This change adds a "none" parameter to the query-source[-v6]
options in named.conf, which forbid the usage of IPv4 or IPv6
addresses when doing upstream queries.
On some slow systems, the test might intermittently fail due to inherent
timing issues. In our CI, this most often happens in the
system:gcc:8fips:amd64 jobs.
Add query counters for DoT, DoH, unencrypted DoH and their proxied
counterparts. The protocols don't increment TCP/UDP counters anymore
since they aren't the same as plain DNS-over-53.
The usage of port and tls arguments in *-source and *-source-v6 named
configuration options has been previously removed. Remove
configuration check deprecating usage of those arguments.
Reintroduce logic to apply diffs when the number of pending tuples is
above 128. The previous strategy of accumulating all the tuples and
pushing them at the end leads to excessive memory consumption during
transfer.
This effectively reverts half of e3892805d6
To enable FIPS mode at runtime use 'delv -F'. The operating system
must have FIPS support available for this to succeed. This is on
by default when built with --enable-fips-mode.
To enable FIPS mode at runtime use 'dig -F'. The operating system
must have FIPS support available for this to succeed. This is on
by default when built with --enable-fips-mode.
When a test is re-run by the flaky plugin, the TestReport outcomes
collected in the pytest_runtest_makereport() hook should be overriden.
Each of the setup/call/teardown phases is reported again and since we
care about the overall outcome, their respective results should be
overriden so that only the outcome from the final test (re)run gets
reported.
Prior to this change, it lead to a situation where an extra_artifact
generated during the test might be ignored. This was caused because the
check was skipped, since the test was incorrectly considered as "failed"
in the case where the test would fail on the first run, but pass on a
subsequent flaky rerun.
QPDB is now a default implementation for both cache and zone. Remove
the venerable RBTDB database implementation, so we can fast-track the
changes to the database without having to implement the design changes
to both QPDB and RBTDB and this allows us to be more aggressive when
refactoring the database design.
Prior to introducing the pytest runner, clean.sh files were used as a
list of files that the test is expected to leave around as artifacts and
check that no extra files were created.
With the pytest runner, those scripts are no longer used, but the
ability to detect extraneous files is still useful. Add a new
"extra_artifacts" mark which can be used for the same purpose.
Originally, the dns_dbversion_t was typedef'ed to void type. This
allowed some flexibility, but using (void *) just removes any
type-checking that C might have. Instead of using:
typedef void dns_dbversion_t;
use a trick to define the type to non-existing structure:
typedef struct dns_dbversion dns_dbversion_t;
This allows the C compilers to employ the type-checking while the
structure itself doesn't have to be ever defined because the actual
'storage' is never accessed using dns_dbversion_t type.
Originally, the dns_dbnode_t was typedef'ed to void type. This allowed
some flexibility, but using (void *) just removes any type-checking that
C might have. Instead of using:
typedef void dns_dbnode_t;
use a trick to define the type to non-existing structure:
typedef struct dns_dbnode dns_dbnode_t;
This allows the C compilers to employ the type-checking while the
structure itself doesn't have to be ever defined because the actual
'storage' is never accessed using dns_dbnode_t type.
The query-source option has the slight quirk of allowing the address to
be specified in two ways, either as every other source option, or as an
"address" key-value pair.
For this reason, it had a separate parsing function from other X-source
options, but it is possible to extend the parsing of other X-sources to
be generic and also handle query-source.
This commit just does that.
The isc/crypto.h now directly includes the OpenSSL headers (evp.h) and
any application that includes that header also needs to have
OPENSSL_CFLAGS in the Makefile.am. Adjust the required automake files
as needed.
dnssec-ksr can now sign KSR files with multiple KSKs. A planned KSK
rollover is supported, meaning the KSR will first be signed with
one KSK and later with another. The timing metadata for CDS and
CDNSKEY records are also taken into account, so these records are
only published when the time is between "SyncPublish" and "SyncDelete".
Add a test case for Offline KSK where during the lifespan of the Signed
Key Response a KSK rollover happens. Ensure that the correct DNSKEY,
CDNSKEY, and CDS records are published at the right times.
When the zone is initially signed, the CDNSKEY/CDS RRset is not
immediately published. The DNSKEY and signatures must propagate first.
Adjust the test to allow for this case.
Add an option to dnssec-ksr keygen, -o, to create KSKs instead of ZSKs.
This way, we can create a set of KSKS for a given period too.
For KSKs we also need to set timing metadata, including "SyncPublish"
and "SyncDelete". This functionality already exists in keymgr.c so
let's make the function accessible.
Replace dnssec-keygen calls with dnssec-ksr keygen for KSK in the
ksr system test and check keys for created KSKs as well. This requires
a slight modification of the check_keys function to take into account
KSK timings and metadata.
In the ksr system test, the test_ksr_twotone case may fail if there
are two keys with the same keytag (but different algorithms), because
one key is expected to be signing and the other is not.
Switch to regular expression matching and include the algorithm in the
search string.
Configuration files in system tests which require some variables (e.g.
port numbers) filled in during test setup, can now use jinja2 templates
when `jinja2` python package is available.
Any `*.j2` file found within the system test directory will be
automatically rendered with the environment variables into a file
without the `.j2` extension by the pytest runner. E.g.
`ns1/named.conf.j2` will become `ns1/named.conf` during test setup. To
avoid automatic rendering, use `.j2.manual` extension and render the
files manually at test time.
