with the correct configuration.
Occasionally an aggregate TX would fail and the first frame would be
retransmitted as a non-AMPDU frame. Since bfs_aggr=1 and bfs_nframes > 1
(from the previous AMPDU attempt), the aggr completion function would be
called and be very confused about what's going on.
Noticed by: Kim <w8hdkim@gmail.com>
PR: kern/171394
NetBSD/pc98 was never merged into the main NetBSD tree and is no longer
developed. Adding locking to these drivers would have made the compat
shims hard to impossible to maintain, so remove the shims to ease
future changes.
These changes were verified by md5. Some additional shims can be removed
that do affect the compiled results that I will probably do in another
round.
Approved by: nyan (tentatively)
have been chosen based on the bit names in the PCI Express Base
Specification 3.0, and to match the predominant style of the existing
bit definitions.
MFC after: 1 week
twe_start() to simulate the behavior on 4.x where the driver dropped
spl to allow interrupts to run to free up space in the command
queue. Be careful to only poll if we are going to make at least
one more attempt to queue the current command. Also, when polling,
be careful to not call twe_startio() to queue more commands to avoid
recursion.
- Move the buffer for formatting AEN messages into the softc instead of
using a single driver-wide static buffer.
Requested by: scottl (1)
Tested by: Mike Tancsa @ Sentex
generator, found on IvyBridge and supposedly later CPUs, accessible
with RDRAND instruction.
From the Intel whitepapers and articles about Bull Mountain, it seems
that we do not need to perform post-processing of RDRAND results, like
AES-encryption of the data with random IV and keys, which was done for
Padlock. Intel claims that sanitization is performed in hardware.
Make both Padlock and Bull Mountain random generators support code
covered by kernel config options, for the benefit of people who prefer
minimal kernels. Also add the tunables to disable hardware generator
even if detected.
Reviewed by: markm, secteam (simon)
Tested by: bapt, Michael Moll <kvedulv@kvedulv.de>
MFC after: 3 weeks
Fix the strong signal diversity capability setting - I had totally
messed up the indentation.
Set the default values to match what's in the .ini for now, rather than
what values I had previously gleaned from places. This seems to work
quite well for the early AR5212 NICs I have. Of course, later NICs
have different PHYs and the radar configuration is very card/board
dependent..
Tested:
* ath1: AR5212 mac 5.3 RF5111 phy 4.1
ath1: 2GHz radio: 0x0023; 5GHz radio: 0x0017
This detects 1, 5, 25, 50, 75, 100uS pulses reliably (with no interference.)
However, 10uS pulses don't detect reliably. That may be around the
transition between short and long pulses so some further tuning may
improve things.
up on (at least) the AR5413.
The 30 second summary - if a CRC error frame comes in during PHY error
processing, that CRC bit will be set for all subsequent frames until
a non-CRC error frame is processed.
So to allow for accurate PHY error processing (Radar, and ANI on the AR5212
HAL chips) just tag the frame as being both CRC and PHY - let the driver
decide what to do with it.
PR: kern/169362
this case, allocate a plain mbuf and copy the frame into it, then send the
copy up the stack, leaving the original mbuf+cluster in place in the
receive ring for immediate re-use. This saves a trip through 2 of the
3 zones of the compound mbuf allocator, a trip through busdma, and a trip
through the 1 of the 3 mbuf destructors. For our load at Netflix, this can
lower CPU consumption by as much as 20%. The copy algorithm is based on
investigative work from Luigi Rizzo earlier in the year.
Reviewed by: jfv
Obtained from: Netflix
the interface is brought up. Without this, the boot time interrupt
round-robin assignment does not think the allocated interrupt resources
are active and leaves them assigned to CPU 0.
While here, add descriptive tags to each interrupt handler when MSI-X
is used.
Reviewed by: np
MFC after: 1 week
some HAL definitions rather than local definitions.
The original source (ath9k) pulled this stuff from the QCA driver and
removed the HAL_* prefix. I'm just restoring the correct order of things.
Obtained from: Qualcomm Atheros
This routine is intended only for commands such as INQUIRY where
the controller may fill out a smaller amount of data than allocated
by the host.
The end result of this bug was that isci(4) would report non-zero
resid for successful SCSI_UNMAP commands.
Sponsored by: Intel
MFC after: 3 days
In fact, bus_dmamem_alloc() happily NULLs the dmat pointer passed in,
before replacing it with its own.
