but can be enabled by setting hw.atm.hatmN.mpsafe in the kernel
environment to a non-zero value before loading the driver. When
the problems with network MPSAFEty have been sorted out this will
be removed and the driver will default to MPSAFE.
We put them directly onto the free list instead of calling the
external mbuf free routine (that routine would have cleaned the flag).
This fixes a bug which manifests itself in falsely reporting a lot of used
buffers when configuring the interface down.
from the xe driver. Should probably be removed when current probe/attach
problems with the driver are fixed, but is useful now when requesting
diagnostic information from users.
Reviewed by: imp (mentor)
o Fix minor type problems
o Fix minor problem with a couple debug printfs.
o Default to a sane media type when none is reported.
o Minor style changes
The PR complains this will fix the IBM 300GL cards.
Submitted by: Max Gotlib
PR: 11462
operating mode to HostAP, the card will lock up indefinitely (but
the wi(4) driver can recover if you eject the card). The problem is
that the card needs to be "reset" in a way before you even change the
media to hostap. In practice this isn't as noticeable because you
probably do some operation beforehand which prevents the lock-up
before you enable hostap mode.
e.g.:
"ifconfig wi0 up media autoselect mediaopt hostap" will lock up
(if you just inserted the card).
"ifconfig wi0 up ssid foo media autoselect mediaopt hostap" won't lock up.
is really EtherExpress or EEPro or what, but it does appear in a
couple of ethernet cards that have appeared recently on ebay. Silicom
appears to make these cards, and they have the 82595TX chipset in
them, and sometimes uarts. The ex driver needs some work to support
these cards, but I thought I'd get the device into pccarddevs.
The hardware driver decides the name under /dev/led and provides
the function to turn the lamp on/off.
All leds are serviced by a single timeout which runs at a basic rate
of hz/10.
The LED is controlled by ascii strings as follows.
0 Turn off.
1 Turn on.
f Flash: _-
f2 Flash: __--
f3 Flash: ___---
f4...f9 etc.
d%d Digits. "d12": -__________-_-______________________________
s%s String, roll your own:
'a-j' gives on for (1...10)/10 sec.
'A-J' gives on for (1...10)/10 sec.
'sAaAbBa': _-_--__-
m%s Morse
'.' dot
'-' dash
' ' letter space
'\n' word space
My mdoc skills do not reach to express that.
Add a sysctl declaration for hw.ata.atapi_dma, which had gone MIA (though
setting it in loader.conf still worked, it was not visible at runtime)
Approved by: sos
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
GEOM was not designed to handle media that does not have
a size. Blank CD's are of that type, so cheat and set the
media size to -1. This allows burning to work, but makes
GEOM issue outofrange reads that makes the ATAPI subsystem
spew out a few warnings. GEOM should be tought about this.
GEOM was not designed to handle changing the sectorsize
between opens. Writing multitack CD's with both audio and
data tracks needs to change sector size on the fly. We
cheat here and stuff the current sectorsize into GEOM
private internals. GEOM should grow some clean way for this.
o Fix MFC cards. We were bogusly setting CCR_IOBASE[01] and CCR_IOLIMIT.
now when we activate the resource, we adjust these for MFC cards, per the
spec.
o Change type of pf_mfc_* to be bus_addr_t, which is more correct than
long.
This makes my 3C362D/3C363D and 3CXEM556 cards work! Woo Hoo!
o Remove redundant $FreeBSD$
o Better comments about ep_get_macaddr.
o remove one tab in a switch statement (style only)
o Recognize ID 0x0035 as the device ID for the 3CXEM556 that I have. This
makes the 3CXEM556 work for me. Not 100% sure this is the assigned ID,
as I don't have the datasheets for this part, but it does work and get
the correct ethrnet address.
o Comment about the whole fake IRQ 3 thing. some need it, some don't, all
work with it.
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
256 raw receive buffers (96 byte each) fit into one page. This breaks the
limit imposed by the usage of an uint8_t for the buffer number. Restrict
the allocation size for buffers to a maximum of 8192.
are now in the header of the external buffer itself which allows us
to manipulate them in the free routine without having to lock the softc
structure or the free list. To get space for these flags the chunk number
is reduced to 8 bit which amounts to a maximum of 256 chunks per allocated
page. This restriction is now enforced by a CTASSERT.
very first cell in the mbuf should have a cell header word (of which
everything except the payload type and the CLP bit is ignored). All
other cells should be 48 byte and get the same header as the first cell.
This fixes a problem with sending more than 120000 raw cells/sec through
an HE155. The card seems to need 2 cell times to DMA the transmit buffer
ready queue entry and the transmit buffer descriptor so at 1/3 the
link rate the transmit buffer ready queue starts to fill up. Even with this
patch it's obviously impossible to send raw cells at link rate.
Correct a bug when the number of pages for external mbufs was
very large. In this case the page number could overflow into the large
buffer flag. Make this more unlikley by move that flag further away.
is returned from the card to the driver. Add a counter that shows
how many times this allocation has failed. Note, that we could even
further delay the allocation of the mbuf until we know, that we need it
(there are no receive errors and the connection is open). This will be done
in a later commit.
Print the new statistics field in atmconfig.
atomic instructions instead. Remove the stuff used to track
whether an external mbuf travels through the system. This is
temporary only and will come back soon.
the maximum number of pages for buffers) return -1 instead of 0.
This fixes a panic under conditions when many mbufs are needed.
Update the head pointer of the receive buffer pool queue even when
we could not supply a buffer to the chip. Otherwise the chip will
not re-interrupt us for another try. A better strategy would probably
be to remember this condition and to supply buffers without an interrupt
as soon as buffers get available.
Make the pccard attachment work with NEWCARD
Start locking of the driver, but only the macros are defined right now
Tested on: Megahertz CC10BT/2
# (These cards are very popular on ebay these days, and run < $10 including
# shipping from some sellers).
in bufs_info sysctl handler. dev->dma and dev->dma_lock existence are
protected by DRM_LOCK(). Fixes panic on sysctl hw.dri when the device is
uninitialied (when you aren't in X).
dcons(4): very simple console and gdb port driver
dcons_crom(4): FireWire attachment
dconschat(8): User interface to dcons
Tested with: i386, i386-PAE, and sparc64.
giant, which implies that we need to take out giant it we're NOT
MPSAFE.
# I can't believe the number of people that looked at this failed to
# detect this.
locking, and the apparently unnecessary locking for -stable has been removed.
This may fix issues with missed interrupts since April, which manifested
themselves as slowdowns or hangs in radeon, in particular. Many cleanups also
took place. In the shared code, there are improvements to r128 driver
stability.
part of the support is that it still assumes one master and one target
where as AGP 3.0 actually supports multiple devices on the bus.
Submitted by: Keith Whitwell <keith@tungstengraphics.com>
Sponsored by: The Weather Channel
Until we can have perfect knowledge that all callers above us think it's okay
for us to sleep, releasing *our* locks of course, we don't dare try and sleep.
in connection with Marvell based SATA->PATA dongles.
The problem was caused by a combination of things working
together to make it hard to spot...
The ATA driver has always started the ATA command, then build
the SG list for DMA and then finally started the DMA engine.
