RTL810x family , RTL8139 has different register map for Config
registers.
While here, follow the lead of re(4) in WOL configuration.
- Disable WOL_UCAST and WOL_MCAST capabilities by default.
- Config5 register write does not need to unlock EEPROM access
on RTL8139 family but unlocking EEPROM access does not affect
its operation and make it consistent with re(4).
Reported by: Matt Renzelmann mjr <> cs dot wisc dot edu
- Remove all attempts to guess physical temperature using DiodeOffset.
There are too many reports that it varies wildly depending on motherboard.
Instead, if it is known to scale well and its offset is known from other
temperature sensors on board, the user may set "dev.amdtemp.0.sensor_offset"
tunable to compensate the difference. Document the caveats in amdtemp(4).
- Add a quirk for Socket AM2 Revision G processors. These processors are
known to have a different offset according to Linux k8temp driver.
- Warn about Family 10h Erratum 319. These processors have broken sensors.
- Report temperature in more logical orders under dev.amdtemp node. For
example, "dev.amdtemp.0.sensor0.core0" is now "dev.amdtemp.0.core0.sensor0".
- Replace K8, K10 and K11 with official processor names in amdtemp(4).
I'm not sure _why_ the ic is NULL here, but I've seen it occasionally do
this after I've been tinkering with things for a while. It ends up
crashing in a call to ath_chan_set() via the net80211 scan code and scan
task.
don't give RX path more priority than TX path.
Also remove infinite loop in interrupt handler and limit number of
iteration to 32. This change addresses system load fluctuations
under high network load.
found on Adaptec AIC-6915 Starfire ethernet controller.
While here, use status register to know resolved speed/duplex.
With this change, sf(4) correctly reports speed/duplex of
established link.
Reviewed by: marius
- In case the parent is bge(4), don't set the Jumbo frame settings unless
the MAC actually is Jumbo capable as otherwise the PHY might not have the
corresponding registers implemented. This is also in line with what the
Linux tg3 driver does.
PR: 165032
Submitted by: Alexander Milanov
Obtained from: OpenBSD
MFC after: 3 days
hold the lock.
This is part of my series of work to try and capture when net80211
locking isn't.
ObNote: it'd be nice to be able to mark a lock as "assert if the lock
is dropped", so I could capture functions which decide that dropping
and reacquiring the lock is a good idea (without re-checking the
sanity of the state protected by the lock.)
devices that are unplugged via QEMU.
sys/dev/xen/blkback/blkback.c:
Toolstack initiated closures change the frontend's state
to Closing. The backend must change to Closing as well,
even if we can't actually close yet, in order for the
frontend to notice and start the closing process.
MFC after: 3 days
- remove the KEVENT code, which was incomplete and not compiled anyways;
- change some while() loops into for()
- adjust indentation
- remove extra whitespace
MFC after: 1 week
struct ccb_pathinq from sys/cam/cam_ccb.h wasn't added to stable/7 at all
and didn't appear in stable/8 until svn R195534. Since __FreeBSD_version
did not get bumped until svn R195634, assume that maxio is valid at 800102
or higher.
Obtained from: Yahoo! Inc.
MFC after: 0 days
with RX/TX halting.
* Always disable/enable interrupts during a channel change, just to simply
things.
* Ensure that the ath taskqueue has completed and is paused before
continuing.
This dramatically reduces the instances of overlapping RX and reset
conditions.
PR: kern/165220
The previous code did not limit the I/O request size based on
the maximum number of segments supported by the back-end. In
current practice, since the only back-end supporting chained
requests is the FreeBSD implementation, this limit was never
exceeded.
sys/dev/xen/blkfront/block.h:
Add two macros, XBF_SEGS_TO_SIZE() and XBF_SIZE_TO_SEGS(),
to centralize the logic of reserving a segment to deal with
non-page-aligned I/Os.
sys/dev/xen/blkfront/blkfront.c:
o When negotiating transfer parameters, limit the
max_request_size we use and publish, if it is greater
than the maximum, unaligned, I/O we can support with
the number of segments advertised by the backend.
o Don't unilaterally reduce the I/O size published to
the disk layer by a single page. max_request_size
is already properly limited in the transfer parameter
negotiation code.
o Fix typos in printf strings:
"max_requests_segments" -> "max_request_segments"
"specificed" -> "specified"
MFC after: 1 day
Introduce some functions to map NIC ring indexes into netmap ring
indexes and vice versa. This way we can implement the bound
checks only in one place (and hopefully in a correct way).
On passing, make the code and comments more uniform across the
various drivers.
FreeBSD's front and back Xen blkif interface drivers.
sys/dev/xen/blkfront/block.h:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkback/blkback.c:
Replace FreeBSD specific multi-page ring impelementation with
support for both the Citrix and Amazon/RedHat versions of this
extension.
sys/dev/xen/blkfront/blkfront.c:
o Add a per-instance sysctl tree that exposes all negotiated
transport parameters (ring pages, max number of requests,
max request size, max number of segments).
o In blkfront_vdevice_to_unit() add a missing return statement
so that we properly identify the unit number for high numbered
xvd devices.
sys/dev/xen/blkback/blkback.c:
o Add static dtrace probes for several events in this driver.
o Defer connection shutdown processing until the front-end
enters the closed state. This avoids prematurely tearing
down the connection when buggy front-ends transition to the
closing state, even though the device is open and they
veto the close request from the tool stack.
o Add nodes for maximum request size and the number of active
ring pages to the exising, per-instance, sysctl tree.
o Miscelaneous style cleanup.
sys/xen/interface/io/blkif.h:
o Add extensive documentation of the XenStore nodes used to
implement the blkif interface.
o Document the startup sequence between a front and back driver.
o Add structures and documenatation for the "discard" feature
(AKA Trim).
o Cleanup some definitions related to FreeBSD's request
number/size/segment-limit extension.
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkback/blkback.c:
sys/xen/xenbus/xenbusvar.h:
Add the convenience function xenbus_get_otherend_state() and
use it to simplify some logic in both block-front and block-back.
MFC after: 1 day
This allows LUNs greater than 0 to be probed. It can be increased later if
need be.
This brings back SVN rev 224973, which was inadvertently removed with the
import of the LSI driver.
Reported by: dwhite
MFC after: 3 days
The lang/gcc* ports patch headers where they think something is
non-standard. These patched headers override the system headers which means
you have to rebuild these ports whenever you do installworld to make sure
they contain the latest changes.
MOD_SHUTDOWN is not an end of existence, and there is a life after it.
In particular, code previously called on MOD_SHUTDOWN grabbed lock and
deallocated unit numbering. That caused infinite wait loop if snd_uaudio
tried to destroy its PCM device after that point.
MFC after: 3 days
through by VMware so blacklist their PCI-PCI bridge for MSI/MSI-X here.
Note that besides currently there not being a quirk type that disables
MSI-X only and there's no evidence that MSI doesn't work with the VMware
pass-through, it's really questionable whether MSI generally works in
that setup as VMware only mention three know working devices [1, p. 4].
Also not that this quirk entry currently doesn't affect the devices
emulated by VMware in any way as these don't claim support MSI/MSI-X to
begin with. [2]
While at it, make the PCI quirk table const and static.
- Remove some duplicated empty lines.
- Use DEVMETHOD_END.
PR: 163812, http://forums.freebsd.org/showthread.php?t=27899 [2]
Reviewed by: jhb
MFC after: 3 days
