak test we drop the entire queue and
back off accepting data from the mouse for 2 seconds and then repeat
the whole deal.
You can still get _some_ jitter, notably if you switch to the FreeBSD
box, then move the mouse just enough to generate one or two packets.
Those packets may be bogus, but may still pass the validity check.
One way to finally kill the problem once and for all is to check
the initial packets for "wild" values. Typically one sees packets
in the +/-60 range during normal operation, however when bogus data
is generated it's typically near the outer range of +/-120 or more,
those packets would be a good candidate for dropping or clamping.
I've been running with this for several weeks now and it has
significantly helped me stay sane even with a piece of junk Belkin
KVM causing wild jitter each and every time I switch.
Lastly I'd like to note that my experience with Windows shows me that
somehow the Microsoft PS/2 driver typically avoids this problem, but
that may only be possible when running the mouse in a dumb-ed down PS/2
mode that Belkin recommends on their site.
versions of the firmware. It responds more slowly to commands, and we
bogusly failed them. We assume that all versions of the intersil
firmware before 1.0 are 10 times slower and will give it 10x the time
to finish.
# for 5.2 we should always just assume 5s.
Serialize access to the SATA channels, the chip messes up if
both channels are used at the same time.
The SiI3112 hereby takes the price as the most crappy SATA chip in
existance by a significant amount.
My advise to our userbase is to avoid this chip like the plague...
Setup decent transfer mode defaults as some BIOS's seem to put in
things that it *knows* doesn't work.
(Note to BIOS writers: stop doing that nonsense, we will get things
working with your crappy HW anyways, and then recommend users to buy
someone else's products that "just works", thankyou.. )
Limit the device transfer mode to ATA100/UDMA5 on generic SATA.
Since we dont know if the user is using a pure SATA device or an
old PATA drive with a SATA converter dongle, we need to limit the
speed used here to cover up the problems with Marvell ATA-SATA bridges
used in lots of SATA products.
This workaround is enabled for all detectable SATA controllers as they
seem to have semilar problems here. One notable exception is all the
Promise pdc2037x chips which just always work (cudos to Promise!).
as these ioctl's aren't MD. This also means they are installed in
/usr/include/dev/bktr now. Also provide compatability wrappers for
where these headers lived in 4.x.
mutex to be locked. It is redundant since em_init() is called and this
correctly locks the mutex and calls em_stop().
5.2 release candidate since this can cause a panic if the watchdog
expires.
Tested by: kuriyama
lots of old interfaces, and digi now supports all cards that dgb
supported. The author of the driver says that this is no longer
necessary.
Approved by: babkin@
a long time: lmc The LAN Media Corp PCI WAN driver based on tulip.
This driver hasn't compiled for 3 years since the PCI compat shims
were removed, and Lan Media appears to have gone out of business.
These cards appear to be rare (a recent search of ebay had no hits).
Should someone wish to revive this driver, submitting patches to make
it compile plus a testing report will bring it back.
- Dynamically allocate the cpu_softc[] array based on mp_maxid instead of
using a statically sized array that depended on 'options SMP'.
- Use mp_maxid rather than MAXCPU when walking all the CPUs looking for a
match.
- Always call smp_rendezvous() since UP kernels now provide this.
- Use mp_ncpus rather than cpu_ndevices when determining if we need to
disable C3 for SMP machines.
Approved by: re (rwatson)
Reviewed by: njl
This is the vastly updated cx drvier from Roman Kurakin <rik@cronyx.ru>
who has been patiently waiting for this update for sometime.
The driver is mostly a rewrite from the version we have in the tree.
While some similarities remain, losing the little history that the old
driver has is not a big loss, and the re@ felt it was easier this way (less
error prone).
The userland parts of this update will be committed shortly.
The driver is not connected to the build yet. I want to make sure I
don't break any platform at any time, so I want to test that with
these files in the tree before I continue (on the off chance I'm
forgetting a file).
I changed the DEBUG macro to CX_DEBUG from the code that was submitted
(to not break when we go to building with opt_global.h after the
release), as well adding $FreeBSD$.