While this is according to specs, it poses a potential
problem as some controllers apparently do not allow for unlimitted
time between starting the ATA command and starting the DMA engine.
At about the same time as ATAng was committed there were lots
of other changes applied, some of which was locking in parts
that causes the busdma load functions to take significantly
longer to load the SG list.
This pushed the time spent between starting the ATA command and
starting the DMA engine over the hill for some controllers
(especially the Silicon Image DS3112a) and caused what looked
like lost interrupts.
The solution is to get all the SG list work or rather all
busdma related stuff done before we even try to start anything.
This has the nice side effect of seperating busdma out the
way it should be, so the working of the ATA machinery is not
cluttered up with busdma droppings, making the code easier
to read and understand.
chain passed into dc_encap, which dc_start was unaware of. This caused
the old (now invalid) mbuf to be passed to BPF_MTAP.
Spotted by: Kenjiro Cho <kjc@csl.sony.co.jp>
table, acquiring the necessary locks as it works. It usually returns
two references to the new descriptor: one in the descriptor table
and one via a pointer argument.
As falloc releases the FILEDESC lock before returning, there is a
potential for a process to close the reference in the file descriptor
table before falloc's caller gets to use the file. I don't think this
can happen in practice at the moment, because Giant indirectly protects
closes.
To stop the file being completly closed in this situation, this change
makes falloc set the refcount to two when both references are returned.
This makes life easier for several of falloc's callers, because the
first thing they previously did was grab an extra reference on the
file.
Reviewed by: iedowse
Idea run past: jhb
Use EP_{READ,WRITE}{,_MULTI}_{1,2,4} instead. I've had several people
submit patches like this over the years of varying qualities, markm
being the last. The names were chosen in consulation with mdodd on
irc.
I've tested this with only PCMCIA cards: 3CCE589EC and 3CCSH572BT.
I've not tried with my more extensive ISA, EISA and cbus collection.
Reviewed by: mdodd
Though this is still incomplete and has some missing features such as
exclusive login and event notification, it may be enough for someone
who wants to play with it.
This driver is supposed to work with firewire(4), targ(4) of CAM(4)
and scsi_target(8) which can be found in /usr/share/example/scsi_target.
This driver doesn't require sbp(4) which implements initiator mode.
Sample configuration:
Kernel: (you can use modules as well)
device firewire
device scbus
device targ
device sbp_targ
After reboot:
# mdconfig -a -t malloc -s 10m
md0
# scsi_target 0:0:0 /dev/md0
(Assuming sbp_targ0 on scbus0)
You should find the 10MB HDD on FreeBSD/MacOS X/WinXP or whatever connected
to the target using FireWire.
Manpage is not finished yet.
- Change type of target->luns to allocate an array of LUNs dynamically.
This allows targets to change their number of LUNs after each bus reset.
- Serialize ORB POINTER command for each LUN.
- Improve debug messages.
- Correct the logic for the AIF array index pointers so that correct slot is
always looked at.
- Copy the full FIB payload size when copying AIF's, not just the first 64
bytes.
Thanks to Mirapoint, Inc, for pointing these problems out and offering a
solution.
Discussed in from [FreeBSD-tech-jp 3396] to [FreeBSD-tech-jp 3407]
at FreeBSD-tech-jp@jp.freebsd.org.
NOTE: We must put ed_probe_SIC() function into if_ed_isa.c because
this is a bus dependent code. But the ed driver code is not
separated explicitly whether it is bus dependent or independent
now.
Refer to: http://plaza17.mbn.or.jp/~chi/myprog/FreeBSD/sicat.html
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
lock around a call to the original function. Make the timeout
function in callout_reset() use the wrapped function to avoid a
lock assertion panic.
Reviewed by: sam
Reported by: cgiordano@ids.net
- Make multicast work
- Fix (some of) the watchdog timeouts after card reset
- Add support for CE2, CEM28 and CEM33 cards
- General code cleanup
Any card that worked previously should still work, as well as a lot that
didn't.
The driver is not yet style(9) compliant; those changes are forthcoming,
once the functional changes are done.
PR: kern/50644
Reviewed by: imp
Approved by: imp
timeout would continue to happen: boom! Fix this[*] by timing out earlier.
[*] almost fixes the race on unload: wi_inquire could be running when
untimeout is called, and there's no way to know when it has actually
returned. This race is very rare and hard to lose.
Submitted by: scottl
seeded with arc4random rather than calling arc4random for each
packet. Note this is the same algorithm used to select the IV when
doing WEP on the host.
o don't grab the mutex at the top of ath_detach; it does nothing
useful
o deal with entry to ath_ioctl during detach to disable promiscuous
mode as a result of calling bpfdetach2: cannot call ath_init when
the device is marked invalid as the code isn't prepared to deal
with it (in particular by that time the hal reference may have
been yanked)
change ath_rate_ctl_reset to handle transition from station
mode to adhoc mode; was not resetting the initial xmit rate
causing outbound frames to be dicarded
parameter in the read and write case dereferenced an unitialized
pointer and can't possibly ever have catched an actual invalid
argument.
This was apparently true for the read/write and getconf cases. The
latter does not even receive the paramter that is to be verified.
I'm surprised that this did not cause kernel panics, but it seems
that the uninitialized local variable happens to contain data that
may be used as a pointer to memory that satisfies the test condition.
Make the code work as intended by moving the test inside the switch
case where the pointer has been properly initialized.
Since the read and write case shared just about all code (except
for the single call to PCIB_READ_CONFIG resp. PCIB_WRITE_CONFIG) I
have merged both cases.
Noticed by: trhodes@FreeBSD.org (Tom Rhodes)
o correct recursive locking when polling and in em_82547_move_tail
o destroy mutex on detach
o add EM_LOCK_ASSERT and similar macros for creating+deleteing the mtx
Submitted by: Daniel Eischen <eischen@vigrid.com>
beasts which are reported to exist in both Atmel and Prism2 flavours. In
particular, Itronix branded laptops have the Atmel part with an Intersil
radio.
Obtained from: NetBSD
o minor optimization of cardbus_cis processing. Remove a bunch of generic
entries that are handled by generic.
o no longer need the card_get_type stuff.
This MIB specifies how many bus resets should be observed before the
lost device entry is removed. The default value is 3.
You can set this value to 0 if you want a SBP device to be detached from CAM
layer as soon as the device is physically detached like USB.
routine of its own, and allows us to move the indentation back two
layers making the code more readable.
delete a prototype that should have been killed years ago in pccardvar.h.
# adding quirks here is way harder than it needs to be. :-(
In unodered excution case, we cannot detect link-chain end only
by prev == NULL if lastest ORB is executed earlyer than the former
ORBs. Use ORB_LINK_DEAD flag for this case.
- Don't reset agent for management ORB.
- Improve debug messages.
Spotted by: sbp target mode
for 21143 based cards which use SIA mode.
This fixes 10mbit mode for ZNYX ZX346Q cards and other
21143 based cards.
PR: 32118
Submitted by: Rene de Vries <rene@tunix.nl>
Geert Jan de Groot <GeertJan.deGroot@tunix.nl>
Obtained from: BSDI
MFC after: 2 weeks
And many changes.