This fixes a MIPS crash when kldload'ing if_ath/if_ath_pci -
bus_dmamap_destroy() was passed in a NULL dmat pointer and was doing
all kinds of very bad things.
Reviewed by: scottl
This is a re-implementation based on the reference carrier code
for the AR5413.
Tested:
* Pulse detection for AR5212 and AR5413, to ensure the
correct behaviour for both chips
PR: kern/170904
Obtained from: Qualcomm Atheros
The comparison assumes maxFirstepLevel is a count, rather than a maximum
value. The array is 3 entries in size however 'maxFirstepLevel' is 2.
This bug also exists in the AR5212 HAL.
MPSAFE.
- Preallocate a full set of QCBs during attach rather than allocating new
ones on demand to avoid allocations in the I/O path.
- Remove the explicit bus space tag/handle and use bus_*() on the
relevant 'struct resource' instead.
- Defer logical drive probing to an intrhook.
- Fix ida_detach() to detach and delete child devices (logical drives).
- Update the DMA handling to support EINPROGRESS by moving the work to
submit a mapped request into the bus_dma callback routine as well as
add support for freezing the queue when EINPROGRESS is encountered.
Tested by: Marco Steinbach coco executive-computing de
Terasic DE-4 board. Allow LED configuration to be set using loader
tunables, not just from userspace, and preconfigure LED 8 as a kernel
heartbeat. For now, this is a Nexus-attached, BERI-only driver, but it
could be used with other hard and soft cores on Altera FPGAs as well, in
principle.
Sponsored by: DARPA, AFRL
used with Terasic's DE-4 and other similar FPGA boards. This display
is 800x480 and includes a capacitive touch screen, multi-touch
gesture recognition, etc. This device driver depends on a Cambridge-
provided IP core that allows the MTL device to be hooked up to the
Altera Avalon SoC bus, and also provides a VGA-like text frame buffer.
Although it is compiled as a single device driver, it actually
implements a number of different device nodes exporting various
aspects of this multi-function device to userspace:
- Simple memory-mapped driver for the MTL 24-bit pixel frame buffer.
- Simple memory-mapped driver for the MTL control register set.
- Simple memory-mapped driver for the MTL text frame buffer.
- syscons attachment for the MTL text frame buffer.
This driver attaches directly to Nexus as is common for SoC device
drivers, and for the time being is considered BERI-specific, although
in principle it might be used with other hard and soft cores on
Altera FPGAs.
Control registers, including touchscreen input, are simply memory
mapped; in the future it would be desirable to hook up a more
conventional device node that can stream events, support kqueue(2)/
poll(2)/select(2), etc.
This is the first use of syscons on MIPS, as far as I can tell, and
there are some loose ends, such as an inability to use the hardware
cursor. More fundamentally, it appears that syscons(4) assumes that
either a host is PC-like (i386, amd64) *or* it must be using a
graphical frame buffer. While the MTL supports a graphical frame
buffer, using the text frame buffer is preferable for console use.
Fixing this issue in syscons(4) requires non-trivial changes, as the
text frame buffer support assumes that direct memory access can be
done to the text frame buffer without using bus accessor methods,
which is not the case on MIPS. As a workaround for this, we instead
double-buffer and pretend to be a graphical frame buffer exposing
text accessor methods, leading to some quirks in syscons behaviour.
Sponsored by: DARPA, AFRL
The driver attempts to support all documented parts, but has only been
tested with the 512Mbit part on the Terasic DE4 FPGA board. It should be
trivial to adapt the driver's attach routine to other embedded boards
using with any parts in the family.
Also import isfctl(8) which can be used to erase sections of the flash.
Sponsored by: DARPA, AFRL
which presents a UART-like interface over the Avalon bus that can be
addressed over JTAG. This IP core proves extremely useful, allowing us to
connect trivially to the FreeBSD console over JTAG for FPGA-embedded hard
and soft cores. As interrupts are optionally configured for this soft
core, we support both interrupt-driven and polled modes of operation,
which must be selected using device.hints. UART instances appear in /dev
as ttyu0, ttyu1, etc.
However, it also contains a number of quirks, which make it difficult to
tell when JTAG is connected, and some buffering issues. We work around
these as best we can, using various heuristics.
While the majority of this device driver is not only not BERI-specific,
but also not MIPS-specific, for now add its defines in the BERI files
list, as the console-level parts are aware of where the first JTAG UART
is mapped on Avalon, and contain MIPS-specific address translation, to
use before Newbus and device.hints are available.
Sponsored by: DARPA, AFRL
