Clarify the behavior of negated addresses within the `blackhole`
statement to prevent common configuration misunderstandings.
(cherry picked from commit 2b23c7011e)
To prevent spoofed unsigned DNAME responses being accepted retry
response with unsigned DNAMEs over TCP if the response is not TSIG
signed or there isn't a good DNS CLIENT COOKIE.
(cherry picked from commit 2e40705c06)
The randomized order of the records in the rrset is not uniform across
all permutations. Clarify this in the documentation.
(cherry picked from commit 369c8dc388)
The "tkey-domain" statement has effectively been a no-op since commit
bd4576b3ce, which removed the only bit of
code using it: the logic implementing TKEY Mode 2 (Diffie-Hellman).
A subsequent cleanup commit, 885c132f4a,
also missed the opportunity to remove the "tkey-domain" statement
altogether.
Mark the "tkey-domain" statement as obsolete and remove all code and
documentation related to it.
(cherry picked from commit 805f1c0f65)
Clarify that forwarding points to a resolver and stub to auths.
Add cross-links. Rewrite stub zone type description.
(cherry picked from commit e84b98a9fc)
When a DNS Response Policy Service (DNSRPS) interface is used, the
'servfail-until-ready yes' option is ignored, because RPZ zones are
not processed by BIND.
By default, when named is started it may start answering to
queries before the response policy zones are completely loaded
and processed. This new feature gives an option to the users to
tell named that incoming requests should result in SERVFAIL anwser
until all the response policy zones are procesed and ready.
(cherry picked from commit 41387b8d30)
Add a new option 'manual-mode' to 'dnssec-policy'. The intended
use is that if it is enabled, it will not automatically move to the
next state transition (RUMOURED, UNRETENTIVE), only after manual
confirmation. The intended state transition should be logged.
(cherry picked from commit 63c5b453e0)
When the interface-interval parser was changed from uint32 parser to
duration parser, the default value stayed at plain 60 which now means 60
seconds instead of 60 minutes. Fix the default value and the
documentation to match the reality.
(cherry picked from commit de08c0088d)
This new option sets the delay, in seconds, to wait before sending
a set of NOTIFY messages for a zone. Whenever a NOTIFY message is
ready to be sent, sending will be deferred for this duration.
(cherry picked from commit e42d6b4810)
The new intended behavior is that 'max-clients-per-query' value is
raised to equal 'clients-per-query' if it is lower.
(cherry picked from commit f50753f303)
Expose the average transfer rate (in bytes-per-second) during the
last full 'min-transfer-rate-in <bytes> <minutes>' minutes interval.
If no such interval has passed yet, then the overall average rate is
reported instead.
(cherry picked from commit c701b590e4)
Some detected links are not to be verified (127.*, dnssec-or-not.com)
and some I can't fix (flaticon, godaddy, icann), but they are not
crucial.
(cherry picked from commit 8302469507)
The 'remote-servers' named.conf reference conflicts with the standard
term from the glossary. Rename the standard term to server-list to
make the docs build.
(cherry picked from commit 726c9cd73b)
Having zone statements that are also top blocks is confusing, and if
we want to add more in the future (which I suspect will be for
generalized notifications, multi-signer), we need to duplicate a lot
of code.
Remove top blocks 'parental-agents' and 'primaries' and just have one
top block 'remote-servers' that you can refer to with zone statements.
(cherry picked from commit b121f02eac)
Add a none parameter to named configuration option `query-source` (respectively `query-source-v6`) which forbid usage of IPv4 (respectively IPv6) addresses when named is doing an upstream query.
Closes#4981 Turning-off upstream IPv6 queries while still listening to downstream queries on IPv6.
Merge branch 'colin/querysource-none' into 'main'
See merge request isc-projects/bind9!9727
Backport of MR !9727
Some changes had to be done to the existing 9.20.x code in order to
make this backport compatible:
- first, the 9.20.x branches support the `port` parameter in
query-source[-v6], where 9.21.x does not. The original changes
depend on things that can't be backported because that would break
`port` support.