Submitted by: Roman Kurakin
Approved by: re@ <scottl>
code. Both the driver and the new code were wrong. Driver interrupt
handlers are supposed to take "void *vsc" arg, but some including all
COMPAT_ISA drivers and the pci part of the cy driver want an "int unit"
arg. They got this using bogus casts of function pointers which should
have kept working despite their bogusness. However, the new interrupt
code doesn't honor requests to pass an arg of ((void *)0), so things
are very broken if the arg is actually a representation of unit 0.
The fix is to use a normal "void *vsc" arg for the pci case and a
wrapper for the COMPAT_ISA case (of the cy driver). This cleans up
new-busification of the pci case but takes the COMPAT_ISA case a little
further from new-bus. The corresponding bug for the COMPAT_ISA case
has already been fixed similarly using a wrapper in compat_isa.c and
we need another wrapper just to undo that.
Fixed some directly related style bugs (mainly by removing compatibility
cruft).
cy.c:
Fixed an indirectly related old bug in cyattach_common(). A wrong status
was returned in the unlikely event that malloc() failed.
Approved by: re (scottl)
issues which they found and asked to be changed so 3ware can offcially
support the driver.
Summary of the most significant changes:
- TWE_OVERRIDE is no longer supported
- If twe_getparam failed, bogus data would be returned to the caller
- Cache the device unit in the twe_drive structure to aid debugging
- Add the 3ware driver version.
- Proper return error codes for many functions.
- Track the minimum queue length statistics
- 4.x compat: use the cached unit number from the twe_drive structure
instead of the the cached si_drv2. 3ware found that after many loads
and unloads that si_drv2 became corrupted. This did not happen in
-current.
Submitted by: Vinod Kashyap (with modifications by me)
Approved by: re (rwatson)
o Back out workaround for not resetting lucent cards more than once. With
these fixes, it appaers they are no longer necessary.
o Set wi_gone when the card goes awol: typically when we get 0xffff back from
the card. Also, don't interact with a card that's gone, so we fail in
seconds rather than minutes. Also reduce amount of time we wait to .5s
in wi_cmd.
o clear wi_gone on ifconfig down to give some cards a chance after they wedge
(this appears to unwedge one of my prism cards with old firmware). ifconfig
up will fail quickly enough if the card really is out to lunch.
o Add delay in wi_init of 100ms.
o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we
exit out of the interrupt routine by just acking the interrupt
Submitted by: iedowse
Approved by: re@ (scottl)
# after the freeze I'll fix some of the minor style issues that reviewers
# of this patch have told me about.
using critcal_enter() and critical_exit() to attempt to replace spl*()
calls. The critical section was calling selrecord(), which locks an
MTX_DEF mutex, which is not legal in a critical section.
Tested by: Stefan Ehmann <shoesoft@gmx.net> and "make universe"
Approved by: re (scottl)
The altio resource magic no longer worked probably due to other changes
in the kernel. Redo that part so it also fits better into ATAng.
Fix detach so it doesn't panic the system when a pccard device is
yanked.
Approved by: re@
o fix race condition when processing rx descriptors: because we use
a self-linked descriptor at the end of the rx descriptor list to
avoid rx overruns (which can easily happen for 5212 parts that enable
PHY errors) we must carefully check that a descriptor is "done" by
looking ahead to the next descriptor before believing the done bit
in the current descriptor (this is all handled in the HAL since the
rx descriptor format is chip-specific so we need to pass in two
additional parameters--the physical address of the current descriptor
and the virtual address of the next descriptor in the list)
o check copyout return status for SIOCGATHSTATS ioctl
Approved by: re (scottl)
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
them working (cache, automatic rebuild and hotswap) the FFDC
info (First Failure Data Capture) on the adapter must be
initialised.
Logical drives in critical/degraded states weren't added to
the drive list. FreeBSD was not able to see a degraded array
after a reboot. Degraded drives are now also added to the drivelist
and the state of the logical drive is given at boottime.
The adapter type is detected from informations in nvram page 5
and displayed at boottime.
Change IPS_OS_FREEBSD definition from 10 to 8 according to IBM
specs.
Submitted by: <Patrick Guelat> pgfb@imp.ch
Reviewed by: mbr, scottl
Approved by: re
idx'th present CPU with pc_acpi_id equal to *acpi_id. If *acpi_id
does not match that processor's pc_acpi_id, return the value for
ProcId derived from the MADT in *acpi_id. If pc_acpi_id is 0xffffffff,
always override it with the value of *acpi_id. Finally, return
pc_cpuid in *cpu_id and use that as our primary key.
