- Trade off granularity to reduce overhead, since the current model
doesn't appear to reduce contention substantially: move to a single
harvest mutex protecting harvesting queues, rather than one mutex
per source plus a mutex for the free list.
- Reduce mutex operations in a harvesting event to 2 from 4, and
maintain lockless read to avoid mutex operations if the queue is
full.
- When reaping harvested entries from the queue, move all entries from
the queue at once, and when done with them, insert them all into a
thread-local queue for processing; then insert them all into the
empty fifo at once. This reduces O(4n) mutex operations to O(2)
mutex operations per wakeup.
In the future, we may want to look at re-introducing granularity,
although perhaps at the granularity of the source rather than the
source class; both the new and old strategies would cause contention
between different instances of the same source (i.e., multiple
network interfaces).
Reviewed by: markm
be used to announce various system activity.
The auxio device provides auxiliary I/O functions and is found on various
SBus/EBus UltraSPARC models. At present, only front panel LED is
controlled by this driver.
Approved by: jake (mentor)
Reviewed by: joerg
Tested by: joerg
with acpi but the timer runs twice as fast. Note that the main problem
(system doesn't work properly with acpi disabled) should be fixed separately.
Changes:
* Add a quirk to disable the timer
* Merge the P5A and P5A-B quirks since they appear to be based on the
same ASL.
PR: i386/72450
Tested by: Kevin Oberman <oberman es.net>
MFC after: 3 days
This also adds support for bigger disks on the controller I have access to,
and maybe others if I understood the adhoc methods used on those.
Those with more PC98 bigdrive controllers it is hereby invited to add/fix
support for those in geom_pc98.c and not using #ifdef PC98 all over the place.
allocate unallocated memory resources from the top 32MB of the address
space rather than the top 2GB. While the latter works on some
chipsets, it fails badly on others. 32MB is more conservative and
matches what cheap harware from this era is hardwired to pass.
table. acpidump(8) concatenates the body of the DSDT and SSDTs so an
edited ASL will contain all the necessary information. We can't use a
completely empty table since ACPI-CA reports this as a problem.
MFC after: 3 days
+ * 9: 0x3f0-0x3f3,0x3f4-0x3f5,0x3f7
This requires only one change to support. Rather than keying on the
size of the resource being 2, instead key off the end & 7 being 3.
This covers the same cases that the size of 2 would catch, but also
covers the new above case.
In addition, I think it is clearer to use the end in preference to the
size and start for case #8 as well. Turns two tests into one, and
catches no other cases.
Make minor commentary changes to deal with new case #9.
# This change is specifically minimal to allow easy MFC. A more
# extensive change will go into current once I've had a chance to test
# it on a lot of hardware...
data endpoints. The control endpoint doesn't need read/write/poll
operations, and more importantly, the thread counts should be
separate so that the control endpoint can properly reference itself
while deleting and recreating the data endpoints.
* Add some macros that handle referencing/releasing devices, and use them
for sleeping/woken-up and open/close operations as apppropriate.
* Use d_purge for FreeBSD, and a loop testing the open status for all
the endpoints for NetBSD and OpenBSD, so that when the device is
detached, the right thing always happens.
restart the current waiting transfer. If this isn't done, the device's
next transfer (that we would like to do a short read on) is going to
return an error -- for short transfer.
* For bulk transfer endpoints, restore the maximum transfer length each
time a transfer is done, or the first short transfer will make all the
rest that size or smaller.
* Remove impossibilities (malloc(M_WAITOK) == NULL, &var == NULL).
New device names are "{tty|cua}A$(card)$(port)[.init|.lock]"
Put a portname in the port structure if SI_DEBUG is defined to avoid
need to inspect minor number to construct name..
Constify some strings.
Remove duplicated DBG_ #defines.
is a no-op on little endian architectures, but fixes getting the MAC
address for some dc(4) cards on big endian architectures.
This is a RELENG_5 candidate.
Tested by: gallatin (powerpc), marius (sparc64)
First version of the patch written by: gallatin
people have reported problems (stickyness, aiming difficulty) which is proving
difficult to fix, so this will default to disable until sometime after 5.3R.
To enable Synaptics support, set the 'hw.psm.synaptics_support=1' tunable.
MT5 candidate.
Approved by: njl
in the actual _FDE parsing. If the failure occurs earlier such as in
fdc_attach() then don't try to probe any drives.
MFC after: 3 days
Reviewed by: njl
Tested by: Christian Laursen xi at borderworlds dot dk
to make sure the pipe is ready. Some devices apparently don't support
the clear stall command however. So what happens when you issue such
devices a clear stall command? Typically, the command just times out.
This, at least, is the behavior I've observed with two devices that
I own: a Rio600 mp3 player and a T-Mobile Sidekick II.
It used to be that after the timeout expired, the pipe open operation
would conclude and you could still access the device, with the only
negative effect being a long delay on open. But in the recent past,
someone added code to make the timeout a fatal error, thereby breaking
the ability to communicate with these devices in any way.
I don't know exactly what the right solution is for this problem:
presumeably there is some way to determine whether or not a device
supports the 'clear stall' command beyond just issuing one and waiting
to see if it times out, but I don't know what that is. So for now,
I've added a special case to the error checking code so that the
timeout is once again non-fatal, thereby letting me use my two
devices again.
This changes the naming of USB serial devices to: /dev/ttyU%d and
/dev/cuaU%d for call-in and call-out devices respectively. (Please
notice: capital 'U')
Please also note that we now have .init and .lock devices for USB
serial ports. These are not persistent across device removal. devd(8)
can be used to configure them on attachment time.
These changes also improve the chances of the system surviving if
the USB device is unplugged at an inconvenient time. At least we
do not rip things apart while there are any threads in the device
driver anymore.
Remove cdevsw, rely on the tty generic one.
Don't make_dev(), use ttycreate() which does all the magic.
In detach, do close procesing if we ripped things apart
while the device was open. Call ttyfree() once we're done
cleaning up.
select(2), and discovered to my horror that ugen(4)'s bulk in/out support
is horribly lobotomized. Bulk transfers are done using the synchronous
API instead of the asynchronous one. This causes the following broken
behavior to occur:
- You open the bulk in/out ugen device and get a descriptor
- You create some other descriptor (socket, other device, etc...)
- You select on both the descriptors waiting until either one has
data ready to read
- Because of ugen's brokenness, you block in usb_bulk_transfer() inside
ugen_do_read() instead of blocking in select()
- The non-USB descriptor becomes ready for reading, but you remain blocked
on select()
- The USB descriptor becomes ready for reading
- Only now are you woken up so that you can ready data from either
descriptor.
The result is select() can only wake up when there's USB data pending. If
any other descriptor becomes ready, you lose: until the USB descriptor
becomes ready, you stay asleep.
The correct approach is to use async bulk transfers, so I changed
the read code to use the async bulk transfer API. I left the write
side alone for now since it's less of an issue.
Note that the uscanner driver has the same brokenness in it.
to 7422 since it appears that the 8169S can't transmit anything larger..
The 8169S can receive full jumbo frames, but we don't have an mru to let
the upper layers know this...
add fixup so that this driver should work on alignment constrained platforms
(!i386 && !amd64)
MFC after: 5 days
