if_cuereg.h (1.5), if_kue.c (1.11), if_kuereg.h (1.5)
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
We don't have ratecheck() in our kernel yet, so I've hardcoded
usb_ratecheck() to return true always.
usbdi.c (1.86), usbdivar.h (1.66)
[Some partial, because most of this was merged in a while ago]
date: 2001/11/20 13:48:03; author: augustss;
Keep track of device speed for USB 2.0.
revision 1.106
date: 2001/11/09 15:01:57; author: augustss; state: Exp; lines: +73 -57
Fix a bug in xfer abort processing when the HC executes ahead of what
the driver aborts.
Don't block RHSC interrupts.
revision 1.103
date: 2001/09/11 07:00:19; author: augustss; state: Exp; lines: +4 -1
Don't go top mode OPERATIONAL (before reset) on startup even
if BIOS claims to have initialized the controller.
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
date: 2001/08/15 00:04:59; author: augustss;
Add a little infrastructure so that individual drivers can easily check
if thee was a vendor+product locator match.
revision 1.50
date: 2001/04/12 01:18:24; author: thorpej; state: Exp; lines: +6 -2
Only if __HAVE_GENERIC_SOFT_INTERRUPTS is then splusb == splsoftnet
(because we register the interrupt with IPL_SOFTNET). However, if
we're using a callout, then splusb == splsoftclock (because the
callouts happen from the softclock interrupt).
Note that splsoftnet blocks softclock interrupts, but this is
meant to better describe what's going on.
date: 2001/01/21 19:00:06; author: augustss;
Change the operation of the USB event thread. Before it only
performed USB device discovery, now it can also perform (short)
tasks for device drivers that need a process context, but don't
have one. This is not pretty, but better than using busy-wait
in an interrupt context.
revision 1.138
date: 2001/10/02 17:59:38; author: pooka; state: Exp; lines: +6 -6
move DIAGNOSTIC-printf up one block to make it reachable
noted by Christophe Kalt in private email
(1.39), usbdi.c (1.79), usbdi.h (1.47), usbdivar.h (1.62)
date: 2001/01/21 02:39:52; author: augustss;
Add code to use soft interrupt to handle USB interrupt processing.
Don't enable the code since it doesn't work with the kludgy Ethernet
drivers.
general cleanup of the API. The entire API now consists of two functions
similar to the pre-KSE API. The suser() function takes a thread pointer
as its only argument. The td_ucred member of this thread must be valid
so the only valid thread pointers are curthread and a few kernel threads
such as thread0. The suser_cred() function takes a pointer to a struct
ucred as its first argument and an integer flag as its second argument.
The flag is currently only used for the PRISON_ROOT flag.
Discussed on: smp@
revision 1.58
date: 2000/06/24 04:12:53; author: thorpej; state: Exp; lines: +5 -2
Kill SPLUSBCHECK -- it's not portable, and quite annoying on some
platforms which otherwise function just fine.
revision 1.127
date: 2000/11/22 05:50:59; author: soren; state: Exp; lines: +5 -5
In uhci_intr(), only warn about power state confusion if the
interrupt was actually for us.
date: 2000/08/08 19:51:46; author: tv; state: Exp; lines: +24 -13
%b -> bitmask_snprintf()
Because this code is shared, add a macro for bitmask_snprintf()
that should expand to the equivalent snprintf() on non-NetBSD
systems. This is only used in ?HCI_DEBUG cases anyway.
revision 1.81
date: 2000/10/24 15:01:26; author: augustss; lines: +36 -10
Add a hack to try and figure out if the TI UTUSB41 hub is bus
powered despite claiming to be self powered (it's important to
know so that the power budget can be met).
Part of this got merged in a previous commit, but not all.
revision 1.72
date: 2000/04/14 14:13:56; author: augustss; state: Exp; lines: +34 -27
Make attach of ugen work as it should so product&vendor locators
can be used.
usb.c 1.40:
revision 1.40
date: 2000/03/14 23:13:12; author: augustss; state: Exp; lines: +4 -1
Make sure the USB event thread discovers all devices first time
it call usb_discover(). It should now be possible to have the
root NFS mounted over a USB Ethernet Adapter.