* all
- Major change of struct fw_xfer.
o {send,recv}.buf is splitted into hdr and payload.
o Remove unnecessary fields.
o spd is moved under send and recv.
- Remove unnecessary 'volatile' keyword.
- Add definition of rtcode and extcode.
* firewire.c
- Ignore FWDEVINVAL devices in fw_noderesolve_nodeid().
- Check the existance of the bind before call STAILQ_REMOVE().
- Fix bug in the fw_bindadd().
- Change element of struct fw_bind for simplicity.
- Check rtcode of response packet.
- Reduce split transaction timeout to 200 msec.
(100msec is the default value in the spec.)
- Set watchdog timer cycle to 10 Hz.
- Set xfer->tv just before calling fw_get_tlabel().
* fwohci.c
- Simplifies fwohci_get_plen().
* sbp.c
- Fix byte order of multibyte scsi_status informations.
- Split sbp.c and sbp.h.
- Unit number is not necessary for FIFO¤ address.
- Reduce LOGIN_DELAY and SCAN_DELAY to 1 sec.
- Add some constants defineded in SBP-2 spec.
* fwmem.c
- Introduce fwmem_strategy() and reduce memory copy.
was that accessing the status reg could occour too fast, confusing
the logic in the flash part. Could not have been located without:
HW donated by: Jonas Bülow <jonas@servicefactory.se>
AcpiEnterSleepState() calling a long AcpiOsStall() with interrupts
disabled. This fix will instead be added to ACPI-CA.
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
make sure we return any allocated space to the drive. This should get
rid of a number of inconsistencies (hopefully all) that have been seen
after configuration errors.
even could call VOP_REVOKE() on vnodes associated with its dev_t's
has originated, but it stops right here.
If there are things people belive destroy_dev() needs to learn how to
do, please tell me about it, preferably with a reproducible test case.
Include <sys/uio.h> in bluetooth code rather than rely on <sys/vnode.h>
to do so.
The fact that some of the USB code needs to include <sys/vnode.h>
still disturbs me greatly, but I do not have time to chase that.
from fiddling with CS_TTGO since fiddling with CS_TTGO was removed in
rev.1.218 of the i386/isa version (which was merged with loss of history
in rev.1.223 of this version).
This is just a cleanup here (modulo rev.1.108 of kern/tty.c), since the
input speed can be different from to output speed and extra code to
handle both speeds naturally handled all cases.
provide no methods does not make any sense, and is not used by any
driver.
It is a pretty hard to come up with even a theoretical concept of
a device driver which would always fail open and close with ENODEV.
Change the defaults to be nullopen() and nullclose() which simply
does nothing.
Remove explicit initializations to these from the drivers which
already used them.
- Removed conversion of a zero input speed to the output speed. This
has been done better in ttioctl() since rev.1.108 of kern/tty.c
almost 5 years ago. comparam() did the conversion incompletely for
the case where the output speed is also zero. It had complications
to avoid using zero speeds, but would still have used a zero input
speed for setting watermarks if kern/tty.c had passed one.
- Never permit the input speed to be different from the output speed.
There was no validity check on the input speed for the case of a zero
output speed. Then we didn't change the physical speeds, but we used
the unvalidated input speed for setting watermarks and didn't return
an error, so ttioctl() stored the unvalidated input speed in the tty
struct where it could cause problems later.
- Removed complications that were to avoid using a divisor of 0. The
divisor is now always valid if the speed is accepted.
cd_setreg() were still using !(read_eflags() & PSL_I) as the condition
for the lock hidden by COM_LOCK() (if any) being held. This worked
when spin mutexes and/or critical_enter() used hard interrupt disablement,
but it has caused recursion on the non-recursive mutex com_mtx since
all relevant interrupt disablement became soft. The recursion is
harmless unless there are other bugs, but it breaks an invariant so
it is fatal if spinlocks are witnessed.
in the loopback test in the probe. The delay was too short for consoles
at speeds lower than about 3200 bps. This shouldn't have caused many
problems, since such low speeds are rare and the probe is forced to
succeed for consoles.
and the Z8530 drivers used the I/O address as a quick and dirty way to
determine which channel they operated on, but formalizing this by
introducing iobase is not a solution. How for example would a driver
know which channel it controls for a multi-channel UART that only has a
single I/O range?
Instead, add an explicit field, called chan, to struct uart_bas that
holds the channel within a device, or 0 otherwise. The chan field is
initialized both by the system device probing (i.e. a system console)
or it is passed down to uart_bus_probe() by any of the bus front-ends.
As such, it impacts all platforms and bus drivers and makes it a rather
large commit.
Remove the use of iobase in uart_cpu_eqres() for pc98. It is expected
that platforms have the capability to compare tag and handle pairs for
equality; as to determine whether two pairs access the same device or
not. The use of iobase for pc98 makes it impossible to formalize this
and turn it into a real newbus function later. This commit reverts
uart_cpu_eqres() for pc98 to an unimplemented function. It has to be
reimplemented using only the tag and handle fields in struct uart_bas.
Rewrite the SAB82532 and Z8530 drivers to use the chan field in struct
uart_bas. Remove the IS_CHANNEL_A and IS_CHANNEL_B macros. We don't
need to abstract anything anymore.
Discussed with: nyan
Tested on: i386, ia64, sparc64
aic7xxx_pci.c:
When performing our register test, be careful
to avoid resetting the chip when pausing the
controller. The test reads the HCNTRL register
and then writes it back with the PAUSE bit
explicitly set. If the last write to the controller
before our probe is to reset it, the CHIPRST
bit will still be set, so we must mask it off
before the PAUSE operation. On some chip versions,
we cannot access registers for a few 100us after
a reset, so this inadvertant reset was causing PCI
errors to occur on the read to check for paused
status.
Submitted by: gibbs
Instead, use EXCA_MEMREG_WIN_SHIFT which is the amount we shift the
bus address by to write into upper memory (eg above 24MB). Use the
latter in this case.
1.186: onoe; Sony's PEGA-WL110 CF WLAN (which strangely has fujitsu's
vendor id)
1.185: ichiro; Quatech Inc, PCMCIA Enhanced Parallel Port Card
Also:
o update $NetBSD$
o minor tweaks to FUJITSU. We've tried to keep the CIS only entries seprate
from vendor id/product id.
Fix to the messages output under CAM_DEBUG_CCB: the summary sense
information (error bits and sense key) is in the error field, not
in the result field, of struct ata_request. No other functional change.
device to access 64-bit addresses from a 32-bit PCI bus. While the
RealTek manual says you can set this bit and the chip will perform
DAC only if you give it a DMA address with any of the upper 32
bits set, this appears not to be the case. If I turn on the DAC
bit, the chip sets the 'system error' bit in the status register
when I to do a DMA on my Athlon test box with 32-bit PCI bus (VIA
chipset) even though I only have 128MB of physical memory, and thus
can never give the chip a 64-bit address.
Obviously, I can't just set it and forget it, so until I figure
out the right rule for when it's safe/necessary to enable it, keep
it turned off.
Tested at 100Mbit only, using Asus P4P800 onboard 3C940.
The -stable version of this patch I have in use for ~2 weeks now, and works
just fine for me.
