During H1 message parsing, the Upgrade header values are checked to detect
"websocket" prototol, to properly handle websocket upgrades between H1 and
H2 and to possibly reject messages if mandatory headers are missing.
However, the flag is reset for each new Upgrade header and the information
may be lost. So never reset it.
This patch must be backported as far as 2.4.
As reported by Huangbin Zhan (@zhanhb) in github issue #3355, latest
commit 96f7ff4fdd ("MINOR: mux-h2: add a new message flag to indicate
ext connect support") was not correct and can break RFC8441-compliant
clients, as it did for them with a variant of Chrome 142.
The problem is that while RFC9113 says that new pseudo-headers are only
permitted with *negotiated* extensions, and RFC8441 doesn't indicate
whether or not SETTINGS_ENABLE_CONNECT_PROTOCOL is needed from clients,
it only says that clients know that servers support the extension when
seeing it in their settings and can use it, which seems to imply that
they don't need to send it to indicate their willingness to use it.
This also means that the server cannot know if a client is expected to
use it or not by default. It only know that a client is not allowed to
use it if the server didn't emit support mentioning it, which haproxy
can do using h2-workaround-bogus-websocket-clients.
Thus the fix proposed by @zhanhb is right, when presetting the flag for
the parser to indicate whether or not we're willing to accept RFC8441's
:protocol pseudo-header, we should:
- consider the received setting on the backend side (though the
pseudo-header is neither used nor supported there, but at least
we pass the info regarding the support of the extension)
- consider the configuration for the frontend (since it's the only
place where we can decide on support or not)
This patch does just that and reverts the accompanying changes to the
regtests that made them want to see the client's setting. It must be
backported to 2.6.
In the mean time, placing this option in the global section will force
the clients to downgrade to h1:
h2-workaround-bogus-websocket-clients
Many thanks again to @zhanbb this feedback and proposing a tested fix.
The tests were validating extended connect without sending the setting
in the client settings frame. It currently works due to a bug, so let's
fix the vtc first.
By default when building an H2 request, vtest sets the END_STREAM flag
on the HEADERS frame. This is problematic with the websocket and proto
upgrade tests since we're using CONNECT, because it immediately closes
afterwards, which does not correspond to what we're testing. Doing this
in abortonclose mode rightfully produces an error. Let's fix the test
so as not to set the flag on the HEADERS frame. However, doing so means
we'll receive a window update that we must also accept. Now the test
works both with and without abortonclose.
When threads are enabled and running on a machine with multiple CCX
or multiple nodes, thread groups are now enabled since 3.3-dev2, causing
load-balancing algorithms to randomly fail due to incoming connections
spreading over multiple groups and using different load balancing indexes.
Let's just force "thread-groups 1" into all configs when threads are
enabled to avoid this.
Every reg-test now runs without any warning, so let's acivate -dW by
default so the new ones will inheritate the option.
This patch reverts 9d511b3c ("REGTESTS: enable -dW on almost all tests
to fail on warnings") and adds -dW in the default HAPROXY_ARGS of
scripts/run-regtests.sh instead.
Now that warnings were almost all removed, let's enable zero-warning
via -dW. All tests were adjusted, but two:
- mcli/mcli_start_progs.vtc:
the programs section currently cannot be silenced
- stats/stats-file.vtc:
the warning comes from the stats file itself on comment lines.
All other ones are now OK.
Since the commit f2b02cfd9 ("MAJOR: http-ana: Review error handling during
HTTP payload forwarding"), during the payload forwarding, we are analyzing a
side, we stop to test the opposite side. It means when the HTTP request
forwarding analyzer is called, we no longer check the response side and vice
versa.
Unfortunately, since then, the HTTP tunneling is broken after a protocol
upgrade. On the response is switch in TUNNEL mode. The request remains in
DONE state. As a consequence, data received from the server are forwarded to
the client but not data received from the client.
To fix the bug, when both sides are in DONE state, both are switched in same
time in TUNNEL mode if it was requested. It is performed in the same way in
http_end_request() and http_end_response().
This patch should fix the issue #2125. It is 2.8-specific. No backport
needed.
With the CI occasionally slowing down, we're starting to see again some
spurious failures despite the long 1-second timeouts. This reports false
positives that are disturbing and doesn't provide as much value as this
could. However at this delay it already becomes a pain for developers
to wait for the tests to complete.
This commit adds support for the new environment variable
HAPROXY_TEST_TIMEOUT that will allow anyone to modify the connect,
client and server timeouts. It was set to 5 seconds by default, which
should be plenty for quite some time in the CI. All relevant values
that were 200ms or above were replaced by this one. A few larger
values were left as they are special. One test for the set-timeout
action that used to rely on a fixed 1-sec value was extended to a
fixed 5-sec, as the timeout is normally not reached, but it needs
to be known to compare the old and new values.
Test the conformance of websocket rfc6455 in haproxy. In particular, if
a missing key is detected on a h1 message, haproxy must close the
connection.
Note that the case h2 client/h1 srv is not tested as I did not find a
way to calculate the key on the server side.