- second, the changes remove the optional `address` parameter from the
canonical form. So `query-source address <ip>` is now printed as
`query-source <ip>`. This means that `named-checkconf -p` will now
generate different output if users have `query-source address <ip>` or
`query-source address <ip> port <port>`; it will now generate
`query-source <ip>` or `query-source <ip> port <port>`. This is a
non-breaking change, because the parser has been updated to support
this form as well.
Changing the default for max-recursion-queries from 100 to 32 was too
strict in some cases, especially lookups in reverse IPv6 trees started
to fail more frequently. From issue #4921 it looks like 50 is a better
default.
Now that we have 'max-query-count' as a global limit of outgoing queries
per client request, we can increase the default for
'max-recursion-queries' again, as the number of recursive queries is
no longer bound by the multiple of 'max-recursion-queries' and
'max-query-restarts'.
(cherry picked from commit 84df920d9e)
Add another option to configure how many outgoing queries per
client request is allowed. The existing 'max-recursion-queries' is
per restart, this one is a global limit.
(cherry picked from commit bbc16cc8e6)
When `sig-validity-interval` was obsoleted, the text that the signature
validity interval should be multiples of the SOA expire interval was
removed. Restore this text to the description of the
`signatures-validity` option.
(cherry picked from commit b09230004b)
The statements that already exist in the grammar can't be created with
the namedconf:statement. Use a plain definition list for these
statements and add a manual anchor for each one so links to them can be
created.
Avoid using the :any: syntax in the definition lists, as that just
creates a link to the duplicate and completely unrelated statement,
which just makes the documentation more confusing.
Add notes to the 'fetches-per-zone' and 'fetches-per-server' clauses
documentation to document that prefetches are exempted.
(cherry picked from commit ad329ddcaa)
Add a new configuration option to enable Offline KSK key management.
Offline KSK cannot work with CSK because it splits how keys with the
KSK and ZSK role operate. Therefore, one key cannot have both roles.
Add a configuration check to ensure this.
(cherry picked from commit 0598381236)
implement, document, and test the 'max-query-restarts' option
which specifies the query restart limit - the number of times
we can follow CNAMEs before terminating resolution.
(cherry picked from commit 104f3b82fb)
Previously, the number of RR types for a single owner name was limited
only by the maximum number of the types (64k). As the data structure
that holds the RR types for the database node is just a linked list, and
there are places where we just walk through the whole list (again and
again), adding a large number of RR types for a single owner named with
would slow down processing of such name (database node).
Add a configurable limit to cap the number of the RR types for a single
owner. This is enforced at the database (rbtdb, qpzone, qpcache) level
and configured with new max-types-per-name configuration option that
can be configured globally, per-view and per-zone.
Previously, the number of RRs in the RRSets were internally unlimited.
As the data structure that holds the RRs is just a linked list, and
there are places where we just walk through all of the RRs, adding an
RRSet with huge number of RRs inside would slow down processing of said
RRSets.
Add a configurable limit to cap the number of the RRs in a single RRSet.
This is enforced at the database (rbtdb, qpzone, qpcache) level and
configured with new max-records-per-type configuration option that can
be configured globally, per-view and per-zone.
Changed the default value for 'allow-transfer' to 'none'; zone
transfers now require explicit authorization.
Updated all system tests to specify an allow-transfer ACL when needed.
Revised the ARM to specify that the default is 'none'.
The mechanism was published as RFC 8509. I've briefly looked at diff
between versions -08 and the RFC and did not find significant protocol
change. Quick manual check confirms what we seem to comply with the
published protocol.
Draft was eventually published as RFC 9276 but we did not update our
docs. Also add couple mentions in relevant places in the ARM and
dnssec-signzone man page, mainly around "do not touch" places.