Based on: Nathan L. Binkert's patch for OpenBSD
Patch submitted by and thanks to: Jung-uk Kim <jkim@niksun.com>
MFC after: 2 weeks
IF_HANDOFF() does it for us behind the scenes. Remove the extra call
to re_start() otherwise we try to transmit twice.
In re_encap(), fix the code that guards against consuming too many
descriptors in the TX ring so that it actually works. With the
new 8169S chip, I was able to hit a corner case that drained the
free descriptor count all the way to 0. This is not supposed to
be possible.
COM_NOFIFO() and COM_ESP cases are supposed to be a subsets of the
plain 16550A case, but 16650-related changes made the former fall into
the latter and then both fall into general code for printing the tx
fifo size. This mainly caused hard to parse boot messages like:
"sio0: type 16550A fifo disabled lookalike with 1 bytes FIFO".
COM_NOFIFO() on an ESP port gave a larger mess whose extent is not
clear.
Fixed some nearby style bugs.
defined values instead of hard-coded values. Don't repeat the register
access part of the code 4 times times or triple-space statements. This
fixes half of the style bugs in rev.1.172.
Hardware flow control of 16650As is still officially unsupported. I
was mistaken about it being broken. It is broken in 16650s but is
fixed in 16650As except for the maximum trigger level (which is no
longer used). Testing of the 16650's broken hardware flow control
watermarks by programming them on 16950s showed that their effects are
not too bad if the fifo size and trigger level are reasonably large
(16 is much better than 8).
an UART interface could get stuck when a new interrupt condition
arose while servicing a previous interrupt. Since an interrupt was
already pending, no new interrupt would be triggered.
Avoid infinite recursion by flushing the Rx FIFO and marking an
overrun condition when we could not move the data from the Rx
FIFO to the receive buffer in toto. Failure to flush the Rx FIFO
would leave the Rx ready condition pending.
Note that the SAB 82532 already did this due to the nature of the
chip.
precisely where locking would be needed before adding it, but it
seems uart(4) draws slightly too much attention to have it without
locking for too long.
The lock added is a spinlock that protects access to the underlying
hardware. As a first and obvious stab at this, each method of the
hardware interface grabs the lock. Roughly speaking this serializes
the methods. Exceptions are the probe, attach and detach methods.
a problem for command responses since we rarely ever filled the queue.
However, adapter-initiated commands have a much smaller queue and could
tickle this bug. It's possible that this might fix the recently reported
problems with the aac-2120s, though I haven't been able to reproduce the
problem locally.
MFC-After: 1 day
and some of their bits (i.e., fifo trigger levels, frequency multipliers
and divisors, and bits to select the registers for these). This
attempts to completely describe the 16950's complicated register selects
for 16950-specific registers only.
the description of the data latch registers (they were described as
readonly).
Added some better and worse aliases for standard registers, mostly taken
from the 16950 data sheet. Define deprecated aliases in terms of the
preferred one.
Don't define com_efr in terms of com_fifo. It is unrelated (in a
different bank).
Merged comments to match (put them at the right of the #defines instead
of duplicating them).
Sorted the resulting sections on UART type and register bank. Added a
comment for each bank.
to ns16550.h. The organization of these files was sort of backwards.
The bits in the registers have no driver or bus dependencies but they
but the offsets of the registers in bus space are very bus-dependent.
However, it does no harm to keep the definitions of the register offsets
in ns16550.h provided they are thought of as internal ns*50 offsets.
that has been recorded earlier and overwrite it again later by
reading it directly from the EEPROM again.
Read the MAC address from the PAR0/PAR1 registers instead, which
are autoloaded on reboot.
Tested on AN985, AN983B. According to the datasheets, it should
also work for the AL981 (I don't have such a chip on a card at home)
PR: 52988
Submitted by: Andrew Gordon <arg-bsd@arg.me.uk>
MFC after: 2 weeks
calculate smoothed signal quality data for each node.
o add a 16-deep history buffer to each driver-private node storage that
holds rssi and antenna info for received frames
o override the default per-node "get rssi" method to return an average
rssi value based on samples collected over the last second
o enable beacon reception so even idle systems maintain a running history
of signal quality
This data may also be useful for improving the rate control algorithm.
Based on work by Tom Marshall <tommy@home.tig-grr.com> for MADWIFI.
to the 802.11 layer if they are at least IEEE80211_MIN_LEN
o mask off interrupt status bits that we don't care about so we don't do
the wrong thing; this fixes a problem where the beacon miss interrupt status
bit is delivered together with other status bits when operating in monitor
mode (we would post a beacon miss swi and then do the wrong thing)
was added to the fast path to support the COM_IIR_RXRDYBUG() case even
when that case is not configured. This increased the relative overhead
of sio input by almost 25% in the worst case and by 2-3% in the usual
case (usually only about 0.2% absolute per port at 115200 bps). The
quick fix is to significantly pessimize only the COM_IIR_RXRDYBUG()
case.
safe since the 802.11 layer does the right thing for 11a operation)
o select short preamble operation based on the negotiated capabilities; not
just the local state/capability
o fillin the duration field in the 802.11 header as appropriate
o remove detection of 11g support; no longer needed
Obtained from: MADWIFI (with modifications)
we're on a 32-bit/64-bit bus or not. Use this to decide if we should
set the PCI dual-address cycle enable bit in the C+ command register.
(Enabling DAC on a 32-bit bus seems to do bad things.)
Also, initialize the C+ command register early in the re_init() routine.
The documentation says this register should be configured first.
We simply use the detected FIFO size to determine whether we have
a post 16550 UART or not. The support lacks proper serialization of
hardware access for now.
fixes a longstanding issue WRT resetting the chip after startup- it
would fail if we were connected as an F-port to a switch. If we
were connected as an F-port, we got assigned a hard loop ID of 255,
which is really a bogus loop id. Then when we turned around to
reset ourselves, the firmware would reject the ICB_INIT request
because the loop id was bogus. *sputter*
Minor fixlet from somebody in NetBSD with too much time on their
hands (dma -> DMA).
the "compatible" property too in the ns8250 case. This gets the serial
console to work on Blade 100s, where the device name is just "serial".
Reviewed by: marcel
Second (PPS) timing interface. The support is non-optional and by
default uses the DCD line signal as the pulse input. A compile-time
option (UART_PPS_ON_CTS) can be used to have uart(4) use the CTS line
signal.
Include <sys/timepps.h> in uart_bus.h to avoid having to add the
inclusion of that header in all source files.
Reviewed by: phk
This commit puts the relevant code snippets under #ifdef GONE_IN_5
(rather than #ifndef BURN_BRIDGES) thereby disabling the code now.
The code wil be entirely removed before 5.2 unless we find reasons
why this would be a bad idea.
Approach suggested by: imp
seems to be necessary for the 8139C+ under certain circumstances, and
doesn't appear to hurt the other chips. (In the failure case, the
packet would be sent through the TX DMA ring but not get echoed
back. I suspect this has something to do with the link state changing
unexpectedly.)
autoload and then copying the contends of the station address
registers. For some reason, reading the EEPROM on the 8169S doesn't
work right. This gets around the problem, and allows us to read
the station address correctly on the 8169S.