* Use pc_cpuid as our unique key because we know it is valid since
MD code set it. The values for ProcId in the ASL and MADT don't
match up on some machines (!), forcing us to fall back to ordered
probing in that case.
* Remove some #ifdef SMP since the refcount doesn't hurt performance
and will be needed for dynamic _CST objects. Only one #ifdef SMP
(for smp_rendezvous) remains.
* Hook up SMP in the compile flags in the Makefile.
Tested by: marcel, truckman
Approved by: re (scottl)
transfer descriptors when a large request needs to be split into
more than one 8k chunk. The bug was that the calculation did not
take into account the offset of the chunk within the overall request.
This is reported to fix crashes and data corruption on ohci
controllers.
Submitted by: green
Approved by: re
boot-disabled devices instead of skipping the last interrupt. This is
especially important for devices that only have one interrupt as this
bug was keeping any interrupt from being tried at all.
Reviewed by: msmith
Approved by: re (scottl)
happen in interrupt context; 1) sleep locks, and 2) malloc/free
calls.
1) is fixed by using spin locks instead.
2) is fixed by preallocating a FIFO (implemented with a STAILQ)
and using elements from this FIFO instead. This turns out
to be rather fast.
OK'ed by: re (scottl)
Thanks to: peter, jhb, rwatson, jake
Apologies to: *
an acpi_cpu method for shutdown that disables entry to acpi_cpu_idle
and then IPIs/waits for threads to exit. This fixes a panic late in
reboot in the SMP case.
* In the !SMP case, don't use the processor id filled out by the MADT
since there can only be one processor. This was causing a panic in
acpi_cpu_idle if the id was 1 since the data was being dereferenced from
cpu_softc[1] even though the actual data was in cpu_softc[0] (which is
correct).
* Rework the initialization functions so that cpu_idle_hook is written
late in the boot process.
* Make the P_BLK, P_BLK_LEN, and cpu_cx_count all softc-local variables.
This will help SMP boxes that have _CST or multiple P_BLKs. No such
boxes are known at this time.
* Always allocate the C1 state, even if the P_BLK is invalid. This means
we will always take over idling if enabled. Remove the value -1 as
valid for cx_lowest since this is redundant with machdep.cpu_idle_hlt.
* Reduce locking for the throttle initialization case to around the write
to the smi_cmd port. Add disabled code to write the CST_CNT. It will
be enabled once _CST re-evaluation is tested (post 5.2R).
Thank you: dfr, imp, jhb, marcel, peter
Tested by: rwatson, Harald Schmalzbauer <h@schmalzbauer.de>
Approved by: re (rwatson)
the "old" SYSINIT. This makes sure things happen in the right order.
XXX: md(4) needs to be fully geom-ified and in particluar /dev/md.ctl
should be abandonded for the GEOM OaM api.
Approved by: re@
TOC's for the same media!! that borks up GEOM.
Although this looks like bad HW the following patch removes the
chance for GEOM panic'ing.
Approved by: re@
o Each source gets its own queue, which is a FIFO, not a ring buffer.
The FIFOs are implemented with the sys/queue.h macros. The separation
is so that a low entropy/high rate source can't swamp the harvester
with low-grade entropy and destroy the reseeds.
o Each FIFO is limited to 256 (set as a macro, so adjustable) events
queueable. Full FIFOs are ignored by the harvester. This is to
prevent memory wastage, and helps to keep the kernel thread CPU
usage within reasonable limits.
o There is no need to break up the event harvesting into ${burst}
sized chunks, so retire that feature.
o Break the device away from its roots with the memory device, and
allow it to get its major number automagically.
- This is heavily derived from John Baldwin's apic/pci cleanup on i386.
- I have completely rewritten or drastically cleaned up some other parts.
(in particular, bootstrap)
- This is still a WIP. It seems that there are some highly bogus bioses
on nVidia nForce3-150 boards. I can't stress how broken these boards
are. I have a workaround in mind, but right now the Asus SK8N is broken.
The Gigabyte K8NPro (nVidia based) is also mind-numbingly hosed.
- Most of my testing has been with SCHED_ULE. SCHED_4BSD works.
- the apic and acpi components are 'standard'.
- If you have an nVidia nForce3-150 board, you are stuck with 'device
atpic' in addition, because they somehow managed to forget to connect the
8254 timer to the apic, even though its in the same silicon! ARGH!