----------------------------
revision 1.73
date: 2000/05/31 16:14:42; author: augustss; state: Exp; lines: +19 -6
Be more careful when setting the alternate interface so we don't
end up with nothing set at all if it fails.
----------------------------
----------------------------
revision 1.117
date: 2000/05/30 09:26:06; author: augustss; lines: +7 -1
As a safety, check that the controller is not suspended when we get
an interrupt.
----------------------------
ohci.c (1.85), ohcireg.h (1.17):
----------------------------
date: 2000/04/01 09:27:35; author: augustss;
Add a delay before reading the number of ports from the controller to
avoid getting 0 from it.
----------------------------
ohci.c (1.83), ohcireg.h (1.16), ohcivar.h (1.21)
===================================================================
date: 2000/03/29 01:46:26; author: augustss;
A first stab at support for isochronous transfers.
===================================================================
ohcivar.h (1.22), uhcivar.h (1.29):
============================================================
date: 2000/04/25 09:20:55; author: augustss;
Move the size of the mapped bus_space region into the bus
independent softc.
============================================================
ohci.c (1.88), uhci.c (1.112):
============================================================
date: 2000/04/25 14:28:13; author: augustss;
Insert (very conservative!) bus_space_barrier() calls at
all register accesses.
The bus_space(9) man page says you've gotta have them...
============================================================
usbdi.c (1.61):
===================================================================
revision 1.61
date: 2000/01/31 20:13:07; author: augustss; lines: +20 -4
Change the way the HC done method is invoked a little.
===================================================================
usbdi.c (1.65):
===================================================================
revision 1.65
date: 2000/03/08 15:34:10; author: augustss; lines: +4 -2
Get the status right when a polled transfer times out.
===================================================================
ohci.c (1.79), uhci.c (1.89), uhcivar.h (1.24), usb_port.h (1.22),
usbdivar.h (1.48):
===================================================================
date: 2000/03/23 07:01:46; author: thorpej;
New callout mechanism with two major improvements over the old
timeout()/untimeout() API:
- Clients supply callout handle storage, thus eliminating problems of
resource allocation.
- Insertion and removal of callouts is constant time, important as
this facility is used quite a lot in the kernel.
The old timeout()/untimeout() API has been removed from the kernel.
===================================================================
uhci.c (1.80), usbdi.c (1.66):
===================================================================
date: 2000/03/23 18:59:10; author: thorpej;
Shake out some bugs from the callout changes.
===================================================================
ohci.c (1.80), uhci.c (1.91), uhcivar.h (1.25), usb_port.h (1.23),
usbdi.c (1.67), usbdivar.h (1.49):
===================================================================
date: 2000/03/24 22:03:30; author: augustss;
Some cleanup and renaming of the callouts used in USB drivers.
===================================================================
uhci.c (1.92), uhcivar.h (1.26):
===================================================================
date: 2000/03/24 22:57:58; author: augustss;
Two major changes:
Make each xfer have its own intr_info. This is necessary if we want
to queue multiple xfers on an endpoint. This should get rid of the
(mostly harmless) DIAGNOSTICs about intr_infos (not) being done.
Change (again!) how xfers are aborted. Aborting a TD is a nightmare
on the braindead UHCI controller. (Unless you stop the HC, thereby
losing isoc traffic.) Hopefully I got it right this time.
===================================================================
usbdivar.h (1.50):
===================================================================
revision 1.50
date: 2000/03/25 00:10:19; author: augustss; lines: +4 -2
GC an unsued field and add some DIAGNOSTIC in xfer.
===================================================================
ums.c: Use the callout functions instead of the timeout ones.
uhci.c (1.93):
===================================================================
revision 1.93
date: 2000/03/25 00:11:21; author: augustss;
lines: +26 -1
Add more DIAGNOSTIC when aborting isoc.