- Insert a delay after initiating packet transmition in re_diag() to
allow lots of time for the frame to echo back to the host, and wait
for both the 'RX complete' and 'timeout expired' bits in the ISR
register to be set.
- Deal more intelligently with the fact that the frame length
field in the RX descriptor is a different width on the 8139C+
than it is on the 8169/8169S/8110S
- For the 8169, you have to set bit 17 in the TX config register
to enter digital loopback mode, but for the 8139C+, you have to
set both bits 17 and 18. Take this into account so that re_diag()
works properly for both types of chips.
ethernet chips. This driver is pretty simple, however it contains
special DSP initialization code which is needed in order to get
the chip to negotiate a gigE link. (This special initialization
may not be needed in subsequent chip revs.) Also:
- Fix typo in if_rlreg.h (RL_GMEDIASTAT_1000MPS -> RL_GMEDIASTAT_1000MBPS)
- Deal with shared interrupts in re_intr(): if interface isn't up,
return.
- Fix another bug in re_gmii_writereg() (properly apply data field mask)
- Allow PHY driver to read the RL_GMEDIASTAT register via the
re_gmii_readreg() register (this is register needed to determine
real time link/media status).
method. This is necessary on ia64 where it's known that serial interfaces
described in the ACPI namespace may not have the well-known IRQs assigned
to them. This confuses us in thinking they are PCI based interrupts and
wrongly program the APIC.
for the 8169S, according to my sample board. The RealTek Linux driver
mentions 0x00800000. I'm assigning this to the 8110S until I get
more info on it. (The (preliminary) RealTek docs only say that 8169S/8110S
chips will have some combination of those two bits set, but doesn't say
exactly what bit combination goes with which chip variant.)
is not a size of 1. Since we already know there is a FIFO, we can
safely assume that it is at least 16 bytes. Note that all this is
mostly academic anyway. We don't use the size of the Rx FIFO
currently. If we add support for hardware flow control, we only
care about Rx FIFO sizes larger than 16.
written by Stuart Walsh and Duncan Barclay (with some kibbitzing by
me). I'm checking it in on Stuart's behalf.
The BCM4401 is built into several x86 laptop and desktop systems. For the
moment, I have only enabled it in the x86 kernel config because although
it's a PCI device, I haven't heard of any standalone NICs that use it. If
somebody knows of one, we can easily add it to the other arches.
This driver uses register/structure data gleaned from the Linux
driver released by Broadcom, but does not contain any of the code
from the Linux driver itself. It uses busdma.
rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
from the SAB82532 and the Z8530 hardware drivers by introducing
uart_cpu_busaddr(). The assumption is not true on pc98 where
bus_space_handle_t is a pointer to a structure.
The uart_cpu_busaddr() function will return the bus address
corresponding the tag and handle given to it by the BAS.
WARNING: the intend of the function is STRICTLY to allow hardware
drivers to determine which logical channel they control and is NOT
to be used for actual I/O. It is therefore EXPLICITLY allowed that
uart_cpu_busaddr() returns only the lower 8 bits of the address
and garbage in all other bits. No mistakes...
(ns8250 copied and s/ns8250/i8251/g), but there for linkage purposes.
Real code to follow, once I get past some boot issues on my pc98 boxes
with recent current.
It improves on sio(4) in the following areas:
o Fully newbusified to allow for memory mapped I/O. This is a must
for ia64 and sparc64,
o Machine dependent code to take full advantage of machine and firm-
ware specific ways to define serial consoles and/or debug ports.
o Hardware abstraction layer to allow the driver to be used with
various UARTs, such as the well-known ns8250 family of UARTs, the
Siemens sab82532 or the Zilog Z8530. This is especially important
for pc98 and sparc64 where it's common to have different UARTs,
o The notion of system devices to unkludge low-level consoles and
remote gdb ports and provides the mechanics necessary to support
the keyboard on sparc64 (which is UART based).
o The notion of a kernel interface so that a UART can be tied to
something other than the well-known TTY interface. This is needed
on sparc64 to present the user with a device and ioctl handling
suitable for a keyboard, but also allows us to cleanly hide an
UART when used as a debug port.
Following is a list of features and bugs/flaws specific to the ns8250
family of UARTs as compared to their support in sio(4):
o The uart(4) driver determines the FIFO size and automaticly takes
advantages of larger FIFOs and/or additional features. Note that
since I don't have sufficient access to 16[679]5x UARTs, hardware
flow control has not been enabled. This is almost trivial to do,
provided one can test. The downside of this is that broken UARTs
are more likely to not work correctly with uart(4). The need for
tunables or knobs may be large enough to warrant their creation.
o The uart(4) driver does not share the same bumpy history as sio(4)
and will therefore not provide the necessary hooks, tweaks, quirks
or work-arounds to deal with once common hardware. To that extend,
uart(4) supports a subset of the UARTs that sio(4) supports. The
question before us is whether the subset is sufficient for current
hardware.
o There is no support for multiport UARTs in uart(4). The decision
behind this is that uart(4) deals with one EIA RS232-C interface.
Packaging of multiple interfaces in a single chip or on a single
expansion board is beyond the scope of uart(4) and is now mostly
left for puc(4) to deal with. Lack of hardware made it impossible
to actually implement such a dependency other than is present for
the dual channel SAB82532 and Z8350 SCCs.
The current list of missing features is:
o No configuration capabilities. A set of tunables and sysctls is
being worked out. There are likely not going to be any or much
compile-time knobs. Such configuration does not fit well with
current hardware.
o No support for the PPS API. This is partly dependent on the
ability to configure uart(4) and partly dependent on having
sufficient information to implement it properly.
As usual, the manpage is present but lacks the attention the
software has gotten.
o Introduce PUC_PORT_TYPE_UART so that we can attach to uart(4),
o Introduce port sub-types (eg PUC_PORT_UART_NS8250, PUC_PORT_UART_Z8530)
to handle different hardware and determine resource sizes.
o Introduce two new IVARs: PUC_IVAR_SUBTYPE and PUC_IVAR_REGSHFT. Both
are used by uart(4) to get sufficient information to talk to the HW.
o Introduce PUC_FLAGS_ALTRES to tell puc(4) to try memory mapped I/O
if I/O port space cannot be allocated, or vice versa.
o Have ports of type PUC_PORT_TYPE_COM attach to uart(1) if attaching
to sio(4) fails (due to not having the sio driver).
o Put struct puc_device_description in struct puc_softc instead of
having a pointer to a device description in the softc. This allows
us to create device descriptions on the fly without having to use
malloc() or otherwise have them staticly defined.
o Move puc_find_description() from puc.c to puc_pci.c as it's specific
to PCI.
o Add EBUS and SBUS frontends for use on sparc64. Note that the P in
puc stands for PCI, so we kinda mess things up here. It's too soon
to worry about it though. We'll know what to do about it in time.
NOTE: This commit changes the behaviour of puc(4) to not quieten the
device probe and attach for child devices. The uart(4) driver provides
additional device description that is valuable to have.
For the floppy driver, use fdcontrol to manipulate density selection.
For the CD drivers, the 'a' and 'c' suffix is without actual effect and
any applications insisting on it can be satisfied with a symlink:
ln -s /dev/cd0 /dev/cd0a
Ongoing discussion may result in these pieces of code being removed before
the 5-stable branch as opposed to after.
such a card is ejected, we'd panic. Instead, just ignore it.