This directly violates the ACPI spec.
with multiple ports on a shared interrupt demultiplexed by the puc_intr()
handler.
siointr1() first read as much input as possible and then checked all
possibly-relevant status registers, partly for robustness and partly
for historical reasons. This is very bad if it is called for every
port sharing an interrupt like puc_intr() does. It can spend too long
reading all the input for some ports when the interrupt is for a more
urgent event on another, or just too long checking all the status
registers when there are lots of ports. The inter-character time is
too long for reading all the input even when the interrupt is for a
transmitter interrupt on the same port, and at 921600 bps the inter-char
time is 10.85 usec and was often exceeded with just 2 ports, leaving
the transmitters idle for about 6% of the time.
The tweak is to break out of the read loop after reading 1 char if
output can be done. This avoids most of the idle transmitter time for
2 active ports at 921600 bps bidirectional on the test system. It
also reduces overhead by about 20%. More complete fixes use the
programmable tx low watermark on 16950's and reduce overhead by another
65%.
will now need editing except for spot checks.
Changed this buffer from a circular one to a linear one. This is more
useful for some cases and the sysctl that prints it doesn't support
circular buffers.
Fixed (output) formatting bugs in this sysctl. An off by 1 error caused
a garbage byte to be returned after annotation of large deltas, and
a race with the writer sometimes caused premature string termination.
o when compiling lint, undefine certain things and redefine them so that the
driver doesn't #error out. Since lint kernels aren't supposed to be
bootable, I'm no troubled by this breakage.
This fixes the tinderbox
Suggested by: rwatson
Approved by: bms
Its restoration in rev.1.102 was mistranslated to the equivalent of
setsofttty() in rev.1.105. This increased overheads by causing a
context switch to the SWI handler after almost every interrupt. The
increase was approx. 50% on a Celeron 366 (from 23 usec to 34 usec
per interrupt).
* Use the cpu_idle_hook() to do idling for C1-C3.
* Use both _CST and the FADT to detect Cx states.
* Use both _PTC and P_CNT for controlling throttling.
* Add a notify handler to detect changes in _CST and _PSS
* Call the _INI function for each processor if present. This will be
done by ACPI-CA in the future.
* Fix a bug on SMP systems where CPUs will attach multiple times if the
bus is rescan.
* Document new sysctls for controlling idling.
- For acpi_pci_link_entry_dump(), add a few helper functions to display
the trigger mode, polarity, and sharemode of an individual IRQ resource.
These functions are then called for both regular and extended IRQ
resources.
- In acpi_pci_link_set_irq(), use the same type of IRQ resource
(regular vs. extended) for the new current resource as the type of
the resources from _PRS.
- When routing an interrupt don't ignore extended IRQ resources. Also,
use the same type of IRQ resource (regular vs. extended) for the new
current resource when as the type of the resource from _PRS.
Tested by: peter
the packets are immediately returned for sending (e.g. when bridging
or packet forwarding). There are more efficient ways to do this
but for now use the least intrusive approach.
Reviewed by: imp, rwatson
- In the receive routine handle the case where last descriptor could have
less than 4 bytes of data.
- Handle race between detach/ioctl routine.
MFC after: 3 days
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
5212-based devices because PHY errors are used to collect data
on environmental noise that and doesn't truly reflect the state
of the communications media. The result is confused users.
Folks that want to watch PHY errors can still get the statistics
through the device ioctl (used by athstats).
Radeon IGP support (still lacking PCI IDs), and DRM interface 1.2 updates which
include finally tying the DRM instances to specific devices rather than relying
on the X Server.
- Fail in agp_alloc_gatt if the aperture size is 0 instead of panicing in
contigmalloc.
Reported by: Bjoern Fischer <bfischer@Techfak.Uni-Bielefeld.DE>
Reviewed by: jhb
MFC after: 1 week
dsp_open: rearrange to only hold one lock at a time
dsp_close: ditto
mixer_hwvol_init: delete locking, the only consumer seems to
be the ess driver and it only call it a creation time, I
think the device will be stable across the sleepable malloc.
cmi interrupt routine: Release locks while caller chn_intr,
either this or do what emu10k1 does which is have no locks
at in the interrupt handler.