===================================================================
uhci.c (1.94), usbdivar.h (1.51):
===================================================================
date: 2000/03/25 07:13:05; author: augustss;
More DIAGNOSTIC.
Initialize a callout handle I forgot.
===================================================================
uhci.c (1.95):
===================================================================
revision 1.95
date: 2000/03/25 07:23:12; author: augustss;
Exp; lines: +24 -7
Improve uhci_dump_ii().
===================================================================
ohci.c (1.81), uhci.c (1.96), uhcivar.h (1.27), usb_subr.c (1.68),
usbdi.c (1.68), usbdivar.h (1.52):
===================================================================
date: 2000/03/25 18:02:33; author: augustss;
Rename and move around callout handles to make it more sane.
Add some DIAGNOSTIC.
Fix buglet in isoc abort on UHCI.
===================================================================
uhci.c (1.98):
===================================================================
revision 1.98
date: 2000/03/27 07:39:48; author: augustss; lines: +12 -4
Make it compile without DIAGNOSTIC.
===================================================================
uhci.c (1.99):
===================================================================
revision 1.99
date: 2000/03/27 08:01:09; author: augustss; lines: +1 -5
Remove some debug nonsense.
===================================================================
uhci.c (1.100):
===================================================================
revision 1.100
date: 2000/03/27 09:41:36; author: augustss; lines: +13 -3
Don't mess with QH in bulk abort for the moment.
===================================================================
uhci.c (1.102):
===================================================================
revision 1.102
date: 2000/03/27 22:42:57; author: augustss; lines: +66 -26
Be a little more careful when aborting.
Preallocate some TDs for large buffers.
===================================================================
uhci.c (1.103):
===================================================================
date: 2000/03/28 09:47:10; author: augustss; lines: +11 -1
Another patch for xfer abort...
XXX The current xfer queueing and aborting semantics should really
XXX be changed. It cannot be implemented in a sane way on UHCI.
XXX One day when I have lots of time I'll redesign it...
===================================================================
uhci.c (1.104): Correct a debug message.
uhci.c (1.105): Be more defensive in a DIAGNOSTIC test.
uhci.c (1.106):
===================================================================
revision 1.106
date: 2000/03/29 01:49:13; author: augustss; lines: +14 -309
*SIGH* Revert back to the old method of aborting xfers.
I had tested the new stuff for two months now, but as soon as I commited
it the problems started to appear. Murphy, no doubt...
===================================================================
usb_subr.c (1.70), usbdi.c (1.71), usbdivar.h (1.53):
===================================================================
revision 1.70
date: 2000/03/29 01:45:20; author: augustss; lines: +2 -1
Do not accept new xfers for queuing while a pipe is aborting.
===================================================================
Problem:
selwakeup required calling pfind which would cause lock order
reversals with the allproc_lock and the per-process filedesc lock.
Solution:
Instead of recording the pid of the select()'ing process into the
selinfo structure, actually record a pointer to the thread. To
avoid dereferencing a bad address all the selinfo structures that
are in use by a thread are kept in a list hung off the thread
(protected by sellock). When a selwakeup occurs the selinfo is
removed from that threads list, it is also removed on the way out
of select or poll where the thread will traverse its list removing
all the selinfos from its own list.
Problem:
Previously the PROC_LOCK was used to provide the mutual exclusion
needed to ensure proper locking, this couldn't work because there
was a single condvar used for select and poll and condvars can
only be used with a single mutex.
Solution:
Introduce a global mutex 'sellock' which is used to provide mutual
exclusion when recording events to wait on as well as performing
notification when an event occurs.
Interesting note:
schedlock is required to manipulate the per-thread TDF_SELECT
flag, however if given its own field it would not need schedlock,
also because TDF_SELECT is only manipulated under sellock one
doesn't actually use schedlock for syncronization, only to protect
against corruption.
Proc locks are no longer used in select/poll.
Portions contributed by: davidc
-#if defined(__FreeBSD__) && __FreeBSD_version__ >= 500023
+#if defined(__FreeBSD__) && __FreeBSD_version >= 500023
is a genuine bug -- __FreeBSD_version__ does not exist.