I should also add a sanity check in the FUNCID code as well, but this
isn't wrong since the check is cheap and happens infrequently.
and replace it with the more intuitive name PCIR_BARS.
- Add a PCIR_BAR(x) macro that returns the config space register offset of
the 32-bit BAR x.
MFC after: 3 days
switched from PCCARD_MEM_FOO to PCCARD_A_MEM_FOO, yet we didn't change
exca in all the right places. Do so now. Also use PCCARD_WIDTH_AUTO
rather than the magic cookie 0.
change also disables interrupts around non-S4 suspends whereas before we
did not do this. Our version of AcpiEnterSleepStateS4bios was almost
identical to the ACPICA version.
- Add a new PCIM_HDRTYPE constant for the field in PCIR_HDRTYPE that holds
the header type.
- Replace several magic numbers with appropriate constants for the header
type register and a couple of PCI_FUNCMAX.
- Merge to amd64 the fix to the i386 bridge code to skip devices with
unknown header types.
Requested by: imp (1, 2)
reading the CIS on some cards. However, not all just yet. This makes
at least some of the xircom cards that weren't working to work. It
doesn't make my home and away card work, however.
o Don't get the card offset wrong. This is the biggest hassle for
reading the CIS. The old code was just so wrong I can't believe that
it worked at all.
o Don't set the bit that allows/forces 16-bit memory access to the
memory. It is hard coded with 0x80.
o Don't need to slow down memory access with wait-states. OLDCARD didn't
need them and it doesn't hurt anything.
o remove bogus grousying in comment.
Bug Fixes:
- Allow users to use LAA
- Remember promiscuous mode settings while bridging
- Allow gratuitous arp's to be sent
PR: 52966/54488
MFC after: 1 week
METEORSSIGNAL ioctl. Applications use this ioctl with the value
METEOR_SIG_MODE_MASK (0xFFFF0000, -65536) to reset signal delivery,
but revision 1.126 caused the driver to return EINVAL in this case.
Interestingly, the same METEORSSIGNAL ioctl in the meteor driver uses
0 to reset signal delivery.
This commit allows METEOR_SIG_MODE_MASK as a synonym for 0 in the
bktr driver, and restructures the code a bit so that it is otherwise
identical between the bktr and meteor drivers.
compatibility routine, go ahead and accept that as 'success'. A
properly written compatible driver should return < 0 for both the
compat match and compat probe routines, so this will wind up doing the
right thing.
This will get rid of the warnings issued at shutdown (that seems to
worry alot of users), but will also no flush cache on lots of
devices that can, but doesn't set the right support bits...
Restructure the way ATA/ATAPI commands are processed, use a common
ata_request structure for both. This centralises the way requests
are handled so locking is much easier to handle.
The driver is now layered much more cleanly to seperate the lowlevel
HW access so it can be tailored to specific controllers without touching
the upper layers. This is needed to support some of the newer
semi-intelligent ATA controllers showing up.
The top level drivers (disk, ATAPI devices) are more or less still
the same with just corrections to use the new interface.
Pull ATA out from under Gaint now that locking can be done in a sane way.
Add support for a the National Geode SC1100. Thanks to Soekris engineering
for sponsoring a Soekris 4801 to make this support.
Fixed alot of small bugs in the chipset code for various chips now
we are around in that corner anyways.
support stripped out and minimally renamed to owi. This driver
attaches to lucent cards only. This is designed to aid in the testing
of fixes to the wi driver for lucent cards. It is supported only as a
module (you cannot compile it into your kernel). You cannot have the
wi driver in your kernel (or loaded as a moudle) to use the owi
module.
I've not connected it to build, as this module is currently for
debugging purposes. This is for developers only at the present time.
If we can't get lucent support fixed by 5.2 code freeze, then we'll
re-evaulate this support level. Please use this to fix the lucent
support in dev/wi. This will be removed from the system when lucent
support has been fixed in dev/wi.
Note to developers: Do not connect this to the build, make it possible
to build into the kernel or otherwise 'integrate' this into system
without checking with me first. This is for debugging purposes only.
If this doesn't work for you, I don't want to hear about it unless you
are fixing the wi driver :-)
gfb_draw if 'flip' is specified. This causes the mouse cut region
to be displayed in reverse color so it is visbile.
- Use the "other" implementation of gfb_cursor for the creator driver,
which doesn't assume there is a hardware cursor. It seems that the
hardware cursor that creator provides doesn't display the character
under the cursor in reverse colors, so the driver does this manually
and uses the hardware cursor for the mouse pointer (which it also works
much better for). This is wedged here because it required less hoops
than accessing the syscons vtb from inside the video driver, which is
needed to read the character and color attributes under the new cursor
position.
These are fixed resolution and operate only in pixel mode so they present
a challenge to syscons (square peg, round hole, etc, etc). The driver
provides a video driver interface for syscons and a separate character
device for X to mmap. Wherever possible the creator's accelarated graphics
functions are used so text mode is very fast.
Based roughly on the openbsd driver.
round the result up to a multiple of 4 bytes so that it will always
be a multiple of the sample size. Also use the actual buffer size
from sc->bufsz instead of the default DS1_BUFFSIZE.
This fixes panics and bad distortion I have seen on Yamaha DS-1
hardware, mainly when playing certain Real Audio media.
Reviewed by: orion (an earlier version of the patch)
first sample in the buffer to be ignored. The bug caused a repetitive
glitch in one of the stereo channels when playing mono sound on
configurations that use the monotostereo16 feeder.
Reviewed by: orion
to intptr_t. This fixes a compiler warning (integer from pointer
without cast) in scvgarndr.c when SC_PIXEL_MODE is defined.
o Define readb() and writeb(). Both are used in scvgarndr.c when,
guess what, SC_PIXEL_MODE is defined.
Both changes are ia64 specific.
Found by: LINT
CB710, CB720, CB1211, CB1225, CB1410 and CB1420
These are likely licensed designed from TI, and the Linux PCMCIA code
treats them as TI chips.
Add comment, but no ID for the 711E1 from O2Micro.
vendors that list the vendor ID in the proper byte order. The second
section is for vendors that get it backwards. The third is for what
appear to be 'random' ones (although 0xcxxx appears to be coherent
enough that maybe somebody else is assigning those numbers).
o AD1980 hook.
o ac97_fix_auxout.
and:
o Associate AC97_MIX_AUXOUT with SOUND_MIXER_OGAIN rather than
SOUND_MIXER_MONITOR.
o Add ac97_fix_tone to remove tone controls from mixer if invalid.
are all bogus, and the cards that don't decode things quite right
often have hundreds of them. This will fix starvation of small dmesg
buffers and allow better debugging to happen. I thought about adding
an override, but there is such a thing as too many knobs. :-)
- Fix up TX speed changes.
- Make mpi-350 cards sort-of work with new firmware. It RXs okay but TXs
only work for about 14 packets then fails to get an interrupt. The
TX watchdog fires. It has been reported that my hack for now doesn't
break cards with the older firmware. It appears my card has lost
the ability to RX or TX at all but other peoples cards work. I assume
it got damaged in tansport.