Submitted by: mat@cnd.mcgill.ca
crashes that had sn0 as the irq that's being serviced, when there was
no sn0 in the system. This seems to prevent them. Also, we want to
wait until after we've registered with the network layer before we
turn on the interrupt spigot to avoid races.
revision 1.142
date: 2003/10/11 03:04:26; author: toshii
Fix a done list handling bug which exhibits under high shared
interrupt rate and bus traffic. As the interrupt register is
read after checking hcca_done_head, there was a small chance
of dropping a done list. Ignore OHCI_WDH interrupt bit if
hcca_done_head is zero so that OHCI_WDH is processed later.
revision 1.141
date: 2003/09/10 20:08:29; author: mycroft;
Update actlen even in the case where a TD returns an error --
this is critical for the umass bulk-only STALL case.
revision 1.176
date: 2003/11/04 19:11:21; author: mycroft;
Ignore a CRCTO error on a SETUP transaction in combination with
STALLED or NAK. This fixes problems with the GL641.
- remove the unnecessary elm arg from SIMPLEQ_REMOVE_HEAD().
this mirrors the functionality of SLIST_REMOVE_HEAD() (the other
singly-linked list type) and FreeBSD's STAILQ_REMOVE_HEAD()
o When we're resetting the board, make sure that we error out the pending
CCBs first. Otherwise the aha_cmd won't accept further commands, such
as those that are used to reset the card (AOP_INITIALIZE_MBOX). This
appears to cause a cascade failure where no more commands are possible
to the card.
o Reduce from 10s down to 1s the amount of time we're willing to tolerate
the card being awol. This helps the above case.
o Add some error checking to two commands issued in the probe.
I have a dim memory of gibbs@ trying to tell me about this problem a
few years ago, so pointy hat to imp@ for sitting on it so long.
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
whether or not the isr needs to hold Giant when running; Giant-less
operation is also controlled by the setting of debug_mpsafenet
o mark all netisr's except NETISR_IP as needing Giant
o add a GIANT_REQUIRED assertion to the top of netisr's that need Giant
o pickup Giant (when debug_mpsafenet is 1) inside ip_input before
calling up with a packet
o change netisr handling so swi_net runs w/o Giant; instead we grab
Giant before invoking handlers based on whether the handler needs Giant
o change netisr handling so that netisr's that are marked MPSAFE may
have multiple instances active at a time
o add netisr statistics for packets dropped because the isr is inactive
Supported by: FreeBSD Foundation
PALM_4 initialisation hack. I've not confirmed it myself, but
seeing as we already don't use it for the Sony Clie_41, let's drop
it from the Clie_40 also and see what happens.
(Question: What about the Clie_S360 and Clie_NX60 devices? Do we
need to drop Palm4 from those as well? Possibly, but I've not had
any reports about those so I don't know.)
PR: kern/56575
MFC after: 3 days
but can be enabled by setting hw.atm.hatmN.mpsafe in the kernel
environment to a non-zero value before loading the driver. When
the problems with network MPSAFEty have been sorted out this will
be removed and the driver will default to MPSAFE.
We put them directly onto the free list instead of calling the
external mbuf free routine (that routine would have cleaned the flag).
This fixes a bug which manifests itself in falsely reporting a lot of used
buffers when configuring the interface down.
from the xe driver. Should probably be removed when current probe/attach
problems with the driver are fixed, but is useful now when requesting
diagnostic information from users.
Reviewed by: imp (mentor)
o Fix minor type problems
o Fix minor problem with a couple debug printfs.
o Default to a sane media type when none is reported.
o Minor style changes
The PR complains this will fix the IBM 300GL cards.
Submitted by: Max Gotlib
PR: 11462
operating mode to HostAP, the card will lock up indefinitely (but
the wi(4) driver can recover if you eject the card). The problem is
that the card needs to be "reset" in a way before you even change the
media to hostap. In practice this isn't as noticeable because you
probably do some operation beforehand which prevents the lock-up
before you enable hostap mode.
e.g.:
"ifconfig wi0 up media autoselect mediaopt hostap" will lock up
(if you just inserted the card).
"ifconfig wi0 up ssid foo media autoselect mediaopt hostap" won't lock up.
is really EtherExpress or EEPro or what, but it does appear in a
couple of ethernet cards that have appeared recently on ebay. Silicom
appears to make these cards, and they have the 82595TX chipset in
them, and sometimes uarts. The ex driver needs some work to support
these cards, but I thought I'd get the device into pccarddevs.