The other one:
-#if (__FreeBSD__ < 5)
+#if (__FreeBSD_version < 500000)
pops out when you cross-compile the code:
__FreeBSD__ is a compiler predefine,
__FreeBSD_version is defined in <sys/param.h> .
Given that in this case (and all others in sys/dev/usb and sys/i4b)
the goal is to adapt to a different kernel interface, and not to
a compiler feature, I believe the correct form is the second one
(in the best case the two are synonyms so the change does not break
anything anyways).
device drivers for bus system with other endinesses than the CPU (using
interfaces compatible to NetBSD):
- bwap16() and bswap32(). These have optimized implementations on some
architectures; for those that don't, there exist generic implementations.
- macros to convert from a certain byte order to host byte order and vice
versa, using a naming scheme like le16toh(), htole16().
These are implemented using the bswap functions.
- stream bus space access functions, which do not perform a byte order
conversion (while the normal access functions would if the bus endianess
differs from the CPU endianess).
htons(), htonl(), ntohs() and ntohl() are implemented using the new
functions above for kernel usage. None of the above interfaces is currently
exported to user land.
Make use of the new functions in a few places where local implementations
of the same functionality existed.
Reviewed by: mike, bde
Tested on alpha by: mike
1/ conditionalise (#if 0) function that is not used.
Unused code left in place for netBSD compatibility.
2/ Recode loop to convince gcc that it does initialise a variable
(use do-while instead of for() so gcc knows that we always go through
at least once. Feel free to check my logic.
Also, add some 'const's to supress warnings. (Submitted back to NetBSD).
The original logs from NetBSD:
----------------------------
revision 1.90
date: 2001/12/03 01:47:12; author: augustss; lines: +4 -4
Handle vendor/product lookup with a common routine.
----------------------------
revision 1.89
date: 2001/12/02 23:25:25; author: augustss; lines: +18 -2
Add a subroutine to search for a vendor/product pair.
----------------------------
Original NetBSD log messages are:
----------------------------
revision 1.23
date: 2001/12/12 15:48:18; author: augustss; lines: +132 -114
Add a scanner quirk for keeping the pipes open between device opening.
Idea from Enami.
----------------------------
revision 1.22
date: 2001/12/03 01:47:13; author: augustss; lines: +8 -16
Handle vendor/product lookup with a common routine.
----------------------------
revision 1.21
date: 2001/12/01 09:42:39; author: enami; lines: +4 -4
Shorten wmesg so that they can be distinguished in ps/top output.
----------------------------
revision 1.12
date: 2001/01/23 14:04:14; author: augustss; lines: +7 -1
Make sure driver attach/detach events are generated in a
consistent manner.
----------------------------
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
From the NetBSD logs:
revision 1.45
date: 2001/11/29 11:07:12; author: augustss; state: Exp; lines: +12 -2
Plug a memory leak in an error case.
----------------------------
revision 1.43
date: 2001/10/19 15:30:25; author: nathanw; state: Exp; lines: +5 -3
Match printers that report their interface as IEEE 1284 in addition to
bidirectional.
to fix their code.
ata stuff:
Change name of ar_attach to not colide with existing ar_attach in if_ar.c.
usb stuff:
Create a dummy function to satisfy a call to it when in DEBUG mode.
uhub.c: revision 1.37
usb.4: revision 1.30
usb.c: revision 1.38
usb.h: revision 1.40
usb_port.h: revision 1.21
usb_subr.c: revision 1.65
usbdi.h: revision 1.40
Split the attach/detach events up into device, driver and controller
attach and detach events.
The commit message from NetBSD was:
date: 2000/02/02 07:34:00; author: augustss; state: Exp;
Change the USB event mechanism to include more information
about devices and drivers. Partly from FreeBSD.