MFC: 1 week.
count handling of station entries in hostap mode:
Input path:
o driver is now expected to find the node associated with the
sender of a received frame; use ic_bss if none is located
o driver passes the (referenced) node into ieee80211_input for
use within the wlan module and is responsible for cleaning up
on return
o the antenna state is no longer passed up with each frame; this
is now considered driver-private state and drivers are responsible
for keeping it in the driver-private part of a node
Output path:
Revamp output path for management frames to eliminate redundant
locking that causes problems and to correct reference counting
bogosity that occurs when stations are timed out due to inactivity
(in AP mode). On output the refcnt'd node is stashed in the pkthdr's
recvif field (yech) and retrieved by the driver. This eliminates
an unref/ref scenario and related node table unlock/lock due to the
driver looking up the node. This is particularly important when
stations are timed out as this causes a lock order reversal that
can result in a deadlock. As a byproduct we also reduce the overhead
for sending management frames (minimal). Additional fallout from
this is a change to ieee80211_encap to return a refcn't node for
tieing to the outbound frame. Node refcnts are not reclaimed until
after a frame is completely processed (e.g. in the tx interrupt
handler). This is especially important for timed out stations as
this deref will be the final one causing the node entry to be
reclaimed.
Additional semi-related changes:
o replace m_copym use with m_copypacket (optimization)
o add assert to verify ic_bss is never free'd during normal operation
o add comments explaining calling conventions by drivers for frames
going in each direction
o remove extraneous code that "cannot be executed" (e.g. because
pointers may never be null)
quietly discard them; this just permits them to be collected with bpf)
o add a counter for the number of rate control frames discarded when not in
monitor mode
o move the rx "too short" statistic in the stat structure so non-error rx stats
are together (NB: ABI change to apps that collect stats via driver ioctl)
mistakes (this mistake was not an issue because the length is only used to
decide whether or not to allocate a cluster)
o while here, move a beacon length comment to the "right place"
present, and non-zero when it is (or may be) absent. The test
cbb_child_present was backwards. However, typical usage in the tree
would cause it to do the right thing because the card really wasn't
there the OK flag would be turned on.
Also, assume that if any of these bits are turned on we don't have a
card, rather than requiring both of them in the suspend/resume
routines.
Noticed by: cognet
to what is in NetBSD. I have a few cards that tickles this bug, and
this just keeps us from panicing. It doesn't actually fix the problem
(that will happen once I figure out why some cards hate the address
their CIS is mapped to high memory).
A timecounter will be selected when registered if its quality is
not negative and no less than the current timecounters.
Add a sysctl to report all available timecounters and their qualities.
Give the dummy timecounter a solid negative quality of minus a million.
Give the i8254 zero and the ACPI 1000.
The TSC gets 800, unless APM or SMP forces it negative.
Other timecounters default to zero quality and thereby retain current
selection behaviour.
Correctly handle additional disks without BIOS partition tables.
Previously, vinum_scandisk stopped scanning additional disks for
native partitions after any good partition was found. This applies
to all platforms, but was a particular problem on systems without
BIOS partition tables.
Submitted by: harti
the hardware mutex if it is held. Re-add calls to Enable/Clear fixed events.
This is not known to have caused problems. Bug symptoms might have included
instability after an aborted suspend attempt or power/sleep buttons not
being enabled.
CP-168U board. It initializes and attaches in the same way as the
older (but higher performance) C168H. The only difference is the
board ID, which is 0x1681.
PR: kern/53548
Submitted by: regnauld@catpipe.net
MFC after: 1 week
the Palm device and the USB host controller deadlock. The USB host
controller is expecting an early-end-of-transmission packet with 0
data, and the Palm doesn't send one because it's already communicated
the amount of data it's going to send in a header (which ucom/uvisor
are oblivious to). This is the problem that has been known on the
pilot-link lists as the "[Free]BSD USB problem", but not understood.
Submitted by: Nathan J. Williams <nathanw@MIT.EDU>
for partly-aligned operations through /dev/crypto (unlikely)
o add missing case in iov code that never showed up because of the above bug
Submitted by: "Jason L. Wright" <jason@thought.net>
MFC after: 3 days
found only many tv-cards.
We currently use more ore less evil hacks (slow_msp_audio sysctl) to
configure the various variants of these chips in order to have
stereo autodetection work. Nevertheless, this doesn't always work
even though it _should_, according to the specs.
This is, for example, the case for some popular Hauppauge models sold
sold in Germany.
However, the Linux driver always worked for me and others. Looking at
the sourcecode you will find that the linux-driver uses a very much
enhanced approach to program the various msp34xx chipset variants,
which is also found in the specs for these chips.
This is a port of the Linux MSP34xx code, written by Gerd Knorr
<kraxel@bytesex.org>, who agreed to re-release his code under a
BSD license for this port.
A new config option "BKTR_NEW_MSP34XX_DRIVER" is added, which is required
to enable the new driver. Otherwise the old code is used.
The msp34xx.c file is diff-reduced to the linux-driver to make later
modifications easier, thus it doesn't follow style(9) in most cases.
Approved by: roger (committing this, no time to test/review),
keichii (code review)
These are 10/100 only NICs found on the IBM Thinkpad R40E and
G40. These seem to be based on the BCM5705 MAC but with a PHY
that doesn't support 1000Mbps modes.
Submitted by: Igor Sviridov <sia@nest.org>
ioctls.
In the particular case of ptrace(), this commit more-or-less reverts
revision 1.53 of sys_process.c, which appears to have been erroneous.
Reviewed by: iedowse, jhb
to configure this correctly yields many watchdog timeouts even on lightly
loaded machines. This is a common complaint from users with Dell 1750
servers with built-in dual 5704 NICs.
the time the card is inserted and the time that the card is
configured. This can lead to interrupt storms. The O2Micro suggested
workaround is to route the card function interrupt to IRQ1. It
appears from my testing that this is an acceptable workaround for most
chipsets (there's still some issue with the ricoh chipset).
Also, only look at the NOT_A_CARD bit when the bridge tells us there's
a card present. At least one test caused this to be true after the
card was removed, but the author couldn't recreate it with the
workaround in place. The change is more conservative than the
previous code, but still has the work around that wasn't present in
the older code.
BGE_MACSTAT_MI_COMPLETE bit in the MAC status register as a link
change indicator. We turn this bit on now because some of the newer
chips need it, but it usually just means that reading/writing
an MII/GMII register has completed, not that a link change has
occured.
the standard.
1) When the bridge tells us that we have a card that isn't recognized, we
use the force register to force the CV_TEST to run. This test causes the
bridge to re-evaluate the card. Once this re-evaluation process happens,
we get a new interrupt that may say it is ready to process. We try this up
to 20 times. Tests have shown that this appears to correctly reset the
'Unknown card type' problem that I saw on my Sony PCG-505TS.
2) Take a page from OLDCARD and always read the CSC register in the ISR.
Some TI (and it seems maybe Ricoh) chipsets require this to behave
properly. This work around appears to work due to some power management
protocols that were improperly implemented. Maybe it can be removed when
this driver supports the full PME# protocol described in the standards.
3) Minor additional debug printf when debugging is enabled.
4) Minor additional commentary for things that are obvious only after study.