New `templates` pytest fixture has been added. Its `render()` function
can be used to render a template with custom test variables. This can be
useful to fill in different config options during the test. With
advanced jinja2 template syntax, it can also be used to include/omit
entire sections of the config file rather than using `named1.conf.in`,
`named2.conf.in` etc.
some EDNS option names, including DAU, DHU, N3U, and CHAIN,
were not printed in dns_message_pseudosectiontotext() or
_psuedosectiontoyaml(); they were displayed as unknown options.
this has been corrected.
that code was also refactored to use switch instead of if/else,
and to look up the option code names in a table to prevent
inconsistencies between the two formats. one such inconsistency
was corrected: the "TCP-KEEPALIVE" option is now always printed
with a hyphen, instead of being "TCP KEEPALIVE" when not using
YAML. the keepalive system test has been updated to expect this.
EDNS options that print DNS names (i.e., CHAIN and Report-Channel)
now enclose them in quotation marks to ensure YAML correctness.
the auth system test has been updated to expect this when grepping
for Report-Channel options.
Report-Channel and ZONEVERSION EDNS options can now be sent
using `dig +ednsopt=report-channel` (or `dig +ednsopt=rc` for
short), and `dig +ednsopt=zoneversion`.
Coverity Scan reported a new issue for the ksr system test. There
is allegedly a null pointer dereference (FORWARD_NULL) in check_keys().
This popped up because previously we set 'retired' to 0 in case of
unlimited lifetime, but we changed it to None.
It is actually a false positive, because if lifetime is unlimited
there will be only one key in 'keys'.
However, the code would be better if we always initialized 'active'
and if it is not the first key and retired is set, set the successor
key's active time to the retire time of the predecessor key.
The test_ksr_twotwone may fail if the key id is shorter than 5 digits.
Add a leading space to the expected strings which start with the key
tag to avoid the issue.
The pytest collection mechanism has been overhauled in pytest 8.0.0,
resulting in a different node tree when collecting the tests. Ensure the
paths / names we're using that are derived from the node tree are
consistent across different pytest versions.
Particularly, this has affected the convenience symlink name (which is
supposed to be in the form of e.g. dns64_sh_dns64 for the dns64 module
and tests_sh_dns64.py module) and the test name that's logged at the
start of the test, which is supposed to include the system test
directory relative to the root system test directory as well as the
module name (e.g. dns64/tests_sh_dns64.py).
Related https://github.com/pytest-dev/pytest/issues/7777
RFC 9567 section 8.1 specifies that the agent domain cannot
be a subdomain of the domain it is reporting on. therefore,
in addition to making it illegal to configure that at the
zone level, we also need to disable send-report-channel for
any zone for which the global send-report-channel value is
a subdomain.
we also now warn if send-report-channel is configured
globally to a zone that we host, but that zone doesn't
have log-report-channel set.
the logging of error-report queries is no longer activated by
the view's "send-report-channel" option; that now only configures
the agent-domain value that is to be sent in authoritative
responses. the warning that was logged when "send-agent-domain"
was set to a value that is not a locally configured zone has
been removed.
error-report logging is now activated by the presence of an
authoritative zone with the "log-report-channel" option set to
"yes". this is not permitted in the root zone.
NOTE: a zone with "log-report-channel yes;" should contain a
"*._er" wildcard, but that requirement is not yet enforced.
add a boolean "log-report-channel" option for primary and
secondary zones, which sets the DNS_ZONEOPT_LOGREPORTS zone
flag. this option is not yet functional.
If send-report-channel is set at the zone level, it will
be stored in the zone object and used instead of the
view-level agent-domain when constructing the EDNS
Report-Channel option.
This commit adds support for the EDNS Report-Channel option,
which is returned in authoritative responses when EDNS is in use.
"send-report-channel" sets the Agent-Domain value that will be
included in EDNS Report-Channel options. This is configurable at
the options/view level; the value is a DNS name. Setting the
Agent-Domain to the root zone (".") disables the option.
When this value has been set, incoming queries matchng the form
_er.<qtype>.<qname>.<extended-error-code>._er.<agent-domain>/TXT
will be logged to the dns-reporting-agent channel at INFO level.
(Note: error reporting queries will only be accepted if sent via
TCP or with a good server cookie. If neither is present, named
returns BADCOOKIE to complete the DNS COOKIE handshake, or TC=1
to switch the client to TCP.)
These are logged to the update category at debug level 99 and
have the following form.
update-policy: using: signer=ddns-key.example.nil, name=updated.example.nil, addr=10.53.0.1, tcp=0, type=A, target=
update-policy: trying: grant zonesub-key.example.nil zonesub TXT
update-policy: next rule: signer does not match identity
update-policy: trying: grant ddns-key.example.nil zonesub ANY
update-policy: matched: grant ddns-key.example.nil zonesub ANY
or
update-policy: using: signer=restricted.example.nil, name=example.nil, addr=10.53.0.1, tcp=0, type=TXT, target=
update-policy: trying: grant zonesub-key.example.nil zonesub TXT
update-policy: next rule: signer does not match identity
update-policy: trying: grant ddns-key.example.nil zonesub ANY
update-policy: next rule: signer does not match identity
update-policy: trying: grant restricted.example.nil zonesub ANY
update-policy: next rule: name/subdomain mismatch
update-policy: no match found
where 'using:' is the calling parameters of dns_ssutable_checkrules,
'trying:' in the rule bing evaluated, "next rule:" is the reason
the rule does not match, "matched:" repeats the matched rule, and
no match found is reported when te set of rules is exhausted.
When working with key timestamps, ensure we correctly set the UTC
timezone in order for the tests to work consistently regardless of the
local time setting.