Also rework usbd to take these new event types into account.
usb.c: revision 1.39
revision 1.39
date: 2000/02/22 11:30:56; author: augustss; lines: +7 -1
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
usb.c: revision 1.41
revision 1.41
date: 2000/03/16 00:46:38; author: augustss; lines: +2 -2
Make the USB event queue longer. Mine overflows before the
(user-land) event handler has started. But then I have
about 25 devices connected. :)
ohci.c: revision 1.72 and 1.73
ohcivar.h: revision 1.19 and 1.20
uhci.c: revision 1.85
usbdi.h: a small part of revision 1.40
usbdivar.h: revision 1.47
Relevant commit messages from NetBSD are:
date: 2000/02/22 11:30:54; author: augustss; state: Exp;
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
----------------------------
date: 2000/02/01 05:42:53; author: augustss; state: Exp;
Put some #ifdefs around power and shutdown hooks.
usb.c: -r1.35 - 1.37
usb_port.h: tiny bit of -r1.26 + an extra bit in the FreeBSD config section.
revision 1.37
date: 2000/01/24 18:35:51; author: thorpej; state: Exp; lines: +7 -1
Use config_pending.
----------------------------
revision 1.36
date: 1999/12/22 23:54:09; author: augustss; state: Exp; lines: +2 -2
Use the flags `locator' to govern if devices are detected early or
late during cold boot.
----------------------------
revision 1.35
date: 1999/12/20 02:12:23; author: augustss; state: Exp; lines: +8 -5
Make sure tsleep() is not called during cold boot.
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
ohci.c: -r1.69 to 1.71
ohcireg.h: -r1.14
Some of these deltas are based upon patches that we submitted back to
NetBSD. They got manifested slightly differently though, so I've brought
back those differences to bring our code bases closer together.
The logs from the NetBSD version of ohci.c:
revision 1.71
date: 2000/02/01 05:42:52; author: augustss; state: Exp; lines: +13 -2
Put some #ifdefs around power and shutdown hooks.
----------------------------
revision 1.70
date: 2000/01/31 22:35:13; author: augustss; state: Exp; lines: +7 -7
Rename TAILMASK to HEADMASK, since it really masks the head pointer.
From FreeBSD.
----------------------------
revision 1.69
date: 2000/01/31 22:09:13; author: augustss; state: Exp; lines: +18 -14
Change where the has table for physical-to-virtual address translation
is handled. Partly from FreeBSD.
ohci.c: -r1.68
ohcireg.h: -r1.13
date: 2000/01/31 20:17:25; author: augustss; state: Exp;
Fiddle with over-current protect when turning on port power to make
things work for some OHCI controllers.
uhci.c: -r1.82
uhcivar.h: -r1.22
date: 2000/01/26 10:04:39; author: augustss; state: Exp;
Try to avoid accessing the HC if it is dead. Suggested by mycroft.
revision 1.125
date: 2000/09/23 21:00:10; author: augustss; state: Exp; lines: +19 -3
Avoid "bandwidth reclamation" for control transfers. The kue device chokes
on it.
uhci.c: -r1.124
uhcireg.h: -r1.13
date: 2000/08/13 18:20:14; author: augustss; state: Exp;
Fix race condition when unlinking xfers. Thanks to IWAMOTO Toshihiro
<iwamoto@sat.t.u-tokyo.ac.jp> for analyzing the problem and suggesting a fix.
Fixes PR 10662.
uhci.c: -r1.123 (and a tiny bit of -r1.92)
uhcivar.h: -r1.32
date: 2000/08/13 16:18:09; author: augustss; state: Exp;
Implement what in Intel-speech is known as "bandwidth
reclamation". It means that we continously poll USB devices
that have a pending transfer instead of polling just once
every ms. This speeds up some transfers at the expense of
using more PCI bandwidth.
uchireg.h: -r1.12
uchi.c: -r1.121
date: 2000/07/23 19:43:38; author: augustss; state: Exp;
Be a little more explicit and careful about setting links in TDs and QHs.
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
In order of importance:
* Make ugen use updated frlengths.
* More tests for NULL pipes.
* Generate better error codes on bulk write.