The hardware driver decides the name under /dev/led and provides
the function to turn the lamp on/off.
All leds are serviced by a single timeout which runs at a basic rate
of hz/10.
The LED is controlled by ascii strings as follows.
0 Turn off.
1 Turn on.
f Flash: _-
f2 Flash: __--
f3 Flash: ___---
f4...f9 etc.
d%d Digits. "d12": -__________-_-______________________________
s%s String, roll your own:
'a-j' gives on for (1...10)/10 sec.
'A-J' gives on for (1...10)/10 sec.
'sAaAbBa': _-_--__-
m%s Morse
'.' dot
'-' dash
' ' letter space
'\n' word space
My mdoc skills do not reach to express that.
Add a sysctl declaration for hw.ata.atapi_dma, which had gone MIA (though
setting it in loader.conf still worked, it was not visible at runtime)
Approved by: sos
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
GEOM was not designed to handle media that does not have
a size. Blank CD's are of that type, so cheat and set the
media size to -1. This allows burning to work, but makes
GEOM issue outofrange reads that makes the ATAPI subsystem
spew out a few warnings. GEOM should be tought about this.
GEOM was not designed to handle changing the sectorsize
between opens. Writing multitack CD's with both audio and
data tracks needs to change sector size on the fly. We
cheat here and stuff the current sectorsize into GEOM
private internals. GEOM should grow some clean way for this.
o Fix MFC cards. We were bogusly setting CCR_IOBASE[01] and CCR_IOLIMIT.
now when we activate the resource, we adjust these for MFC cards, per the
spec.
o Change type of pf_mfc_* to be bus_addr_t, which is more correct than
long.
This makes my 3C362D/3C363D and 3CXEM556 cards work! Woo Hoo!
o Remove redundant $FreeBSD$
o Better comments about ep_get_macaddr.
o remove one tab in a switch statement (style only)
o Recognize ID 0x0035 as the device ID for the 3CXEM556 that I have. This
makes the 3CXEM556 work for me. Not 100% sure this is the assigned ID,
as I don't have the datasheets for this part, but it does work and get
the correct ethrnet address.
o Comment about the whole fake IRQ 3 thing. some need it, some don't, all
work with it.
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
256 raw receive buffers (96 byte each) fit into one page. This breaks the
limit imposed by the usage of an uint8_t for the buffer number. Restrict
the allocation size for buffers to a maximum of 8192.
are now in the header of the external buffer itself which allows us
to manipulate them in the free routine without having to lock the softc
structure or the free list. To get space for these flags the chunk number
is reduced to 8 bit which amounts to a maximum of 256 chunks per allocated
page. This restriction is now enforced by a CTASSERT.
very first cell in the mbuf should have a cell header word (of which
everything except the payload type and the CLP bit is ignored). All
other cells should be 48 byte and get the same header as the first cell.
This fixes a problem with sending more than 120000 raw cells/sec through
an HE155. The card seems to need 2 cell times to DMA the transmit buffer
ready queue entry and the transmit buffer descriptor so at 1/3 the
link rate the transmit buffer ready queue starts to fill up. Even with this
patch it's obviously impossible to send raw cells at link rate.
Correct a bug when the number of pages for external mbufs was
very large. In this case the page number could overflow into the large
buffer flag. Make this more unlikley by move that flag further away.
is returned from the card to the driver. Add a counter that shows
how many times this allocation has failed. Note, that we could even
further delay the allocation of the mbuf until we know, that we need it
(there are no receive errors and the connection is open). This will be done
in a later commit.
Print the new statistics field in atmconfig.
atomic instructions instead. Remove the stuff used to track
whether an external mbuf travels through the system. This is
temporary only and will come back soon.
the maximum number of pages for buffers) return -1 instead of 0.
This fixes a panic under conditions when many mbufs are needed.
Update the head pointer of the receive buffer pool queue even when
we could not supply a buffer to the chip. Otherwise the chip will
not re-interrupt us for another try. A better strategy would probably
be to remember this condition and to supply buffers without an interrupt
as soon as buffers get available.