# I'm committing this from my Sony PCG-505TS using shared PCI interrupts
# and NEWCARD, but there are some issues with the Ricoh bridge still, but
# at least now I can boot with the card inserted and have it work.
PCG-505BX (for example) has one of those:
wi0: <Intersil Prism3> mem 0xf8000000-0xf8000fff at device 2.0 on pci2
wi0: 802.11 address: 00:02:8a:94:d8:73
wi0: using RF:PRISM3(Mini-PCI)
wi0: Intersil Firmware: Primary (1.1.1), Station (1.5.6)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
has the same product id, but different vendor id. It also appears
that the MELCO's id should be 0x18a instead of 0x8a01. Fix this.
Submitted by: Shizuka Kudo-san
and up commands. When configuring the interface down only the
connections that are currently closing are deleted from the connection
table. When the interface is configured up, all connections that
are in the table are re-opened.
connections that have been open (and were not closing) when
the interface was stopped. This makes the behaviour of fatm(4) more like
the behaviour of en(4).
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
- Build SGL's for ATA_PASSTHROUGH commands
- Fallback to using the sgl_offset when the opcode is unknown for building
SGL's/
- Add ioctl calls for adding and removing units.
- Define previously undefined AEN's
- Allocate memory for the ioctl payload in multiples of 512bytes.
MFC after: 1 week
preparation for supporting the OPENVCC and CLOSEVCC ioctls which
are needed for ng_atm. This required some re-organisation of the code
(mostly converting array indexes to pointers). This also gives us
an array of open vccs that will help in using the generic GETVCCS handler.
the macro definition, and cause the generation of syntactically
incorrect code that gcc happens to accept.
Reviewed by: schweikh (mentor)
MFC after: 4 weeks
larger than normal frames, to account for the case where a bge(4) NIC
is used with VLANs. Since we set the IFCAP_VLAN_MTU flag, we must allow
reception of frames up to 1522 bytes in size rather than 1518.
Note that it is possible to work around this bug by doing:
# ifconfig bge0 mtu 1504
prior to configuring any VLAN interfaces.
recompiling the driver. See the comments near the top of "if_em.h"
for descriptions of these delays. Four new loader tunables control
the system-wide default values:
hw.em.tx_int_delay
hw.em.rx_int_delay
hw.em.tx_abs_int_delay
hw.em.rx_abs_int_delay
The tunables are specified in microseconds. The valid range is
0-67108 usec., and 0 means that the timer is disabled.
There are also four new sysctls (actually, a set of four for each
"em" device in the system) to query and change the interrupt delays
after the system is up:
hw.em0.tx_int_delay
hw.em0.rx_int_delay
hw.em0.tx_abs_int_delay (not present for 82542/3/4 adapters)
hw.em0.rx_abs_int_delay (not present for 82542/3/4 adapters)
It seems to be OK to change these values even while the adapter is
passing traffic.
Approved by: Prafulla Deuskar <pdeuskar@FreeBSD.ORG>
MFC after: 4 weeks
- Move isa/ppc* to sys/dev/ppc (repo-copy)
- Add an attachment method to ppc for puc
- In puc we need to walk the chain of parents.
Still to do, is to make ppc(4) & puc(4) work on other platforms. Testers
wanted.
PR: 38372 (in spirit done differently)
Verified by: Make universe (if I messed up a platform please fix)
This is controlled by a per-adapter sysctl hw.atm.hfaX.shape. When
set to 0, no shaping occures. When set to 1 at most 1 channel is
shaped. When set to 2 all CBR channels are shaped. Note, that the
latter may actually not work, because of the adapter supporting
the shaping of only one PDU at the same time.
also do it). Three problems have been encountered:
1. The initialisation command does not work in interrupt mode. Whether
this is a firmware bug or a feature is not clear. The original Fore
drivers execute the initialize command always in polling mode, so
it appears that this behaviour is expected. When we detect a 4.X.Y
firmware do busy wait on the command status.
2. The command code of the GET_PROM command has changed. This is an
unofficial command anyway. What was GET_PROM in 3.X.Y is CLEAR_STATS
in 4.X.Y (although unimplemented in the firmware). We need to
use the correct code depending on the firmware.
3. The 4.X.Y firmware can set the error flag in the command status
without also setting the completion flag (as the documenation says).
Check both variants.
An additional field in the per-card structure fu_ft4 is TRUE when we have
detected a 4.X.Y firmware. Otherwise it is false. The behaviour of the
driver when using a 3.X.Y firmware should be identical to the previous
behaviour.
This change will enable traffic shaping of (at least one) CBR channels.
allocation function. With this patch, it prevents continous growth of
the devbuf memory pool.
Tested with ssh <host> dd of=/dev/null < /dev/zero and vmstat -m | grep devbuf
receive 6 byte commands. Add a check for this flag to da(4) and cd(4) so
that they honor it. This is a quick workaround for many devices (especially
USB) that require da(4) quirks to operate. The more complete approach is
to finish the new transport code which will be aware of the SCSI version a
transport implements.
MFC after: 1 day
function unless the device is configured up. Without this fix, the
device ends up in the RUNNING state even though it is configured down.
Also, check the RUNNING flag before calling the if_start function, in
case the if_init function failed for one reason or another.
contain the filedescriptor number on opens from userland.
The index is used rather than a "struct file *" since it conveys a bit
more information, which may be useful to in particular fdescfs and /dev/fd/*
For now pass -1 all over the place.
newer lucent/hermes firmware than indicated (investigating). I'm committing
this now since it shouldn't hurt anything.
o Vaguely related, add bogus frame length check from netbsd.
Obtained from: netbsd
it attaches to all existing NATM network interfaces in the system
and creates a HARP physical interface for each of them. This allows
us to use the same set of ATM drivers for all ATM stuff. It is
possible to use the same interface for HARP, NATM and netgraph at the
same time.
go looking for free fragments won't match. Since we never free this, we
can "throw away" the tag. This is very dirty, and needs to be reimplemented
properly, but fixes performance problems with uhci.
Also assert that when we overlay a structure on some space, that the
space is large enough for the structure.
namespace. To compensate for it only being used in the !ECDT case, use
a more robust approach to indicate a device was probed via ECDT by setting
the private ivar to be &acpi_ec_devclass. Without the acpi_MatchHid() call
now, it might have been possible for a non-EC device to have had its magic
match our previous flag.
Pointed out by: takawata
to EcGpeQueryHandler on to any waiting threads through the softc. Similar
behavior was in the original version.
Also:
* Merge EcQuery into EcGpeQueryHandler to simplify locking
* Hold EcLock from the initial read of the CSR down to the wakeup or
until after the query command has been processed.
* ec_gpebit only needs to be a UINT8
namespace has been evaluated. Machines with ACPI 2.0 expect this behavior
and have AML which calls EC functions early in the boot process. If the
ECDT is not available, fall back to original probe behavior.
Other minor changes:
* Add GPE bit and GLK usage to the device announcement
* Always use the global lock in the ECDT case, but potentially downgrade to
not using it if _GLK is 0 once the namespace is available. This is
announced with "Changing GLK from 1 to 0"
* Remove the acpi_object_list definitions which were earlier deprecated
Ideas from: takawata