* Error messages in general.
sense, and mode select into their 10 byte equivalents. Eventually the
da(4) driver will become more intelligent about this, or at least allow
umass(4) to pass quirks in directly. However, this is a functional
workaround until a better fix is implemented.
- Use the 6 to 10 conversion function to allow the ATAPI and UFI command
sets to emulate 6 byte commands with 10 byte commands.
- Use the ATAPI command set rather than UFI for the ScanLogic SL11R-IDE
as it supports the SYNCH_CACHE command.
- Enable ATAPI command set support.
- Pass READ/WRITE_12 commands through for UFI support as the UFI spec
says they should be supported.
- Update a comment in the UFI translation function since we handle
MODE_SELECT.
the UFI command set. Even with this patch, it's incredibly slow on my
laptop, but at least now it works.
Note that the drive is reported to CAM with the vendor and device IDs from
the device itself, forcing the user to patch the da(4) quirk table
manually.
signature, but otherwise behaves just like a normal USB mass-storage
device. Add a new quirk to cover this case, and enable it for C-1
cameras. The quirk enables translation from the C-1 signature to
the normal CSWSIGNATURE value.
Reviewed by: n_hibma
Actually this porting supports Pegasus II chip so I guess some other
devices supported by NetBSD also work. But the devices list are not
included because I cannot confirm if they work.
Obtained from: NetBSD
MFC after: 3 weeks
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
events. Otherwise you would see unexpected results if shift or
locking keys are defined to give different actions depending
on other shift/locking keys' state.
Please keep the ukbd module and the kernel in sync, otherwise
the USB keyboard won't work after this change.
MFC after: 10 days
that device add/remove will work without usbd running. usbd is still
used for execing stuff, but that is all now. Ideally it could be replaced
by a devd some day. Until now, usbd had to be running so that the
USB_DISCOVER ioctl could be called to walk the tree when an attachment
status change was noticed.
Among the changes:
- when a detach happens, remove any pending 'attach' messages or the system
suffers from whiplash from exec moused / kill moused loops if you do lots
of attach/detach and later start usbd.
- tweaks related to kthread differences
- disable the select handler for the old interface (never return success).
I have not removed it yet or old usbd's will abort. That can get removed
later once usbd is cleaned up and things have stabilized for a few weeks.
- get Giant in the kthread.
- a couple of minor potential bug fixes (usb_nevents vs malloc failure etc)
Pre-approved by: n_hibma (ages and ages ago)
other "system" header files.
Also help the deprecation of lockmgr.h by making it a sub-include of
sys/lock.h and removing sys/lockmgr.h form kernel .c files.
Sort sys/*.h includes where possible in affected files.
OK'ed by: bde (with reservations)
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
interrupt threads to run with it always >= 1, so that malloc can
detect M_WAITOK from "interrupt" context. This is also necessary
in order to context switch from sched_ithd() directly.
Reviewed By: peter
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
Add the entry for the Yano U640MO-03 MO drive. (ifdef-0-ed out for now)
Fix a hack were an original buffer was modified instead of copied
(cmd[] -> (*rcmd)[])
Submitted by: Iwasa Kazmi <kzmi@ca2.so-net.ne.jp>
instead of the requested length. Otherwise all transfers look like 0 byte
transfers to CAM.
Submitted by: Iwasa Kazmi <kzmi@ca2.so-net.ne.jp>
2) Finalise the command in the case of CBI transfers with CCI (command
completion interrupt).
3) Remove a redundant bzero of a buffer.
This version is functional and is aproaching solid..
notice I said APROACHING. There are many node types I cannot test
I have tested: echo hole ppp socket vjc iface tee bpf async tty
The rest compile and "Look" right. More changes to follow.
DEBUGGING is enabled in this code to help if people have problems.
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
This clears out my outstanding netgraph changes.
There is a netgraph change of design in the offing and this is to some
extent a superset of soem of the new functionality and some of the old
functionality that may be removed.
This code works as before, but allows some new features that I want to
work with and evaluate. It is the basis for a version of netgraph
with integral locking for SMP use.
