igb now has a queue notion that has a single interrupt
with an RX/TX pair, this will reduce the total interrupts
seen on a system. Both em and igb have a new watchdog
method. igb has fixes from Pyun Yong-Hyeon that have
improved stability, thank you :)
I wish to MFC this for 7.3 asap, please test if able.
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
the intention of having two ttys pointing to the same cfe console device was.
Also we were not initializing the output[] array passed in as input to
tty_makedev() so one name of the ttys was garbage.
Fix the code that calls cfe_write() to deal with the case where only a partial
buffer is written out.
cfe_cngetc() needs to return if there is no character available as input.
If we don't do this then the cfe_timeout() function will spin forever
because cfe_cngetc() will only ever return if there is valid input.
Approved by: imp (mentor)
frontend uses the same uPD7210 backend as the pcii ISA frontend, so
the backend has to cope with both situations.
Also, hide the first printf in pcii_probe (address mismatch) behind
bootverbose as the ISA bus parent tries to probe all configured ISA
devices against each driver, so a the console has been cluttered with
this message for a bunch of unrelated driver probes.
MFC after: 3 days
. Properly allocate all IO space resources. These cards scatter their
IO addresses over a range of 0x1600 bytes, and they require an
additional address for "special interrupt handling".
. Implement the "special interrupt handling" per the GPIB-PCIIA
Technical Reference Manual; this was apparently not declared for the
clone card this driver has been originally implemented for, but it
turned out to be needed for both, an original NI brand PCII/PCIIA
card as well as the Axiom AX5488 clone.
. Add some diagnostic messages for various resource allocation etc.
failures during probe.
. Add some comments about the structure of the IO address space that
is used by these cards.
MFC after: 1 day
implementation of heartbeat interval was 2 but there was typo which
caused the heartbeat is sent approximately every 5 seconds. This
caused unintended controller reset by firmware because firmware
thought OS was crashed.
Submitted by: Floris Bos < info <> je-eigen-domein dot nl >
Tested by: Andrzej Tobola < ato <> iem dot pw dot edu dot pl >
loopback.
- Change the meaning of "mix" OSS control. Now it controls loopback level,
according to comments in soundcard.h.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
frames to be accepted while the driver is resetting the hardware.
This failure is generally observed when broadcast frames are received
during driver load and will generate "Unable to write CTX memory"
errors.
- Small changes to driver flags display.
This is not only a prudent thing to do, but also makes sure that probe
method is not confused by non-NULL 'private', if the previous attach
attempt fails for any reason.
PR: kern/142561
Tested by: Alex Goncharov <alex-goncharov@comcast.net>
MFC after: 4 days
chains. This part of code is to enhance performance so failing the
collapsing should not free TX frames. Otherwise bge(4) will
unnecessarily drop frames which in turn can freeze the network
connection.
Reported by: Igor Sysoev (is <> rambler-co dot ru)
Tested by: Igor Sysoev (is <> rambler-co dot ru)
copper and fiber interfaces over GMII so an explicit check is
necessary to know whether it was configured for fiber interface.
This change make BCM5715S work.
Tested by: olli
MFC after: 1 week
over GMII, make sure to enable GMII. With this change brgphy(4) is
used to handle the dual mode PHY. Since we still don't have a sane
way to pass PHY specific information to mii(4) layer special
handling is needed in brgphy(4) to determine which mode of PHY was
configured in parent interface.
This change make BCM5715S work.
Tested by: olli
Obtained from: OpenBSD
MFC after: 1 week
o Don't enable BGE_FLAG_BER_BUG on both 5722 and 5756, and based
on their PCI IDs rather than their chip IDs.
Reported by: several PC-BSD users via kmoore
Reviewed by: yongari, imp, jhb, davidch
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
from standard 3G wireless units by supplying a raw IP/IPv6 endpoint rather than
using PPP over serial. uhsoctl(1) is used to initiate and close the WAN
connection.
Obtained from: Fredrik Lindberg <fli@shapeshifter.se>
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_READ(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
MFC after: 1 month
now due to unidentified synchonization problem. For 7.1 soundcards 5.1
support handled correctly via software upmix done by sound(4).
Stereo stream is no more duplicated to all ports. If you loose sound, check
you are using right connectors. Front speakers connector is usually green,
center/LFE - orange, rear - black, side - gray.
Pertinant highlights from Myricom CHANGES file include:
- Make sure invalid external smbus activity cannot affect performance
- Fix to avoid a bug where the link could sometimes stay reported as
up on after unplugging the cable.
- For 8B NIC, make smbus connection passive at init to avoid
possible address conflicts
- Increase number of slices to 17 for multi-slice fw
- Fix a bug where packets dropped because of link_overflow could
be occasionally reported as bad_crc32
- Add selectable failover strategy for dual-port chip: symmetric or primary/backup
- On failover, send RARP broadcast to make the change immediately
known to the network
- Change endianess for PCI Device Serial Number
- For dual-port NICs, time to failover is now a few microsecs
instead of a few millisecs.
MFC after: 3 days