Make the pccard attachment work with NEWCARD
Start locking of the driver, but only the macros are defined right now
Tested on: Megahertz CC10BT/2
# (These cards are very popular on ebay these days, and run < $10 including
# shipping from some sellers).
in bufs_info sysctl handler. dev->dma and dev->dma_lock existence are
protected by DRM_LOCK(). Fixes panic on sysctl hw.dri when the device is
uninitialied (when you aren't in X).
dcons(4): very simple console and gdb port driver
dcons_crom(4): FireWire attachment
dconschat(8): User interface to dcons
Tested with: i386, i386-PAE, and sparc64.
giant, which implies that we need to take out giant it we're NOT
MPSAFE.
# I can't believe the number of people that looked at this failed to
# detect this.
locking, and the apparently unnecessary locking for -stable has been removed.
This may fix issues with missed interrupts since April, which manifested
themselves as slowdowns or hangs in radeon, in particular. Many cleanups also
took place. In the shared code, there are improvements to r128 driver
stability.
part of the support is that it still assumes one master and one target
where as AGP 3.0 actually supports multiple devices on the bus.
Submitted by: Keith Whitwell <keith@tungstengraphics.com>
Sponsored by: The Weather Channel
Until we can have perfect knowledge that all callers above us think it's okay
for us to sleep, releasing *our* locks of course, we don't dare try and sleep.
in connection with Marvell based SATA->PATA dongles.
The problem was caused by a combination of things working
together to make it hard to spot...
The ATA driver has always started the ATA command, then build
the SG list for DMA and then finally started the DMA engine.
While this is according to specs, it poses a potential
problem as some controllers apparently do not allow for unlimitted
time between starting the ATA command and starting the DMA engine.
At about the same time as ATAng was committed there were lots
of other changes applied, some of which was locking in parts
that causes the busdma load functions to take significantly
longer to load the SG list.
This pushed the time spent between starting the ATA command and
starting the DMA engine over the hill for some controllers
(especially the Silicon Image DS3112a) and caused what looked
like lost interrupts.
The solution is to get all the SG list work or rather all
busdma related stuff done before we even try to start anything.
This has the nice side effect of seperating busdma out the
way it should be, so the working of the ATA machinery is not
cluttered up with busdma droppings, making the code easier
to read and understand.
chain passed into dc_encap, which dc_start was unaware of. This caused
the old (now invalid) mbuf to be passed to BPF_MTAP.
Spotted by: Kenjiro Cho <kjc@csl.sony.co.jp>
table, acquiring the necessary locks as it works. It usually returns
two references to the new descriptor: one in the descriptor table
and one via a pointer argument.
As falloc releases the FILEDESC lock before returning, there is a
potential for a process to close the reference in the file descriptor
table before falloc's caller gets to use the file. I don't think this
can happen in practice at the moment, because Giant indirectly protects
closes.
To stop the file being completly closed in this situation, this change
makes falloc set the refcount to two when both references are returned.
This makes life easier for several of falloc's callers, because the
first thing they previously did was grab an extra reference on the
file.
Reviewed by: iedowse
Idea run past: jhb
Use EP_{READ,WRITE}{,_MULTI}_{1,2,4} instead. I've had several people
submit patches like this over the years of varying qualities, markm
being the last. The names were chosen in consulation with mdodd on
irc.
I've tested this with only PCMCIA cards: 3CCE589EC and 3CCSH572BT.
I've not tried with my more extensive ISA, EISA and cbus collection.
Reviewed by: mdodd
Though this is still incomplete and has some missing features such as
exclusive login and event notification, it may be enough for someone
who wants to play with it.
This driver is supposed to work with firewire(4), targ(4) of CAM(4)
and scsi_target(8) which can be found in /usr/share/example/scsi_target.
This driver doesn't require sbp(4) which implements initiator mode.
Sample configuration:
Kernel: (you can use modules as well)
device firewire
device scbus
device targ
device sbp_targ
After reboot:
# mdconfig -a -t malloc -s 10m
md0
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
You should find the 10MB HDD on FreeBSD/MacOS X/WinXP or whatever connected
to the target using FireWire.
Manpage is not finished yet.
- Change type of target->luns to allocate an array of LUNs dynamically.
This allows targets to change their number of LUNs after each bus reset.
- Serialize ORB POINTER command for each LUN.
- Improve debug messages.
- Correct the logic for the AIF array index pointers so that correct slot is
always looked at.