This is running on my test machine with no new problems :-)
USB WebCams, using a patch from Peter Housel.
With this change ugen, and with Peter's 'vid' program
in ports/graphics/vid, we can capture single images from USB Cameras
using the OmniVision OV511 chipset (including some models of the
Creative WebCam 3)
NetBSD merged in Peter's patch to their ugen.c file
several months ago, so this brings us back in line.
Submitted by: Peter Housel <housel@acm.org>
http://members.home.com/housel/
Approved by: Nick Hibma
Change a few indentations to tabs.
Change the functions to use ANSI sytle parameters.
This lowers the diffs between our copy of ugen.c and NetBSD's copy
Approved by: Nick Hibma
on. So stop failing the attach if the IRQ is unassigned. With this
patch, I can now boot with PNP-OS YES in my BIOS no differently than
PNP-OS NO (which is a good thing since Windows hangs with PNP-OS NO).
Obtained from: msmith
before adding/removing packets from the queue. Also, the if_obytes and
if_omcasts fields should only be manipulated under protection of the mutex.
IF_ENQUEUE, IF_PREPEND, and IF_DEQUEUE perform all necessary locking on
the queue. An IF_LOCK macro is provided, as well as the old (mutex-less)
versions of the macros in the form _IF_ENQUEUE, _IF_QFULL, for code which
needs them, but their use is discouraged.
Two new macros are introduced: IF_DRAIN() to drain a queue, and IF_HANDOFF,
which takes care of locking/enqueue, and also statistics updating/start
if necessary.
When the printer is turned off the pipe write will cause and error,
which causes lpd to close the device and reopen it to clear the error.
After a short while the device will disappear from the bus but lpd will
have opened the ulpt0 port by then. ulpt_status will check for status
without checking the sc->dying flag and panic the kernel when the device
finally disappears from the bus.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
multicast filter on the Pegasus chip. Since IPv6 depends a lot
on multicasting, this caused several failures for people trying to
use IPv6 with Pegasus USB ethernet devices.
Submitted by: Jun Kuriyama <kuriyama@FreeBSD.org>
<sys/proc.h> to <sys/systm.h>.
Correctly document the #includes needed in the manpage.
Add one now needed #include of <sys/systm.h>.
Remove the consequent 48 unused #includes of <sys/proc.h>.
the offending inline function (BUF_KERNPROC) on it being #included
already.
I'm not sure BUF_KERNPROC() is even the right thing to do or in the
right place or implemented the right way (inline vs normal function).
Remove consequently unneeded #includes of <sys/proc.h>
usb_ethersubr.c. This module maintains two queues for packets which
are each protected with one mutex. These are all the changes I can
do for now. Removing the USBD_NO_TSLEEP flag doesn't work yet: when
I tried it, the system would usually freeze up after a NIC had been
operating for a while. The usb_ethersubr module itself ought to
go away; this is the next thing I need to test.
length of the data properly. This should be moved into a tty_subr
function.
Also, disanle the setting of the CDC_CM_OVER_DATA flag. It breaks some
modems. I don't think that ther actually is a modem that needs this.
Submitted by: Brad Karp <bkarp@ICSI.Berkeley.EDU>
Replace all in-tree uses with <sys/mouse.h> which repo-copied a few
moments ago from src/sys/i386/include/mouse.h by peter.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/mouse.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/mouse.h> files will be removed.
Replace all in-tree uses with necessary subset of <sys/{fb,kb,cons}io.h>.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/console.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/console.h> files will be removed.
attached by the pnaphy driver. This seems to work fine with my sample
ADMtek adapter (which has both 10/100 ethernet and homePNA connectors
and hardware).
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
Make it possible to move a device to its unconfigured state by
using config #0.
Add some comments.
Change error reporting in port reset function.
usbd_devinfo_vp(): search the know devs array also if the device doesn't
return product description (e.g. Kye's Genius NetScroll mouse returns
vendor, but not product); the strings returned by device are still
preferred to those in the array, though
from the SCSI id it has. (this avoids the confusing umass-sim32 device. It
should have been umass-sim0 all along (there is only one), and if it is
spoken to as a SCSI device the sim should be umass32.
Make the rescan actually work. We need to fill in a target and lun wildcard
and not the SCSI id of the SIM.
Add a seatbelt.
cases the registers are not correctly set on resume.
This solves the problem of USB failing after resuming a machine.
Submitted by: mike+fbsd@medianstrip.net
PR: 18261
modules to depend on modules in the same file (uhub depends on usb) or
even on themselves (usb on usb, makes the define in usb_port.h a lot
less convoluted).
Use ANSI prototypes.
There is a number of devices that are compliant, of which the 3Com 5605 is
has been verified to work.
The driver is not perfect yet, but should be able to get you somewhere.
The driver was originally written by Lennart Augustsson, but Mike Smith
and Mike Meyer <mwm@mired.org> did the porting.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
routines from foo_watchdog() because foo_watchdog() is called at
interrupt context, and that's a no-no due to the way the USB stack
is currently set up.
What we do now is call the TX end of frame handler manually to clear
the completed transmission, then check the send queue and send off
any frames that are pending.
Also turned off the interrupt pipe stuff in if_aue, since it appears
to tickle a bug in the USB stack that I haven't found yet.
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
ums driver (mouse) and get the usb driver at the same time.
This also shows that
MODULE_VERSION(usb, 1);
MODULE_DEPEND(usb, usb, 1, 1, 1);
in the same module in one source file works.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
(which is actually a CATC Netmate).
Gee. I don't know why people make such a fuss over supporting USB ethernet
NICs. This is easier than collecting graft.
Update the license in the rio_usb.h (now rio500_usb.h) to not be GPL.
Sorry for committing that file in the first place. The change of license
was agreed to by the original author.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
- Request the maximum number of LUNs on a device if it is
a Bulk-Only device.
- Handle NO_TEST_UNIT_READY case for SCSI
- Add NO_START_STOP quirk for LS-120
- Fix a KASSERT which was the wrong way around.
- Kickstart the LS-120 with the infamous LS-120 specific command of
which no one knows what it doesn, apart from the fact that it appeared
in the Linux code someday.
kernel. Justin agress that there is no other reasonable alternative to
do automatic rescans on connect.
The problem is that when a new device attaches to a SIM (SCSI host
controller) we need to send a XPT_SCAN_BUS command to the SIM using
xpt_action. This requires however that there is a peripheral available
to take the command (otherwise xpt_done and later bomb). The RESCAN
ioctl uses the same periph.
This enables a USB mass storage drive to do an automatic rescan on
connection of the drive.
The automatic dropping of a CAM entry on disconnection was already
working (asynchronous event).
The next thing to do is find someone to commit a change to vpo to do the
same thing. Just port umass_cam_rescan and friends across to that
driver.
Approved by: gibbs
unit numbers all wrong. This did not show up because most of them where
zero anyway.
Use a separate buffer for command transforms instead of fiddling with
the existing cdb_bytes.
Take CAM_CDB_POINTER into account. Nobody is using it, but someone might
in the future.
Be more picky about what to accept in the UFI command set.
First attempt at implementing the ATAPI command protocol transforms.
This should at least make Imation Superdisk and other e-Shuttle based
devices show as attached. Maybe they even work to some extent.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
and has not been loaded via a kldload,
running usbd(8) will autoload the "usb.ko" kld.
thanks to Peter Wemm for enlightening me on the
differences between kldfind(2) and modfind(2).
to be based on the transfer speed, but I got it all wrong. The by far
biggest factor in the timeout is the start of a removable device, which
is about 2 seconds anyway.
Prodded by: Lennart Augustsson
This makes it possible to handle the done queue even when the end of tail
TD has ended up on the done queue as well (the xfer in this case is NULL
but the next field is valid, so we simply skip that element.
Make sure we mark all the handled transfers as handled.
Stop using powerhooks. They are a NetBSD-ism.