- Copy the full FIB payload size when copying AIF's, not just the first 64
bytes.
Thanks to Mirapoint, Inc, for pointing these problems out and offering a
solution.
Discussed in from [FreeBSD-tech-jp 3396] to [FreeBSD-tech-jp 3407]
at FreeBSD-tech-jp@jp.freebsd.org.
NOTE: We must put ed_probe_SIC() function into if_ed_isa.c because
this is a bus dependent code. But the ed driver code is not
separated explicitly whether it is bus dependent or independent
now.
Refer to: http://plaza17.mbn.or.jp/~chi/myprog/FreeBSD/sicat.html
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
lock around a call to the original function. Make the timeout
function in callout_reset() use the wrapped function to avoid a
lock assertion panic.
Reviewed by: sam
Reported by: cgiordano@ids.net
- Make multicast work
- Fix (some of) the watchdog timeouts after card reset
- Add support for CE2, CEM28 and CEM33 cards
- General code cleanup
Any card that worked previously should still work, as well as a lot that
didn't.
The driver is not yet style(9) compliant; those changes are forthcoming,
once the functional changes are done.
PR: kern/50644
Reviewed by: imp
Approved by: imp
timeout would continue to happen: boom! Fix this[*] by timing out earlier.
[*] almost fixes the race on unload: wi_inquire could be running when
untimeout is called, and there's no way to know when it has actually
returned. This race is very rare and hard to lose.
Submitted by: scottl
seeded with arc4random rather than calling arc4random for each
packet. Note this is the same algorithm used to select the IV when
doing WEP on the host.
o don't grab the mutex at the top of ath_detach; it does nothing
useful
o deal with entry to ath_ioctl during detach to disable promiscuous
mode as a result of calling bpfdetach2: cannot call ath_init when
the device is marked invalid as the code isn't prepared to deal
with it (in particular by that time the hal reference may have
been yanked)
change ath_rate_ctl_reset to handle transition from station
mode to adhoc mode; was not resetting the initial xmit rate
causing outbound frames to be dicarded
parameter in the read and write case dereferenced an unitialized
pointer and can't possibly ever have catched an actual invalid
argument.
This was apparently true for the read/write and getconf cases. The
latter does not even receive the paramter that is to be verified.
I'm surprised that this did not cause kernel panics, but it seems
that the uninitialized local variable happens to contain data that
may be used as a pointer to memory that satisfies the test condition.
Make the code work as intended by moving the test inside the switch
case where the pointer has been properly initialized.
Since the read and write case shared just about all code (except
for the single call to PCIB_READ_CONFIG resp. PCIB_WRITE_CONFIG) I
have merged both cases.
Noticed by: trhodes@FreeBSD.org (Tom Rhodes)
o correct recursive locking when polling and in em_82547_move_tail
o destroy mutex on detach
o add EM_LOCK_ASSERT and similar macros for creating+deleteing the mtx
Submitted by: Daniel Eischen <eischen@vigrid.com>
beasts which are reported to exist in both Atmel and Prism2 flavours. In
particular, Itronix branded laptops have the Atmel part with an Intersil
radio.
Obtained from: NetBSD
o minor optimization of cardbus_cis processing. Remove a bunch of generic
entries that are handled by generic.
o no longer need the card_get_type stuff.
This MIB specifies how many bus resets should be observed before the
lost device entry is removed. The default value is 3.
You can set this value to 0 if you want a SBP device to be detached from CAM
layer as soon as the device is physically detached like USB.
routine of its own, and allows us to move the indentation back two
layers making the code more readable.
delete a prototype that should have been killed years ago in pccardvar.h.
# adding quirks here is way harder than it needs to be. :-(
In unodered excution case, we cannot detect link-chain end only
by prev == NULL if lastest ORB is executed earlyer than the former
ORBs. Use ORB_LINK_DEAD flag for this case.
- Don't reset agent for management ORB.
- Improve debug messages.
Spotted by: sbp target mode
for 21143 based cards which use SIA mode.
This fixes 10mbit mode for ZNYX ZX346Q cards and other
21143 based cards.
PR: 32118
Submitted by: Rene de Vries <rene@tunix.nl>
Geert Jan de Groot <GeertJan.deGroot@tunix.nl>
Obtained from: BSDI
MFC after: 2 weeks
